A320 Aircraft Systems · Chapter 7
AP/FD Lateral and Vertical Modes Every autopilot and flight director mode: heading, NAV and localizer; climb, descent, altitude, vertical speed, expedite and TCAS; takeoff, approach and go-around; and the reversions that catch pilots out.
SPEED G/S LOC CAT 3 DUAL AP1+2 1 FD 2 A/THR © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to lesson seven. Last time we met the flight control unit, the flight directors and the autopilots. Now we learn what they actually do: the guidance modes. We begin with the golden rule that links the pitch modes to the autothrust. Then the lateral modes: heading, NAV and the localizer. Then the vertical modes, one by one: managed and open climb and descent, expedite, altitude capture and hold, vertical speed, and on some aircraft the TCAS mode. After that the common modes that work on both axes at once: takeoff, the ILS approach and autoland, the non precision approach and the go-around. We finish with mode reversions and speed protection, the automatic changes that you must spot on the FMA before they surprise you.
Guidance modes
Our route through the AP/FD modes SPEED G/S* ALT LOC CAT 3 DUAL RADIO 100AP1+2 1 FD 2 A/THR The rules Managed and selected, how to engage, and pitch versus autothrust.
Lateral HDG/TRK, preset, NAV and the LOC pb.
Vertical CLB, OP CLB, DES, OP DES, EXPED, ALT, V/S and TCAS.
Common modes Takeoff, ILS and autoland, non precision, go-around, reversions.
Chapter 7 · AP/FD Lateral and Vertical Modes
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan. We start with three rules that apply to every mode: what is managed and what is selected, how you arm and engage a mode, and how the pitch mode decides what the autothrust does. Next the lateral modes: heading and track, the heading preset at takeoff and go-around, NAV, and the localizer button. Then the vertical modes, which take most of our time, because that is where the A320 most often surprises new pilots. After that the common modes, which work on both axes together: takeoff, the ILS and automatic landing, the non precision approach and the go-around. And finally mode reversions and speed protection. Keep an FMA in your mind all the way through: every mode we meet has its own words in a particular column.
Two families
Managed and selected modes Axis Managed (targets from the FMGS) Selected (targets from the FCU) Lateral NAV, APP NAV · LOC*, LOC · RWY, RWY TRK · GA TRK · ROLL OUT HDG, TRK Vertical SRS (takeoff and go-around) · CLB, DES · ALT CST*, ALT CST · ALT CRZ · G/S*, G/S · FINAL, FINAL APP · FLARE · TCAS (if installed) OP CLB, OP DES · V/S, FPA · ALT*, ALT · EXPED (if installed) Speed FMGC reference: ECON, AUTO SPD, SPD LIM, constraints · EXPED FCU reference Basic modes none HDG-V/S or TRK-FPA: what the AP/FD falls back to
Chapter 7 · AP/FD Lateral and Vertical Modes
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every AP and FD mode belongs to one of two families. Managed modes follow the lateral flight plan, the vertical profile and the speed profile that the flight management part has worked out from what you put into the MCDU. Selected modes follow the targets you set in the FCU windows. Laterally, everything is managed except heading and track. Vertically, the managed modes are the ones that respect the flight plan constraints, such as climb, descent and the constraint altitude modes, plus the takeoff, approach and landing modes. The selected vertical modes are the open modes, vertical speed and flight path angle, altitude capture and hold, and expedite. Heading with vertical speed, or track with flight path angle, are called the basic modes, because they are what the system falls back to when anything else is lost.
Mode selection
How modes are armed and engaged Takeoff : thrust levers to TO or FLX engage the managed modesPush a knob: arm or engage the managed modePull a knob: engage the selected modeDIR TO on the MCDU: inserts a direct leg, engages or keeps NAV APPR pb : LOC and G/S, or APP NAV and FINAL · LOC pb : localizer onlySPD MACH --- HDG TRK LAT --- HDG V/S TRK FPA ALT 29000 LVL/CH V/S FPA ----- SPD MACH LOC HDG V/S TRK FPA AP 1 AP 2 A/THR 100 1000 EXPED METRIC ALT UP DN PUSH TO LEVEL OFF APPR FCU Takeoff levers to TO or FLX: managed SRS and RWY engage Push a knob managed mode: HDG → NAV, ALT → CLB or DES Pull a knob engage the selected mode on the window value DIR TO on the MCDU inserts a direct leg; engages or keeps NAV APPR pb LOC + G/S, or APP NAV + FINAL (per F-PLN) LOC pb localizer only
Chapter 7 · AP/FD Lateral and Vertical Modes
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are only a few ways to change mode, and you should know them cold. On the runway, setting the thrust levers to the TO or FLX detent engages the managed takeoff modes. In flight, you push a knob to arm or engage its managed mode, and you pull a knob to engage the selected mode on the value in its window. On the MCDU, a DIR TO inserts a direct leg in the flight plan and engages NAV, or keeps it engaged. For approaches you have two buttons. The APPR button arms the localizer and glideslope for an ILS, or APP NAV and FINAL for a non precision approach, depending on which approach is in the flight plan. The LOC button arms only the localizer, which is what you use for a localizer-only approach.
