Aircraft Systems · Chapter 22
Fuel Systems and Refuelling Tanks, pumps and valves from the light single to the airliner, how fuel is measured, and how to refuel safely.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to fuel systems and refuelling. In the last lesson we studied the fuel itself. Now we follow it through the aircraft: where it is stored, how pumps and valves deliver it to the engines in every attitude, how the crew moves it around for balance or dumps it in an emergency, and how its quantity is measured so precisely that the gauges are trusted for every flight plan. We finish on the ground, with refuelling: the safety zones, static bonding, the rules for refuelling with passengers on board, and the special hazards. Many exam questions come straight from this lesson, so we will pick out the traps as we go.
Roadmap
What this lesson covers A fuel system must store fuel and deliver more than the engines can ever use , in every attitude and at every altitude, and let the crew manage and measure it.
1 · Storage Integral, rigid and flexible tanks , baffles, vents and drains.
2 · Delivery Light-aircraft systems, booster pumps , cross-feed, the twin-jet layout, the engine fuel system, transfer and jettison .
3 · Measurement Capacitance gauging, failures, dripsticks and the cockpit fuel page.
4 · Refuelling Zones , pressure refuelling, bonding , passengers on board and special hazards.
Chapter 22 · Fuel Systems and Refuelling
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the fuel systems lesson. A fuel system has one overriding job: to store fuel and deliver more of it than the engines can ever use, in every attitude and at every altitude, so that an engine is never starved. Around that job sit all the things the crew needs: ways to feed any engine from any tank, to isolate a fire, to move fuel for balance, to dump it in an emergency, and to know exactly how much is left. We will work in four parts. First, storage: the types of tank and what is built into them. Second, delivery: from the simple light aircraft system to booster pumps, cross-feed, the twin-jet layout, the engine fuel system, transfer and jettison. Third, measurement: capacitance gauging and its failure modes. And fourth, refuelling, with all the safety precautions the exam loves.
Part 1 · Storage
Three kinds of fuel tank
sealed wing box
metal tank on mounts
rubberised bag, laced in
Integral tanks The wing box (and on some types the centre section and stabiliser) is sealed during manufacture . Very little extra weight; used on all large transport aircraft .
Rigid tanks A separate sealed metal (or composite) container in the wing or fuselage, or external, e.g. at the wing tip. Simple, but adds weight and needs mountings; common on light aircraft .
Flexible tanks Bags of rubberised fabric (bladders) supported by the surrounding structure. Popular in military aircraft, as they can be made self-sealing .
Chapter 22 · Fuel Systems and Refuelling
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel is carried in three kinds of tank. An integral tank is not a separate container at all: the wing box, made of the spars and skins, is sealed during manufacture so that the structure itself holds the fuel. On some types the centre section and even the horizontal stabiliser are used the same way. Because the structure is already there, an integral tank adds almost no weight, which is why every large transport aircraft uses them. A rigid tank is a separate sealed container, usually metal, mounted in the wing or fuselage, or outside, for example on a wing tip. It is simple but heavier, and needs mountings, so it is popular on light aircraft. A flexible tank is a bag of rubberised fabric, sometimes called a bladder, laced into a cavity and supported by the structure around it. Military aircraft like them because they can be made self-sealing after battle damage.
Part 1 · Storage
Where an airliner carries its fuel
wing tanks (inner + outer) centre tank trim tank
Integral tanks: wings (often split into inner and outer cells), the centre wing box and, on larger types, a trim tank in the stabiliser.
Chapter 22 · Fuel Systems and Refuelling
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is where a modern airliner carries its fuel, shown on the A three twenty with its skin made see-through. Most of it sits in the wing tanks, which are integral tanks between the front and rear spars. On many types each wing tank is split into an inner and an outer cell, and we will see shortly why that matters. In the middle is the centre tank, in the wing centre box that passes through the fuselage between the two wings. Larger long-range types add a tank in the horizontal stabiliser, the trim tank. It increases capacity, but more importantly, moving fuel into and out of it shifts the centre of gravity, so it can be used to trim the aircraft for less drag. Some types also carry extra tanks in the cargo hold or the fin.
