A320 Aircraft Systems · Chapter 21
ECAM Logic, Warnings and Recorders How the ECAM decides what to show you: warning levels, flight phases, memos, system pages, STATUS, the control panel and the recorders.
84.6 84.6 N1 % 612 615 EGT °C 94.1 N2 94.0 1150 FF 1160 KG/H FOB : 13600 S F HYD B RSVR OVHT -BLUE ELEC PUMP........OFF STATUS TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG MAX SPD.............250 / .85 APPR PROC DUAL HYD LO PR -IF BLUE OVHT OUT: -BLUE ELEC PUMP.....ON -L/G...........GRVTY EXTN -LDG SPD INCREM.....10KT -LDG DIST PROC.....APPLY CAT 1 ONLY SLATS SLOW INOP SYS G+B HYD CAT 3 G RSVR L+R AIL SPLR 1+3+5 L ELEV AP 1+2 REVERSER 1 NORM BRK NW STEER MAINTENANCE APU AIR COND CANCELLED CAUTION NAV IR 2 FAULT WARNINGS · MEMOS · STATUS © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the ECAM, the electronic centralised aircraft monitor. In the last lesson we met its two screens as displays. Now we learn how it thinks. When does a failure deserve a red warning and a chime, and when only an amber line with no sound? Why do some alerts wait until you are safely airborne? Which system page appears by itself in each phase of flight, and what does the STATUS page tell you before an approach? We will walk through a real failure from the first chime to the last press of CLR, then learn every key on the ECAM control panel. We finish with the flight data recorders. The ECAM is how the aircraft talks to you, so learning its language well pays off on every simulator check.
ATA 31
Our route through the ECAM 84.6 84.6 N1 % 612 615 EGT °C 94.1 N2 94.0 1150 FF 1160 KG/H FOB : 13600 S F HYD B RSVR OVHT -BLUE ELEC PUMP.......OFF ECAM UPPER DISPLAY LOWER DISPLAY OFF BRT OFF BRT T.O CONFIG EMER CANC ENG BLEED PRESS ELEC HYD FUEL APU COND DOOR WHEEL F/CTL ALL CLR STS RCL CLR STATUS TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG MAX SPD.............250 / .85 APPR PROC DUAL HYD LO PR -IF BLUE OVHT OUT: -BLUE ELEC PUMP.....ON -L/G...........GRVTY EXTN -LDG SPD INCREM.....10KT -LDG DIST PROC.....APPLY CAT 1 ONLY SLATS SLOW INOP SYS G+B HYD CAT 3 G RSVR L+R AIL SPLR 1+3+5 L ELEV AP 1+2 REVERSER 1 NORM BRK NW STEER MAINTENANCE APU AIR COND CANCELLED CAUTION NAV IR 2 FAULT Principles Modes, colours, warning levels, failure types, attention getters, aurals.
E/WD Message areas, flight phases, inhibition, memos, T.O CONFIG.
SD System pages by phase, advisories, STATUS and permanent data.
Using it A failure from chime to CLR, the control panel, OEB, recorders.
Chapter 21 · ECAM Logic, Warnings and Recorders
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our plan for the ECAM lesson. We begin with principles: the four operating modes, the colour code, the three levels of warning and caution, the types of failure, and the lights and sounds that get your attention. Then the upper screen, the engine and warning display: where messages appear, how the ten flight phases inhibit alerts at critical moments, the take-off and landing memos and the take-off configuration check. Then the lower screen: which system page appears when, advisories, the STATUS page and the permanent data line. Finally we use it: a complete hydraulic failure from the first chime to the last press of CLR, every key on the ECAM control panel, the OEB reminder, and the flight data recorders. The ECAM procedures themselves are trained in the simulator, but the logic you learn here explains everything you will see there.
ECAM principles
Information when it is needed Normal mode : memos and the system page for the flight phase Failure mode : the abnormal procedure on the E/WD, the failed system on the SDAdvisory mode : a drifting parameter calls its page; the value pulses Manual mode : any page via the ECAM control panel Most alerts are inhibited at take-off and landing SEAT BELTS NO SMOKING DOOR NORMAL memos on the E/WD SD page for the flight phase HYD B RSVR OVHT -BLUE PUMP...OFF HYD FAILURE warning or caution with actions SD page of the failed system ADV ELEC 153 °C ADVISORY drifting parameter: SD page called the value pulses green SEAT BELTS FUEL MANUAL crew calls any SD page with the ECP keys
Chapter 21 · ECAM Logic, Warnings and Recorders
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The whole idea of the ECAM is to show the crew what they need, when they need it. It works in four modes. In normal mode, nothing is wrong: the upper screen shows memos and the lower screen shows the system page that suits the present flight phase. In failure mode, the upper screen shows the warning or caution with the actions to take, and the lower screen shows the diagram of the failed system. In advisory mode, nothing has failed yet, but a parameter is drifting out of its normal range, so its page is called and the value pulses in green. And in manual mode, you choose any page yourself with the ECAM control panel. One more principle: most warnings and cautions are inhibited during take-off and landing, because most system failures do not affect your ability to complete them.
