A320 Aircraft Systems · Chapter 23
Brakes, Anti-skid and Autobrake How the A320 stops: carbon brakes on two independent hydraulic systems, the BSCU and ABCU, anti-skid, autobrake, the parking brake and the WHEEL page.
AUTO/BRK LO DECEL ON MED DECEL ON MAX DECEL ON 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL ANTI SKID NORM BRK G ALTN BRK Y ACCU PR AUTO BRK MED © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the brakes of the A320. On every landing these four carbon brakes bring a heavy airliner to a stop, and on a rejected take-off they may have to do it from close to take-off speed. In this lesson we follow the two independent brake systems, normal on green and alternate on yellow with its accumulator, and the two computers that control them. We will see how anti-skid keeps each wheel at the edge of a skid, how the autobrake arms and activates, how the parking brake works, and how to read the triple indicator and the WHEEL page. Finally we put it all together in the failure cases examiners like to ask about.
Brakes
Our route through ATA 32-30 AUTO/BRK LO DECEL ON MED DECEL ON MAX DECEL ON A/SKID & N/W STRG ON OFF BRK FAN HOT ON 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 PARK BRK OFF ON PARK BRK WHEEL 120 1 135 2 110 3 125 4 °C REL °C REL AUTO BRK MED Architecture Carbon brakes, green normal system, yellow alternate with accumulator, BSCU and ABCU.
Braking modes Normal, alternate with and without anti-skid, parking brake.
Anti-skid and autobrake How each wheel is kept at the edge of a skid, and how LO, MED and MAX work.
Indications Triple indicator, brake temperatures and fans, WHEEL page, memos and failures.
Chapter 23 · Brakes, Anti-skid and Autobrake
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the brakes. We start with the architecture: four carbon brakes, two independent hydraulic systems to drive them, and the two control units, one for normal braking and one for alternate braking. Then the four braking modes, which is where most exam questions live: normal, alternate with anti-skid, alternate without anti-skid, and the parking brake. Next we look at anti-skid, how it decides when a wheel is about to skid, and at the autobrake, its three modes, when it arms, when it actually brakes and how it lets go. Finally the cockpit: the triple pressure indicator, brake temperatures and fans, the braking half of the WHEEL page and the memos, and a set of failure cases to tie it all together.
Architecture
Four carbon brakes, two systems Each main wheel has a carbon multidisc brake ; the nose wheels have none Normal system: green hydraulic pressureAlternate system: yellow , backed up by an accumulator Commands: brake pedals or the autobrake Fusible plugs in the main wheels; brake fans for fast cooling1 2 3 4 Main wheels 1 to 4 carbon multidisc brakes fusible plugs, brake fans Two brake systems normal: green alternate: yellow + accumulator
Chapter 23 · Brakes, Anti-skid and Autobrake
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 brakes only its four main wheels. Each one carries a carbon multidisc brake, a stack of rotating and stationary discs that hydraulic pistons squeeze together. The nose wheels have no brakes. Either of two independent brake systems can drive these four brakes. The normal system uses green hydraulic pressure. The alternate system uses yellow, and it is backed up by a hydraulic accumulator, so you still have brakes with no yellow pump running. The braking command comes either from the pilots, through the brake pedals, or from the autobrake, at a deceleration rate the crew has selected. Two more items sit on the main wheels in the bays: fusible plugs, which protect against a tyre burst after an overheat, and brake cooling fans, which let you cool the brakes quickly between flights.
Architecture
The BSCU and the ABCU BSCU : dual channel; normal braking, anti-skid , nose wheel steering Channel changeover at every gear DOWN selection, or on failure Also: residual pressure check, brake temperature , wheel speeds to other systems ABCU : the alternate braking control unitEvery braking component is monitored : failures go to ECAM BSCU: Brake and Steering Control Unit CHANNEL 1 normal braking · anti-skid nose wheel steering CHANNEL 2 normal braking · anti-skid nose wheel steering Changeover between channels at every gear lever DOWN selection, or if one channel fails Secondary functions 1 checks residual pressure in the brakes 2 monitors brake temperature 3 sends wheel speed information to other systems Alternate braking is controlled by a separate unit: the ABCU
Chapter 23 · Brakes, Anti-skid and Autobrake
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two computers run the brakes. The brake and steering control unit, the B S C U, has two channels, and in normal operation it controls normal braking and anti-skid, and, as we saw last lesson, nose wheel steering. A changeover between its two channels happens every time the gear lever is selected down, and also if one channel fails. So, much like the gear control units, both channels are used in turn. The B S C U has some secondary jobs too: it checks for residual pressure left in the brakes, it monitors brake temperature, and it supplies wheel speed information to other aircraft systems. The second computer is the alternate braking control unit, the A B C U, which takes over the braking when the system reverts to alternate. Every normal and alternate component is monitored, and any detected failure is shown on ECAM.
