FMGS architecture and modes of operation, the FCU knob by knob, flight director and autopilot engagement and warnings, the FMA, and the FAC yaw and flight envelope functions with the A320 speeds.
Exclusive study material prepared by eatpl.in
A320 Aircraft Systems · Chapter 6
Auto Flight System, FCU and Flight Augmentation
How the FMGS is built, how you talk to it through the FCU, how the AP and FD engage and drop out, how to read the FMA, and what the two FACs do.
FLIGHT MANAGEMENT AND GUIDANCE SYSTEMFCUglareshield: short termMCDU 1pedestal: long termMCDU 2(third optional)FMGC 1FMflightmanagementFGAP · FDA/THRFMGC 2FMflightmanagementFGAP · FDA/THRcrosstalkPFD · NDguidance and targetsFlight controlssurfaces, rudder, nose wheelFADECsthrust (via EIUs)FAC 1yaw · flight envelopeFAC 2standby for yawEither FMGC can do the whole job if the other fails
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
FM: navigation and radio tuning, flight planning, performance, displays
FG: autopilot, flight director and autothrust commands
Navigation database: 28-day cycle; 20 min to load, 5 min to crossload
AMI file: THR RED, ACC, EO ACC, PERF and IDLE factors, fuel policy
Performance database: cannot be changed by the airline
Crew can store 20 waypoints, 10 runways, 20 navaids, 5 routes
Inside each FMGCFM: flight management• navigation and radio tuning• flight planning• performance predictions• display managementFG: flight guidance• autopilot commands• flight director commands• autothrust commandsDatabases in each FMGCNavigationnavaids, waypoints, airways, procedures, company routes28-day cycle: 20 min to load, 5 min crossloadAirline modifiable (AMI)THR RED, ACC and EO ACC altitudes, PERF and IDLE factors, fuel policyset by the airlineAircraft performanceengine, aerodynamic and performance modelscannot be changed by the airlineMagnetic variationused to convert true to magneticCrew-stored20 waypoints, 10 runways, 20 navaids, 5 routesentered by the crew
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
Master and slave over crosstalk; any MCDU entry goes to both FMGCs
Independent
Automatic, e.g. different database validity
INDEPENDENT OPERATION on both MCDUs, IND light; each side drives only its own EFIS and RMP. On ground: crossload the database. In flight: same entries on both MCDUs
Single
Automatic when one FMGC fails
That MCDU shows MCDU MENU; prompt gives OPP FMGC IN PROCESS. ND: MAP NOT AVAIL + SET OFFSIDE RNG/MODE, or OFFSIDE FM CONTROL. Set both NDs alike
Back-up navigation
Crew selects it on MCDU MENU after a dual FM failure (some aircraft)
MCDU flight plan with IRS or GPIRS position on the ND; automatic sequencing; no AP/FD NAV mode
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
No AP: FD 1 on → FMGC 1; FD 1 off and FD 2 on → FMGC 2
No AP and no FD: A/THR on FMGC 1
Master uses its onside FD, controls A/THR and both FMAs
Who is master?Is an AP engaged?yesnoOne APBoth APsits own FMGCFMGC 1FD 1 pb on?yesFMGC 1noFD 2 on: FMGC 2No AP, no FD:A/THR on FMGC 1The master FMGC• uses its onside FD for guidance• controls the autothrust• drives FMA 1 and FMA 2• the other FMGC is the slave
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
Push: arm or engage managed guidance (e.g. push HDG → NAV)
Managed: window dashed and white dot lit
Selected: value shown, dot out
The ALT window always shows a crew altitude, never dashes
250TURNpreset or change the valuewindow shows the value; if not pulled it goes back to dashes250PULLselected guidancemode engages on the value in the window; dot goes out---PUSHmanaged guidanceFMGS targets; window dashed; white dot lightsThe ALT window is the exception: it always shows a crew-selected altitude
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
Turn a dashed knob without pulling: window shows target + turn
HDG/TRK and V/S windows: back to dashes after 45 s
SPD/MACH window: back to dashes after 10 s
A V/S preselected and not engaged within 45 s is cancelled
This timing rule does not apply to the ALT knob
Same FCU, two ways of flyingManaged: FMGS targetsSPDMACH---HDGTRKLAT---HDG V/STRK FPAALT35000LVL/CHV/SFPA-----SPDMACHLOCHDGV/STRKFPAAP 1AP 2A/THR1001000EXPEDMETRICALTUPDNPUSHTOLEVELOFFAPPRFCUSelected: crew targetsSPDMACH280HDGTRKLAT095HDG V/STRK FPAALT35000LVL/CHV/SFPA+1500SPDMACHLOCHDGV/STRKFPAAP 1AP 2A/THR1001000EXPEDMETRICALTUPDNPUSHTOLEVELOFFAPPRFCUDashes and lit dots = managed · numbers and dots out = selectedSelected guidance always has priority over managed
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
