A320 Aircraft Systems · Chapter 10
Communications How A320 crews tune the radios, talk to ATC, the cabin and the ground, record the flight deck and raise the alarm.
Tune, talk, listen, record and alert RMP 1 ACTIVE STBY/CRS 118.700 121.500 VHF1 VHF2 VHF3 LOAD HF1 SEL HF2 AM STBY NAV NAV VOR ILS GLS MLS ADF INNER ON OFF ACP 1 SELCAL CALL CALL VHF1 CALL VHF2 CALL VHF3 CALL HF1 CALL HF2 MECH INT ATT CAB INT RAD ON VOICE RESET –PA– VOR1 VOR2 MKR LS MLS ADF1 ADF2 RMP · ACP · AMU CIDS · CVR · EVAC ELT · SELCAL © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to communications. On the A320 the radios, the interphones and the passenger address all meet in two small panels on the pedestal: the radio management panel, where you choose frequencies, and the audio control panel, where you choose what you transmit on and what you listen to. In this lesson we will learn both panels key by key, then the VHF and HF radios and SELCAL, then the ways the crew talks to the ground mechanic, the cabin and the passengers, and finally the cockpit voice recorder, the evacuation signal, the cabin alert and the emergency locator transmitter. Interviewers love this chapter, because small details such as the SEL light or audio switching show whether you really know the cockpit.
Lesson roadmap
Communications in four parts ATA 23 . Two pedestal panels do most of the work: the RMP chooses frequencies, the ACP chooses what you hear and where you speak.
1 · Radio tuning Architecture, the RMP , tuning, SEL , LOAD and AM, failures, VHF , HF and SELCAL.
2 · Audio The AMU and the ACP : keys, knobs, call lights, push-to-talk and audio switching .
3 · Internal Flight, cabin and service interphones , the CALLS panel, the mechanic call, PA and CIDS.
4 · Record and alert The CVR , the EVAC command, the cabin alert, the ELT and the ECAM memos.
Chapter 10 · Communications
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our plan. Part one is radio tuning: the overall architecture, then the radio management panel, how to change a frequency, why the SEL light comes on, the LOAD and AM functions, what happens when a panel fails, and the VHF, HF and SELCAL systems themselves. Part two is audio: the audio management unit and the audio control panel, with its transmission keys, reception knobs, call lights, push-to-talk switches and the audio switching selector. Part three covers internal communication: the flight, cabin and service interphones, the CALLS panel, calling the ground mechanic, and the passenger address with the cabin network behind it. Part four is about recording and alerting: the cockpit voice recorder, the evacuation command, the cabin alert, the emergency locator transmitter, and the green memos you may see on the E W D.
Overview
Where the equipment is Where the communication equipment sits Flight deck RMPs, ACPs, CALLS, RCDR, EVAC Avionics compartment VHF / HF transceivers, AMU VHF antenna on the fuselage HF coupler aft fuselage (optional HF) HF antenna in the fin Cockpit voice recorder aft section Internal: flight, cabin and service interphones, PA · External: VHF, HF (optional), SATCOM (some aircraft) Internal : flight, cabin and service interphones and the PA · External : VHF, HF (optional) and SATCOM (some aircraft), in voice or data
Chapter 10 · Communications
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us place the equipment on the aircraft. On the flight deck are the panels you touch: the radio and audio panels on the pedestal, and the CALLS, recorder and evacuation panels on the overhead. Below the cockpit, in the avionics compartment, are the VHF and HF transceivers and the audio management unit. Each VHF has an antenna on the fuselage. If the aircraft has HF, its coupler is in the aft fuselage and its antenna is in the vertical stabiliser, the fin. Right at the back, in the aft section, is the crash-proof cockpit voice recorder. The system as a whole gives internal communication between the pilots, the cabin crew, the ground crew and the passengers, and external communication by VHF, by HF, or on some aircraft by satellite, either in voice or as data.
Part 1 · Architecture
Three building blocks Three building blocks RMP 1 pedestal, captain RMP 2 pedestal, F/O RMP 3 overhead, optional Radio tuning frequency selection VHF 1 VHF 2 VHF 3 HF 1 HF 2 Transceivers avionics compartment RMP 3 talks to the radios through RMP 1 and RMP 2 AMU audio management unit ACP 1 captain ACP 2 F/O ACP 3 3rd occupant ACP 4 / 5 optional Audio integration select, transmit, listen audio RMPs tune the transceivers · transceivers in the avionics bay · the AMU and the ACPs route the audio
Chapter 10 · Communications
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The communication system has three building blocks. First, the radio tuning system: the radio management panels, or R M Ps. RMP 1 and RMP 2 are on the pedestal, one for each pilot, and some aircraft have a third RMP on the overhead panel. RMP 1 and RMP 2 are wired directly to every VHF and HF transceiver; RMP 3 reaches them through RMP 1 and RMP 2. The panels are linked, so a selection made on one is shown on the others. Second, the transceivers themselves: two VHFs, a third on some aircraft, and optionally two HFs. Third, the audio integrating system: the audio management unit, or A M U, and the audio control panels, the A C Ps, one per crew station. The RMP decides which frequency a radio is on. The ACP decides whether you are talking or listening on it.
