Aircraft Systems · Chapter 8
Flight Control Systems How the pilot's hands and feet move the control surfaces: the primary controls, cable runs, rigging checks, locks and configuration warnings.
pull
elevator up
turnbuckles
fairleads
COCKPIT CONTROL TO CONTROL SURFACE
cables in pairs · pulleys · rods · stops · locks
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to flight control systems. Every time a pilot moves the column, the wheel or the pedals, something has to carry that movement, faithfully and without any slack, to a surface many metres away. In this lesson you will see which surface each control moves and in which direction, how adverse yaw arises and is cured, and how cables, pulleys, fairleads, rods and turnbuckles make up a control run. Then we look at what engineers and pilots check: cable tension, temperature, safety locking, stops, friction and backlash, control locks, the duplicate inspection, and the take-off configuration warning.
Roadmap
From the pilot's hand to the surface 1 · Primary controls Axes, surfaces and their sense. Adverse yaw, ailerons and the rudder.
2 · The control run Cables, pulleys, fairleads, rods. Reversible and irreversible systems.
3 · Rigging checks Tension, temperature, safety locking, stops, friction and backlash.
4 · Safeguards Control locks, duplicate inspection and configuration warnings.
Chapter 8 · Flight Control Systems
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First the primary flight controls: the three axes, the surface that controls each one, and the direction each surface moves when you move the column, the wheel or the pedals. We also deal with adverse aileron yaw and its cures, inboard and outboard ailerons, and the rudder ratio changer. Second, the control run itself: cables, pulleys, fairleads, push rods and sectors, and the important idea of reversible and irreversible controls. Third, the checks an engineer makes after any work on the controls: cable tension and its temperature correction, safety and locking of turnbuckles, the range of movement and the stops, friction and backlash. Finally the safeguards: control locks, the duplicate inspection, and the take-off configuration warning that protects you on the runway.
Part 1 · Moving the surfaces
Mechanical, hydraulic or electrical Mechanical : cables, rods, levers and chains connect cockpit control to surfaceHydraulic : power moves the surface; the control valve may still be worked mechanicallyElectrical (fly-by-wire): the cockpit control sends a signal ; the surface is usually still moved hydraulicallyManual primary controls are reversible : the pilot feels the air loads Fully powered controls are irreversible and need artificial feel
Mechanical
cables, rods, levers, chains
cable pair to a horn on the surface
reversible: air loads felt
Hydraulic (powered)
linkage to a control valve, jack moves surface
valve
jack
irreversible: feel is artificial
Electrical (fly-by-wire)
signal to computers, servo valve, jack
FCC
servo jack
irreversible: feel springs, computed laws
Chapter 8 · Flight Control Systems
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three ways to get a surface to move when the pilot moves a control. In a mechanical system, the cockpit control is connected directly to the surface by cables, push-pull rods, levers and chains, and the pilot's muscles do all the work. In a hydraulic system, hydraulic power moves the surface, but the pilot's input may still reach the control valve through a mechanical linkage. In an electrical, or fly-by-wire, system, moving the control produces an electrical signal; computers process it, and in practice the surface is still moved by a hydraulic jack. Keep one big distinction in mind from the start. A simple mechanical system is reversible, so the air loads come back to the pilot as feel. A fully powered system is irreversible, so the feel has to be made artificially. We return to powered controls in lesson ten.
Part 1 · Primary controls
Three axes, three primary controls Longitudinal axis : roll , by the ailerons, spoilers, or bothLateral axis : pitch , by the elevator or an all-moving tailplaneNormal axis : yaw , by the rudderAll three axes pass through the centre of gravity Controls let the aircraft be balanced (zero moments) in every configuration, then manoeuvred
Longitudinal axis: roll
ailerons (or spoilers)
Lateral axis: pitch
elevator or stabilator
Normal axis: yaw
rudder; through the CG,
at right angles to the page
All three axes pass through the centre of gravity
Chapter 8 · Flight Control Systems
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flying controls have two jobs. First, they let you balance the aircraft, with zero moments about every axis, at any speed, configuration and centre of gravity position. Second, they let you manoeuvre it. There are three axes, and all of them pass through the centre of gravity. Rotation about the longitudinal axis, nose to tail, is roll, controlled by the ailerons, by spoilers, or by both together. Rotation about the lateral axis, wing tip to wing tip, is pitch, controlled by the elevator or by an all-moving tailplane. Rotation about the normal axis, which stands vertically through the centre of gravity, is yaw, controlled by the rudder. Watch the scene: the ailerons move first, then the elevator, then the rudder. These three, ailerons, elevator and rudder, are the primary flight controls.
