Aircraft Systems · Chapter 7
Brakes, Anti-skid and Autobrake How aircraft brakes turn kinetic energy into heat, how multi-disc steel and carbon brakes are built, adjusted and checked, how anti-skid and autobrakes work, and how to handle hot brakes and wheel fires.
KINETIC ENERGY → HEAT
rotors keyed to the wheel · stators keyed to the axle
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter seven is about stopping. Every landing ends with tonnes of aircraft moving at well over one hundred knots, and most of that energy has to disappear as heat in a few brake packs hidden inside the wheels. We will look at how a multi-disc brake is built, why carbon has replaced steel on many aircraft, how brakes are adjusted and checked for wear, and what brake fade and brake drag are. Then we follow the brake systems of light and large aircraft, and the clever pieces of automation, anti-skid and autobrake, that let you brake as hard as the runway allows. We finish with brake energy, cooling times, temperature warnings and the right way to deal with a wheel fire.
Chapter 7 roadmap
Stopping the aircraft 1 · The brake itself Energy to heat, drum, single and multi-disc brakes, steel versus carbon .
2 · Keeping it healthy Adjusters and running clearance, wear pins , fade and drag .
3 · Brake systems Light aircraft master cylinders and differential braking ; normal, alternate, accumulator and parking.
4 · Anti-skid Why slip matters, wheel deceleration sensing, touchdown, skid and locked-wheel protection.
5 · Autobrake Landing settings, RTO above 85 kt , arming and the ways it disarms .
6 · Heat and fire Brake energy zones, cooling times, temperature warnings, dry powder and safe approach.
Chapter 7 · Brakes, Anti-skid and Autobrake
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This chapter is about stopping. First the brake itself: where the energy goes, the drum, single disc and multi-disc brakes, and why many aircraft now use carbon instead of steel. Second, how a brake is kept healthy: the adjusters that set the running clearance, the wear pins that show how much lining is left, and the two classic faults, brake fade and brake drag. Third, the systems that feed the brakes: master cylinders and differential braking on a light aircraft, and on a large aircraft the normal and alternate hydraulic supplies, the accumulator and the parking brake. Fourth, anti-skid, which lets you brake as hard as the runway allows without locking a wheel. Fifth, the autobrake, with its landing settings and the rejected take-off mode. Finally, heat and fire: brake energy charts, cooling times, temperature warnings, and how to deal safely with hot brakes and wheel fires.
Part 1 · The brake itself
From kinetic energy to heat Brakes use friction to turn the aircraft's kinetic energy into heat KE = ½ m V²: energy grows with the square of speed Worked example · A320 landing
1 Mass and touchdown speedm = 64 t = 64 000 kg, V = 135 kt
2 Knots to metres per second (× 0.514)V = 135 × 0.514 = 69.4 m/s
3 Square the speedV² = 69.4² ≈ 4 820 m²/s²
4 Half the mass times V²KE = ½ × 64 000 × 4 820 ≈ 154 MJ
5 If the 4 main-wheel brakes took it all154 ÷ 4 ≈ 39 MJ per brake
6 Land 15 kt fast (150 kt, +11 %)KE ≈ 190 MJ: +23 % heat
Chapter 7 · Brakes, Anti-skid and Autobrake
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every aircraft brake works by friction between a fixed surface and a moving one, and its job is to convert the kinetic energy of the aircraft into heat. Kinetic energy is half m V squared, so it grows with the square of the speed. Let us work one through for an A320 landing at sixty-four tonnes and one hundred and thirty-five knots. First convert the speed to metres per second: one knot is about 0.514 metres per second, so one hundred and thirty-five knots is about 69.4 metres per second. Square it and you get about four thousand eight hundred and twenty. Multiply by half the mass, thirty-two thousand kilograms, and the kinetic energy is about 154 megajoules. If the four main-wheel brakes had to absorb all of that, each would take about thirty-nine megajoules, in well under a minute; the whole lot would bring about four hundred and sixty litres of water to the boil. Now land just fifteen knots fast, at one hundred and fifty knots. The speed is only eleven per cent higher, but the energy rises to about 190 megajoules, twenty-three per cent more heat. Watch the animation: as the aircraft slows, the kinetic energy bar drains and the same amount appears as heat in the brakes. Reverse thrust, spoilers and drag take a share of the load, but the wheel brakes still do most of the work, and runways long enough to need no brakes would be far too expensive.
