A320 Aircraft Systems · Chapter 24
Lights Flight deck lighting, the exterior lights and their automatic logic, the emergency lighting that guides passengers out, and the cabin signs.
Lights: see, be seen, and find the way out EXT LT · INT LT · EMER EXIT LT · SIGNS © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to lights. It sounds like a simple chapter, and in a way it is, but the examiner loves its details: which lights go off by themselves when the gear retracts, what AUTO means on the strobes, what the emergency lights do in the ARM position, and when the cabin signs come on without anyone touching a switch. We will start inside, with the flight deck lighting and the annunciator light test. Then we go outside, switch by switch along the EXT LT panel. Then we look at the emergency lighting that guides passengers to the exits in the dark, and finish with the cabin signs and their automatic logic.
Lesson roadmap
Lights in four parts ATA 33 . Most of it is switches, but the automatic logic is what you are tested on.
1 · Flight deck Integral, flood, dome and reading lights, the INT LT panel and the ANN LT test.
2 · Exterior The EXT LT panel: beacon, strobes, nav and logo, wing, landing, nose and turn-off lights.
3 · Emergency Escape path marking, EXIT signs, overhead lights, slide lights and the EMER EXIT LT switch.
4 · Signs SEAT BELTS and NO SMOKING / NO PED in AUTO, the 11 300 ft logic and the memos.
Chapter 24 · Lights
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the lights. Part one is the flight deck: the integral lighting behind every panel, the flood and dome lights, the reading and map lights, and the annunciator light switch, with its test position. Part two goes outside, along the EXT LT panel: the beacon, the strobes, the navigation and logo lights, the wing scan lights, the landing lights, the nose lights and the runway turn-off lights, and what each of them does by itself. Part three is the emergency lighting in the cabin, the escape path marking, exit signs and overhead lights, and the EMER EXIT LT switch, whose ARM position is a classic exam question. Part four is the cabin signs, their AUTO logic, and what happens when the cabin altitude climbs too high.
Overview
The A320 at night BEACON red, flashing: top and bottom of the fuselage STROBE white, synchronised: each wing tip + below the tail cone NAV & LOGO each wing tip and the tail cone; logo lights on the stabiliser WING scan lights on the fuselage sides: wing leading edge and engine intake LAND (L / R) retractable landing lights NOSE taxi and take-off lights on the nose gear strut RWY TURN OFF light to the sides ahead; off when the gear retracts Each light has one switch on the EXT LT panel; several also have automatic logic
Chapter 24 · Lights
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us walk round the aeroplane at night. On top of the fuselage and underneath it are the two red flashing beacons. On each wing tip, and in the tail cone, are the navigation lights, with the white strobes next to them on the wings and below the tail cone. On the upper surface of each horizontal stabiliser are logo lights, aimed at the company logo on the fin. On each side of the fuselage a scan light shines back along the wing leading edge and onto the engine air intake, so you can check for ice. Then there are the two retractable landing lights, left and right. And on the nose gear are the taxi and take-off lights, with the runway turn-off lights shining out to the sides. One switch each on the overhead, and several of them have an automatic mind of their own.
Part 1 · Flight deck
Lighting the flight deck Integral lighting in every panel and instrument (not the display units), all dimmableFlood lights and spot lights for work surfaces and consolesTwo dimmable dome lights : shadow-free general light On batteries only : just the right-hand dome light Reading, map holder, console, briefcase and floor lights for each pilot; the standby compass is lit overhead panel 1 1 2 3 4 4 5 6 6 7 7 1 dome · 2 pedestal flood · 3 glareshield · 4 console/floor · 5 compass · 6 reading · 7 map
Chapter 24 · Lights
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Inside the flight deck there are two families of light. Integral lighting is built into every instrument and panel, except the display units, which have their own brightness. You can dim all of it. Flood and spot lights then light the work surfaces and the side consoles. For the cockpit as a whole there are two dimmable dome lights in the ceiling, giving shadow-free light. Here is a detail worth remembering: when the batteries alone are supplying power, only the right-hand dome light works. Each pilot also has a reading light, a lit map holder, and lighting for the side console, the briefcase stowage and the floor. Lights under the glareshield light the centre instrument panel, a flood light in the middle of the overhead panel lights the pedestal, and the standby compass has its own integral light.
