A320 Aircraft Systems · Chapter 15
Flight Controls: Architecture and Control Laws The A320 fly-by-wire system: computers, surfaces and actuators, the normal law and its pitch modes, sidesticks, and the alternate, direct and mechanical reconfigurations.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the flight controls of the A320, the system that made this aircraft famous. There are no control cables from the sidesticks to the surfaces. Instead, seven computers read your inputs and move hydraulic actuators, and in normal law they keep the aircraft inside a safe envelope. In this lesson we build the system from the ground up: the computers and who controls what, how each surface is powered and backed up, and then the control laws, starting with normal law and its pitch modes from the takeoff roll to the flare. We look at the sidesticks and their priority logic, and finish with the degraded laws: alternate, direct, abnormal attitude and the mechanical backup. The protections, the slats and flaps, and the speedbrakes come in the next lesson.
Flight controls
Our route through ATA 27, part one ELAC 1 ELAC 2 SEC 1 SEC 2 SEC 3 FAC 1 FAC 2 elevators, THS, ailerons spoilers, standby elevator and THS rudder: yaw damper, trim, travel limit Seven fly-by-wire computers, plus two FCDCs that pass their data to the ECAM and the maintenance system Architecture Seven computers, the surfaces, and how each is actuated and backed up.
Normal law Pitch modes from ground to flare, auto trim, lateral law, LAF.
Sidesticks Autopilot override, dual input and the priority logic.
Reconfiguration Alternate, direct, abnormal attitude and mechanical backup.
Chapter 15 · Flight Controls: Architecture and Control Laws
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the first half of chapter twenty seven. Across the top are the seven fly-by-wire computers: two E L A Cs, three S E Cs and two F A Cs. We start with the architecture: which computer moves which surface, how each surface is actuated, and how it is backed up when something fails. Then we study normal law, the law you fly every day, with its pitch modes from the takeoff roll through to the flare, auto trim and its limits, and the lateral law. Third come the sidesticks, including how to take priority. And finally the reconfiguration laws: alternate, direct, abnormal attitude and the mechanical backup. The protections themselves, the slats and flaps and the speedbrakes are in the next lesson.
Basic principle
Fly-by-wire: signalled by wire, moved by hydraulics Every surface is electrically controlled and hydraulically actuated The stabiliser and rudder can also be controlled mechanically Sidesticks fly pitch and roll; yaw indirectly through turn coordinationComputers interpret the inputs and move the surfaces In normal law they prevent excessive manoeuvres in pitch and roll ; the rudder has no such protection aileron spoilers 1-5 elevator + THS rudder All surfaces: electrically signalled, hydraulically moved
Chapter 15 · Flight Controls: Architecture and Control Laws
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 is a fly-by-wire aircraft. Every flight control surface is controlled electrically and moved hydraulically. Two surfaces keep a mechanical path as well: the trimmable stabiliser, through the trim wheels, and the rudder, through the pedals. The pilots fly pitch and roll with sidesticks, and yaw is handled indirectly, by automatic turn coordination. Watch the surfaces respond: first the ailerons with the roll spoilers on one wing, then the elevators, and finally the rudder on the fin. Between your hand and those surfaces sit computers that interpret what you ask for. In normal law, whatever you do with the stick, they will not let the aircraft make an excessive manoeuvre or leave the safe envelope in pitch or roll. Remember the exception: just like on a conventional aircraft, the rudder has no such protection.
Control surfaces
How each surface is controlled Axis Surface Control Hydraulics Pitch Two elevators Electrical L: green + blue · R: yellow + blue Pitch Trimmable horizontal stabiliser Electrical (normal, alternate) · mechanical (trim wheel) Green + yellow motors Roll Ailerons (one per wing) Electrical Green + blue on each Roll Spoilers (roll: 2–5) Electrical 1 and 5 green, 2 and 4 yellow, 3 blue Yaw Rudder Mechanical; yaw damping, turn coordination and trim electrical Green, blue and yellow jacks Drag Speedbrakes (spoilers 2–4) Electrical as for the spoilers
Note: all surfaces are hydraulically actuated, so a total hydraulic loss would leave no surface moving.
Chapter 15 · Flight Controls: Architecture and Control Laws
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table pulls together how each surface is controlled, a favourite oral question. In pitch, the two elevators are electrical. The stabiliser is electrical in normal and alternate law, and mechanical when you use the trim wheel. In roll, the ailerons and the spoilers are electrical. In yaw, the rudder is mechanical, through the pedals, but yaw damping, turn coordination and rudder trim reach it electrically. The speedbrakes, which are spoilers two, three and four, are electrical. Now look at the hydraulics column. The left elevator has green and blue jacks, the right one yellow and blue, each aileron green and blue, the spoilers are spread across all three systems, and the rudder has a jack from each system. Remember the note at the bottom: every surface needs hydraulic power to move.