Part 1 · Radio management panel
The RMP, key by key RMP 1 ACTIVE STBY/CRS 118.700 121.500 VHF1 VHF2 VHF3 LOAD HF1 SEL HF2 AM STBY NAV NAV VOR ILS GLS MLS ADF INNER ON OFF 1 2 3 4 5 6 7 8 9 10 1 ACTIVE / STBY-CRS windows 2 Transfer key: swaps the two 3 Radio com selection keys 4 Tuning knobs: outer = MHz, inner = decimals 5 AM pb (HF only; SSB is the default) 6 SEL indicator (amber) 7 NAV pb under a guard (backup nav tuning) 8 Radio navigation selection keys 9 ON / OFF switch 10 LOAD (CPDLC frequency, some aircraft)
Chapter 10 · Communications
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the radio management panel. At the top are two windows: ACTIVE, the frequency the radio is using now, and STBY slash CRS, a standby frequency you prepare. Between them is the transfer key, which swaps the two. Below are the radio communication keys: VHF 1, 2 and 3, and HF 1 and 2 on aircraft that have them. Press one and its small green monitor light comes on, and the windows show that radio. Then the AM key for HF, the amber SEL indicator, and the LOAD key used with controller-pilot datalink on some aircraft. On the right are the concentric tuning knobs and the ON OFF switch. Along the bottom, under a transparent guard, is the NAV key with the navigation keys; they are a backup for tuning the navaids, which you will meet in the navigation lesson. They do not change the communication radios.
Part 1 · Tuning
Changing a frequency Use your onside RMP; check it is ON Press the radio key (VHF 1 ): green light, both windows show that radio Set the STBY window: outer knob whole MHz, inner knob decimals Transfer key : STBY becomes ACTIVE, the radio retunesThe old frequency waits in STBY: one press to go back 1 · VHF 1 key pressed: green light on 118.700 121.500 ⇄ VHF1 VHF2 VHF3 SEL 2 · Knobs: outer 121 → 119, inner .500 → .250 118.700 119.250 ⇄ VHF1 VHF2 VHF3 SEL 3 · Transfer key: VHF 1 now on 119.250 119.250 118.700 ⇄ VHF1 VHF2 VHF3 SEL
Chapter 10 · Communications
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us tune a radio together. You are on 118.700 on VHF 1 and the controller says contact approach on 119.250. Normally you use the RMP on your own side. Make sure it is on, and press the VHF 1 key: its green light comes on, and the windows show VHF 1, active 118.700 and standby 121.500. Now turn the knobs. The outer knob changes the whole megahertz, so go from 121 down to 119. The inner knob changes the decimals, so go from .500 to .250. The standby window now reads 119.250. Finally press the transfer key. The two frequencies swap, the radio retunes to 119.250, and 118.700 waits in the standby window. If approach does not answer, one more press of the transfer key takes you straight back to the previous frequency.
Part 1 · The SEL light
Why SEL comes on Every radio "belongs" to one RMP: VHF 1 to RMP 1, VHF 2 to RMP 2 Three RMPs: VHF 3, HF 1, HF 2 belong to RMP 3. Two RMPs: VHF 3 and HF 1 to RMP 1, HF 2 to RMP 2 Tune a radio from another RMP: SEL amber on the RMPs It reminds you that an RMP is not on its own radio Cure: after tuning, reselect your own radio RMP 1: captain selects VHF 2 to tune it 122.800 119.400 ⇄ VHF1 VHF2 VHF3 SEL RMP 2 (F/O): SEL lit too 119.250 118.700 ⇄ VHF1 VHF2 VHF3 SEL Each RMP has its own radios (3 RMPs fitted): RMP 1 → VHF 1 · RMP 2 → VHF 2 · RMP 3 → VHF 3, HF 1, HF 2 Tune another one and SEL comes on amber. Fix: reselect your own radio (VHF 1 on RMP 1).
Chapter 10 · Communications
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The SEL light is an interview favourite. Each transceiver is normally associated with one RMP: VHF 1 with RMP 1, VHF 2 with RMP 2. With three RMPs fitted, VHF 3 and the HFs belong to RMP 3. With only two, VHF 3 and HF 1 go with RMP 1, and HF 2 with RMP 2. If you use an RMP to tune a radio that belongs to another panel, for example the captain selects VHF 2 on RMP 1, the amber SEL light comes on, on the RMPs. It is a reminder that at least one radio is not selected on its own panel. Why does it matter? Because each pilot reads his own VHF frequency on his own panel. So after any such tuning, the captain should press VHF 1 again on RMP 1. Both panels show their own radios, and the SEL lights go out.
Part 1 · Failures
RMP failure and emergency electrics The RMPs back each other up: any one RMP can control every radio .
One RMP fails It no longer controls its radio; the windows go blank and the green lights go out. Switch it OFF .
Another RMP takes over The remaining RMP tunes all the VHFs (and HFs). It will show SEL while it tunes another panel's radio.
EMER ELEC CONFIG Only RMP 1 works, and only VHF 1 . The captain's side keeps the voice link.
Exceptions RMP 3 works through RMP 1 and 2 even if they are OFF. With no RMP 3 and ACARS on VHF 3, VHF 3 is tuned for data by ACARS only.