Part 1 · Storage
Inside the tank: baffles and check valves Baffles (the wing ribs) dampen surging of fuel during manoeuvres, acceleration, deceleration and sideslip Without them, large inertial loads and sudden shifts of fuel and CG would occur, and pumps could be uncovered Baffle check valves : flap valves that let fuel flow inboard , towards the pumps, but not outboard Each tank also has vents , water drains at the lowest point, feed pipes, gauging probes and a filler Large aircraft add booster pumps , high and low level switches , refuel valves and filters
fuel may flow inboard, towards the pumps
← root tip → baffle ribs
flap check valves open inboard only
Chapter 22 · Fuel Systems and Refuelling
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Inside an integral wing tank the fuel is divided up by the wing ribs, which act as baffles. Their job is to dampen surging and sloshing. Without them, in a manoeuvre, a hard acceleration or deceleration, or a sideslip, the whole mass of fuel would rush from one end of the tank to the other, putting big inertial loads on the structure, shifting the centre of gravity, and possibly uncovering the pumps. Some large aircraft fit baffle check valves: simple flap valves at the bottom of the ribs that swing open to let fuel flow inboard, towards the pumps at the root, but close to stop it running outboard towards the wing tip. Each tank also has vents, water drains at its lowest point, feed pipes, gauging probes and a filler. Large aircraft add booster pumps, high and low level switches, refuel valves and filters.
Part 1 · Storage
The vent system Vents keep the air pressure above the fuel equal to ambient , so tanks do not collapse as fuel is used or burst when refuelled A ram-air intake can slightly pressurise the tanks in flight: helps fuel flow and reduces boiling A vent surge tank near the tip collects any fuel that overflows into the vents and returns it to the main tanks Tanks keep an expansion space of 2% of tank volume (certification requirement) An overpressure relief valve protects the tank structure if the vents block or refuelling overfills
vent gallery (air)
2% expansion space above the fuel
ram-air vent scoop
slight tank pressure in flight
overflow drains back
relief valve
main wing tank surge tank
(at the tip)
Chapter 22 · Fuel Systems and Refuelling
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A tank must breathe. As fuel is burnt, air has to come in to replace it, or the tank would be sucked inwards; as fuel is pumped in during refuelling, air has to get out, or the tank would burst. The vent system does this, keeping the pressure above the fuel equal to the outside pressure. Many systems use a ram-air vent scoop under the wing, which slightly pressurises the tanks in flight. That small positive pressure helps the fuel flow to the pumps and reduces boiling at altitude. Any fuel that slops into the vent gallery is caught in a vent surge tank, usually near the wing tip, and drained back into the main tank. The certification rules require an expansion space of two per cent of the tank volume, and an overpressure relief valve protects the structure if a vent blocks or a refuelling valve fails to close.
Part 2 · Delivery
A single-engine light aircraft fuel system
LEFT wing tank RIGHT wing tank
rigid tank, overwing filler rigid tank, overwing filler
vent vent cap cap
drain drain
L R BOTH OFF
tank selector
strainer
drain
electric pump
start, take-off, landing,
engine pump failure
EDP
engine-driven pump
carburettor
ENGINE
primer
primer squirts fuel into the inlet manifold
L contents R contents fuel pressure
High-wing types may feed by gravity ; low-wing types need an engine-driven pump with an electric pump as back-up. Drain the tank sumps and strainer before flight .
Chapter 22 · Fuel Systems and Refuelling
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a typical single-engine light aircraft fuel system. Two rigid tanks in the wings are filled through caps on top, the overwing method. Each has a vent and a drain at its lowest point. The tanks feed a selector valve, which the pilot sets to left, right, both or off. From there the fuel passes through a strainer, a filter bowl with its own drain, and then through an electric pump and an engine-driven pump to the carburettor. The electric pump is used for starting, take-off and landing, and as a back-up if the engine-driven pump fails. A priming pump takes fuel from the strainer housing and squirts it into the inlet manifold to help a cold start. The pilot monitors contents gauges for each tank and a fuel pressure gauge. On many high-wing types gravity alone pushes the fuel to the engine.
