A320 Aircraft Systems · Chapter 18
Fuel Controls, Indications and Quantity The FUEL overhead panel, the refuel panel, the fuel quantity indicating and level sensing systems, and every symbol, colour and memo on the ECAM fuel displays.
ENG 1 ENG 2 APU X FEED OPEN ON L TK PUMPS 1 2 R TK PUMPS 1 2 CTR TK PUMP 1 CTR TK PUMP 2 MODE SEL ACT FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT MAN FAULT FWD A U T O A U T O F U E L FUEL 1 2 1350 1370 F.USED 1+2 2720 KG APU 690 5430 3200 5430 690 -12 -8 °C -8 -12 °C F.FLOW 1+2 : 42 KG/MIN FOB : 15440 KG © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the last lesson we followed the fuel from the tanks to the engines. Now we sit in the cockpit and look at how the crew controls and monitors all of it. We start with how the aircraft measures its fuel: the quantity indicating computer and the level sensors. Then we go through every pushbutton on the FUEL overhead panel and exactly when its FAULT light comes on. Next comes the ECAM fuel page, symbol by symbol, the fuel on board figure and the memos, with some worked examples of failures. Finally we visit the refuel control panel that the ground crew, and sometimes you, will use. This lesson is all about reading the cockpit correctly.
Fuel controls
Our route through ATA 28-10-80 and 28-20 ENG 1 ENG 2 APU X FEED OPEN ON L TK PUMPS 1 2 R TK PUMPS 1 2 CTR TK PUMP 1 CTR TK PUMP 2 MODE SEL ACT FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT MAN FAULT FWD A U T O A U T O F U E L Measuring The FQI computer, probes, densitometer, and the level sensing unit.
FUEL panel Tank pumps, centre pumps or transfer valves, MODE SEL, X FEED, ACT.
ECAM The FUEL page, FOB on the upper display, memos and advisories.
Refuel panel Quantity windows, HI LVL lights, valves, preselector and BATT POWER.
Chapter 18 · Fuel Controls, Indications and Quantity
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the controls and indications of the fuel system. First, measuring: how the fuel quantity indicating computer works out the mass of fuel in each tank, and how separate level sensors give the warnings and drive the automatic transfers. Second, the FUEL overhead panel that you see here, with its tank pump buttons, the centre tank buttons, the mode selector, the crossfeed button and the A C T button. For each one we will learn what turns its FAULT light on. Third, the ECAM: the fuel system page, the fuel on board figure on the upper display, the memos and the advisories, with some worked failure examples. And finally the refuel control panel, under the wing.
Fuel quantity indication
The FQI system A computer that sends total fuel mass , and each tank's quantity and temperature , to the ECAM It also controls automatic refuelling Two channels : channel 2 takes over automatically if channel 1 failsCapacitance probes in each tank measure level and temperatureA densitometer (cadensicon) in each inner tank; a CIC gives the fuel's dielectric constant if it fails Tank indicators and the preselector on the refuel panel densitometer capacitance probes FQI computer 2 channels ECAM mass = volume × density
Chapter 18 · Fuel Controls, Indications and Quantity
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The aircraft does not just measure how full each tank is; it works out the mass of fuel, which is what matters for performance. The fuel quantity indicating system, or F Q I, is a computer with two channels. If channel one fails, channel two takes over automatically. Watch the tank fill: inside each tank a set of capacitance probes senses the fuel level, and also its temperature. Volume alone is not enough, so a densitometer, called a cadensicon, sits in each inner tank to measure the fuel's properties. If it fails, a capacitance index compensator gives the fuel's dielectric constant instead. The computer then sends the total fuel mass, and each tank's quantity and temperature, to the ECAM. It also drives the indicators on the refuel panel and controls automatic refuelling.
