A320 Aircraft Systems · Chapter 16
Flight Controls: Protections, Slats/Flaps and Speedbrakes The five normal law protections, speedbrakes and ground spoilers, the slats and flaps, and the ECAM flight control indications.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the last lesson we built the flight control system and its laws. Now we look at what makes normal law special: its five protections, for load factor, pitch attitude, high angle of attack, high speed and bank angle. For each one you will learn the numbers, what the aircraft does if you push against it, and how to fly out of it. Then we turn to the wing: the speedbrakes, and the logic that deploys the ground spoilers at landing or in a rejected takeoff. After that, the slats and flaps: how they are driven and protected, the lever positions, the difference between configuration one and one plus F, and the alpha lock. We finish with the ECAM flight control page and the memos, so you can read the whole picture in the cockpit.
Flight controls, part two
Protections, speedbrakes and high lift LOAD FACTOR +2.5 / −1 g PITCH ATTITUDE 30° up · 15° down HIGH α α PROT → α MAX HIGH SPEED VMO / MMO BANK ANGLE 33° · 67° SPEEDBRAKES spoilers 2, 3, 4 GROUND SPOILERS spoilers 1 to 5 SLATS AND FLAPS two SFCCs · CONF 0, 1, 1+F, 2, 3, FULL · alpha/speed lock · ECAM indications Protections Load factor, pitch attitude, high α, high speed and bank angle.
Spoilers Speedbrakes, their inhibitions, and the ground spoiler logic.
Slats and flaps SFCCs, PCUs, configurations, 1+F and alpha lock.
Indications ECAM F/CTL page, slat and flap display, memos.
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the second half of chapter twenty seven. We start with the protections of normal law: load factor, pitch attitude, high angle of attack, high speed and bank angle. These are the reason the A320 is often called envelope protected, and they are a favourite subject at interviews and in the simulator. Then we look at the spoilers again, this time as speedbrakes and as ground spoilers, with all their logic. Third, the slats and flaps: the two control computers, the power control units, the lever positions and the surface angles, the special configuration one plus F, and the alpha lock. And to finish, the cockpit indications: the ECAM flight control page, the slat and flap display, and the memos.
Protections
What the protections are for Normal law protects in pitch and roll ; the rudder has no protection Give the pilot maximum authority for the best performance in extreme conditions Reduce the risk of over-controlling or over-stressing the aircraft An instinctive, immediate reaction gives the best possible result Not structural limit protections; never leave the envelope on purposeNormal law protections by mode Ground Rotation* Flight Flare Pitch attitude Load factor High speed High α Bank angle * rotation mode on some aircraft; bank angle is a lateral protection Not structural limit protections e.g. opposite rudder pedal inputs are not protected Never fly outside the envelope on purpose
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does normal law have protections? Keeping the aircraft inside the normal envelope is one of the pilot flying's main jobs, but extreme situations or mishandling can push it outside. The protections give the pilot maximum authority to get the best possible performance in an emergency, reduce the risk of over-controlling or over-stressing the aircraft, and allow an instinctive, immediate reaction that gives the best result, for example pulling fully back to avoid terrain. They are not structural protections. Opposite rudder pedal inputs, for instance, are not protected, and the pilot must never fly outside the envelope deliberately. The table shows where each protection works: pitch attitude in rotation and flight modes, load factor and high speed in flight mode, high angle of attack in rotation, flight and flare modes, and bank angle in flight mode.
Protection 1
Load factor protection Limits: +2.5 g to −1 g clean; +2 g to 0 g with slats or flaps out Emergency reactions are usually hesitant, then aggressive With the limit, the pilot can pull full back at once : 2.5 g without delay If the danger remains, holding full back hands over to high α protection An immediate 2.5 g clears more than a delayed one; no risk of overstress Load factor limits 0 +2.5 g -1 g Clean 0 +2 g 0 g Slats/flaps out Pull full back at once: 2.5 g straight away An immediate 2.5 g clears more terrain than a hesitant pull delayed by two seconds
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
High load factors may be needed in an evasive manoeuvre, to avoid a collision or terrain. The load factor is limited automatically to plus two point five g to minus one g in the clean configuration, and plus two g to zero g with the slats or flaps out. Why does this help? Experience shows that a pilot's first reaction in an emergency is hesitant, then aggressive, and airline pilots are not used to judging g. With the protection, the pilot can instinctively pull the stick fully back, and the aircraft flies two point five g straight away, as you see here, without any risk of over-stressing it. If the danger is still there and the stick stays fully back, high angle of attack protection takes over. An immediate two point five g pull gives more obstacle clearance than a hesitant pull delayed by two seconds.
