Aircraft Systems · Chapter 2
Wings, Stabilisers, Materials and Corrosion How wings and tail surfaces are built and controlled, why they flutter, twist and diverge, what the airframe is made of, how it corrodes, and how safe its systems must be.
spars · ribs · controls · materials
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to lesson two. In the first lesson we built the fuselage; now we move out along the wing and back to the tail. You will see how a wing carries its loads through spars, ribs and skin, why we keep fuel in the wings and hang engines under them, and how the control surfaces on the wings and tail are balanced, trimmed and given feel. We will look at the dangerous ways a flexible structure can misbehave, flutter, reversal and divergence, and then at the materials the airframe is made of, how they corrode, what a heavy landing does, and how safe the systems must be.
Roadmap
From wing root to tail cone 1 · Wings Wing types, spars, the torsion box, bending relief and engine position.
2 · Tail and controls Tail units, axes, combined surfaces, trimming, roll control at speed.
3 · Balance, tabs, flutter Hinge moments, tabs, mass balance, aeroelastic effects, powered controls and feel.
4 · Materials and safety Metals, composites, corrosion, heavy landings and failure probabilities.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. We begin with the wings: how they are braced or cantilevered, how spars, ribs, stringers and skin form a torsion box, why fuel in the wings and engines on the wings relieve bending, and what changes when the engines go on the rear fuselage. Then we move to the tail and the controls: the tail unit layouts, the three axes, combined surfaces such as flaperons and stabilators, trimming with a moving tailplane, and how a jet controls roll at high speed. The third part covers the forces on the controls themselves: hinge moments and aerodynamic balance, the family of tabs, flutter and mass balance, reversal and divergence, and powered controls with artificial feel. Finally we look at materials, corrosion, heavy landings and the probability targets for system failures.
Part 1 · Wings
Biplane, braced and cantilever wings The wing must be strong and stiff enough to carry the aircraft; thickness and type depend on the speed Biplane : spars, interplane struts and wires make a rigid lattice girder; slow, so low air loadsBraced monoplane : struts or wires carry part of the load; low-speed aircraftCantilever wing: supported at one end only , with no external bracing A cantilever wing carries lift and drag in flight and its own weight on the ground
Biplane
spars, interplane struts and
bracing wires form a rigid lattice
girder; slow, under about 200 kt
Braced monoplane
a strut or wire takes part of the
wing load to the fuselage;
low-speed aircraft
Cantilever monoplane
fixed at the root only, no external
bracing; all the loads go through
the spars
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The wing has to support the whole aircraft in the air, so it must be strong enough and stiff enough, and how that is achieved depends mainly on the speed the aircraft is built for. A biplane flies slowly, usually below two hundred knots, so the air loads are small, and its two wings, joined by interplane struts and bracing wires, form a lattice girder that is very rigid in bending and twisting. A braced monoplane has a single wing held partly by struts or wires running to the fuselage; again, it suits low speeds, because the bracing adds drag. Fast aircraft use the cantilever monoplane: the wing is supported at the root only, with no external bracing at all. That means everything goes through the internal structure: lift, drag and twisting in flight, and on the ground the wing must also hold up its own weight, bending the other way.
Part 1 · Wings
Spars and wing bending The spars are the main load-bearing members: they take bending and, with the skin, twisting loads Flanges (booms) carry tension and compression; the web carries shear In flight the upper skin is in compression , the lower skin in tension ; on the ground, the reverse In stressed-skin wings, bending is carried by both spars and skin The maximum bending moment is at the root ; wing loading = weight ÷ wing area
Typical spar sections
I-section
channel
top hat
box
flanges (booms, blue) carry bending as tension and compression; the web carries shear
In flight the wing bends upward
upper skin and boom:
compression
lower skin and boom:
tension
web: shear
Wing loading = weight ÷ wing area
60 000 kg on 120 m² → 500 kg/m²
In modern stressed-skin wings the bending is shared by the spars and the skin.
Maximum bending moment: at the wing root.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
A cantilever wing is built around one or more spars, the main load-bearing beams running from root to tip. A spar has flanges, also called booms, at the top and bottom, joined by a thin web. When the wing bends, the flanges carry the tension and compression and the web carries the shear. In flight the lift bends the wing upwards and backwards and also twists it, so the upper skin and boom are in compression and the lower skin and boom in tension. On the ground the weight of the wing reverses that. In a modern stressed-skin wing the skin is attached to the spar booms and shares the bending, so bending loads are carried by both the spars and the skin. The bending moment is greatest at the root, where the whole wing is trying to lever itself off. And remember wing loading: weight divided by wing area, for example sixty thousand kilograms on a hundred and twenty square metres is five hundred kilograms per square metre.