Computers
Seven computers and their pushbuttons 2 ELACs (elevator aileron computers): normal elevator and THS control, aileron control3 SECs (spoiler elevator computers): spoilers; standby elevator and THS (SEC 1 and 2)2 FACs (flight augmentation computers): electrical rudder control2 FCDCs send ELAC and SEC data to the ECAM and maintenance systempb OFF then ON resets the computer; amber FAULT + ECAM caution on failure FLT CTL ELAC 1 FAULT OFF SEC 1 FAULT OFF FAC 1 FAULT OFF Captain side overhead FLT CTL ELAC 2 FAULT OFF SEC 2 FAULT OFF SEC 3 FAULT OFF FAC 2 FAULT OFF F/O side FAULT (amber) + ECAM caution: failure detected ELAC FAULT also lit during its 8 s power-up test OFF (white): computer inactive; OFF then ON = reset
Chapter 15 · Flight Controls: Architecture and Control Laws
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Seven computers process the pilot and autopilot inputs. Two E L A Cs, the elevator aileron computers, give normal elevator and stabiliser control, and aileron control. Three S E Cs, the spoiler elevator computers, control the spoilers, and S E C one and two also provide standby elevator and stabiliser control. Two F A Cs, the flight augmentation computers, give electrical rudder control. Two more units, the F C D Cs, are data concentrators: they collect E L A C and S E C data for the ECAM and the maintenance system. On the overhead, each computer has a pushbutton. Selecting OFF makes it inactive, and OFF then ON resets it, which is a common ECAM action. The amber FAULT light comes on with an ECAM caution when a failure is detected, and for an E L A C also during its eight second power-up test.
Architecture
Who moves what: the architecture LEFT WING RIGHT WING L AIL B G ELAC 1, 2 5 G SEC 2 4 Y SEC 1 3 B SEC 1 2 Y SEC 3 1 G SEC 3 1 G SEC 3 2 Y SEC 3 3 B SEC 1 4 Y SEC 1 5 G SEC 2 R AIL G B ELAC 1, 2 fuselage ELEVATORS L ELEV G B R ELEV Y B ELAC 2 (G and Y jacks) then ELAC 1 (B jacks) then SEC 1 or SEC 2 STABILISER (THS) screwjack: 2 hydraulic motors G Y 1 2 3 electric motors 1, 2, 3 motor 1: ELAC 2 · motor 2: ELAC 1 SEC 1 or 2: motor 2 or 3 + mechanical trim wheels RUDDER 3 servojacks in parallel G B Y yaw damper actuators: G (FAC 1), Y (FAC 2) travel limit + trim: FAC 1, 2 pedals: mechanical SLATS AND FLAPS SLATS B G FLAPS G Y two SFCCs one motor per hydraulic system in each PCU
Chapter 15 · Flight Controls: Architecture and Control Laws
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole architecture on one page. Across the top, both wings: each aileron has a green and a blue jack and is driven by E L A C one, with E L A C two as the backup. The five spoilers on each wing are powered green, yellow, blue, yellow, green from spoiler one to five, and each is driven by one S E C: S E C three for spoilers one and two, S E C one for three and four, and S E C two for spoiler five. Below, the elevators: E L A C two first, using the green jack on the left and the yellow jack on the right, then E L A C one with both blue jacks, then a S E C. The stabiliser has green and yellow hydraulic motors and three electric motors. The rudder has three jacks, with green and yellow yaw damper actuators on the two F A Cs.
Pitch control
Elevators and stabiliser Elevators: 30° nose up, 17° nose down ; THS: 13.5° up, 4° down Normal: ELAC 2 drives the elevators (L green jack, R yellow jack) and THS motor 1 ELAC 2, its hydraulics or jacks fail: ELAC 1 takes over with the blue jacks and THS motor 2 Both ELACs lost: SEC 1 or SEC 2 with THS motor 2 or 3 Trim wheel : mechanical THS control at any time if green or yellow is available30° up 17° down Elevators max 30° nose up, 17° nose down Trimmable horizontal stabiliser max 13.5° nose up, 4° nose down ELAC 2 → ELAC 1 → SEC 1 or 2
Chapter 15 · Flight Controls: Architecture and Control Laws
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pitch is controlled by two elevators and the trimmable horizontal stabiliser. The elevators travel thirty degrees nose up, watch them go, and seventeen degrees nose down. The stabiliser travels thirteen and a half degrees nose up and four degrees nose down. In normal operation E L A C two is in charge of pitch. It drives the left elevator with its green jack, the right elevator with its yellow jack, and the stabiliser through electric motor number one. If E L A C two fails, or its hydraulic systems or jacks fail, pitch control shifts to E L A C one, which uses the blue jacks on both elevators and electric motor number two. If both E L A Cs are lost, S E C one or S E C two takes over, with stabiliser motor two or three. And the trim wheels can move the stabiliser mechanically at any time, provided green or yellow is pressurised.