Part 1 · The brake itself
Drum, single disc and multi-disc Drum brakes : shoes pressing outward on a drum; older aircraftSingle disc : a calliper squeezes one disc; enough for a light aircraft Multi-disc : a stack of plates gives a much larger braking area; used by the majority of modern transport aircraft All modern aircraft use hydraulically operated disc (plate) brakes Brake pistons are single-acting actuators: pressure applies, springs release
Chapter 7 · Brakes, Anti-skid and Autobrake
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
There have been three main kinds of aircraft brake. Drum brakes, like those on old cars, push shoes outward against a rotating drum; you will only find them on older aircraft. Today all modern aircraft use plate, or disc, brakes operated hydraulically, where fixed friction pads grip one or more rotating plates. A light aircraft needs only a single disc, squeezed by a calliper. A large aircraft needs far more braking area than one disc could ever give, so it uses a multi-disc brake: several rotating plates sandwiched between fixed plates of friction material, all squeezed together. The majority of modern transport aircraft use multi-disc brake units. One more exam point: the brake pistons are single-acting actuators. Hydraulic pressure pushes them to apply the brake, and springs, not hydraulic pressure, pull everything back when the pressure is released.
Part 1 · The brake itself
Inside a multi-disc brake Rotors are keyed to the wheel rim and turn with itStators , carrying the friction material, are keyed to the torque tube and stay stillPistons in the torque plate push the pressure plate , squeezing the stack against the thrust plate More pedal pressure, more piston force, more braking Brake torque goes to the gear leg through a torque rod (brake bar)
axle
torque tube (stators keyed here)
wheel rim (rotors keyed here)
torque rod (brake bar) to the leg
torque plate + pistons
pressure plate
thrust plate
rotors turn with wheel
stators fixed, carry the friction material
Chapter 7 · Brakes, Anti-skid and Autobrake
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look inside a multi-disc brake. The rotating plates, the rotors, have keys on their outer edge that engage slots in the wheel rim, so they turn with the wheel. Between them are the stationary plates, the stators, which carry the friction material and are keyed on their inner edge to the torque tube, fixed to the axle. At one end is the torque plate, housing a ring of actuating pistons. When you press the pedals, hydraulic pressure pushes the pistons against the pressure plate, squeezing the whole stack against the thrust plate at the far end. Watch the stack in the scene close up as the pistons apply, and open again when the pressure is released. The harder you press the pedal, the greater the force and the braking. The braking torque, trying to rotate the whole brake with the wheel, is carried to the gear leg by a torque rod, often called the brake bar.
Part 1 · The brake itself
Steel versus carbon brakes Steel brakes Carbon brakes Construction heavy steel plates with case-hardened surfaces; inorganic friction pads carbon-carbon composite rotors and stators Weight heavy much lighter : worth it on long-haul aircraftHeat absorbs and loses heat less well; fades when very hot better heat absorption and dissipation ; most efficient when hot Cost and life cheaper more expensive ; wear depends mainly on the number of applicationsTorque smooth high torque peaks: torque limiting protects the gear Danger when red hot liquid extinguishant can make hot plates shatter or explode same precaution: dry powder only
Newer steel brakes use segmented plates, many linked segments that dissipate heat better than a continuous plate.
Chapter 7 · Brakes, Anti-skid and Autobrake
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Brake plates were traditionally heavy steel, with a specially case-hardened surface, rubbing against inorganic friction pads. Two newer developments improved them. First, plates built from many interconnected segments rather than one continuous ring, which dissipate heat much better. Second, carbon. Carbon brakes absorb and dissipate heat far better than steel, and they are much lighter, which is why long-haul aircraft, where every kilogram counts for hours, use them. A carbon brake actually works best when it is hot, while a steel brake loses effectiveness as it overheats. The disadvantages are cost and, as usually taught, a shorter life; in practice carbon wear depends mainly on the number of brake applications rather than the energy. Carbon brakes can produce high torque peaks, which is why large aircraft fit torque limiting. And remember the danger with any red-hot brake: covering the plates with a liquid extinguishant can make them shatter or explode.