Architecture
The braking schematic GREEN YELLOW brake accumulator NORM BRK SEL VALVE NORMAL SERVO VALVE ALTN BRK SEL VALVE ALTN SERVO VALVE PARK BRK control valve brakes (each main wheel) BSCU (2 channels) normal braking anti-skid nose wheel steering ABCU alternate with anti-skid alternate without anti-skid alternate on accumulator Brake pedals AUTO/BRK · A/SKID sw wheel tachometer 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 BRAKES and ACCU PRESS indicator hydraulic electrical At skid onset the BSCU sends release orders to both the normal and the alternate servo valves, and to ECAM.
Chapter 23 · Brakes, Anti-skid and Autobrake
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole system on one page. On the left, green comes down through the normal brake selector valve and then the normal servo valve to the brakes. The B S C U opens the selector valve and drives the servo valve, which sets the pressure for each brake and releases it for anti-skid. On the right, yellow comes down, backed by the brake accumulator, through the alternate brake selector valve and the alternate servo valve. These are worked by the A B C U. In parallel with the alternate selector valve sits the parking brake control valve. The pedals feed both computers, and wheel tachometers tell the B S C U how fast each wheel is turning. Top right is the triple indicator, which reads the accumulator and the yellow pressures going to the brakes.
Braking modes
Four braking modes NORMAL G BSCU ALTN + A/SKID Y ABCU + BSCU ALTN, no A/SKID Y / ACCU ABCU PARKING Y / ACCU control valve Normal Green and switch ON. Anti-skid and autobrake available. No pressure indication.
Alternate with anti-skid Green insufficient, yellow available, switch ON, parking brake not ON. No autobrake.
Alternate without anti-skid Anti-skid lost electrically or hydraulically. Limited to 1 000 PSI.
Parking brake Yellow or accumulator via the parking brake control valve, full pressure.
Chapter 23 · Brakes, Anti-skid and Autobrake
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The reference describes four braking modes, and you should be able to recite them. Normal braking, on green, with anti-skid working and autobrake available. Alternate braking with anti-skid, on yellow, when green is not enough: the A B C U does the braking and the B S C U still provides anti-skid, but autobrake is lost. Alternate braking without anti-skid, still on yellow or on the accumulator alone, with brake pressure limited to one thousand P S I to protect the tyres. And the parking brake, using yellow or the accumulator through the parking brake control valve at full pressure. Notice the pattern. As you step down the list, you keep braking, but you lose first the autobrake, then the anti-skid. We will now take each mode in turn.
Braking modes
Normal braking Needs green pressure and the A/SKID & N/W STRG switch ON Anti-skid operative , autobrake available Electrical control by the BSCU : pedals, autobrake , or gear UP in flight Anti-skid through the normal servo valves No brake pressure indication in the cockpitGREEN NORM BRK SEL VALVE NORMAL SERVO VALVE Commands via the BSCU pilot pedals autobrake (on ground) gear lever UP (in flight) Anti-skid through the normal servo valves No pressure gauge in normal
Chapter 23 · Brakes, Anti-skid and Autobrake
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Normal braking is what you use every day. It needs two things: green hydraulic pressure, and the A SKID and N W STRG switch on. In this mode the anti-skid works and the autobrake is available. Braking is controlled electrically through the B S C U. Watch what happens when the pilot presses the pedals: the B S C U opens the normal servo valve, green pressure flows to the brake pistons, the discs clamp together and the wheel slows down. The same path is used on the ground by the autobrake, and in flight, automatically, when the gear lever is selected up, to stop the wheels spinning before they enter the bay. Anti-skid also works through these normal servo valves. One trap: there is no brake pressure indication at all in normal braking. The triple indicator only shows yellow pressures.