Part 1 · INT LT panel
The INT LT panel INT LT OVHD INTEG LT OFF BRT ICE IND & STBY COMPASS ON OFF DOME BRT OFF DIM ANN LT TEST DIM BRT READING LT OFF BRT OVHD INTEG LT overhead panel integral lighting: on/off, brightness ICE IND & STBY COMPASS standby compass light (and ice indicator, some a/c) DOME BRT / DIM / OFF: both dome lights ANN LT TEST / BRT / DIM: every annunciator light READING LT one per side: on/off, brightness Battery power only: just the right-hand dome light stays on. Shown: DOME OFF, ANN LT BRT.
Chapter 24 · Lights
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The main interior lighting controls are on the INT LT panel on the overhead. The OVHD INTEG LT knob switches on the integral lighting of the overhead panel itself and sets its brightness. The ICE IND and STBY COMPASS switch turns on the standby compass light, and on aircraft that have one, the light of the external ice indicator. The DOME switch has three positions: BRT, both dome lights bright; DIM, both dim; and OFF. The ANN LT switch controls every annunciator light in the cockpit, that is, every lit legend on every pushbutton. BRT is normal; DIM reduces them all to the same lower level for night flying; and TEST lights them all, which we will look at next. To the side, each pilot has a READING LT knob that switches his reading light on and sets its brightness.
Part 1 · Annunciator test
ANN LT: BRT, DIM and TEST TEST : every flight deck annunciator light comes onThe FCU windows show 8s DIM : all annunciators dimmed to one level; BRT : normalDuring the test do not use ECAM/ND transfer or DMC switching A legend that stays dark at TEST: a failed bulb, not a normal system ANN LT at TEST ANN LT TEST DIM BRT every annunciator lights FAULT OFF FAULT ON FAULT OVRD FAULT OFF ON FCU 888 888 88888 8888 TEST all annunciator lights on; FCU windows show 8s BRT normal brightness DIM reduced brightness, all lights at one level During the test: do not switch ECAM/ND or the DMCs.
Chapter 24 · Lights
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The annunciator light test is part of every cockpit preparation. Set ANN LT to TEST and look around: every annunciator light in the cockpit should come on, FAULT lights, OFF lights, ON lights, OVRD lights, all of them, and the liquid crystal windows on the flight control unit show a row of eights. Any legend that stays dark has a failed light, and you cannot trust it to warn you later. While the switch is at TEST, do not reconfigure the displays, so no ECAM or ND transfer and no DMC switching. When you have finished, set the switch back to BRT for normal brightness, or DIM, which lowers every annunciator to the same reduced level, for a dark cockpit at night.
Part 1 · Other controls
Where the other lighting controls are Location Control What it does Pedestal FLOOD LT MAIN PNL Flood lighting of the main instrument panel: on/off and brightness Pedestal INTEG LT MAIN PNL & PED Integral lighting of the main instrument panel and the pedestal Pedestal FLOOD LT PED Pedestal flood lighting Glareshield Two knobs Integral lighting of the glareshield; brightness of the FCU displays Main panel (each side) CONSOLE/FLOOR Side console, briefcase and floor lights: BRT, DIM or OFF Lateral window Map light switch + knob Map light for each pilot Maintenance panel AVIONICS COMPT LT AUTO: avionics compartment light follows the door; ON: lit
Chapter 24 · Lights
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The rest of the lighting controls are spread around the cockpit, close to what they light. On the pedestal there are three knobs: FLOOD LT MAIN PNL for the flood lighting of the main instrument panel, INTEG LT MAIN PNL and PED for the integral lighting of the main panel and the pedestal, and FLOOD LT PED for the pedestal flood light. On the glareshield, one knob sets the glareshield integral lighting and another the brightness of the FCU displays. On each side of the main instrument panel is a CONSOLE FLOOR switch, bright, dim or off, for the side console, briefcase and floor lights. On each lateral window are the map light controls. And on the maintenance panel, the AVIONICS COMPT LT pushbutton: in AUTO, the avionics compartment light is controlled by the opening of its door; ON lights it permanently.