Part 1 · Wings
The torsion box: spars, ribs, stringers and skin Front and rear spars , the skin , the ribs and the stringers form a closed torsion box The box resists bending and twisting ; the same box girder idea is used in fins and stabilisers Skin : takes the air pressure loads and fuel inertia, carries spanwise bending stresses and resists torsionStringers : spanwise members that stiffen the skin against buckling in compressionRibs : keep the aerofoil shape, support skin and stringers, feed in engine, gear and control loads; lightening holes save weight and stiffen
Wing section: the torsion box
front spar
rear spar
torsion box
skin + spars + ribs + stringers (green)
A rib, seen from the side
flanged lightening holes: lighter and stiffer
Ribs keep the aerofoil shape and feed engine, gear and control loads into spars and skin.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
A conventional wing has a front spar and a rear spar, and between them the upper and lower skins, the ribs and the stringers form a closed box. Watch the scene as the upper skin lifts away so you can see inside. The spars run along the wing. The ribs run across it, keeping the aerofoil shape, supporting the skin and stringers against buckling, and feeding concentrated loads from engines, landing gear and control surfaces into the spars and skin. Ribs have flanged lightening holes, which save weight and actually stiffen the rib. The stringers run spanwise and stiffen the skin, especially the upper skin, which is in compression in flight. And the skin closes the box. A closed box is extremely good at resisting twisting, which is why it is called the torsion box, and the same box girder idea is used in fins and stabilisers. In many aircraft the box is sealed and becomes the fuel tank.
Part 1 · Wings
Bending relief: fuel and engines in the wing Mass carried in the wing pushes down where lift pushes up: less bending at the root Wing fuel is used last , so the relief lasts as long as possibleWing-mounted engines also relieve bending, and act as mass balance against flutterMZFM : maximum permissible mass with no usable fuel ; it limits the load in the fuselageAround the engine mountings the wing sees large tension and torsion loads
root
0.2
0.4
0.6
0.8
tip
distance from root (fraction of semi-span)
wing bending moment
no mass in the wing
wing fuel + wing engines
30 % less at the root
Same aircraft weight, same lift. Mass carried in the wing pushes down
where the lift pushes up, so the root bending moment falls.
So: wing fuel is used last , and the MZFM limits the load
carried in the fuselage, which gets no such relief.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a neat trick of wing design. The lift pushes the wing up, but any mass carried inside the wing pushes it down at the same place, so it cancels part of the bending. Look at the graph: for the same aircraft weight, putting fuel in the wing tanks and engines on the wing cuts the bending moment at the root by about thirty per cent. In the scene, the centre tank is used first and the wing tanks last, so the relief lasts as long as possible, which matters most at high weights with the outer tanks full. The engines on the wing help in the same way, and because they hang forward on pylons they also act as mass balances against wing flutter. This also explains the maximum zero fuel mass, the maximum permissible mass with no usable fuel: load in the fuselage gets no such relief, so it must be limited. Near the engine mountings, the wing carries large tension and torsion loads.
Part 1 · Wings
Engines on the wing or on the rear fuselage? On the wing : bending relief, so a lighter wing ; engines ahead of the wing damp flutterBut an engine failure gives a large yaw , and thrust below the CG changes the pitch Rear fuselage : close to the centre line, so engine failure gives little yaw : fewer asymmetric problemsThrust changes have less effect on yaw and pitch No relief: the wing must be stronger and heavier ; usually a T-tail, with its deep-stall risk
Engines on the wing
Engines on the rear fuselage
+
bending relief: a lighter wing
+
engines ahead of the wing damp flutter
+
easy access for maintenance
−
engine failure: large yaw
−
thrust below the CG: pitch changes
+
clean wing, quieter cabin
+
engine failure: little yaw
+
less yaw and pitch change with thrust
−
no relief: stronger, heavier wing
−
T-tail: deep-stall risk
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where should the engines go? Hang them under the wing and you get the bending relief we have just seen, so the wing can be lighter, and engines on pylons ahead of the wing help prevent flutter. But an engine under the wing is a long way from the centre line, so if one fails there is a large yawing moment to control. And because the thrust line is below the centre of gravity, every power change gives a pitch change. Put the engines on the rear fuselage instead and they sit close to the centre line: an engine failure gives very little yaw and fewer asymmetric problems, and thrust changes have less effect on yaw and pitch. The price is that the wing loses its relief, so it must be stronger and heavier, and rear-engined types usually need a T-tail, which brings the risk of a deep stall. For the exam: rear engines mean less control trouble after an engine failure, but a stronger wing.
Part 2 · Tail and controls
Tail units Layouts: conventional, T-tail, H-tail, V-tail ; some types use a canard foreplane instead The tailplane gives longitudinal stability , making up or down forces as needed The fin gives directional stability with side forces Elevators or a moving tailplane give pitch control; the rudder gives directional controlBuilt like small wings; both see bending and torsion ; may hold trim fuel tanks
Tail units, seen from behind
Conventional
T-tail
H-tail (twin fin)
V-tail
blue: horizontal stabiliser · orange: fin · purple: combined surfaces
Tailplane
longitudinal stability (up or down force); elevator
or moving tailplane: pitch control
Fin
directional stability (side force); rudder:
directional control
Structure
small wings: spars, ribs, stringers, skin; bending
and torsion
Extras
may hold trim fuel tanks; canards (foreplanes)
replace the tail on some types
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The tail unit, or empennage, comes in several layouts: the conventional tail with the tailplane on the fuselage, the T-tail with the tailplane on top of the fin, the H-tail with a fin at each end of the tailplane, and the V-tail, whose two inclined surfaces do the work of both. Some aircraft put a foreplane, a canard, at the front instead. Whatever the layout, the jobs are the same. The horizontal surface, the tailplane or horizontal stabiliser, gives longitudinal stability by producing an up or down force as required, and its elevators, or the whole tailplane if it moves, give pitch control. The vertical surface, the fin, gives directional stability with side forces, and the rudder gives directional control. Structurally these are small wings, with spars, ribs, stringers and skin, and both suffer bending and torsion. On some aircraft the tailplane is sealed to carry fuel for trimming the centre of gravity.