Part 1 · Sense of the controls
Pitch: column back, elevator up Pull the column back : elevator trailing edge goes up The tail is pushed down , so the nose pitches up Push forward: elevator down, nose down Controls are instinctive : the aircraft moves the way the hand moves Elevator travel is usually greater up than down
tail force down
nose pitches up
Column back (towards the pilot)
pull = elevator up
push = elevator down, nose down
Chapter 8 · Flight Control Systems
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the sense of each control, which you must know without thinking. Pull the control column back, towards you, and the elevator trailing edge goes up. Watch the scene. The raised elevator changes the camber of the tailplane so that it makes a downward force, the tail goes down, and the nose pitches up. Push the column forward and the opposite happens: elevator down, tail up, nose down. Bring the column back to the centre and the elevator returns to neutral. The controls are said to be instinctive: the aircraft moves in the same sense as your hand. Notice also that the elevator usually has more travel upward than downward, because more nose-up authority is needed, for example to hold the nose up in the flare with a forward centre of gravity.
Part 1 · Sense of the controls
Roll: wheel right, right aileron up Turn the wheel (or move the stick) right Right aileron up : less camber, less lift on the right wingLeft aileron down : more camber, more lift on the left wingThe aircraft rolls right The ailerons move in opposite directions , linked together
RIGHT
LEFT
less lift
more lift
rolls right
Left aileron DOWN
Right aileron UP
wheel turned right
Chapter 8 · Flight Control Systems
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Roll is controlled by the ailerons, near the wing tips. Turn the control wheel to the right, or move the stick to the right, and the right aileron goes up while the left aileron goes down. The raised right aileron reduces the camber of the right wing, so it loses lift. The lowered left aileron increases the camber of the left wing, so it gains lift. The difference in lift rolls the aircraft to the right. Watch the scene from behind: as the wheel goes right, the right aileron rises and the aircraft rolls right. When the wheel returns to neutral, the ailerons centre, but the bank remains until you roll out. A simple memory aid: the aileron goes up on the side you want to go down. Exam questions love to swap the wheel direction or mention the elevator, so read each option carefully.
Part 1 · Sense of the controls
Yaw: right pedal, rudder right Push the right pedal forward The rudder trailing edge moves right The fin makes a force to the left : the tail swings left The nose yaws right Linked by cables, rods and chains like the elevator
fin force to the left
nose yaws right
Rudder pedals
L
R
right pedal forward
= rudder right
Chapter 8 · Flight Control Systems
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Yaw is controlled by the rudder, hinged to the back of the fin. Push the right rudder pedal forward and the rudder trailing edge moves to the right. The fin now has camber, and it makes a sideways force to the left, so the tail swings left and the nose yaws to the right. Watch the scene from above: the rudder moves right and the nose follows it round. Return the pedals to neutral and the rudder centres. Again the control is instinctive: push the right foot and the nose goes right, much like steering a bicycle with your feet on the handlebars. In a light aircraft the rudder pedals are connected by cables, and often by rods and chains, in the same way as the elevator. A typical exam distractor says the right pedal moves the rudder left; do not fall for it.
Part 1 · Making a control force
Three ways to change a force, and combined surfaces Change camber A hinged surface deflected down adds camber and lift. Elevator, aileron, rudder.
Change incidence Turn the whole surface : the all-moving tail (stabilator ) for pitch.
Spoil the flow A spoiler raised on the upper surface reduces lift on one wing.
Elevons Tail-less and delta aircraft: together for pitch , opposite for roll .
