A320 Aircraft Systems · Chapter 19
Ice and Rain Protection How hot bleed air and electrical heat keep the slats, engine intakes, windows and probes clear of ice, and how wipers and rain repellent keep the windshield clear in heavy rain.
ANTI ICE WING FAULT ON ENG 1 FAULT ON ENG 2 FAULT ON PROBE/WINDOW HEAT ON A U T O hot air · electrical heat · wipers © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to ice and rain protection, chapter thirty. The A320 is cleared to fly without restriction in icing conditions and heavy rain, and this lesson shows you how. Two kinds of energy do the work. Hot air from the engines protects the outer slats and the engine intakes, and electrical heat protects the windows, the probes and the drain mast. Then wipers and, on some aircraft, rain repellent keep the windshield clear. We will learn the valve logic that examiners like to test, especially what happens when electrical power is lost, and exactly what the crew sees on the panel and the ECAM.
Lesson roadmap
Ice and rain protection in four parts ATA chapter 30 . The aim: unrestricted operation in icing conditions and heavy rain.
1 · Wing anti-ice Hot bleed air to slats 3, 4, 5 , one valve per wing, the 30 s ground test , thrust effects and the WING pb.
2 · Engine anti-ice Independent HP compressor air to each intake lip, earlier and later valves, fail-safe open .
3 · Windows and probes Electrical heat: 2 WHCs , 3 PHCs , low and normal power, the PROBE/WINDOW HEAT pb.
4 · Rain and detection Wipers , rain repellent (some aircraft) and the visual ice indicator .
Chapter 19 · Ice and Rain Protection
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our plan for chapter thirty. Part one is wing anti-ice: hot air from the pneumatic system to three slats on each wing, controlled by one pushbutton, with a short test on the ground and some logic you must know. Part two is engine anti-ice: every engine heats its own intake with air from its own high pressure compressor, and we will compare the earlier and later valve designs. Part three is electrical heating of the windows and the probes, with their computers and the PROBE/WINDOW HEAT pushbutton. Part four is rain removal and ice detection: wipers, rain repellent where fitted, and the simple visual ice indicator between the windshields. Throughout, we will keep asking what the crew sees and what happens when something fails.
Overview
Hot air or electrical heat Windshields + side windows electrical: anti-ice / defog Probes pitot, static, AOA, TAT · electrical Engine anti-ice intake lips · own HP compressor air Wing anti-ice slats 3, 4, 5 · hot air from the pneumatic system Waste-water drain mast electrical hot air electrical Rain: wipers on both front windshields; rain repellent on some aircraft. Hot air : three outboard slats of each wing, engine air intakes. Electrical : cockpit windows, probes, waste-water drain mast.
Chapter 19 · Ice and Rain Protection
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 protects only the critical areas, and it uses two kinds of heat. Hot air from the pneumatic system protects the three outboard slats of each wing, slats three, four and five, and a separate hot-air system protects each engine’s air intakes. Hot air is used where a lot of energy is needed over a large, cold leading edge. Electrical heating protects the cockpit windows, the probes, which means the pitot probes, the static ports, the angle of attack and the total air temperature probes, and the waste-water drain mast, so that it cannot freeze up. Notice what is not on the list: the inboard slats and the tail surfaces are not heated. For rain, wipers and, on some aircraft, rain repellent clear the windshield.
Overview
Every system in one table Area Heat source Controlled by Crew control Slats 3, 4, 5 (each wing) hot air from the pneumatic system one valve per wing WING pb (both wings) Engine air intakes hot air from that engine’s HP compressor one valve, or two PRSOVs ENG 1, ENG 2 pbs Windshields (anti-ice), side windows (defog) electrical 2 WHCs, one per side automatic, or PROBE/WINDOW HEAT ON Pitot, static, AOA, TAT electrical 3 PHCs: CAPT, F/O, STBY automatic, or PROBE/WINDOW HEAT ON Waste-water drain mast electrical automatic none Front windshields (rain) wipers, rain repellent (some) rotary selectors, RAIN RPLNT pbs crew
Anti-ice is selected by the crew for wing and engines; window and probe heat are automatic once an engine runs or the aircraft flies.
