A320 Aircraft Systems · Chapter 25
Navigation: ADIRS, Standby Instruments and Radio Navigation Where the A320 gets its air data, attitude and position, what backs them up, and how its radio navigation receivers are tuned.
ADIRS ON BAT IR 1 FAULT OFF OFF NAV ATT ADR 1 FAULT OFF IR 3 FAULT OFF OFF NAV ATT ADR 3 FAULT OFF IR 2 FAULT OFF OFF NAV ATT ADR 2 FAULT OFF 10 10 200 220 240 260 280 300 320 90 95 100 105 110 10000 1013 hPa BUGS LS + – ATT RST BARO ACTIVE STBY/CRS 118.700 121.800 VHF1 VHF2 VHF3 LOAD HF1 SEL HF2 AM STBY NAV NAV VOR ILS GLS MLS ADF BFO ON OFF ADR · IR · GPS VOR · ILS · DME · RA © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the navigation lesson. Every speed, altitude, attitude and position you see on the A320 displays starts in a few small units in the avionics bay called ADIRUs, fed by probes on the nose and by satellites overhead. In this lesson we will build that system from the probes up: the air data and inertial parts, the overhead panel, alignment, and what you switch when a unit fails. Then we look at the backups: the backup speed scale, the standby instrument and the compass. Finally we cover the radios: how the receivers are tuned, the radio management panel, the DDRMI and the radio altimeters with their callouts. These are the details that type-rating examiners love to ask.
Navigation
Our route through ATA 34 navigation ADIRS ON BAT IR 1 FAULT OFF OFF NAV ATT ADR 1 FAULT OFF IR 3 FAULT OFF OFF NAV ATT ADR 3 FAULT OFF IR 2 FAULT OFF OFF NAV ATT ADR 2 FAULT OFF 10 10 200 220 240 260 280 300 320 90 95 100 105 110 10000 1013 hPa BUGS LS + – ATT RST BARO SWITCHING ATT HDG CAPT 3 NORM F/O 3 AIR DATA CAPT 3 NORM F/O 3 EIS DMC CAPT NORM F/O ECAM/ND XFR CAPT NORM F/O ACTIVE STBY/CRS 118.700 121.800 VHF1 VHF2 VHF3 LOAD HF1 SEL HF2 AM STBY NAV NAV VOR ILS GLS MLS ADF BFO ON OFF ADIRS Three ADIRUs, probes, the overhead panel, alignment, switching, GPS and BUSS.
Standby The ISIS, its flags and functions, and the standby compass.
Radio navigation Tuning by the FMGC or the RMP, VOR, ILS, DME, ADF, markers and the DDRMI.
Radio altimeter Two RAs, which PFD shows which, and the automatic callouts.
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the navigation part of chapter thirty four. We start with the air data and inertial reference system, the ADIRS: three identical units, the probes that feed them, the overhead panel, alignment, the switching you use when one fails, the GPS that keeps them accurate, and the backup speed scale. Then the standby instruments: the integrated standby instrument, called the ISIS, and the old faithful magnetic compass. Third, radio navigation: how the receivers are tuned automatically, manually and in back-up, the radio management panel and the DDRMI. Finally, the radio altimeters and the height callouts you hear on every landing.
ADIRS architecture
Three ADIRUs, each an ADR and an IR Three identical ADIRUs : 1, 2 and 3Each has an ADR (air data) part and an IR (inertial reference) part Either part keeps working if the other fails Pitot and static pressures reach the ADR through air data modules (8 ADMs) One ADIRS panel on the overhead; a switching facility brings ADR 3 or IR 3 to either side Probes → ADMs (pitot, static) and direct (AOA, TAT) ADIRU 1 ADR 1 air data IR 1 inertial ADIRU 3 ADR 3 air data IR 3 inertial ADIRU 2 ADR 2 air data IR 2 inertial PFD · ND · FMGC · FADEC · ELAC · SEC · FAC FWC · SFCC · ATC · GPWS · CFDIU · CPC
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 has three identical air data and inertial reference units, the ADIRUs, numbered one, two and three. Each one is really two systems in one box. The upper part in this scene is the air data reference, or ADR, which works with pressures and temperatures. The lower part is the inertial reference, or IR, which senses the aircraft's motion. Either part can carry on working if the other one fails, so you can lose an IR and keep its ADR. Pitot and static pressure lines do not go straight into the units; small air data modules convert the pressures into numbers first, and there are eight of them. Angle of attack and temperature arrive electrically. Everything then flows out to the displays and to a long list of users.