Part 2 · Delivery
Booster pumps and the collector box Booster pumps : normally two per tank , centrifugal , driven by electric (AC) motors: low pressure (20–40 psi), high flow They push fuel to the engine, preventing cavitation of the engine-driven pump and vapour lock at altitude Also used to transfer fuel between tanks and to jettison it Mounted in a collector box (feeder box) that always holds fuel (typically about 500 kg), so the pumps stay submerged in any attitude If both pumps in a tank fail, the engine pump can still draw fuel through a suction bypass valve , but the MEL usually imposes a maximum altitude
tank collector box flap valve pump to engine
centrifugal · AC motor · 20–40 psi
Chapter 22 · Fuel Systems and Refuelling
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a large aircraft the fuel is pushed to the engines by booster pumps inside the tanks, normally two per tank for redundancy. They are centrifugal pumps, driven by electric AC motors, giving a low pressure, about twenty to forty psi, but a high flow. Pushing the fuel keeps the line to the engine above its vapour pressure, so the engine-driven pump does not cavitate and vapour lock cannot form at altitude. The same pumps are used to transfer fuel between tanks and to jettison it. The pumps sit in a collector box, also called a feeder box, at the bottom of the tank. Flap valves let fuel in but not out, so the box always holds a reserve, typically around five hundred kilograms, and the pumps stay covered whatever the attitude. If both pumps in a tank fail, the engine pump can still suck fuel through a suction bypass valve, but the minimum equipment list usually limits the maximum altitude.
Part 2 · Delivery
A twin-jet fuel system
No. 1 tank (left wing) Centre tank No. 2 tank (right wing)
ENGINE 1 ENGINE 2
engine fuel shut-off valve
engine fuel shut-off valve
cross-feed valve (shut)
APU
APU feed
suction bypass suction bypass
scavenge jet pump: residual centre fuel to No. 1 tank
2 booster pumps 2 booster pumps 2 booster pumps
Normally tank to engine (No. 1 to engine 1, No. 2 to engine 2), cross-feed shut. The APU draws from the No. 1 side; a scavenge jet pump moves the last centre-tank fuel into No. 1 tank.
Chapter 22 · Fuel Systems and Refuelling
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
This schematic shows a typical twin-jet system. There are three tanks: number one in the left wing, the centre tank, and number two in the right wing, each with two booster pumps. In normal operation it is tank to engine: number one tank feeds engine one and number two tank feeds engine two, with the cross-feed valve between the two feed lines shut. Each engine has a fuel shut-off valve in its feed. The APU takes its fuel from the number one side; with no booster pumps running, it draws through a bypass, but it can be fed from any tank whose pumps are on. When the centre tank pumps can no longer pick up fuel, a scavenge jet pump moves the last of it into number one tank. Suction bypass valves in the wing tanks let the engine pumps draw fuel if both boosters in a tank fail. A temperature sensor in number one tank feeds a cockpit indication.
Part 2 · Delivery
Which tank first? Centre, then wings After take-off, centre tank fuel is used first , then the wing tanks Fuel in the wings relieves wing bending : it hangs where the lift is generated In split wing tanks the outer cells are kept full until the inner cells reach a set level Fuel kept outboard also damps flutter On many types the centre pumps override the wing pumps automatically (higher delivery pressure)
lift along the span fuel weight in the wing
order of use: centre → inner wing → outer wing
Chapter 22 · Fuel Systems and Refuelling
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Which tank is used first? After take-off the centre tank fuel is used first, then the wing tanks. The reason is structural. Lift acts all along the wings and bends them upwards about the root. Fuel inside the wing hangs right where the lift is produced, so its weight bends the wing the other way and relieves the bending at the root. Fuel in the centre tank gives no such relief. So we empty the centre first, watch it go, and only then feed from the wings. The same logic explains split wing tanks: the outer cells are kept full until the inner cells have dropped to a set level, keeping weight outboard for longest. Fuel kept outboard also helps to damp flutter. On many aircraft this sequence happens automatically, because the centre tank pumps deliver at a higher pressure and override the wing pumps until the centre tank is empty.
