A320 Aircraft Systems · Chapter 22
Landing Gear and Nose Wheel Steering How the A320 raises and lowers its gear: the LGCIUs, green hydraulics and the safety valve, the gravity crank, the indications, and how the nose wheel is steered.
UP DOWN LDG GEAR UNLK UNLK UNLK WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the landing gear of the A320. Three short legs carry the whole aeroplane on the ground, and twice every flight they fold away and come back again. In this lesson we look at the two main gears and the nose gear, the doors that cover them, and the two control units, the L G C I Us, that sequence everything and tell the rest of the aircraft whether it is flying or on the ground. We will follow the green hydraulic supply through the safety valve, learn the gravity extension crank, read the indicator panel and the WHEEL page, and finish with nose wheel steering. Brakes have a lesson of their own, straight after this one.
Landing gear
Our route through ATA 32 UP DOWN LDG GEAR UNLK UNLK UNLK WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL G E A R G E A R GRAVITY GEAR EXTN PULL & TURN Nose wheel steering up to 75° Gear and doors Three legs, their doors and the retraction and extension sequence.
LGCIUs Two control units: sequencing, alternation and the flight or ground signal.
Controls and failures Lever, safety valve, indications and gravity extension.
Steering Handwheels, pedals and the BSCU driving a yellow hydraulic actuator.
Chapter 22 · Landing Gear and Nose Wheel Steering
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through chapter thirty two, the landing gear. First the hardware: the two main gears, the nose gear, their doors, and the sequence the doors and legs follow every time you move the lever. Then the brains of the system, the two landing gear control and interface units, which you will hear called L G C I U one and two. They do far more than move the gear, because almost every system on the aircraft asks them one question: are we flying or on the ground? Next come the cockpit controls and what can go wrong: the lever and its interlock, the safety valve that locks the gear out above two hundred and sixty knots, the indicator panel, the WHEEL page and the gravity extension crank. We finish with nose wheel steering.
Gears and doors
Three legs, twin wheels Two main gears retract inboard into the belly One nose gear retracts forward Every leg: twin wheels and an oleo-pneumatic shock absorber Each main wheel has an anti-skid brake ; the nose gear has steering Gear and doors: electrically controlled , hydraulically operated Nose gear retracts forward twin wheels, steering Main gears retract inboard twin wheels, braked Gear and doors: electrically controlled, green hydraulic power
Chapter 22 · Landing Gear and Nose Wheel Steering
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 sits on three legs, and each one carries a pair of wheels. The two main gears hang under the wing roots, and when they retract they swing inboard, so the wheels end up side by side in the belly. The nose gear retracts forward into its bay under the cockpit. Every leg has an oleo-pneumatic shock absorber, which we look at next. Each of the four main wheels carries an anti-skid brake, while the nose wheels have no brakes but can be steered. When the gear is up, the bays are closed by doors, so the belly stays smooth. Remember one line for the exam: the gear and doors are electrically controlled, by the two control units, and hydraulically operated, by the green system.
Gears and doors
What is on each leg Retraction actuator swings the leg up and downLock stay braces the leg when it is downDownlock actuator and downlock springs hold the stay lockedNose leg: also a steering actuator Ground safety pins stop the stay unlocking on the ground MAIN GEAR (front view) NOSE GEAR (side view) wing and belly structure lock stay downlock actuator downlock springs retraction actuator shock absorber twin wheels, each braked nose structure retraction actuator steering actuator drag stay twin wheels, no brakes FWD Every leg: oleo-pneumatic shock absorber. Safety pins can lock the stays on the ground.
Chapter 22 · Landing Gear and Nose Wheel Steering
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at the parts on each leg, because they explain how gravity extension works later. A hydraulic retraction actuator swings the leg into the bay and back out. When the leg is down, a folding lock stay braces it against the structure, and that stay is held straight, or locked, by a downlock actuator and a set of downlock springs. To retract, hydraulics first break the lock and then the actuator lifts the leg. The nose gear has the same idea, with a drag stay, its own retraction actuator, and in addition a steering actuator powered by the yellow system. On the ground, maintenance can fit safety pins that stop the stays from unlocking. Notice those springs: during a gravity extension they are what pulls the main gear stays into the locked position.
