Air Law · Chapter 9
Approach and Circling Procedures From the airway down to the runway on instruments: segments, minima, gradients, turning procedures, the missed approach and circling.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter nine brings the aircraft back down. An instrument approach takes you from the airway to a point where you can see the runway, or to a missed approach if you cannot. We look at the five segments of an approach, precision and non-precision approaches, how minima are built, descent gradients, the procedures for turning round, the missed approach, and circling to land on another runway.
Chapter roadmap
What this chapter covers 01
Building blocks Speed categories, MSA, precision and non-precision, the five segments.
02
Minima and gradients OCA/H, DA/H and MDA/H, ILS categories, descent gradients.
03
Manoeuvres Reversal and racetrack procedures, the missed approach, circling.
Chapter 9 · Approach and Circling Procedures
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three parts. First, the building blocks: aircraft categories, the minimum sector altitude, precision and non-precision approaches, and the five segments. Second, minima and gradients: obstacle clearance height, decision height and minimum descent height, the ILS categories and descent gradients. Third, the manoeuvres: reversal and racetrack procedures, the missed approach, and circling.
Categories
Categories by threshold speed Cat Vat (kt) Initial approach (kt) Final approach (kt) Max circling (kt) A below 91 90–150 (110*) 70–100 100 B 91–120 120–180 (140*) 85–130 135 C 121–140 160–240 115–160 180 D 141–165 185–250 130–185 205 E 166–210 185–250 155–230 240
Cat A below 91 kt Cat B 91 kt Cat C 121 kt Cat D 141 kt Cat E 166 kt 210 kt Vat = 1.3 × stall speed in landing configuration, at maximum landing mass Vat 1.3 × stall speed in the landing configuration (or 1.23 × the 1 g stall speed) at maximum certificated landing mass. * = maximum for reversal or racetrack procedures.
Chapter 9 · Approach and Circling Procedures
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Approach procedures are designed around speed, so aircraft are sorted into categories by Vat, their speed over the threshold, which is one point three times the stalling speed in landing configuration at maximum landing mass. Category A is below ninety-one knots; B from ninety-one to one hundred and twenty; C from one hundred and twenty-one to one hundred and forty; D from one hundred and forty-one to one hundred and sixty-five; and E from one hundred and sixty-six to two hundred and ten. Each category has its own speed ranges for the initial and final approach and a maximum speed for circling: one hundred knots for A, one hundred and thirty-five for B, one hundred and eighty for C, two hundred and five for D and two hundred and forty for E. The starred figures are the maximum speeds for reversal and racetrack procedures.
Basics
Safe altitudes and two kinds of approach 1000 ft within 25 NM of the aid MSA At least 300 m (1000 ft) clearance within 25 NM of the aid or fix. You may go below it only when you can see the ground, are radar vectored, or are flying the published procedure.
Precision Guidance in direction and height (ILS, MLS, PAR, GLS) down to a decision altitude/height .
Non-precision Guidance in direction only (VOR, NDB, localiser alone, surveillance radar) down to a minimum descent altitude/height .
IAF fly it as published break off after IAF: missed approach Finishing it Once you start a procedure, complete it as published unless ATC says otherwise; if you break off after the IAF, fly the missed approach .
outer marker RVR too low: do not continue non-precision: not below 1000 ft Approach ban Do not continue past the outer marker (precision) or below 1000 ft (non-precision) if the reported RVR or visibility is below minimum.
DA/H past the marker: carry on After that point If RVR drops below minimum after it, you may continue to DA/H or MDA/H , and land if you see what you need.