Braking modes
Alternate braking with anti-skid When green is insufficient , with yellow available Switch ON and the parking brake not ON ABCU energises the ALTN BRK SEL valve and drives the ALTN servo valve Anti-skid still by the BSCU ; autobrake inoperative Triple indicator shows the brake pressures YELLOW ALTN BRK SEL VALVE energised by the ABCU ALTN SERVO VALVE pressure set by the ABCU 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 triple indicator now reads the brake pressures BSCU still does anti-skid
Chapter 23 · Brakes, Anti-skid and Autobrake
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
If green pressure becomes insufficient, braking changes over automatically to alternate with anti-skid, provided three conditions are met: yellow pressure is available, the A SKID and N W STRG switch is on, and the parking brake is not on. The pedal inputs now go to the A B C U. Taking the pedal input into account, it energises the alternate brake selector valve, which lets yellow into the alternate circuit, and it controls the alternate servo valve electrically to give the right pressure to each brake. The B S C U still looks after anti-skid. Because yellow now controls the brakes, the triple indicator shows the pressures delivered to the left and right brakes. Autobrake is lost in this mode. And a handling note: the first part of pedal travel gives more braking in alternate than in normal, so be gentle.
Braking modes
Alternate braking without anti-skid Anti-skid off electrically : switch OFF , power failure or BSCU failure Or hydraulically : green and yellow low pressure, accumulator only The ABCU controls the alternate valves from the pedals Brake pressure limited to 1 000 PSI Accumulator: at least 7 full brake applications Anti-skid lost: two ways Electrically • A/SKID & N/W STRG OFF • power supply failure • BSCU failure Hydraulically • green and yellow both low pressure • brakes on the accumulator only 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Brake pressure limited to 1 000 PSI avoids wheel lock and limits tyre-burst risk Accumulator alone at least 7 full brake applications
Chapter 23 · Brakes, Anti-skid and Autobrake
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the third mode both autobrake and anti-skid are lost. Anti-skid can be deactivated in two ways. Electrically, if the A SKID and N W STRG switch is off, if there is a power supply failure, or if the B S C U fails. Or hydraulically, if both green and yellow are at low pressure, so the brakes are supplied by the brake accumulator alone. The A B C U still drives the alternate selector valve and servo valve according to the pedal demand. Without anti-skid, nothing stops a wheel locking, so brake pressure is automatically limited to one thousand P S I, to avoid wheel lock and limit the risk of tyre burst. On the accumulator alone, plan on at least seven full brake applications, so avoid pumping the pedals. And again, initial pedal travel gives more braking than in normal.
Controls
The A/SKID & N/W STRG switch ON : normal braking with anti-skid when green is availableON, green lost: yellow takes over automatically ; anti-skid and steering remain OFF : yellow supplies the brakes, no anti-skid , limited to 1 000 PSI OFF: nose wheel steering lost ; differential braking by the pedals remains Triple indicator shows yellow brake pressure A/SKID & N/W STRG ON OFF A/SKID & N/W STRG ON OFF ON green available: normal braking, anti-skid green lost: yellow takes over by itself; anti-skid and steering remain OFF yellow supplies the brakes anti-skid off: limited to 1 000 PSI nose wheel steering lost differential braking still by pedals With the switch OFF the triple indicator shows yellow brake pressure
Chapter 23 · Brakes, Anti-skid and Autobrake
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
One switch on the centre panel controls both anti-skid and nose wheel steering. With it on, and green available, you have normal braking with anti-skid. If green is lost with the switch on, yellow automatically takes over the brakes, anti-skid and nose wheel steering both remain, and the triple indicator starts showing yellow brake pressure. Now select it off. Yellow supplies the brakes, anti-skid is deactivated and brake pressure is limited to one thousand P S I. Nose wheel steering is lost too, because the same switch removes it. You can still steer with differential braking through the pedals, pressing harder on one side. Remember this switch when an exam question says the aircraft has no steering and no anti-skid after a particular failure, and ask yourself whether the crew simply selected it off.