Ruddervators V-tail: together for pitch , opposite for yaw .
Stabilator All-moving tailplane: both stability and pitch control in one.
Chapter 8 · Flight Control Systems
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
A control works by changing the aerodynamic force on a wing, tailplane or fin, and there are three ways to do that. You can change the camber: deflecting a hinged trailing edge surface downward increases camber and so increases lift. That is how ailerons, elevators and rudders work. You can change the incidence, turning the whole surface to a new angle of attack, which is what an all-moving tailplane, or stabilator, does for pitch. Or you can spoil the airflow, raising a panel on the upper surface to destroy lift on one wing only. Some aircraft combine two jobs in one surface. Elevons, on tail-less and delta aircraft, move together for pitch and in opposition for roll. Ruddervators, on a V-tail, move together for pitch and in opposition for yaw. The stabilator is both the horizontal stabiliser and the elevator.
Part 1 · Lateral control
Adverse aileron yaw The wing with the down aileron makes more lift, so more induced drag The other wing makes less lift and less induced drag The drag difference yaws the nose away from the roll Roll left gives a yawing moment to the right Worst at low speed and high lift coefficient
aileron down
aileron up
more induced drag
less drag
nose yaws right
Roll LEFT selected: the up-going (right) wing drags back
and the nose swings RIGHT, away from the turn
Chapter 8 · Flight Control Systems
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ailerons have an unwanted side effect called adverse yaw. When you roll, the wing with the down-going aileron makes more lift, and more lift means more induced drag. The other wing, with its aileron up, makes less lift and less induced drag. So the rising wing is held back, and the nose swings the opposite way to the roll. Watch the scene: the pilot rolls to the left, the right wing rises, and the nose swings to the right, away from the intended turn. Roll left gives yaw to the right. Adverse yaw is greatest at low speed, when the lift coefficient and the induced drag are high, and the pilot must cancel it with rudder in the same direction as the roll. Designers also build in cures, which are on the next slide.
Part 1 · Lateral control
Four cures for adverse yaw
Differential ailerons
Frise ailerons
Aileron-rudder coupling
Roll spoilers
up 25°
down 12°
up aileron moves further:
more drag on the down-going wing
UP
nose drops below the wing: high drag
DOWN
nose stays shrouded: low drag
hinge set back, asymmetric nose
wheel left
aileron run
spring link
rudder run
rudder left
rudder applied with the aileron
on the down-going wing:
less lift AND more drag
so the yaw is into the roll
no adverse yaw at all
All four put more drag on the down-going wing , the one whose aileron goes up.
Chapter 8 · Flight Control Systems
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are four main cures for adverse yaw, and they all work by adding drag to the down-going wing, the wing whose aileron goes up. First, differential ailerons: the linkage makes the up-going aileron move through a larger angle than the down-going one, say twenty five degrees up against twelve down, which adds drag on one side and reduces it on the other. Second, the Frise aileron, with its hinge set back and an asymmetric nose. When it goes up, its nose drops below the lower surface of the wing into the airflow and causes high drag. When it goes down, the nose stays shrouded. Third, aileron-rudder coupling: the two systems are interconnected, often through a spring, so rudder is applied automatically with aileron. Fourth, roll spoilers: a spoiler raised on the down-going wing cuts lift and adds drag, so there is no adverse yaw at all.
Part 1 · Large aircraft
Inboard ailerons and flaperons Tip ailerons give the biggest arm, but also the most wing twist At high speed, twist can cause loss of effect or even aileron reversal Inboard ailerons work at all speeds; outboard ones only at low speedOutboard ailerons are locked out when the flaps are retracted Flaperons : ailerons drooped with the flaps, moving differentially from there
flaps
inboard aileron
all speeds
outboard aileron
low speed (flaps out)
Right wing seen from above
Outboard: big arm, but it twists a flexible wing
at high speed and can even reverse the roll.