Chapter 9 · Approach and Circling Procedures
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before the approach begins, you are protected by the minimum sector altitude, which gives at least three hundred metres, one thousand feet, of clearance within twenty-five nautical miles of the aid or fix. You may descend below it only when you can see the aerodrome and terrain and will continue to, when you are being radar vectored, or when you are flying the published procedure. There are two broad kinds of approach. A precision approach gives guidance in both direction and height, from an ILS, MLS, precision radar or a GPS landing system, down to a decision altitude or height. A non-precision approach gives direction only, from a VOR, an NDB, a localiser on its own or surveillance radar, down to a minimum descent altitude or height. Once a procedure is started, complete it as published unless ATC says otherwise, and if you abandon it after the initial approach fix, fly the missed approach. One rule protects you from starting hopeless approaches: do not continue past the outer marker on a precision approach, or below one thousand feet on a non-precision one, if the reported visibility or RVR is below the minimum. If it drops below minimum after that point, you may continue to the decision or minimum descent height, and land if you then have the visual reference you need.
01
The five segments Each one starts and ends at a fix.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part one: the five segments of an approach, each starting and ending at a fix.
The five segments
Arrival, initial, intermediate, final, missed approach Arrival IAF Initial MOC 300 m IF Intermediate 300 → 150 m FAF Final MAPt Missed approachInitial IAF to IF, 300 m (984 ft) MOC. Intercept the next track at up to 90° (precision) or 120° (non-precision); a DR leg at most 45° and 10 NM .
Intermediate IF to FAF: slow down and configure; descent kept shallow. MOC 300 m falling to 150 m .
Final Non-precision with FAF: FAF to MAPt, FAF best at 5 NM , at most 10 NM . Precision: from the FAP , where the glide path is met, 1000–3000 ft up.
Chapter 9 · Approach and Circling Procedures
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
An instrument approach has five segments, each starting and ending at a fix. The arrival takes you from the airway to the initial approach fix; if the route is twenty-five nautical miles or longer, a standard arrival route, a STAR, is published. The initial segment runs from the initial approach fix to the intermediate fix, with three hundred metres, nine hundred and eighty-four feet, of obstacle clearance. It may join the next track at up to ninety degrees for a precision approach or one hundred and twenty for a non-precision one; a dead-reckoning leg may meet it at no more than forty-five degrees and be no longer than ten nautical miles. The intermediate segment, from the intermediate fix to the final approach fix, is where you slow down and configure, so descent is kept shallow; clearance reduces from three hundred to one hundred and fifty metres. The final segment is where you line up and descend. On a non-precision approach with a final approach fix, it runs from that fix, best placed five nautical miles from the threshold and no more than ten, to the missed approach point. On a precision approach it starts at the final approach point, where the intermediate altitude meets the glide path, normally between one thousand and three thousand feet up. And the fifth segment is the missed approach.
Precision and non-precision
The difference is height guidance Precision direction and height (ILS, MLS, PAR, GLS) down to DA/H Non-precision direction only (VOR, NDB, localiser alone) level at MDA/HStraight-in Each segment lined up with the runway where possible. A non-precision final may meet the runway line at up to 30° .
No FAF One beacon is both IAF and MAPt: descend once established inbound ; the track is rarely on the runway line.
Step-down fix Gives two OCA/H values: the lower one only if you positively identify the fix.
Chapter 9 · Approach and Circling Procedures
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The real difference between the two kinds of approach is height guidance. On a precision approach, the localiser gives direction and the glide path gives height, and if you keep within half-scale deflection you stay inside protected airspace all the way down to the decision height. On a non-precision approach you have direction only; you descend to the minimum descent altitude and fly level there until you see the runway or reach the missed approach point. Wherever possible each segment is lined up with the runway, but a non-precision final may meet the runway centre line at up to thirty degrees. At some aerodromes a single beacon serves as both the initial approach fix and the missed approach point, with no final approach fix; then you start the final descent once established inbound, and the track rarely lines up with the runway. And a step-down fix gives two obstacle clearance heights: the lower one applies only if you positively identify the fix.
02
Minima and gradients How low you may go, and how steeply.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part two: minima and gradients, how low you may go and how steeply.