Chapter 19 · Ice and Rain Protection
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table is your one-page memory aid. The outer slats get hot air from the pneumatic system, through one valve per wing, and one WING pushbutton controls both wings together. The engine intakes get hot air from their own high pressure compressor, through one valve on earlier aircraft and two pressure regulating and shut-off valves on later ones, with one pushbutton per engine. The windshields are electrically anti-iced and the side windows demisted, controlled by two window heat computers. The probes are heated electrically under three probe heat computers. Note the big difference in the last column: wing and engine anti-ice must be selected by the crew, while window and probe heat come on automatically as soon as an engine is running or the aircraft is in flight.
Part 1 · Wing anti-ice
Hot air to the outer slats In flight , hot air from the pneumatic system heats slats 3, 4 and 5 of each wingAir goes through one valve in each wing One WING pb on the ANTI ICE panel controls both valves On the ground : a 30 s test only A wing leak closes the valve on that side automatically One valve per wing slat 2 slat 3 slat 4 slat 5 WAI valve pneumatic system WING pb ON : valves open if pneumatic air is availableOn the ground : open for a 30 s test onlyLeak detected : that side’s valve closes automaticallyElectrical power lost : the valves CLOSEOne WING pb controls both wings together.
Chapter 19 · Ice and Rain Protection
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
In flight, hot air from the pneumatic system heats the three outboard slats of each wing, slats three, four and five. The air is supplied through one valve in each wing, and the WING pushbutton on the ANTI ICE panel controls both valves together, so you cannot select one wing alone. The pneumatic system that supplies this air has its own lesson, where we see its sources and its leak detection. Watch the model: as the valve opens and the hot air is supplied, the outer leading edge warms up. If the leak detection system finds a leak in the hot air ducts of one wing, the wing anti-ice valve on that side closes automatically, so a burst duct does not keep blowing hot air into the wing structure.
Part 1 · Valve logic
When do the wing valves open? WING pb ON : valves open if pneumatic air is available On the ground : open for a 30 s test only, then close Wing leak : that side’s valve closes Electrical power lost : the valves close WING pb off: the valves close Wing anti-ice valve: open when… WING pb ON pneumatic supply available electrical power available no leak on that side AND in flight on ground, first 30 s after ON OR VALVE OPEN Any condition missing → the valve closes (both wings: one pb).
Chapter 19 · Ice and Rain Protection
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us make the valve logic exact, because it is a favourite exam topic. With the WING pushbutton ON, the valves open, provided pneumatic air is available. On the ground, the valves open for thirty seconds only. That is a test sequence: you can check that the system works without overheating the slats, which get no cooling airflow when the aircraft is standing still. If a leak is detected, the valve on the affected side closes automatically. And if the electrical power supply to the valves fails, the valves close. Hold on to that last rule, because we will see in a moment that the engine anti-ice valves do exactly the opposite. Finally, selecting the WING pushbutton off closes both valves.
Part 1 · Ground test
The 30-second test on the ground In flight: WING pb ON at t = 0 open shut 0 10 20 30 40 50 60 On the ground: WING pb ON at t = 0 open shut 0 10 20 30 40 50 60 30 s: valves close, test over s s What you see WING pb: blue ON stays lit FAULT: amber only briefly, while the valves move Memo: WING A.ICE (green) BLEED page: ANTI ICE legends; arrow green when a valve is open, amber if open on the ground for more than 10 s On the ground the WING pb starts a 30 s test : the valves open, then close by themselves. In flight they stay open.
Chapter 19 · Ice and Rain Protection
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the same selection made in flight and on the ground. In flight, select the WING pushbutton ON at time zero and the valves open and stay open. On the ground, the same selection opens the valves for thirty seconds and then they close automatically: the test is over, even though the pushbutton still shows the blue ON light. What do you see? The blue ON light in the pushbutton, the amber FAULT light only briefly while the valves are moving, the green memo WING A dot ICE on the ECAM, and on the BLEED page the ANTI ICE legends with arrows. An arrow is green when its valve is open; it turns amber if a valve is open with abnormal pressure, or stays open on the ground for more than ten seconds.