FQI after take-off (some aircraft)
Why FOB can dip after take-off With low fuel loads (up to 7 t ), the inner tank readings fluctuate after take-off Pitch and acceleration move the fuel in the tank FOB reads low for about 2 min , then recovers, accurate about 6 min later in the climb Up to 400 kg ; EFOB on the MCDU may turn amber; go-around: under 300 kg Higher loads: FOB may read up to 1 t high , back to accurate within 6 min -400 -200 0 +200 +400 0 2 4 6 8 10 minutes after take-off (illustration) indicated FOB minus actual, kg about 2 min about 6 min later up to 400 kg low Low fuel loads (up to 7 t), some aircraft; go-around: under 300 kg
Chapter 18 · Fuel Controls, Indications and Quantity
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a behaviour that surprises crews on some aircraft. With a low fuel load, up to about seven tonnes, the inner tank quantity indications fluctuate after take-off. The reason is physical: the high pitch angle and the acceleration move the fuel within the tank, so the probes see a distorted surface. The fuel on board figure falls for about two minutes, then increases again, and comes back to the accurate value about six minutes later, during the climb. The error can reach four hundred kilograms, and the estimated fuel on board on the MCDU may turn amber for a while. After a go-around the fluctuation stays under three hundred kilograms. With higher fuel loads, the indication may instead rise by up to one tonne, again recovering within six minutes. So do not react to a dip in the first minutes.
Level sensing
The fuel level sensing control unit The FLSCU uses level sensors for high , low and overflow levels, plus a temperature sensor It switches the refuel and defuel functions It controls the IDG cooling recirculation It controls the centre to wing (and ACT ) transfer systems Below 750 kg in a wing tank, the low-level sensor gives the LO LVL warning, independent of the FQI high level underfull low level 750 kg LO LVL on ECAM separate from the FQI
Chapter 18 · Fuel Controls, Indications and Quantity
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Alongside the quantity system there is a second, independent set of sensors, run by the fuel level sensing control unit, the F L S C U. It uses level sensors that detect high, low and overflow levels, and a fuel temperature sensor. With these it switches the refuelling and defuelling functions, controls the generator cooling recirculation, and controls the centre to wing tank transfer, and on aircraft with additional tanks, the A C T transfer too. Watch the level fall: the underfull sensor goes dry first, then, at about seven hundred and fifty kilograms in a wing tank, the low level sensor goes dry and triggers the LO LVL warning on the ECAM. That warning is totally independent of the quantity the FQI displays. So even if the gauge is wrong, the low level warning is still trustworthy.
FUEL overhead panel
The FUEL panel ENG 1 ENG 2 APU X FEED OPEN ON L TK PUMPS 1 2 R TK PUMPS 1 2 CTR TK PUMP 1 CTR TK PUMP 2 MODE SEL ACT FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT MAN FAULT FWD A U T O A U T O F U E L 1 4 2 3 2 1 5 ① tank pumps · ② centre tank pumps · ③ MODE SEL · ④ ACT · ⑤ X FEED. Normal: all lights out.
Chapter 18 · Fuel Controls, Indications and Quantity
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the FUEL panel on the overhead, drawn for the version with centre tank pumps. Read it as a picture of the system. At the bottom left are the two left tank pumps, and at the bottom right the two right tank pumps. In the middle are centre tank pump one and centre tank pump two, with the mode selector between them. To the left of the centre pumps is the A C T pushbutton, for aircraft with additional centre tanks. Above, the white mimic lines join the left pumps and centre pump one to engine one, and the right pumps and centre pump two to engine two. The APU branch comes off the left side. And on the line between the two sides sits the crossfeed pushbutton. In normal operation every light on this panel is out.
L (R) TK PUMPS pb
Wing tank pump pushbuttons On (lights out): the pump runsOFF : pump off, white OFF lightAmber FAULT + ECAM caution when the delivery pressure drops FAULT does not come on with OFF selected Six-pump version: an ON wing pump only feeds when the centre pump pressure drops below the threshold L (R) TK PUMPS 1 (2) FAULT OFF ON all lights out FAULT OFF OFF white OFF FAULT OFF FAULT pressure low FAULT (amber) + ECAM caution: delivery pressure drops FAULT does not come on when OFF is selected Six-pump version: a wing pump that is on only feeds when centre pump pressure is too low
Chapter 18 · Fuel Controls, Indications and Quantity
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The four wing tank pump buttons all work the same way. Pressed in, with all lights out, the pump is on. Released, the pump is off and the white OFF light comes on. The amber FAULT light, together with an ECAM caution, means that the pump's delivery pressure has dropped. Notice the detail: the FAULT light does not come on when OFF is selected, so switching a failed pump off clears the light. On the version with centre tank pumps, remember from the last lesson that a wing pump can be on and running without actually delivering fuel. It only feeds when the delivery pressure of the centre pumps drops below the threshold of its sequence valve. So a running wing pump with no flow during centre feeding is completely normal.