Part 2 · Tail and controls
The three axes All three axes pass through the centre of gravity Longitudinal axis, nose to tail: motion about it is roll Lateral axis, wingtip to wingtip: motion about it is pitch Normal axis, at right angles to both: motion about it is yaw If the moments about an axis do not add to zero, the aircraft accelerates angularly about it
longitudinal axis: ROLL
lateral axis: PITCH
CG
normal axis: YAW
(through the CG, at right
angles to the page)
All three axes
pass through the centre of gravity
Net moment = 0
no angular acceleration: steady rate or none
Net moment ≠ 0
angular acceleration about that axis
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every control surface works by making the aircraft rotate about one of three axes, and all three pass through the centre of gravity. Watch them appear. The longitudinal axis runs from nose to tail, and rotation about it is roll. The lateral axis runs from wingtip to wingtip, and rotation about it is pitch. The normal axis runs at right angles to both, vertically through the CG when the aircraft is level, and rotation about it is yaw. Now the aircraft rolls about its longitudinal axis. Here is a point the exam likes. If all the moments about an axis add up to zero, the aircraft is in equilibrium about that axis: it is either not rotating or rotating at a steady rate. If they do not add up to zero, there is an angular acceleration about that axis, just as an unbalanced force gives a linear acceleration. Equilibrium is not the same as stability; that depends on what happens after a disturbance.
Part 2 · Tail and controls
Combined control surfaces Flaperon : aileron + flap; both down together for lift, differentially for rollElevon : elevator + aileron, on tailless and delta aircraftRuddervator : rudder + elevator, on a V-tailStabilator : an all-moving tailplane: longitudinal stability and pitch control , and it trimsA stabilator is a more powerful pitch control than an elevator
whole trailing edge
Flaperon
aileron + flap
both sides down together for lift
differentially for roll
Elevon
elevator + aileron
tailless and delta aircraft
Ruddervator
rudder + elevator
on a V-tail
Stabilator
all-moving tailplane
stability, pitch control and trim
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some aircraft combine two controls in one surface. A flaperon is a combined aileron and flap: both flaperons go down together to act as flaps, and move differentially, one up and one down, to roll the aircraft. An elevon is a combined elevator and aileron, used on tailless and delta-winged aircraft: together they pitch, differentially they roll. A ruddervator is a combined rudder and elevator, found on V-tails: moving together they act as elevators, moving in opposite directions they act as a rudder. Finally, the stabilator is an all-moving tailplane. The whole surface pivots, so it provides the longitudinal stability of a tailplane and the pitch control of an elevator in one piece, and it can be set to trim. Because the whole surface moves, a stabilator is a more powerful pitch control than an elevator, which is why it is common on fast aircraft and on light aircraft that need strong pitch control at low speed.
Part 2 · Tail and controls
Trimming with a variable-incidence tailplane A screw jack moves the whole stabiliser; the trim angle depends on speed, thrust and CG In trim the elevator is streamlined (neutral) with the stabiliser: full elevator authority remains Better than a trim tab: more effective trimming while keeping pitch control authority No trim tabs on an all-moving tailplane: the whole surface trims Underwing engines: more thrust gives nose up , so trim with elevator down ; the stabiliser gives pitch control if the hydraulics fail
Trimmable horizontal stabiliser
pivot
screw jack moves the leading edge
elevator streamlined
when in trim
Trim setting depends on speed, thrust and CG
CG
more thrust below the CG
nose-up moment
Underwing engines: thrust up → nose up → trim with elevator down
Forward CG, low speed or flap → more nose-up stabiliser trim
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Large jets trim in pitch by moving the whole horizontal stabiliser. It pivots near its rear spar, and a screw jack moves its leading edge up or down. The setting needed depends on the speed, the thrust and the position of the centre of gravity, so there is no single trim angle. When the aircraft is in trim, the elevator lies streamlined with the stabiliser, so the pilot keeps the full elevator range for manoeuvring. That is the big advantage over a fixed tailplane with a trim tab: trimming is far more powerful, and pitch control authority is not used up. An all-moving tailplane does not need trim tabs at all, because the whole surface trims. Now a trim case. Engines under a low wing put the thrust line below the CG, so more thrust gives a nose-up moment, which has to be held with down elevator until you retrim. And because the stabiliser has its own drive, it can be used for pitch control if the main hydraulics fail.