Anti-skid
How anti-skid works Each wheel speed (tachometer ) is compared with a reference speed Below about 0.87 × reference : release orders keep the slip at that value Reference from ADIRU 1, 2 or 3 horizontal acceleration All ADIRUs failed: reference = highest main wheel speed Inactive below 20 kt ground speed 80 90 100 110 120 0 1 2 3 4 5 6 reference speed (ADIRU) wheel speed (tachometer) 0.87 × reference: release time (s) speed (kt) Example: reference 120 kt → release below about 104 kt illustration only; the real ratio depends on conditions
Chapter 23 · Brakes, Anti-skid and Autobrake
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Anti-skid keeps each wheel at the limit of an impending skid, which is where braking is most efficient. A tachometer measures the speed of each main wheel, and the B S C U compares it with the aircraft's reference speed. If a wheel slows below roughly zero point eight seven times the reference, depending on conditions, the unit sends release orders to keep the slip at that value. Look at the trace: the wheel slows under braking, touches the release line, spins up again and the brake is reapplied. For a reference of one hundred and twenty knots, release starts below about one hundred and four knots. Normally the reference speed comes from the horizontal acceleration of ADIRU one, two or three. If all three fail, it equals the highest main wheel speed. Anti-skid switches off below twenty knots ground speed.
Anti-skid
Anti-skid: four facts examiners like Anti-skid works in normal braking and in alternate braking with anti-skid.
Both servo valves Release orders go to the normal and the alternate servo valves, and to ECAM, which shows the released brakes.
Full pedal Without autobrake, full braking performance needs the pedals at full deflection.
20 kt Anti-skid is deactivated below 20 kt ground speed, so it never stops you parking.
One switch A/SKID & N/W STRG OFF removes anti-skid and steering together.
Chapter 23 · Brakes, Anti-skid and Autobrake
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are four anti-skid facts that come up again and again. First, when a skid starts, the B S C U sends release orders to both the normal and the alternate servo valves, so anti-skid works whichever system is braking, and ECAM shows which brakes are being released. Second, without autobrake, you only get full braking performance with the pedals pushed to full deflection, which is exactly what you do in a rejected take-off with no autobrake. Third, anti-skid is deactivated below twenty knots ground speed, which is why you can bring the aircraft to a complete stop and taxi slowly without it interfering. Fourth, the same switch controls anti-skid and nose wheel steering, so selecting it off removes both. Keep those four in mind for the failure questions at the end.
Autobrake
The AUTO/BRK panel Purpose: shorter stop in a rejected take-off ; set deceleration on landing Spring-loaded LO , MED , MAX pushbuttons MAX for take-off; LO or MED for landingON blue: armed · DECEL green: 80 % of the selected rateNo DECEL on a slippery runway does not mean no autobrake AUTO/BRK LO DECEL ON MED DECEL ON MAX DECEL ON not armed all lights out AUTO/BRK LO DECEL ON MED DECEL ON MAX DECEL ON MAX armed blue ON: take-off AUTO/BRK LO DECEL ON MED DECEL ON MAX DECEL ON MED active green DECEL: at least 80 % of the selected rate Spring-loaded pushbuttons: press to arm, press again to disarm
Chapter 23 · Brakes, Anti-skid and Autobrake
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The autobrake has two purposes. On take-off, it reduces the stopping distance if you have to reject. On landing, it sets up and holds a chosen deceleration, which is more comfortable for passengers and saves crew workload. The AUTO BRK panel has three spring-loaded pushbuttons, LO, MED and MAX. MAX is normally selected for take-off, LO or MED for landing. Pressing one arms that rate, and its ON light comes on blue. When the actual deceleration reaches eighty per cent of the selected rate, the green DECEL light comes on. Here is a classic trap. On a slippery runway the anti-skid may stop the aircraft reaching the selected deceleration, so DECEL may never light. That does not mean the autobrake is not working. It is braking as hard as the runway allows.
Autobrake
Arming the autobrake Green pressure availableAnti-skid electrically powered No failure in the braking systemAt least one ADIRU available Can arm with the parking brake ON ; MAX not in flight green pressure available anti-skid electrically powered no failure in the braking system at least one ADIRU available AND can arm Good to know it can be armed with the parking brake ON MAX cannot be armed in flight AUTO BRK MED memo, also shown on the FMA: blue armed, green active
Chapter 23 · Brakes, Anti-skid and Autobrake
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
To arm the autobrake you press LO, MED or MAX, but it only arms if four conditions are met. Green pressure must be available, because autobrake works through normal braking. Anti-skid must be electrically powered. There must be no failure in the braking system. And at least one ADIRU must be available, since the system needs a reference for deceleration. Two details often appear in exams. You may arm the autobrake with the parking brake on, so you can arm MAX during your before take-off flow. But MAX cannot be armed in flight. For landing you choose LO or MED. Once armed, the mode shows in blue on the flight mode annunciator, and in green when it is actually braking. The AUTO BRK memo on ECAM also shows which rate you have selected.