Pitch actuation
Elevator servojacks: active, damping, centering Two electrically controlled hydraulic servojacks per elevator Normal: one jack active , the other in damping ; some manoeuvres make both active Active jack fails: the damping jack becomes active, the failed one goes to damping Neither jack electrically controlled: both centering ; neither hydraulically: both damping One elevator lost: the other's deflection is limited to protect the tail ACTIVE position controlled electrically DAMPING follows the surface (free, damped) CENTERING held hydraulically at neutral Normal: one jack active, the other damping Active jack fails: the damping jack takes over No electrical control: both centre · no hydraulics: both damp
Chapter 15 · Flight Controls: Architecture and Control Laws
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each elevator has two servojacks, and each servojack has three modes. In active mode, its position is controlled electrically by a computer. In damping mode, it simply follows the surface, acting like a shock absorber. In centering mode, it is held hydraulically at neutral. Normally one jack is active and the other is damping, although some manoeuvres bring the second jack in as active too. If the active jack fails, the damping jack becomes active and the failed one switches to damping. If neither jack can be controlled electrically, both go to centering, so the elevator is held at neutral. If neither has hydraulic pressure, both go to damping. Finally, if one whole elevator fails, the computers limit the deflection of the other one, to avoid asymmetric loads on the tailplane and the rear fuselage.
Pitch actuation
The THS actuator and the trim wheels A screwjack driven by two hydraulic motors (green and yellow) Motors controlled by one of three electric motors , or by the trim wheels Trim wheels: mechanical, priority over electrical control; moving them disconnects the AP Before takeoff: set the THS for the CG using the scale and green band on the wheel After nosewheel touchdown (pitch < 2.5° for 5 s): trim resets to zero (needs G or Y) nut THS pivot gearbox green motor yellow motor M1 M2 M3 3 electric motors (one at a time) trim wheels mechanical, priority
Chapter 15 · Flight Controls: Architecture and Control Laws
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The stabiliser is moved by a screwjack. Two hydraulic motors, one green and one yellow, turn it through a gearbox, and the nut drives the stabiliser leading edge, so it pivots about its rear attachment. For nose up trim, as here, the leading edge moves down. The hydraulic motors are controlled either by one of three electric motors, commanded by the E L A Cs or S E Cs, or mechanically by the pitch trim wheels, which have priority over electrical control. Moving a wheel disconnects the autopilot, but not the E L A Cs, which stay synchronised with the position. Before takeoff the crew sets the stabiliser for the C G, using the scale and the green band on the wheel. After landing, once the nosewheel is down and pitch is below two and a half degrees for five seconds, trim resets to zero automatically, if green or yellow is pressurised.
Roll control
Ailerons and roll spoilers Per wing: one aileron (25°) and four roll spoilers , 2 to 5 (35°) Ailerons droop 5° when the flaps are extended ELAC 1 controls the ailerons; ELAC 2 if it fails; both lost: ailerons go to damping Two jacks per aileron, one at a time; damping also if blue and green are both low SEC fails: its spoilers retract ; hydraulics lost: spoiler holds its position or less; the symmetric spoiler is inhibited aileron down aileron up roll spoilers up roll to the right only the down-going wing raises its spoilers
Chapter 15 · Flight Controls: Architecture and Control Laws
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
In roll, each wing has one aileron and four roll spoilers, numbers two to five. The ailerons travel twenty five degrees and the spoilers thirty five, although on some aircraft spoiler three is limited to seven degrees in roll. When the flaps are out, both ailerons droop five degrees. Watch a roll to the right, seen from behind: the right aileron goes up, the left one down, and on the right wing only, the down-going wing, the spoilers rise. On the left wing the spoilers stay flush. E L A C one normally controls the ailerons, with E L A C two as backup. If both are lost, the ailerons go to damping mode. Each aileron has two jacks, one working at a time, and damping is also selected if blue and green are both low. A failed S E C retracts its spoilers, a spoiler that loses hydraulics holds its position or less, and the symmetric spoiler is inhibited.
Yaw control
The rudder: mechanical pedals, electrical damping One rudder, moved by three servojacks (G, B, Y) in parallel Pedals: mechanical , two rigidly connected pairs Yaw damping and turn coordination: orders computed by the ELACs , sent to the FACs A green yaw damper actuator drives the jacks; the yellow one stays synchronised as backup No feedback to the pedals from yaw damping or turn coordinationfin rudder G B Y three servojacks in parallel yaw damper servo actuators G Y FAC 1 FAC 2 Pedals: direct mechanical control Yaw damping and turn coordination: ELAC → FAC no feedback to the pedals from yaw damping
Chapter 15 · Flight Controls: Architecture and Control Laws
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Yaw control is simpler. There is one rudder, moved by three independent servojacks working in parallel, one from each hydraulic system. The pedals are mechanical, with the captain and first officer pairs rigidly connected, so a push on the pedals moves the rudder directly. On top of that, yaw damping and turn coordination are automatic. The E L A Cs compute the yaw orders, and send them to the F A Cs, which drive the rudder through a yaw damper servo actuator. In automatic operation the green actuator drives all three jacks, while the yellow one stays synchronised and takes over if the green one fails. Here the rudder moves one way as if from the pedals, then the other way as if from the yaw damping. One important detail: none of this automatic movement is fed back to the pedals, so you will not feel your feet move.