ECAM principles
The ECAM colour code Red : immediate action requiredAmber : be aware, no immediate actionGreen : normal operationWhite : titles and remarks that guide youBlue : actions to carry out, or limitations; magenta : special messages such as inhibitionsRED immediate action ENG 1 FIRE AMBER be aware, no immediate action HYD G SYS LO PR GREEN normal operation SEAT BELTS WHITE titles and remarks STATUS / INOP SYS BLUE (cyan) actions to do, limitations -BLUE ELEC PUMP......OFF MAGENTA special messages, e.g. inhibition T.O INHIBIT
Chapter 21 · ECAM Logic, Warnings and Recorders
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ECAM uses colour to tell you how important something is before you even read it. Red means the configuration or failure needs immediate action, like an engine fire. Amber means you should be aware of it, but no immediate action is required, like a hydraulic system low pressure. Green means a system is operating normally. White is used for titles and remarks that guide you through a procedure. Blue, which you will often hear called cyan, shows actions to be carried out, or limitations. Magenta is kept for particular messages, such as the take-off and landing inhibition memos. In the cockpit this becomes automatic: your eye goes to red first, then amber, and blue tells you what to do with your hands.
ECAM principles
Warning and caution levels Level Meaning Aural Visual Level 3 (red) immediate action: dangerous configuration, flight limit (stall, overspeed), or safety-critical failure (engine fire, excess cabin altitude) continuous repetitive chime, specific sound or voice MASTER WARN flashing, red message, SD page (1) Level 2 (amber) no immediate action, but act without delay (e.g. HYD G SYS LO PR) single chime MASTER CAUT steady, amber message, SD page (1) Level 1 (amber) monitoring: loss of redundancy (e.g. FCDC fault) none amber message, usually no procedure Advisory parameter drifting out of range none SD page called, value pulses green Memo functions used temporarily none green, amber or magenta on the E/WD
(1) except in some cases. Priority: level 3 over level 2 over level 1; the FWC applies it.
Chapter 21 · ECAM Logic, Warnings and Recorders
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every alert belongs to a level, and the level decides the signals you get. Level three is the red warning: the aircraft is in a dangerous configuration or at a flight limit, such as a stall or an overspeed, or a failure affects flight safety, such as an engine fire or excessive cabin altitude. You get a continuous repetitive chime or a specific sound or voice, the MASTER WARN lights flash red, a red message appears and the system page is called. Level two is the amber caution: no immediate action, but deal with it without delay, for example a green hydraulic low pressure. A single chime, steady MASTER CAUT, an amber message and the page. Level one is an amber caution for monitoring only, for example an FCDC fault: no chime, no master light, and usually no procedure. Advisories and memos have no sound at all.
ECAM principles
Independent, primary and secondary failures Independent : affects one system onlyPrimary : costs the aircraft other systems; shown with a boxed titleSecondary : a system lost because of a primary failure; shown with a * Secondary failures appear in the right column of the E/WD In ELEC EMER CONFIG , secondary failures are inhibited HYD B SYS LO PR -BLUE ELEC PUMP.......OFF * F/CTL Lower part of the E/WD 1 Primary failure: boxed title 1 2 Action line: blue; clears when done 2 3 Secondary failure: * before the title 3 Independent failure: affects one system, no consequence for the others
Chapter 21 · ECAM Logic, Warnings and Recorders
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ECAM sorts failures into three types. An independent failure affects one system or item of equipment and does not degrade any other. A primary failure is one that costs the aircraft other systems as well; the ECAM draws its title inside a box. A secondary failure is the loss of a system caused by a primary failure; it is written in the right-hand column with a star in front of the title. In our example the blue hydraulic system has lost its pressure, which is the boxed primary failure, and because some flight control actuators use blue, star F slash CTL appears as a secondary failure. If there are too many to show, an overflow arrow appears. And remember one exception: in the electrical emergency configuration the secondary failures are inhibited, so the screen is not flooded.
Attention getters
MASTER WARN and MASTER CAUT MASTER WARN flashes red: level 3, with an aural warningMASTER CAUT steady amber: level 2, with a single chimeLights go out: press the light, CLR , EMER CANC , or the condition ends Aural stops: press MASTER WARN, EMER CANC , or the condition ends Not for some red warnings: overspeed and stall continue MASTER WARN MASTER CAUT flashes red level 3 warning steady amber level 2 caution One set in front of each pilot Loudspeaker: chimes and voices
Chapter 21 · ECAM Logic, Warnings and Recorders
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flight warning computers drive a set of attention getters in front of each pilot, under the glareshield. For a level three warning the MASTER WARN light flashes red, together with the aural warning. For a level two caution the MASTER CAUT light comes on steady amber with a single chime. The lights go out when a pilot presses the light, when the condition is over, when CLR is pressed, or when EMER CANC is pressed. The aural warning stops when a pilot presses MASTER WARN, when the condition is over, or with EMER CANC. But there are important exceptions: for some red warnings, such as overspeed and stall, pressing the light or CLR does not silence them, because the only cure is to fix the flight condition. The loudspeakers give the aural alerts even if they are switched off.