Protection 2
Pitch attitude protection Nose up 30° in CONF 0 to 3 (reduced to 25° at low speed) Nose up 25° in CONF FULL (reduced to 20° at low speed) Nose down 15° ; limits shown by green = on the PFD pitch scale FD bars removed above 25° up or 13° down ; back within 22° up and 10° down Too high nose-up: rapid energy loss ; too low: rapid energy gain 20 20 10 10 10 10 20 20 30 30 30° up (25° in FULL) 15° down green = marks the pitch limits
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Excessive pitch attitudes are dangerous: too high a nose-up attitude loses energy very quickly, and too low a nose-down attitude gains energy very quickly. And no emergency needs them. So pitch attitude protection limits the nose-up attitude to thirty degrees in configurations zero to three, reduced progressively to twenty five degrees at low speed, and to twenty five degrees in configuration FULL, reduced to twenty degrees at low speed. Nose down, the limit is fifteen degrees. On the PFD, green double bars on the pitch scale mark these limits. The flight director bars also disappear when pitch exceeds twenty five degrees up or thirteen degrees down, and come back once pitch returns between twenty two up and ten down. Pitch attitude protection supports the other three pitch protections. Remember that with the autopilot engaged it is the one protection that does not apply.
Protection 3
High angle of attack protection Above α PROT the stick becomes an α demand instead of a load factor demand Stick neutral: α held at α PROT ; full back: α MAX , just below the 1 g stall Works in dynamic manoeuvres and gusts; gentle turns possible at α MAX No nose-up trim beyond α PROT entry; nose-down trim available At takeoff α PROT = α MAX for 5 s; priority over all other protections angle of attack α C L α PROT α FLOOR α MAX 1 g stall Above α PROT the stick commands α, not g Stick neutral: α PROT held · full back: α MAX, below the stall No nose-up trim beyond α PROT entry Highest priority of all the protections
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
In normal law the aircraft is protected against the stall, even in dynamic manoeuvres or gusts. When the angle of attack passes alpha prot, high angle of attack protection takes over, and the sidestick becomes an angle of attack demand instead of a load factor demand. With no input, the computers hold alpha prot. The crew can increase the angle further, up to alpha max, which is close to, but below, the one g stall. Watch the aircraft: in protection it holds alpha prot, and with the stick held fully back it settles at the maximum angle without stalling. Gentle turns are still possible there. When the pilot releases the stick, the angle returns to alpha prot. Nose-up trim is inhibited beyond the point reached on entry, nose-down trim stays available. At takeoff alpha prot equals alpha max for five seconds, and this protection has priority over all the others.
Protection 3
Low speed on the PFD speed scale VLS : amber strip, the lowest selectable speedV α PROT : top of the amber and black stripV α MAX : top of the red stripAll computed mainly from α: they vary with configuration, weight and load factor Entering the amber and black strip = entering α protection 120 140 160 VLS V α PROT V α MAX current speed PFD speed scale, normal law Computed from α: they move with weight, configuration and g
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the PFD speed scale, normal law shows you how close you are to angle of attack protection. The amber strip marks V L S, the lowest selectable speed. Below it, the amber and black strip begins at V alpha prot, the speed at which alpha protection starts. Lower still, the red strip begins at V alpha max. These speeds are computed mainly from the angle of attack, so they move with configuration, weight and load factor. Pull g in a turn and you will see them creep up the scale towards the current speed. The practical lesson is simple: when the speed trend or the speed itself reaches the amber and black strip, you are entering alpha protection, and nose-up trim stops at that point.