ADIRS outputs
What the ADR and the IR supply ADR: air data reference IR: inertial reference Supplies barometric altitude, airspeed, Mach, angle of attack, temperature, overspeed warnings attitude, flight path vector, track, heading, accelerations, angular rates, ground speed, position Senses with pitot, static, AOA and TAT probes (pressures through ADMs) its own inertial sensors; position refined by GPS Lost in ATT mode? no: the ADR keeps working navigation data lost; only attitude and heading (heading entered by the crew) Mode selector OFF ADR data lost IR data lost Main users PFD, ND, FMGC, FADEC, ELAC, SEC, FAC, FWC, SFCC, ATC, GPWS, CFDIU, CPC same displays and systems
The selector at OFF de-energises the whole ADIRU, so both its ADR and its IR data are lost.
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table is worth learning by heart. The air data reference supplies barometric altitude, airspeed, Mach number, angle of attack, temperature and the overspeed warnings. The inertial reference supplies attitude, the flight path vector, track, heading, accelerations, angular rates, ground speed and the aircraft position. Notice that the two lists do not overlap: speed through the air comes from the ADR, speed over the ground from the IR. Now the trap. The IR mode selector has OFF, NAV and ATT. In ATT mode the IR loses its navigation data but the ADR is untouched. At OFF, the whole ADIRU is de-energised, so both the IR and the ADR data are gone, even though the selector looks as if it belongs only to the IR.
Sensors
Where the probes are Left side (looking from the left) CAPT pitot STBY pitot CAPT TAT CAPT AOA STBY AOA CAPT static F/O static STBY static Right side (looking from the right) F/O pitot F/O TAT F/O AOA F/O static CAPT static STBY static Pitot AOA vane Static port TAT probe 3 pitot probes · 6 static ports · 3 AOA vanes · 2 TAT probes, all electrically heated
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at the nose, where the air data comes from. There are four kinds of sensor. Three pitot probes measure total pressure: one for the captain, one for the first officer and one standby. Three angle of attack vanes, again captain, first officer and standby, stand out from the sides of the forward fuselage. Six static ports measure the outside static pressure; each static system has a port on each side of the fuselage, which helps cancel errors in a sideslip. And two total air temperature probes, one for the captain and one for the first officer. Every one of these sensors is electrically heated so that it cannot ice up, which is why probe heat matters so much on the A320.
Probes to ADIRUs
Which probes feed which ADIRU CAPTAIN probes ADIRU 1 Pitot CAPT ADM Static CAPT (L) ADM Static CAPT (R) ADM AOA CAPT TAT CAPT STANDBY probes ADIRU 3 Pitot STBY ADM Static STBY (L + R) ADM AOA STBY TAT CAPT (shared) ISIS direct to the standby instrument F/O probes ADIRU 2 Pitot F/O ADM Static F/O (L) ADM Static F/O (R) ADM AOA F/O TAT F/O pitot line static line electrical (data) 8 ADMs ADIRU 1 uses the CAPT probes · ADIRU 2 the F/O probes · ADIRU 3 the STBY probes and the CAPT TAT
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the probe schematic in our own colours. The rule is simple: ADIRU one uses the captain's probes, ADIRU two the first officer's probes, and ADIRU three the standby probes. There is one exception that examiners like: there is no standby temperature probe, so ADIRU three takes its temperature from the captain's TAT probe. Follow the pressure lines. Pitot and static pressures go to air data modules, which turn them into digital data for the ADIRU. Count them: three pitot modules and five static modules, eight in all. The angle of attack vanes and the TAT probes are electrical, so they go straight to their ADIRU. And notice that the standby pitot and static lines also go directly to the standby instrument, the ISIS.
Overhead panel
The ADIRS panel ON BAT light at the topThree IR pushbuttons, laid out 1, 3, 2 (ADIRU 3 in the middle) Three mode selectors : OFF · NAV · ATT Three ADR pushbuttons, also 1, 3, 2 Normal flight: selectors at NAV , all lights out ADIRS ON BAT IR 1 FAULT OFF OFF NAV ATT ADR 1 FAULT OFF IR 3 FAULT OFF OFF NAV ATT ADR 3 FAULT OFF IR 2 FAULT OFF OFF NAV ATT ADR 2 FAULT OFF 1 2 3 4 1 ON BAT 2 IR 1, 3, 2 pushbuttons 3 IR mode selectors 4 ADR 1, 3, 2 pushbuttons
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the ADIRS panel on the overhead, as fitted to most aircraft in this fleet. At the top is the ON BAT light. Below it is a row of three IR pushbuttons, then the three mode selectors, then a row of three ADR pushbuttons. Look at the order: one, three, two. ADIRU three sits in the middle because it can stand in for either side. In normal flight all three selectors are at NAV and every light on the panel is out, in keeping with the dark cockpit idea. So if you see any light on this panel in flight, something needs your attention. Let us take the pushbuttons and selectors one at a time.