Audio indicators
Chimes, sounds and how to stop them Sound Meaning Duration Cancelled by Continuous repetitive chime red warning permanent MASTER WARN Single chime amber caution 0.5 s - Cavalry charge AP off: take-over pb / failure 1.5 s / permanent 2nd take-over push / MASTER WARN or take-over Triple click landing capability downgrade, some reversions 0.5 s - Cricket + "STALL" stall permanent nil C chord altitude alert 1.5 s or permanent new altitude or MASTER WARN Buzzer cabin / emer cabin / mech call 3 s / 3 s x3 / while pressed MECH: MASTER CAUT Continuous buzzer SELCAL call permanent ACP RESET or MASTER CAUT
EMER CANC cancels any audio indicator; MASTER WARN cancels any, except OVERSPEED and L/G NOT DOWN.
Chapter 21 · ECAM Logic, Warnings and Recorders
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
You must recognise each sound without looking. The continuous repetitive chime is a red warning and lasts until you press MASTER WARN. The single chime, half a second long, is an amber caution. The cavalry charge means the autopilot has disconnected: a short one and a half seconds if you used the take-over button, and permanent if it dropped out through a failure, until you press MASTER WARN or take-over. A triple click signals a landing capability downgrade or some mode reversions. A cricket with the voice STALL is the stall warning. The C chord is the altitude alert. Buzzers belong to cabin and mechanic calls, and a continuous buzzer to a SELCAL call. As a rule, EMER CANC cancels any audio, and MASTER WARN cancels any audio except the overspeed and landing gear not down warnings.
Audio indicators
Synthetic voice messages Voice Meaning Duration Stops when "RETARD" levers not at IDLE or REVERSE for landing once at 20 ft (10 ft autoland + A/THR), then on levers at IDLE or REV "RETARD, RETARD" one lever above IDLE after touchdown, other at IDLE/REV permanent if triggered above 40 kt levers at IDLE or REV "PRIORITY LEFT/RIGHT" sidestick take-over pb pressed 1 s - "DUAL INPUT" both sidesticks moved together every 5 s one stick deactivated "SPEED, SPEED, SPEED" thrust too low to regain the flight path with pitch every 5 s thrust increased "STOP RUDDER INPUT" rudder inputs in cruise at high speed at least twice - "PITCH, PITCH" excessive pitch in flare (some aircraft) once -
Also: "WINDSHEAR" (3 times), W/S AHEAD voices, radio height callouts below 2 500 ft, GPWS and TCAS voices.
Chapter 21 · ECAM Logic, Warnings and Recorders
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many alerts are spoken by a synthetic voice. RETARD is heard once at twenty feet, or ten feet in an autoland with autothrust, and repeats until all thrust levers are at idle or reverse. RETARD RETARD means one lever was left above idle after touchdown while the other is at idle or reverse; if triggered above forty knots it continues until both are back. PRIORITY LEFT or PRIORITY RIGHT is announced for one second when a pilot presses the sidestick take-over button. DUAL INPUT repeats every five seconds while both sidesticks are moved together. SPEED SPEED SPEED means the thrust is too low to recover a positive flight path with pitch alone, so add thrust. STOP RUDDER INPUT warns of inappropriate rudder inputs at high speed in cruise. And windshear has its own voices: WINDSHEAR repeated three times, and the predictive W S AHEAD messages.
Engine/warning display
Where messages appear on the E/WD 84.6 84.6 N1 % 612 615 EGT °C 94.1 N2 94.0 1150 FF 1160 KG/H FOB : 13600 S F ELEC AC BUS 1 FAULT -BLOWER............OVRD -AC ESS FEED........ALTN HYD G ENG 1 PUMP LO PR -ENG 1 PUMP.........OFF * F/CTL * BLEED LAND ASAP 1 Engine primary parameters N1, EGT, N2, fuel flow 2 Bottom left primary or independent failures and actions, or memos 3 Overflow arrow more lines: press CLR 4 Fuel on board, slats/flaps and feedback messages 5 Bottom right secondary failures (*), memos, AP OFF, LAND ASAP, overflow titles The title and actions appear at once unless a flight-phase inhibition is active; most action lines clear as they are done.
Chapter 21 · ECAM Logic, Warnings and Recorders
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Look at the lower part of the engine and warning display, below the engine parameters. It has two areas. The bottom left shows primary or independent warnings and cautions with their action lines, or memos when nothing is wrong. The bottom right shows secondary failures, memos, special lines such as AP OFF or LAND ASAP, and the titles of systems affected by a failure when the left side overflows. As soon as the flight warning computer detects a failure, and if no flight phase inhibition is active, the title and the actions appear. Each action line clears automatically when you complete it, although a few stay on the screen even after the action. When there are more lines than the space allows, a green arrow at the bottom points down; press CLR on the ECAM control panel to scroll to the next messages.
Flight warning computer
The ten flight phases ELEC PWR 1ST ENG STARTED 1ST ENG T.O PWR 80 kt LIFT OFF 1 500 ft 800 ft TOUCHDOWN 80 kt 2ND ENG SHUTDOWN 5 MIN AFTER 1 2 3 4 5 6 7 8 9 10 T.O INHIBIT (3, 4, 5) LDG INHIBIT (7, 8) These FWC phases are independent of the FMGC flight phases.