The golden rule
Pitch mode decides the autothrust mode Pitch flies the SPEED so the A/THR holds a fixed THRUST Pitch flies the PATH so the A/THR holds the SPEED / MACH • OP CLB · CLB · EXP CLB → THR CLB • OP DES · EXP DES · DES (idle path) → THR IDLE • SRS (takeoff, go-around) • FLARE in autoland → RETARD (idle) • V/S · FPA • ALT* · ALT · ALT CST* · ALT CST · ALT CRZ • DES on a geometric path • G/S* · G/S · FINAL · FINAL APP • TCAS (if installed) • No AP and no FD at all speed held by the elevator speed held by the engines AP/FD and A/THR can never both control the speed at the same time: the pitch mode you choose decides what the autothrust does
Chapter 7 · AP/FD Lateral and Vertical Modes
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the most important idea in the whole auto flight system. Speed can be held either by the elevator or by the engines, but never by both at once. So the pitch mode you choose decides what the autothrust must do. If the pitch mode is flying the speed, as in open climb, managed climb, open descent, an idle descent, expedite or SRS, then the autothrust simply sets a fixed thrust: climb thrust going up, idle going down. If the pitch mode is flying a path, as in vertical speed, flight path angle, altitude hold, a geometric descent, the glideslope or FINAL, then the autothrust holds the speed. And if there is no autopilot and no flight director at all, the autothrust holds the speed too. In autoland, the flare comes with the autothrust in RETARD. Learn this table and the FMA will always make sense.
Lateral: HDG/TRK
Heading and track: the basic lateral mode Flies the heading or track in the FCU window Engaged by pulling the knob, not sooner than 5 s after lift-off Also engages when NAV, APP NAV, FINAL APP, LOC is lost And at AP/FD engagement with no other mode Disengaged only by another lateral mode Go-around below 100 ft in HDG: HDG stays (later standards) HDG / TRK: the basic lateral mode 0 3 6 9 12 15 18 21 24 27 30 33 selected heading 090 • Pull the HDG/TRK knob not sooner than 5 s after lift-off • NAV, APP NAV or FINAL APP lost flight plan lost or a discontinuity entered • LOC or LOC* lost • AP/FD engaged with no other mode basic mode at engagement • LOC pb pressed in APP NAV or FINAL APP
Chapter 7 · AP/FD Lateral and Vertical Modes
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Heading and track are the selected lateral modes, and also the basic lateral mode. The aircraft flies whatever heading or track is in the FCU window, chosen with the HDG V S, TRK FPA button. You engage it by turning the knob and pulling, but not sooner than five seconds after lift off. It also engages by itself whenever a managed lateral mode disappears: when NAV, APP NAV or FINAL APP are lost because the flight plan is lost or you enter a discontinuity, when the localizer mode is lost, when you engage an autopilot or flight director with nothing else active, and when you press the LOC button while in APP NAV or FINAL APP. Only another lateral mode will disengage it. When AP and FD are lost, the window simply shows the aircraft current heading.
Lateral: HDG/TRK preset
Presetting a heading for takeoff or go-around Turn the HDG knob before 30 ft on takeoff: value stays in the window NAV disarms ; at 30 ft RWY TRK until you pull Go-around: preset possible in LOC*, LOC, LAND or GA Passing the MAP the window resynchronises (later standards) Cancel: DIR TO , push the knob, or AP/FD off HDG preset for takeoff 30 ft RA turn HDG knob before 30 ft NAV disarms RWY TRK until the knob is pulled pull: HDG MAN FLX +58 SRS CLB RWY 1 FD 2 A/THR • Go-around: preset available in LOC*, LOC, LAND or GA; pull to turn • Passing the missed approach point the window synchronises; preset lost • Cancel a preset: DIR TO, push the HDG knob (arms NAV), or AP/FD off • No preset at takeoff: NAV armed on the ground, engages at 30 ft
Chapter 7 · AP/FD Lateral and Vertical Modes
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes ATC wants a heading straight after takeoff instead of the departure route. For that the system has a heading preset. Before takeoff, or up to thirty feet, you turn the heading knob to the new value, and it stays in the window instead of going back to dashes. NAV is disarmed straight away. At thirty feet the FMA shows RWY TRK, and the aircraft keeps the runway track until you pull the knob, when it turns to your preset heading. The same works on a missed approach: whenever LOC star, LOC, LAND or the go-around mode is engaged, you can preset a heading and pull it when you need it. On later standards, overflying the missed approach point resynchronises the window and ends the preset. To cancel a preset, use DIR TO, push the knob to arm NAV, or switch the AP and FD off.
Lateral: NAV
NAV: following the flight plan Managed, aims for zero cross-track error ; needs a lateral F-PLN Armed: on the ground (no preset), push HDG knob, APPR for non-ILS, go-around Engages: 30 ft after takeoff, DIR TO , push within ~1 NM of the leg, or capture of the leg Armed NAV captures only if the track line meets the leg before the TO waypoint Lost with the F-PLN or at a discontinuity No NAV: no CLB/DES , constraints ignored NAV: armed, then capture of the active leg WPT1 WPT2 WPT3 INTCP track line intercepts before the TO waypoint (white) SPEED ALT HDG NAV AP1 1 FD 2 A/THR
Chapter 7 · AP/FD Lateral and Vertical Modes
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
NAV is the managed lateral mode. It steers along the flight plan with the aim of zero cross track error. It arms on the ground when no heading is preset, when you push the heading knob in flight, when you press APPR for a non ILS approach, and at a go-around unless a heading was preset. It engages at thirty feet after takeoff, at a DIR TO, when you push the knob within about one nautical mile of the active leg, or by itself when an armed NAV reaches the capture zone. Here is the classic trap. Armed NAV only captures if your track line crosses the active leg before the TO waypoint, the one shown in white, and the intercept point is shown on the ND. And remember the vertical link: without NAV, managed climb and descent are not available and all the flight plan constraints are ignored.