CTR TK PUMP pb
Centre tank pump pushbuttons On : in AUTO the MODE SEL logic controls the pump; in MAN it simply runsOFF : pump off, white OFF lightAmber FAULT + ECAM caution: the pump is in operation and its delivery pressure drops A pump stopped by the automatic logic does not show FAULT CTR TK PUMP 1 (2) FAULT OFF ON AUTO or MAN FAULT OFF OFF pump off FAULT OFF FAULT running, low press ON: controlled by the MODE SEL logic in AUTO, runs continuously in MAN FAULT + ECAM caution: the pump is in operation and its delivery pressure drops A pump stopped by the AUTO logic gives no FAULT
Chapter 18 · Fuel Controls, Indications and Quantity
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The two centre tank pump buttons look the same as the wing pump buttons, but the on position means something slightly different. With the button on and the mode selector in AUTO, the pump is controlled automatically by the logic we learned: two minutes at engine start, then slats retracted, stopping when the inner tank is full and five minutes after low level. With the mode selector in MAN, an on pump simply runs. Selecting OFF stops the pump and lights the white OFF. The amber FAULT light, with an ECAM caution, comes on when the pump is in operation and its delivery pressure drops. So a centre pump that the logic has stopped normally, for example because the inner tank is full, does not give you a FAULT. It is just resting.
MODE SEL pb
The mode selector AUTO : centre pumps run 2 min at engine start, then with slats retracted ; stop 5 min after centre low levelMAN : the crew controls the centre pumps with their pushbuttonsAmber FAULT + caution: centre tank more than 250 kg and left or right wing tank less than 5 000 kg In MAN the crew must switch the centre pumps OFF when the centre tank is empty MODE SEL FAULT MAN AUTO all lights out FAULT MAN MAN crew controls FAULT MAN FAULT centre fuel unused FAULT (amber) + ECAM caution when: centre tank more than 250 kg AND left OR right wing tank less than 5 000 kg Meaning: wing fuel is being burnt while the centre tank still holds fuel
Chapter 18 · Fuel Controls, Indications and Quantity
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The mode selector chooses who controls the centre tank pumps. In AUTO, which is the normal position with all lights out, the system controls them: two minutes at engine start, then whenever the slats are retracted, and stopping five minutes after the centre tank reaches low level. In MAN, the white MAN light comes on and the crew controls the pumps with their own pushbuttons. Now the FAULT light, which is an exam favourite. It comes on in amber, with an ECAM caution, when the centre tank still has more than two hundred and fifty kilograms while the left or the right wing tank has less than five thousand kilograms. In plain words: the engines are burning wing fuel while the centre tank still has fuel in it. And remember that in MAN, the crew must switch the centre pumps off when the centre tank is empty.
Worked examples
Will the MODE SEL FAULT light come on? Centre (kg) Left wing (kg) Right wing (kg) MODE SEL Why 2 400 4 800 4 900 FAULT centre > 250 and a wing < 5 000 200 4 800 4 800 no light centre only 200 kg 3 000 5 400 5 400 no light both wings at 5 000 kg or more 800 5 100 4 950 FAULT centre > 250 and a wing < 5 000
Rule: centre > 250 kg AND (left < 5 000 kg OR right < 5 000 kg). One wing below 5 000 kg is enough.
Chapter 18 · Fuel Controls, Indications and Quantity
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us practise the rule with four cases. In the first, the centre tank has two thousand four hundred kilograms and both wings are below five thousand. Centre fuel is being left behind, so the FAULT light comes on. In the second, the wings are just as low but the centre tank has only two hundred kilograms, which is not more than two hundred and fifty, so there is no light. That is a normal end of centre feeding. In the third, the centre has three thousand but both wings are at five thousand four hundred, so nothing is wrong yet. In the fourth, the centre has eight hundred, the left wing is above five thousand, but the right wing has fallen to four thousand nine hundred and fifty. One wing is enough, so the FAULT light comes on.