Chapter 21 · ECAM Logic, Warnings and Recorders
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flight warning computer divides every flight into ten phases. Phase one starts with electrical power. Phase two begins when the first engine is started, phase three when the first engine reaches take-off power, and phase four at eighty knots. Phase five is from lift-off to one thousand five hundred feet. Phase six is the rest of the flight, until eight hundred feet on the approach. Phase seven runs from eight hundred feet to touchdown, phase eight from touchdown to eighty knots, phase nine from eighty knots to the second engine shutdown, and phase ten lasts five minutes after that, before the cycle returns to phase one. Notice the magenta bands: T.O INHIBIT covers phases three, four and five, and LDG INHIBIT covers phases seven and eight. Do not confuse these phases with the flight phases of the FMGC, which are quite separate.
Flight warning computer
Flight phase inhibition Inhibition avoids distracting the crew at high workload Magenta T.O INHIBIT memo in phases 3, 4, 5 ; LDG INHIBIT in 7, 8 A failure before the inhibited phase stays displayed through it A failure during it is held until the next phase where it is allowed Pressing RCL lifts the inhibition until the next flight phase Failure appearance versus an inhibited phase 1 2 3 4 5 inhibited phase a b a b a Failure in phase 1: displayed at once, and it stays on through phase 2 while the failure lasts. b Failure in phase 2: held back, then displayed when phase 3 starts (not inhibited for it). RCL for more than 3 s: shows cancelled alerts; any RCL press also lifts flight-phase inhibition until the next phase
Chapter 21 · ECAM Logic, Warnings and Recorders
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Inhibition is a deliberate design choice. During take-off and landing the workload is high, and most system failures do not affect your ability to complete them, so the FWC holds back many alerts and shows a magenta T.O INHIBIT or LDG INHIBIT memo instead. Look at the example. In case a, the failure happens in phase one; it is displayed at once and simply stays on through phase two, even though phase two is inhibited for that alert. In case b, the same failure happens during phase two; this time it is held back, and only appears when the aircraft enters phase three, where it is no longer inhibited. Then it remains as long as the failure exists. One useful trick: pressing RCL on the ECAM control panel lifts the flight phase inhibition until the next phase, so any new alert will be shown at once.
Engine/warning display
The T.O and LDG memos T.O AUTO BRK MAX SIGNS ON CABIN CHECK SPLRS ARM FLAPS T.O T.O CONFIG TEST LDG LDG GEAR DN SIGNS ON CABIN CHECK SPLRS ARM FLAPS FULL T.O memo appears 2 min after the second engine start, or when T.O CONFIG is pressed with at least one engine running; gone at T.O power Item names green; dots and value blue until done, then the value turns green and the dots go T.O CONFIG TEST becomes T.O CONFIG NORMAL if the check passes LDG memo appears below 2 000 ft (RA); gone after touchdown at 80 kt FLAPS shows CONF 3 instead of FULL in alternate or direct law, or with the GPWS LDG FLAP 3 pb ON After a go-around below 2 200 ft RA: memo only below 800 ft Memos list functions used temporarily in normal operation: normally green, amber in some abnormal cases.
Chapter 21 · ECAM Logic, Warnings and Recorders
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Memos list systems that are being used temporarily in normal operation, such as seat belt signs or engine anti ice. They are normally green and occasionally amber. Two memos are special checklists. The take-off memo appears two minutes after the second engine start, or when you press T.O CONFIG with at least one engine running, and it disappears when take-off power is set. It lists autobrake max, signs on, cabin check, spoilers armed, flaps for take-off and the take-off configuration test. Each item name is green; the dots and the target value stay blue until the action is done, and then the dots go and the value turns green. When the test passes, it reads T.O CONFIG NORMAL. The landing memo appears below two thousand feet and disappears after touchdown at eighty knots. It shows CONF 3 instead of FULL in alternate or direct law, or with LDG FLAP 3 selected.
Take-off configuration
T.O CONFIG test and take-off power Warning or caution T.O CONFIG test Take-off power CONFIG RUD TRIM, PITCH TRIM, FLAPS, SLATS, SPD BRK; L or R SIDESTICK FAULT (red) triggered triggered F/CTL PITCH TRIM/MCDU/CG DISAGREE, F/CTL FLAP/MCDU DISAGREE (amber) triggered triggered DOOR, BRAKES HOT (amber) triggered triggered FUEL L(R) TK PUMP 1+2 LO PR, HYD ENG PUMP LO PR, HYD SYS LO PR (amber) triggered not triggered ELEC IDG DISCONNECTED, GEN FAULT, GEN OFF (amber) only if both GENs are inop not triggered CONFIG PARK BRK ON (red) not triggered triggered ENG THR LEVERS NOT SET (amber) not triggered triggered
F/CTL FLAP/MCDU DISAGREE is inhibited when CONFIG FLAPS NOT IN T.O CONFIG is present.
Chapter 21 · ECAM Logic, Warnings and Recorders
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before take-off the crew presses the T.O CONFIG key, which simulates the application of take-off power and checks the configuration. Here is what each check catches. The red CONFIG warnings for rudder trim, pitch trim, flaps, slats, speedbrakes not retracted and a sidestick fault are triggered both by the test and by real take-off power, and so are the amber disagree cautions, DOOR and BRAKES HOT. Fuel pump and hydraulic low pressures are caught by the test only. The electrical generator cautions appear in the test only if both generators are inoperative. And two items work the other way round: the parking brake on, and thrust levers not set, are not triggered by the test, but they are triggered when you actually apply take-off power. That is an exam favourite: a passed T.O CONFIG test does not prove the parking brake is released.