Protection 3
α floor, and flying out of α protection Between α PROT and α MAX, α FLOOR may set go-around thrust automatically Stick held aft with TOGA: the aircraft climbs at a low, steady speed To exit: ease the stick forward below α PROT and add thrust Speed safe: cancel α FLOOR with the instinctive disconnect pb on a thrust lever At high altitude α PROT guards the buffet boundary ; it reduces with Mach Getting out of α PROT 1 Ease the stick forward α below α PROT 2 Add thrust unless α FLOOR has already set TOGA 3 Speed safe again: cancel α FLOOR with the instinctive disconnect pb Stick held aft with TOGA: climbs at a low, steady speed At high altitude α PROT guards the buffet boundary α PROT is reduced as Mach increases Leaving a turn in α PROT, the aircraft may climb
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Between alpha prot and alpha max, the alpha floor function of the autothrust may set go-around thrust automatically, and it usually triggers just after you enter alpha prot. So if the stick is held back, deliberately or not, the aircraft climbs at a fairly constant, low speed. You must not stay there. To leave alpha protection, ease the stick forward to bring the angle below alpha prot, and add thrust, unless alpha floor has already done so. Once a safe speed is regained, cancel alpha floor with the instinctive disconnect button on either thrust lever. The aircraft can also enter alpha prot at high altitude, where it protects against the buffet boundary, because alpha prot reduces as Mach increases. There too, a released stick holds the angle, so when rolling out of a turn in protection the aircraft may climb. On some aircraft a low energy aural alert, computed by the F A C, adds a warning.
Protection 4
High speed protection Active at or above VMO / MMO , depending on acceleration and pitch attitude Nose-down authority reduced progressively ; a permanent nose-up order is applied Full forward stick: authority reaches zero at about VMO + 16 kt / MMO + 0.04 Bank limit 40° , spiral stability back to 0° ; pitch trim frozen (or limited, some aircraft) Off below VMO/MMO. AP disconnects at VMO + 15 / MMO + 0.04 ; overspeed warning VMO + 4 / MMO + 0.006 speed nose-down authority VMO VMO + 16 reduced progressively zero Stick free: small overshoot, then back to the envelope Stick full forward: large overshoot; authority zero at about VMO + 16 kt / MMO + 0.04 Bank limit 40°; spiral stability back to 0° AP off at VMO + 15 kt / MMO + 0.04 Overspeed warning: VMO + 4 kt / MMO + 0.006
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
High speed protection makes the aircraft recover automatically from a high speed upset. It activates at or above V M O or M M O, depending on how fast the aircraft is accelerating and how low the nose is. As speed rises above the limit, the sidestick's nose-down authority is reduced progressively, and a permanent nose-up order helps the recovery, as you see here. With the stick free, the aircraft overshoots slightly and returns into the envelope. With the stick held fully forward it overshoots much more, and at about V M O plus sixteen knots, or M M O plus point zero four, nose-down authority reaches zero, although the speed is not guaranteed to stop there. Bank is limited to forty degrees and the aircraft rolls back to wings level when released. The autopilot disconnects at V M O plus fifteen, and the overspeed warning sounds at V M O plus four.
Protection 5
Bank angle protection Up to 33° : bank held with the stick neutral Above 33°: spiral stability , stick released → back to 33° Full lateral stick: 67° and no further α or pitch protection active: 45° max; high speed protection: 40° , back to 0° Above 45° : AP off, FD bars removed (back below 40°); auto trim off while the protection works Bank angle protection 0° 33° 45° 67° released: back to 33° 0–33°: bank held with the stick free 33–67°: spiral stability, back to 33° when released 67°: limit with full lateral stick α or pitch protection: 45° · high speed protection: 40° AP off and FD bars removed above 45° (FD back below 40°)
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bank angle protection works in flight mode. Up to thirty three degrees, the system holds the bank angle when the stick is neutral. Now the pilot holds full lateral stick, as in this animation: the bank increases to sixty seven degrees and no further. Then the pilot releases the stick. Above thirty three degrees the system restores positive spiral static stability, so the bank comes back to thirty three degrees by itself. If angle of attack or pitch attitude protection is active, the maximum is forty five degrees, and in high speed protection it is forty degrees, with the aircraft rolling back to wings level when let go. While bank angle protection is active, auto trim is inoperative. And above forty five degrees, the autopilot disconnects and the flight director bars disappear, coming back when the bank is below forty degrees.
Using the protections
Turns, and the protections law by law Protection Normal law Alternate law Direct law Load factor +2.5 / −1 g clean, +2 / 0 g out as normal law none Pitch attitude 30° (25° FULL) up, 15° down none: amber X none High α α PROT / α MAX, α FLOOR low speed stability, stall warning stall warning only High speed nose-up order, 40° bank high speed stability, overspeed warning overspeed warning only Bank angle 33° / 67° none none Turn up to 33° no pitch or rudder input once established — — Steep turn above 33° hold lateral pressure for bank, aft pressure for level — —
Alternate law without reduced protection keeps only the load factor limit.