Rudder travel limit and trim
Rudder travel limit and rudder trim Max rudder deflection reduces with speed to protect the structure; full pedal travel always available Limiter fails: limit frozen at the last value; full authority at slat extension Trim: two electric motors on the artificial feel unit; FAC 1 motor 1 , FAC 2 motor 2 standby RUD TRIM switch moves the neutral at 1°/s ; RESET returns it to zero at 1.5°/sWith the AP engaged the FMGC trims; switch and RESET inactive speed max rudder deflection low speed: full high speed: small Limiter failed: frozen at last value; full travel back at slat extension RUD TRIM L 0.8 RESET NOSE L NOSE R Rotary switch 1°/s · RESET to zero at 1.5°/s · both inactive with AP
Chapter 15 · Flight Controls: Architecture and Control Laws
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
As speed increases, the computers progressively reduce the maximum rudder deflection, to avoid excessive structural loads. Full pedal travel is always available, but except at low speed you reach the maximum rudder deflection before the end of pedal travel. If the travel limit system fails, the limit freezes at its last value, and full authority returns when the slats extend. In every case there is enough rudder for the whole envelope, including maximum asymmetric thrust. Rudder trim uses two electric motors that move the artificial feel unit: motor one, controlled by F A C one, does the work, and F A C two with motor two stays synchronised as a backup. The rotary switch on the pedestal moves the trim at one degree per second, and RESET returns it to zero at one and a half degrees per second. With the autopilot engaged, both are inactive.
Normal law
Normal law: three axes, protections, load alleviation TAKEOFF 70 kt lift-off pitch > 8° Pitch GROUND ROTATION (on some aircraft) blend 5 s FLIGHT MODE LANDING 50 ft touchdown +5 s and pitch < 2.5° Pitch FLIGHT MODE FLARE MODE: THS frozen, attitude memorised GROUND Lateral control: ground mode, then flight mode shortly after lift-off; flare uses the flight-mode lateral law; ground mode again after touchdown.
Chapter 15 · Flight Controls: Architecture and Control Laws
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Normal law gives three-axis control, flight envelope protection and alleviation of manoeuvre loads. The protections are there to help the pilot in an emergency, when only quick instinctive reactions will work. They are not structural limit protections, and they are not an invitation to leave the normal envelope deliberately. In pitch, normal law has several modes, shown on this timeline. On takeoff you start in ground mode. On some aircraft a rotation mode takes over from seventy knots. After lift-off, flight mode is blended in once the pitch attitude passes eight degrees. On landing, flight mode changes to flare mode at fifty feet, and ground mode returns five seconds after touchdown, once pitch is below two and a half degrees. Laterally, the aircraft simply goes from ground mode to flight mode shortly after lift-off, and back after touchdown.
Pitch: ground and rotation
Ground mode and rotation mode Ground mode: direct stick-to-elevator, no auto trim THS set automatically to 0° (green band) unless the crew sets a CG value, which has priority Takeoff roll: max up elevator 30° → 20° (on some aircraft depending on weight and CG) Rotation mode (some aircraft): pitch rate demand with tail strike protection , overridable Active from 70 kt until 10 s after lift-off with pitch above 8° GROUND MODE sidestick elevator direct: deflection ∝ stick · no auto trim THS set to 0° in the green band unless the crew sets a CG value Max elevator up during the takeoff roll 30° 20° reduced (some aircraft: by weight and CG) ROTATION MODE (on some aircraft) pitch rate demand law with tail strike protection uses pitch rate, tail clearance and stick position active from 70 kt until 10 s after lift-off and pitch > 8° the crew can override the tail strike protection
Chapter 15 · Flight Controls: Architecture and Control Laws
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the ground, the pitch law is a direct relationship: stick deflection gives a proportional elevator deflection, with no auto trim. The stabiliser is set automatically to zero, inside the green band, but if the crew has entered a value for the C G, that setting has priority for takeoff. During the takeoff roll, the maximum nose up elevator is reduced from thirty to twenty degrees, on some aircraft depending on weight and C G. Newer aircraft add a rotation mode. It is a pitch rate demand law that gives a consistent rotation for every weight, C G and configuration, while protecting against a tail strike, using the pitch rate, the tail clearance and the stick position. The crew can override it. It is active from seventy knots on the takeoff roll until ten seconds after lift-off, with the pitch attitude above eight degrees.