Part 2 · Keeping it healthy
Brake release, adjusters and wear checks Releasing the pedals: adjuster return springs pull the pressure plate back They keep a constant running clearance and compensate automatically for wear Failed return spring or wrong adjustment: brake does not release: brake drag Wear : check the indicator (retraction) pin with a gauge, brakes applied No pins: measure the gap between pressure plate and housing, brakes on Too little lining: a single disc grooves; a multi-disc overheats and erodes fast
Chapter 7 · Brakes, Anti-skid and Autobrake
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
When you release the pedals, the brake adjuster assemblies pull the pressure plate away from the stack, so the rotors and stators can separate slightly and the wheel turns freely. Each adjuster has a return spring and a friction collar on a pin. As the linings wear, the collar slides along the pin, so the plate always returns by the same small distance. That is the running clearance, kept constant automatically however much wear there has been. If a return spring fails or the unit is wrongly adjusted, the brake does not release properly, which is brake drag. The adjuster pin doubles as the wear indicator. With the brakes applied, the amount the pin sticks out of, or has disappeared into, the housing is checked with a wear gauge. If there are no pins, the gap between the back of the pressure plate and the housing is measured, again with the brakes on.
Part 2 · Keeping it healthy
Brake fade and brake drag Brake fade : the brakes are too hot to absorb more energy, so retardation fallsMost commonly from overheating during the landing run (or a high-energy stop) Brake drag : the brake does not fully release Causes of drag: faulty adjuster (return spring), wrong adjustment, air in the system , especially when hot Drag generates heat and brings on fade sooner Carbon brakes are most efficient when hot
0.1 0.2 0.3 0.4 0.5
0 200 400 600 800
steel steel fades
carbon: better when hot
brake temperature (°C)
friction coefficient
Brake fade: pads too hot to absorb more energy
Brake drag (not released) makes fade come sooner
Curves are illustrative only
Chapter 7 · Brakes, Anti-skid and Autobrake
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two faults must be kept apart. Brake fade means the brakes have become so hot that they cannot absorb any more energy, so their ability to slow the aircraft falls away. The most common cause is simply overheating, from a hard landing run, repeated heavy braking or a rejected take-off. The graph is an illustration of the difference between materials: a steel brake holds its friction at first and then fades sharply as it gets very hot, while a carbon brake grips modestly when cold and improves as it heats, so carbon brakes are most efficient when hot. Brake drag is different: the brake does not release properly after the pedals are let go. The usual causes are a faulty adjuster, for example a broken return spring, wrong adjustment, or air trapped in the brake hydraulics, which expands as the brake gets hot. A dragging brake keeps generating heat while you taxi, so it brings on brake fade much sooner than it would otherwise come.
Part 3 · Brake systems
Light aircraft brakes Toe brakes on the rudder pedals drive master cylinders ; pilot's foot force makes the pressure A small reservoir tops up the master cylinders Differential braking : left pedal, left brake; right pedal, right brake, so force differs with pedal forceUsed for steering on aircraft with a castoring nose wheel A parking brake valve traps the pressure in the brake lines
Chapter 7 · Brakes, Anti-skid and Autobrake
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a small aircraft, the pilot's feet can generate enough hydraulic pressure on their own. The top of each rudder pedal is a toe brake, which pushes the piston of a small master cylinder; a little reservoir keeps the master cylinders topped up. Each pedal has its own master cylinder and its own line, so the left pedal works the left wheel brake and the right pedal the right one. That is differential braking: the force at each wheel depends on how hard you press that pedal. Press only the left and the aircraft turns left, which is how aircraft with a freely castoring nose wheel are steered on the ground. To park, you press the pedals and close a parking brake valve, which traps the pressure in the lines to the brakes. A large aircraft is a different matter: foot power alone would never be enough, so the pressure comes from the aircraft hydraulic systems, as we will see next.