Minima
How the lowest heights are built OCA/H : the lowest altitude or height that keeps the procedure’s obstacle clearance; set by the state , published, and depends on the categoryPrecision: measured from the threshold . Non-precision: from the aerodrome, or the threshold if it is more than 2 m (7 ft) lower. Circling: from the aerodrome DA/H (precision) or MDA/H (non-precision) = OCA/H plus what the operator adds, never below the system minimum : CAT I 200 ft , CAT II 100 ft Operating minima are the operator’s job, so ICAO charts do not show them Controlling obstacle OCA/H: set by the state, on the chart DA/H = OCA/H + what the operator adds System minimum wins if higher: CAT I 200 ft, CAT II 100 ft
Chapter 9 · Approach and Circling Procedures
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The lowest heights on an approach are built up in layers. The obstacle clearance altitude or height is set by the state from its survey: the height of the controlling obstacle plus a clearance margin. It depends on the aircraft category and is published on the chart. For a precision approach it is measured from the threshold. For a non-precision approach it is measured from the aerodrome elevation, or from the threshold if that is more than two metres, seven feet, lower. For circling it is measured from the aerodrome elevation. The operator then adds its own margin to get the decision altitude or height for a precision approach, or the minimum descent altitude or height for a non-precision one. That figure can never be below the system minimum, two hundred feet for a category one ILS and one hundred feet for category two. Because operating minima are the operator’s responsibility, ICAO charts do not show them.
ILS categories
Lower minima need better systems CAT I DH ≥ 200 ft RVR ≥ 550 m CAT II DH 100–200 ft RVR ≥ 350 m CAT IIIA DH < 100 ft RVR ≥ 200 m CAT IIIB DH < 50 ft RVR 50–200 m CAT IIIC no DH no RVR limitCAT I Flown with the pressure altimeter . RVR at least 550 m, or ground visibility 800 m.
CAT II Flown with a radio altimeter and flight director. Glide path must be 3° for CAT II and III.
Glide path Between 2.5° and 3.5° ; a steeper path only when nothing else clears the obstacles. Missed approach climb 2.5% .
Chapter 9 · Approach and Circling Procedures
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ILS categories show how low you may go. Category one: a decision height of at least two hundred feet, with an RVR of at least five hundred and fifty metres or a ground visibility of eight hundred metres, flown with the pressure altimeter. Category two: a decision height below two hundred but not below one hundred feet, and an RVR of at least three hundred and fifty metres, flown with a radio altimeter and flight director. Category three A: below one hundred feet or no decision height, with an RVR of at least two hundred metres. Category three B: below fifty feet or none, with an RVR between fifty and two hundred metres. And category three C: no decision height and no RVR limit. The glide path is normally between two and a half and three and a half degrees, and must be three degrees for categories two and three. The missed approach is designed for a two and a half percent climb.
Descent
How steeply the final approach goes down Optimum final descent: 5.2% , a 3° path, about 318 ft per NM Steepest normally: 6.5% for categories A and B, 6.1% for C, D and E; helicopters 10% Steeper paths need state approval, an approved operator, approved aircraft and trained pilots The intermediate segment is kept as flat as possible CDFA : one continuous descent with no level-offs, to about 50 ft over the threshold, staying above every step-down fix 1 NM · 320 ft 2 NM · 640 ft 3 NM · 950 ft 4 NM · 1270 ft 5 NM · 1590 ft 6.5% max 3° ≈ 5.2% ≈ 318 ft per NM steepest normally: 6.5% (cat A, B) · 6.1% (cat C, D, E)
Chapter 9 · Approach and Circling Procedures
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
How steeply does the final approach go down? The best gradient is five point two percent, which is a three-degree path, about three hundred and eighteen feet per nautical mile. Some older manuals round this to five percent and three hundred feet per mile, and that rounding still works for quick sums. Where a steeper path is needed, the normal maximum is six point five percent for categories A and B and six point one percent for C, D and E, and ten percent for helicopters. Anything steeper needs the state’s approval, an approved operator, specially approved aircraft and trained pilots. The intermediate segment is kept as flat as possible, so you can slow down. And on a non-precision approach the preferred technique is the continuous descent final approach: one steady descent with no level-offs, to about fifty feet over the threshold, passing at or above every step-down fix.