Chapter 10 · Communications
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
What if an RMP fails? The failed panel can no longer control its radio: its windows go blank and its green lights go out. The action is simple: switch the failed RMP off. Because RMP 1 and RMP 2 are each connected to every transceiver, the remaining panel can control all the VHF and HF radios; you will see the SEL light while it tunes the other side's radio. Two exceptions are worth knowing. RMP 3, where fitted, works through RMP 1 and RMP 2 even when they are switched off. And if there is no RMP 3 and ACARS is connected to VHF 3, then VHF 3 can only be tuned, in data, by ACARS. Most important of all: in the emergency electrical configuration only RMP 1 works, and only VHF 1. The captain's RMP and VHF 1 are your voice link on batteries or the emergency generator.
Part 1 · The radios
VHF, HF and SELCAL System Fit and location Range / key facts VHF Two identical systems (a third on some aircraft); transceivers in the avionics compartment, antennas on the fuselage 118.0 – 136.975 MHz . Only VHF 1 in EMER ELEC CONFIGVHF 3 and ACARS Often used for datalink (ACARS) If ACARS is installed: no ATC voice on VHF 3 unless VHF 1 and 2 are inoperative (some aircraft) HF (optional) Two systems; transceivers in the avionics compartment, couplers in the aft fuselage , antenna in the fin 2.8 – 24 MHz ; SSB by default, AM by pbHF on the ground Voice mode not inhibited Keep people clear of the antenna ; never during refuelling or fuel transfer; limit to operational needs SELCAL Code selection panel in the avionics compartment Ground station calls the aircraft code: CALL flashes amber + buzzer; aural inhibited at take-off and landing
Chapter 10 · Communications
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the radios themselves. The VHFs: two identical systems, and some aircraft have a third. Each has a transceiver in the avionics compartment and an antenna on the fuselage. The range is 118.0 to 136.975 megahertz, and remember again that only VHF 1 works in the emergency electrical configuration. VHF 3 is often dedicated to datalink, ACARS; on some aircraft you must not use it for voice with ATC unless VHF 1 and VHF 2 are both unusable. HF is optional: two systems, with couplers in the aft fuselage and the antenna in the fin, from 2.8 to 24 megahertz. HF transmits a lot of power, so on the ground nobody may stand near the antenna, and you must never transmit during refuelling or fuel transfer. Finally SELCAL: when a ground station sends this aircraft's code, the crew gets a light and a buzzer, but the buzzer is inhibited during take-off and landing.
Part 1 · LOAD and AM
Two extra keys on the RMP LOAD (some aircraft): ATC sends CONTACT or MONITOR by datalink (CPDLC)White light above LOAD on every RMP ; press it to put the frequency in STBY/CRS Load it before you close the message; you can load it again on each RMP AM pb: only with an HF selected; default is SSB AM active: green light in the key RMP 1 ACTIVE STBY/CRS 118.700 132.350 VHF1 VHF2 VHF3 LOAD HF1 SEL HF2 AM STBY NAV NAV VOR ILS GLS MLS ADF INNER ON OFF LOAD (some aircraft) ATC sends CONTACT / MONITOR by CPDLC: white light above LOAD on every RMP; press it to put the frequency into STBY/CRS, then close the message. AM (HF only) HF works in single side-band by default; AM pb selects AM and shows a green light.
Chapter 10 · Communications
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two smaller keys complete the RMP. On aircraft with controller-pilot datalink, ATC can send a CONTACT or MONITOR message containing a new frequency. The datalink unit checks it and sends it to all the RMPs at once, and a white light comes on above the LOAD key. Press LOAD and the frequency drops into the standby window, ready for the transfer key. Do this before you close the datalink message. You can load it again on each RMP as often as you need, unless the standby window shows DATA. The AM key is for HF only. HF normally works in single side-band, S S B. If the station you are calling uses amplitude modulation, select the HF radio and press AM. A green light in the key shows that AM is active.
Part 1 · Interference
Keep the VHFs apart VHF 1 and 2, or VHF 2 and 3: interference possible if closer than 2 MHz VHF 1 and 3: closer than 6 MHz Example: 121.800 and 122.950 are only 1.15 MHz apart If it happens: use VHF 2 for ATC voice, or switch VHF 3 to VOICE Normally: onside RMP, then reselect your own radio Worked example: frequency spacing 118 120 122 124 126 128 130 132 134 136 MHz VHF 1 121.800 VHF 2 122.950 VHF 3 126.000 VHF 1 – VHF 2 1.15 MHz < 2 MHz interference possible VHF 2 – VHF 3 3.05 MHz ≥ 2 MHz clear VHF 1 – VHF 3 4.20 MHz < 6 MHz interference possible If it happens: use VHF 2 for ATC voice, or switch VHF 3 to VOICE.
Chapter 10 · Communications
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three VHF radios share one fuselage, so they can disturb each other when their frequencies are close. The rule of thumb: interference may occur if VHF 1 and VHF 2, or VHF 2 and VHF 3, are closer than 2 megahertz, or if VHF 1 and VHF 3 are closer than 6 megahertz. Let us check an example. VHF 1 is on tower, 121.800. VHF 2 is on 122.950. The difference is 1.15 megahertz, less than 2, so interference is possible. VHF 3 is on 126.000. From VHF 2 that is 3.05 megahertz, which is clear, but from VHF 1 it is 4.20, less than 6, so again interference is possible. If you do get interference, the advice is to use VHF 2 for voice with ATC, or to switch VHF 3 from data to voice.