Chapter 8 · Flight Control Systems
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a large, fast aircraft the ailerons cause a problem. At the wing tip they have the longest arm and give the most roll for their size, but they also twist and bend the flexible wing the most. At high speed the twist can reduce the aileron's effect, or even reverse it, so the aircraft rolls the wrong way. The cure is a second set of ailerons inboard, where the wing is stiffer. Watch the scene. At slow speed, with the flaps out, both the inboard and the outboard ailerons work. When the flaps are retracted for high speed flight, the outboard ailerons are locked out and only the inboard ailerons are used. A related idea is the flaperon. Because flaps and ailerons compete for the trailing edge, the ailerons can be drooped symmetrically with the flaps to add flap area, then move differentially from that drooped position for roll.
Part 1 · Directional control
The rudder and the ratio changer Rudder: asymmetric power , crosswind take-off and landing, adverse yaw, spin recovery , propeller torque Full rudder is needed at low speed ; at high speed it could overstress the fin A rudder ratio changer reduces rudder travel for full pedal as speed rises Single-step above a set speed, or progressive with speedSide load ∝ IAS² × deflection : double IAS, quarter the travel
Rudder travel available for full pedal
100
150
200
250
300
350
0
5
10
15
20
25
30
35
indicated airspeed (kt)
max rudder (°)
7.5° at 320 kt
progressive changer
single-step
Side load ∝ IAS² × rudder angle: double the IAS,
a quarter of the travel gives the same load (illustrative values)
Chapter 8 · Flight Control Systems
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The rudder has several jobs. It keeps directional control with asymmetric power after an engine failure, it corrects for crosswind on take-off and landing, it cancels adverse yaw, it is the main control for spin recovery, and on single-engined aircraft it corrects for changes in propeller torque. Large rudder deflections are essential at low speed, for example just after an engine failure. But the air load on the rudder grows with the square of the indicated airspeed, so full rudder at high speed could overstress the fin and the rear fuselage. The answer is a rudder ratio changer, a gear change in the rudder run. A single-step changer gives less rudder for full pedal above a certain speed. A progressive one reduces it steadily as speed increases. In this illustrative graph, thirty degrees is available up to one hundred and sixty knots, but only seven and a half at three hundred and twenty.
Part 2 · The control run
Anatomy of a manual control run
Control column
on a torque tube
Turnbuckles
adjust tension
Fairleads
guide through structure
Pulleys
turn the cables
Sector (quadrant)
cable pull into rotation
Push-pull rod to the elevator horn
Cable pair: one pulls for nose up, the other for nose down
Cables carry the load in tension only; rods and tubes work in tension and compression .
Chapter 8 · Flight Control Systems
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a typical elevator control run in a light aircraft, seen from the side. The control column pivots on a torque tube near the floor. From it, a pair of cables runs aft. Each cable has a turnbuckle so its tension can be adjusted. Where the cables pass through a bulkhead or near structure, fairleads guide them and stop them rubbing. Where the run has to change direction, here to climb up into the tail, the cables pass round pulleys. At the tail the cables wrap round a sector, sometimes called a quadrant, which turns their pull into rotation, and a short push-pull rod connects the sector to the elevator horn. Bell cranks and chains over sprockets are also common, for example to turn the control wheel's rotation into cable movement for the ailerons. Remember the key difference: a cable can only pull, while a rod can push and pull.
Part 2 · The control run
Cables or push-pull rods? Cables Push-pull rods and torque tubes Weight Light : very good strength to weight ratioHeavier for the same run Routing Easy : round pulleys, through fairleadsStraight runs, bell cranks at every turn Space Takes up little volume Needs room for the rod and its travel Joints Fewer bolted joints Many joints and bearings: more wear, more backlash Damage Flexible: less prone to impact damage jamming the run A dented rod or tube can bind Action Pull only: must be fitted in pairs , kept in tension Push and pull in one member Drawbacks Stretch, wear on pulleys, tension varies with temperature No tension to set; little temperature effect
Many aircraft mix both: cables for the long runs, rods and bell cranks near the surfaces.