Part 2 · Tail and controls
Roll control on a fast swept wing Krueger flaps on the inboard leading edge, slats outboardAt high speed the outboard ailerons are locked out : they would twist the flexible outer wing Cruise roll control: inboard ailerons and/or roll spoilers Wheel to the left: left aileron up, left spoiler up ; right aileron down, right spoiler stays down Inboard surfaces act near the stiff root, so they reduce the risk of aileron reversal
A swept jet wing, from above
Krueger flaps (inboard)
slats (outboard)
inboard (high-speed) aileron
outboard aileron
flaps
spoilers
Outboard ailerons are locked out at high speed; inboard ailerons and roll spoilers take over.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
A large swept wing carries many moving surfaces. On the leading edge you will usually find Krueger flaps inboard, near the root, and slats outboard. On the trailing edge there are flaps, with an aileron near the tip and often a second, high-speed aileron inboard, between the flaps. Ahead of the flaps are the spoiler panels. At high speed the outer wing is long and flexible, and a big outboard aileron deflection would twist it. So at high speed the outboard ailerons are locked out, and roll control comes from the inboard ailerons and the roll spoilers, which act near the stiff root. Follow the drawing as the wheel goes to the left. The left aileron goes up and the left spoilers rise with it, spoiling lift on that wing. The right aileron goes down, and the right spoilers stay down; a spoiler can only rise. When the wheel returns to neutral, everything streamlines again.
Part 3 · Aeroelastic effects
Aileron reversal and divergence Aileron reversal : a down aileron twists a flexible wing nose down; above the reversal speed the wing loses lift and rolls the wrong wayMost likely at high speed , and with fully powered controls, which give full deflection regardless of load Divergence : lift at a CP ahead of the torsional axis twists the leading edge up, more lift, more twist, failureCaused by weak (flexible) wings, high speed, CP forward of the torsional axis Swept-back wings are less prone to divergence: bending washes the tip out
Aileron reversal
aileron down: lift far aft
wing twists nose down
roll response
speed →
reversal
High speed + flexible wing + full deflection: fully powered controls make it likelier.
Divergence
torsional (flexural) axis
lift at the CP, ahead of the axis
lift twists the leading edge up
→ more angle of attack
→ more lift → more twist
until the wing fails
Most likely: high speed, weak (flexible) wing, CP ahead of the torsional axis .
Sweepback helps: bending a swept wing twists its tip nose down.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
A wing is not perfectly stiff, and at high speed its flexibility can bite. First, aileron reversal. At low speed the twist is small and the aileron wins. But the twisting grows with the square of the speed, and above the reversal speed the nose-down twist removes more lift than the aileron adds, so the aircraft rolls the wrong way. Reversal is most likely at high speed, and with fully powered controls, because a manual pilot could never force full deflection at that speed. Hence inboard ailerons and spoilers. Divergence is related. If the centre of pressure is ahead of the torsional axis, lift twists the leading edge up, which increases the angle of attack, which increases the lift and the twist, until the wing fails. It needs a weak wing, high speed and a forward centre of pressure. Swept-back wings are less prone, because bending twists their tips nose down.
Part 3 · Roll spoilers
Roll spoilers, speed brakes and adverse yaw Roll spoilers rise on the down-going wing (the one with its aileron up)As speed brakes they rise together on both wings, from a separate lever Speed brakes out and roll left: the left spoiler rises further, the right retracts The extra drag on the down-going wing yaws the nose into the turn: roll spoilers reduce adverse yaw Other cures: differential ailerons , Frise ailerons, rudder coordination; a yaw damper damps Dutch roll
Seen from behind
1 Wheel turned left: roll left
left wing
right wing
left aileron UP + left spoiler UP; right aileron down, right spoiler stays down
2 Speed brakes out: both sides up together
left wing
right wing
3 Speed brakes out, then roll left
left wing
right wing
left spoiler rises further, right spoiler retracts from the speed-brake setting
The spoiler is up on the down-going wing: its drag yaws the nose INTO the turn,
so roll spoilers also reduce adverse yaw . No twist: no reversal.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Roll spoilers are plates on the upper surface that rise to spoil lift. When you roll, they rise on the down-going wing, the same wing whose aileron goes up. Look at the first picture: wheel to the left, left aileron up, left spoiler up, right aileron down and right spoiler stays down. The same panels can work as speed brakes, selected by a separate lever, when they rise together on both wings. If you then roll with the speed brakes out, the spoilers move differentially from the speed-brake position: on a left roll the left spoiler goes up further and the right one retracts. There is a bonus. A down-going aileron adds drag on the rising wing, which yaws the nose away from the turn; that is adverse yaw. A raised spoiler adds drag on the down-going wing instead, so roll spoilers reduce adverse yaw. Differential ailerons do the same job on lighter aircraft. A yaw damper, by contrast, damps Dutch roll, improving lateral and directional stability.
Part 3 · Balance and tabs
Aerodynamic balance: easing the hinge moment Hinge moment = air load on the surface × its distance behind the hinge: this is what the pilot must holdAerodynamic balance reduces the hinge moment, and so the stick forceInset hinge : hinge moved back, close to but ahead of the surface's centre of pressureHorn balance : area ahead of the hinge line; internal balance : a sealed nose uses the pressure differenceBalance tabs ; never put the hinge behind the CP, or the control would snatch (overbalance)
Hinge moment and how to reduce it
hinge
air load at the surface's CP
arm
Hinge moment = air load × arm. Shorten the arm and the stick force falls.