Some aircraft: CTR TK L (R) XFR pb
Centre transfer valve pushbuttons On aircraft with jet pump transfer , CTR TK L XFR and R XFR replace the centre pump buttons On: valve automatic in AUTO; open in MAN · OFF: valve closed FAULT + caution: the associated wing tank overflows MODE SEL AUTO: valves open if the wing tank is not full ; stop 5 min after centre low level MODE SEL FAULT: same 250 kg / 5 000 kg rule, with the MODE SEL at AUTO ENG 1 ENG 2 APU X FEED OPEN ON L TK PUMPS 1 2 R TK PUMPS 1 2 CTR TK L XFR CTR TK R XFR MODE SEL ACT FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT OFF FAULT MAN FAULT FWD A U T O A U T O F U E L FAULT OFF ON auto / open in MAN FAULT OFF OFF valve closed FAULT OFF FAULT wing tank overflow CTR TK L (R) XFR: controls a centre transfer valve AUTO: opens if its wing tank is not full Stops 5 min after the centre tank low level FAULT + caution: the associated wing tank overflows
Chapter 18 · Fuel Controls, Indications and Quantity
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
On aircraft without centre tank pumps, the panel looks almost the same, but the two centre buttons are labelled C T R T K L X F R and R X F R, because they control the centre tank transfer valves instead of pumps. With a button on and the mode selector in AUTO, the valve is controlled automatically: it opens when its wing tank is not full, and transfer stops five minutes after the centre tank reaches low level. In MAN, an on button opens the valve. OFF closes it. The FAULT light, here on the right button, with an ECAM caution, means that the associated wing tank has overflowed. The mode selector FAULT uses the same rule as before, more than two hundred and fifty kilograms in the centre and less than five thousand in a wing, but only with the selector at AUTO.
X FEED pb
The crossfeed pushbutton ON : the valve opens; the ON legend comes on white OPEN (green) when the valve is fully open OFF : the valve closes; no lightMemo FUEL X FEED : green when the pb is ON and the valve is not fully closed The memo turns amber in flight phases 3, 4 and 5 X FEED OPEN ON OFF valve closed OPEN ON ON valve moving OPEN ON ON + OPEN fully open ON (white): the valve is commanded open OPEN (green): the valve is fully open Memo FUEL X FEED: green when ON and the valve is not fully closed; amber in phases 3, 4, 5
Chapter 18 · Fuel Controls, Indications and Quantity
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The crossfeed button controls the single crossfeed valve. Normally it is off, the valve is closed, and the button shows no light. Press it, and the valve is commanded open: the white ON legend comes on straight away. The upper green OPEN legend only appears once the valve is fully open, so for a moment you may see ON alone while the motors drive the valve. Press it again and the valve closes. On the upper ECAM display, the memo FUEL X FEED appears whenever the button is on and the valve is not fully closed. It is green, but it turns amber during flight phases three, four and five, which cover the take-off, so that the crew does not take off with the crossfeed open without noticing.
AUTO : forward transfer needs flight, slats retracted, an ACT low-level sensor wet, centre high-level sensor dry for 10 minStops as soon as one condition is lost FWD : opens the ACT transfer valve and the ACT 1 or ACT 2 inlet valve, then runs the ACT transfer pump FAULT + caution (pb at AUTO): centre < 3 000 kg and an ACT > 250 kg No ACT installed: the pushbutton is inoperative ACT FAULT FWD AUTO auto transfer FAULT FWD FWD manual transfer FAULT FWD FAULT ACT fuel left FWD: opens the ACT transfer valve and an inlet valve, then runs the ACT transfer pump FAULT + caution (pb at AUTO): centre tank less than 3 000 kg and an ACT more than 250 kg With no ACT installed, the pb is inoperative
Chapter 18 · Fuel Controls, Indications and Quantity
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A C T button controls the transfer from the additional centre tanks. In AUTO, the forward transfer happens by itself when four conditions are all true: the aircraft is in flight, the slats are retracted, at least one A C T low level sensor is wet, meaning there is fuel to move, and the centre tank high level sensor has been dry for at least ten minutes, meaning there is room for it. As soon as one condition is lost, the transfer stops. Selecting FWD starts a manual transfer: the A C T transfer valve and an inlet valve open, and the A C T transfer pump runs. The FAULT light comes on, with the button at AUTO, when the centre tank has less than three thousand kilograms while an A C T still has more than two hundred and fifty.