Part 1 · Engine effects
Anti-ice costs thrust Wing anti-ice selected: N1 or EPR limit automatically reduced … and idle N1 or EPR automatically increased Engine anti-ice: limit reduced, idle increased on both engines , if necessary Why: the bleed air taken must be paid for by the engines Higher idle keeps enough pressure for the anti-ice Bleed taken for anti-ice idle limit N1 or EPR Anti-ice ON → automatically: • N1 / EPR limit reduced (less margin to take off thrust) • idle N1 / EPR increased (enough bleed pressure) Engine anti-ice: idle raised on both engines, if necessary
Chapter 19 · Ice and Rain Protection
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Anti-ice air is not free. It is taken from the engines’ compressors, so the engines have less margin left for thrust. That is why, when wing anti-ice is selected, the engine control automatically reduces the N one or E P R limit, and at the same time increases the idle N one or E P R. The higher idle is there so that, even with the thrust levers at idle in a descent, the engines still deliver enough air pressure to keep the slats hot. Engine anti-ice does the same: when an engine anti-ice valve is open, the limit is reduced and, if necessary, the idle is raised for both engines, to provide the required pressure. In performance terms, this is why take-off and landing figures change with anti-ice on.
Part 1 · Controls
The WING pushbutton Off : ON light out; valves close ON (blue): memo WING A.ICE ; valves open if pneumatic air is available (30 s on ground)FAULT (amber) + ECAM caution: valve not in the selected position , or low pressure FAULT also comes on briefly while the valves transit One pb, both wings WING FAULT ON Off (dark) valves close WING FAULT ON ON (blue) valves open if pneumatic air is available WING FAULT ON FAULT (amber) valve not in the selected position or low pressure · + ECAM caution FAULT also flashes briefly while the valves are moving.
Chapter 19 · Ice and Rain Protection
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The WING pushbutton has three faces. Off, it is dark and both valves close. ON, it shows a blue ON light, the green memo WING A dot ICE appears on the ECAM, and the valves open if pneumatic air is available, for thirty seconds only on the ground. FAULT, in amber with an ECAM caution, means that a valve is not in the position you selected, or that low pressure has been detected, for example because the pneumatic supply is weak. Do not be alarmed by a short flash of FAULT when you switch the system on or off: the amber light comes on briefly while the valves are travelling, and goes out once they arrive. Only a steady FAULT is a real problem.
Part 1 and 2 · Indications
Anti-ice on the ECAM BLEED 24 °C C H 50 °C LO HI 25 °C C H 230 °C LO HI RAM AIR ANTI ICE ANTI ICE 44 180 PSI °C 1 IP HP 44 180 PSI °C 2 IP HP TAT +12 °C SAT -6 °C 10 H 42 GW 64300 KG 1 2 WING A.ICE ENG A.ICE 3 TOGA 88.4 % WAI NAI upper E/WD (later aircraft) example figures only 4 1 ANTI ICE legend when the WING pb is ON2 Arrow green: valve open · amber: open with low or high pressure, or open on the ground > 10 s3 Memos (green) WING A.ICE: WING pb ON · ENG A.ICE: one or both ENG pbs ON4 WAI / NAI thrust levers in TOGA or FLX/MCT (later aircraft)Engine anti-ice, later aircraft: ECAM cautions · ANTI ICE ENG 1(2) VALVE CLSD · ANTI ICE ENG 1(2) VALVE OPEN · ANTI ICE ENG 1(2) CTL FAULT · ANTI ICE ENG 1(2) OVER PRESS each with the amber FAULT light BLEED page ANTI ICE legends and arrows · green memos WING A.ICE and ENG A.ICE · WAI / NAI on the E/WD of later aircraft.