Gears and doors
The shock absorber gives the ground signal Nitrogen is the spring, oil through an orifice gives dampingStrut compressed = weight on wheels Proximity detectors sense compressed or extendedBoth LGCIUs turn this into a flight / ground signal N₂ oil Proximity detector compressed: ground extended: flight nitrogen: spring oil through orifice: damping LGCIU 1 and 2 turn this into a flight or ground signal for other systems
Chapter 22 · Landing Gear and Nose Wheel Steering
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each leg absorbs the landing in an oleo-pneumatic shock absorber. Nitrogen at the top acts as the spring, and oil forced through an orifice soaks up the energy, giving damping. Watch the touchdown: the strut compresses quickly, then settles to its static position. That movement matters far beyond comfort. Proximity detectors on the struts sense whether each shock absorber is compressed or extended, and they report to both control units. The units turn that into the single most important discrete signal on the aircraft: flight or ground. Pressurisation, the thrust reversers, the APU, the lights and many other systems ask the L G C I Us which one it is, as we will see in a few slides.
Gears and doors
Retraction: doors open, gear moves, doors close 1 Doors open all gear doors open 2 Gear moves each leg swings to its new position 3 Doors close doors close and lock Doors on the struts move with the legs; the bay doors open for every retraction or extension and close at the end.
Chapter 22 · Landing Gear and Nose Wheel Steering
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the sequence you will see after every take-off. When the lever goes up, all the gear doors open first. Then each leg swings to its new position, the main gears inboard and the nose gear forward. Finally the doors close again. Watch them retract now. Extension is the mirror image: doors open, gear down, doors close. Notice there are two kinds of doors. Some are fitted to the gear struts themselves, and the leg moves them mechanically, so they close as the leg arrives at the end of retraction. The others are the hydraulically operated bay doors, and all of these open whenever the gear is retracting or extending. So in normal operation, a closed bay is a finished sequence, whichever way the gear went.
Gear control
Lever, LGCIUs and green hydraulics GREEN HYDRAULIC SUPPLY SAFETY VALVE shut above 260 kt CUT-OFF VALVE shut by the gravity crank DOOR SELECTOR GEAR SELECTOR doors nose and main gears LGCIU 1 LGCIU 2 behind 2 L/G lever proximity detectors electrical ECAM WHEEL page LDG GEAR panel (LGCIU 1 only) Green hydraulics moves every gear and door LGCIUs: electrical sequencing Electrical sequencing by the LGCIUs; hydraulic power from green through the safety valve and the cut-off valve.
Chapter 22 · Landing Gear and Nose Wheel Steering
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the whole gear control system on one page. The lever is purely electrical: it sends its position to both control units, and so do the proximity detectors on the legs and doors. The controlling unit then energises two selector valves, one for the doors and one for the gears, in the right order. The power comes from the green hydraulic system only. Before it reaches the selector valves, green has to pass two valves in series. The first is the safety valve, which shuts off the supply at high speed. The second is the cut-off valve, which the gravity extension crank closes. Both units send gear information to the ECAM WHEEL page, but only L G C I U one drives the LDG GEAR indicator panel. Keep that detail for the indications slides.
Gear control
The 260 kt safety valve Above 260 kt the safety valve cuts off green supply to the gear Below 260 kt, supply stays cut off while the lever is UP Speed comes from ADR 1 and ADR 3 On the ground (main gear compressed) the valve can open Lever DOWN below 260 kt opens it again Safety valve opening logic ADR 1: below 260 kt ADR 3: below 260 kt main gear on ground OR L/G lever DOWN OR AND open valve self-maintained (latched) Worked example: one flight Taxi out, lever DOWN OPEN After take-off, lever UP, 180 kt OPEN: gear retracts Climb through 260 kt SHUT Back below 260 kt, lever still UP stays SHUT Approach, lever DOWN, 220 kt OPEN
Chapter 22 · Landing Gear and Nose Wheel Steering
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The safety valve protects the gear and doors from being moved at high speed. Read the logic on the left. The valve opens only when the speed condition is met, that is air data reference one or air data reference three reads below two hundred and sixty knots, or the main gear is on the ground, and at the same time the lever is down, or the valve is already latched open. Now walk through a flight. On the ground it is open. After take-off you select up below two hundred and sixty, the latch holds it open and the gear retracts. Climb through two hundred and sixty knots and the valve shuts. Come back below it with the lever still up, and it stays shut. Only when you select the lever down below two hundred and sixty does green reach the gear again.