Inset hinge
hinge set back, closer to (but ahead of) the CP
Horn balance
area ahead of the hinge at the tip
Internal balance
seal
sealed nose in a cove: pressure difference helps
Balance tab
tab moves opposite to the surface
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a control surface is deflected, the air load on it acts at its own centre of pressure, some distance behind the hinge. That load times that distance is the hinge moment, and it is what the pilot has to hold. The simplest is the inset hinge: move the hinge line back, closer to the surface's centre of pressure, so the arm is shorter; but always keep it just ahead of the centre of pressure, otherwise the surface would overbalance and snatch. A horn balance puts some of the surface area ahead of the hinge line at the tip, where the air load on it helps the pilot. An internal balance puts a sealed nose inside a cove, so the pressure difference above and below the wing pushes on it and helps. And a balance tab, which we meet next, does the job with a small surface at the trailing edge. Remember: weights are mass balance, not aerodynamic balance.
Part 3 · Balance and tabs
Trim tabs Purpose: reduce the stick holding force to zero by cancelling the hinge moment To hold the elevator up , the trim tab moves down ; trimming does not move the elevator A trim tab moves only when trimmed , not when the pilot moves the surface Rudder trim and rudder pedals work in the same direction ; in power-assisted systems tabs trim the force to zero Manual reversion: trim tabs can fly the aircraft; on a locked fully powered surface a tab works in reverse
Holding the elevator up with a trim tab
elevator UP
tab DOWN
tab air load
The tab's small force on a long arm balances the elevator hinge moment:
stick force zero, elevator stays exactly where it was.
Purpose
reduce the holding (stick) force to zero: cancel
the hinge moment
Moves
only when the trim control is moved; not when the
elevator moves
Cockpit
trim wheel and rudder trim move in the natural
sense
Manual reversion
trim tabs can be used to fly in pitch after a
hydraulic failure
Fully powered
surface locked by its jacks: a tab alone acts in
reverse
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
A trim tab is a small surface at the trailing edge of a control, set from the cockpit, whose only purpose is to reduce the force the pilot must hold to zero. Suppose a forward centre of gravity means the elevator must be held up. The tab moves down, the air load on it acts on a long arm behind the hinge, and it cancels the elevator's hinge moment. The stick force falls to zero, and the elevator does not move at all; it simply stays where the pilot was holding it. The tab moves only when the trim is operated. If hydraulic power fails in a power-assisted system, trim tabs can be used to fly the aircraft. But if a fully powered surface is locked by its jacks, the tab acts alone like a tiny elevator, so it works in reverse: tab up then means nose up.
Part 3 · Balance and tabs
Balance, anti-balance, servo and spring tabs Balance tab : geared to move opposite the surface; lighter forces, slightly less effectAnti-balance tab : moves the same way ; heavier forces, more feelServo tab : the pilot moves only the tab and the air load flies the surface; weak at low speed ; sometimes also trimsServo tab with a jammed surface: limited control in the opposite sense Spring tab : a spring in the linkage; acts as a servo tab only when forces are high, so it reduces hinge moments at high speed
Balance tab
fixed link
geared to move OPPOSITE the surface
lighter controls, a little less effect
Anti-balance tab
fixed link
geared to move the SAME way
heavier controls: more feel and effect
Servo tab
from the stick to the tab
pilot moves only the tab; the surface floats
light, but weak at low speed (low q)
Spring tab
spring in the stick linkage
spring in the linkage: acts as a servo tab
only when forces are high: high speed
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The other tabs are geared into the control system. A balance tab is linked so that it moves opposite to its surface: when the elevator goes down, the tab goes up, and its air load helps move the surface, making the controls lighter. An anti-balance tab moves the same way as the surface, making the controls heavier; it adds feel and effectiveness to an over-light control. A servo tab is different again. The pilot's controls move only the tab, and the air load on the tab moves the free-floating surface: light forces, but weak at low speed. Some servo tabs can also be set to trim, and they can sometimes provide control after a hydraulic failure. If the main surface jams, the tab gives only limited control, in the opposite sense. A spring tab has a spring in its linkage: at low speed it moves the surface directly, and only at high speed, when forces are big, does the spring give and the tab start helping.
Part 3 · Flutter
Flutter and mass balance Flutter : a rapid, uncontrolled oscillation of a control or its surface; can destroy the structure; must not occur in the envelopeCaused by aerodynamic, inertia and elastic forces interacting; control CG aft of the hinge lets it lag Torsional aileron flutter couples with wing twisting ; flexural with wing bending ; wing flutter = twisting + flappingCure: mass balance , weights ahead of the hinge , bringing the CG towards or ahead of the hinge line Backlash and wear can let flutter start below the limit speed; wing engines act as mass balance
Why an unbalanced aileron flutters
hinge
aileron CG
aft of the hinge
wing moves up
aileron lags:
effectively DOWN
Inertia makes the aileron lag the wing. Its extra lift drives the wing
further; the cycle repeats and grows. Wing bending: flexural flutter;
wing twisting: torsional flutter. Wing flutter itself: twisting + flapping.
The cure: mass balance
weight ahead of the hinge
aileron CG now on or ahead of the hinge line
Keep backlash low: worn hinges and slack cables let flutter start below the limit speed.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flutter is a rapid, uncontrolled oscillation of a control surface, or of the wing or tail it is attached to,, and it can destroy the structure in seconds. It comes from the interaction of aerodynamic forces, inertia forces and the elasticity of the structure. Watch the scene: the wing bends and twists, and the aileron, whose centre of gravity is behind its hinge, lags behind the wing's motion, so it is effectively deflected the wrong way and its extra lift drives the wing further each cycle. Coupled with wing twisting this is torsional flutter; coupled with wing bending, flexural flutter. Wing flutter itself combines twisting and flapping. The cure is mass balance. A weight fixed ahead of the hinge brings the control's centre of gravity onto or ahead of the hinge line and changes its natural period, so it no longer lags. Worn hinges or slack cables, called backlash, can let flutter start below the limit speed, and the engines on their pylons act as mass balances for the wing.