Part 2 · Delivery
The cross-feed valve The cross-feed valve lets fuel go from any tank to any engine Open it to feed both engines from one tank , or one engine from both sides Uses: correcting a fuel imbalance , feeding after a pump failure, single-engine operation Indicated by a switch with a valve-position light or on the fuel synoptic page It is not for isolating an engine in a fire: that is the engine fuel shut-off valve
ENG 1 ENG 2
left tank right tank: pumps OFF cross-feed OPEN
Chapter 22 · Fuel Systems and Refuelling
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The cross-feed valve connects the two engine feed lines, so fuel can go from any tank to any engine. With it open you can feed both engines from one tank, or one engine from both sides. Here it is open, and the left tank is feeding both engines while the right tank pumps are switched off. You would do this to correct a fuel imbalance, to keep feeding an engine whose own tank pumps have failed, or in single-engine flight to use fuel from the dead engine's side. The valve has a cockpit switch with a position light, or appears on the fuel synoptic page. One exam trap: the cross-feed is not the valve that isolates an engine in a fire. That job belongs to the engine fuel shut-off valve, closed by the fire handle.
Part 2 · Delivery
Worked example: correcting an imbalance Left tank 5 200 kg , right tank 4 000 kg ; each engine burns 1 200 kg/h 1 · Open the cross-feed 2 · Switch off the pumps in the tank with less fuel (right): the left tank now feeds both engines at 2 400 kg/h 3 · Imbalance 1 200 kg ÷ 2 400 kg/h = 30 minutes 4 · When balanced, pumps back on, cross-feed shut : tank to engine again
2 000
3 000
4 000
5 000
6 000
0
15
30
45
60
75
90
balanced: 4 000 / 4 000 kg
left tank
right tank
cross-feed open
normal feed restored
minutes after opening the cross-feed
tank contents (kg)
each engine burns 1 200 kg/h; imbalance 1 200 kg ÷ 2 400 kg/h = 30 min
Chapter 22 · Fuel Systems and Refuelling
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us work through an imbalance. The left tank holds five thousand two hundred kilograms, the right tank four thousand, and each engine burns twelve hundred kilograms an hour. The fix uses the cross-feed. First, open the cross-feed valve. Second, switch off the booster pumps in the tank with less fuel, here the right tank. Now the left tank feeds both engines, so it drains at twenty-four hundred kilograms an hour while the right tank stays put. The difference is twelve hundred kilograms, so it takes twelve hundred divided by twenty-four hundred, which is half an hour, to balance. After thirty minutes both tanks read four thousand. Then switch the right pumps back on and close the cross-feed, restoring tank to engine feed. A common mistake is to switch off the pumps in the fuller tank, which makes the imbalance worse.
Part 2 · Delivery
From the tank to the burners LP shut-off valve (spar or firewall valve) at the boundary: closed by the fire handle , on some types also by the fuel control switchThe engine-driven LP pump backs up the boosters: after a double booster failure it sucks fuel from the tank Fuel is warmed (FCOC and heater), then cleaned by the LP filter ; a blocked filter bypasses and lights a warning The HP pump and fuel control unit meter fuel to the burners; the HP shut-off valve is the normal way to stop the engine The flowmeter , between the HP shut-off valve and the nozzles, gives fuel flow and fuel used
tank
Booster pumps (airframe, electric)
LP shut-off (spar) valve : fire handle
LP pump : engine-driven, backs up boosters
FCOC : fuel heated, oil cooled
Fuel heater : compressor air
LP filter + bypass, bypass light
HP pump : engine-driven
FCU Fuel control unit : meters fuel
HP shut-off , then flowmeter
Burners (fuel nozzles)
airframe engine
Chapter 22 · Fuel Systems and Refuelling
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the fuel from the tank to the burners. Leaving the tank, it passes the low-pressure shut-off valve, often called the spar valve or firewall valve, at the boundary between airframe and engine. That is the valve the fire handle closes; on some types the fuel control switch also operates it during normal start and shutdown. Next is the engine-driven low-pressure pump. Normally the boosters feed it, but after a double booster failure in a tank it sucks fuel from the tank on its own. The fuel is then warmed, first in the fuel-cooled oil cooler and then in the heater, and cleaned by the low-pressure filter, which has a bypass and a cockpit light if it blocks. The high-pressure pump and the fuel control unit meter the fuel. The high-pressure shut-off valve is the normal way to stop the engine, and the flowmeter, between that valve and the nozzles, measures fuel flow and fuel used.