03
Manoeuvres Turning round, going around, and circling.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Part three: the manoeuvres, turning round, going around, and circling.
Reversal and racetrack procedures
When there is no straight-in route 45°/180° turn 45° off, timed leg, 180° back 80°/260° turn 80° one way, 260° the other Base turn outbound at an angle, turn in Racetrack 1–3 min legs, like a hold45°/180° Turn 45° off the outbound track, fly a timed leg (1 min for A and B, 1 min 15 s for C, D, E), then turn 180° to meet the inbound track at 45°.
80°/260° and base turn 80° one way then 260° the other, about 2 minutes in still air. A base turn flies out at an angle and turns straight onto the inbound track.
Racetrack Turn 180° over the fix, outbound 1, 2 or 3 minutes or to a DME distance, then 180° back. Used when the entry sector rules out the others.
Chapter 9 · Approach and Circling Procedures
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
When there is no remote fix to start a straight-in approach, the aircraft flies out from the beacon and turns round to come back. There are four ways. The forty-five, one eighty procedure turn: turn forty-five degrees off the outbound track, fly a timed leg of one minute for categories A and B or one minute fifteen seconds for C, D and E, then turn through one hundred and eighty degrees to meet the inbound track at forty-five degrees. The eighty, two sixty procedure turn: turn eighty degrees one way and immediately two hundred and sixty the other, taking about two minutes in still air. The base turn: fly outbound on a track at an angle to the inbound one, then turn straight onto the inbound track. And the racetrack: turn one hundred and eighty degrees over the fix, fly outbound for one, two or three minutes, or to a DME distance, then turn one hundred and eighty degrees back. It looks like a hold, and is used when the direction you arrive from does not suit the other procedures. Fly the directions and timings exactly, because the protected airspace is built around them.
The missed approach
Three phases, one rule: start at the MAPt MAPt: missed approach point Initial climb set up, no turns Intermediate 2.5% climb, 30 m MOC, turns ≤ 15° Final from 50 m MOC, turns allowedWhere it starts At the MAPt : where the glide path meets DA/H, a facility, a fix, or a set distance from the FAF.
Going early? If you decide to go around early, fly on to the MAPt first (you may be higher), then follow the procedure.
The climb Normally 2.5% , to at least the MSA or the published altitude.
Chapter 9 · Approach and Circling Procedures
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
If you do not have the visual reference you need at the decision or minimum descent height, or at any time you cannot continue, you fly the missed approach printed on the chart, together with the radio failure procedure. It starts at the missed approach point, which may be where the glide path meets the decision height, a facility, a fix, or a set distance from the final approach fix. If you decide to go around before reaching that point, carry on to it, higher if you like, and then follow the procedure, so you stay in protected airspace. There are three phases. The initial phase, from the missed approach point until the climb is set up, has no turns, because the crew is busy with power and configuration. The intermediate phase continues the climb at two and a half percent, with thirty metres of clearance and turns of no more than fifteen degrees. The final phase begins once fifty metres, one hundred and sixty-four feet, of clearance is reached and kept, and full turns may be made, back to another approach, a hold or the en-route structure.
Visual manoeuvring
Circling to land on another runway After an instrument approach, a visual manoeuvre to land on a runway not lined up for straight-in; always treated as non-precision Keep the runway environment in sight throughout, at or above the circling MDA/H Stay inside the circling area : arcs drawn round each threshold, joined by tangents; the radius depends on category, speed, a 25 kt wind and 20° bank A sector may be closed to circling Lose sight of the runway: climbing turn towards the landing runway, then fly the missed approach for the instrument runway no circling instrument approach circle, runway in sight radius R by category
Chapter 9 · Approach and Circling Procedures
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Circling, or visual manoeuvring, is the visual part of an approach that lands on a runway not lined up for a straight-in landing. Any instrument approach can be used, but the descent goes only to the circling minimum descent height, and circling is always treated as non-precision. You must keep the runway environment in sight throughout. You must also stay within the circling area, drawn by arcs around each runway threshold joined by straight lines. The radius depends on the aircraft category and speed, assuming a twenty-five knot wind and a bank of twenty degrees or rate one, whichever is less. A sector may be closed to circling where obstacles would make the minimum unreasonable. If you lose sight of the runway while circling, climb while turning towards the runway you meant to land on, and once overhead, fly the missed approach for the instrument runway you approached on, not the one you were trying to land on.