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table compares the protections law by law, and adds how you actually fly a turn. In normal law you have all five. In alternate law the load factor limit stays, pitch attitude and bank angle protections are gone, and the angle of attack and high speed protections are replaced by the low and high speed stabilities, with conventional stall and overspeed warnings. In direct law there are no protections at all, only the warnings. Now the turns. In a normal turn up to thirty three degrees, you roll in with lateral stick, and once established you need neither a pitch correction nor rudder. In a steep turn beyond thirty three degrees, you must hold lateral pressure to keep the bank, because the aircraft wants to go back to thirty three, and aft pressure to keep level flight.
Spoilers
Five spoilers per wing, three jobs L AIL B G ELAC 1, 2 5 G SEC 2 4 Y SEC 1 3 B SEC 1 2 Y SEC 3 1 G SEC 3 1 G SEC 3 2 Y SEC 3 3 B SEC 1 4 Y SEC 1 5 G SEC 2 R AIL G B ELAC 1, 2 FUSE LAGE ROLL: aileron + spoilers 2 to 5 SPEEDBRAKES: 2, 3, 4 GROUND SPOILERS: 1 to 5 ROLL: spoilers 2 to 5 + aileron SPEEDBRAKES: 2, 3, 4 GROUND SPOILERS: 1 to 5 Hydraulics: G green B blue Y yellow A SEC fault: its spoilers retract, and the symmetric pair is inhibited
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before the speedbrake logic, let us look at the spoilers again. There are five on each wing, numbered from the root outwards. They have three jobs. For roll, the aileron works with spoilers two to five on the down-going wing. As speedbrakes, spoilers two, three and four extend on both wings. As ground spoilers, all five extend on both wings to dump lift on the runway. Each spoiler is powered by one hydraulic system, green for one and five, yellow for two and four, blue for three, and driven by one S E C. If a S E C fails, its spoilers retract, and if any spoiler fails, the matching one on the other wing is inhibited, so the aircraft stays symmetric.
Speedbrakes
Speedbrakes and their inhibitions Spoilers 2, 3 and 4 , set with the SPEED BRAKE lever Inhibited: SEC 1 and SEC 3 both faulty, an elevator fault, α protection , α floor Also inhibited: flaps FULL (3 or FULL on some aircraft), thrust levers above MCT Inhibited while out: they retract and stay in until the condition clears and the lever is reset (≥ 10 s) Roll has priority : the opposite speedbrake retracts if a roll order needs more travel Speedbrake extension is inhibited by… 1 SEC 1 and SEC 3 both faulty 2 L or R elevator faulty 3 α protection active 4 α FLOOR activated 5 Flaps FULL (3 or FULL on some aircraft) 6 Thrust lever above MCT Inhibited while extended: they retract and stay in until the condition clears and the lever is reset; usable again ≥ 10 s later
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The speedbrakes are spoilers two, three and four, controlled with the SPEED BRAKE lever on the pedestal. Move the lever and they rise symmetrically on both wings, as here, and come back when you retract it. Extension is inhibited if S E C one and S E C three are both faulty, if either elevator is faulty, if angle of attack protection or alpha floor is active, if the flaps are at FULL, or on some aircraft at three or FULL, and if a thrust lever is above M C T. If an inhibition occurs while they are out, the speedbrakes retract automatically and stay retracted until the condition has gone and the crew has reset the lever; they can then be used again ten seconds or more after the reset. Roll always has priority: if a roll order plus a speedbrake order needs more travel than is available, the speedbrake on the other wing retracts.