Part 3 · Brake systems
A large aircraft brake system
System 1 normal System 2 alternate
Normal metering pedals Autobrake valve selector
Alternate metering pedals
Anti-skid valves each wheel Anti-skid valves wheel pairs
Shuttle valves
brakes
accumulator
Parking brake valve: return line
anti-skid return to reservoir
auto changeover to alternate if System 1 low
Wheel speed transducers feed the anti-skid unit; torque sensors limit brake torque
The pedals only meter the pressure; the power comes from the main and standby hydraulic systems. With normal and alternate both lost, the accumulator holds parking pressure.
Chapter 7 · Brakes, Anti-skid and Autobrake
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a large aircraft the pedals only meter the pressure; the power comes from the main hydraulic systems. In this typical layout the normal brakes are powered by system one, through the normal metering valves worked by the pedals, or through the autobrake valve. From there each wheel has its own anti-skid valve, then a shuttle valve, then the brake. If system one pressure is low, the brakes switch automatically to system two, the alternate system, with its own metering valves; in alternate the anti-skid works on pairs of wheels rather than individual wheels. A brake accumulator on the normal side stores pressure. If both normal and alternate sources are lost, the accumulator maintains parking brake pressure, and it lets you use the brakes with the engines stopped, for example while towing. The parking brake valve sits in the return line from the anti-skid valves to the reservoir. Wheel speed transducers in the axles feed the anti-skid unit, and torque sensors limit excessive brake torque.
Part 4 · Anti-skid
Why a skidding wheel brakes badly Braking needs some slip between tyre and runway, but only a little Friction peaks at about 10 to 20% slip : the wheel is just about to skid A locked, skidding wheel gives much less braking and no directional control A locked tyre also wears a flat spot and can burst in seconds The pilot cannot sense when a wheel locks: hence anti-skid
Chapter 7 · Brakes, Anti-skid and Autobrake
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
To understand anti-skid, you need to know how braking friction depends on slip. A freely rolling wheel has no slip and gives no braking. As you brake, the wheel turns a little slower than the aircraft is moving, and the friction rises steeply. In this graph it peaks at about fifteen per cent slip, when the wheel is turning just a little slower than it should: the wheel is just about to skid, and that is where braking is most effective. Brake any harder and the friction falls away, until at one hundred per cent slip the wheel is locked and skidding. A skidding wheel gives much less braking, provides no cornering force, so you lose directional control, and grinds a flat spot through the tread, possibly bursting the tyre within seconds. With modern high landing speeds, heavy weights and wet runways, optimum braking really matters, and the pilot simply cannot feel when a wheel is about to lock. That is the job of anti-skid.
Part 4 · Anti-skid
How anti-skid works Controlling parameter: wheel deceleration of each wheel Datum about 18 ft/s² (6 m/s²) , more than the aircraft itself can decelerate A wheel decelerating faster is starting to skid : its brake pressure is reduced or released So pressure is reduced to the slower (skidding) wheel , never increased Mechanical units: a flywheel driven through a spring senses deceleration and opens a release valvePressure can also be held off before touchdown or during a bounce
Wheel speed Brake pressure
aircraft speed wheel dips: skid starting
released, then reapplied a little lower (adaptive bias)
Chapter 7 · Brakes, Anti-skid and Autobrake
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Anti-skid systems use the deceleration of each individual wheel as their controlling signal. The designers pick a datum, of the order of eighteen feet per second squared, or six metres per second squared, which is more than the aircraft as a whole can possibly decelerate. If a wheel slows down faster than that, it cannot be because the aircraft is stopping; the wheel must be starting to skid. So the system reduces or releases the brake pressure on that wheel, it spins up again, and the pressure is reapplied. Watch the scene: each time the wheel starts decelerating too quickly, the brake pressure is reduced, the wheel recovers, and braking resumes. Notice that anti-skid only ever reduces pressure, to the slower wheel; it never adds pressure. The first systems, from the early nineteen fifties, were mechanical: a flywheel, driven through a spring by the wheel, lags behind when the wheel decelerates suddenly, and that movement opens a valve to release the pressure.