System display
Twelve system pages: manual and automatic 12 pages, from ENGINE to CRUISE ; any except CRUISE by hand The key lights when pushed; a second push returns to the automatic page Failure : the page of the failed system appears automaticallyAdvisory : the page appears and the drifting value pulses green (inhibited in some phases)A failure or advisory page replaces a manually selected page ECAM UPPER DISPLAY LOWER DISPLAY OFF BRT OFF BRT T.O CONFIG EMER CANC ENG BLEED PRESS ELEC HYD FUEL APU COND DOOR WHEEL F/CTL ALL CLR STS RCL CLR FUEL lit: page selected manually ENGINE · BLEED · CAB PRESS · ELEC HYD · FUEL · APU · COND DOOR/OXY · WHEEL · F/CTL · CRUISE CRUISE cannot be called manually Second push: back to the flight-phase or warning page A failure or advisory page replaces a manual page
Chapter 21 · ECAM Logic, Warnings and Recorders
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The system display can show twelve system pages: engine, bleed, cabin pressure, electrical, hydraulic, fuel, APU, air conditioning, doors and oxygen, wheel, flight controls and cruise. You can call any of them, except CRUISE, at any time with its key on the ECAM control panel, and the key lights up. Pushing it a second time returns to the page for the flight phase or the current warning. The ECAM also calls pages by itself. When a failure triggers a warning or caution, the page of that system appears at once. In advisory mode, when a parameter drifts out of its normal range, the page appears and the green value pulses; this mode is inhibited in some flight phases. A failure or advisory page always replaces a page you called manually. With only one ECAM screen working, an advisory makes an ADV message appear and the related key flash instead.
System display
The automatic page for each flight phase 1 2 3 4 5 6 7 8 9 10 DOOR WHEEL ENG CRUISE WHEEL DOOR F/CTL for 20 s on stick or rudder input from 1st engine T.O power phase 6: CRUISE when S/F up and no T.O power, else after 1 min L/G down and below 15 500 ft after 2nd engine shutdown ELEC PWR 1ST ENG T.O PWR LIFT OFF TOUCHDOWN 2ND ENG SHUTDOWN Also automatic: APU page with APU MASTER SW ON; ENGINE page during an engine start or CRANK.
Chapter 21 · ECAM Logic, Warnings and Recorders
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
When no other mode is active, the SD shows the page that suits the flight phase. In phase one you see the DOOR page. After the first engine start, phase two, the WHEEL page appears, and it is replaced by the flight controls page for twenty seconds if either pilot moves a sidestick more than three degrees or the rudder pedals more than twenty two degrees, which is how you do the flight control check. From take-off power the ENGINE page is shown. In phase six, the CRUISE page replaces it when the slats and flaps are up and take-off power is no longer set, and in any case after one minute. Once the landing gear is down below fifteen thousand five hundred feet you get the WHEEL page again, and after the second engine shutdown the DOOR page. The APU and ENGINE pages also appear automatically during an APU or engine start.
System display
The STATUS page Operational summary: limitations , approach procedures , corrections , information, INOP SYS Called with STS ; NORMAL for 3 s if empty; cleared by CLR or STS Appears by itself if not empty: when the last alert is cleared , or at CONF 1 for approach STS reminder on the E/WD while the page holds more than cancelled cautions or maintenanceMAINTENANCE status only on the ground, before start or after shutdownSTATUS TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG MAX SPD.............250 / .85 APPR PROC DUAL HYD LO PR -IF BLUE OVHT OUT: -BLUE ELEC PUMP.....ON -L/G...........GRVTY EXTN -LDG SPD INCREM.....10KT -LDG DIST PROC.....APPLY CAT 1 ONLY SLATS SLOW INOP SYS G+B HYD CAT 3 G RSVR L+R AIL SPLR 1+3+5 L ELEV AP 1+2 REVERSER 1 NORM BRK NW STEER MAINTENANCE APU AIR COND CANCELLED CAUTION NAV IR 2 FAULT limitations, procedures approach proc., INOP SYS information titles, cancelled caution, maintenance
Chapter 21 · ECAM Logic, Warnings and Recorders
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The STATUS page is the operational summary of the aircraft after a failure. Its blocks are separated by blank lines. At the top, in blue, are limitations such as a maximum speed or flight level. Then the approach procedure, with a white title, and blue corrections for landing, such as a landing speed increment. Green lines give information, such as CAT 1 ONLY. On the right, amber lists the inoperative systems, and in white below are cancelled cautions and maintenance status. You call the page with the STS key; if there is nothing to show it says NORMAL for three seconds. It also appears by itself when it is not empty and you clear the last alert, or when you select flap one for the approach, which is a good reminder to review it. While it holds anything more than cancelled cautions or maintenance items, an STS reminder stays on the E/WD.