Pitch: flight mode
Flight mode: a load factor demand law Stick deflection = load factor demand , independent of speed Stick neutral, wings level: 1 g (corrected for pitch attitude): the flight path is held Automatic pitch trim , in manual flight and with the APNo trimming for speed or configuration changes Turns up to 33° bank: no pitch correction once established sidestick back load factor demanded 1 g 2.5 g same at any speed stick neutral: 1 g, path held Sidestick sets a load factor, not a surface angle Auto trim: no trimming for speed or configuration Up to 33° bank: no pitch correction once established
Chapter 15 · Flight Controls: Architecture and Control Laws
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
In flight mode, the sidestick does not command an elevator angle. It commands a load factor, proportional to stick deflection and independent of speed. With the stick at neutral and the wings level, the system holds one g, corrected for pitch attitude, so the flight path stays where you left it, and you never need to trim for a change of speed or configuration. If the aircraft drifts from the path you want, make small corrections, and if you sense you are over-controlling, simply let go of the stick. Pitch trim is automatic, both in manual flight and with the autopilot. Now watch the turn: the pilot rolls to thirty three degrees of bank and then releases the stick. The bank stays, and the system adds the extra load factor by itself, so no back pressure is needed once the turn is established.
Pitch: auto trim
When auto trim stops, and the autopilot Auto trim freezes : manual trim input, RA below 50 ft (100 ft with AP), load factor below 0.5 g , high speed protection α protection: THS limited to entry setting ↔ 3.5° nose down; no extra nose-up trim Above 1.25 g or 33° bank: THS limited to current ↔ 3.5° nose down AP engaged: ELACs and SECs limit AP orders ; all protections except pitch attitude remain AP disconnects with stick force, pedals 10° out of trim, or the trim wheel past a threshold Auto trim FREEZES when… 1 the crew moves the trim wheel 2 radio height < 50 ft (100 ft with AP) 3 load factor < 0.5 g 4 high speed / high Mach protection* THS travel is LIMITED when… α PROT active: between the entry setting and 3.5° nose down no further nose-up trim, by crew or system n > 1.25 g or bank > 33°: between the current setting and 3.5° nose down * on some aircraft the THS is instead limited between the entry setting and 11° nose up; some use 4° ND in α PROT
Chapter 15 · Flight Controls: Architecture and Control Laws
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Auto trim does not run all the time. It freezes when the crew makes a manual trim input, below fifty feet radio height, or one hundred feet with the autopilot engaged, when the load factor falls below half a g, and in high speed or high Mach protection. It is also limited. In angle of attack protection, the stabiliser can only move between the position it had on entering the protection and three and a half degrees nose down, so nobody, crew or system, can add nose up trim. Above one point two five g, or beyond thirty three degrees of bank, it is limited between its current setting and three and a half degrees nose down. On some aircraft the numbers differ slightly, as shown. With the autopilot engaged, the computers limit what it can order, and all normal law protections remain except pitch attitude protection.
Pitch: flare mode
Flare mode: the aircraft asks you to flare At 50 ft RA the THS freezes and flight mode changes to flare mode Flare mode: essentially direct stick-to-elevator, with some damping The attitude at 50 ft is memorised as the reference From 30 ft the reference is lowered to −2° over 8 s So a gentle nose-up input is needed to flare, like a conventional aircraft time pitch attitude 0° +2.5° −2° 50 ft 30 ft reference: −2° over 8 s pilot flares: gentle back stick At 50 ft RA: THS frozen, flare mode engages Attitude at 50 ft memorised as the reference From 30 ft: reference lowered to −2° over 8 s So the pilot must flare with a gentle nose-up input
Chapter 15 · Flight Controls: Architecture and Control Laws
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Close to the ground, a load factor law would hold the flight path all the way into the runway, which is not what you want for a landing. So as the aircraft passes fifty feet radio height, the stabiliser freezes and flight mode changes to flare mode. Flare mode is essentially a direct stick-to-elevator law, with a little damping from load factor and pitch rate feedback. The system memorises the attitude at fifty feet and uses it as the starting reference. Then, passing thirty feet, it starts lowering that reference towards minus two degrees, nose down, over eight seconds. The dashed red line on the graph is what the aircraft would do on its own. To flare, the pilot therefore makes a gentle nose-up input, the blue line, just as on a conventional aircraft. It feels natural, which is exactly the intention.
Lateral normal law
Lateral control: roll rate demand On the ground: stick drives aileron and roll spoiler deflection , gain varies with speed In flight: ailerons, spoilers 2–5 and rudder together (spoiler 1 is not used for roll) Roll rate proportional to stick, max 15°/s (7.5°/s in α or pitch protection, some aircraft) Turn coordination and dutch roll damping : no rudder needed in turns Stick neutral: bank held; bank limits come in the next lesson lateral stick roll rate demanded 15°/s 7.5°/s normal in α or pitch protection* In flight: ailerons, spoilers 2–5 and the rudder Turn coordination and dutch roll damping built in Stick neutral: bank held (up to 33°) On the ground: stick to surface, gain varies with speed * on some aircraft
Chapter 15 · Flight Controls: Architecture and Control Laws
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Laterally, on the ground the sidestick drives aileron and roll spoiler deflection directly, with a gain that depends on speed, while the pedals move the rudder through the mechanical linkage. Shortly after lift-off the lateral law blends into flight mode. Now the sidestick commands a roll rate, proportional to deflection, with a maximum of fifteen degrees per second at the stop. On newer aircraft that maximum halves to seven and a half degrees per second when angle of attack or pitch attitude protection is active. The law combines the ailerons, spoilers two to five and the rudder, which coordinates the turn and damps dutch roll, so you do not need your feet in a turn. With the stick at neutral, the bank angle is held. The flare uses the same lateral law, and after touchdown it returns to ground mode.