Part 2 · EXT LT panel
The EXT LT panel EXT LT STROBE ON OFF A U T O BEACON ON OFF WING ON OFF NAV & LOGO 2 OFF 1 RWY TURN OFF ON OFF — LAND — L R ON OFF RETRACT NOSE T.O OFF TAXI STROBE ON · AUTO (main gear not compressed) · OFF BEACON ON / OFF: two red flashing lights WING ON / OFF: wing and engine scan lights NAV & LOGO ON / OFF, or 2 · 1 · OFF with dual nav lights RWY TURN OFF ON / OFF; off when the gear retracts LAND L / R ON (extend, lit when fully out) · OFF · RETRACT NOSE T.O (taxi + take-off) · TAXI · OFF Shown: BEACON ON, NAV & LOGO at 2, STROBE AUTO, LAND at RETRACT, the rest OFF
Chapter 24 · Lights
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the EXT LT panel on the overhead. In the top row, from the left: STROBE, with ON, AUTO and OFF; BEACON, ON or OFF; WING, ON or OFF, for the wing and engine scan lights; and NAV and LOGO. On aircraft with a single set of navigation lights, NAV and LOGO is simply ON or OFF; with dual navigation lights it has three positions, 2, 1 and OFF, to choose which set. In the bottom row: RWY TURN OFF, ON or OFF; the two LAND selectors, left and right, each with ON, OFF and RETRACT; and the NOSE switch with T O, TAXI and OFF. Notice the extra position on the landing light selectors: OFF and RETRACT are not the same thing, and we will see why. Let us now take the lights one by one.
Part 2 · Anti-collision lights
Beacon and strobes BEACON : two red flashing lights, top and bottom of the fuselageSTROBE : three synchronised white strobes: each wing and below the tail coneAUTO : strobes on when the main gear is not compressed STROBE OFF in flight : green STROBE LT OFF memo LED lights (some aircraft): a blue light flashes when replacement is due Beacon and strobes beacon (top) beacon (bottom) strobe below the tail cone BEACON ON two red flashing lights, top and bottom STROBE ON three white strobes flash together: one on each wing, one below the tail cone STROBE AUTO on when the main gear is not compressed STROBE OFF in flight: STROBE LT OFF memo (green) LED wear blue light flashes: plan replacement (some a/c)
Chapter 24 · Lights
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The anti-collision lights come in two kinds. The BEACON switch controls two red flashing beacons, one on top of the fuselage and one at the bottom. The STROBE switch controls three white strobes that flash together, one on each wing and one below the tail cone. Strobes are very bright, so the switch has an AUTO position: in AUTO they come on automatically when the main landing gear is not compressed, that is, once the aircraft is airborne, and they go off again after touchdown. ON forces them on, and OFF switches them off. If the strobe switch is OFF in flight, the green memo STROBE LT OFF appears on the E W D, a reminder. On aircraft with LED lights, a small blue light under each strobe flashes when it is wearing out and replacement should be planned.
Part 2 · Position lights
Navigation and logo lights NAV : on each wing and in the APU tail cone; single or dual (2 · 1 · OFF)LOGO : on the upper surface of each horizontal stabiliser , lighting the finLogo lit with NAV & LOGO on and main gear compressed …or, depending on the aircraft, flaps extended (≥ 15° on some) or slats extended LED nav lights: blue wear light flashes when NAV & LOGO is ON NAV and LOGO wing tip wing tip tail cone logo lights Logo lights light the fin when NAV & LOGO is on and: • the main landing gear is compressed (on the ground), or • depending on the aircraft: flaps extended (≥ 15° on some) or slats extended Dual nav lights (some a/c): switch positions 2 · 1 · OFF LED wear: a blue light flashes when replacement is due
Chapter 24 · Lights
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The navigation lights show other pilots where you are and which way you are pointing. There is a light on each wing tip and one in the APU tail cone. Some aircraft have dual navigation lights; then the switch has positions 2, 1 and OFF, so you can select the second set if the first fails. The same switch controls the logo lights. These sit on the upper surface of each horizontal stabiliser and shine on the company logo on the fin. They do not shine all the time: they come on when the main landing gear is compressed, so on the ground, or, depending on the aircraft, when the flaps are extended, at least fifteen degrees on some, or the slats are extended. In other words, low and slow, near airports, where being recognised matters. Once you are clean in cruise, the logo goes dark.
Part 2 · Landing and taxi lights
Landing, nose and turn-off lights LAND ON : lights extend and come on when fully extended OFF : off but still extended · RETRACT : off and retractedNOSE (on the nose gear strut): T.O = taxi + take-off lights, TAXI = taxi light onlyNose and RWY TURN OFF lights go off automatically when the gear retracts LDG LT memo while a landing light is extendedLanding, nose and turn-off lights T.O and TAXI RWY TURN OFF RWY TURN OFF LAND L LAND R LAND ON lights extend, come on when fully extended LAND OFF lights off, stay extended LAND RETRACT off and retracted NOSE T.O taxi + take-off lights; TAXI: taxi only Gear up nose lights and RWY TURN OFF go off by themselves LDG LT memo (green): a landing light is extended
Chapter 24 · Lights
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The landing lights retract into the aircraft when they are not in use. Set a LAND selector to ON and the light extends, and it comes on only when it is fully extended. Set it to OFF and the light goes out but stays extended, in the airflow. Only RETRACT switches it off and stows it. As long as a landing light is extended, the green memo LDG LT is shown, so you will notice if one is left hanging out in cruise. The NOSE switch controls two lights attached to the nose gear strut: at T O, both the taxi and the take-off lights come on; at TAXI, only the taxi light. The RWY TURN OFF switch lights the sides of the taxiway ahead. And here is the automatic part: the nose lights and the runway turn-off lights go off by themselves when the landing gear retracts.