IR, ADR and mode selector
Pushbutton lights and the mode selector IR or ADR FAULT (amber) with ECAM NAV IR (ADR) FAULT ; press: OFF, FAULT goes out IR FAULT flashing : attitude and heading may be recovered in ATT IR FAULT steady : the IR is lost ATT : attitude and heading only; heading entered on the MCDU and reset about every 10 min In flight, NAV → ATT or OFF : NAV mode is lost for the rest of the flight IR pushbutton FAULT OFF On lights out FAULT OFF FAULT flashing try ATT mode FAULT OFF FAULT steady IR lost FAULT OFF OFF IR switched off IR mode selector OFF NAV ATT ADIRU not energised: no IR and no ADR data OFF NAV ATT Normal: full inertial and full air data OFF NAV ATT Attitude and heading only; heading entered by crew In flight, NAV → ATT or OFF: NAV is lost for the rest of the flight
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each IR and ADR pushbutton is on with its lights out. Pressing it shows a white OFF and removes that part from service. An amber FAULT light comes on with an ECAM caution, NAV IR fault or NAV ADR fault, and pressing the button puts the FAULT light out. The IR FAULT light has a subtle code. If it flashes, the IR has lost its navigation function but attitude and heading may still be recovered by selecting ATT. If it is steady, the IR is lost. In ATT mode the IR gives only attitude, and heading if you enter it on the MCDU; that heading drifts, so you reset it about every ten minutes. And the big trap: in flight, moving a selector from NAV to ATT or OFF loses NAV mode for the rest of the flight.
ON BAT light
ON BAT: an ADIRU on the batteries Amber ON BAT : at least one ADIRU is supplied by the aircraft batteries Also lit for a few seconds at the start of a complete alignment Not lit for a fast alignmentOn the ground on battery: external horn , amber ADIRU and AVNCS lights on the EXT PWR panel Out: all ADIRUs on normal power, or all off ADIRS ON BAT Overhead: ADIRS panel EXT PWR panel (nose) ADIRU AVNCS On the ground only External horn sounds Lit whenever an ADIRU runs on the batteries Lit at least one ADIRU is supplied by the batteries Lit briefly start of a complete alignment (not a fast one) Out all ADIRUs on and on normal power, or all off
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ON BAT light tells you that at least one ADIRU is being supplied by the aircraft batteries rather than its normal power. You will see it briefly, for a few seconds, at the beginning of a complete alignment, as the system checks its battery back-up. During a fast alignment it does not come on. On the ground, this light has a partner outside the aircraft. If an ADIRU is running on the batteries, an external horn sounds and the amber ADIRU and AVNCS lights come on at the external power panel in the nose. That warns the ground crew that the batteries are being drained, for example when the aircraft has been left with the ADIRS on and no power. ON BAT is out when all three units are on normal power, or all are off.
Alignment
Alignment memos and REALIGN IRS IRS IN ALIGN X MN : minutes left to NAV, flight phase 1 or 2Engines stopped: green ; pulsing green if one IRS alignment is faulty An engine running: amber ; a faulty alignment becomes the IR NOT ALIGNED caution IR IN ATT ALIGN (green): IR aligning in ATT modeREALIGN IRS prompt on MCDU INIT: check the position, then validateE/WD memo area, flight phase 1 or 2 IRS IN ALIGN 7 MN engines stopped IRS IN ALIGN 7 MN one engine running IRS IN ALIGN 7 MN pulsing: an IRS is faulty IR NOT ALIGNED caution once an engine runs MCDU INIT page REALIGN IRS check the position, then validate IRS compare: last NAV position + latitude it estimates X MN = minutes left to NAV (1 < X < 10)
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
During alignment the memo area shows IRS IN ALIGN followed by the number of minutes left before NAV mode, between one and ten. Before any engine is started the memo is green, a calm reminder. If the alignment of one IRS is faulty, it pulses in green. Once an engine has been started, the memo turns amber, because you should not be taxiing with the inertial units still aligning, and a faulty alignment is now shown as the IR NOT ALIGNED caution instead. Another indication is IR IN ATT ALIGN, in green, when an IR is aligning in attitude mode. Finally, the MCDU INIT page may show a REALIGN IRS prompt. The IRS remembers its last NAV position and estimates the latitude itself, so it can detect a wrong position entry. Check the coordinates, then validate the prompt.