Part 4 · Anti-skid
Electronic anti-skid Three elements: a wheel speed sensor , a control box and a servo valve Much faster cycling than a flywheel; easy to tune for each aircraft type About 15% better than mechanical, and it can be tested before use Adaptive pressure bias : after a release, pressure returns lower than before Normal brakes: each wheel individually protected; alternate: wheel pairs Torque limiting : excessive brake torque releases that brake (carbon brakes)
wheel speed transducer (in the axle)
ANTI-SKID control unit
servo valve
wheel speed
release command
from metering
to brake
also uses IRS ground speed and air/ground logic
Chapter 7 · Brakes, Anti-skid and Autobrake
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mechanical flywheel units respond slowly, and their modulation does not always match the real runway conditions. Electronic systems are faster, and their response rates and biases are easy to change in the circuitry, so the same design can be adapted to new aircraft types. An electronic anti-skid system has three elements: a wheel speed sensor, usually a transducer in the axle; a control box that computes what each wheel is doing; and a servo valve that modulates the brake pressure. It gives about fifteen per cent better braking than a mechanical unit, and it can be tested before use. A useful refinement is adaptive pressure bias: after the system has released a wheel, the pressure it reapplies is lower than the pressure that caused the skid, so it does not drive the wheel straight back into the same condition. With normal brakes each wheel is protected individually; on the alternate system, protection is by wheel pairs. Torque limiting, mainly for carbon brakes, releases any brake producing excessive torque.
Part 4 · Anti-skid
What anti-skid protects you from Touchdown protection No brake pressure before touchdown : the controller needs air/ground logic and wheel spin-up (or IRS ground speed) first.
Skid control Watches each wheel's deceleration and reduces pressure to any wheel approaching a skid.
Locked-wheel protection A wheel that locks on ice or a wet patch has its pressure fully released until it spins up again.
Take-off and landing Works on landing and on a rejected take-off , so it improves both ; essential on slush, snow, ice and wet runways.
Switched out at low speed Below about 20 mph it is deactivated (automatically or manually) so you have full control for taxying.
Inoperative? Expect longer stopping distances and use careful, progressive braking; performance penalties apply.
Chapter 7 · Brakes, Anti-skid and Autobrake
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The anti-skid unit provides three important protections. Touchdown protection stops the brakes being applied while the aircraft is still in the air: the controller watches the air and ground logic and the wheel speed, or compares wheel speed with the inertial ground speed, and only allows braking once the aircraft is on the ground and the wheels have spun up. So even if you land with your feet on the brakes, the wheels will not touch down locked. Skid control reduces the pressure to any wheel that is decelerating towards a skid. Locked-wheel protection completely releases the pressure to a wheel that has locked, for example on a patch of ice, until it spins up again. Anti-skid works for a rejected take-off as well as for landing, so it improves both, and it is vital on contaminated runways. Below about twenty miles per hour it is switched out, automatically or manually, because there is no further danger of skidding and the pilot needs full control of the brakes for taxying.
Part 5 · Autobrake
Autobrake Automatic braking on the normal brake system for landing or a rejected take-off ; not available on alternate Landing: choose one of 3 or 5 deceleration rates ; applied at touchdown with ground mode and wheel spin-up Landing settings give a set deceleration, less than maximum manual braking RTO : maximum pressure when thrust levers are closed above 85 kt ; nothing below 85 ktAnti-skid stays active; the rate can be changed without disarming Brakes to a stop or until disarmed ; normally disarmed by the crew at about 20 kt
Chapter 7 · Brakes, Anti-skid and Autobrake
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The autobrake applies the brakes automatically, using the normal brake system, during the landing roll or a rejected take-off. It is not available on the alternate system. For landing you arm it by selecting a deceleration rate; depending on the aircraft there are three or five settings. When the system senses ground mode and wheel spin-up at touchdown, it applies the brakes to hold that deceleration, with anti-skid still protecting every wheel, and you can change the rate without disarming. The landing settings give a planned deceleration, less than you could achieve with maximum manual braking. The RTO setting is different: if all thrust levers are closed above eighty-five knots on the take-off run, it applies maximum brake pressure; below eighty-five knots nothing happens. The autobrake brakes to a complete stop unless it is disarmed, which happens with any manual braking, advancing a thrust lever, stowing the speed brake lever after ground deployment, selecting disarm or off, or a system fault. Normally the crew disarm it at about twenty knots.