Chapter 8 · Flight Control Systems
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why use cables at all? Compared with push-pull rods and torque tubes, cables are light, with a very good strength to weight ratio. They are easy to route through the aircraft, because they can go round pulleys and through fairleads instead of needing straight runs and a bell crank at every corner. They take up less volume and need fewer bolted joints, so there is less to wear and less to work loose. And because they are flexible they are less prone to impact damage jamming the run, whereas a dented tube can bind. The price is that a cable can only pull, so cables must be fitted in pairs and kept in tension. They stretch, they wear where they run over pulleys, and their tension changes with temperature. Rods push and pull, need no tension, and are not much affected by temperature. Most aircraft use a mixture of both.
Part 2 · The control run
Cables in pairs, pulleys and fairleads A cable can only pull: fitting them in pairs gives positive action in both directions Tension removes backlash and allows for temperature Pulleys change the direction of a cableFairleads keep the cable straight and clear of structure ; they guide, they do not turn itPulley guards stop a slack cable jumping off
pulled: carries the load
fed out: stays taut
cockpit
surface
Pulley
changes direction
Fairlead
straight, clear of structure
Chapter 8 · Flight Control Systems
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
A cable can only pull. If the elevator were connected by a single cable, you could pull the elevator up but never push it down again. So cables are fitted in pairs, forming a closed loop, and this gives positive action in both directions. Watch the scene. When the pilot pulls, the cockpit sector turns, the upper cable is wound in and pulls the elevator sector round, while the lower cable is fed out. When the pilot pushes, the lower cable does the pulling. Both cables are kept in tension, which removes backlash, so the surface responds the moment the control moves, and the tension also allows for temperature changes. Where the run must change direction, it passes round a pulley. Where it passes through a bulkhead or close to structure, a fairlead keeps it straight and clear. A fairlead guides; it does not turn the cable.
Part 2 · Feel
Reversible and irreversible controls Reversible : force at the control moves the surface, and force on the surface moves the controlManual primary controls are reversible: air loads are felt Irreversible : surface loads cannot move the cockpit controlFully powered controls are irreversible: no natural feel , so artificial feel Power-assisted controls keep some feel; a set trim tab is irreversible
Manual: reversible
pilot force moves surface
air load moves the stick: feel
Fully powered: irreversible
valve
jack
air load stopped by the
locked fluid in the jack
So a fully powered system needs an artificial feel unit.
Power-assisted controls keep some natural feel.
A set trim tab cannot be moved by air loads: irreversible.
Chapter 8 · Flight Control Systems
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
This idea comes up again and again. A manually operated primary control is reversible. A force from the pilot moves the surface, and equally, a force on the surface, such as an air load or a gust, moves the cockpit control. That is why the pilot feels the air loads, and the feel tells you how hard you are working the aircraft. A fully powered control is irreversible. The pilot only moves a control valve, the jack does the work, and the fluid locked in the jack stops any load on the surface coming back to the column. So there is no natural feel, and it has to be added artificially, with a feel unit whose force rises with deflection and with speed. Power-assisted controls are different: the pilot still provides part of the force, so some natural feel remains. And a trim tab, once set by the trim wheel, cannot be moved by air loads: it is irreversible too.
Part 3 · Rigging checks
After any work: five checks Cable tension Set with turnbuckles , measured with a tensiometer , corrected for temperature .
Safety and locking Enough thread engaged (in safety ), then locked with wire or clips.
Range of movement Full and free travel to the stops , in the correct sense .
Friction Force to move the control, measured with a spring balance .
Backlash No free movement when the control is reversed.
Then: duplicate inspection Two qualified people check the system independently before flight.
Chapter 8 · Flight Control Systems
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
During servicing, and after any adjustment to the flying controls, the system must be checked, and in some cases the pilot takes part. There are five main checks. Cable tension: set with turnbuckles, measured with a tensiometer, and corrected for the temperature on the day. Safety and locking: each turnbuckle must have enough thread engaged to carry the load, and must then be locked so it cannot turn. Range of movement: each surface must move freely through its full travel to its stops, and, crucially, in the correct sense. More than one accident has followed controls rigged backwards. Friction: the force needed to move the control on the ground, measured with a spring balance. And backlash: there must be no free movement when the control is reversed. After all of that, a duplicate inspection by two qualified people is required before the aircraft flies.