Circling table
ICAO circling figures by category Cat Obstacle clearance Lowest OCH above aerodrome Minimum visibility Max speed A 90 m (295 ft) 120 m (394 ft) 1.9 km (1.0 NM) 100 kt B 90 m (295 ft) 150 m (492 ft) 2.8 km (1.5 NM) 135 kt C 120 m (394 ft) 180 m (591 ft) 3.7 km (2.0 NM) 180 kt D 120 m (394 ft) 210 m (689 ft) 4.6 km (2.5 NM) 205 kt E 150 m (492 ft) 240 m (787 ft) 6.5 km (3.5 NM) 240 kt
A B C D E 394 ft A 492 ft B 591 ft C 689 ft D 787 ft E lowest circling OCH: about 100 ft more per category Pattern The lowest OCH rises by about 100 ft per category, from 394 ft for A to 787 ft for E.
Chapter 9 · Approach and Circling Procedures
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the ICAO circling figures. Category A: ninety metres of obstacle clearance, a lowest obstacle clearance height of one hundred and twenty metres, three hundred and ninety-four feet, a visibility of one point nine kilometres and a top speed of one hundred knots. Category B: ninety metres, one hundred and fifty metres or four hundred and ninety-two feet, two point eight kilometres, one hundred and thirty-five knots. Category C: one hundred and twenty metres, one hundred and eighty metres or five hundred and ninety-one feet, three point seven kilometres, one hundred and eighty knots. Category D: one hundred and twenty metres, two hundred and ten metres or six hundred and eighty-nine feet, four point six kilometres, two hundred and five knots. Category E: one hundred and fifty metres, two hundred and forty metres or seven hundred and eighty-seven feet, six point five kilometres, two hundred and forty knots.
Summary
What to take into the exam A B C D E by speed over the threshold Categories By Vat: A < 91, B 91–120, C 121–140, D 141–165, E 166–210 kt.
Segments and MOC Initial 300 m; intermediate 300→150 m; FAF best 5 NM, max 10. MSA 1000 ft within 25 NM.
OCA/H DA/H + operator margin CAT I 200 ft · CAT II 100 ft Minima OCA/H from the state; DA/H or MDA/H adds the operator margin. CAT I 200 ft, CAT II 100 ft.
Gradient 5.2% (3°, 318 ft/NM) best; max 6.5% (A, B) or 6.1% (C–E). Missed approach climb 2.5%.
beacon 45° 45°/180° · 1 min A/B, 1:15 C–E Reversals 45°/180° (1 min A/B, 1:15 C–E), 80°/260°, base turn, racetrack 1–3 min.
Missed approach and circling Start at the MAPt; no turns in the initial phase; 50 m in the final phase. Circling: fly the instrument runway’s missed approach.
Chapter 9 · Approach and Circling Procedures
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six things to take into the exam. Categories by threshold speed: A below ninety-one knots, B to one hundred and twenty, C to one hundred and forty, D to one hundred and sixty-five, E to two hundred and ten. Segments and clearance: three hundred metres in the initial segment, falling to one hundred and fifty in the intermediate; the final approach fix best at five nautical miles and no more than ten; the minimum sector altitude gives one thousand feet within twenty-five nautical miles. Minima: the state sets the obstacle clearance height and the operator adds its margin, never below two hundred feet for category one or one hundred for category two. Gradients: five point two percent, three degrees, is best; six point five or six point one percent is the steepest normally allowed; the missed approach climbs at two and a half percent. Reversals: the forty-five one eighty with one minute or one minute fifteen, the eighty two sixty, the base turn and the racetrack. And the missed approach starts at the missed approach point with no turns in the first phase; when circling, fly the missed approach for the instrument runway.