Speedbrakes
How far, and with the autopilot Lever pushed down and moved; hard point at ½ Newer standard, manual flight: 40° spoilers 3 and 4, 20° spoiler 2 With the AP : 25° and 12.5° , reached at ½ ; beyond ½ adds nothing Faster than 315 kt / M 0.75 with AP: slow retraction, FULL to clean in about 25 s Speedbrake surface failed: the symmetric one is inhibited; on the ground, stopped, the lever moves spoilers 1 (maintenance) SPEED BRAKE RET RET 1/4 1/4 1/2 1/2 3/4 3/4 FULL FULL hard point at ½ Max speedbrake deflection (newer standard) Manual: spoilers 3, 4 40° Manual: spoiler 2 20° AP: spoilers 3, 4 25° AP: spoiler 2 12.5° AP: full deflection reached at ½; lever ½ → FULL adds nothing Other standards: 25° (3, 4) and 12.5–25° for spoiler 2
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
To set the speedbrakes, push the lever down and move it to the position you want. There is a hard point at the half position. How far the surfaces travel depends on the aircraft standard. On the newer standard, in manual flight, spoilers three and four go to forty degrees and spoiler two to twenty. With the autopilot engaged the maximum is twenty five and twelve and a half degrees, and that is already reached at the half position, so moving the lever from half to full gains nothing. On other standards the maximum is twenty five degrees, with the same or a smaller value for spoiler two. Above three hundred and fifteen knots or Mach point seven five with the autopilot engaged, retraction is deliberately slow, about twenty five seconds from full to clean. And for maintenance, with the aircraft stopped on the ground, the lever moves spoilers one.
Ground spoilers
Ground spoilers: arming and full extension All five spoilers, full extension , both wings (plus aileron anti-droop on some aircraft) Arm : pull the speedbrake lever up in the RET position; memo GND SPLRS ARMED RTO above 72 kt wheel speed: armed → both levers to idle ; not armed → reverse on one engine Landing, armed: both main gears on the ground with the levers at idle Landing, not armed: both main gears down and reverse selected SPEED BRAKE RET RET 1/4 1/4 1/2 1/2 3/4 3/4 FULL FULL pulled UP at RET: ARMED GND SPLRS ARMED Rejected takeoff, wheel speed > 72 kt armed: both levers to idle not armed: reverse on one engine Landing armed: both main gears down, levers at idle not armed: both main gears down + reverse selected Then: all 5 spoilers, full extension, both wings Disarm to retract after landing or RTO
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ground spoiler function uses all five spoilers on each wing at full extension, and on some aircraft the ailerons too. The crew arms it by pulling the speedbrake lever up while it is in the retracted position, and the green memo GND SPLRS ARMED appears. In a rejected takeoff above seventy two knots wheel speed, armed ground spoilers extend as soon as both thrust levers are back at idle. If they were not armed, they extend when reverse is selected on one engine, with the other lever at idle. At landing, armed ground spoilers extend as soon as both main gears have touched down with the levers at idle. Here the aircraft has touched down, and all the spoilers come up, putting the weight on the wheels for braking. If they were not armed, they still extend once both main gears are down and reverse is selected.
Ground spoilers
The complete ground spoiler logic REJECTED TAKEOFF (wheel speed > 72 kt) Armed: both thrust levers back to idle → FULL Not armed: reverse selected on one engine (other lever at idle) → FULL LANDING: full extension Armed (or lever not at RET): both main gears on ground and levers at idle, or reverse → FULL Not armed: both main gears + reverse → FULL PARTIAL extension (phased lift dumping) One main gear on ground and armed + levers at idle, or not armed + reverse on one engine → less lift, the second gear compresses → FULL RETRACTION After landing or RTO: when the crew DISARMS the ground spoilers Touch and go: one thrust lever advanced above 20° Bounce (some aircraft): armed, both gears down, levers ≤ CLB → partial extension to soften the bounce A failed surface: the symmetric one is inhibited AILERON ANTI-DROOP (some aircraft) Both ailerons deflect up with the ground spoilers when: ground spoilers fully extended, flaps not clean, pitch below 2.5°, flying manually, normal law, one aileron servocontrol available on each side → even more lift dumped
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the complete logic in one picture. The top row is extension: rejected takeoff on the left, landing in the middle, and partial extension on the right. Partial extension, also called phased lift dumping on newer aircraft, deploys the spoilers to a reduced angle when only one main gear is on the ground, either armed with the levers at idle, or not armed with reverse selected. The reduced lift lets the second gear compress, and then full extension follows. On some aircraft, if the crew mishandles the thrust levers in the flare and the aircraft bounces, a partial extension also helps. The bottom left is retraction: after landing or a rejected takeoff, when the crew disarms, and in a touch and go, when one thrust lever is advanced above twenty degrees. Bottom right, on some aircraft, the ailerons also deflect up with the spoilers, the aileron anti-droop, under the listed conditions.