Part 3 · Powered controls
Power-assisted, fully powered and fly-by-wire Power assisted : a jack helps, but the pilot feels a proportion of the air load, so forces still rise with speed After hydraulic failure, the pilot flies it manually , helped by trim tabs or the trimmable stabiliser Fully powered : irreversible; no air load reaches the pilot, so stick forces are low : artificial feel is neededFly-by-wire : computers and wires replace cables: lighter , but jacks still need hydraulic powerBig, fast aircraft need power: forces would otherwise be far too high
Manual
stick → cables/rods → surface
pilot feels the full air load
air load felt
100 %
Power assisted
stick → servo valve + jack → surface
pilot feels a set proportion of the load
air load felt
25 %
Fully powered
stick → servo valve → jacks (irreversible)
no air load fed back: artificial feel added
air load felt
feel unit
Fly-by-wire
stick → computers → wires → jacks
lighter, no long cable runs; still hydraulic jacks
air load felt
feel unit
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
On large, fast aircraft the hinge moments are far too large to hold by hand, so the controls are powered. In a power-assisted system, a hydraulic jack does most of the work, but the linkage is arranged so the pilot still feels a set proportion of the air load. That means the stick forces still rise with speed, which is natural, and if the hydraulics fail the pilot can still fly the aircraft manually, helped by trim tabs or the trimmable stabiliser. A fully powered system is irreversible. The pilot's input only moves a servo valve, the jacks move the surface, and none of the air load comes back to the stick. So the stick forces would be very low and the same at all speeds, and an artificial feel system has to be added. Fly-by-wire takes the next step: the pilot's inputs go as electrical signals to computers, which command the jacks. It is lighter than long cable runs, but the surfaces are still moved by hydraulic jacks.
Part 3 · Powered controls
Artificial feel, springs and bob weights Q-feel : senses dynamic pressure (pitot − static); force rises with ½ρV² ; fitted in parallel with the pitch controlDown spring : pulls the stick forward, increasing the stick-force gradient Bob weight : a mass in the control run that increases stick force in a pull-up , in proportion to gCG at the forward limit : more elevator needed, so higher longitudinal stick forcesMach trim : trims nose up at high Mach to stop the nose-down tuck
0
50
100
150
200
250
300
350
0
25
50
75
100
indicated airspeed (kt)
stick force for the same deflection (%)
Q-feel: rises with ½ρV²
simple spring feel: the same at every speed
Q-feel unit
senses pitot minus static; fitted in parallel with the pitch control run
Down spring
pulls the stick forward: increases the stick-force gradient
Bob weight
a mass on the control run: heavier stick in a pull-up (with g)
Forward CG
more elevator needed: higher longitudinal stick forces
Mach trim
trims nose up automatically at high Mach: stops the tuck
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Artificial feel gives the pilot of a powered control the forces that the air would have given. A Q-feel unit senses dynamic pressure, pitot minus static, so the force for a given deflection rises with half rho V squared, just like a real control. It acts on the control run in parallel with the pitch control. Designers have other tools. A down spring pulls the stick forward with a constant force, which increases the stick-force gradient and makes the aircraft feel more stable. A bob weight is a mass in the control run; in a pull-up the g loading makes it heavier, so the stick force rises in proportion to g and over-stressing is harder. Remember too that a centre of gravity at the forward limit needs more elevator, so the longitudinal stick forces are higher. Finally, Mach trim automatically trims nose up at high Mach numbers, to counter the nose-down tuck as the centre of pressure moves aft.
Part 4 · Materials
Airframe metals Material Strengths Weaknesses Typical use Aluminium alloys (duralumin: Al + Cu) Good strength-to-weight, good fatigue resistance , conducts heat and electricity Poor corrosion resistance unless clad with pure aluminium; difficult to weld Most of the airframe: skins, spars, ribs, rivets Steel and its alloys Very strong, hard wearing Heavy Only where strength is vital: gear, fittings, bolts Titanium Much lighter than steel; keeps strength and corrosion resistance to about 400 °C Expensive, hard to machine Firewalls and fireproof bulkheads, hot areasMagnesium alloys Very light (aluminium is 1.5 times heavier) Poor elastic properties; corrodes easily ; burns fiercely (sand or dry powder) Limited, non-primary parts: wheels, castings
Each material is chosen for its fatigue strength, wear resistance, strength-to-weight ratio, fire resistance and corrosion behaviour.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each airframe material is chosen for a particular mix of properties. Aluminium alloys make up most of the structure because they have a good strength to weight ratio, and the duralumin type, aluminium alloyed with copper, dominates because of its good fatigue resistance. Its weaknesses are poor corrosion resistance, unless it is clad with a thin layer of pure aluminium, and that it is difficult to weld, so it is riveted or bonded. Steel is only used where strength is vital and the weight can be accepted, such as landing gear and highly loaded fittings. Titanium is much lighter than steel and keeps its strength and corrosion resistance up to about four hundred degrees Celsius, so it is the material for firewalls and fireproof bulkheads. Magnesium alloys are very light, aluminium is one and a half times heavier, but their elastic properties are poor, they corrode easily and they burn fiercely; a magnesium fire is fought with sand or dry powder, never water.