Part 3 · Rigging checks
Setting cable tension Too slack : excessive cable movement, backlash, sloppy control Too tight : stiff controls, high friction, worn pulleys Turnbuckle : a barrel with right and left-hand threads; turning it draws both ends in or outTension is measured with a tensiometer The reading is compared with the type's rigging chart
Turnbuckle
barrel
right-hand thread
left-hand thread
inspection holes
turn the barrel: both ends draw in (or out) together
Tensiometer
anvil
anvil
riser pushes the cable a set amount sideways
the tighter the cable, the more force that takes
the dial reading converts, via a chart, to tension
Chapter 8 · Flight Control Systems
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Getting the cable tension right matters. If the tension is too low, the cables are loose, there is too much cable movement and backlash, and the control feels sloppy. If it is too high, the controls are stiff, friction is high, and the pulleys and bearings wear faster. Tension is adjusted with a turnbuckle. It has a central barrel and two end fittings, one with a right-hand thread and one with a left-hand thread, so turning the barrel draws both ends in together, or lets them both out, without twisting the cable. Tension is measured with a tensiometer. It clamps onto the cable between two anvils, and a riser pushes the cable sideways. The tighter the cable, the less it deflects, and the instrument, with its calibration chart, converts that into a tension, which is then compared with the aircraft's rigging chart.
Part 3 · Rigging checks
Temperature and cable tension Aluminium alloy expands about twice as much as steel per degree Hotter : the airframe grows more than the steel cable, so tension rises Colder : tension falls, controls may go slackAlways set tension from the chart for the ambient temperature A temperature compensator keeps tension constant automatically
Rigging chart: correct tension vs temperature
-20
-10
0
10
20
30
40
50
30
50
70
90
110
ambient temperature (°C)
cable tension (lbf)
91 lbf at 40 °C
with a temperature compensator
aluminium airframe, steel cable
Worked example: 10 m run, +30 °C
aluminium grows 6.9 mm, steel cable only 3.6 mm
the 3.3 mm difference stretches the cable: about +31 lbf
(illustrative 1/8 in cable; always use the type's own chart)
Chapter 8 · Flight Control Systems
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Cable tension changes with temperature, because the airframe and the cables are made of different metals. The airframe is aluminium alloy, which expands about twice as much per degree as the steel cable. Take a ten metre cable run that warms up by thirty degrees. The aluminium structure grows by about six point nine millimetres, but the steel cable by only three point six. The cable is stretched by the difference, and in this example the tension rises by about thirty pounds force. So on a hot day the tension is higher, and on a cold day lower, perhaps enough to make the controls slack. That is why the correct tension must always be read from the chart at the ambient temperature. Some aircraft also have a temperature compensator in the run, a spring-loaded unit that automatically keeps the tension constant as the temperature changes.
Part 3 · Rigging checks
In safety, then locked In safety : enough thread engaged to carry the cable loadCheck: the end-fitting thread must fill the inspection hole ; a pin must not pass No inspection hole: not more than three threads showing outside the barrel Then lock the turnbuckle: vibration could turn the barrel and reduce tension Usually locking wire ; also approved clips and plates
In safety: thread fills the inspection hole
pin stopped
NOT in safety: pin passes through the hole
pin passes
No inspection hole?
Not more than 3 threads showing outside the barrel
Then lock it
locking wire (or approved clips) stops vibration
turning the barrel and slackening the cable
Chapter 8 · Flight Control Systems
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once the tension is right, the turnbuckle must be checked to be in safety, which means enough thread is engaged in the barrel to carry the load. Most turnbuckle barrels have a small inspection hole at each end. To be in safety, the thread of the end fitting must completely block that hole, and this is verified by trying to push a hardened pin through it. If the pin goes in, there is not enough thread engaged. Some turnbuckles have no inspection holes; then no more than three threads of the end fitting may be visible outside the barrel. Finally, the turnbuckle must be locked, because vibration could slowly turn the barrel relative to the end fittings and let the tension fall. The usual method is locking wire, but approved locking clips and locking plates are also used.