Part 2 · Ice inspection
WING: the scan lights Two beam lights , one on each side of the fuselage They light the wing leading edge and the engine air intake Purpose: see ice accretion at night Switch WING : ON / OFF Ice indicator light (some aircraft): ICE IND & STBY COMPASS switch WING: scan lights for ice Two beam lights, one on each side of the fuselage. They light the wing leading edge and the engine air intake, so the crew can see ice accretion at night. Ice indicator light: ICE IND & STBY COMPASS sw (some a/c).
Chapter 24 · Lights
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The WING switch controls the wing and engine scan lights. There are two beam lights, one on each side of the fuselage. Each one shines outwards, onto the leading edge of the wing and onto the engine air intake. Why? Because at night you cannot see whether ice is building up on the wing or around the engine intake, and these are exactly the places you need to watch in icing conditions. A quick look out of the side window with the wing lights on tells you whether there is ice. On aircraft with an external ice indicator, its light is switched with the ICE IND and STBY COMPASS switch on the INT LT panel, which we met in part one.
Part 2 · Putting it together
What the lights do by themselves Event Automatic change Why it matters Lift-off: main gear no longer compressed STROBE in AUTO comes on No action needed after take-off Gear retraction NOSE (taxi, T.O) and RWY TURN OFF go off Switches may still be ON: they light again when the gear comes down Flaps/slats retracted in flight (gear up) LOGO goes off (depending on the aircraft)Logo lit near the ground, dark in cruise LAND selector OFF Light off but still extended ; LDG LT memo stays Select RETRACT to stow it Touchdown: main gear compressed STROBE in AUTO goes off ; LOGO on Strobes do not dazzle on the taxiway STROBE OFF in flight STROBE LT OFF memo A reminder, not a failure
Chapter 24 · Lights
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the automatic behaviour in one table, because this is where exam questions come from. At lift-off, when the main gear is no longer compressed, the strobes in AUTO come on. When the gear retracts, the nose lights and the runway turn-off lights go off, even if their switches are still on, and they will come back on when the gear is lowered again. When the flaps and slats are retracted in flight, the logo lights go off on aircraft with that logic. A landing light selected to OFF is dark but still extended, and the LDG LT memo stays until you select RETRACT. At touchdown, with the main gear compressed, strobes in AUTO go off and the logo lights come on. And if you switch the strobes off in flight, the STROBE LT OFF memo reminds you.
Part 2 · ECAM
Lighting memos LDG LT : at least one landing light is extendedSTROBE LT OFF : STROBE switch OFF in flightSEAT BELTS , NO SMOKING or NO PED : those signs are onAll in green : reminders Classic trap: LAND at OFF still gives LDG LT E/WD · memo area LDG LT STROBE LT OFF SEAT BELTS NO SMOKING NO PED LDG LT at least one landing light extended STROBE LT OFF STROBE switch OFF in flight SEAT BELTS the seat belt signs are on NO SMOKING / NO PED those signs are on (customisation) All green: reminders, not failures.
Chapter 24 · Lights
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Lighting adds a handful of green memos to the E W D. LDG LT appears when at least one landing light is extended, whether it is lit or not. STROBE LT OFF appears when the strobe switch is off in flight. And when the cabin signs are on, the memo area shows SEAT BELTS, NO SMOKING, or NO PED, depending on how the aircraft is customised. These memos are all green: they are reminders of a configuration, not failures. Here is a classic trap. In climb, a pilot turns the landing lights to OFF instead of RETRACT. The lights go dark, but they are still extended in the airflow, and the LDG LT memo stays on the E W D. The memo is telling you to finish the job and select RETRACT.