Lateral: LOC pb
The localizer on its own For a localizer-only approach, or to intercept the glideslope from above Arms with an ILS tuned , above 400 ft RA , not in TO or GA Disarmed by the LOC pb again, NAV armed or GA ; DIR TO does not disarm it Engages automatically when capture conditions are met LOC pb again when engaged: HDG/TRK on the current value LOC pb: localizer on its own Arms when • an ILS is tuned (frequency and course) • above 400 ft RA • TO or GA mode not engaged use it for a LOC-only approach, or to intercept the glideslope from above Disarms • LOC pb pressed again • NAV armed • GA engaged • (DIR TO does not disarm LOC) Disengages • another lateral mode engages • LOC pb pressed again: HDG/TRK on the current value SPEED ALT LOC* CAT 1 AP1 1 FD 2 A/THR
Chapter 7 · AP/FD Lateral and Vertical Modes
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The LOC button captures and tracks the localizer beam without the glideslope. You use it for a localizer-only approach, and also to start an ILS when you must intercept the glideslope from above, because you can join the localizer first and arm the glideslope later. It arms if an ILS is tuned with both frequency and course, the aircraft is above four hundred feet radio height, and neither takeoff nor go-around mode is engaged. It is disarmed by pressing the button again, by arming NAV, or by a go-around. Note that a DIR TO engages NAV but does not disarm the localizer. Once armed, LOC star and LOC engage by themselves. And if you press the button again with the localizer engaged, the aircraft reverts to heading or track on its present value.
Vertical: principles
How you leave a level First turn the ALT knob to the new altitude Pull ALT: OP CLB / OP DES (selected)Push ALT: CLB / DES (managed, needs NAV)Or set a V/S and pull the V/S knob · or push EXPED Every one of these arms ALT on the new level Leaving a level: first set the new altitude, then… SPD MACH --- HDG TRK LAT --- HDG V/S TRK FPA ALT 31000 LVL/CH V/S FPA ----- SPD MACH LOC HDG V/S TRK FPA AP 1 AP 2 A/THR 100 1000 EXPED METRIC ALT UP DN PUSH TO LEVEL OFF APPR FCU Pull ALT knob OP CLB / OP DES constraints ignored Push ALT knob CLB / DES constraints respected Set V/S, pull V/S knob V/S (FPA) selected rate Push EXPED EXP CLB / DES steepest (if installed) Each of these arms ALT on the new FCU altitude
Chapter 7 · AP/FD Lateral and Vertical Modes
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every change of level on the A320 follows the same two steps. First you turn the altitude knob to the new cleared altitude. Turning alone does nothing to the flight path. Then you tell the system how to get there. Pull the altitude knob and you get open climb or open descent: a selected mode that goes straight to your altitude and ignores the flight plan constraints. Push it and you get managed climb or descent, which respects the constraints, but needs NAV to be engaged. Or set a vertical speed and pull the vertical speed knob. Or, on aircraft that have it, push EXPED for the steepest gradient. Whichever you choose, ALT is armed on the new level, so the aircraft will capture and hold it. Students often forget step one and wonder why nothing happens.
Vertical: CLB
Managed climb Climbs to the FCU altitude respecting altitude constraints Needs NAV , flight over 5 s, not in DES/APPR/GA phase Pitch holds speed; A/THR THR CLB Armed on the ground if ACC ALT is below the FCU and constraint altitudes Speed is not changed to meet a constraint: it may be predicted missed NAV lost: OP CLB with a triple click · FCU set below: V/S Managed climb with an altitude constraint FCU 15 000 ft WPT at or below 7 000 CLB ALT CST CLB 1 climbing to the constraint THR CLB CLB ALT NAV AP1 1 FD 2 A/THR 2 level at the constraint, CLB armed SPEED ALT CST CLB NAV AP1 1 FD 2 A/THR ALT magenta: next level-off is a constraint speed is not changed to meet a constraint
Chapter 7 · AP/FD Lateral and Vertical Modes
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
CLB is the managed climb. It takes you to the FCU altitude while respecting the altitude constraints at the waypoints, and the speed constraints too if the speed is managed. The elevator flies the speed and the autothrust gives climb thrust. CLB can be armed on the ground or in SRS if the acceleration altitude is below both the FCU altitude and the lowest constraint, and it then engages at the acceleration altitude. In flight it needs NAV. Watch the picture: at the constraint the aircraft levels in ALT CST with CLB armed in blue, and climbs again after the waypoint. ALT on the FMA is magenta when the next level off is a constraint, blue when it is the FCU altitude. One subtlety: the system will not change speed to make a constraint. If it predicts a miss, you must select a speed yourself.