Slats and flaps
The slat and flap system Per wing: 5 slats and 2 flaps , electrically controlled, hydraulically operated FLAPS lever on the pedestal, five positions; 2 SFCCs , each with a slat and a flap channelSlat PCU: blue + green motors · flap PCU: green + yellow , via a differential gearbox POBs lock the drive at the selected position or if hydraulic power failsDouble-slotted flaps on some aircraft (the longer-fuselage type) Right wing from above (high lift extended) 1 2 3 4 5 inner flap outer flap aileron 5 slats on the leading edge Slats: blue + green motors · Flaps: green + yellow motors Both driven by shafts from one PCU each
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each wing has five slats on the leading edge and two flaps on the trailing edge. They are controlled electrically and moved hydraulically, and the crew selects them with the FLAPS lever on the pedestal, which has five positions. Watch them extend: slats first in position one, then slats and flaps together in position two, and further still at FULL. Two slat flap control computers, the S F C Cs, each contain a slat channel and a flap channel. The power control units have two independent hydraulic motors joined by a differential gearbox: blue and green for the slats, green and yellow for the flaps. Pressure-off brakes, the P O Bs, lock the transmission when the surfaces reach the selected position, or if hydraulic power fails. Some aircraft, the longer-fuselage version, have double-slotted flaps.
Slats and flaps
High-lift architecture and its safety devices FLAPS 0 0 1 1 2 2 3 3 FULL FULL SFCC 1 SFCC 2 slat + flap channel each SLAT PCU diff. gearbox blue green FLAP PCU diff. gearbox green yellow POB brakes lock the drive at the selected position or if hydraulics fail 5 slats per wing WTB at each wing end (B + G) APPU: asymmetry 2 flaps per wing WTB: left B + Y, right B + G flap disconnect sensor FPPU → SFCC feedback · IPPU → ECAM position pick-off units One SFCC or one hydraulic system lost: that drive runs at half speed WTBs cannot be released in flight. Flap WTB on: slats still work; slat WTB on: flaps still work.
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the architecture with its safety devices. From the lever, both S F C Cs command the two power control units, which turn transmission shafts running out along each wing. At the wing ends, the wing tip brakes, the W T Bs, stop the shafts if the surfaces move without a command: a runaway, an asymmetry or an overspeed. The slat and right flap brakes use blue and green, the left flap brakes blue and yellow. Once on, they cannot be released in flight. An asymmetry position pick-up unit measures any difference between the left and right wings, a flap disconnect sensor detects a broken flap attachment by measuring excessive differential movement between the inner and outer flaps, feedback units send positions to the S F C Cs, and an instrumentation unit sends positions to the ECAM. If one S F C C fails, slats and flaps both run at half speed. If one hydraulic system fails, only its surfaces run at half speed.
Configurations
Lever positions and surface angles Lever Slats Flaps ECAM Used for 0 0° 0° (clean) Cruise 1 18° 0° 1 Holding 1 18° 10° 1+F Takeoff 2 22° 15° 2 Takeoff, approach 3 22° 20° 3 Takeoff, approach, landing FULL 27° 40° FULL Landing
Other variants: FULL flaps 35°; double-slotted (longer-fuselage) type 2 = 22/14, 3 = 22/21, FULL = 27/25. Balks at 1 and 3; no intermediate positions.
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the table to know by heart, given here for the A320 standard. Lever zero is clean, for cruise. Lever one gives two configurations: slats eighteen with flaps zero, shown as one, used for holding, and slats eighteen with flaps ten, shown as one plus F, used for takeoff. Lever two gives slats twenty two, flaps fifteen, for takeoff or approach. Lever three gives slats twenty two, flaps twenty, for takeoff, approach or landing. And FULL gives slats twenty seven, flaps forty, for landing. Other variants differ: on some, FULL flap is thirty five degrees, and the double-slotted version uses fourteen, twenty one and twenty five degrees. The crew must pull the lever out of its detent to move it, there are balks at one and three so you cannot ask for too much travel in one movement, and there are no intermediate positions.