LGCIUs
Two LGCIUs, taking turns LGCIU 1 and LGCIU 2 sequence the gear and doorsOne unit controls a complete gear cycle Hand-over to the other unit at the end of each retraction If one fails , the healthy one takes control Both feed ECAM; LGCIU 1 alone feeds the LDG GEAR panel Who controls the gear? Cycle 1 LGCIU 1 extension and retraction Cycle 2 LGCIU 2 extension and retraction Cycle 3 LGCIU 1 extension and retraction Hand-over at the end of each retraction If the controlling LGCIU fails the healthy one takes control: the gear still works normally Indications WHEEL page: LGCIU 1 and 2 · LDG GEAR panel: LGCIU 1 only
Chapter 22 · Landing Gear and Nose Wheel Steering
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The two control units share the work in a simple way. One of them controls a complete gear cycle. At the end of the retraction it hands over automatically to the other unit, which then runs the next cycle, and so on. That alternation means both units and their circuits are exercised regularly, and a dormant failure in one of them shows up quickly. If the unit in control fails, the gear is controlled by the remaining healthy one, so a single failure does not stop you lowering the gear normally. Both units send gear positions to the ECAM WHEEL page, which is why each leg shows two triangles. But the LDG GEAR indicator panel is wired to unit one only. If unit one loses its power, that panel goes dark while the WHEEL page still works.
Cockpit controls
The landing gear lever Two positions: UP and DOWN ; move it in one continuous movement UP: main wheels braked automatically while the doors open DOWN on the ground: interlock locks the lever Interlock: a main strut compressed or steering not centred Red arrow : gear not locked down in landing configurationUP DOWN UP main wheels braked automatically while the doors open; nose wheels stopped by a brake band (some a/c) DOWN lever locked DOWN on the ground: a main strut compressed, or nose wheel steering not centred Red arrow gear not locked down in landing configuration, plus a red ECAM warning Move the lever in one continuous movement, no pause Gear down: gear hydraulics stay pressurised (green available)
Chapter 22 · Landing Gear and Nose Wheel Steering
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The lever sits on the centre instrument panel, and it has just two positions. Always move it in one continuous movement, with no pause between them. Selecting up starts retraction, and while the doors are opening the normal brakes automatically stop the main wheels from spinning, so they do not enter the bay rotating. On aircraft with nose gear rubbing strips, a brake band in the nose bay stops the nose wheels as the doors close. Down selects extension. On the ground, an interlock locks the lever down if either main shock absorber is compressed, or if the nose wheel steering is not centred, so nobody can retract the gear by accident. With the gear down, the gear hydraulics stay pressurised. And the red arrow lights, with a red ECAM warning, if the gear is not locked down in landing configuration.
Indications
The LDG GEAR indicator panel Three lights, one per gear: UNLK above a triangle Green triangle : gear locked downRed UNLK : gear not locked in the selected positionFed by LGCIU 1 only : needs LGCIU 1 powered A stuck UNLK: confirm on the WHEEL page LDG GEAR UNLK UNLK UNLK Gear up and locked, or no power all lights out LDG GEAR UNLK UNLK UNLK Gear in transit red UNLK: not locked in the selected position LDG GEAR UNLK UNLK UNLK Gear down and locked green triangles LDG GEAR UNLK UNLK UNLK Right gear UNLK and triangle? check the WHEEL page: one green triangle is enough
Chapter 22 · Landing Gear and Nose Wheel Steering
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Next to the lever is the LDG GEAR indicator panel, with one light for each gear: left, nose and right. Each light has a red UNLK legend at the top and a green triangle underneath. A green triangle means that gear is locked down. A red UNLK means the gear is not locked in the position the lever has selected, which is normal for a few seconds while it travels. With the gear up and locked, the panel is dark. Because the panel is connected only to L G C I U one, it only works while that unit is powered. So what if one UNLK stays on after the gear is down? Look at the WHEEL page, which uses both units. If that gear shows even one green triangle there, it is down and locked.