Part 2 · Delivery
Larger aircraft: transfer and trim Multi-engine systems add transfer galleries and transfer pumps to move fuel between tanks A stabiliser (trim) tank adds capacity and lets fuel be moved to set the CG : an aft CG means less trim drag Stabiliser and centre fuel are used first, then the wings; outboard fuel is kept longest Fuel pipes through the pressurised fuselage are double-walled , so a leak cannot fill the cabin with fumes A fuel management computer does most of the monitoring and switching on modern two-pilot types
centre tank trim tank double-walled pipe
CG moves aft
Chapter 22 · Fuel Systems and Refuelling
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Larger aircraft add more tanks, so they need ways to move fuel around. Transfer pumps and transfer galleries carry fuel from one tank to another. On long-range types a tank in the horizontal stabiliser, the trim tank, adds capacity and, more cleverly, lets the crew or the computer move fuel aft in the cruise. That moves the centre of gravity aft, the tailplane needs less download, and trim drag falls, saving fuel. The stabiliser and centre tank fuel is used first, and as in the twin, fuel is kept in the outer wing for as long as possible. Wherever a fuel pipe passes through the pressurised fuselage, it is double-walled, so that a leak cannot fill the cabin with fumes. On older types a flight engineer managed all this by hand; on modern two-pilot aircraft a fuel management computer does almost all the monitoring and switching.
Part 2 · Delivery
Fuel jettison Needed when the maximum landing mass is well below the maximum take-off mass , and an early return would mean landing too heavy Booster or jettison pumps push fuel out through jettison nozzles near the wing tips, at the trailing edge , well clear of the aircraft The crew can preselect the fuel to remain; jettison stops automatically at that figure Low-level float switches stop jettison before the main tanks run too lowRule: after jettison there must be enough fuel to climb to 10 000 ft and cruise for 45 minutes at maximum-range speed
jettison nozzle low-level float switch jettison pipe
remaining fuel: climb to 10 000 ft + 45 min at max-range speed
Chapter 22 · Fuel Systems and Refuelling
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some aircraft can jettison, or dump, fuel. It is needed when the maximum landing mass is much lower than the maximum take-off mass, so that an emergency return soon after take-off would mean landing too heavy for the structure, or the aircraft could not meet the climb requirements for a go-around. Booster or dedicated jettison pumps push fuel out through jettison nozzles, typically one on each wing near the tip at the trailing edge, well clear so that the fuel cannot re-enter the aircraft. The crew can usually preselect the fuel to remain, and jettison stops automatically when that figure is reached. As a final safeguard, low-level float switches in the main tanks stop jettison before they run too low. The certification rule is that the fuel remaining must be enough to climb to ten thousand feet and then cruise for forty-five minutes at maximum-range speed.
Part 3 · Measurement
Measuring fuel by capacitance Float and resistance gauges measure volume : simple, light aircraft; suffer manoeuvre error ; cannot correct for densityCapacitance probes measure mass : no manoeuvre error, compensated for density : essential on transport aircraftEach probe is two concentric tubes fed with AC ; the dielectric between them is fuel and air Fuel has a higher dielectric constant than air, so more fuel = more capacitance = more current A compensator probe, always covered, measures the dielectric (density) of the fuel Many probes in parallel average out the effect of attitude
gauge in kg
probes in parallel compensator
Chapter 22 · Fuel Systems and Refuelling
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two ways to measure fuel quantity. A float moving a variable resistance measures the volume. It is simple and suits light aircraft, but it suffers manoeuvre errors as the fuel sloshes, and it cannot correct for density. Transport aircraft use capacitance gauging, which measures mass. Each probe is a capacitor made of two concentric tubes, supplied with alternating current. The voltage, frequency and plate size are fixed; the only variable is the dielectric between the tubes, which is partly fuel and partly air. Fuel has about twice the dielectric constant of air, so as the fuel level falls, as you see here as it is burnt, the capacitance and the current fall with it, and the gauge reads less. A compensator probe at the very bottom, always covered, measures the dielectric of the fuel itself, which tracks its density, so the system shows true mass. Many probes connected in parallel average out the aircraft attitude.