ECAM FUEL page
The ECAM FUEL page FUEL 1 2 1350 1370 F.USED 1+2 2720 KG APU 690 5430 3200 5430 690 -12 -8 °C -8 -12 °C 1200 900 F.FLOW 1+2 : 42 KG/MIN FOB : 15440 KG TAT -28 °C SAT -52 °C 10 H 42 GW 64500 KG 1 Engine numbers and fuel used (F.USED) 2 Engine LP valves 3 Crossfeed valve 4 APU feed indication 5 Wing and centre tank pumps 6 Tank quantities 7 Outer to inner transfer triangle 8 Fuel temperatures 9 ACT quantities and transfer 10 Total fuel flow and fuel on board 1 2 3 4 5 6 7 8 9 10
Chapter 18 · Fuel Controls, Indications and Quantity
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the ECAM fuel system page in cruise. Like the panel, it is laid out like the system. At the top are the engine numbers with the fuel used by each engine, and in the middle the total fuel used. Below each engine number is its L P valve. Between them is the crossfeed valve, and on the left the APU feed indication. The row of small boxes are the pumps: two for each wing and two for the centre. Under them, the tank outline shows the quantity in each outer, inner and centre tank, with the outer to inner transfer triangles and the fuel temperatures. If additional centre tanks are fitted, their quantities appear below. At the bottom are the total fuel flow and the fuel on board. Let us read these items one group at a time.
FUEL page: pumps and valves
Pump and valve symbols Pump in line green : pressure normal · LO amber : low pressure · cross line amber : contactor off Centre pump cross line green : off because auto shut-off is required (normal) LP valve: in line green open · in line amber : open with ENG MASTER OFF · cross line amber: closed X FEED: cross line green closed · in line green open · amber when it disagrees with the pb Diagonal amber : valve in transitECAM FUEL page symbols Tank pump normal LO low press contactor off Centre pump off, auto stop off, not auto LP valve open open, master OFF closed in transit X FEED closed open open, pb off closed, pb ON
Chapter 18 · Fuel Controls, Indications and Quantity
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The symbols follow a simple philosophy: green means the state is normal or expected, amber means something needs your attention. A pump box with a green line through it, in line, means normal pressure. Amber LO means the pump contactor is on but pressure is low. An amber cross line means the contactor is off. Centre pumps have one extra case: a green cross line means the pump is off because the automatic logic wants it off, which is normal; an amber cross line means it is off when it should not be. For the L P valve, in line green is open, in line amber is open even though the engine master switch is off, and an amber cross line is closed. The crossfeed is green when it agrees with its button, and amber when it disagrees.
FUEL page: quantities and temperatures
Quantities, boxes and pulsing Quantities normally green ; two dashes on the last digits when the FQI is inaccurate Outer boxed amber : both transfer valves failed to open at inner low level Centre boxed amber : both centre pumps failed or OFF (or both centre transfer valves failed closed) Inner amber : that wing overflowed · wing figures pulse if the wings differ by > 1 500 kg (phases 2 and 6) Temperature advisory (phases 2 and 6): inner > 45 °C , outer > 55 °C , or < −40 °C ; amber + caution beyond the limits FUEL 1 2 1350 1370 F.USED 1+2 2720 KG APU 690 4210 3200 2600 690 -12 -8 °C -8 -12 °C F.FLOW 1+2 : 42 KG/MIN FOB : 8190 KG Left wing heavier by more than 1 500 kg: its figures pulse Right outer boxed amber, triangle solid amber
Chapter 18 · Fuel Controls, Indications and Quantity
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The tank quantities are normally green. When the quantity system is inaccurate, two dashes appear across the last two digits. An amber box around a quantity means that fuel cannot be used. Around an outer tank, both transfer valves have failed to open when the inner reached low level, as on the right outer here. Around the centre tank, both centre pumps have failed or are switched off, or, on aircraft with transfer valves, both have failed closed. An inner tank figure turning amber means that wing has overflowed. In flight phases two and six, if the two wings differ by more than one thousand five hundred kilograms, the heavier wing's figures pulse, as the left wing does here. Temperatures appear when their sensor is wet, with an advisory above forty five degrees inner, fifty five outer, or below minus forty.