Older aircraft
The ADIRS CDU and the ALIGN light On older aircraft the ADIRS panel has a control and display unit DATA selector: TEST, TK/GS, PPOS, WIND, HDG (with minutes to alignment), STSSYS selector: OFF, 1, 3, 2; keyboard to enter position or heading (ATT)IR ALIGN steady: aligning; out: alignment complete ALIGN flashing : alignment fault, no position after 10 min , or entry more than 1° from the shutdown position ADIRS (older aircraft: control and display unit) N 48°36.2 E002°21.8 TEST TK/GS PPOS WIND HDG STS DATA OFF 1 3 2 SYS 1 N 2 3 W 4 5 E 6 7 S 8 9 ENT 0 CLR ON BAT IR 1 FAULT ALIGN OFF NAV ATT IR 3 FAULT ALIGN OFF NAV ATT IR 2 FAULT ALIGN OFF NAV ATT
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Older aircraft in the fleet have a different ADIRS panel, with a small control and display unit. The DATA selector chooses what the window shows: TEST lights everything up, TK GS shows true track and ground speed, PPOS the present position, WIND the true wind, HDG the true heading and the minutes left to complete alignment, and STS an action code. The SYS selector picks which ADIRU is displayed, and the keyboard lets you enter the present position, or a heading in ATT mode, as a back-up to the normal MCDU entry. On these aircraft each IR light has an ALIGN legend. Steady means aligning, out means aligned. Flashing means trouble: an alignment fault, no position entered within ten minutes, or an entered position more than one degree from where the aircraft was shut down.
Older aircraft
ADIRS CDU status messages With DATA at STS the window shows a message, scrolling every 2 s if there are several.
Message Meaning and action IR FAULT hard failure: select ATT if offered, or check the MMEL DELAY MAINT failure not affecting the IR: service when convenient ENTER PPOS enter (or check) the present position SELECT ATT hard IRU failure: select ATT mode EXCESS MOTION aircraft moved during alignment: it restarts by itself; keep still SWITCH ADR ADR invalid CHECK CK/BK check circuit breakers; with a FAULT light, check the BAT 1 load CDU FAULT · ENT MAG HDG CDU needs maintenance · enter the magnetic heading
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the DATA selector is at STS, the CDU window shows status messages, and if there is more than one, it scrolls to the next every two seconds. IR FAULT is a hard failure: select ATT if that is offered, or refer to the minimum equipment list. DELAY MAINT is a failure that does not affect the inertial function, so it can wait. ENTER PPOS asks you to enter, or check, the present position; and remember that confirming a wrong longitude will put the aircraft symbol in the wrong place on the NDs. SELECT ATT is a hard IRU failure. EXCESS MOTION means the aircraft moved during alignment, for example during loading; it restarts by itself, so keep the aircraft still. SWITCH ADR means the ADR is invalid. The last three are check breakers, CDU fault and enter magnetic heading.
Switching
ATT HDG and AIR DATA switching SWITCHING ATT HDG CAPT 3 NORM F/O 3 AIR DATA CAPT 3 NORM F/O 3 EIS DMC CAPT NORM F/O ECAM/ND XFR CAPT NORM F/O NORM ADIRU 1 → PFD 1, ND 1, DDRMI, VOR/DME ADIRU 2 → PFD 2, ND 2 CAPT 3 ADR 3 or IR 3 replaces ADR 1 or IR 1 F/O 3 ADR 3 or IR 3 replaces ADR 2 or IR 2 ATT HDG switches the IR · AIR DATA switches the ADR NORM PFD 1 ND 1 ND 2 PFD 2 ADIRU 1 ADIRU 3 ADIRU 2 standby: ready to replace 1 or 2 ADIRU 1 failed: both at CAPT 3 PFD 1 ND 1 ND 2 PFD 2 ADIRU 1 ADIRU 3 ADIRU 2 Memo ADIRS SWTG (on some aircraft) ATT HDG at CAPT 3 or F/O 3 → memo ADIRS SWTG; AIR DATA at CAPT 3 or F/O 3 too, unless BKUP SPD/ALT is on that side
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the pedestal, the SWITCHING panel has two selectors for the ADIRS. ATT HDG switches the inertial source, and AIR DATA switches the air data source. At NORM, ADIRU one feeds the captain's PFD and ND, the DDRMI and the VOR DME, and ADIRU two feeds the first officer's PFD and ND. ADIRU three waits in the middle. At CAPT three, the IR three or ADR three replaces number one; at F O three it replaces number two. Here is the worked example. ADIRU one fails completely. You set both ATT HDG and AIR DATA to CAPT three, and the captain's displays are back, now powered by ADIRU three. On many aircraft a memo, ADIRS SWTG, reminds you that the switching is not at NORM.