Part 3 · Rigging checks
Range of movement: primary and secondary stops Each surface has a laid-down travel, not always equal either side of neutral Primary stop : at the surface , sets its range of movement Secondary stop : at the column or pedals With the primary stop closed, a small clearance remains at the secondary stop The secondary stop limits travel if a primary stop fails
Primary stops: at the surface
25° up
15° down
stop
stop
usually more up than down travel
Secondary stops: at the column or pedals
small clearance here when the
primary stop is already touching
a back-up if a primary stop fails;
keeps the run itself unloaded
Chapter 8 · Flight Control Systems
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The movement of each surface either side of neutral is laid down by the designer, so that there is enough control over the whole range of flight conditions. It is not necessarily the same each way: an elevator, for example, usually has more travel up than down. The limit is set by mechanical stops. A stop that limits the movement of the control surface itself is called a primary stop, and it sets the surface's range of movement. A stop that limits the movement of the control column or the rudder pedals is a secondary stop. When the system is rigged correctly and the primary stop is closed, there is still a small clearance at the secondary stop. So in normal use the primary stops take the load, and the secondary stops are a back-up that limits the travel if a primary stop fails.
Part 3 · Rigging checks
Friction and backlash Friction sets the force to move the controls on the groundIn flight air loads add to it; too much friction distorts the feel with speed Measured with a spring balance through the full travel High friction: over-tensioned cables or unlubricated bearings Backlash : free movement when direction is reversed; means worn or incorrect parts
Friction check
spring balance
pull steadily through
the full travel
High reading: cables over-tensioned
or dry, unlubricated bearings
Backlash: lost movement on reversal
control position
surface position
dead band
dead band
control moves,
surface waits:
worn pins,
loose joints
Chapter 8 · Flight Control Systems
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Friction in the control system decides how much force you need to move the controls when the aircraft is standing still. In flight, the air loads on the surfaces add to that force, and they grow with speed. The pilot judges speed and loading partly through that changing feel, so if friction is too high it swamps the air loads and the feel is distorted. Friction is measured by hooking a spring balance to the control and pulling it steadily through its full travel. Excessive friction usually means over-tensioned cables or a lack of lubrication on the bearings and pulleys. Backlash is different. It is free, ineffective movement of the cockpit control when the direction of movement is reversed: the control moves, but the surface waits. The graph shows it as a dead band. Backlash points to worn or incorrect components, such as worn pins and loose joints, and the system should be free of it.
Part 4 · Safeguards
Control locks Parked in the open, gusts could slam the surfaces against their stops: damage Control locks (gust locks): external on the surface, or internal in the cockpitCockpit locks may block the throttles , so take-off is impossible with them in Servo tab aircraft: the column still moves freely with external locks fittedSpring tab : some movement, but the controls feel very stiff
External lock (gust lock)
REMOVE
clamps the surface to the fixed structure,
with a red streamer so it cannot be missed
Internal lock in the cockpit
lock pin
lock plate blocks the throttle:
no take-off with the lock in
Chapter 8 · Flight Control Systems
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
When an aircraft is parked outside, strong or gusty winds can blow the control surfaces about and bang them against their stops with enough force to cause damage. Control locks, or gust locks, prevent this. They can be external, clamped onto the surface itself and carrying a red streamer, or internal, fitted in the cockpit to the column and pedals. A cockpit lock may be arranged so that the throttles cannot be opened while it is in place, which makes it impossible to start a take-off with the controls locked. Here is a classic trap. On an aircraft whose surfaces are moved by servo tabs, the column moves only the tab, so with external locks on the surface the cockpit controls still move freely, and a full and free check would seem fine. With a spring tab there is some movement, but the controls feel very stiff. Always remove external locks by eye.