Part 2 · Audio management
The audio management system One AMU (avionics compartment) and three ACPs ; a fourth and fifth on some aircraft At each station: boomset, headset jack, oxygen mask mike , hand mike A radio push-to-talk on each sidestick; two loudspeakers with their own volume An interphone jack at the ground power receptacle ; a SELCAL code panel If channel 1 or 2 fails: AUDIO SWITCHING to channel 3 AMU audio management unit ACP 1 · captain ACP 2 · F/O ACP 3 · 3rd occupant ACP 4, 5 · optional SELCAL code panel boomsets / headsets oxygen mask mikes (3) hand mikes sidestick PTT (2) loudspeakers (2) ground power jack AUDIO SWITCHING: third channel as backup
Chapter 10 · Communications
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The audio management system lets the crew use every radio, the interphones, the call systems and the passenger address. At its heart is the audio management unit, the A M U, in the avionics compartment. It serves three audio control panels, one for the captain, one for the first officer and one for the third occupant, with a fourth and fifth on some aircraft. Each station has its sockets: a headset jack, a boomset connector, a hand microphone, and an oxygen mask microphone; there are three mask microphones in the cockpit. Each sidestick has a radio push-to-talk switch, and there are two cockpit loudspeakers, each with its own volume knob. There is also an interphone jack at the ground power receptacle and a SELCAL code panel. If audio channel 1 or 2 fails, in the ACP or in its part of the AMU, the crew can switch to channel 3.
Part 2 · Audio control panel
The ACP: transmit on top, listen below ACP 1 SELCAL CALL CALL VHF1 CALL VHF2 CALL VHF3 CALL HF1 CALL HF2 MECH INT ATT CAB INT RAD ON VOICE RESET –PA– VOR1 VOR2 MKR LS MLS ADF1 ADF2 1 2 3 4 5 6 7 1 Transmission keys 3 green lines; CALL / MECH / ATT flash amber 2 Reception knobs out = listen (white light), turn = volume 3 RESET puts out CALL, MECH and ATT 4 ON VOICE filters VOR and ADF idents 5 INT/RAD switch INT, neutral, RAD (press and hold) 6 PA reception knob and transmission key 7 Nav reception knobs VOR, MKR, LS, MLS, ADF CALL (SELCAL), MECH (nose gear bay) and ATT (cabin) flash amber with a buzzer · MECH and ATT go out after 60 s if not reset · RESET puts them all out
Chapter 10 · Communications
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the audio control panel. The top row are transmission keys: VHF 1, 2 and 3, HF 1 and 2, INT for the flight interphone, and CAB for the cabin. Press one and three green lines light: that is where your microphone will transmit. The same keys flash amber call legends, with a buzzer: CALL for a SELCAL call on that radio, MECH on INT for the ground mechanic, and ATT on CAB for a cabin attendant. MECH and ATT go out after sixty seconds if not reset, and the RESET key puts them all out. Below each key is its reception knob: press and release it so it pops out, its white light comes on, and you hear that channel; turn it for volume, and push it in to disconnect. The middle row holds the INT RAD switch, ON VOICE, RESET and the PA controls, and the bottom knobs let you listen to the navaids. You can listen to many channels at once, but transmit on only one.
Part 2 · Push to talk
INT/RAD, sidestick and loudspeakers ACP INT/RAD : INT = mikes on interphone whatever key is selected; neutral = listen only; RAD (press and hold) = selected radio Sidestick selector: squeeze = RADIO ; spring-loaded neutral , mikes dead Sidestick RADIO has priority over INT ON VOICE : filters VOR and ADF idents (green ON)Loudspeaker knob: radio only, not aural alerts; turn down for feedback, but keep it audible Sidestick radio selector RADIO squeeze: RADIO release: neutral (mikes dead) RADIO beats INT on the INT/RAD switch INT RAD INT: mikes on interphone neutral: listen only RAD: press and hold, selected radio OFF LOUD SPKR radio audio only; not the aural alerts
Chapter 10 · Communications
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does the microphone get connected? On the ACP is the INT RAD switch. In the INT position, the boom and mask microphones transmit on the flight interphone whatever transmission key is selected; to hear the reply, the INT reception knob must be out. In the neutral position you just listen. Pressed to RAD and held, your microphone transmits on the radio selected on the ACP. The sidestick has the same function: squeeze the radio selector to transmit on the selected radio; release it and it springs back to neutral, microphones dead. If you squeeze RADIO on the sidestick while the INT RAD switch is at INT, the radio wins. Two more details: the ON VOICE key filters out the identification tones of VORs and ADFs; and the loudspeaker knob controls radio audio only, never the aural alerts. If it whistles, turn it down, but keep it loud enough.