Vertical: OP CLB
Open climb Selected : pitch holds speed, A/THR CLB thrust Goes straight to the FCU altitude, ignoring all constraints Pull the ALT knob (flight > 5 s, not in LAND, FCU above) Also: SPD pulled in TOGA or EXP CLB, ACC ALT without NAV, speed protection, NAV lost in CLB Small change: under 1 200 ft climbs at about 1 000 ft/min FCU set below the aircraft: V/S on the current rate Open climb: straight to the FCU altitude FCU 15 000 ft constraint ignored OP CLB THR CLB OP CLB ALT NAV AP1 1 FD 2 A/THR • Pull ALT knob (FCU altitude above), or pull SPD in TOGA or EXP CLB • ACC ALT reached with CLB armed but no NAV • NAV lost while in CLB (triple click) • Small change under 1 200 ft: about 1 000 ft/min
Chapter 7 · AP/FD Lateral and Vertical Modes
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Open climb is the selected climb. The elevator holds the speed, selected or managed, while the autothrust gives maximum climb thrust, and the aircraft goes straight up to the FCU altitude, ignoring every constraint on the way. You normally engage it by pulling the altitude knob, with the FCU altitude above you, once you have been airborne five seconds and as long as LAND is not engaged. It also appears on its own in a few cases: if you pull the speed knob in TOGA or expedite climb, if the acceleration altitude is reached with CLB armed but no NAV, as a speed protection reversion, and, most important, if NAV is lost while you are in CLB. That last one comes with a triple click. For small level changes, under twelve hundred feet, the aircraft climbs gently at about one thousand feet per minute.
Vertical: DES
The managed descent profile T/D repressurisation segment (if needed) IDLE segment pitch holds speed, A/THR at idle geometric pitch holds path, A/THR speed FL130 at 9 000 at 3 000 at DECEL VAPP by 1 000 ft 120 NM 100 NM 80 NM 60 NM 40 NM 20 NM 0 NM Computed backwards from the deceleration point · wind and constraints included · holds not included Idle path: pitch holds speed, A/THR idle. Geometric path: pitch holds the path, A/THR holds speed. Default cabin rate −350 ft/min.
Chapter 7 · AP/FD Lateral and Vertical Modes
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The managed descent follows a profile that the FMGS builds backwards, from the deceleration point to the top of descent, so that you reach VAPP at one thousand feet on the final path. From the top of descent it first puts an idle segment, down to the first constraint that cannot be flown at idle; on that segment the elevator holds the speed and the autothrust sits at idle. Then come geometric segments between the constraints, where the elevator follows the path and the autothrust holds the speed. If needed there is also a repressurisation segment at the top, worked out from the destination elevation and the cabin rate, which is minus three hundred and fifty feet per minute unless you change it. The profile includes the forecast winds but not holding patterns, and changing the cost index or a constraint can turn a geometric segment into an idle one.
Vertical: DES guidance
Flying and monitoring the managed descent No automatic descent at T/D: set altitude, push ALT Before T/D: constant V/S to join the path · after T/D: idle Above the path: speed rises to the top of the range; MORE DRAG → ½ speedbrake Below the path: target speed held at −1 000 ft/min (−500 low down) Hold: DES flies −1 000 ft/min within constraints TOO STEEP PATH : not flyable even with ½ speedbrakeMonitoring the managed descent profile above: speed rises to the top of the range, then path is lost MORE DRAG: ½ speedbrake below: target speed held, −1 000 ft/min (−500 when low) Start the descent set the cleared altitude and push ALT: before T/D a gentle V/S, after T/D idle VDEV deviation on the PFD altitude scale and on the PROG page Hold DES flies −1 000 ft/min, never below the next constraint or FCU altitude TOO STEEP PATH segment impossible even with half speedbrakes; no predictions there
Chapter 7 · AP/FD Lateral and Vertical Modes
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The aircraft never starts down by itself at the top of descent. You set the cleared altitude and push the altitude knob. If you are early, it descends at a constant vertical speed until it joins the profile; at or beyond the top of descent it goes to idle. During the descent watch the vertical deviation on the PFD altitude scale. Above the profile, the speed is allowed to rise to the top of the managed speed range, then the aircraft leaves the path, and MORE DRAG asks you for half speedbrakes. Below the profile, it holds the target speed at minus one thousand feet per minute, or minus five hundred lower down, until it rejoins. In a hold, DES flies minus one thousand feet per minute but never below the next constraint or the FCU altitude. And a too steep path is a segment that even half speedbrakes cannot fly.
Vertical: OP DES and EXPED
Open descent and expedite OP DES : pull ALT, pitch holds speed, A/THR IDLE , constraints ignoredFCU set above the aircraft: V/S , box; triple click if not confirmed in 5 s EXPED (if installed): maximum gradient; needs managed speedEXP CLB : green dot, CLB thrust · EXP DES : M .80 / 340 kt , idleEXPED ignores SPD/ALT constraints and SPD LIM Ends at ALT* , or by pulling ALT, SPD or V/S, or pushing ALT OP DES (selected) • pull the ALT knob, FCU altitude below • pitch holds the speed (selected or managed) • A/THR at IDLE thrust • all altitude constraints ignored • FCU altitude set above: V/S engages, box, triple click if not confirmed THR IDLE OP DES ALT HDG AP1 1 FD 2 A/THR EXPED (if installed) • push EXPED: climb or descent with maximum gradient • EXP CLB: green dot speed, CLB thrust • EXP DES: M .80 / 340 kt, IDLE thrust • ignores SPD and ALT constraints and SPD LIM • ends at ALT*, or pull ALT, SPD or V/S knob, push ALT THR IDLE EXP DES ALT HDG AP1 1 FD 2 A/THR
Chapter 7 · AP/FD Lateral and Vertical Modes
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Open descent is the mirror of open climb. You pull the altitude knob with the FCU altitude below you; the elevator holds the speed and the autothrust sets idle, and every altitude constraint is ignored on the way down. If you then set an FCU altitude above the aircraft, the descent makes no sense any more, so vertical speed engages on the current rate and the mode is boxed; if you do not confirm with another action within five seconds, you get a triple click. Expedite, fitted on some aircraft, is an open mode for the steepest gradient. In climb it targets green dot with climb thrust; in descent Mach point eight zero or three hundred and forty knots at idle. It ignores the speed and altitude constraints and the speed limit, and ends at altitude capture or when you choose another mode.