Part 4 · Safeguards
The duplicate inspection Required whenever the control system is disturbed in any way Two separate inspections by two qualified persons , each certified Nothing disturbed between the first and second parts Checks: correct assembly, locking , full and free movement, correct sense Minor adjustment away from base: the second part may be done by a pilot licensed on type
Work on the control system
disturbed, adjusted, replaced or assembled
1st inspection
by a qualified person, who certifies it
Nothing disturbed in between
2nd part follows as soon as possible
2nd inspection
by a second qualified person, certified
Released to fly
full, free movement in the correct sense
Chapter 8 · Flight Control Systems
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the control system is so vital, the regulations require a duplicate inspection whenever it has been disturbed in any way: after assembly, overhaul, replacement, repair, adjustment or modification. The system is inspected separately by two qualified people, and each certifies the work. The two parts should be the final operations, nothing may be disturbed or re-adjusted between them, and the second part should follow the first as closely as possible. The inspectors check that every part is correctly assembled and locked, moves freely through its full range without fouling, is clean and lubricated, and works in the correct sense relative to the pilot's controls. If anything is disturbed again before flight, that part must be inspected in duplicate again. For a minor adjustment away from base, the second part of the inspection may be carried out by a pilot or flight engineer licensed on the type.
Part 4 · Safeguards
Configuration warnings Take-off configuration warning : armed on the ground when the thrust levers are advanced. Intermittent horn if:
Item Unsafe condition Why it matters Stabiliser trim Outside the take-off (green) band Too fast a rotation (tail strike) or too heavy to rotate Trailing edge flaps Not in a take-off position C L max too low: stall or runway overrun Leading edge devices Not in the take-off position Wing may stall at the rotation angle Speed brake lever Not in the down position Spoilers dump lift and add drag Doors Not fully closed and locked Door could open in flight Control locks Internal locks not fully released No control after lift-off
Cancelled only by correcting the setting. A steady horn is the landing gear warning: landing configuration with a gear leg not down and locked (triggered by flap and thrust lever position).
Chapter 8 · Flight Control Systems
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
The final safeguard is the take-off configuration warning. It is armed when the aircraft is on the ground and the thrust levers are advanced for take-off. If any of these items is wrong, an intermittent warning sounds: the stabiliser trim outside the safe band, the trailing edge flaps or the leading edge devices not in a take-off position, the speed brake lever not down, any door not fully locked, or, on aircraft with internal control locks, the flight controls not fully unlocked. The warning can only be cancelled by correcting the setting. Do not confuse it with the landing gear warning. That one is a steady horn, which sounds when the aircraft is in the landing configuration and any landing gear is not down and locked. It is triggered by the flap position and by the thrust levers being closed. Intermittent on take-off, steady for the gear.
Summary
What to take into the exam Sense Column back: elevator up. Wheel right: right aileron up. Right pedal: rudder right.
Adverse yaw Down aileron = more induced drag. Cures: differential, Frise, coupling, spoilers.
Large jets Outboard ailerons locked out with flaps up. Ratio changer cuts rudder at speed.
Cables Pull only, so in pairs. Pulleys turn, fairleads guide. Light, easy to route.
Feel Manual: reversible. Fully powered: irreversible, needs artificial feel.
Tension Turnbuckle and tensiometer. Hot day: higher tension (aluminium grows more).
Checks In safety (pin test, 3 threads), locked. Primary stop at surface, secondary at column.
Safeguards Gust locks (servo tab trap). Duplicate inspection. T/O warning intermittent.
Chapter 8 · Flight Control Systems
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. Column back, elevator up, nose up. Wheel right, right aileron up, left aileron down, roll right. Right pedal forward, rudder right, nose right. Adverse yaw comes from the extra induced drag of the wing with the down-going aileron, and it is cured by differential ailerons, Frise ailerons, aileron-rudder coupling and roll spoilers. On large jets the outboard ailerons are locked out when the flaps are up, and a rudder ratio changer reduces rudder travel at high speed. Cables can only pull, so they are fitted in pairs; pulleys change their direction and fairleads keep them straight. Manual controls are reversible; fully powered controls are irreversible and need artificial feel. Tension rises on a hot day. Turnbuckles must be in safety and locked. Primary stops are at the surface, secondary stops at the cockpit control. And remember the gust lock trap, the duplicate inspection, and the intermittent take-off warning.