System display
Permanent data, crosses and dashes TAT and SAT in green; ISA deviation in standard altitude modeG LOAD amber above 1.4 g or below 0.7 g for 2 s; held 5 s; not in phases 1, 2, 3, 9, 10Feedback messages (CHECK SD...) have priority over G LOAD UTC from the cockpit clock; GW after the first engine startAmber XX : value not available; amber dashes: accuracy degraded TAT -28 °C SAT -49 °C ISA +8 14 H 32 GW 68200 KG TAT +12 °C SAT +9 °C 09 H 05 G LOAD 1.5 GW 61400 KG Cruise, standard altitude: ISA deviation shown G LOAD amber: above 1.4 g or below 0.7 g for 2 s TAT, SAT (and ISA) · UTC · gross weight, all green stays 5 s after the event; not shown in phases 1, 2, 3, 9, 10 XX 68 2- - GW - - - - - value not available accuracy degraded on ground, no GW yet GW appears once the first engine is started
Chapter 21 · ECAM Logic, Warnings and Recorders
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Along the bottom of every SD page runs the permanent data line. On the left, total and static air temperature in green, and when flying on standard altimeter setting with a valid SAT, the deviation from ISA. In the centre is UTC, synchronised with the cockpit clock. Above it the ECAM can show the load factor in amber, when it exceeds one point four g or drops below nought point seven g for more than two seconds; it stays for five seconds after the event and is not shown in phases one, two, three, nine and ten. That same spot shows the FCU selected altitude in green when metric units are selected, and feedback messages take priority over the G LOAD. On the right is the gross weight, displayed once the first engine is started, with blue dashes on the ground if nothing is computed. Anywhere on the SD, amber crosses mean a value is not available, and amber dashes over the last digits mean degraded accuracy.
ECAM sequence
Example: the blue reservoir overheats Failure detected: HYD B RSVR OVHT , a level 2 caution Green and yellow are still pressurised Action: BLUE ELEC PUMP ... OFF Blue depressurises : B SYS LO PR follows Users of blue are lost: * F/CTL secondary failure GREEN engine 1 pump YELLOW engine 2 pump BLUE electric pump
Chapter 21 · ECAM Logic, Warnings and Recorders
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow a real failure all the way through, using a system you already know. In flight, the blue hydraulic reservoir overheats. The FWC sees it and generates an amber caution, HYD B RSVR OVHT. The green and yellow systems are unaffected. The procedure asks you to switch off the blue electric pump, to stop heating the fluid. When the crew switches the pump off, the blue system depressurises and drops to zero, so a new line, B SYS LO PR, appears, and because some flight control actuators are powered by blue, the ECAM adds star F slash CTL as a secondary failure. On the next slides we will see the exact cockpit picture at each step, and then what each press of CLR does.
ECAM sequence
Step 2: what the crew sees GREEN BLUE YELLOW PTU ENG 1 PUMP RAT MAN ON ELEC PUMP ENG 2 PUMP ELEC PUMP FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT ON A U T O A U T O H Y D HYD GREEN 3000 BLUE 3000 YELLOW 3000 PSI PSI PTU RAT ELEC 1 2 ELEC OVHT TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG 84.6 84.6 N1 % 612 615 EGT °C 94.1 N2 94.0 1150 FF 1160 KG/H FOB : 13600 S F HYD B RSVR OVHT -BLUE ELEC PUMP........OFF HYD overhead panel E/WD SD: HYD page 1 single chime, MASTER CAUT steady on both sides 2 FAULT light on the BLUE ELEC PUMP pb 3 E/WD: title and blue action line 4 SD calls the HYD page, OVHT amber 5 CLR keys light on the ECP Some failures also light a local warning on the system's own panel, controlled directly by that system.
Chapter 21 · ECAM Logic, Warnings and Recorders
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the cockpit picture when the ECAM detects the overheat. A single chime sounds and both MASTER CAUT lights come on and stay on. On the overhead HYD panel, the FAULT light of the blue electric pump pushbutton is lit. On the engine and warning display, the amber title HYD B RSVR OVHT appears with the blue action line BLUE ELEC PUMP OFF. The system display automatically calls the hydraulic page and shows OVHT in amber next to the blue system. And on the ECAM control panel the CLR keys light up, telling you there is something to clear. So every channel tells the same story: sound, master light, local light on the panel, the message, the synoptic, and the CLR light. Your job is to read it, confirm it on the SD, and act.
ECAM sequence
Steps 3 to 6: actions and CLR Step Crew action What changes 3 BLUE ELEC PUMP pb OFF single chime; FAULT/OFF on the pb; E/WD adds B SYS LO PR; SD shows blue 0 PSI with OVHT; * F/CTL appears; CLR stays lit 4 press CLR (1st) HYD messages leave the E/WD; SD calls the F/CTL page with the blue actuators in amber; CLR still lit 5 press CLR (2nd) CLR and STS lit; E/WD memo area returns to normal; STATUS page appears with the procedures for the rest of the flight 6 press CLR (3rd) CLR goes out; STS reminder on the E/WD; SD back to the flight-phase page End normal configuration memos on the E/WD, flight-phase page on the SD, CLR light out
Rule: after the procedure, press CLR repeatedly until the CLR light goes out. FAULT/OFF on the overhead stays on throughout.