SPDMACH.78HDGTRKLAT275HDG V/STRK FPAALT29000LVL/CHV/SFPA-----SPDMACHLOCHDGV/STRKFPAAP 1AP 2A/THR1001000EXPEDMETRICALTUPDNPUSHTOLEVELOFFAPPRFCUSPD/MACH knob100 to 399 kt or M .10 to .99; one turn ≈ 32 kt or M .32SPD/MACH pbswaps the speed target for the equivalent Mach, and backHDG/TRK knob0 to 359°; 1° per click; one turn = 32°LOC pbarms, engages or disengages LOC aloneHDG V/S - TRK FPA pbswaps HDG ↔ TRK and V/S ↔ FPA; FD bars ↔ FPV/FPD
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
FD shows FMGC orders on the PFD: FD 1 → PFD 1, FD 2 → PFD 2
HDG V/S: pitch and roll crossbars, shown only if a mode is active on that axis
TRK FPA: fly the FPV onto the flight path director
Yaw bar below 30 ft: RWY on takeoff, FLARE and ROLL OUT at landing
FD pb on the EFIS panel shows or removes the bars
HDG V/S selectedFD crossbars (pitch + roll)TRK FPA selectedFPV + flight path directorYaw bar (below 30 ft): RWY on takeoff,FLARE and ROLL OUT at landingfollow it with the rudder pedals
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
FDs engage automatically at FMGC power-up: FMA shows 1 FD 2, no bars yet
Switched on in flight: FDs engage in HDG V/S or TRK FPA
Go-around (and TCAS RA, if fitted): FD bars come back, FPV reverts to bars
Both FDs off with no AP: modes disengage, A/THR to SPEED/MACH
FD bars removed beyond 25° nose up, 13° nose down, 45° bank
Flight director status on the FMA (column 5)1 FD 2on the ground after power-up: FDs on, no bars, FCU windows dashedBoth FDs off, no APlateral and vertical modes disengage; A/THR goes to SPEED/MACHBoth FDs off, AP onAP stays in its modes; no bars shownOne FD or FMGC failsboth PFDs show the remaining FD (e.g. 1 FD 1)Speed protection, AP offFDs drop out in open climb or descent if bars are not followedBars removedpitch above 25° up or 13° down, or bank above 45°
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
AP moves pitch, roll and yaw surfaces and the nose wheel
Engage with AP 1 or AP 2 pb: airborne at least 5 s; not below 100 ft after takeoff
On ground: one AP if engines not running; drops out at engine start
Two APs only with LOC/G/S, roll out or go-around armed or engaged (AP 1 active)
Engages in the FD modes, or in HDG V/S / TRK FPA if both FDs off
Engaged: pb green, AP 1 (2) on the FMA, higher breakout forces
SPDMACH---HDGTRKLAT---HDG V/STRK FPAALT29000LVL/CHV/SFPA-----SPDMACHLOCHDGV/STRKFPAAP 1AP 2A/THR1001000EXPEDMETRICALTUPDNPUSHTOLEVELOFFAPPRFCUAP11 FD 2A/THRFMA column 5AP 1 pb lit green · AP1 on the FMAAirborne at least 5 sand not below 100 ft after takeoffOn the groundone AP, engines not running; drops out at engine startTwo APsonly with LOC/G/S, roll out or go-around armed or engagedModestakes the FD modes; HDG V/S or TRK FPA if both FDs offFeelhigher breakout forces on sidesticks and pedals
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
AP pb on the FCU, or force on sidestick, rudder pedals or pitch trim wheel
Other AP engaged (outside LOC/G/S, roll out, GA); both levers above MCT on ground
Normal law: high speed or α protection active (α prot + 1°, or α max below 100 ft RA)
Pitch beyond 25° up / 13° down, bank beyond 45°
Rudder more than 10° out of trim
AP 1 or AP 2 disengages when…Crew action• takeover pb pressed (standard)• AP pb pressed on the FCU• sidestick pushed beyond a threshold• rudder pedals beyond a threshold• pitch trim wheel moved beyond a threshold• the other AP is engaged (outside LOC/G/S, roll out, GA)• both thrust levers above MCT on the groundProtections (normal law)• high speed protection active• α prot + 1° reached (lift-off to 100 ft RA on landing)• α max reached (below 100 ft RA on landing)• pitch above 25° up or 13° down, bank above 45°• rudder more than 10° out of trim• or any engagement condition is lostAP pb light out and AP 1 (2) removed from the FMA
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
SPEEDALT*G/SHDGLOCCAT 3SINGLERADIO 100AP11 FD 2A/THR1A/THRthrust mode; autobrake on some aircraft2AP/FD verticalengaged · armed3AP/FD lateralengaged · armed4Approach capabilityCAT and minimum5Engagement statusAP · FD · A/THRLine 1engaged modesgreenLine 2armed modesblue (magenta when due to a constraint)Line 3messages and more armed modeswhite, amber or redA white box is drawn round each new annunciation for 10 s (longer for some reversions with a triple click)
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
Flight envelope: PFD speed scale and alpha floor signal
Low energy alert and windshear detection (if installed)
FAC 1 active for yaw, FAC 2 standby; FAC 2 takes over any failed channel
FAC pb (flight control overhead) OFF but FAC valid: envelope still works