Part 3 · Measurement
Capacitance gauging: failures and quirks Power failure or a circuit fault: a fail-safe circuit drives the pointer slowly to empty (full scale low), never showing more fuel than there isA test switch uses the same circuit: the needle moves towards empty and returns when released A tank full of water reads full scale high : water's dielectric constant (about 80) is far above fuel's Fuel warms and expands by 10% : a compensated gauge in kg shows the same mass Microbial growth or water on the probes can upset the reading
Dielectric constant (log scale)
1
10
100
Air
1
Jet A-1
≈ 2.1
Water
≈ 80
E F Power failure drifts slowly to empty
E F Water in tank full scale high
E F Fuel warms same mass shown
Chapter 22 · Fuel Systems and Refuelling
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The exam asks several questions about how capacitance gauges fail. If the power fails, or the circuit develops a fault, a fail-safe circuit drives the pointer slowly towards empty. The design idea is that the gauge must never show more fuel than you actually have, and a slowly falling needle catches your attention. So the answer to a power failure question is full scale low. Many systems have a test switch that uses the same circuit: press it and the needle runs towards empty, release it and it returns. Now a classic trick: what if a tank were filled with water? Water has a dielectric constant of about eighty, against about two for fuel, so the gauge would read full scale high. Finally, if the fuel warms and expands by ten per cent, a compensated gauge reading in kilograms shows exactly the same, because the mass has not changed.
Part 3 · Measurement
Backups: dipsticks, dripsticks and magnetic level indicators If the gauging fails, the quantity must still be found before flight Dipstick : from the top of the tank; simple but means working on a high, slippery wingDripstick : a calibrated hollow tube drawn down from under the wing ; fuel drips out when its top passes the fuel levelMagnetic level indicator (dropstick): a float with a magnet rides on the fuel; a calibrated rod is lowered until its magnet latches to the floatThe reading gives the level ; tables and the fuel density convert it to mass
float with magnet calibrated rod read below the wing sealed tube
level × tank tables × density = mass
Chapter 22 · Fuel Systems and Refuelling
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the electronic gauging fails, you still need to know how much fuel is on board. The oldest method is a dipstick through the top of the tank, which works but means walking on a high, slippery wing. A dripstick is a calibrated hollow tube pulled down from the underside of the wing through a fuel-tight seal. When its open top passes below the fuel level, fuel starts to drip out of it, hence the name, and you read the level off the tube; the drawback is a sleeve soaked in fuel. The neater version is the magnetic level indicator, or dropstick. A float carrying a magnet rides on the fuel around a sealed tube. You lower a calibrated rod inside the tube until the magnet at its tip latches onto the float, and read the length that shows below the wing. The level, with the tank tables and the fuel density, gives the mass.
Part 3 · Measurement
Fuel indications in the cockpit Light aircraft: contents gauges and a fuel pressure gauge Transport aircraft add: fuel on board , fuel used per engine, quantity per tank and fuel temperature Valve positions : engine shut-off, cross-feed, APU, transferPump status and low-pressure warnings; filter bypass indicationShown on mimic diagrams with dolls' eyes, or on electronic synoptic pages (Airbus ECAM, Boeing EICAS)
FUEL FOB
14 020 kg
F.USED 1 2 860
F.USED 2 2 860
ENG 1 valve ENG 2 valve X-FEED APU (shut)
L OUTER L INNER CTR R INNER R OUTER
690 5 120 2 400 5 120 690
−18 °C −17 °C
green: open / running · amber: shut / off valve bar in line with the pipe = open centre pumps off here: centre fuel already used first, wing feeding
Chapter 22 · Fuel Systems and Refuelling
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
What does the crew see? A light aircraft has contents gauges and a fuel pressure gauge. A transport aircraft needs much more: the total fuel on board, the fuel used by each engine, the quantity in every tank, and the fuel temperature. It also shows the position of every important valve, the engine shut-off valves, the cross-feed, the APU valve and the transfer valves, whether each pump is running, low-pressure warnings, and a filter bypass indication if a low-pressure filter is blocking. Older aircraft showed this on the flight engineer's panel as a mimic diagram with little dolls' eye indicators. Modern aircraft use an electronic synoptic page like this one, on the Airbus ECAM or the Boeing EICAS. Notice the centre tank pumps shown off here: the centre fuel has been used first, and the wings are now feeding.