Chapter 21 · ECAM Logic, Warnings and Recorders
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the crew follows the instruction and switches the blue electric pump off. Another single chime sounds, the pushbutton shows FAULT and OFF, the E/WD adds B SYS LO PR, the SD shows zero pressure for blue with the overheat, and the right column shows the secondary failure F/CTL. CLR is still lit. On the first CLR press, the hydraulic messages leave the E/WD, and the SD calls the flight controls page, with the blue actuators in amber, so you can see the consequence. On the second press, the memo area returns to normal and the STATUS page appears with the procedure for the rest of the flight; CLR and STS are lit. On the third press, CLR goes out, an STS reminder appears at the bottom of the E/WD, and the SD returns to the flight phase page. The rule is simple: keep pressing CLR until its light goes out.
ECAM control panel
The ECAM control panel (ECP) ECAM UPPER DISPLAY LOWER DISPLAY OFF BRT OFF BRT T.O CONFIG EMER CANC ENG BLEED PRESS ELEC HYD FUEL APU COND DOOR WHEEL F/CTL ALL CLR STS RCL CLR 1 OFF/BRT knobs upper OFF: E/WD moves to the lower DU 1 2 T.O CONFIG simulates take-off power 2 3 EMER CANC stops aural; cancels a caution for the flight 3 4 System page keys and ALL ALL: every page at 3 s intervals 4 5 CLR (two keys) lit while there is something to clear 5 6 STS and RCL STATUS page; recall cleared alerts 6 5 If the ECP fails, CLR, RCL, STS, EMER CANC and ALL still work: they are wired directly to the FWCs and DMCs Automatic brightness adjustment is superimposed on the manual OFF/BRT setting.
Chapter 21 · ECAM Logic, Warnings and Recorders
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the ECAM control panel on the pedestal. On the left are two OFF BRT knobs, one for each ECAM screen; turning the upper one to OFF moves the engine and warning display to the lower screen automatically. Across the top are T.O CONFIG, which simulates take-off power, and EMER CANC. In the middle are the eleven system page keys and ALL. Along the bottom are two CLR keys, one on each side so either pilot can reach one, STS for the status page and RCL for recall. A detail worth remembering: if the control panel itself fails, CLR, RCL, STS, EMER CANC and ALL still work, because their contacts are wired directly to the flight warning and display management computers. With ALL you can then step through the pages to the one you need. Let us see what each key does in detail.
ECAM control panel
What each key does Key Function CLR lit while a warning or caution, or STATUS, is displayed; each press moves the ECAM to its next display STS STATUS page on the SD, key lit; NORMAL for 3 s if empty; cleared by CLR or a second STS push RCL recalls alerts cleared with CLR that are still active; NORMAL for 3 s if none; lifts flight-phase inhibition until the next phase RCL held > 3 salso recalls alerts cancelled with EMER CANC EMER CANC warning: stops the aural and the MASTER WARN light, message stays. Caution: cancels it for the rest of the flight. Use only for spurious cautions ALL held: all system pages in turn at 3 s intervals; release on the page you want Page key heldwith one ECAM DU: shows that page for up to 3 min (STS: hold, release and push again within 2 s for the next page) T.O CONFIG simulates take-off power; T.O CONFIG NORMAL if correct
Cautions cancelled with EMER CANC come back automatically in phase 1 or 2 after IR 1 and 2 are aligned, or with RCL held for 3 s.
Chapter 21 · ECAM Logic, Warnings and Recorders
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us go key by key. CLR stays lit while a warning, caution or status message is displayed, and each press moves the ECAM to its next display. STS shows the STATUS page, or NORMAL for three seconds if it is empty. RCL recalls alerts that you cleared with CLR but which are still active, or shows NORMAL if there are none, and it lifts the flight phase inhibition until the next phase. Hold RCL for more than three seconds and it also brings back alerts you cancelled with EMER CANC. EMER CANC treats warnings and cautions differently. For a warning it stops the sound and the master light, but the message stays. For a caution it cancels it for the rest of the flight, so it is meant only for spurious cautions. ALL steps through every page at three second intervals. And with a single ECAM screen, holding a page key shows that page for up to three minutes.
OEB reminder
When an OEB changes the ECAM procedure An OEB may supersede an ECAM procedure, its STATUS messages, or both The ECAM warning title stays the same Procedure affected: actions replaced by REFER TO QRH/OEB PROC STATUS affected: REFER TO QRH/OEB PROC title added on the STATUS page STATUS only: procedure kept, plus FOR STS REFER TO OEB OEB reminder: three cases Procedure only HYD B RSVR OVHT REFER TO QRH/OEB PROC E/WD title unchanged STATUS page unchanged Procedure and STATUS HYD B RSVR OVHT REFER TO QRH/OEB PROC E/WD title unchanged STATUS page gains the REFER TO QRH/OEB PROC title STATUS only HYD B RSVR OVHT -BLUE ELEC PUMP.....OFF FOR STS REFER TO OEB E/WD title unchanged STATUS page gains the REFER TO QRH/OEB PROC title
Chapter 21 · ECAM Logic, Warnings and Recorders
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes the manufacturer publishes an operations engineering bulletin, an OEB, which changes how a particular ECAM procedure should be flown. The OEB reminder function flags this in real time, so you never follow an out of date procedure. There are three cases, and in all of them the warning title stays the same. If only the procedure is affected, all its action lines are deleted and replaced by REFER TO QRH OEB PROC, and the STATUS messages are unchanged. If both the procedure and the status are affected, you get the same replacement on the E/WD, and the STATUS page gains the title REFER TO QRH OEB PROC. If only the status is affected, the procedure stays as normal with an extra line, FOR STS REFER TO OEB, and the STATUS page again gains the REFER TO QRH OEB PROC title. In each case the QRH is where the correct procedure lives.