Autobrake
Activation and deceleration rates LO, MED: active at the ground spoiler extension order MAX: ground spoiler order and wheel speed above 40 kt MAX: maximum pressure at once MED: 3 m/s² , LO: 2 m/s² , both after 2 s Needs two SECs ; RTO below 72 kt : no spoilers, no autobrake After the ground spoiler order 0 s 1 s 2 s 3 s 4 s 5 s spoilers MAX full pressure at once MED 3 m/s² (9.8 ft/s²) LO 2 m/s² (6.6 ft/s²) On some aircraft LO starts after 4 s at 1.7 m/s² (5.6 ft/s²). Activation LO, MED: ground spoiler extension order MAX: ground spoiler order and wheel speed above 40 kt at least two SECs operative
Chapter 23 · Brakes, Anti-skid and Autobrake
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Arming is not braking. The autobrake actually activates when the ground spoiler extension order is detected. For LO and MED that is the only trigger. For MAX the wheel speed must also be above forty knots. In a rejected take-off with MAX armed, maximum pressure goes to the brakes as soon as the spoiler order comes. On landing, MED sends progressive pressure two seconds after the spoilers deploy, for a deceleration of three metres per second squared, and LO does the same for two metres per second squared. On some aircraft LO waits four seconds and aims for one point seven. Now the trap: the ground spoilers do not extend if you reject below seventy two knots wheel speed, so the autobrake does not activate either. Brake manually. Also, at least two spoiler elevator computers must be working.
Autobrake
Worked example: LO or MED? Touchdown 130 kt = 66.9 m/s 2 s before braking: 66.9 × 2 ≈ 134 m LO: 66.9² ÷ (2 × 2) ≈ 1 118 m → total ≈ 1 250 m MED: 66.9² ÷ (2 × 3) ≈ 745 m → total ≈ 880 m Real stops are shorter: reversers and drag add deceleration 0 20 40 60 80 100 120 140 0 200 400 600 800 1000 1200 1400 LO ≈ 1250 m MED ≈ 880 m distance from spoiler deployment (m) ground speed (kt) 130 kt = 66.9 m/s · 2 s delay = 134 m · then v² ÷ 2a autobrake alone: no reversers, no drag
Chapter 23 · Brakes, Anti-skid and Autobrake
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put numbers on the two landing modes. Imagine the spoilers deploy at one hundred and thirty knots, which is about sixty seven metres per second. For two seconds nothing happens, so we roll about one hundred and thirty four metres. Then the autobrake holds a steady rate. Distance equals speed squared over twice the deceleration. With LO at two metres per second squared, that is about one thousand one hundred and eighteen metres, so roughly one thousand two hundred and fifty in total. With MED at three, about seven hundred and forty five, so roughly eight hundred and eighty in total. MED saves about three hundred and seventy metres. This counts the autobrake alone; reversers and aerodynamic drag help in real life. The point is the scale of the difference, which is why the choice matters on a short or wet runway.
Autobrake
Deactivation and disarming Deactivates if disarmed, or if the ground spoilers retract (stays armed)Disarms : pushbutton pressed, or an arming condition lost Disarms after take-off or a touch-and-go Disarms with enough deflection of at least one pedal WHEEL page: AUTO BRK flashes green for 10 s DEACTIVATES (braking stops) the system is disarmed, or the ground spoilers retract: it then stays ARMED DISARMS (ON light out) • pushbutton pressed • an arming condition lost • after take-off or touch-and-go • enough pedal deflection on at least one pedal WHEEL 150 1 170 2 160 3 150 4 °C REL °C REL AUTO BRK (flashing) MED WHEEL page: AUTO BRK flashes green for 10 s after disengagement Pedal override: the usual way to take over after landing
Chapter 23 · Brakes, Anti-skid and Autobrake
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two words to keep apart: deactivate and disarm. The autobrake deactivates, meaning it stops braking, when it is disarmed, or when the ground spoilers retract. In that second case it remains armed, so if the spoilers deploy again it will brake again. Disarming is more final: the ON light goes out. The system disarms if you press the pushbutton, if any arming condition is lost, after take-off or a touch-and-go, or when the pilot applies enough deflection to at least one brake pedal while the autobrake is active. That pedal override is how you normally take over after landing, smoothly, at a speed you choose. When the autobrake disengages, AUTO BRK on the WHEEL page flashes green for ten seconds, so the other pilot can see that braking is now manual.