Part 4 · Refuelling
The fuelling zone The fuelling zone extends at least 6 m (20 ft) round the filling and venting points and the fuelling equipment Inside it: no smoking ; only authorised people and vehicles, as few as possible An APU whose exhaust blows into the zone must be started before caps are removed or hoses connected; if it stops, do not restart until fuelling is over GPUs as far away as practical; never connected or disconnected during fuellingFire extinguishers readily accessible
GPU
well clear
6 m
vent
vent
refuel point
bowser
Zones: at least 6 m (20 ft) round filling and vent points and the equipment
drawn to scale: 34 m span, 37 m length
Chapter 22 · Fuel Systems and Refuelling
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before fuelling begins, fuelling zones are set up. A zone extends at least six metres, or twenty feet, around the filling points, the vent outlets and the fuelling equipment itself, as you see drawn to scale here. Inside the zones there is no smoking, and only authorised people and vehicles may enter, as few as possible. The APU rule is a favourite exam question. If the APU is needed and its exhaust discharges into the zone, it must be started before the filler caps are removed or the fuelling connections are made, and it may then run throughout. If it stops for any reason during fuelling, it must not be restarted until fuelling has finished and there is no danger of igniting vapour. Ground power units should be placed as far away as practical, and must not be connected or disconnected while fuelling is in progress. Fire extinguishers must be readily accessible.
Part 4 · Refuelling
Overwing and pressure refuelling Overwing : an open nozzle through a filler cap; light aircraft; quantity shown on the vehicle in litres or gallonsPressure refuelling : from a hydrant or bowser through an underwing coupling and a refuel galleryQuantity, tanks and valves are selected at a refuel control panel ; the required load is preselected A high-level sensor in each tank closes its refuel valve when full: tanks cannot be overfilled The same coupling is used for defuelling ; defuelled fuel may not be reused until its quality is verified
high-level sensor
underwing coupling refuel valve refuel gallery
full tank → sensor → refuel valve closes
Chapter 22 · Fuel Systems and Refuelling
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Light aircraft are refuelled overwing, with an open nozzle through the filler cap, and the quantity delivered is shown on the vehicle in litres or gallons. Large aircraft are pressure refuelled. A hose from a hydrant dispenser or a bowser connects to an underwing coupling, and fuel flows through a refuel gallery and a refuel valve into each tank, from the bottom, as you see here as the tank fills. The operator works from a refuel control panel, where the total load is preselected and the tanks and valves are controlled. Near the top of each tank is a high-level sensor. When the fuel reaches it, the sensor lights up, the refuel valve closes, and the flow stops, so no tank can be overfilled. The same coupling is used to defuel. Note one exam point: defuelled fuel must not be used again until its quality has been verified.
Part 4 · Refuelling
The refuelling control panel Quantity per tank, the preselected total and the actual fuel on boardHigh-level lights (blue): a tank is full and its refuel valve has closed automaticallyMode select (guarded OFF): OFF, REFUEL, DEFUEL; refuel valve switches: NORM (automatic), OPEN, SHUTEND light (green) when automatic refuelling is complete; TRF light (amber) when the transfer valve is openTest of the high-level sensors and lights; power from GPU, APU or battery The sequence of filling tanks can move the CG : follow the aircraft manual
LEFT CTR RIGHT
HI LVL HI LVL HI LVL
6.30 3.20 6.30
QTY ×1000 kg QTY ×1000 kg QTY ×1000 kg
REFUEL VALVE REFUEL VALVE REFUEL VALVE
OPEN NORM SHUT OPEN NORM SHUT OPEN NORM SHUT
MODE SELECT
REFUEL
OFF DEFUEL
guarded at OFF
PRESELECTED ACTUAL
15.8 15.8
− +
END
AUTO REFUEL
TRF
transfer valve open
TEST: HI LVL / LIGHTS POWER: GPU · APU · BATTERY
blue HI LVL: tank full, its refuel valve closes automatically
Chapter 22 · Fuel Systems and Refuelling
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a typical external refuelling control panel, drawn in the style of an Airbus panel. Along the top are the quantity displays for each tank, with a blue high-level light above each one. When a light comes on, that tank is full and its refuel valve has closed by itself. Below are the refuel valve switches: normally guarded in NORM, where the automatic logic controls them, with OPEN and SHUT for manual control. The mode selector, guarded at OFF, chooses REFUEL or DEFUEL. The operator sets the required total on the preselected display with a rocker switch, and watches the actual figure climb. A green END light shows that automatic refuelling is complete, and an amber transfer light shows the transfer valve is open, as in defuelling. A test switch checks the high-level sensors and the lights. Remember too that the order in which tanks are filled can move the centre of gravity.