ATA 31-60
Flight data recording FDIMU collects mandatory parameters and stores them in the DFDR DFDR: at least the last 25 h , fireproof and shockproof, with an underwater locator beacon Records automatically: 5 min after power-up, after first engine start , and in flight Stops on the ground 5 min after the second engine shutdown GND CTL pb: manual start on the ground; DFDR EVENT pb: event markSDACs, DMCs, FWCs, FCDCs, BSCU, clock, pbs FDIMU collects and processes DFDR last 25 h at least, fireproof QAR same data, easy access Linear accelerometer 3 axes Automatic recording logic: 5 min power on off flight 1st eng start +5 min 2nd eng off GND CTL pb ON: CVR, DFDR and QAR start on the ground; ON goes off after engine start (back to automatic) DFDR EVENT pb: puts a mark in the flight data AIDS: reports on MCDU or printer, AIDS PRINT pb
Chapter 21 · ECAM Logic, Warnings and Recorders
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flight data recording system records the mandatory parameters. The flight data interface and management unit, the FDIMU, collects them from the SDACs, DMCs, flight warning computers, flight control data concentrators, the brake computer, the clock and a couple of pushbuttons, and stores them in the digital flight data recorder. The DFDR holds at least the last twenty five hours on a fireproof and shockproof memory, with an underwater locator beacon attached. A three axis linear accelerometer adds the accelerations, and a quick access recorder stores the same data where maintenance can reach it easily. Recording is automatic for five minutes after the aircraft is powered, after the first engine start, and always in flight, and it stops five minutes after the second engine shutdown. On the overhead, GND CTL starts the CVR and DFDR manually on the ground, and the EVENT button marks the data.
Summary
The ECAM on one page 84.6 84.6 N1 % 612 615 EGT °C 94.1 N2 94.0 1150 FF 1160 KG/H FOB : 13600 S F LDG LDG GEAR DN SIGNS ON CABIN CHECK SPLRS ARM FLAPS FULL LDG INHIBIT ECAM UPPER DISPLAY LOWER DISPLAY OFF BRT OFF BRT T.O CONFIG EMER CANC ENG BLEED PRESS ELEC HYD FUEL APU COND DOOR WHEEL F/CTL ALL CLR STS RCL CLR STATUS TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG MAX SPD.............250 / .85 APPR PROC DUAL HYD LO PR -IF BLUE OVHT OUT: -BLUE ELEC PUMP.....ON -L/G...........GRVTY EXTN -LDG SPD INCREM.....10KT -LDG DIST PROC.....APPLY CAT 1 ONLY SLATS SLOW INOP SYS G+B HYD CAT 3 G RSVR L+R AIL SPLR 1+3+5 L ELEV AP 1+2 REVERSER 1 NORM BRK NW STEER MAINTENANCE APU AIR COND CANCELLED CAUTION NAV IR 2 FAULT Levels 3: red, CRC, MASTER WARN flashing. 2: amber, single chime, MASTER CAUT. 1: amber only.
Colours Red act now, amber be aware, green normal, white titles, blue actions, magenta special.
Phases 10 FWC phases. T.O INHIBIT 3-5, LDG INHIBIT 7-8. RCL lifts inhibition until the next phase.
Memos T.O memo 2 min after 2nd engine start or T.O CONFIG. LDG memo below 2 000 ft.
SD pages DOOR, WHEEL, ENG, CRUISE, WHEEL, DOOR. Failure and advisory pages replace manual ones.
STATUS Appears when the last alert is cleared or at CONF 1 for approach. STS reminder.
Keys CLR until it goes out. EMER CANC: caution gone for the flight. RCL 3 s brings it back.
Recorders DFDR 25 h. Auto: power-up 5 min, engine start, flight; stops 5 min after shutdown.
Chapter 21 · ECAM Logic, Warnings and Recorders
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us summarise the ECAM. Three levels: red warnings with the continuous chime and flashing MASTER WARN, amber level two cautions with a single chime and MASTER CAUT, and level one cautions with no sound. Six colours, each with a job. Ten flight phases, with take-off inhibition in phases three to five and landing inhibition in seven and eight, and RCL to lift it. The take-off memo two minutes after the second engine start, the landing memo below two thousand feet. The SD pages follow the flight: door, wheel, engine, cruise, wheel, door. The STATUS page appears when you clear the last alert and again at flap one for approach. Keep pressing CLR until it goes out, use EMER CANC only for spurious cautions, and remember RCL for three seconds brings them back. And the DFDR keeps at least twenty five hours. Now try the quiz.