Speed checks
When is a speed difference a defect? Maximum differences used by maintenance (selected rows). Beyond them, a maintenance action is due.
Flight level Speed ADR 1 vs ADR 2 (PFDs) ADR 3 vs ADR 1 or 2 Standby vs any ADR Ground check – 6 kt · M 0.008 6 kt · M 0.008 6 kt FL 100 250 kt 4 kt · M 0.005 5 kt · M 0.008 8 kt · M 0.032 FL 200 300 kt 3 kt · M 0.007 5 kt · M 0.011 9 kt · M 0.033 FL 300 M 0.78 3 kt · M 0.010 5 kt · M 0.014 9 kt · M 0.025 FL 390 M 0.78 3 kt · M 0.010 4 kt · M 0.014 8 kt · M 0.025
Example, FL 300 at M 0.78: PFD 1 shows 287 kt, PFD 2 shows 291 kt. Difference 4 kt > 3 kt allowed → report it. ISIS Mach is not shown below M 0.50 in climb or M 0.45 in descent.
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pilots often notice small differences between the two PFD speeds and wonder whether it is a defect. This table gives the limits used to decide whether maintenance is due. Between ADR one and ADR two the limit is tight, three to four knots in flight and six on the ground. Comparing ADR three with one or two allows four or five knots, and the standby instrument against any ADR allows eight or nine. Let us work an example. At flight level three hundred and Mach point seven eight, the captain's PFD shows two hundred and eighty seven knots and the first officer's two hundred and ninety one. The difference is four knots, more than the three knots allowed, so write it up in the technical log.
Unreliable speed
The backup speed scale (BUSS) For flying when airspeed indications are unreliable Speed from angle of attack and the slat/flap configuration ; altitude from GPS ; no V/S On some aircraft: BKUP SPD/ALT pb beside each PFD, reversible , each side on its own Memo BKUP SPD/ALT ; alerts if used with the AP/FD on that side, or on both sides On other aircraft: shown on both PFDs when all ADRs are switched off , not reversible FAST SLOW red FAST: structural margin shrinking amber FAST: too fast, margin kept yellow line: current speed green triangle: target speed amber SLOW: too slow, margin kept red SLOW: stall margin shrinking 112 – – GPS ALT Speed from AOA and slat/flap configuration · altitude from GPS · no V/S
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
When all your airspeed indications are unreliable, for example with blocked pitot probes, the backup speed scale, or BUSS, gives you something to fly. It replaces the normal speed tape, and its information comes from the angle of attack, adjusted for the slat and flap configuration. Read it like a traffic light: stay in the green band, aiming for the green target triangle, while the yellow line shows where you are. Amber means too fast or too slow with margin, red means the margin is going. Altitude comes from GPS instead of the barometric scale, with the last two digits dashed, and vertical speed is not shown. How you get it depends on the aircraft: either a reversible BKUP SPD ALT button beside each PFD, or by switching off all three ADRs, which cannot be undone.
GPS
GPS and the hybrid GPIRS position Two independent receivers : a GPSSU, or inside each MMR Each ADIRU blends GPS and inertial data: GPIRS hybrid position , used by the FMGCs Normal: GPS 1 → ADIRU 1 and 3 , GPS 2 → ADIRU 2 One receiver fails: all ADIRUs use the other ADIRU 2 fails: set ATT HDG to F/O 3 ; ADIRU 3 then takes GPS 2 (side segregation) 24 satellites broadcast navigation data GPS 1 GPSSU or MMR 1 GPS 2 GPSSU or MMR 2 ADIRU 1 GPIRS hybrid ADIRU 3 GPIRS hybrid ADIRU 2 GPIRS hybrid GPS 1 → ADIRU 1 and 3 GPS 2 → ADIRU 2 FMGC 1 FMGC 2 The FMGCs use the hybrid GPIRS position GPS data on the MCDU GPS MONITOR page
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The GPS is a satellite navigation aid; twenty four satellites broadcast data that let the aircraft fix its position precisely. The A320 has two independent receivers, either in separate GPS sensor units or built into the multi-mode receivers. The receivers pass their data to the ADIRUs, and each ADIRU blends it with its own inertial position. The result is the hybrid GPIRS position, and that is what the FMGCs use. Normally GPS one supplies ADIRU one and ADIRU three, and GPS two supplies ADIRU two. If one receiver fails, all ADIRUs use the other. If ADIRU one fails, three takes GPS one. If ADIRU two fails, set ATT HDG to F O three; ADIRU three then takes GPS two, keeping side one and side two separate.