Chapter 19 · Ice and Rain Protection
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is where anti-ice shows up on the ECAM. On the BLEED page, the words ANTI ICE appear beside each side of the crossbleed duct when the WING pushbutton is ON, and an arrow shows the state of each wing valve: no arrow when the valve is closed, green when it is open, amber when it is open with low or high pressure, or open on the ground for more than ten seconds. On the memo page you get WING A dot ICE in green when the WING pushbutton is ON, and ENG A dot ICE in green when one or both engine pushbuttons are ON. On later aircraft, the engine warning display also shows W A I and N A I next to the thrust limit when the thrust levers are in the TOGA or FLEX M C T detent. Those later aircraft also have specific engine anti-ice cautions, listed on the right.
Part 2 · Engine anti-ice
Each engine heats its own intake Independent hot air from the HP compressor of the same engineProtects the nacelle air intake (the lip) Controlled by two pbs , one per engine: ENG 1 , ENG 2 The valve closes automatically if no air is available (engine not running) Earlier aircraft: one two-position valve; later: two PRSOVs Engine anti-ice HP compressor (engine core) anti-ice valve(s) intake lip (anti-iced area) Each engine: its own, independent hot air source. Earlier aircraft: one valve · later aircraft: two PRSOVs in series
Chapter 19 · Ice and Rain Protection
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Engine anti-ice is completely separate from the pneumatic system. Each engine has its own anti-ice supply: hot air taken from its own high pressure compressor and piped forward to the intake lip, the anti-iced area at the front of the nacelle. The crew controls it with two pushbuttons, one per engine, labelled ENG 1 and ENG 2. Watch the model: when the compressor is turning and the pushbutton is ON, the valve opens and the intake lip warms up. If the engine is not running, there is no air, and the valve closes automatically. On earlier aircraft there is one valve with two positions, open and closed. On later aircraft there are two pressure regulating and shut-off valves, which we look at next.
Part 2 · Two designs
Earlier and later engine anti-ice valves Earlier aircraft Later aircraft Valves per engine one, two positions (open / closed) two PRSOVs : electrically controlled, pneumatically actuated Anti-ice ON valve open both PRSOVs regulate in cascade Anti-ice OFF valve closed only one PRSOV does the shut-off No air (engine stopped) valve closes automatically valves closed (no air to actuate them) Leak or burst — continuous monitoring; burst duct: both valves closed Electrical power lost valve OPENS both PRSOVs fail-safe OPEN Indications FAULT if position disagrees FAULT + VALVE CLSD / VALVE OPEN / CTL FAULT / OVER PRESS; NAI on E/WD
Both designs agree on the key point: with no electrical power , the engine intake stays protected .
Chapter 19 · Ice and Rain Protection
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us compare the two designs. On earlier aircraft each engine has one valve with two positions. On later aircraft each engine has two pressure regulating and shut-off valves, P R S O Vs, electrically controlled and pneumatically actuated. With anti-ice on, the two regulate in cascade, one after the other. With anti-ice off, only one of them does the shut-off job. Later aircraft also monitor the ducts continuously for a leak or burst, and if a burst duct is detected, both valves are commanded closed. But the most important line is electrical failure. On both designs, losing electrical power opens the engine anti-ice valves; on later aircraft, both P R S O Vs fail safe open, giving the intake enough pressure for anti-icing. The engine stays protected.
Exam favourite
Power lost: wing CLOSED, engine OPEN WING anti-ice valves electrical power lost CLOSE also close: leak on that side ENGINE anti-ice valves electrical power lost OPEN later aircraft: both PRSOVs fail-safe open Electrical failure: wing anti-ice valves close , engine anti-ice valves open . Learn them as a pair.
Chapter 19 · Ice and Rain Protection
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the single most examined fact in this chapter, so here it is on its own slide. If the electrical power supply fails, the wing anti-ice valves close. If electrical power fails, the engine anti-ice valves open. Why the difference? Ice on the engine intake can break off and damage the engine, and the engine anti-ice air is cheap and independent, so the safe default is to keep the intake protected. The later design states it directly: the valves fail safe open, providing enough pressure for the anti-ice function. For the wing, the design makes the opposite choice: with no electrical power, no hot air goes to the slats. A simple memory aid: the engine protects itself.