Worked example
Reading boxed quantities FUEL 1 2 1350 1370 F.USED 1+2 2720 KG APU LO LO 690 5430 2400 5430 690 -12 -8 °C -8 -12 °C F.FLOW 1+2 : 42 KG/MIN FOB : 15440 KG FUEL 1 2 7050 7090 F.USED 1+2 14140 KG APU 0 640 0 650 0 -12 -8 °C -8 -12 °C F.FLOW 1+2 : 40 KG/MIN FOB : 1290 KG Both centre pumps failed: centre boxed amber, FOB half-boxed Late in the flight: outer fuel transferred, centre pumps auto-off A green cross line on a centre pump is normal; amber LO with a boxed quantity is not.
Chapter 18 · Fuel Controls, Indications and Quantity
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Compare these two pages. On the left, in cruise, both centre tank pumps show amber LO: they are running, but delivering no pressure. Two thousand four hundred kilograms remain in the centre, and because there is no gravity feeding from the centre tank, that fuel is now unusable. So the centre quantity is boxed in amber, and the fuel on board figure gets an amber half box, telling you that not all of the fuel on board can be used. On the right, late in a normal flight, the centre tank is empty and its pumps show green cross lines, because the automatic logic has switched them off as required. The inner tanks have reached low level, the transfer triangles are green, and the outer tanks have drained to zero. Nothing amber, nothing wrong.
FUEL page: FOB, flow, used, ACT
FOB, fuel used, fuel flow and ACTs FOB : total of all tanks, including ACTs; amber half box if not all of it is usableF.USED : green from phase 2 until power is cut; reset at engine start on the ground Engine number amber when that engine is below idle , white at or above idle F.FLOW : total flow per minute; amber XX if the data is invalidACT quantity in a grey box , amber on a transfer fault; triangle outline = auto transfer, solid = manual FUEL 1 2 1350 0 F.USED 1+2 1350 KG APU 690 5430 3200 5430 690 -12 -8 °C -8 -12 °C 2100 1500 F.FLOW 1+2 : XX KG/MIN FOB : 15440 KG FOB half-boxed and dashed · engine 2 number amber F.FLOW amber XX · ACT boxes amber: transfer fault
Chapter 18 · Fuel Controls, Indications and Quantity
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
At the bottom of the page is the fuel on board, the total of all tanks including the A C Ts. It is normally green. An amber half box means that some of that total is not usable, for example because the centre pumps have failed, the outer transfer valves did not open, or an A C T cannot transfer. Two dashes on the last digits mean the quantity system is degraded. The fuel used figures are green from flight phase two until electrical power is cut at the end of the flight, and they reset when an engine is started on the ground. An engine number turns amber when that engine is below idle. Fuel flow is shown per minute, replaced by an amber X X if the data is invalid. A C T quantities sit in grey boxes, which turn amber on a transfer fault.
Degraded FQI
How far off can FOB be? Two dashes across the last two digits of FOB: the FQI has lost its normal mode. Call the FUEL page to see which tank.
Tank(s) in degraded mode Inner and outer cell aircraft Single wing tank aircraft Wing outer tank +20 kg / −200 kg — Wing inner tank (or wing tank) ± 110 kg +130 kg / −310 kg Centre tank ± 130 kg ± 130 kg All tanks +390 kg / −750 kg +390 kg / −750 kg
Worked example: FOB 6 400 kg, all tanks degraded: the real figure lies between 5 650 kg and 6 790 kg.
Chapter 18 · Fuel Controls, Indications and Quantity
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the fuel on board figure shows two dashes across its last two digits, the quantity system is in a degraded mode. Call up the fuel page on the lower ECAM to see which tank is affected, because the size of the possible error depends on it. On aircraft with inner and outer cells, an outer tank can read up to twenty kilograms high or two hundred low; an inner tank, plus or minus one hundred and ten; the centre, plus or minus one hundred and thirty. If all tanks are affected, the indication can be up to three hundred and ninety kilograms high or seven hundred and fifty kilograms low. So with six thousand four hundred indicated and every tank degraded, the true figure could be anywhere from five thousand six hundred and fifty to six thousand seven hundred and ninety kilograms. Plan with the low end.