Normal law extras
Load alleviation and the sideslip target LAF (some aircraft): ailerons up for steady manoeuvres; ailerons + spoilers 4 and 5 for gustsReduces wing structure loads; clean configuration, normal law ; added to normal law orders Engine failure: the FAC shifts the sideslip indication to show the rudder for best climb Takeoff or go-around engine failure: the PFD sideslip index turns from yellow to blue Pilot centres the blue β target with rudder: ailerons neutral, spoilers retracted LOAD ALLEVIATION (on some aircraft) aileron up spoilers 4, 5 lift moves inboard: lower wing-root bending Steady manoeuvre: ailerons only Gust: ailerons + spoilers 4 and 5 Clean configuration, normal law SIDESLIP TARGET (engine failure) normal yellow index engine failure blue β target
Chapter 15 · Flight Controls: Architecture and Control Laws
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more functions belong to normal law. On some aircraft, the load alleviation function reduces the loads on the wing structure. It deflects the ailerons upwards during a steady manoeuvre, and the ailerons plus spoilers four and five when a gust is detected, moving the lift inboard and reducing the bending at the wing root. It works only in clean configuration and normal law, and its orders are simply added to the normal law orders. The second function is the sideslip target. If an engine fails, the F A C modifies the sideslip indication slightly, to show how much rudder gives the best climb performance, with ailerons neutral and spoilers retracted. After an engine failure at takeoff or go-around, the sideslip index on the PFD turns from yellow to blue, the beta target. The pilot's reaction is instinctive: centre it with rudder.
Sidesticks
Sidesticks and the priority logic Spring-loaded, not linked to each other, no feedback from the surfaces AP engaged: sticks locked at neutral; above 5 daN pitch or 3.5 daN roll they unlock and the AP disengages Both pilots move: inputs added (max one full deflection), green lights flash, "DUAL INPUT" Press and hold the takeover pb : priority, red arrow in front of the other pilot; 40 s latches it Last pilot to press has priority; a stick deactivated on the ground gives CONFIG L (R) SIDESTICK FAULT sidestick spring-loaded takeover pb radio PTT SIDE STICK PRIORITY CAPT F/O Capt has priority: green (F/O stick not neutral) F/O lost authority: red arrow Both sticks moved: inputs added, limited to one full deflection Green lights flash + "DUAL INPUT" Hold the takeover pb: priority + "PRIORITY LEFT / RIGHT" Held 40 s: the other stick stays off until a pb is pressed
Chapter 15 · Flight Controls: Architecture and Control Laws
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The two sidesticks are spring-loaded to neutral, not mechanically linked, and get no feedback from the surfaces. With the autopilot engaged they are locked at neutral. Push harder than about five decanewtons in pitch or three and a half in roll, and the stick unlocks, the autopilot disengages and the AUTO FLT AP OFF alert comes on, although that is not the recommended way to disconnect. Only one pilot should fly at a time. If both move their sticks, the inputs are added algebraically, limited to one full deflection, the green priority lights flash, and you hear DUAL INPUT. To take control, press and hold the takeover button. You hear PRIORITY LEFT or PRIORITY RIGHT, and a red arrow lights in front of the pilot who lost authority. Hold it forty seconds and the other stick stays deactivated until either button is pressed again. On the ground, after the first engine start, both sidestick positions also show in white on the PFDs.
Reconfiguration
When the system degrades: alternate, direct, mechanical NORMAL LAW 120 140 160 pitch scale: green = speed scale: VLS (amber strip) V α PROT (amber/black) V α MAX (red) all protections available ALTERNATE LAW 120 140 160 pitch scale: × amber X speed scale: VLS (amber strip) stall warning red/black barber pole protections lost auto trim kept DIRECT LAW 120 140 160 pitch scale: × amber X speed scale: VLS (amber strip) stall warning red/black barber pole USE MAN PITCH TRIM ECAM: FLT CTL ALTN LAW (PROT LOST) · FLT CTL DIRECT LAW (PROT LOST) + MAN PITCH TRIM USE · MAX SPEED 320 kt
Chapter 15 · Flight Controls: Architecture and Control Laws
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Depending on the failures in the flight control system or its sensors, there are three levels of reconfiguration: alternate law, which comes with or without reduced protections, then direct law, and finally the mechanical backup. The crew is told in two places. The ECAM shows FLT CTL ALTN LAW, protections lost, with a maximum speed of three hundred and twenty knots, or FLT CTL DIRECT LAW, with three hundred and twenty knots or Mach point seven seven, and MAN PITCH TRIM USE. And the PFD tells you at a glance. In normal law you see green double bars on the pitch scale and the alpha protection and alpha max strips on the speed scale. When protections are lost, amber crosses replace the green bars and a red and black barber pole marks the stall warning. When auto trim is lost, USE MAN PITCH TRIM appears in amber below the F M A.