Part 2 · Controls
The ENG ANTI ICE pushbuttons Off : the valve closesON (blue): memo ENG A.ICE ; the valve opens if bleed air is available from that engine FAULT (amber) + ECAM caution: valve position disagrees with the pbFAULT comes on briefly while the valve transits Later aircraft: NAI on the E/WD in TOGA or FLX/MCT ANTI ICE WING FAULT ON ENG 1 FAULT ON ENG 2 FAULT ON PROBE/WINDOW HEAT ON A U T O ENG 1: ON (blue) valve opens if bleed air is available from that engine ENG 2: FAULT (amber) valve position disagrees with the pb · ECAM caution Off valve closes Memo ENG A.ICE green, if one or both ENG pbs are ON
Chapter 19 · Ice and Rain Protection
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ENG 1 and ENG 2 pushbuttons on the ANTI ICE panel work just like the WING pushbutton, one per engine. Off, the valve closes. ON, the blue light comes on, the green memo ENG A dot ICE appears, and the valve opens if bleed air is available from that engine. FAULT in amber, with an ECAM caution, means the valve position disagrees with what you selected. As with the wing, a brief FAULT while the valve travels is normal. On later aircraft, the caution tells you more: valve closed, valve open, control fault, or over pressure. And N A I appears on the engine warning display when the thrust levers are in the TOGA or FLEX M C T detent, reminding you that the thrust limit is reduced.
Worked cases
What happens if…? Situation Result WING pb ON at the gate, engines running valves open for 30 s , then close; ON stays blue; memo WING A.ICE WING pb ON in flight valves open; N1/EPR limit reduced , idle increased Leak detected in the LEFT wing ducts left wing anti-ice valve closes automaticallyENG 2 ANTI ICE ON, engine 2 not running valve closed : no air from that engine ENG 1 ANTI ICE ON in flight limit reduced; idle raised on both engines if necessary Electrical supply to the anti-ice valves lost wing valves close ; engine valves open Later aircraft: burst duct in ENG 1 anti-ice both ENG 1 PRSOVs commanded closed
Chapter 19 · Ice and Rain Protection
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us test ourselves with seven situations. WING pushbutton ON at the gate with engines running: the valves open for thirty seconds and close again, while the pushbutton stays blue and the memo shows. WING ON in flight: the valves stay open, the thrust limit is reduced and idle increased. A leak in the left wing ducts closes the left wing anti-ice valve. Engine two anti-ice selected ON with engine two not running: its valve stays closed, because there is no air from that engine. Engine one anti-ice ON in flight: idle may be raised on both engines, not just engine one. Loss of electrical power to the valves: wing valves close, engine valves open. And on later aircraft, a burst duct in the engine one anti-ice system closes both of its P R S O Vs.
Part 3 · Window heat
Electrically heated windows Windshields : electrical anti-icing ; side windows : defogging Two independent Window Heat Computers (WHC ), one per side They regulate, protect against overheat and indicate faults Windshield: low power on the ground , normal power in flight (automatic) Side windows: one heating level only Window heat windshield windshield side windows WHC 1 left side WHC 2 right side Each WHC: regulates, protects against overheat, indicates faults. Windshield: anti-ice; side windows: defog.
Chapter 19 · Ice and Rain Protection
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The cockpit windows are heated electrically, for two different jobs. The two front windshields are anti-iced, so you can always see out, and the side windows are defogged, so they do not mist up. Two independent window heat computers, one on each side, regulate the heating automatically, protect the windows against overheating and indicate faults. The windshields have two power levels: low power on the ground and normal power in flight, and the changeover is automatic. The side windows have only one heating level. Why low power on the ground? Without the cooling of the airflow, full power could overheat the glass, and there is no ice risk to compare with flight. Independence matters too: a failure on one side leaves the other pilot with a clear windshield.
Part 3 · Probe heat
Heated probes Electrically heated: pitot probes, static ports, AOA probes, TAT probes Three independent Probe Heat Computers (PHC ) One each for the CAPT , F/O and STBY probes Automatic control, overheat protection, fault indication On the ground: TAT not heated , pitot at low power Probe heat pitot static AOA TAT PHC CAPT captain probes PHC F/O first officer probes PHC STBY standby probes Three independent Probe Heat Computers: automatic control, overheat protection, fault indication.