LGCIUs
What the LGCIUs watch Proximity detectors report positions; the LGCIUs process them and pass them on.
Gear locks Each gear locked down, or locked up (uplocked).
Shock absorbers Compressed or extended: the flight or ground signal.
Gear doors Open or closed: extension or retraction is possible only with the doors fully open.
Cargo doors Selector valves, locking shaft, handle, safety shaft and sills; some detector faults show NON LOCKED.
Flap attachments Four flap disconnect detectors, processed and sent to the SFCCs.
Outputs Positions to ECAM and to many other systems.
Chapter 22 · Landing Gear and Nose Wheel Steering
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Proximity detectors everywhere feed the two units. On the gear they report each leg locked down or locked up, each shock absorber compressed or extended, and each door open or closed. The door signal matters: the gear can only be extended or retracted once the doors are fully open. The units also look after the cargo doors. Sensors on the manual selector valves, the locking shaft, the locking handle, the safety shaft and the door sills report to them, and if a unit detects an electrical failure in the locking shaft, handle or safety shaft switches, it shows that part as NON LOCKED. And they process four flap disconnect detectors and pass them to the slat flap control computers, without monitoring those computers themselves. Then everything goes out to ECAM and to other systems.
LGCIUs
Flight or ground: who is listening? A sample of systems using the shock absorber signal (some apply to certain serial numbers only).
System In flight On ground Gear lever Retraction possible Retraction inhibited Engine reversers (FADEC) Reverse inhibited Reverse available; FLEX available Cabin pressure Climb mode Pre-pressurisation and depressurisation APU fire No automatic extinguishing Automatic extinguishing Strobe lights (AUTO) On Off PTU Runs if green/yellow differ by more than 500 PSI Extra conditions (master levers, towing) Probe and window heat High level Low level, only with an engine running
Some functions need both LGCIUs to agree, others act on a single one: check the logic system by system.
Chapter 22 · Landing Gear and Nose Wheel Steering
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is why the flight or ground signal is so important. This table shows a sample of the systems that listen to it. On the ground the gear lever cannot retract the gear, the reversers are available and FLEX take-off thrust can be selected, the APU fire system extinguishes automatically, the strobes stay off in AUTO and the probes heat at a low level only with an engine running. In flight the reversers are inhibited, the cabin pressure controller is in climb mode, the APU fire system no longer fires the bottle by itself and the strobes come on. Notice the footnote. For some systems, ground needs both units to agree, for others a single unit saying flight is enough. So when one unit fails, different systems react differently, and that is worth remembering when you see odd effects after an L G C I U fault.
LGCIUs
Downlock, uplock and door signals Examples of systems that use the gear lock and door detectors.
Signal System Effect Gear downlocked FAC VLE shown on the PFD Gear downlocked GPWS "TOO LOW GEAR" when not downlocked Gear downlocked Brake fans Cooling available only with gear down Gear downlocked Taxi and take-off lights Inhibited when not downlocked Gear downlocked LGCIU Doors close after DOWN is selected Gear uplocked LGCIU Doors close after UP is selected Doors fully open LGCIU Gear extension or retraction possible
For door closing and gear movement one valid detector output is enough.
Chapter 22 · Landing Gear and Nose Wheel Steering
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The lock and door detectors drive their own set of users. When the gear is down and locked, the flight augmentation computers show the gear extended speed, V L E, on the primary flight display, and the ground proximity system expects the gear, giving TOO LOW GEAR if it is not down when it should be. The brake fans can only run with the gear down, and the taxi and take-off lights are inhibited when the gear is not locked down. Inside the gear system itself, the doors only close once the gear is locked in the selected position: downlocked after a DOWN selection, uplocked after an UP selection. And the gear can only move when the doors are fully open. For those gear control functions, one valid detector output is enough, which keeps the system working after a single sensor failure.