Part 3 · Emergency lighting
Finding the way out Proximity emergency escape path marking : floor path and exit markersOverhead emergency lights and EXIT signs Lavatory auxiliary lights : always onOverwing escape route and slide lights: automatic when the slide is armed and the door or exit opensInternal batteries: at least 12 min for electrical paths and markers Emergency lighting in the cabin floor path (proximity marking) · EXIT signs and markers · overhead lights Proximity escape path marking floor strips and exit markers Overhead emergency lights and EXIT signs Lavatory auxiliary lights always on Overwing escape route and slide lights automatic: slide armed and door/exit open Internal batteries electrical paths and markers: at least 12 min
Chapter 24 · Lights
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the cabin fills with smoke or the power fails, passengers must still find the exits. The emergency lighting system has several parts. The proximity emergency escape path marking runs along the floor of the aisle, with exit markers, so people crawling low in smoke can follow it to an exit. Overhead emergency lights and illuminated EXIT signs light the cabin from above. The lavatories have auxiliary lights that are always on. Outside, the overwing escape route lights and the escape slide lights come on automatically when the slide is armed and the door or emergency exit is opened, powered by their own internal batteries. On aircraft with electrical escape paths or exit markers, internal batteries keep them lit for at least twelve minutes, long enough for an evacuation.
Part 3 · Controls
EMER EXIT LT: ON, ARM, OFF SIGNS SEAT BELTS ON OFF NO SMOKING ON OFF A U T O EMER EXIT LT OFF ON OFF ARM Purser panel LIGHT ■ EMER LIGHT EMER pb ON overhead emergency lights, EXIT signs and proximity marking on ARM normal: they come on by themselves if power is lost (next slide) OFF all off; amber EMER EXIT LT OFF light on LIGHT EMER purser panel: same as ON, whatever the switch position Shown: SEAT BELTS and NO SMOKING at AUTO (middle), EMER EXIT LT at ARM Some aircraft fit the switch the other way up (OFF at the top). Normal position: ARM . OFF lights the amber EMER EXIT LT OFF light. LIGHT EMER on the purser panel works whatever the switch position.
Chapter 24 · Lights
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The emergency lighting is controlled from the EMER EXIT LT switch, next to the cabin signs on the overhead. It has three positions. ON switches on the overhead emergency lights, the EXIT signs and the proximity marking straight away. OFF switches them off, and an amber EMER EXIT LT OFF light comes on, so the crew cannot forget it. ARM is the normal position for flight: the lights stay off while the aircraft is powered normally, but come on by themselves if the power they depend on is lost. In the cabin, the purser has a LIGHT EMER pushbutton that does the same as ON, whatever the position of the cockpit switch, so the cabin crew can light the escape routes themselves. Note that on some aircraft the switch is fitted the other way up, with OFF at the top.
Part 3 · ARM logic
At ARM, what comes on when power is lost? Failure (switch at ARM) Overhead emergency lights EXIT signs Escape path / exit markers Normal aircraft electrical power lost ON ON ON DC SHED ESS BUS lost ON ON ON AC BUS 1 lost only ON off off Switch at ON (any power) ON ON ON Purser LIGHT EMER pb pressed ON ON ON Switch at OFF off; amber EMER EXIT LT OFF off off
Worked example: AC BUS 1 fails in cruise with the switch at ARM. Only the overhead emergency lights come on; the EXIT signs and floor marking stay off.
Chapter 24 · Lights
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table is the heart of the emergency lighting exam questions. With the switch at ARM, the triggers are slightly different for each group of lights. If the normal aircraft electrical power fails, or the DC SHED ESS bus fails, everything comes on: the overhead emergency lights, the EXIT signs and the escape path marking. But the overhead emergency lights have one extra trigger: they also come on if AC BUS 1 alone fails. So, a worked example: in cruise, AC BUS 1 is lost and the switch is at ARM. What does the cabin see? The overhead emergency lights come on, but the EXIT signs and the floor marking stay off, because neither the normal power nor the DC SHED ESS bus has been lost. Of course, the switch at ON, or the purser's LIGHT EMER button, lights everything regardless.
Part 4 · Cabin signs
The SIGNS panel SEAT BELTS : FASTEN SEAT BELT and RETURN TO YOUR SEAT signsNO SMOKING or EXIT : EXIT and NO SMOKING signs · NO PED : EXIT and NO MOBILEON · AUTO · OFF on each switchAUTO : on when the landing gear or the flaps/slats are extended (1, 2, 3 or FULL)A low tone chime as a sign goes on or off (CIDS programming) SIGNS SEAT BELTS ON OFF NO SMOKING ON OFF A U T O EMER EXIT LT OFF ON OFF ARM ON signs on in the cabin AUTO on when the landing gear OR flaps/slats are extended (position 1, 2, 3 or FULL) OFF signs off SEAT BELTS: FASTEN SEAT BELT + RETURN TO YOUR SEAT NO SMOKING / EXIT: EXIT + NO SMOKING · NO PED: EXIT + NO MOBILE A low chime sounds as a sign goes on or off (CIDS programming).