Part 2 · Audio switching
Audio switching Use it if ACP 1 or ACP 2 (or its AMU channel) fails CAPT 3 : captain's headset and mikes work through ACP 3 F/O 3 : the same for the first officerThe third occupant loses his audio Not on NORM: AUDIO 3 XFRD green memo on the E/WD AUDIO SWITCHING NORM CAPT 3 F/O 3 E/WD memo AUDIO 3 XFRD NORM each pilot uses his own ACP and acoustic equipment CAPT 3 captain: own headset, mikes and PTT, through ACP 3 F/O 3 F/O: own headset, mikes and PTT, through ACP 3 The third occupant loses his audio access. Use: ACP 1 or ACP 2 (or its AMU channel) fails.
Chapter 10 · Communications
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
What if the captain's audio control panel fails? There is a rotary selector called AUDIO SWITCHING, normally at NORM, where each crew member uses his own equipment. Turn it to CAPT 3 and the captain keeps his own headset, microphones and push-to-talk, but works them through the third occupant's panel, ACP 3. F O 3 does the same for the first officer. There is a price: the third occupant loses access to the audio system, because his channel has been taken. Whenever the selector is not on NORM, the green memo AUDIO 3 X F R D, for transferred, appears on the E W D, so nobody forgets the selector is off normal. A typical interview question: the captain's ACP is dead, what do you do? Answer: audio switching to CAPT 3, and check AUDIO 3 XFRD.
Part 2 · Putting it together
How to talk to everyone To talk to… Reception (knob out) Transmission Then ATC on VHF 1 VHF 1 VHF 1 key (green lines) Sidestick RADIO or INT/RAD to RAD The other pilot or the ground mechanic (flight interphone) INT INT key PTT, or INT/RAD to RAD (INT position also transmits) Cabin crew or a service interphone jack CAB CAB key PTT, or INT/RAD to RAD The passengers (PA) PA PA key: press and hold Speak; no PTT needed. Or use the cockpit handset A SELCAL caller That radio That radio's key RESET the CALL light, answer Third ACP after a failure — — AUDIO SWITCHING to CAPT 3 or F/O 3
Chapter 10 · Communications
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put the panels together in a simple recipe. To call anyone, first make sure you can hear them, with the right reception knob out, then select where you will speak with the right transmission key, then press to talk. To talk to ATC on VHF 1: VHF 1 knob out, VHF 1 key, then squeeze the sidestick radio switch or press RAD. To talk to the ground mechanic or the other pilot on the flight interphone: INT knob out, INT key, then push-to-talk; or simply set the INT RAD switch to INT. For the cabin crew or a service interphone jack: CAB knob out, CAB key, push-to-talk. For the passengers: PA knob out, then press and hold the PA key and speak; no push-to-talk is needed, or you can use the cockpit handset instead. And after an ACP failure, use audio switching.
Part 3 · Flight interphone
Talking to the ground mechanic Hosted by the AMU : pilots with each other and with the ground crew Ground crew plug into the FLT INT jack on the external power panel, forward of the nose gear bay Crew: INT knob out, INT key, then PTT or RAD MECH pb on the overhead: blue COCKPIT CALL light and external horn at the noseMechanic's COCKPIT CALL pb: MECH flashes on the ACPs + buzzer External power panel (fwd of nose gear bay) FLT INT COCKPIT CALL COCKPIT CALL RESET ELT Talk ground crew plug into FLT INT; crew: INT knob out, INT key, PTT Cockpit → mechanic MECH pb (overhead CALLS): blue COCKPIT CALL light and an external horn; light stays on until RESET Mechanic → cockpit COCKPIT CALL pb: MECH flashes amber on the ACPs and a buzzer sounds; MECH out after 60 s if not reset
Chapter 10 · Communications
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
During pushback and engine start you talk to the ground mechanic on the flight interphone, which is part of the audio management unit. Pilots also use it to talk to each other, with boomsets, hand microphones or mask microphones. The mechanic plugs a headset into the FLT INT jack on the external power panel, just forward of the nose gear bay. In the cockpit, pull the INT reception knob out, press the INT key, then use push-to-talk or set the switch to RAD. To get the mechanic's attention, press the MECH pushbutton on the overhead CALLS panel: a blue COCKPIT CALL light comes on at the nose panel and an external horn sounds. The light stays on until the mechanic presses RESET. The other way round, the mechanic presses COCKPIT CALL: MECH flashes amber on your ACPs and a buzzer sounds.
Part 3 · Cabin interphone
The CALLS panel CALLS CABIN ALERT MECH ATTND ADV ON FWD MID EXIT PURS ALL AFT EMER CALL ON MECH calls the ground mechanic: blue COCKPIT CALL light and external horn at the nose FWD / MID / EXIT / AFT / PURS that area: 2 steady pink lights, CAPTAIN CALL on its AIP, high-low chime ALL every station responds as above EMER (guarded) all areas: pink lights flash, EMERGENCY CALL, high-low chime × 3 ATTND ADV ON light + green light at the attendant panel: take-off or landing imminent CABIN ALERT amber, some aircraft: the cabin has raised a discreet threat alert Not every aircraft has every button: MID, EXIT, PURS, ALL, ATTND ADV and CABIN ALERT vary. Cabin interphone: CAB key on the ACP. The system lets the flight crew call the attendants, and the attendants call each other.