FUEL page: transfer and APU
Transfer triangles and the APU indication Transfer triangle green : outer to inner transfer in progress Solid amber : valves open although commanded closed · amber outline : a valve in transitNo triangle: valves closed · XX : position unknown APU white, green triangle : APU fuel valve open APU and solid triangle amber : valve open with the APU FIRE pb out or MASTER SW off Transfer triangle (outer to inner) green: transfer to the inner tank solid amber: valves open, commanded closed amber: a valve in transit XX valve position not available nothing shown: valves closed APU indication APU white, green triangle: APU valve open APU amber, solid triangle: open, but FIRE pb out or MASTER OFF APU amber only: valve position disagrees APU white, white triangle: APU valve closed
Chapter 18 · Fuel Controls, Indications and Quantity
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two smaller items complete the page. Next to each outer tank figure there is a triangle that tells you about the outer to inner transfer valves. Nothing shown means the valves are closed, which is normal for most of the flight. A green triangle means a transfer to the inner tank is in progress. A solid amber triangle means the valves are open although they are commanded closed, and an amber outline means a valve is in transit. X X means the valve position is unknown. On the left is the APU fuel indication. White APU with a green triangle means the APU fuel valve is open. If the valve is open while the APU fire button is out, or the APU master switch is off, both turn amber. Amber APU with no triangle shows a valve that does not agree with what was commanded.
Upper ECAM display
FOB and the fuel memos FOB also appears on the upper display (E/WD)CTR TK FEEDG : at least one centre tank pump energisedOUTR TK FUEL XFRD : at least one outer transfer valve openREFUELG : refuel panel door open, or the cockpit refuel PWR pb ONFUEL X FEED : green; amber in phases 3, 4, 5 Single wing tank aircraft: FOB BELOW 3T when either wing has less than 1 500 kg N1 % FF 1 260 1 270 KG/H FOB : 15440 KG CTR TK FEEDG OUTR TK FUEL XFRD REFUELG FUEL X FEED FUEL X FEED (phases 3, 4, 5) Memos shown together here for learning; in service only the relevant ones appear
Chapter 18 · Fuel Controls, Indications and Quantity
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The upper ECAM display carries the fuel on board figure below the engine indications, so you always have it in view. Its half box and dashes mean the same as on the fuel page. The memo area then tells you what the fuel system is doing. C T R T K F E E D G, centre tank feeding, appears in green when at least one centre tank pump is energised. Outer tank fuel transferred appears when at least one transfer valve is open. REFUELG appears when the refuel panel door is open, or the cockpit refuel power button is on. FUEL X FEED appears when the crossfeed is selected and the valve is not closed; green normally, amber in phases three, four and five. Aircraft with single wing tanks also have FOB BELOW 3T, when either wing holds less than fifteen hundred kilograms.
Worked example
The fuel imbalance advisory Advisory in phases 2 and 6 when the wings differ by more than 1 500 kg The heavier wing's inner and outer figures pulse Example: left 4 910 + 690 = 5 600 kg , right 3 210 + 690 = 3 900 kg Difference 1 700 kg > 1 500 kg: the left wing figures pulse At 1 400 kg difference there is no advisory FUEL 1 2 1350 1370 F.USED 1+2 2720 KG APU 690 4910 3200 3210 690 -12 -8 °C -8 -12 °C F.FLOW 1+2 : 42 KG/MIN FOB : 12700 KG Left 5 600 kg, right 3 900 kg: difference 1 700 kg More than 1 500 kg in phase 6: the left wing figures pulse
Chapter 18 · Fuel Controls, Indications and Quantity
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us work through an imbalance. In cruise, the left inner tank shows four thousand nine hundred and ten and the left outer six hundred and ninety, so the left wing holds five thousand six hundred kilograms. The right inner shows three thousand two hundred and ten, with six hundred and ninety in the outer, so the lighter right wing holds three thousand nine hundred. The difference is one thousand seven hundred kilograms. That is more than fifteen hundred, and we are in phase six, so the system gives an advisory, and the figures of the heavier wing, here the left one, pulse. If the difference were only one thousand four hundred kilograms, there would be no advisory at all. Whatever the cause, the crew then follows the procedure, which is outside this lesson.