Parking brake
The parking brake Pull the PARK BRK handle, turn it clockwise to ON Yellow or the accumulator , through the parking brake control valve Full pressure on the main wheel brakes; held at least 12 h No yellow or accumulator pressure: the pedals still give normal brakes Yellow ELEC pump recharges the accumulatorPARK BRK OFF ON PARK BRK pull, turn clockwise to ON 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Parking brake ON yellow, or the accumulator, through the control valve full pressure on the main wheel brakes accumulator holds it for at least 12 h Remember pointer not at ON: parking brake NOT set yellow ELEC pump recharges the accumulator no yellow or accumulator pressure: use the pedals (normal brakes)
Chapter 23 · Brakes, Anti-skid and Autobrake
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The parking brake handle is on the pedestal: pull it, then turn it clockwise to ON, and the PARK BRK memo appears on ECAM. Look at the pointer, because if it is not at ON, the parking brake is not on. The brakes are supplied by yellow, or by the accumulator, through the parking brake control valve, which opens and applies full pressure to the main wheel brakes. The accumulator can hold that parking pressure for at least twelve hours. If the parking brake is on but there is no yellow or accumulator pressure, the pedals still give you normal braking on green. And if the accumulator is low on the ground, you recharge it simply by switching on the yellow electric pump. Finally, remember that alternate braking with anti-skid needs the parking brake off.
Parking brake
Inside: the accumulator holds the brakes Nitrogen pre-charge pushes the fluid outHandle ON: the control valve opens Accumulator pressure falls a little as the pistons fill Read it on the ACCU needle of the triple indicator At least 7 full applications in alternate without pumps PARK BRK OFF ON PARK BRK pull, turn clockwise to ON 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Parking brake ON yellow, or the accumulator, through the control valve full pressure on the main wheel brakes accumulator holds it for at least 12 h Remember pointer not at ON: parking brake NOT set yellow ELEC pump recharges the accumulator no yellow or accumulator pressure: use the pedals (normal brakes)
Chapter 23 · Brakes, Anti-skid and Autobrake
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what happens inside when you set the parking brake with the pumps off. The brake accumulator is a cylinder with nitrogen above a free piston and yellow fluid below. As the handle goes to ON, the parking brake control valve opens, and the stored fluid flows to the brake pistons, giving full pressure on the brakes. Watch the accumulator piston move and the gauge drop a little: the gas expands slightly as it pushes fluid out, so the accumulator pressure falls. That is the same pressure you read on the ACCU needle of the triple indicator. The same accumulator stands behind alternate braking, where it can give at least seven full applications on its own. If the needle is low before the tug arrives, switch on the yellow electric pump to recharge it.
Indications
The BRAKES and ACCU PRESS indicator ACCU : pressure in the yellow brake accumulatorBRAKES : yellow pressure to the left and right brakesMeasured upstream of the alternate servo valves Brake pressures shown only when yellow controls the brakes That is alternate braking or the parking brake 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Normal braking brakes read zero: green not shown 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Parking brake ON yellow or accumulator pressure 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Alternate, no anti-skid limited to 1 000 PSI 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 Alternate with anti-skid pressure follows the pedals
Chapter 23 · Brakes, Anti-skid and Autobrake
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The triple indicator on the centre panel has three needles. The upper one shows the pressure in the yellow brake accumulator. The two lower ones show the yellow pressure delivered to the left and right brakes, measured upstream of the alternate servo valves. The key point is that brake pressure is only indicated when the yellow system controls the brake pressure, that is when alternate braking is active or the parking brake is applied. In normal braking on green the brake needles stay at zero, however hard you press. So, in the top left you see normal braking. Top right, the parking brake is set. Bottom left, alternate braking without anti-skid, capped at one thousand P S I. Bottom right, alternate braking with anti-skid, where the pressures follow the pedals.