Chapter 24 · Lights
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The SIGNS panel has two switches. The SEAT BELTS switch lights the FASTEN SEAT BELT and RETURN TO YOUR SEAT signs. The second switch depends on the customer: a NO SMOKING switch, or an EXIT switch, which light the EXIT and NO SMOKING signs, or a NO PORTABLE ELEC DEVICE switch, which lights the EXIT and NO MOBILE signs. Each switch has three positions. ON: the signs are on. OFF: they are off. AUTO: the signs come on automatically when either the landing gear is extended or the flaps and slats are extended, in position 1, 2, 3 or FULL. So in AUTO the signs are on for take-off and landing and go off once the aircraft is clean. Depending on how the cabin system is programmed, a low chime sounds in the cabin each time a sign comes on or goes off.
Part 4 · Automatic signs
Cabin altitude and the signs Cabin altitude above 11 300 ft (± 350 ft) : all cabin signs on …except the NO PED signs Cabin lights also on (CIDS/CAM programming) Whatever the switch positions Non-smoker aircraft: NO SMOKING signs always on Cabin altitude above 11 300 ft 8 000 9 000 10 000 11 000 12 000 13 000 14 000 11 300 ft nominal may trigger as late as 11 650 ft or as early as 10 950 ft (± 350 ft) All cabin signs ON (not NO PED) and cabin lights (CIDS programming), whatever the switch positions Signs follow their switches Non-smoker aircraft: NO SMOKING signs always on.
Chapter 24 · Lights
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
There is one more automatic trigger, and it overrides the switches. If the cabin altitude climbs above eleven thousand three hundred feet, plus or minus three hundred and fifty, all the cabin signs come on, whatever the switch positions, except the NO PED signs. Depending on the cabin programming, the cabin lights come on too. Why? Because a cabin that high means a pressurisation problem, and passengers must be seated with belts fastened, ready for the oxygen masks. Let us work out the tolerance: three hundred and fifty feet either side of eleven thousand three hundred gives a band from ten thousand nine hundred and fifty to eleven thousand six hundred and fifty feet. So the signs may come on as early as ten thousand nine hundred and fifty feet. And on aircraft declared non-smoker, the NO SMOKING signs are simply always on.
Summary
Lights on one page Flight deck Integral + flood lighting, two dome lights (right one only on batteries ). ANN LT: TEST lights every annunciator and FCU 8s; BRT; DIM.
Anti-collision BEACON: 2 red, top and bottom. STROBE: 3 white, wings and tail cone; AUTO = main gear not compressed ; STROBE LT OFF memo.
Position and logo NAV on wing tips and tail cone (single or dual). LOGO on the stabiliser: gear compressed or flaps (≥ 15° some) / slats out.
Landing and taxi LAND: ON extends, lit when fully out; OFF stays extended ; RETRACT. NOSE T.O / TAXI and RWY TURN OFF off at gear retraction . LDG LT memo.
Emergency ARM: normal power or DC SHED ESS lost → all on; AC BUS 1 lost → overhead lights only . OFF: amber light. LIGHT EMER on purser panel. Batteries ≥ 12 min.
Signs AUTO: gear or flaps/slats extended. Cabin altitude > 11 300 ft ± 350 : all signs on except NO PED. Non-smoker: NO SMOKING always on.
Chapter 24 · Lights
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
To finish, the essentials. In the flight deck: integral and flood lighting, two dome lights with only the right one on batteries, and the ANN LT test that lights every annunciator. Outside: two red beacons, three white strobes that come on in AUTO when the main gear is no longer compressed, navigation lights on the wing tips and the tail cone, and logo lights that shine on the ground or with flaps or slats out. Landing lights extend when selected ON, stay extended at OFF, and stow only at RETRACT. Nose and turn-off lights go off when the gear retracts. For emergencies, the EMER EXIT LT switch at ARM lights everything if normal power or the DC SHED ESS bus is lost, but only the overhead lights for an AC BUS 1 failure. And the cabin signs come on in AUTO with gear or flaps out, and always above eleven thousand three hundred feet of cabin altitude.