Chapter 19 · Ice and Rain Protection
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The air data probes are heated electrically: the pitot probes, the static ports, the angle of attack probes and the total air temperature probes. An iced pitot or static port gives wrong airspeed and altitude, so this is critical. Three independent probe heat computers control them: one for the captain probes, one for the first officer probes and one for the standby probes. That split mirrors the three air data sources, so one computer failure affects only one set of probes. Each computer controls the heating automatically, protects against overheating and indicates faults. On the ground, two things are different: the T A T probes are not heated, and the pitot heating works at a low level. The change to normal power in flight is automatic.
Part 3 · PROBE/WINDOW HEAT
What is heated, and when? Ground, engines off (AUTO) Ground, ≥ 1 engine running (AUTO) Ground, engines off pb ON In flight (AUTO or ON) Windshields not heated low power low power normal power Side windows not heated heated heated heated Pitot probes not heated low power low power normal power Static ports not heated heated heated heated AOA probes not heated heated heated heated TAT probes not heated not heated not heated heated On the ground TAT probes are never heated; windshields and pitots run at low power. The change to normal power in flight is automatic. AUTO (pb dark): heated in flight , or on the ground with at least one engine running . ON (blue): heated permanently , e.g. before engine start.
Chapter 19 · Ice and Rain Protection
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The PROBE/WINDOW HEAT pushbutton has two states. In AUTO, with the pushbutton dark, probes and windows are heated automatically in flight, or on the ground provided at least one engine is running. Selected ON, with a blue light, they are heated permanently, which is how you get heating before engine start. Now read the table column by column. On the ground with the engines off in AUTO, nothing is heated. On the ground with an engine running, or with the pushbutton ON, the windshields and pitots run at low power, the side windows, static ports and angle of attack probes are heated, and the T A T probes are not. In flight, everything is heated, with the windshields and pitots at normal power, and that changeover is automatic.
Part 4 · Rain removal
Wipers Each front windshield has an electrical wiper Its own rotary selector : OFF , SLOW , FAST Intermittent sweep (INTMT ) on some aircraftOFF : the wiper stops out of view Rain repellent pb next to it, on aircraft that have it RAIN RPLNT WIPER OFF INTMT SLOW FAST RAIN RPLNT WIPER OFF INTMT SLOW FAST CAPT side (SLOW) F/O side (OFF) WIPER selector one per front windshield: OFF, SLOW, FAST INTMT intermittent sweep, on some aircraft OFF the wiper parks out of view RAIN RPLNT pb one per side (some aircraft): one measured spray per push
Chapter 19 · Ice and Rain Protection
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
For rain, each front windshield has its own electrical wiper with two speeds, and on some aircraft an intermittent sweep. Each wiper has its own rotary selector, so the captain and the first officer control their own side. The selector positions are OFF, SLOW and FAST, plus INTMT where intermittent is fitted. When you turn a wiper off, it stops out of your view, parked at the edge of the windshield rather than across your line of sight. Next to each wiper selector you may find a RAIN RPLNT pushbutton, for the rain repellent, which we look at next. Wipers and repellent only remove rain; ice on the windshields is handled by the electrical window heat.
Part 4 · Rain removal
Rain repellent (some aircraft) Used in moderate to heavy rain to improve visibility Separate RAIN RPLNT pbs for each side of the windshield One push: a timer applies a measured quantity ; push again to repeat About 30 s later the windshield is covered with spray Inhibited on the ground with the engines stopped Bottle gauge: yellow sector or REFILL float → replace the bottle Rain repellent (some aircraft) bottle timed valve CAPT windshield timed valve F/O windshield One push = one measured dose (push again to repeat). About 30 s later the windshield is covered with spray. Inhibited on the ground with the engines stopped. pressure gauge yellow = replace nitrogen pressure shows the fluid left; a REFILL float on some aircraft
Chapter 19 · Ice and Rain Protection
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some aircraft have a rain repellent system. In moderate to heavy rain, the crew can spray a repellent liquid on the windshield, so that the rain beads up and is blown away, improving visibility. There is a separate RAIN RPLNT pushbutton for each side. Each push starts a timer that applies one measured quantity of repellent; to apply more, you push again. After about thirty seconds the windshield is covered with the spray. The function is inhibited on the ground when the engines are stopped. The bottle has a pressure gauge, reading the nitrogen pressure and therefore the fluid left: when the needle is in the yellow sector, or the REFILL float is visible on aircraft that have one, the bottle should be replaced.