Standby instruments
The ISIS and the standby compass ISIS : attitude, speed and Mach, altitude, baro setting, LS deviations and bugs on one screenOwn gyros and accelerometers ; pressures from the standby pitot and static probes Powered by the DC ESS BUS and HOT BUS 1 Brightness: automatic photocell, then + / – ; reset with ATT RST after 350 h continuous power Compass on the windshield centre post: an APU start can disturb it10 10 200 220 240 260 280 300 320 90 95 100 105 110 10000 1013 hPa BUGS LS + – ATT RST BARO DC ESS BUS HOT BUS 1 ILS 1 / MMR 1 ADIRU 1 and 3 Standby pitot · standby static own gyros + accelerometers Inputs to the ISIS 33 N 3 6 deviation card Standby compass On top of the windshield centre post, deviation card above it. An APU start can disturb the reading (the APU power-on contactor is in the cockpit).
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the main displays are lost, the integrated standby instrument system, the ISIS, is your last line. On one small screen it shows attitude, airspeed and Mach, altitude, the barometric setting, landing system deviations and bugs. It has its own gyrometers and accelerometers, and takes its pressures straight from the standby pitot and static probes, so it does not depend on any ADIRU for its basic data. It is powered from the DC essential bus and the hot bus one. Its brightness sets itself after power-up using a light sensor, and you can adjust it with plus and minus. After three hundred and fifty hours of continuous power it must be reset with ATT RST. And on top of the windshield centre post is the standby compass, with its deviation card above it; an APU start can disturb its reading.
ISIS display
Reading the ISIS Speed: 5–250 kt in 5 kt steps, 250–520 kt in 10 kt; Mach green above 0.5 , removed below 0.45 Altitude: −2 000 to 50 000 ft ; baro in cyan , push the knob for STD Pitch marks every 2.5° to ±30°; red chevrons beyond 30° ATT RST : hold 2 s , wings level; about 10 s with "ATT 10s" shownLS pb shows deviations: not for an opposite-runway LOC take-off or a back course10 10 200 220 240 260 280 300 320 90 95 100 105 110 10000 .78 1013 hPa BUGS LS + – ATT RST BARO 1 2 3 4 5 6 1 Speed scale and Mach 2 Altitude scale 3 Roll scale, pitch marks 4 Mach (above 0.5) 5 Baro reference (cyan) 6 ATT RST button
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us read the ISIS. The speed scale runs from five to two hundred and fifty knots in five knot steps, then up to five hundred and twenty in ten knot steps, against a fixed yellow pointer. The Mach number appears in green above point five and disappears only below point four five. The altitude scale runs from minus two thousand to fifty thousand feet, and the baro setting is in cyan; push the knob for standard. Pitch is marked every two and a half degrees, and beyond thirty degrees big red chevrons point the way back. To reset the attitude, keep the wings level and hold ATT RST for at least two seconds; the reset takes about ten seconds. The LS button adds localiser and glideslope deviations, but never use them for a back course or an opposite-runway localiser.
ISIS flags
ISIS flags and the bugs function Flag Colour Meaning ATT · SPD · M · ALT red that data is lost LOC · G/S red localiser or glideslope lost WAIT ATT yellow attitude lost; back within 10 s, or replaced by ATT : RST ATT : RST yellow motion during alignment, 350 h of power, or WAIT ATT over 10 s: press ATT RST ATT 10s yellow reset in progress (countdown) MAINT · OUT OF ORDER white maintenance due (ground, below 60 kt) · internal failure with a code
BUGS: 4 speed bugs (not below 30 kt) and 2 altitude bugs. Not recommended: if both PFDs are lost later, take-off bugs could still be set on the approach.
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ISIS tells you clearly when something is wrong. Red flags mean data is lost: ATT for attitude, SPD for speed, M for Mach, ALT for altitude, and LOC and G S for the landing system. The yellow ones are about the attitude reset. WAIT ATT means attitude has been lost; if it comes back within ten seconds you carry on, otherwise it becomes ATT RST, which also appears after excessive movement during alignment or after three hundred and fifty hours of continuous power. Press the ATT RST button and ATT ten seconds counts down while it resets. White MAINT shows only on the ground below sixty knots, and OUT OF ORDER means an internal failure. The bugs function is available, but not recommended: take-off bugs left set would still be there on the approach.