Chapter 10 · Communications
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
To talk with the cabin crew you use the cabin interphone: CAB reception knob out, CAB transmission key, and boom, mask or hand microphone. To call them, use the CALLS panel on the overhead. Each area button, FWD, MID, EXIT, AFT or PURS for the purser, gives two steady pink lights on that area call panel, CAPTAIN CALL with a green light on its attendant indication panel, and a high-low chime in that area. ALL calls every station. The guarded EMER button is for an emergency: pink lights flash on every area call panel, EMERGENCY CALL appears on all attendant panels, and the high-low chime sounds three times through all loudspeakers. ATTND ADV, where fitted, lights a green light at the attendant panel to warn of imminent take-off or landing. Remember, the buttons fitted vary from aircraft to aircraft.
Part 3 · Calls from the cabin
When the cabin calls you CAPT key in the cabin: ATT flashes on all ACPs, one buzzerEMER CALL key: EMER ON flashes white, CALL flashes amber, ATT flashes, three buzzers Buzzers inhibited during take-off and landing The call system resets when the attendant hangs up Answer: CAB knob out, CAB key, push to talk Cabin → cockpit CALLS CABIN ALERT MECH ATTND ADV ON FWD MID EXIT PURS ALL AFT EMER CALL ON EMER CALL key in the cabin: ON flashes white, CALL flashes amber, ATT flashes on all ACPs, three buzzers SELCAL CALL CALL VHF1 CALL VHF2 CALL VHF3 CALL HF1 CALL HF2 MECH INT ATT CAB INT RAD ON VOICE RESET –PA– VOR1 VOR2 MKR LS MLS ADF1 ADF2 CAPT key in the cabin: ATT flashes on all ACPs, one buzzer; the cabin AIP shows CAPTAIN Buzzers are inhibited during take-off and landing; the lights still flash. The call resets when the attendant hangs up.
Chapter 10 · Communications
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the other direction. An attendant who needs the pilots presses the CAPT key on the handset. In the cockpit, ATT flashes on all the audio control panels and a buzzer sounds; in the cabin, CAPTAIN appears on that attendant indication panel. If it is urgent, the attendant presses EMER CALL. Now the EMER pushbutton on the CALLS panel flashes, its ON light white and its CALL light amber, ATT flashes on all the ACPs, and three buzzers sound one after another. Notice one thing: the buzzers are inhibited during take-off and landing, so the lights may be your only cue in those phases. To answer, pull out the CAB knob, press the CAB key and talk. The call system resets when the attendant hangs up the handset. In an interview, link EMER CALL to an emergency in the cabin, and expect to answer it at once.
Part 3 · Service interphone
Seven service interphone jacks 1 2 3 4 4 5 6 7 1 FWD electronic compartment 2 Electric compartment 3 Avionics compartment 4 Engine jacks (some aircraft) 5 Belly fairing panel 6 Aft fuselage 7 Near the APU bay Usable 10 s after landing with the gear down and locked; before that, or in flight: SVCE INT OVRD pb. Hosted by the CIDS · jacks usable 10 s after landing, gear locked down · otherwise SVCE INT OVRD pb · crew uses the CAB key
Chapter 10 · Communications
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Maintenance staff around the aircraft use the service interphone, which is part of the cabin network, the CIDS. There are seven jack positions: the forward electronic compartment, the electric compartment, the avionics compartment, the engines on some aircraft, the belly fairing, the aft fuselage and near the APU bay. They link the flight crew, the attendant stations and the jacks themselves. The jacks connect automatically ten seconds after landing, provided the landing gear is down and locked; that stops them being live in flight. If the gear is not locked down, for example during maintenance with the aircraft on jacks, pressing the SVCE INT OVRD pushbutton on the overhead makes them work anyway. From the cockpit you use the cabin channel: CAB knob out, CAB key, and push-to-talk.
Part 3 · Passenger address and CIDS
The PA and the cabin network PA knob out: you hear the PA, white lightPress and hold the PA key: three green lines; no PTT needed Or the cockpit handset (pedestal), with no ACP action PA IN USE / IFE / VIDEO lights and OBS AUDIO ENT on some aircraft CIDS : 2 directors (one active), FAP, DEUs type A and B; hosts the PA and service interphoneACP 1 SELCAL CALL CALL VHF1 CALL VHF2 CALL VHF3 CALL HF1 CALL HF2 MECH INT ATT CAB INT RAD ON VOICE RESET –PA– VOR1 VOR2 MKR LS MLS ADF1 ADF2 PA announcement from the ACP 1 · PA reception knob out: white light, set the volume 2 · press and HOLD the PA key: three green lines 3 · speak: no push-to-talk is needed or use the cockpit handset (no ACP action)
Chapter 10 · Communications
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Announcements to the passengers go through the passenger address, which the CIDS hosts. From your audio control panel, pull the PA reception knob out so you can hear the PA, then press and hold the PA transmission key: three green lines show, and you just speak. No push-to-talk is needed. Alternatively, pick up the cockpit handset at the bottom of the pedestal, which works with no action on the ACP. On some aircraft an overhead panel also has PA IN USE lights, and a switch that sends cockpit announcements to an entertainment channel. Behind all of this is the cabin intercommunication data system, the CIDS: two directors working in parallel, one active and one on standby, the flight attendant panel, and decoder encoder units along the cabin. Type A units serve the passengers, type B units serve the attendants. Beware: in the cabin, ACP means area call panel!