Alternate law
Alternate law Pitch: load factor demand with auto trim, like normal law; ground mode 5 s after touchdown Reduced protections: load factor limit ; low speed stability (nose-down, overridable) and high speed stability (nose-up above VMO/MMO) No pitch attitude or bank protection; α floor inoperative ; stall warning: crickets, "STALL", red STALL STALL Roll: direct · yaw: alternate (yaw damping only, ±5°) or mechanical Landing gear down : pitch goes to direct law for the flare. Without reduced protection: load factor limit onlyALTERNATE LAW: what changes Pitch load factor demand, auto trim Protections reduced: load factor only, plus low and high speed STABILITY Roll DIRECT (no bank protection) Yaw alternate: yaw damper only, ±5° α floor inoperative At landing gear DOWN ALTN flight mode L/G down DIRECT law (flare) pitch becomes direct stick-to-elevator ground mode 5 s after touchdown No L/G data (LGCIU 1+2 or 3 SEC lost): slats or flaps ≥ 2 instead
Chapter 15 · Flight Controls: Architecture and Control Laws
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
In alternate law, pitch is still a load factor demand law with auto trim, but with reduced protections. The load factor limit stays as in normal law. Angle of attack protection is replaced by low speed stability: from about five to ten knots above the stall warning speed, a gentle nose-down demand tries to stop the speed decaying, and the pilot can override it. Above V M O or M M O, high speed stability adds a nose-up demand, again overridable. There is no pitch attitude or bank protection, alpha floor is inoperative, and there is a conventional stall warning: crickets, the STALL voice and a red STALL message. Roll becomes direct, and yaw becomes alternate, with yaw damping only, limited to five degrees. When the gear goes down, pitch reverts to direct law for the flare. Alternate law without reduced protection keeps only the load factor limit.
Pitch: elevator deflection proportional to stick ; max deflection depends on CG No auto trim : amber USE MAN PITCH TRIM on the PFDNo protections , α floor inoperative; overspeed and stall warnings availableRoll direct: about 30°/s clean, 25°/s slats out, using ailerons and spoilers 4 and 5 Yaw mechanical : pedals only, no yaw damper, no turn coordination DIRECT LAW stick surface position max elevator deflection set by CG · manual trim Max roll rate ≈ 30°/s clean ≈ 25°/s slats out Roll surfaces used 1 2 3 4 5 R AIL Spoiler 4 failed: spoiler 3 replaces it Ailerons failed: all roll spoilers used Yaw: pedals only, no yaw damper, no turn coordination USE MAN PITCH TRIM
Chapter 15 · Flight Controls: Architecture and Control Laws
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Direct law is the lowest electrical law. In pitch, elevator deflection is simply proportional to stick deflection. The maximum deflection is set according to the C G, a compromise between enough authority with a forward C G and a control that is not too sensitive with an aft C G. There is no auto trim, so the pilot trims manually, prompted by USE MAN PITCH TRIM in amber on the PFD. There are no protections and alpha floor is inoperative, but the overspeed and stall warnings remain, as in alternate law. In roll, stick position gives surface position, with gains set by the slat and flap configuration. The roll rate is about thirty degrees per second clean, and twenty five with the slats extended, using only the ailerons and spoilers four and five. Yaw is mechanical: no yaw damping, no turn coordination.
Reconfiguration
Which failures cause which law Failure Pitch law Protections Roll Yaw ELAC 1 + 2 (or both ailerons) ALTN reduced DIRECT ALTN SEC 1 + 2 + 3 ALTN reduced DIRECT ALTN HYD green + yellow ALTN reduced DIRECT MECH HYD green + blue ALTN none DIRECT ALTN SFCC 1 + 2 (slat channel) ALTN none DIRECT ALTN ADR 1 + 2 + 3 ALTN none DIRECT MECH IR 1 + 2 + 3 DIRECT none DIRECT MECH Both radio altimeters, at gear extension DIRECT none DIRECT ALTN
Also ALTN with reduced protections: one elevator, all spoilers, THS jam, one sidestick, EMER GEN and BAT ONLY (yaw mechanical). Two FACs: on some aircraft ALTN reduced, on newer ones normal law kept with ALTN LAW indicated.
Chapter 15 · Flight Controls: Architecture and Control Laws
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a selection from the reconfiguration table that examiners like. Lose both E L A Cs, or all three S E Cs, and you get alternate law with reduced protections, roll direct and yaw alternate. Green plus yellow hydraulic failure gives alternate with reduced protections, but yaw mechanical. Green plus blue gives alternate without protections. So does a double slat channel failure of the S F C Cs. Three A D Rs lost: alternate law, no protections, yaw mechanical. Three I Rs lost is worse: direct law straight away. And losing both radio altimeters gives direct law when the gear is extended. The caption adds several more alternate law cases, including one elevator, all spoilers, a stabiliser jam, a sidestick, and the electrical emergency configurations. Notice the pattern: the more sensors or computers you lose, the lower the law.