Radio navigation
Three ways to tune the navaids Automatic : each FMGC tunes its own receivers; one FMGC fails → the other tunes both sidesManual : crew selects a navaid on the MCDU, for display; sent to both FMGCs; auto function not affectedBack-up : both FMGCs failed → the RMPs tuneRMP 1: VOR 1, ADF 1 ; RMP 2: VOR 2, ADF 2 ILS/GLS/MLS from either RMP, with STBY NAV on RMP 1 and RMP 2 ; RMP 3 never tunes navaids FMGC 1 FMGC 2 RMP 1 RMP 2 VOR 1 VOR 2 DME 1 DME 2 ILS 1 ILS 2 ADF 1 ADF 2 normal: FMGC tunes back-up: RMP tunes
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three ways to tune the radio navigation receivers. Automatic tuning is the normal way: each FMGC tunes its own side's receivers, choosing the best navaids for the route. If one FMGC fails, the other one tunes both sides. Manual tuning is when you type a navaid into the MCDU because you want to see it on your display; the entry goes to both FMGCs, and it does not stop them from doing their own automatic tuning for position. Back-up tuning is for when both FMGCs have failed. Then the radio management panels on the pedestal take over. The captain's RMP tunes VOR one and ADF one, the first officer's tunes VOR two and ADF two, and either one can tune the ILS, provided both are in standby navigation mode. RMP three never tunes navaids.
Radio management panel
The RMP in NAV back-up mode ACTIVE STBY/CRS 109.90 CRS 263 VHF1 VHF2 VHF3 LOAD HF1 SEL HF2 AM STBY NAV NAV VOR ILS GLS MLS ADF BFO ON OFF 1 2 3 4 5 6 7 1 ON/OFF switch 2 NAV key (guarded): back-up mode 3 STBY NAV keys 4 Tuning knobs: outer = big digits, inner = small digits or course 5 Transfer key 6 STBY/CRS window 7 ACTIVE window Both RMPs to NAV if both FMGCs or both MCDUs fail · emergency electrical configuration: only RMP 1 powered · one RMP in NAV removes navaid tuning from both FMGCs
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the radio management panel set up for back-up navigation. Lift the transparent guard and press NAV: the green light comes on and this RMP takes control of the VOR, ILS and ADF receivers away from the FMGC. Press it again to give control back. Now press a STBY NAV key, here ILS, and the active window shows what that receiver is tuned to. Set the frequency in the standby window with the knobs, the outer one for the big digits and the inner for the small ones or the course, then press the transfer key. Three traps. You must select NAV on both RMP one and RMP two. In the emergency electrical configuration, only RMP one has power. And if you tune an ILS this way, the PFDs do not show its DME distance.
Receivers
The navaid receivers and where they show Receiver Fit Displayed on VOR 2 NDs (EFIS ADF/VOR selectors); DDRMI bearings if heading valid ILS / GLS / MLS 2 (in the MMRs if fitted) ILS 1 → PFD 1 and ND 2 · ILS 2 → PFD 2 and ND 1 ; PFD with LS pb, ND in ROSE LSDME 2 auto-paired with the VOR or ILS frequency; with a VOR on the ND and DDRMI, with an ILS on the PFD ADF 1 or 2 NDs (ADF/VOR selectors), DDRMI Marker beacon 1, inside VOR 1 outer, middle and inner markers on the PFD
The cross-over is deliberate: each pilot sees one ILS on the PFD and the other on the ND, so the two receivers can be compared.
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the receivers. Two VORs, shown on the navigation displays according to the ADF VOR selectors on the EFIS control panel, and on the DDRMI if the heading signal is valid. Two ILS receivers, which on aircraft with multi-mode receivers also handle GLS and MLS. Now the classic question: the captain's PFD shows ILS one, but the captain's ND shows ILS two, and the reverse on the first officer's side. That cross-over lets each pilot compare both receivers. The two DMEs are paired automatically with the VOR or ILS frequency. There may be one or two ADFs. And there is a single marker beacon receiver, built into VOR one, which puts the outer, middle and inner markers on the PFD.
DDRMI
The digital distance and radio magnetic indicator Compass card from ADIRU 1 (ADIRU 3 when switched) Dashed pointer: VOR 1 or ADF 1; double pointer: VOR 2 or ADF 2DME counters: whole NM above 20 NM , tenths below 20 NM, 0 below 1 NM Flags for a failed receiver, DDRMI fault, invalid ADIRS heading or power loss Pointers may oscillate beyond about 25 NM on some receivers 0 3 6 9 12 15 18 21 24 27 30 33 25 12.4 DME 1 DME 2 VOR ADF VOR ADF dashed pointer: VOR 1 / ADF 1 · double pointer: VOR 2 / ADF 2
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The DDRMI is a small standby instrument for radio navigation. Its compass card is driven by ADIRU one, or by ADIRU three when the ATT HDG selector is switched. The dashed pointer shows the bearing to VOR one or ADF one, and the double pointer VOR two or ADF two, chosen with the small selectors. At the top, the two DME counters show the distance. Above twenty nautical miles they show whole miles, so twenty five point three reads twenty five. Below twenty they show tenths, so twelve point three seven reads twelve point four. Below one mile they show zero. Flags appear if a receiver fails, if the DDRMI fails, if the heading from the ADIRS is invalid or if power is lost.