Part 4 · Cockpit voice recorder
What the CVR keeps Cockpit conversation, aural warnings , radio and interphone, datalink (later aircraft) PA only if PA reception is selected on at least one ACP Keeps the last 2 hours Area microphone behind the overhead; hot mike records the boom mikes without PTT Four-track , crash-proof, with an underwater locator beacon , in the aft sectionWhat the CVR records (last 2 h) cockpit conversations (area microphone) every aural warning radio audio, sent and received datalink messages (later aircraft) interphone between crew members PA announcements, if PA reception is selected on at least one ACP CVR 4 tracks · crash-proof ULB aft section of the fuselage "hot mike": voices from the boom mikes even without PTT
Chapter 10 · Communications
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The cockpit voice recorder captures the sound of the flight deck for accident investigators. It records direct conversation between the crew, every aural warning, the radio communications sent and received, the interphone between crew members, and on later aircraft the datalink messages too. PA announcements are recorded only if PA reception is selected on at least one audio control panel. It keeps only the last two hours. The sound comes from a remote area microphone behind the overhead panel, and from a hot mike function that takes each pilot's voice straight from the boom microphone, even when no push-to-talk is pressed. The recorder itself is a crash-proof four-track unit with an underwater locator beacon, installed in the aft section of the aircraft, where it is most likely to survive. The controls are on the RCDR panel on the overhead.
Part 4 · CVR logic
When the CVR records, and the RCDR panel When does the CVR record? A worked example automatic: engine running, flight, then 5 min after the last engine stops 5 min off GND CTL 0 · power on 25 · GND CTL pressed 40 · engine 1 start 60 · take-off 190 · landing 200 · last engine off 205 · recording stops Minutes after the aircraft is first powered. GND CTL pb: CVR and DFDR (and QAR) record on the ground; its ON light goes out after engine start. CVR ERASE (hold 2 s): on the ground with the parking brake on. CVR TEST: CVR on and parking brake on. RCDR GND CTL ON A U T O CVR ERASE CVR TEST Automatic: first 5 min after power-up · one engine running · in flight · until 5 min after the last engine shutdown . Manual: GND CTL .
Chapter 10 · Communications
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
When does the CVR record? Automatically in four cases: on the ground for the first five minutes after the aircraft's electrical network is powered; on the ground with at least one engine running; in flight; and on the ground until five minutes after the last engine is shut down. Follow the example. Power comes on at minute zero: five minutes of recording, then it stops. At minute twenty-five the crew presses GND CTL to record during preparation; its ON light shows. At minute forty engine one starts: the ON light goes out and recording continues automatically, through the flight, until five minutes after the last engine is shut down at minute two hundred. The same pushbutton starts the flight data recorders. CVR ERASE, held for two seconds, erases the recording only on the ground with the parking brake on. CVR TEST needs the CVR on and the parking brake on.
Part 4 · Evacuation
The EVAC command COMMAND (guarded): EVAC flashes red in the cockpit (horn on some aircraft); EVAC lights and evacuation tone in the cabinHORN SHUT OFF : silences the cockpit hornCAPT & PURS : cockpit or cabin can start the alertCAPT : cockpit only; a cabin CMD press sounds the cockpit horn for 3 s Cabin RESET silences the tone; COMMAND OFF stops the alert Cockpit EVAC panel EVAC COMMAND EVAC ON HORN SHUT OFF CAPT & PURS CAPT Cabin (FWD / AFT attendant panel) RESET EVAC CMD CAPT & PURS: cockpit or cabin can start it CAPT: cockpit only; a cabin CMD press sounds the cockpit horn for 3 s HORN SHUT OFF: cockpit horn RESET (cabin): evac tone COMMAND ON: EVAC flashes red in the cockpit (horn on some aircraft), EVAC lights flash at the FWD and AFT attendant panels, evacuation tone.
Chapter 10 · Communications
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the captain decides to evacuate, the EVAC panel on the overhead sends the signal. Lift the guard and press COMMAND. In the cockpit, the EVAC light flashes red and, on some aircraft, a horn sounds. In the cabin, EVAC lights flash on the forward and aft attendant panels and the evacuation tone sounds. Pressing COMMAND again, to off, stops the alert. HORN SHUT OFF silences the cockpit horn only. The third control is a switch with two positions. At CAPT and PURS, either the cockpit or the cabin can start the evacuation alert, using the CMD button on an attendant panel. At CAPT, only the cockpit can start it; if an attendant presses CMD, only the cockpit horn sounds, for three seconds, to tell the pilots the cabin wants to evacuate. In the cabin, RESET silences the evacuation tone.