Abnormal
Gravity extension G E A R G E A R GRAVITY GEAR EXTN PULL & TURN 1 Pull and turn 3 turns clockwise 2 Cut-off valve shuts gear hydraulics isolated from green and depressurised 3 Uplocks release doors and gears unlocked 4 Gravity drops the gear springs help the mains lock, airflow helps the nose 5 Doors stay open reset possible in flight if green is available Pull and turn the crank 3 turns clockwise: hydraulics isolated, locks released, the gear falls. The doors stay open.
Chapter 22 · Landing Gear and Nose Wheel Steering
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the normal system cannot lower the gear, for example after a green hydraulic failure or a loss of electrical power, the crew uses gravity extension. Turning the crank does three things. It isolates the gear hydraulics from the green system, it unlocks the doors and the main and nose gear uplocks, and it lets gravity drop the gear into the extended position. Watch the gear fall now. The main gears need help to lock at the end, and the downlock springs provide it. The nose gear falls forward into the airflow, so aerodynamic forces push it into lock. Notice that the doors remain open afterwards, because nothing is driving them closed. If green pressure is available, the system can be reset in flight after a training extension.
Abnormal
The gravity extension crank On the centre pedestal : PULL & TURN Pull out, then turn clockwise 3 turns The cut-off valve shuts and depressurises the gear system Main gear: locking springs ; nose gear: airflow Doors remain open ; reset possible with green availableG E A R G E A R GRAVITY GEAR EXTN PULL & TURN Crank (centre pedestal) pull it out, then turn it clockwise for 3 turns green supply cut-off valve SHUT gear system depressurised Then uplocks release gravity drops the gear doors remain open Use it when hydraulics or electrics cannot lower the gear normally
Chapter 22 · Landing Gear and Nose Wheel Steering
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The crank lives on the centre pedestal, under a panel marked GRAVITY GEAR EXTN, PULL and TURN. To use it, pull the handle out, then turn it clockwise three full turns. The first thing the crank does is close the cut-off valve, which shuts off green pressure to the gear system and depressurises it. That is important: the gear actuators must not be holding the gear up while you are trying to let it fall. Then the doors and gear uplocks are released, and the gear drops. Expect the doors to stay open, so the WHEEL page will show the door symbols open in amber after landing gear down. A practical point: you use the crank when the hydraulic or electrical part of the normal system has failed, so it is purely mechanical from the cockpit.
Indications
The WHEEL page: gear and doors WHEEL UP LOCK L/G CTL 85 1 90 2 80 3 85 4 °C REL °C REL AUTO BRK MED TAT +19 °C SAT +18 °C 14 H 05 GW 64200 KG 1 2 3 4 5 1 Gear triangles two per leg, one from each LGCIU 2 Door symbols green closed · amber moving or open 3 UP LOCK (amber) uplock engaged although the gear is down 4 L/G CTL (amber) lever and gear disagree while the gear moves 5 Lower half brakes, anti-skid and autobrake: next lesson
Chapter 22 · Landing Gear and Nose Wheel Steering
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the ECAM WHEEL system page. The upper half belongs to this lesson. Each gear has two triangles side by side, and each triangle reports what one control unit detects, so two triangles means two independent opinions. Above each gear, the door symbols show the bay doors: a green line when the door is closed and locked up, an amber line at an angle while it moves, and amber hanging straight down when fully open. Tag three shows UP LOCK in amber: the uplock of that gear is engaged although the gear is down and locked. Tag four, L G CTL in amber, means the lever and the gear position disagree. Both come with an ECAM caution. N W STEERING also lives here, and we meet it with steering. The lower half, brakes, anti-skid and autobrake, belongs to the next lesson.
Indications
Reading the gear triangles WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL Cruise: gear up no triangles, doors closed in green WHEEL L/G CTL 60 1 65 2 60 3 55 4 °C REL °C REL Gear in transit red triangles, doors open in amber, L/G CTL while moving WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL Down and locked green triangles, doors closed again WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL One LGCIU failed amber crosses; one green triangle per gear is enough Green: downlocked · red: in transit · none: uplocked · amber cross: that LGCIU has failed.
