Air Law · Chapter 11
Altimeter Setting Procedures One instrument, three settings: what QNH, QFE and 1013 tell you, and exactly when to change from one to another.
0 1 2 3 4 5 6 7 8 9 4 000 1013 © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter eleven is about the altimeter and the number you set in its little window. Set the wrong one and the altimeter can mislead you by hundreds of feet, which is why so many accidents began with a wrong setting. We look at the three settings, QNH, QFE and the standard 1013, at the transition altitude, layer and level, and at what to set in each phase of flight.
Objectives
Two jobs for one instrument Near the ground the job is terrain clearance : charts give heights above sea level , so use the local QNH Higher up the job is separation : everyone sets the same 1013 hPa , so 1000 ft on one altimeter means 1000 ft on all A flight level is height above the 1013 hPa pressure level, in steps of 500 ft; the lowest usable one is at or just above the minimum flight altitude The pilot stays responsible, whatever ATC does Terrain
Low down Obstacles and procedure altitudes on charts are all above mean sea level . With local QNH set, your altimeter speaks the same language as the chart.
1000 ft everyone on 1013: same error for all Traffic
High up Pressure changes from place to place. If everyone sets 1013 , the errors are the same for all, so vertical separation still works.
Chapter 11 · Altimeter Setting Procedures
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
The altimeter setting has two jobs. Near the ground, the job is to avoid terrain. Every obstacle and every altitude on an approach or departure chart is measured above mean sea level, and sea level pressure changes from place to place, so you set the local QNH and your altimeter then shows height above sea level, just like the chart. Higher up, the job is to keep aircraft apart. Here everyone sets the same standard pressure, one zero one three hectopascals, so that one thousand feet on one altimeter means the same as on any other, even though the true height may differ. A flight level is the height above the one zero one three point two hectopascal pressure level, in steps of five hundred feet. The lowest usable flight level is the one at, or just above, the minimum flight altitude. And whatever ATC tells you, the pilot remains responsible for setting the altimeter correctly.
Three settings, three answers
The same aircraft, the same moment sea level 600 ft0 1 2 3 4 5 6 7 8 9 0 QFE QFE reads 0: height above the field0 1 2 3 4 5 6 7 8 9 600 QNH QNH reads 600: altitude above sea level0 1 2 3 4 5 6 7 8 9 900 1013 Standard 1013 reads pressure altitudeQFE Pressure at the aerodrome . On the ground the altimeter reads zero : height above the field. Fine for flying the circuit.
QNH Aerodrome pressure reduced to sea level using ISA. On the ground it reads the aerodrome elevation : altitude.
1013 and QNE Standard pressure setting : reads pressure altitude, used for flight levels. QNE is what it reads on landing with 1013 set.
Chapter 11 · Altimeter Setting Procedures
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is one aircraft on a runway six hundred feet above sea level, with three settings. With QFE set, the pressure at the aerodrome, the altimeter reads zero on the ground and shows height above the field; that suits a pilot staying in the circuit. With QNH set, the aerodrome pressure reduced to sea level using the standard atmosphere, it reads six hundred, the aerodrome elevation, and shows altitude above sea level. With the standard setting of one zero one three, it reads pressure altitude, which is what flight levels use; on a low-pressure day it might read nine hundred here. QNE is not the same as one zero one three: it is what the altimeter reads on landing with one zero one three set, used in the rare case where the QNH is too low for the altimeter’s scale.
01
Transition Where you change the setting, climbing and descending.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: transition, where you change the setting on the way up and on the way down.
Transition altitude, layer and level
Up on 1013, down on QNH Transition altitude climbing: set 1013, use flight levels Transition level descending: set QNH, use altitudes transition layer en route: flight levels on 1013Transition altitude Set by the state for each aerodrome, published in the AIP; as low as possible but normally at least 3000 ft , rounded up to the next 1000 ft. In India the lowest is 4000 ft .
Transition level The first usable flight level above the transition altitude. Set by ATC, it changes with QNH and is given in approach clearances.
Transition layer The airspace between them. Climbing through it, report flight levels ; descending through it, report altitudes .
Chapter 11 · Altimeter Setting Procedures
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The change from one setting to another happens at the transition. The transition altitude is set by the state for each aerodrome and published in the AIP and on the charts. It should be as low as possible, but normally at least three thousand feet above the aerodrome, rounded up to the next thousand feet; in India the lowest transition altitude is four thousand feet. Climbing, you set one zero one three as you pass the transition altitude, and from then on you use flight levels. The transition level is the first usable flight level above the transition altitude. ATC works it out, it changes as the QNH changes, and it is passed in approach clearances. Descending, you set the QNH as you pass the transition level, and from then on you use altitudes. The airspace between the two is the transition layer. Climbing through it you report flight levels; descending through it you report altitudes.