Part 4 · Alerts and ELT
Cabin alert and the ELT Cabin to cockpit (some aircraft): attendant holds a button ≥ 1 s : continuous buzzer, red ALERT , amber CABIN ALERT Press ALERT to stop the buzzer and red light Cockpit to cabin : guarded pb: buzzer and red lights at each attendant areaELT ARMED : transmits on impact on 121.5, 243 and 406.025 MHz ; ON transmits now TEST/RESET : autotest, or stops an unwanted transmissionCabin alert (some aircraft) CAB ALERT (pedestal) ALERT Attendant holds a button ≥ 1 s: continuous buzzer, red ALERT, amber CABIN ALERT on CALLS (time limited). Press ALERT: buzzer and red light stop. Reverse: guarded cockpit pb → cabin buzzer + red lights. Emergency locator transmitter ELT ON ARMED TEST/RESET ON TEST ON transmits now ARMED transmits on impact: 121.5, 243 and 406.025 MHz TEST/RESET autotest; also stops an unwanted transmission Amber ON TEST / ELT lights: transmitting or autotest. ELT light: on the external power panel.
Chapter 10 · Communications
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more alert systems. On some aircraft, the cabin crew can rapidly and discreetly warn the pilots of a threat in the cabin, such as an attempt to force the cockpit door. An attendant holds an alert button for at least one second. In the cockpit a buzzer sounds continuously, a red ALERT light comes on in the CAB ALERT pushbutton on the pedestal, and an amber CABIN ALERT light comes on on the CALLS panel for a limited time. Pressing ALERT stops the buzzer and the red light. The pilots can alert the cabin too, with a guarded pushbutton that sounds a buzzer and lights red lights in each attendant area. Finally the emergency locator transmitter. Normally its selector is ARMED: on impact it transmits on 121.5, 243 and 406.025 megahertz. ON makes it transmit immediately. TEST RESET starts a self-test, or stops a transmission triggered by a hard landing. Amber lights show when it is transmitting.
Part 4 · ECAM
Communication memos ACARS CALL : ground wants a VHF voice contact; ACARS MSG : message received (pulse 60 s)ACARS STBY : datalink lost, or initialisation data neededVHF 3 VOICE : VHF 3 in voice, ACARS interruptedHF VOICE : both HFs in voice (flashes 10 s)AUDIO 3 XFRD : selector not on NORM; SATCOM ALERT , TEL … CALL on some aircraftE/WD · memo area (green) ACARS CALL ACARS MSG ACARS STBY VHF 3 VOICE HF VOICE AUDIO 3 XFRD SATCOM ALERT pulses 60 s, then steady pulses 60 s, then steady datalink lost / init needed VHF 3 voice: ACARS cut both HFs in voice; flash 10 s selector not on NORM priority below 4 (some a/c) Memos are green: information, not a failure. Some aircraft also show TEL EMER / ATC / CPNY CALL for a SATCOM telephone call.
Chapter 10 · Communications
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
The communication system adds a few green memos to the E W D. Green means information, not a failure. ACARS CALL means the ground has sent a message asking you to call them on VHF voice; ACARS MSG means a message has arrived. Both pulse for sixty seconds, then stay steady. ACARS STBY means datalink with the ground has been lost, or that the system needs you to enter initialisation data. VHF 3 VOICE tells you VHF 3 is in voice mode, so ACARS is interrupted. HF VOICE means both HFs are in voice mode, and it flashes for ten seconds first. AUDIO 3 XFRD, as we saw, means the audio switching selector is not at NORM. On aircraft with satellite communication you may also see SATCOM ALERT, for a message with a priority below four, or a TEL CALL memo for an incoming emergency, ATC or company telephone call.
Summary
Communications on one page RMP Onside RMP, outer knob MHz, inner decimals, transfer key. SEL : a radio tuned from another RMP. Any RMP tunes every radio; EMER ELEC: RMP 1 and VHF 1 only .
Radios VHF 118.0–136.975 MHz ; HF optional 2.8–24 MHz , not during refuelling. Interference: 2 MHz (1–2, 2–3), 6 MHz (1–3). SELCAL aural inhibited at T/O and landing.
ACP Knob out = listen, key = transmit. CALL / MECH / ATT flash amber, MECH and ATT out after 60 s. Sidestick RADIO beats INT. AUDIO 3 XFRD when not NORM.
Interphones and PA Flight interphone: AMU, FLT INT jack at the nose. Service interphone: CIDS, 7 jacks, 10 s after landing gear locked, else SVCE INT OVRD . PA: hold the key, no PTT.
CVR Last 2 h , four tracks, aft. Records first 5 min after power-up, engine running, flight, until 5 min after the last engine. GND CTL; ERASE 2 s on ground, parking brake on.
Alerts EVAC COMMAND; CAPT & PURS or CAPT (cabin CMD: horn 3 s). Cabin alert ≥ 1 s. ELT ARMED: 121.5 / 243 / 406.025 MHz on impact.
Chapter 10 · Communications
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us wrap up. The RMP: use your own, outer knob for megahertz, inner for decimals, then transfer. SEL means a radio is being tuned from another panel; reselect your own radio. Any RMP can tune any radio, but in the emergency electrical configuration only RMP 1 and VHF 1 survive. The radios: VHF from 118 to 136.975, optional HF from 2.8 to 24, never during refuelling. The ACP: knob out to listen, key to transmit, call lights flash amber, and audio switching to channel 3 gives the AUDIO 3 XFRD memo. Flight interphone to the nose, service interphone jacks ten seconds after landing or with the override, PA with the key held. The CVR keeps two hours and records from power-up, with engines running and in flight, until five minutes after shutdown. And finally the alerts: EVAC, the cabin alert and the ELT.