Radio altimeter
Two radio altimeters Two radio altimeters, RA 1 and RA 2Captain PFD shows RA 1 , first officer PFD shows RA 2 One RA fails: both PFDs show the remaining one Radio height is the height above the ground directly below Both RAs failed: TCAS STBY memo (see Surveillance) RA 1 RA 2 CAPT PFD: RA 1 480 F/O PFD: RA 2 one fails → both show the other Two radio altimeters measure the height above the ground
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 has two radio altimeters. Each sends a radio signal straight down and measures the time it takes to come back from the ground, giving the true height above whatever lies below, whether it is a runway, a hill or the sea. Radio altimeter one feeds the captain's PFD and radio altimeter two feeds the first officer's. If one fails, both PFDs show the height from the remaining one, so you lose the cross-check but not the information. Radio height also drives the automatic callouts we look at next, the ground proximity warning system and the TCAS. In fact, if both radio altimeters fail, the TCAS STBY memo appears, as we will see in the surveillance lesson.
Automatic callouts
Radio height callouts 2500 ft 1000 ft 500 ft 100 ft 50 ft 10 ft 5 ft TWENTY FIVE HUNDRED TWO THOUSAND ONE THOUSAND FIVE HUNDRED FOUR HUNDRED THREE HUNDRED TWO HUNDRED ONE HUNDRED FIFTY FORTY THIRTY TWENTY TEN FIVE RETARD RETARD at 20 ft (10 ft with A/THR active and an AP in LAND) HUNDRED ABOVE at DH + 100 · MINIMUM at DH DH: radio height · MDA/MDH: barometric FWC synthetic voice below 2 500 ft, through the loudspeakers even if they are off Intermediate callouts: if more than 11 s pass between callouts (4 s below 50 ft), the height is repeated every 4 s · operators choose which callouts are active
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Below two thousand five hundred feet, the flight warning computer announces the radio height in a synthetic voice through the cockpit loudspeakers, even if the speakers are switched off. The full list runs twenty five hundred, two thousand, one thousand, five hundred, four, three, two hundred, one hundred, fifty, forty, thirty, twenty, ten and five; each operator selects which ones are active. With a decision height set, you hear HUNDRED ABOVE and then MINIMUM; for non-precision approaches the reference is the barometric minimum. If more than eleven seconds pass without a callout, or four seconds below fifty feet, the present height is repeated every four seconds. And RETARD comes at twenty feet, or at ten feet when the autothrust is active and an autopilot is in LAND mode.
Summary
Navigation in one page ADIRS 3 ADIRUs (ADR + IR). ADIRU 1 CAPT probes, 2 F/O, 3 STBY + CAPT TAT. 8 ADMs.
Panel OFF kills ADR and IR. ATT: attitude + heading only. NAV lost for the flight if moved in flight. FAULT flashing: try ATT.
Alignment IRS IN ALIGN X MN: green, amber with an engine running. ON BAT: ADIRU on batteries.
Switching ATT HDG / AIR DATA: CAPT 3 or F/O 3. ADIRU 2 failed: F/O 3 also keeps GPS segregation.
Backups BUSS: AOA speed + GPS altitude. ISIS: own sensors, STBY pitot/static, ATT RST. Compass: APU start.
Radios FMGC tunes; MCDU manual; RMP back-up (NAV on both). ILS 1 → PFD 1 + ND 2.
DDRMI Dashed = 1, double = 2. DME tenths below 20 NM.
RA RA 1 → CAPT, RA 2 → F/O. Callouts below 2 500 ft. RETARD at 20 ft (10 ft autoland).
Chapter 25 · Navigation: ADIRS, Standby Instruments and Radio Navigation
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. Three ADIRUs, each an ADR and an IR, with ADIRU one on the captain's probes, two on the first officer's, and three on the standby probes plus the captain's TAT. On the panel, OFF kills the whole unit, ATT gives attitude and heading only, and NAV is lost for the flight if you move the selector in the air. A flashing FAULT means try ATT. Alignment shows as IRS IN ALIGN, amber once an engine runs. Switching brings ADIRU three to either side. The BUSS uses angle of attack and GPS altitude, and the ISIS has its own sensors. The FMGCs tune the radios, with the RMPs as back-up. ILS one goes to PFD one and ND two. And RETARD comes at twenty feet, or ten in autoland.