Chapter 22 · Landing Gear and Nose Wheel Steering
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us practise reading the triangles. In cruise the gear is up, so there are no triangles at all, and the doors are green, closed. During travel, each unit sees the gear in transit, so the triangles are red and the doors hang open in amber. In this snapshot L G CTL is also showing, because lever and gear disagree while the gear moves. Once the gear is down and locked, all six triangles are green and the doors close again. Now the failure case: one of the two units has failed. Whichever unit it is, an amber cross replaces the right-hand triangle on each gear. Is the gear down? Yes. The rule is that one green triangle on each gear is enough to confirm that gear is down and locked. That is the answer to a very common interview question.
Indications
UP LOCK, L/G CTL and the ferry memo UP LOCK amber + caution: uplock engaged with gear downlockedL/G CTL amber + caution: lever and gear disagreeL/G CTL shows only while the gear is moving Red arrow + red warning: not down in landing configuration FLT L/G DOWN green memo: ferry flight with the gear downWHEEL UP LOCK 60 1 65 2 60 3 55 4 °C REL °C REL UP LOCK: the uplock is engaged although the gear is down FLT L/G DOWN memo: ferry flight with the gear down L/G CTL (amber, with a caution) lever and gear position disagree; shown only while the gear is moving to the selected position
Chapter 22 · Landing Gear and Nose Wheel Steering
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few more legends complete the gear picture. UP LOCK appears in amber above a gear, with an ECAM caution, if that gear's uplock is engaged when the gear is down and locked. It means the uplock has not released or reset as it should. L G CTL appears in amber, also with a caution, when the lever position and the gear position do not agree, and it only appears while the gear is travelling to the selected position. The most serious is the red arrow next to the lever with a red ECAM warning: the gear is not locked down and you are in landing configuration. Finally a memo. FLT L G DOWN in green appears if the aircraft is operated in ferry flight conditions with the gear down, a reminder of the extra drag and lower speed limits.
Nose wheel steering
Steering architecture CAPT handwheel F/O handwheel Rudder pedals Autopilot + added together PEDALS DISC pb on either handwheel: pedal and autopilot orders cut off BSCU order → steering angle limited by ground speed A/SKID & N/W STRG: ON towing lever: normal one engine running aircraft on ground AND STEERING SERVO VALVE electrical order pressure allowed yellow actuator nose wheel Yellow hydraulics move the actuator; the BSCU decides how far.
Chapter 22 · Landing Gear and Nose Wheel Steering
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now nose wheel steering. A hydraulic actuating cylinder turns the nose wheel. The yellow system supplies its pressure, and electrical signals from the brake and steering control unit, the B S C U, control it. The unit takes orders from three sources. The captain's and first officer's handwheels, whose orders are added together, the rudder pedals, and the autopilot, for example during an automatic roll out. Pedal and autopilot orders pass through a switch that the pedals disconnect button on either handwheel can open. The unit converts the order into a nose wheel angle, limits it with ground speed, and drives the steering servo valve. But yellow pressure only reaches the steering when four conditions are met together, which we will list in a moment.
Nose wheel steering
Steering angle falls with speed Handwheel: 75° up to 20 kt , zero at 80 kt Pedals: 6° up to 40 kt , zero at 130 kt Worked example: handwheel at 60 kt → 75 × (80 − 60) ÷ 60 = 25° Pedals at 85 kt → 6 × (130 − 85) ÷ 90 = 3° High-speed steering: pedals , small angles 0° 20° 40° 60° 80° 0 20 40 60 80 100 120 140 handwheel: 75° up to 20 kt, zero at 80 kt pedals: 6° up to 40 kt, zero at 130 kt 60 kt: 25° Ground speed (kt) Max nose wheel angle Above 80 kt only the pedals steer; above 130 kt neither
Chapter 22 · Landing Gear and Nose Wheel Steering
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The steering angle the unit allows depends on ground speed and on where the order comes from. With the handwheel you get up to seventy five degrees either way, but only up to twenty knots. From there the limit falls in a straight line to zero at eighty knots. The rudder pedals give a much smaller angle, six degrees, held up to forty knots and falling to zero at one hundred and thirty knots. Let us work two examples. At sixty knots, the handwheel limit is seventy five times twenty over sixty, which is twenty five degrees. At eighty five knots, the pedal limit is six times forty five over ninety, which is three degrees. That is why you taxi round tight corners with the handwheel, and keep straight on the take-off roll with the pedals.