Indications
The WHEEL page: braking WHEEL 120 1 185 2 150 3 140 4 °C REL °C REL ANTI SKID NORM BRK G ALTN BRK Y ACCU PR AUTO BRK MED TAT +19 °C SAT +18 °C 14 H 05 GW 64200 KG 1 2 3 4 5 6 7 1 Brake temperature green; arc on the hottest above 100 °C, amber above 300 °C 2 Wheel number and REL release indicators amber: brake released fault 3 ANTI SKID amber: lost (with BSCU channel numbers); green: still available 4 NORM BRK + G green: available; amber: normal braking lost 5 ALTN BRK + Y green: in use or available; amber: failed 6 ACCU PR / ACCU ONLY yellow available, or accumulator alone 7 AUTO BRK + mode green armed; flashes after disengaging; amber failed
Chapter 23 · Brakes, Anti-skid and Autobrake
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the lower half of the WHEEL page. Tag one: each brake temperature, normally green. When one brake exceeds one hundred degrees, a green arc appears over the hottest wheel, and it turns amber, with an ECAM caution, above three hundred degrees. Tag two: the white wheel numbers, with release indicators beside them that turn amber for a brake released fault. Tag three: ANTI SKID. It is amber, with a caution, if anti-skid is lost, with the failed B S C U channel numbers beside it, and green if another part of braking has failed but anti-skid is still available. Tags four and five: NORM BRK with its G, and ALTN BRK with its Y. Tag six: ACCU PR or ACCU ONLY. Tag seven: AUTO BRK with the selected mode.
Indications
Reading the braking legends after a failure WHEEL 90 1 95 2 90 3 85 4 °C REL °C REL ANTI SKID NORM BRK G ALTN BRK Y ACCU PR Green lost alternate with anti-skid WHEEL 90 1 95 2 90 3 85 4 °C REL °C REL ANTI SKID 1 2 NORM BRK G ALTN BRK Y ACCU PR BSCU lost (both channels) alternate, no anti-skid WHEEL 90 1 95 2 90 3 85 4 °C REL °C REL NORM BRK G ALTN BRK Y ACCU ONLY Green and yellow lost accumulator only WHEEL 90 1 95 2 90 3 85 4 °C REL °C REL ANTI SKID NORM BRK G ALTN BRK Y ACCU PR AUTO BRK Autobrake failed AUTO BRK amber Legends appear only when something has failed: amber is lost, green is what you still have.
Chapter 23 · Brakes, Anti-skid and Autobrake
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The braking legends stay hidden until something fails, and then they tell you exactly what you have left. Green lost, top left: NORM BRK and its G are amber, ALTN BRK and Y are green, ACCU PR green, and ANTI SKID green because you still have it. Both B S C U channels lost, top right: ANTI SKID amber with one and two beside it, NORM BRK amber even though its G is still green, ALTN BRK green. Green and yellow lost, bottom left: NORM BRK amber, ALTN BRK green but with an amber Y, and ACCU ONLY, meaning you are braking on the accumulator alone with at least seven applications. Autobrake failed, bottom right: AUTO BRK amber, and the other legends green to tell you normal and alternate braking and anti-skid are all still there.
Indications
Brake temperature and brake fans BRK FAN ON: fans run if the left main gear is down and locked HOT amber light (with a caution): brakes too hotArc on the hottest brake above 100 °C , amber above 300 °C BSCU monitors brake temperature Fusible plugs protect against tyre burstBRK FAN HOT ON BRK FAN pushbutton ON: fans run if the left main gear is down and locked HOT amber: brakes too hot (+ caution) WHEEL 150 1 320 2 180 3 160 4 °C REL °C REL hottest brake above 300 °C: its arc turns amber, ECAM caution Also fusible plugs in the main wheels protect against tyre burst after an overheat
Chapter 23 · Brakes, Anti-skid and Autobrake
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Brakes turn the aircraft's energy into heat, so temperature matters, especially on short turnarounds. The B S C U monitors each brake temperature and shows it on the WHEEL page. The hottest brake gets an arc once it passes one hundred degrees, and the arc turns amber with an ECAM caution above three hundred degrees. On aircraft fitted with brake fans, the BRK FAN pushbutton is on the centre panel. Press it ON and the fans run, but only if the left main gear is down and locked. Watch the temperature fall as the fans blow air through the hot brake. The HOT light in the same button comes on amber, with a caution, when the brakes get too hot. And if a brake ever overheats badly, fusible plugs in the wheel release the tyre pressure before it can burst.