Configurations
CONF 1 or 1+F? Takeoff in 1+F (18°/10°): flaps retract automatically at 210 kt if the crew has not selected 0 In CONF 1+F , the flaps retract before VFE is reached Lever from 2 or 3 to 1: 1+F below 210 kt (also in a go-around) Lever from 0 to 1 in flight: CONF 1 (18°/0°) After flap retraction, 1+F only at or below 100 kt , unless 2, 3 or FULL was selected before CONF 0 clean 1 + F 18 / 10 CONF 1 18 / 0 CONF 2 22 / 15 ≤ 100 kt > 100 kt > 210 kt: flaps retract ≤ 100 kt < 210 kt > 210 kt lever moved to 1: from 0 (top) or from 2 (bottom)
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Lever position one gives two configurations, and which one you get depends on where you come from and how fast you are going. For a takeoff in position one, you get one plus F, slats eighteen and flaps ten. If the crew forgets to select zero after takeoff, the flaps retract automatically at two hundred and ten knots, before reaching the flap limit speed, leaving configuration one. When you come back from two or three to one, for example after a takeoff or a go-around in configuration two, you get one plus F below two hundred and ten knots. But from zero to one in flight, you get configuration one, slats only. And once the flaps have retracted, one plus F is not available again until the speed is a hundred knots or less, unless two, three or FULL was selected before. And in configuration one, if the speed falls to a hundred knots, the flaps extend to ten degrees automatically.
Slats
The alpha/speed lock Stops the slats retracting at high α or low speed , using α and speed from the ADIRUs Lever to 0 with α above 8.5° or speed below 148 kt : slats stay out, A-LOCK pulses They retract when α is below 7.6° and speed above 154 kt Not triggered if the lever was already at 0; not active on the ground below 60 kt Some aircraft: 8.0° / 165 kt, released at 7.1° or 171 kt speed angle of attack 148 154 kt 8.5° 7.6° slats stay out slats retract FLAPS lever to 0 with α > 8.5° or speed < 148 kt: slats held, A-LOCK pulses green They retract once α < 7.6° and speed > 154 kt Other standards: 8.0° / 165 kt, release 7.1° or 171 kt Not active on the ground below 60 kt
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The alpha speed lock protects you from retracting the slats too early. The S F C Cs use angle of attack and airspeed from the air data and inertial reference units. When the FLAPS lever is set to zero, and the angle of attack is above eight and a half degrees, or the speed is below one hundred and forty eight knots, slat retraction is inhibited, and A-LOCK pulses in green on the ECAM. The slats then retract once the angle of attack is below seven point six degrees and the speed is above one hundred and fifty four knots. If either condition appears after the lever is already at zero, nothing happens: the slats keep retracting or stay at zero. The function is not active on the ground below sixty knots. On some aircraft the values are eight degrees and one hundred and sixty five knots, released at seven point one degrees or one hundred and seventy one knots.
Indications
The slat and flap display on the E/WD White dots: the selectable positions (not shown when clean) Green boxes: actual slat and flap positions; cyan target while in transit Lever legend (1, 1+F, 2, 3, FULL): green when reached, cyan in transit S and F white; amber for a fault, WTB on, or both hydraulic systems lostS LOCKED / F LOCKED amber with an ECAM caution; A-LOCK pulsing greenS F 2 CONF 2 set: lever position green, actual positions green S F FULL moving to FULL: target and lever legend cyan S / F amber + S LOCKED / F LOCKED: wingtip brakes on or flap misalignment A-LOCK pulses: alpha/speed lock active
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The slat and flap indication sits on the engine and warning display. The small white dots are the selectable positions, and they are not shown in the clean configuration. The green boxes show where the slats and flaps actually are. While they are moving, the selected position appears as a cyan box and the lever legend, such as FULL, is cyan; when the surfaces arrive, the target disappears and the legend turns green. The letters S and F are normally white. They turn amber, together with the position boxes, if both hydraulic systems for that surface fail, unless you are on the ground with both engines stopped, if the wing tip brakes are on, or if there is a fault. S LOCKED or F LOCKED appears in amber, with an ECAM caution, when the wing tip brakes are applied or two flaps are misaligned. And A-LOCK pulses green when the alpha lock is active.