Part 3 · Brake systems
Parking brake and brake accumulator The parking brake handle closes a shut-off valve in the return line from the anti-skid valves Procedure: press the pedals , set the parking brake , then release the pedals Pressure is trapped in the brakes; good for overnight parking The brake accumulator lets the brakes be used with the engines stopped and holds parking pressure After a hot-brake stop do not set the parking brake: chock and let the brakes cool
accumulator
Metering pedals pressed
Anti-skid valve
brake: pressure trapped
Parking valve CLOSED
reservoir
1 press pedals 2 set parking brake 3 release pedals
return line shut: no way back
Chapter 7 · Brakes, Anti-skid and Autobrake
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
To set the parking brake on a typical large aircraft, you press the brake pedals, pull the parking brake handle, and then release the pedals. The handle works a shut-off valve in the return line from the anti-skid valves to the reservoir. With that return path closed, the pressure you applied with the pedals is trapped in the brakes, and it will hold them on for overnight parking if needed. Watch the scene: the pedals send pressure to the brake, the valve closes the return line, and the brake stays held even though the pedals are released. The brake accumulator plays a big part here. It stores pressure so that the brakes can be used when the engines are stopped, for example during towing, and if the normal and alternate supplies are both lost it is selected automatically to maintain parking brake pressure. One important exception: after a high-energy stop with hot brakes, do not set the parking brake. Chock the wheels instead and let the brakes cool.
Part 6 · Heat and fire
Brake energy and cooling time
5 10 17 20 29 35 40
60 70 80 90 100 110 120 130 140 150 160 170
50 t 60 t 70 t
DANGER (above 29) CAUTION (17 to 29) NORMAL (5 to 17)
below 5: no cooling time
brake application speed (kt)
energy per brake (million ft-lb)
Example: 23 units is in the caution zone; cooling time = (23 − 5) × 5 min = 90 minutes .
Chapter 7 · Brakes, Anti-skid and Autobrake
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Brakes, wheels and tyres can absorb only so much heat before they fail, so operators need a way of judging how much energy went into the brakes after a landing, a rejected take-off, or even a lot of taxying. That is the brake kinetic energy graph. You enter it with the aircraft weight and the speed at which braking began, then apply corrections for headwind or tailwind, the number of serviceable reversers and the airfield altitude. The answer is an energy figure, and more importantly a zone. In this example chart, below five units nothing special is needed. From five to seventeen is the normal zone, where you allow five minutes of cooling for each unit above five. Seventeen to twenty-nine is the caution zone, and above twenty-nine is the danger zone. Worked example: 23 units is in the caution zone, and the cooling time is 23 minus five, eighteen, times five minutes, which is 90 minutes.