Abnormal attitude law
Abnormal attitude law Engages far outside the envelope: bank > 125° , pitch > 50° up or < 30° down Or speed < 70–90 kt or > 440 kt , Mach > 0.91 , angle of attack > 40° Engaged: pitch alternate without protection (no load factor limit), roll direct, yaw mechanical, no auto trim ECAM F/CTL DIRECT LAW , PFD USE MAN PITCH TRIM After recovery: pitch ALTN without reduced protection, roll direct, yaw alternate, F/CTL ALTN LAW for the rest of the flight Abnormal attitude law engages if… 0° 125° 125° bank > 125° (shaded) pitch > 50° up or < 30° down speed < 70–90 kt or > 440 kt Mach > 0.91 α > 40° While engaged After recovery (rest of flight) pitch ALTN, no protection roll direct, yaw mechanical no auto trim ECAM: F/CTL DIRECT LAW pitch ALTN without reduced protections roll direct, yaw alternate ECAM: F/CTL ALTN LAW
Chapter 15 · Flight Controls: Architecture and Control Laws
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
If, for any reason, the aircraft goes far outside the normal envelope and reaches an extreme attitude, an abnormal attitude law engages, to give the pilot maximum efficiency to recover. The triggers are a bank angle above one hundred and twenty five degrees, pitch above fifty degrees nose up or thirty degrees nose down, speed below seventy to ninety knots depending on attitude, or above four hundred and forty knots, Mach above point nine one, or angle of attack above forty degrees. While it is engaged, pitch is alternate law with no protection at all, not even the load factor limit, roll is direct, yaw is mechanical, and there is no auto trim. The ECAM shows F/CTL DIRECT LAW. Once the aircraft is back inside the envelope, you keep alternate law without reduced protection, roll direct and yaw alternate, for the rest of the flight.
Mechanical backup
Mechanical backup Purpose: meet the safety objectives in MMEL dispatch conditions Covers a temporary total electrical loss , or the temporary loss of five fly-by-wire computers Also the loss of both elevators , or of all ailerons and spoilers Pitch: manual THS trim wheel ; PFDs show red MAN PITCH TRIM ONLY Lateral: rudder pedals MECHANICAL BACKUP trim wheel mechanical link to THS PITCH: THS by manual trim wheel LATERAL: rudder pedals MAN PITCH TRIM ONLY red message on both PFDs a temporary means, to keep control until systems recover
Chapter 15 · Flight Controls: Architecture and Control Laws
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
The last level is the mechanical backup. Its purpose is to meet the safety objectives when the aircraft is dispatched under the minimum equipment list. It covers a temporary total loss of electrical power, the temporary loss of all five E L A Cs and S E Cs, the loss of both elevators, or the total loss of ailerons and spoilers. In pitch, the pilot controls the aircraft with the stabiliser, using the manual trim wheel, and both PFDs display MAN PITCH TRIM ONLY in red. Laterally, the pilot uses the rudder pedals, which move the rudder through the mechanical linkage. This is why the stabiliser and the rudder keep a mechanical path. Think of it as a way to keep the aircraft under control for a while, until the electrical systems or computers recover, not as a way to fly an approach.
Summary
Flight controls architecture in one page Computers 2 ELAC (elevators, THS, ailerons), 3 SEC (spoilers, standby pitch), 2 FAC (rudder). FCDCs feed the ECAM.
Surfaces All electrical, all hydraulic. THS and rudder also mechanical. Pitch: ELAC 2 → ELAC 1 → SEC.
Normal law Ground, (rotation), flight (load factor demand, auto trim), flare from 50 ft. Roll rate demand, max 15°/s.
Sidesticks Inputs added on dual input. Takeover pb: priority; 40 s latches. AP off above 5 daN pitch / 3.5 daN roll.
Degraded laws ALTN: reduced protections, roll direct, direct at gear down. DIRECT: no auto trim. Abnormal attitude.
Mechanical THS by trim wheel (MAN PITCH TRIM ONLY, red) and rudder by pedals.
Chapter 15 · Flight Controls: Architecture and Control Laws
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it all together. Seven computers: two E L A Cs for the elevators, stabiliser and ailerons, three S E Cs for the spoilers and standby pitch, two F A Cs for the rudder, plus the data concentrators for the ECAM. Every surface is signalled electrically and moved hydraulically, and the stabiliser and rudder keep a mechanical path. Pitch passes from E L A C two to E L A C one to a S E C. Normal law runs from ground mode, through rotation on newer aircraft, to the load factor demand flight mode with auto trim, and to flare mode at fifty feet. Laterally it is a roll rate demand. On dual input the sticks add up, and the takeover button gives priority. Alternate law keeps reduced protections with roll direct and becomes direct at gear down; direct law has no auto trim; and the last resort is the trim wheel and the pedals.