Vertical: ALT* and ALT
Altitude capture and hold ALT arms when heading for a level ≥ 250 ft away: blue (FCU) or magenta (constraint)ALT* in the capture zone; ALT within 20 ft ALT* inhibited 3 s after an FCU change, and below 400 ft in TO or GA FCU changed by more than 250 ft in ALT*: V/S on current rate ALT holds the altitude memorised at engagement ALT CRZ : soft altitude, ±50 ft at the cruise levelCapturing and holding an altitude FCU 10 000 ft OP CLB ALT* capture zone ALT within 20 ft ALT arms whenever climbing or descending towards a level 250 ft or more away ALT* inhibits for 3 s after an FCU change; not below 400 ft in TO or GA ALT* lost FCU altitude changed by more than 250 ft: V/S on current rate ALT holds the altitude memorised at engagement, even if the baro setting changes ALT CRZ soft altitude at the cruise level: ±50 ft for a steady Mach
Chapter 7 · AP/FD Lateral and Vertical Modes
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
ALT arms automatically whenever you climb or descend towards a level at least two hundred and fifty feet away: blue on the FMA for the FCU altitude, magenta for a constraint. As you approach, ALT star or ALT CST star engages in a capture zone that depends on your vertical speed, and the capture flies its own vertical speed that shrinks with the remaining height. Within twenty feet, ALT or ALT CST takes over. Capture cannot engage for three seconds after you change the FCU altitude, nor below four hundred feet in takeoff or go-around. The big trap: change the FCU altitude by more than two hundred and fifty feet during ALT star, and vertical speed engages on the current rate, so the aircraft keeps climbing or descending. At the cruise level the soft altitude mode, ALT CRZ, allows fifty feet either way to hold the Mach smoothly.
Vertical: V/S and FPA
Vertical speed and flight path angle Selected basic mode: holds the V/S or FPA in the FCU window A/THR in SPEED/MACH ; V/S has priority over speed At VLS or VMAX the V/S is reduced: FMA boxed amber , value pulses Reversion target: the current V/S, or the preselected one if turned within 45 s Ends at the FCU altitude, at G/S* , by ALT knob, EXPED or go-around V/S protection: speed comes first at the limits SPEED V/S+2500 ALT NAV AP1 1 FD 2 A/THR too much V/S in climb: speed decays to VLS, V/S reduced, amber box Engage pull V/S knob (5 s after lift-off), push for V/S = 0, or AP/FD on with no mode Reversions to V/S ALT* with FCU change > 250 ft; FCU altitude crosses the aircraft in CLB/DES/OP/EXP Automatic 5 s after lift-off with no mode; loss of G/S, FINAL, LOC, NAV in DES, or profile A/THR SPEED or MACH; V/S has priority until VLS or VMAX Ends pull or push ALT, EXPED, go-around, FCU altitude reached, G/S*
Chapter 7 · AP/FD Lateral and Vertical Modes
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Vertical speed and flight path angle are the selected basic vertical modes. You pull the knob, at least five seconds after lift off, or push it for an immediate level off; and they also engage on their own: five seconds after lift off with no other vertical mode, on loss of the glideslope, FINAL, the localizer, NAV in DES or the descent profile, and in the reversions we saw. The autothrust holds the speed, and the vertical speed has priority. If you ask for too much, the aircraft accelerates or decelerates to hold it, until the speed reaches VLS or VMAX. Then the autopilot reduces the vertical speed to protect the speed, the FMA vertical speed is boxed in flashing amber and the value pulses. The mode ends when the FCU altitude is reached, at glideslope capture, or when you choose another mode.
Vertical: TCAS mode
AP/FD TCAS mode (on some aircraft) TA : TCAS arms (blue, line 3) · RA : TCAS engages, even with AP and FD offCorrective RA: V/S target 200 ft/min into the green; A/THR to SPEED Speed kept between VLS − 5 and VMAX ; G/S or FINAL disengage, LOC or NAV stay Clear of conflict : V/S, ALT* or ALT; ALT or ALT CRZ armedInhibited below 900 ft RA , in TA mode, or with EGPWS, windshear or stall warning AP/FD TCAS mode (on some aircraft) 0 target 200 ft/min into the green V/S scale SPEED TCAS ALT NAV AP1 1 FD 2 A/THR A/THR goes to SPEED/MACH speed kept between VLS − 5 and VMAX Alpha floor inhibited while levers stay in CL G/S or FINAL disengage · LOC or NAV stay TA TCAS armed: blue, FMA line 3 RA TCAS engages, even with AP and FD off (FD bars appear) Clear of conflict V/S, ALT* or ALT; ALT armed; triple click if V/S Corrective RA exit ±1 000 ft/min (+500 if at or above 30 000 ft climbing) Inhibited below 900 ft RA, TA mode, EGPWS, windshear or stall warning
Chapter 7 · AP/FD Lateral and Vertical Modes
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
On aircraft fitted with it, the TCAS mode lets the autopilot or flight director fly a resolution advisory. When a traffic advisory comes, TCAS is armed and shown in blue. When a resolution advisory comes, the TCAS mode engages, even if both autopilots and flight directors were off, in which case the bars appear and heading engages. For a corrective advisory the target is two hundred feet per minute beyond the edge of the red zone on the vertical speed scale. The autothrust goes to speed mode, and the speed is kept between VLS minus five and VMAX. A glideslope or FINAL mode disengages, but the localizer or NAV stays. At clear of conflict, vertical speed, altitude capture or altitude hold engages, with ALT armed, so you return towards the FCU altitude. It is inhibited below nine hundred feet, in TA mode, and with an EGPWS, windshear or stall warning.