Part 6 · Heat and fire
What to do in each brake energy zone Zone Typical actions Below 5 No cooling time and no special instructions Normal (5 to 17) Allow 5 minutes of cooling per unit above 5 before the next take-off Caution (17 to 29) Park but do not set the parking brake ; keep away from the wheels for at least 30 minutes ; before take-off check wheels, brakes and seals; allow 5 min per unit above 5 Danger (above 29) Clear the runway, alert the fire services ; minimum footbrake; no parking brake unless essential; shut down unneeded engines Danger (continued) Tyres will probably deflate (fusible plugs); approach only from front or rear ; let brakes cool without extinguishant unless on fire Brake fire Use dry powder , then retire for at least 15 minutes; allow 2 to 3 hours cooling; change wheels and tyres
Chapter 7 · Brakes, Anti-skid and Autobrake
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the actions that typically go with each zone. Below five units there is nothing special to do. In the normal zone, simply allow five minutes of cooling for every unit above five before the next take-off. In the caution zone, park the aircraft but do not set the parking brake, because clamping the hot stack together can weld it and keeps the heat in. Keep away from the wheels for at least thirty minutes, and check the wheels, brakes and seals before the next flight. In the danger zone, clear the runway and alert the fire services, use the minimum footbrake, do not use the parking brake unless it is essential, and shut down engines you do not need. The tyres will probably deflate as the fusible plugs melt; if they stay inflated, approach only from the front or rear. Let the brakes cool without extinguishant unless they are actually on fire, and then use dry powder. Afterwards the wheels and tyres must be changed.
Part 6 · Heat and fire
Brake temperature monitoring Larger aircraft have a temperature sensor in each brake Shown on the ECAM or EICAS wheel page, per wheel Above a set level: HIGH TEMP light; find the hot brake on the display Higher still: brake OVERHEAT , repeated on the central warning system Large aircraft brake indications: temperature, system pressure, anti-skid status (wear is checked on the ground with the pins)
WHEEL / BRAKE TEMPERATURE
1 2 2 1 2 6 2 1
HIGH TEMP
OVERHEAT
first level: find the brake higher level: also on the central warning system
Shown on ECAM / EICAS; numbers are a 0 to 9 scale
Chapter 7 · Brakes, Anti-skid and Autobrake
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Larger aircraft types, such as the seven forty-seven, seven seventy-seven, A three forty and A three eighty, can be fitted with brake temperature monitoring. A sensor in each brake measures its temperature, and the values are shown on the wheel page of the ECAM or EICAS display, so you can see every brake at once. Watch the scene as the brake heats up. When any brake goes above a predetermined level, a HIGH TEMP indication appears, and you use the display to find which brake or brakes are responsible. If the temperature rises further, past a second, higher level, a brake OVERHEAT warning comes on, and it is repeated on the central warning system. So overheating brakes are indicated on ECAM or EICAS, not by the gear lights or the flight instruments. Typical brake indications on a large aircraft are brake temperature, brake system pressure and anti-skid status. Brake wear is not shown in the cockpit; it is checked on the ground with the wear pins.
Part 6 · Heat and fire
Hot brakes and wheel fires Best extinguishant on a wheel or brake fire: dry powder No water or CO₂ : sudden cooling (thermal shock) can crack the plates and make the wheel explode Approach a hot wheel from the front or rear , never from the side in line with the axle Excessive braking usually ends in slow deflation as the fusible plugs melt After an overweight landing on a short runway : check brake temperatures ; park with brakes off (chocked) to cool
DANGER DANGER
approach from the front or from the rear
hot wheel
DRY POWDER if a brake is on fire
NOT water or CO₂ thermal shock: discs crack, wheel may explode
Chapter 7 · Brakes, Anti-skid and Autobrake
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
If a wheel or brake catches fire, the best extinguishant is dry powder. Never use water or carbon dioxide on red-hot brakes: the sudden cooling, a thermal shock, can crack the plates, and the wheel itself can explode. Even without a fire, a very hot wheel is dangerous, because it may burst. When a wheel bursts, fragments fly out sideways, in line with the axle, so firefighters and ground crew approach a hot wheel only from the front or the rear, never from the side. In most cases excessive braking ends more gently: the heat soaks into the wheel, the fusible plugs melt, and the tyre deflates slowly. After an overweight landing on a short runway, the first thing to check is the brake temperatures. Park the aircraft with the brakes off, wheels chocked, so the brakes can cool, rather than clamping a hot stack together with the parking brake. Keep people well clear until the temperatures have come down.