Phases of flight
What to set in each phase QNH 600 reads elevation QNH comes with the taxi clearance Before take-off QNH comes in the taxi clearance . Check the altimeter against the known elevation.
Climb QNH until the transition altitude , then 1013.
TA flight levels on 1013 altitudes on a nearby QNH En route Below the transition altitude: altitude on a nearby QNH. Above it: flight levels on 1013.
TL set QNH 1013 latest QNH before going below TL Approach Get the transition level before the approach and the latest QNH before descending below it. After an approach clearance, ATC may let you use QNH earlier for a continuous descent.
QFE 0 2000 (1485): AMSL (above the field) Circuit only Staying in the visual circuit, you may use QFE . Charts show both: 2000 (1485) means 2000 ft AMSL, 1485 ft above the field.
QNH 600 QFE 0 at least one on QNH Two altimeters At least one must be set to QNH when required.
Chapter 11 · Altimeter Setting Procedures
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
What should be set in each phase? Before take-off, the QNH comes with the taxi clearance, and you check the altimeter against the known elevation. In the climb, use QNH until the transition altitude, then one zero one three. En route below the transition altitude, fly altitudes on the QNH of a nearby aerodrome; above it, fly flight levels on one zero one three. Before the approach, get the transition level, and before descending below it, the latest aerodrome QNH. Once you are cleared for an approach, ATC may let you set QNH above the transition level so that a jet can descend without interruption. If you are staying in the visual circuit, you may use QFE. Approach charts show both: two thousand with fourteen eighty-five in brackets means two thousand feet above sea level and one thousand four hundred and eighty-five above the aerodrome. And with two altimeters, at least one must be on QNH.
Pre-flight check
Is the altimeter telling the truth? Park where the elevation is known and set QNH (or QFE) Vibrate the instrument, by tapping or with the built-in vibrator It should read the elevation (or zero) within ±60 ft (20 m) for instruments tested to 30 000 ft Within ±80 ft (25 m) for instruments tested to 50 000 ft Outside the tolerance: the altimeter is not serviceable indicated true: lower! very cold Watch out
A cold-day warning In very cold air the true altitude is lower than indicated. Near terrain, low temperature corrections matter.
QFE 0 ±60 ft tested to 30 000 ft ±80 ft tested to 50 000 ft tap it, then read: outside = unserviceable Exam
Remember the numbers 60 ft for a 30 000 ft instrument, 80 ft for a 50 000 ft instrument.
Chapter 11 · Altimeter Setting Procedures
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before flight, check the altimeter. Park at a spot whose elevation you know, set the QNH, or the QFE, and vibrate the instrument by tapping it or with its built-in vibrator. It should read the elevation, or zero with QFE, within plus or minus sixty feet, twenty metres, for an altimeter tested up to thirty thousand feet, and within plus or minus eighty feet, twenty-five metres, for one tested up to fifty thousand feet. If not, it is not serviceable. And remember that in very cold air your true altitude is lower than the altimeter shows, which matters near terrain.
Summary
What to take into the exam QFE Reads zero on the aerodrome: height.
QNH Reads aerodrome elevation: altitude. Used near the ground and below the TA.
1013 Standard pressure setting: flight levels. QNE = reading on landing with 1013.
TA set by the state ≥ 3000 ft · India 4000 climb: 1013 Transition altitude By the state; at least 3000 ft normally; India lowest 4000 ft. Climbing: set 1013.
Transition level First usable FL above TA; by ATC; descending: set QNH. Layer between them.
QFE 0 ±60 ft ±80 ft 30k / 50k instrument Accuracy ±60 ft (0–30 000 ft instrument), ±80 ft (0–50 000 ft).
Chapter 11 · Altimeter Setting Procedures
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six things to take into the exam. QFE reads zero on the aerodrome, so it shows height. QNH reads the aerodrome elevation, so it shows altitude; use it near the ground and below the transition altitude. One zero one three is the standard setting for flight levels, and QNE is what you read on landing with it set. The transition altitude is set by the state, normally at least three thousand feet, and in India no lower than four thousand; climbing, set one zero one three there. The transition level is the first usable flight level above it, set by ATC; descending, set QNH there; the layer lies between them. And the altimeter check tolerance is sixty feet for a thirty thousand foot instrument and eighty feet for a fifty thousand foot one.