Common modes: takeoff
SRS and runway modes Levers to TOGA or FLX : SRS + RWY engage if V2 inserted, slats out , on ground 30 s SRS: V2 + 10 ; engine failure: higher of V2 or current, max V2 + 15 Pitch limit 18° (22.5° windshear), at least 120 ft/min SRS ends at ACC ALT , ALT* above 400 ft, or SPD pulled → OP CLB RWY : LOC within ½ dot and 20°; NAV or RWY TRK at 30 ftNo V2: no SRS; V/S engages 5 s after lift-off Takeoff: SRS + RWY MAN FLX +58 SRS CLB RWY NAV 1 FD 2 A/THR Engage levers to TOGA or FLX: V2 inserted, slats out, on ground 30 s SRS target V2 + 10 kt all engines; engine failure: higher of V2 or current, max V2 + 15 SRS limits pitch 18° (22.5° in windshear) · at least 120 ft/min SRS ends at ACC ALT, ALT* above 400 ft, another mode, or SPD pulled → OP CLB RWY yaw bar on the LOC signal: LOC within ½ dot, heading within 20° RWY TRK / NAV at 30 ft RA: NAV if armed, otherwise RWY TRK
Chapter 7 · AP/FD Lateral and Vertical Modes
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The takeoff mode joins SRS in pitch and runway mode in roll. Both engage when you set the thrust levers to TOGA or FLX, as long as V two is inserted on the PERF TAKEOFF page, the slats are out, and the aircraft has been on the ground for thirty seconds. SRS pitches to hold V two plus ten with both engines. With an engine failure the target is the higher of V two or the current speed, never more than V two plus fifteen. It also limits the attitude to eighteen degrees, or twenty two and a half in windshear, and keeps at least one hundred and twenty feet per minute. SRS ends at the acceleration altitude. Runway mode uses the localizer for the yaw bar on the ground, if there is one; at thirty feet NAV engages if armed, otherwise runway track. Forget V two, and there is no SRS at all.
Common modes: ILS
Arming and capturing the ILS APPR pb with an ILS selected, above 400 ft RA , ILS and RA valid, same ILS on both receivers FMA: LOC and G/S blue; capability shown; second AP allowed G/S* cannot engage before LOC* , nor from above unless the path crosses the beamLOC convergence: 20° intercept within 20 NM (NAV + LOC armed) APPR pb again above 400 ft: HDG V/S ; LOC pb: G/S disarms LOC or G/S lost 7 s above 200 ft : AP/FD off, FD basic modes Capturing the ILS localizer HDG, LOC armed LOC* LOC glide slope ALT, G/S armed G/S* G/S • APPR pb above 400 ft RA, ILS and RA valid, same ILS on both receivers • G/S* only after LOC*; not from above unless the path crosses the beam • LOC or G/S lost 7 s above 200 ft: AP/FD off, FDs in basic modes
Chapter 7 · AP/FD Lateral and Vertical Modes
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
For an ILS you press the APPR button. It arms the localizer and glideslope if an ILS approach is selected, you are above four hundred feet radio height, the ILS and radio altimeters are valid, and the same frequency and course are set on both receivers. The FMA shows LOC and G S in blue, the landing capability appears, and now you may engage the second autopilot. Watch the scene: the localizer is the lateral beam and the glideslope the vertical one. First LOC star captures, then LOC tracks. G S star cannot engage before LOC star, and it captures normally from below. Coming from above, it engages only if your path actually crosses the beam. Then G S tracks the beam down to LAND at four hundred feet, and FLARE and ROLL OUT at the runway.
Common modes: autoland
LAND, FLARE and ROLL OUT G/S · LOC A/THR in SPEED 700 ft VAPP memorised LAND LOC and G/S locked 200 ft AUTO LAND light armed FLARE ≈ 40 ft · A/THR RETARD ROLL OUT centreline on the LOC SPEED LAND CAT 3 DUAL RADIO 50AP1+2 1 FD 2 A/THR Below 400 ft no FCU action disengages LAND: only a go-around, or both AP/FD off After main gear touchdown the AP lowers the nose ROLL OUT: yaw bar on the PFD, no FD bars
Chapter 7 · AP/FD Lateral and Vertical Modes
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow an automatic landing down the glide path. On the localizer and glideslope the autothrust holds the approach speed, and at seven hundred feet it memorises that target so that a flight management failure cannot upset it. At four hundred feet radio height, with both LOC and G S engaged, LAND engages. From now on the guidance is locked: no FCU action will take it out of LAND. Only a go-around, or switching both autopilots and flight directors off, ends it. Below two hundred feet the autoland warning light is armed. At around forty feet, depending on the vertical speed, FLARE engages, the yaw axis is aligned with the runway and the autothrust retards to idle. At touchdown ROLL OUT engages and steers along the centreline using the localizer, with only the yaw bar on the PFD, and the autopilot lowers the nose.