Part 4 · Materials
Composite materials Reinforcing fibres (glass, carbon, aramid) in a resin : GRP, CFRP, often with honeycomb cores High specific strength and stiffness , good corrosion resistance , complex shapesFatigue is different: little concern below about 80 % of ultimate; strength is lost gradually Weaknesses: hidden impact damage, erosion, moisture, toxic fumes when burning ; the resin has the lowest melting point Now used throughout modern structures: control surfaces, fairings, floors, cowlings, empennage
Fibres in a resin, laid where the load goes
plies at 0°, ±45°, 90°
give strength in the
directions needed
For
• high specific strength and stiffness
• resist corrosion well
• complex shapes in one piece
• lose strength gradually (warning)
Against
• hidden damage after impacts
• eroded by hail and sand: sheath edges
• can absorb moisture if not sealed
• toxic fumes in a fire; hard to repair
Where: fairings, control surfaces, flaps, floor panels, cowlings,
empennage and, on the newest types, whole wings and fuselages.
GRP: glass-reinforced plastic · CFRP: carbon-fibre-reinforced plastic
The resin softens at a far lower temperature than any structural metal.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Composite materials are made of strong fibres, glass, carbon or aramid, set in a resin, and laid up in plies at different angles so the strength goes where the loads go. Glass-reinforced plastic and carbon-fibre-reinforced plastic are the common ones, often bonded over a honeycomb core. Their attraction is high specific strength and specific stiffness, meaning strength and stiffness per kilogram, together with good corrosion resistance and the ability to make complex shapes in one piece. Their fatigue behaviour is different from metal. Below about eighty per cent of ultimate stress fatigue is hardly a consideration, and when they do degrade they lose strength gradually, whereas a fatigued metal keeps its strength until it fails suddenly. The drawbacks are impact damage that may be hidden inside, erosion by hail and sand, moisture absorption if poorly sealed, difficult repairs, and toxic fumes in a fire, though a composite fire can be fought with water. And the resin softens and melts at a far lower temperature than aluminium, titanium or steel.
Part 4 · Corrosion
Corrosion: metal going back to ore Corrosion : slow destruction of a metal by electro-chemical action, returning it towards its oreNeeds an electrolyte (water); worse with salt and sulphur ; also between dissimilar metals or alloy constituents An oxide film protects some metals, but it can crack, flake or let oxygen through Worst in tropical, industrial and marine air; least in arctic and rural air Evidence: rust on steel, white or grey powder on aluminium and magnesium, blue-green on copper
time
oxide film thickness
the film protects
and growth slows
Corrosion rate by atmosphere
High
tropical · industrial · marine
Moderate
temperate · suburban · inland
Low
arctic · rural
What corrosion looks like
Steel
reddish-brown powder: rust
Aluminium, magnesium
white to grey powder; magnesium pits deeply
Copper alloys
blue-green salt deposit
Needs an electrolyte (water); salt and sulphur make it worse.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most metals are unstable. Corrosion is their slow return towards the stable compounds of the ore they came from, oxides, hydroxides, carbonates and other salts, and it is largely electro-chemical. Tiny electrical cells form in or on the metal wherever there is an electrolyte, usually water, and the attack is worse when that water carries impurities such as industrial sulphur or sea salt. It also happens where two dissimilar metals touch, or between the different constituents of an alloy. When bare metal meets air it forms an oxide film, which on some metals protects what lies beneath, so the growth slows down, as the graph shows. But the film can crack, flake or let oxygen through, and the attack continues. The rate depends on where the aircraft operates: highest in tropical, industrial and marine air, moderate in temperate and suburban air, lowest in arctic and rural air. Learn the evidence: reddish-brown rust on steel, white or grey powder on aluminium and magnesium, and blue-green deposits on copper alloys.
Part 4 · Corrosion
Three types of corrosion
Surface corrosion
white or grey powder on the surface
uniform etching or pitting: visible, so the least dangerous
Intergranular corrosion
hairline cracks only at the surface
runs along grain boundaries inside the metal: the most dangerous
Stress corrosion
little visible evidence, no loss of metal
steady tensile stress + corrosion: a crack grows from a pit
Surface Fairly uniform attack that thins the metal. Seen as etching, pitting and powder, so it is found early: the least damaging .
Intergranular Runs along grain boundaries inside the metal, faster under stress. Only hairline cracks show: the most dangerous . Parts are rejected.
Stress corrosion A steady tensile stress plus corrosion: a pit concentrates stress and a crack grows to failure, with little visible evidence .