Part 4 · Ice detection
The visual ice indicator An external visual ice indicator between the two windshields Both pilots can see ice building on it Some aircraft: an external ice detector light Your cue for anti-ice decisions , together with the conditions Visual ice indicator indicator between the two windshields ice builds on it first: easy for both pilots to see external ice detector light on some aircraft (to see it at night)
Chapter 19 · Ice and Rain Protection
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do you know that you are picking up ice? The A320 has an external visual ice indicator, a small probe mounted between the two windshields, where both pilots can see it. Ice tends to build on it, so it gives you a simple visual cue that the airframe is icing. Some aircraft also have an external ice detector light, which lets you see the indicator at night. The indicator is one input to your anti-ice decisions; your operating procedures also define icing conditions in terms of temperature and visible moisture, and those come from your company procedures rather than this system description. Remember that the windshield itself is heated, so it will not show you ice; the indicator will.
Exam traps
Six things candidates get wrong Slats 3, 4, 5 only Wing anti-ice heats the three outboard slats , not the whole leading edge, and not the tail.
30 s on the ground WING ON on the ground is a 30 s test . In flight the valves stay open.
Power lost Wing valves close . Engine valves open (later: both PRSOVs fail-safe open).
Independent engine air Engine anti-ice uses its own HP compressor air, not the pneumatic system.
Both engines’ idle Engine anti-ice on one side can raise idle on both engines , if necessary.
TAT on the ground TAT probes are not heated on the ground ; pitots and windshields at low power .
Chapter 19 · Ice and Rain Protection
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six traps before the summary. One: wing anti-ice heats only the three outboard slats, three, four and five. Two: selecting the WING pushbutton on the ground gives a thirty-second test, not continuous heating. Three, the classic: losing electrical power closes the wing valves but opens the engine valves. Four: engine anti-ice uses air from its own high pressure compressor; it does not depend on the pneumatic system, the crossbleed or the APU. Five: engine anti-ice on one engine can raise the idle on both engines, if necessary. Six: on the ground the T A T probes are not heated, and pitots and windshields run at low power. If you can explain each of these in your own words, you are ready for the questions.
Summary
Ice and rain protection on one page Wing Hot pneumatic air to slats 3-4-5 , one valve per wing, one WING pb. Ground: 30 s . Leak or power loss: close .
Engine Own HP compressor air to the lip; ENG 1 / ENG 2 pbs; no air → closed; power loss → open .
Thrust Anti-ice ON: N1/EPR limit reduced , idle increased (engine anti-ice: both engines, if necessary).
Windows 2 WHCs . Windshields anti-ice (low on ground, normal in flight); side windows defog, one level.
Probes 3 PHCs (CAPT, F/O, STBY). AUTO: in flight or ≥ 1 engine running; ON : permanent. No TAT heat on ground.
Rain and ice Two-speed wipers (+ INTMT), rain repellent where fitted, visual ice indicator between the windshields.
Chapter 19 · Ice and Rain Protection
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Wing anti-ice sends hot pneumatic air to slats three, four and five through one valve per wing, under one WING pushbutton; on the ground it runs a thirty-second test, and a leak or a power loss closes the valves. Engine anti-ice uses each engine’s own compressor air; no air means the valve is closed, and a power loss opens it. Either way, anti-ice reduces the thrust limit and raises idle. Two window heat computers look after the windshields and side windows, and three probe heat computers look after the probes, automatically once an engine runs or the aircraft flies, or permanently with the pushbutton ON. And for rain, wipers and repellent, with the visual ice indicator to tell you when ice is forming. Well done.