Nose wheel steering
When does the steering work? A/SKID & N/W STRG switch ON Towing lever in normal positionAt least one engine runningAircraft on the ground Towing: up to 95° ; a cam centres the wheel after lift-off A/SKID & N/W STRG switch ON Towing control lever in normal position At least one engine running Aircraft on the ground AND yellow pressure to steering Angles handwheel: up to 75° each way towing (steering disconnected): up to 95° each way After lift-off a cam inside the leg centres the nose wheel
Chapter 22 · Landing Gear and Nose Wheel Steering
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Watch the steering at work. The B S C U turns the pilot's order into an angle and moves the steering servo valve. Yellow pressure goes to one side of the actuator, which pushes, and the nose wheel turns. When the order is removed, the system centres the wheel again. Pressure only reaches the actuator when four conditions are true together: the A SKID and N W STRG switch is on, the towing control lever is in its normal position, at least one engine is running, and the aircraft is on the ground. For towing, the ground crew moves a lever on a box on the nose gear, which disconnects the steering, and the tug can then turn the wheel up to ninety five degrees each way. After lift-off, a cam inside the leg centres the nose wheel, ready for retraction.
Nose wheel steering
Steering indications and the PEDALS DISC button N/W STEERING amber: steering lostCauses: steering failure, both BSCU channels , yellow low pressure , switch OFF Y beside it: green (yellow OK) or amber (yellow low pressure)NW STRG DISC memo: towing position (green, amber with an engine running)PEDALS DISC pb: removes pedal control while pressedWHEEL N/W STEERING Y 60 1 65 2 60 3 55 4 °C REL °C REL N/W STEERING amber · Y amber: yellow low pressure NW STRG DISC engines not running NW STRG DISC at least one engine running Memo: steering selector in the towing position Amber once an engine runs: a reminder before taxi
Chapter 22 · Landing Gear and Nose Wheel Steering
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do you know steering is lost? The WHEEL page shows N W STEERING in amber. The causes are a failure of the steering system, a failure of both B S C U channels, a yellow hydraulic low pressure, or the A SKID and N W STRG switch selected off. Beside the legend a Y tells you about the hydraulics: green if the yellow system is fine, so the problem is elsewhere, and amber if yellow pressure is low. There is also a memo. NW STRG DISC appears when the steering selector is in the towing position. It is green with the engines stopped, and turns amber once an engine is running, warning you that the tow bar setting is still selected. Finally, the pedals disconnect button on each handwheel removes pedal control of the nose wheel while you hold it pressed, useful during the rudder check before take-off.
Summary
Landing gear in one page UP DOWN LDG GEAR UNLK UNLK UNLK WHEEL 60 1 65 2 60 3 55 4 °C REL °C REL G E A R G E A R GRAVITY GEAR EXTN PULL & TURN GREEN gear and doors YELLOW nose wheel steering Gear Mains retract inboard, nose forward. Green hydraulics, sequenced by two LGCIUs that swap after each retraction.
Protection Safety valve shuts above 260 kt (ADR 1, ADR 3). Lever locked DOWN on the ground.
Indications LDG GEAR panel: LGCIU 1 only. WHEEL page: both. One green triangle per gear is enough.
Gravity Pull and turn 3 turns: cut-off valve shuts, gear falls, doors stay open.
Flight / ground Shock absorber detectors via the LGCIUs drive reversers, pressurisation, APU fire and more.
Steering Yellow, BSCU. Handwheel 75° to 20 kt, pedals 6° to 40 kt. Four conditions.
Chapter 22 · Landing Gear and Nose Wheel Steering
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. The main gears retract inboard and the nose gear forward, all powered by green hydraulics and sequenced electrically by two control units, which swap over after each retraction. A safety valve fed by air data references one and three shuts off the gear supply above two hundred and sixty knots, and an interlock locks the lever down on the ground. The LDG GEAR panel uses unit one only, the WHEEL page uses both, and one green triangle per gear is enough. Gravity extension is pull, turn three times, and expect the doors to stay open. The shock absorber detectors give the flight or ground signal to many systems. And steering is yellow, controlled by the B S C U, with angle limits that shrink as speed rises. Next lesson: the brakes.