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Corrosion takes several forms, and they often occur together. It shows as etching, pitting and powdery deposits, so it can be found and treated early; that makes it the least damaging kind. Intergranular corrosion is the opposite. It penetrates into the metal along the grain boundaries, because the boundaries are anodic to the grain centres, and stress speeds it up. The only sign at the surface may be a line of hairline cracks visible through a magnifying glass, and there is no way of knowing how much strength has been lost, so any part found with it must be rejected immediately. It is the most dangerous form. Stress corrosion cracking needs a steady tensile stress, built in during manufacture or assembly, or applied in service, together with a corrosive environment. A small pit concentrates the stress, a crack starts and grows under the combined action until the part fails, often with little visible evidence and no apparent loss of metal.
Part 4 · Heavy landings
Heavy landings Gear designed for a maximum descent rate of 10 ft/s (about 3 m/s) at maximum landing weight Exceed either and the gear, its supporting structure, fuselage and wings may be damaged Also overstress: landing with drift , or in an abnormal attitude, nose or tail wheels first Primary areas: gear and its attachments, wing and tail attachments, engine mountings ; secondary : fuselage skinsCrew report weight, fuel distribution, conditions and any noises ; some aircraft have heavy-landing indicators
Where to look after a heavy landing
primary: gear and its supporting structure, wing and tail
attachments, engine mountings
secondary: fuselage upper and lower skin and structure
Design case: 10 ft/s (3 m/s) descent at maximum landing weight
Also overstress: landing with drift, or nose or tail wheels first
Crew report: weight, fuel distribution, conditions, any noises heard
No damage in primary areas: secondary areas may not need checking
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The landing gear is designed to absorb a landing at a particular weight and a particular rate of descent, typically ten feet per second, about three metres per second, at the maximum landing weight. Watch the shock strut at touchdown: the landing load drives it up, nitrogen is compressed and oil is forced through the orifice, then it settles to the static position. If the weight or the descent rate is exceeded, the strut cannot absorb all the energy, and the overload passes into the gear, its supporting structure and on into the wings and fuselage. After a suspected heavy landing the crew must report the weight, the fuel distribution, the landing conditions and any noises that suggested structural failure. Engineers inspect the primary areas first: the landing gear and its attachments, the wing and tailplane attachments and the engine mountings. On some types, if those are clear, the secondary areas, the fuselage skins, need not be inspected; if damage is found, the inspection continues.
Part 4 · Safety targets
How likely may a failure be?
10−2
10−3
10−4
10−5
10−6
10−7
10−8
10−9
10−10
No safety effect
no requirement
Minor
≤ 10−3 per flight hour
Probable
Major
≤ 10−5 per flight hour
Remote
Hazardous
≤ 10−7 per flight hour
Extremely remote
Catastrophic
≤ 10−9 per flight hour
Extremely improbable
allowed
probability
(log scale)
more severe effect → must be less likely
No single failure may be catastrophic. Catastrophic failure conditions must be extremely improbable : about 1 in 109 per flight hour.
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Certification rules link how serious a failure would be to how often it may happen: the worse the effect, the less likely it must be. No safety effect has no probability requirement. A minor failure, a slight reduction in margins, may be probable, up to about one in a thousand per flight hour. A major failure, a significant reduction in margins or a significant increase in workload, possibly with injuries, must be remote, about one in a hundred thousand. A hazardous failure, a large reduction in margins, excessive workload or serious injury to a few occupants, must be extremely remote, about one in ten million. And a catastrophic failure, multiple deaths and usually the loss of the aeroplane, must be extremely improbable, about one in a thousand million per flight hour. And no single failure may be catastrophic. The one in a thousand million figure came from sharing a target of one in ten million among about a hundred potential catastrophic failure conditions.
Summary
Wings, controls and materials in a nutshell Wing structure Spars, ribs, stringers and skin form the torsion box. Max bending at the root. Wing fuel used last; MZFM.
Engines On the wing: relief, lighter wing, flutter damping. Rear fuselage: little yaw after failure, but a stronger wing.
Controls Axes through the CG. Flaperon, elevon, ruddervator, stabilator. Trimmable stabiliser. Inboard ailerons and roll spoilers at speed.
Balance and tabs Aero balance cuts hinge moments; mass balance ahead of the hinge stops flutter. Trim, balance, anti-balance, servo, spring tabs.
Aeroelastic Reversal: high speed, fully powered. Divergence: weak wing, high speed, CP ahead of the torsional axis.
Materials and safety Duralumin, titanium firewalls, magnesium burns. Intergranular corrosion worst. 10 ft/s landings. Catastrophic: 10−9 .
Chapter 2 · Wings, Stabilisers, Materials and Corrosion
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the lesson together. The wing is a torsion box of spars, ribs, stringers and skin, with its greatest bending moment at the root; fuel in the wing, used last, and engines on the wing relieve that bending, and the maximum zero fuel mass limits the load in the fuselage. Rear engines mean little yaw after an engine failure but a stronger wing. All three axes pass through the CG. Combined surfaces include flaperons, elevons, ruddervators and stabilators, and big jets trim with a moving stabiliser, controlling roll at speed with inboard ailerons and roll spoilers. Aerodynamic balance reduces hinge moments; mass balance ahead of the hinge prevents flutter; and the tab family trims or lightens the controls. Reversal and divergence come with high speed and flexible wings. Aluminium alloys dominate, titanium makes firewalls, magnesium burns, and intergranular corrosion is the most dangerous. Gear is designed for ten feet per second, and catastrophic failures must be extremely improbable. Now try the quiz.