Refuel control panel
The refuel control panel FUEL QTY (kg × 1000) LEFT 3.25 CTR 0.00 RIGHT 3.20 HI LVL LEFT CTR RIGHT REFUEL VALVES OPEN NORM SHUT OPEN NORM SHUT OPEN NORM SHUT MODE SELECT REFUEL OFF DEFUEL XFR OPEN TEST HI LVL LTS BATT POWER ON NORM PRESELECTED 18.5 DEC INC CKPT ACTUAL 18.4 END 1 Fuel quantity in each tank 2 HI LVL lights (blue): valve closes 3 REFUEL VALVES: OPEN / NORM / SHUT 4 MODE SELECT: REFUEL / OFF / DEFUEL XFR 5 OPEN light (amber): defuel valve open 6 TEST: HI LVL or LTS 7 BATT POWER toggle 8 PRESELECTED, ACTUAL and END 1 2 3 4 5 6 7 8 Located on the fuselage beneath the right wing, or under a wing next to the refuel coupling.
Chapter 18 · Fuel Controls, Indications and Quantity
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the refuel control panel, which the refuelling crew uses outside the aircraft. At the top, three windows show the fuel quantity in each tank, in thousands of kilograms or pounds. Below them are three blue high level lights. When the system detects a high fuel level in a tank, its light comes on and that tank's refuel valve closes automatically. Then come the three refuel valve switches, guarded in NORM, where the automatic logic controls the valves. The mode select switch, guarded at OFF, chooses refuel or defuel transfer, and the amber OPEN light next to it shows that the defuel transfer valve is open. There is a test switch, a battery power toggle, and at the bottom the preselected and actual displays, with the END light.
Refuel control panel
Refuel panel controls and lights Item What it does REFUEL VALVES (guarded NORM) NORM: automatic · OPEN: open in REFUEL or DEFUEL XFR, each closes at high level · SHUT: closed MODE SELECT (guarded OFF) OFF: de-energised, valves closed · REFUEL: auto or manual · DEFUEL XFR: transfer valve opens TEST HI LVL: lights come on if sensors serviceable (go out if tanks already full) · LTS: all lights and 8s PRESELECTED / ACTUAL Preselected total (×1 000) set with DEC / INC · actual fuel on board END light (green) Steady: automatic refuelling complete · flashing: refuelling aborted · CKPT light: not used BATT POWER toggle ON (momentary): HOT BUS 1 powers the FQI, about 40 s of tests; cut after 10 min unused or at the end
Chapter 18 · Fuel Controls, Indications and Quantity
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the details of each control. The refuel valve switches are guarded in NORM for automatic control. OPEN opens the valves when the mode switch is at refuel or defuel transfer, although each still closes at high level, and SHUT closes them. The mode switch is guarded at OFF, where the system is de-energised. The test switch has two positions: high level tests the high level sensors, and lights tests every light and shows all eights on the displays. The preselected display is set with the decrease and increase switch. The green END light is steady when automatic refuelling is complete and flashes if it was aborted. And with no aircraft power, a momentary battery power switch connects hot bus one to the quantity system; after about forty seconds of tests the indications appear.
Summary
Fuel controls and indications in one page Measuring FQI: 2 channels, probes, densitometer, CIC; mass to ECAM. FLSCU: high, low, overflow sensors; LO LVL at 750 kg, independent.
Pump pbs FAULT + caution on low delivery pressure; never with OFF; centre: only when running.
MODE SEL AUTO / MAN; FAULT: centre over 250 kg and a wing under 5 000 kg.
X FEED and ACT ON white, OPEN green; memo amber in phases 3 to 5. ACT FAULT: centre under 3 t, ACT over 250 kg.
FUEL page Green normal, amber attention; boxed = unusable; half-boxed FOB; dashes = degraded; pulse = imbalance over 1 500 kg.
Refuel panel HI LVL blue, OPEN amber, END green; BATT POWER uses HOT BUS 1.
Chapter 18 · Fuel Controls, Indications and Quantity
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us wrap up. The quantity system works out mass with two channels, probes and a densitometer, while the level sensing unit gives independent signals, including the LO LVL warning at seven hundred and fifty kilograms. On the panel, a pump FAULT means low delivery pressure, never just because it is off, and for a centre pump only while it is running. The mode selector FAULT means more than two hundred and fifty kilograms in the centre with a wing below five thousand. The crossfeed shows white ON and green OPEN, and its memo turns amber in phases three to five. On the fuel page, green is normal and amber needs attention: boxed means unusable, a half box on FOB means not all usable, dashes mean degraded, and pulsing means an imbalance. Next time you sit in the simulator, read the fuel page aloud.