Part 6 · Heat and fire
Getting the shortest landing run Cross the threshold at the correct height and speed Deploy lift dumpers / speed brakes as early as possible: weight onto the wheels Apply full anti-skid braking as soon as possible after touchdown Use reverse thrust early, when it is most effective No need for cadence braking (pumping) with anti-skid: let the system find the limit
Chapter 7 · Brakes, Anti-skid and Autobrake
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Putting it together, how do you get the shortest landing run? Start by crossing the threshold at the correct height and speed: every extra knot adds distance, and a long flare floats you down the runway. As soon as you are on the ground, deploy the lift dumpers or speed brakes. They destroy lift and put the weight onto the wheels, which is what makes the brakes effective. Then apply full braking, with anti-skid, as early as possible after touchdown, and select reverse thrust early, because reversers are most effective at high speed. With an anti-skid system there is no need for cadence braking, the old technique of pumping the brakes to avoid locking a wheel; the anti-skid does that far faster and better than any pilot. And do not save the hard braking for the end of the run: braking lightly early and hard late is the slowest way to stop. The bars show, with illustrative numbers, how each poor habit lengthens the landing.
Part 6 · Heat and fire
Wing growth in tight turns Applies to swept-wing aircraft turning on the ground The turn centre is not the inboard main gear but a point further outboard The swept wingtip sits well aft , so it traces a larger circle than you expect Example: expected 21.7 m, actual about 24.2 m Take great care near obstructions; body gear steering reduces the problem
Chapter 7 · Brakes, Anti-skid and Autobrake
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
One last ground-handling point, wing growth. It applies only to swept-wing aircraft. When a big jet turns tightly, it does not pivot about the inside main gear. The turning centre lies on the line of the main axles, at a point further outboard, depending on the nose wheel steering angle. At the same time, the sweep puts the wingtip a long way behind the main gear. Both effects make the outer wingtip trace a bigger circle than you might expect from looking at the wingspan. In this drawing, with the turn centre about 4.6 metres from the centreline and the tip about nine metres aft of the main gear, the tip swings through a radius of about 24.2 metres instead of the 21.7 you might guess. That extra, the red band, is the wing growth. So take great care manoeuvring large swept-wing aircraft near buildings, other aircraft or any obstruction. Aircraft with body gear steering suffer less.
Summary
Brakes: what to take into the exam Brake basics KE → heat . Multi-disc : rotors on the wheel, stators on the torque tube. Single-acting pistons.
Carbon Lighter, better heat capacity, most efficient when hot ; costly. Torque limiting.
Fade and drag Fade = overheated. Drag = not released: faulty adjuster , air in the system (hot).
Wear Adjusters keep a constant clearance . Measure the pin , or plate-to-housing gap, brakes ON .
Systems Main + standby hydraulics; auto changeover. Accumulator : brakes with engines off, parking. Park valve in return line .
Anti-skid Senses wheel deceleration ; reduces pressure to the slower wheel. Touchdown, skid, locked wheel. Off below ~20 mph .
Autobrake Normal brakes only. Landing rate < max manual. RTO above 85 kt . Disarm: pedals, thrust, speed brake, selector.
Heat and fire Dry powder ; no water/CO₂. Approach fore and aft . No parking brake when hot. Temps on ECAM/EICAS .
Chapter 7 · Brakes, Anti-skid and Autobrake
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the chapter in one place. Brakes turn kinetic energy into heat; a multi-disc brake has rotors keyed to the wheel and stators keyed to the torque tube, squeezed by single-acting pistons. Carbon is lighter, absorbs more heat and works best when hot. Fade means the brakes are too hot to absorb more; drag means they are not releasing, from a faulty adjuster or air in the system. Adjusters keep a constant running clearance, and wear is checked with the pins, with the brakes on. Large aircraft brakes run on the main and standby hydraulics, with an accumulator for use with the engines off and for parking, Anti-skid senses wheel deceleration and reduces pressure to a wheel that is slowing too fast, and it is switched out below about twenty miles per hour. The autobrake uses the normal brakes, and its RTO mode fires above eighty-five knots. For fires, use dry powder, approach from the front or rear, and watch the temperatures on ECAM or EICAS.