FAC 1 feeds FD 1 and PFD 1; FAC 2 feeds FD 2 and PFD 2
Two FACs, four functionsFAC 1active for yaw functionsFAC 2standby for yaw functionsYawyaw damping and turn coordination · rudder trim · rudder travel limitFlight envelopePFD speed scale: VLS, VFE, VMAX, F, S, green dot, α prot · alpha floorLow energySPEED SPEED SPEED aural alert (if installed)WindshearWINDSHEAR warning at takeoff and approach (if installed)• Both engage automatically at power-up• FAC 2 takes over any channel that fails in FAC 1• FAC 1 → FD 1 and PFD 1 · FAC 2 → FD 2 and PFD 2• FAC pb OFF but FAC valid: flight envelope still works• Talks to the ELACs with AP off, to the FMGS with AP on
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
AP on at takeoff and go-around: short-term yaw help after an engine failure
AP on: FMGS orders yaw damping in approach and runway alignment in ROLL OUT
Rudder trim: crew trim knob, or FMGS orders with AP on (long-term engine-out compensation)
AP on: the rudder trim knob is inoperative
Rudder pushed more than 10° out of trim: AP disengages
Dutch roll after a disturbancetimeyawyaw damper off: lightly dampedyaw damper on: rudder opposes the yaw rateYaw dampingstability in yaw and turn coordinationAP on: short termhelps the rudder after an engine failure at takeoff or GARudder trimtrim knob; with AP on the FMGS trims (knob inoperative)AP disconnectrudder pushed more than 10° out of trim
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
FAC limits rudder deflection with speed to avoid high structural loads
Full travel at low speed: 25° up to 160 kt, or 30° up to 140 kt on other standards
About 3.4° on the A320 (2.9° on the A321) at high speed
Slats extended: limit set to the low-speed (maximum) value
Both FACs lost: limit frozen at the value of the second failure
1001502002503003504000°10°20°30°calibrated airspeed (kt)max rudder deflection25° up to 160 kt30° up to 140 kt (other standard)about 3.4° (A320) at 380 ktSlats out: limit goes to the low-speed (full) valueBoth FACs lost: limit frozen where it was
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
406080100120140160180200220240FSCONF 2 approachVMAXred and black: VMO, VLE or VFEVFE NEXTamber =: next flap positionSslat retraction / CONF 1 targetSpeed trendyellow arrow: speed in 10 sTargetmagenta managed · blue selectedFflap retraction / CONF 2, 3 targetVLStop of amber stripα prottop of black and amber stripα maxtop of red stripComputed by the FAC; also sent to the FMGC as guidance limits
FAC computes VS1g and a gross weight: below 14 625 ft and 250 kt from α, speed, altitude, thrust and CG; above, from a memorised weight and a fuel model.
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
1 g stall speed; conventional VSmin ≈ 0.94 VS1g, so V2 = 1.2 × 0.94 = 1.13 VS, VREF = 1.3 × 0.94 = 1.23 VS
VLS
top of amber strip
1.13 VS at takeoff or touch and go · 1.23 VS after one flap step · 1.28 VS clean; Mach corrected above 20 000 ft (0.2 g buffet margin); up with speedbrakes
F
"F"
minimum flap retraction speed at takeoff; approach target in CONF 2 and 3; about 1.18–1.26 VS of CONF 1+F
S
"S"
minimum slat retraction speed at takeoff; approach target in CONF 1; about 1.22–1.25 VS clean
Green dot
green circle
engine-out clean speed, best lift/drag, final takeoff speed; 2 × weight (t) + 85 below 20 000 ft, +1 kt per 1 000 ft above (other formula on some aircraft)
Worked example
64 t, FL 310
green dot = 2 × 64 + 85 = 213 kt; FL 310 is 11 000 ft above 20 000: + 11 = 224 kt
Chapter 6 · Auto Flight System, FCU and Flight Augmentation
VMC, VFE, VMAX, α prot and the takeoff and approach speeds
Speed
Meaning
VMCG · VMCA · VMCL
minimum control speed on the ground (primary controls only) · in flight, takeoff flaps · in flight, approach flaps (max 5° bank, other engine at takeoff thrust)
VA · VMO · VLE · VLO
design manoeuvring speed (full deflection, alternate or direct law) · maximum speed · gear extended · gear operating
VFE · VFE NEXT · VMAX
max per flap configuration · max for the next position · VMAX = VMO (MMO), VLE or VFE, bottom of the red and black strip
Vα PROT · Vα MAX
α protection starts (top of black and amber strip) · max α in normal law (top of red strip); display only, ELAC does the protection
VSW
stall warning speed: red and black strip when normal law is lost
V1 · VR · V2
crew inserted on the MCDU TAKEOFF page; V2 shown by the speed select symbol, at least 1.13 VS
VREF · VAPP
1.23 VS CONF FULL · VLS + wind correction (5 to 15 kt); at least VLS + 5 with A/THR on, autoland, ice or gusty crosswind above 20 kt
Chapter 6 · Auto Flight System, FCU and Flight Augmentation