Autoland warning and capability
AUTO LAND light and CAT 1, 2, 3 AUTO LAND flashes red below 200 ft RA with AP in LAND or FLARE if:LOC deviation > ¼ dot (above 15 ft) or GLIDE > 1 dot (above 100 ft) LOC lost above 15 ft, GLIDE lost above 100 ft, RAs differ > 15 ft Last AP off, long flare or untimely flare FMA column 4: CAT 1, CAT 2, CAT 3 SINGLE, CAT 3 DUAL No LAND at about 400 ft: CAT 1 and triple click: no autoland AUTO LAND flashes red below 200 ft RA (AP on, LAND or FLARE) if: • LOC deviation > ¼ dot above 15 ft (LOC scale flashes) • GLIDE deviation > 1 dot above 100 ft (G/S scale flashes) • LOC signal lost above 15 ft · GLIDE lost above 100 ft • the two RAs differ by more than 15 ft • the last AP disengages • long flare, or untimely flare with one RA lost FMA column 4: each FMGC works out its own capability CAT 1 CAT 2 CAT 3 SINGLE CAT 3 DUAL SINGLE = fail passive · DUAL = fail operational No LAND at about 400 ft: capability drops to CAT 1, triple click; no autoland with CAT 1 on the FMA
Chapter 7 · AP/FD Lateral and Vertical Modes
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Below two hundred feet, with an autopilot engaged in LAND or FLARE, the red AUTO LAND light flashes if anything happens that should stop an automatic landing. That means a localizer deviation over a quarter of a dot above fifteen feet, a glide deviation over one dot above one hundred feet, the loss of either signal, a difference of more than fifteen feet between the two radio altimeters, the last autopilot disengaging, or a long flare. Each FMGC also works out its own landing capability, shown in FMA column four as soon as the approach is armed: CAT one, CAT two, CAT three single, which is fail passive, and CAT three dual, which is fail operational. If LAND has not appeared by about four hundred feet, the capability drops to CAT one with a triple click, and an autoland is not allowed.
Common modes: non precision
APP NAV, FINAL and FINAL APP APPR pb above 400 ft AGL , valid F-PLN with a non-ILS approach : FINAL and APP NAV blue APP NAV engages like NAV; needs the white TO waypoint FINAL APP : approach phase active, within ±1.5 NM and +150 ft of the FDP, descending legBlue arrow on the ND: descent starts there; white arrow: it will not At the MAP : V/S and HDG or NAV · VDEV scale ±200 ft V/S pulled: only FINAL drops, NAV stays Managed non precision approach blue arrow: descent starts here FDP MAP FINAL APP APP NAV FINAL armed SPEED FINAL APP BARO 540AP1 1 FD 2 A/THR • APPR pb above 400 ft AGL, valid F-PLN with a non-ILS approach: FINAL and APP NAV blue • FINAL APP: approach phase active, within ±1.5 NM and +150 ft of the FDP • At the MAP: V/S (FPA) and HDG/TRK or NAV · DISCONNECT AP FOR LDG at minimum • Pull V/S: only FINAL disengages, NAV stays · LOC-only: use the LOC pb
Chapter 7 · AP/FD Lateral and Vertical Modes
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
For a VOR, NDB or RNAV approach in the flight plan, the APPR button arms FINAL and APP NAV, shown in blue, if you are above four hundred feet and the flight plan is valid. APP NAV engages like NAV, at once if NAV was already engaged. FINAL APP, the managed vertical and lateral mode, engages when the approach phase is active, you are within one and a half nautical miles laterally and one hundred and fifty feet above the final descent point, and you meet a descending leg. A blue arrow on the ND shows where the descent will begin; if it is white, something is missing and the aircraft will not descend. FINAL shows vertical deviation on a two hundred foot scale. At the missed approach point the modes revert, and if you pull vertical speed, only FINAL drops out and NAV stays.
Common modes: go-around
The go-around mode One lever to TOGA , flap lever ≥ 1 , in flight (or < 30 s on ground)SRS : higher of current speed or VAPP , max VLS + 25 (VLS + 15 engine out)Lateral: GA TRK , or NAV on later standards; FD bars return SRS ends at GA ACC ALT , ALT* above 400 ft, or speed pulled → OP CLB Then speed target: lower of green dot or a constraint Dual AP: leaving GA on either axis disconnects AP 2 Go-around: one lever to TOGA MAN TOGA SRS CLB GA TRK NAV CAT 3 DUAL AP1 1 FD 2 A/THR older standard: GA TRK · later standard: SRS with NAV engaged Engages at least one lever at TOGA, flap lever ≥ 1, in flight or < 30 s on ground SRS speed higher of current or VAPP, max VLS + 25 (VLS + 15 engine out) Lateral GA TRK on the current track, or NAV; HDG kept if already in HDG below 100 ft SRS ends GA ACC ALT, ALT* above 400 ft, another mode, or speed pulled → OP CLB After SRS target = the lower of green dot or a speed constraint Two APs leaving GA on either axis disconnects AP 2
Chapter 7 · AP/FD Lateral and Vertical Modes
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
The go-around mode engages the moment you push at least one thrust lever to TOGA with the flap lever at one or more, either in flight or within thirty seconds of touching down; in that last case the autopilot drops and can be re engaged five seconds after lift off. The flight director bars come back automatically, replacing the flight path vector. SRS holds the speed you had, or VAPP if that is higher, limited to VLS plus twenty five with both engines and VLS plus fifteen with one. Laterally you get GA TRK on the current track, or on later standards NAV. SRS ends at the go-around acceleration altitude, at altitude capture above four hundred feet, or if you select another mode or a speed. Then the target becomes green dot, or a lower speed constraint. And with two autopilots, leaving go-around on either axis drops autopilot two.