Indications
The ECAM F/CTL page F/CTL G B Y SPD BRK L AIL B G R AIL G B ELAC 1 2 SEC 1 2 3 PITCH TRIM G Y 0.4° UP L ELEV B G R ELEV Y B RUD G B Y TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG 1 Spoilers: – retracted, Δ deflected > 2.5° (green) 2 G B Y: hydraulic pressure, amber when low 3 L / R AIL: scale white, index green 4 ELAC 1 2 · SEC 1 2 3: green numbers; amber if failed or OFF 5 PITCH TRIM: position (green); legend amber if jammed 6 L / R ELEV: index green; amber if both actuators lost 7 Actuator letters under each surface 8 RUD: rudder (green), travel limit, trim (cyan)
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the ECAM flight control page. Across the top are the spoilers of both wings, with SPD BRK between them: a green dash means retracted, a green triangle means deflected by more than two and a half degrees. Above them are the hydraulic letters, green, turning amber with low pressure. On each side, the aileron scales, white with a green index. In the middle, E L A C one and two and S E C one, two and three, with green numbers that turn amber if the computer fails or is switched off. Below, the pitch trim position in degrees, then the two elevator scales, and under each surface the letters of its actuators, G and B for the left elevator, Y and B for the right. At the bottom, the rudder: its position, the travel limiter marks and the rudder trim in cyan.
Indications
Reading failures, and the memos Spoiler: amber Δ fault deflected · amber number fault retracted · amber × position not valid Aileron index amber: neither green nor blue jack available; elevator index amber: both actuators lost Pitch trim figures amber: green and yellow low; PITCH TRIM legend amber: jam Rudder amber: all three systems low; TLU amber: both travel limiters failed; trim amber: reset failed Memos: GND SPLRS ARMED green; SPEED BRK green when out, amber when they should be retracted F/CTL G B Y 5 5 SPD BRK L AIL B G R AIL G B ELAC 1 2 SEC 1 2 3 PITCH TRIM G Y 1.2° UP L ELEV B G R ELEV Y B RUD G B Y TAT +19 °C SAT +18 °C 23 H 56 GW 60300 KG SEC 2 failed: amber SEC 2, both spoilers 5 fault retracted amber number = fault retracted · amber × = position not valid GND SPLRS ARMED SPEED BRK SPEED BRK
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now a failed page. Here S E C two has failed: its box is amber, and spoiler five on each wing, which S E C two drives, shows an amber number, meaning faulty and retracted. Remember the other two amber spoiler symbols: an amber cross means the position is not valid, and an amber triangle means faulty but deflected. A hydraulic letter turns amber when that system's pressure is low. An aileron index turns amber when neither its green nor its blue jack is available, and an elevator index when both its actuators are lost. The pitch trim figures turn amber with green and yellow both low, and the PITCH TRIM legend turns amber if the trim jams. The rudder turns amber with all three systems low. The same spoiler symbols appear on the WHEEL page. Finally the memos: GND SPLRS ARMED in green, and SPEED BRK, green when extended, amber when they should be retracted, for example with thrust applied.
Summary
Protections and high lift in one page Load factor and pitch +2.5/−1 g clean, +2/0 g out. Pitch 30° up (25° FULL), 15° down; green = marks.
High α α PROT: stick demands α; full back = α MAX, no stall. α FLOOR: TOGA. Exit: stick forward, thrust, cancel.
High speed and bank Nose-up order above VMO/MMO, bank 40°. Bank held to 33°, max 67° (45° in α prot).
Spoilers SPD BRK 2, 3, 4: inhibitions, reset, roll priority. Ground spoilers 1–5: armed at idle, not armed with reverse.
Slats and flaps 2 SFCCs, PCUs B+G / G+Y. 1+F 18/10, auto-retract at 210 kt. Alpha lock 8.5° / 148 kt.
Indications F/CTL page: green normal, amber failed. S/F LOCKED, A-LOCK, GND SPLRS ARMED, SPEED BRK.
Chapter 16 · Flight Controls: Protections, Slats/Flaps and Speedbrakes
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us recap. The load factor is limited to plus two point five and minus one g clean, plus two and zero with high lift out. Pitch is limited to thirty degrees up, twenty five in FULL, and fifteen down. Above alpha prot the stick commands angle of attack, full back gives alpha max without a stall, and alpha floor adds go-around thrust; to get out, ease forward, add thrust and cancel alpha floor. Above V M O a nose-up order recovers the aircraft and bank is limited to forty degrees. Bank is held up to thirty three degrees and limited to sixty seven. The speedbrakes are spoilers two to four, with their inhibitions and roll priority, and the ground spoilers use all five. The slats and flaps are driven by two S F C Cs and two power units; one plus F retracts at two hundred and ten knots; the alpha lock holds the slats. And read the F/CTL page: green is normal, amber is failed.