AUTO BRK LO / MED / MAX : the selected modeAUTO BRK OFF : shown when the autobrake has failed BRK FAN : the BRK FAN pushbutton is ONPARK BRK : parking brake ON, in phases 1, 2, 9 and 10 All in green AUTO BRK MED mode selected (LO, MED or MAX) AUTO BRK OFF autobrake failed BRK FAN BRK FAN pushbutton ON PARK BRK phases 1, 2, 9 and 10 All four memos are green PARK BRK: on the ground before engine start, after landing (phases 1 and 2) and after landing (phases 9 and 10)
Chapter 23 · Brakes, Anti-skid and Autobrake
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Four braking memos can appear in the ECAM memo area, all in green. AUTO BRK followed by LO, MED or MAX tells you which rate you have armed. AUTO BRK OFF is the one to watch: in this reference it appears when the autobrake has failed, so do not read it as a simple reminder that nothing is selected. BRK FAN appears whenever the BRK FAN pushbutton is on, which is a useful reminder to switch the fans off before take-off. And PARK BRK appears when the parking brake is on during flight phases one, two, nine and ten, in other words on the ground before take-off and after landing. A quick memo scan during the before take-off checks should show the autobrake mode you expect, and no BRK FAN or PARK BRK.
Failures
What do I have left? Situation Braking Anti-skid Autobrake Steering All normal Normal (green) Yes Yes Yes Green lost Alternate (yellow) Yes No Yes A/SKID & N/W STRG OFF Alternate (yellow), 1 000 PSI No No No Both BSCU channels lost Alternate (yellow), 1 000 PSI No No No Green and yellow lost Accumulator, 1 000 PSI, 7 applications No No No
Steering is yellow and BSCU; autobrake needs green and a healthy braking system; anti-skid needs the BSCU and green or yellow.
Chapter 23 · Brakes, Anti-skid and Autobrake
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us finish the teaching with the table examiners love. All normal: normal braking on green, with anti-skid, autobrake and steering. Green lost: alternate on yellow, anti-skid still there through the B S C U, autobrake gone, steering still there because it is yellow. A SKID and N W STRG off: alternate on yellow limited to one thousand P S I, no anti-skid, no autobrake, no steering. Both B S C U channels lost: the same picture, because the B S C U does anti-skid and steering. Green and yellow lost: the accumulator alone, one thousand P S I, at least seven applications, and no anti-skid, autobrake or steering. Work out each line from the architecture rather than learning it by heart.
Summary
Brakes in one page AUTO/BRK LO DECEL ON MED DECEL ON MAX DECEL ON A/SKID & N/W STRG ON OFF 0 4 ACCU PRESS 1 3 1 3 0 BRAKES PSI x 1000 PARK BRK OFF ON PARK BRK WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL ANTI SKID NORM BRK G ALTN BRK Y ACCU PR Architecture Carbon brakes on 4 main wheels. Normal: green, BSCU. Alternate: yellow + accumulator, ABCU.
Modes Normal · alternate with anti-skid · alternate without (1 000 PSI, 7 applications on accumulator) · parking.
Anti-skid Release below about 0.87 × reference (ADIRU). Off below 20 kt. Switch OFF removes it and steering.
Autobrake Arms: green, anti-skid, no failure, one ADIRU. Activates on spoiler order (MAX also above 40 kt). 2 SECs.
Parking brake Yellow or accumulator, full pressure, at least 12 h. Pointer must be at ON.
Indications Triple indicator: yellow only. WHEEL page: temperatures, arcs 100 / 300 °C, legends after failures.
Chapter 23 · Brakes, Anti-skid and Autobrake
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull the brakes together. Four carbon brakes on the main wheels, driven by green in normal braking under the B S C U, or by yellow and its accumulator in alternate braking under the A B C U. Four modes, and as you step down them you lose autobrake, then anti-skid, and without anti-skid the pressure is capped at one thousand P S I. Anti-skid releases a wheel below roughly zero point eight seven of the reference speed and stops working below twenty knots. Autobrake arms with green, anti-skid power, no braking failure and one ADIRU, and activates on the ground spoiler order. The parking brake uses yellow or the accumulator at full pressure. And the triple indicator only shows yellow, while the WHEEL page tells you what you have left after a failure.