Mode reversions
Automatic mode changes you must expect Engaged Event Becomes Alert CLB, OP CLB, EXP CLB FCU altitude set below the aircraft V/S (FPA) on current, or preselected V/S box; triple click if not confirmed DES, OP DES, EXP DES FCU altitude set above the aircraft V/S (FPA) on current, or preselected V/S box; triple click if not confirmed ALT* FCU altitude changed by more than 250 ft V/S (FPA) on current triple click, FD pitch bar flashes CLB NAV lost (HDG pulled, discontinuity) OP CLB; constraints ignored lateral and vertical boxed, triple click DES NAV lost V/S on current; pitch unchanged triple click if not confirmed in 5 s SRS speed selected OP CLB triple click NAV, APP NAV, FINAL APP F-PLN lost or discontinuity HDG/TRK (basic) triple click
Chapter 7 · AP/FD Lateral and Vertical Modes
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mode reversions are automatic changes that keep the autopilot, flight director and autothrust consistent with what you have just done. Because nobody asked for them, you must watch the FMA. There are only two big families. First, a change of FCU altitude that no longer fits the active mode: set an altitude below you in a climb, or above you in a descent, or move it by more than two hundred and fifty feet during altitude capture, and vertical speed engages on the current rate, so the aircraft keeps going the way it was. Second, the loss of NAV: CLB becomes open climb, ignoring constraints, and DES becomes vertical speed. In each case the mode is boxed, and if you do not confirm with an altitude change, a level off or a vertical speed within five seconds, the triple click sounds.
Speed protection
When the speed comes first FD only, open climb: VMAX + 4 → FDs off, A/THR SPEED, thrust down FD only, open descent: VLS − 2 (to VLS − 19 with speedbrakes) → FDs off, thrust up V/S or FPA too high: reduced at VLS (climb) or VMAX (descent) V/S stays engaged; amber flashing box , triple click (AP on) Triple click = an unexpected mode change: read the FMAFD only, bars not followed (AP off) Open climb • CLB, OP CLB, EXP CLB • pitch too low, CLB thrust • speed climbs to VMAX + 4 • FDs disengage, triple click • A/THR → SPEED, thrust reduced Open descent • DES, OP DES, EXP DES • pitch too high, IDLE thrust • speed falls to VLS − 2 • (VLS − 2 to − 19 with speedbrakes) • FDs off, A/THR → SPEED, thrust up Excessive V/S or FPA (AP on) SPEED V/S-3000 ALT HDG AP1 1 FD 2 A/THR descending: V/S reduced at VMAX · climbing: at VLS (VLS − 5 if target is VLS) V/S stays engaged; amber flashing box, value pulses, triple click FD only: pitch bar adjusted, no triple click, FMA unchanged
Chapter 7 · AP/FD Lateral and Vertical Modes
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 guidance never lets you fly into an overspeed or underspeed just because a mode says so. Flying by hand with only the flight director, in an open climb, if you do not follow the bars and let the nose drop with climb thrust set, the speed rises; at VMAX plus four both flight directors disengage, the autothrust goes to speed mode and reduces thrust, and a triple click sounds. In an open descent at idle with the nose too high, the same happens at VLS minus two, and the autothrust adds thrust. With the autopilot flying an excessive vertical speed, it keeps V S engaged but reduces the rate at VLS when climbing or at VMAX when descending, with the flashing amber box and a triple click. That triple click is your cue: something changed that you did not ask for.
Summary
Guidance modes in one page SPEED G/S* ALT LOC CAT 3 DUAL RADIO 100AP1+2 1 FD 2 A/THR The rule Pitch flies speed → A/THR thrust (THR CLB, THR IDLE). Pitch flies path → A/THR SPEED. Push managed, pull selected.
Lateral HDG basic. NAV needs F-PLN, captures before the TO waypoint. LOC pb: localizer only. Preset before 30 ft disarms NAV.
Vertical CLB/DES need NAV and respect constraints; OP modes ignore them. ALT* + 250 ft change → V/S. ALT within 20 ft.
Common SRS V2+10. LAND at 400 ft, FLARE ≈ 40 ft. FINAL APP ±1.5 NM, +150 ft. GA: one lever TOGA, flaps ≥ 1.
Chapter 7 · AP/FD Lateral and Vertical Modes
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
To wrap up. The pitch mode decides the autothrust: if pitch flies the speed, the engines give a fixed thrust; if pitch flies a path, the engines hold the speed. Push for managed, pull for selected. Laterally, heading is the basic mode; NAV follows the flight plan and only captures before the TO waypoint; the LOC button gives the localizer alone. Vertically, managed climb and descent need NAV and respect constraints, while the open modes ignore them; change the altitude by more than two hundred and fifty feet in capture, and you get vertical speed. For the common modes, SRS holds V two plus ten, LAND engages at four hundred feet and flare at about forty, FINAL APP needs to be close to the final descent point, and one lever at TOGA with flaps out gives you the go-around.