Part 4 · Refuelling
Bonding: beating static electricity Fuel flowing through hoses and filters generates static charge ; a spark in vapour can ignite it Before fuelling, bond the aircraft to the fuelling equipment with dedicated wires and clips ; never rely on conductive hoses Overwing : bond the nozzle to the aircraft before the filler cap is removed ; funnels, filters and cans are bonded too; no plastic funnels Pressure refuelling: the metal-to-metal contact of nozzle and coupling makes a separate hose-end bond unnecessaryBonding wires stay connected until the caps are refitted or the pressure hose disconnected
JET A-1
bonding wire: first on, last off
nozzle bonded before the cap is opened
1 · bond aircraft to equipment
2 · overwing: bond nozzle, then open the cap
3 · fuel
4 · refit caps or disconnect the pressure hose
5 · only then remove the bonding wires
Chapter 22 · Fuel Systems and Refuelling
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel rushing through hoses and filters generates static electricity, and a spark in fuel vapour can start a fire. The defence is bonding, which simply means connecting things together electrically so that no difference in charge can build up. Before fuelling, the aircraft is bonded to the fuelling equipment with dedicated wires and clips. Do not rely on a conductive hose for this. For overwing fuelling, the nozzle is bonded to the aircraft structure before the filler cap is removed, and the same goes for any funnels, filters or cans; plastic funnels must never be used. For underwing pressure refuelling, the metal-to-metal contact between the nozzle and the aircraft coupling does the job, so no separate hose-end bond is needed. At the end, the order reverses: the bonding wires stay on until the filler caps have been refitted or the pressure hose has been disconnected.
Part 4 · Refuelling
During fuelling, and special hazards Passengers Boarding or leaving passengers are supervised and their route avoids the fuelling zones .
Steps and jacks Keep steps, trestles and jacks clear : the aircraft settles as it gets heavier.
Engines and lights Main engines not run ; no strobe lights; torches and lamps flameproof or intrinsically safe .
Spill or vapour Stop fuelling; clear the area; call the fire service if the spill is large.
Radar No fuelling within 30 m (100 ft) of radar equipment under test or in use.
Hot brakes Landing gear overheated : call the fire service ; no fuelling until the heat has gone.
Thunderstorms Extreme caution; suspend fuelling during severe electrical storms nearby.
Flash No photographic or electronic flash within 6 m (20 ft) of fuelling or vent points.
Chapter 22 · Fuel Systems and Refuelling
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the precautions during fuelling and the special hazards. Passengers who are boarding or leaving are supervised by an airline official and their route keeps them out of the fuelling zones. Steps, trestles and jacks are moved clear, because the aircraft settles on its landing gear as fuel goes in. The main engines must not be run, strobe lights must not be used, and any torches or lamps inside the zone must be certified flameproof or intrinsically safe. If fuel is spilt or vapour is detected, stop fuelling. Then the special hazards. Do not fuel within thirty metres, or a hundred feet, of radar equipment that is being tested or used. If the landing gear has overheated, call the fire service and wait until the heat has dissipated. Suspend fuelling during severe electrical storms near the airfield. And no photographic flash within six metres of the fuelling or vent points.
Part 4 · Refuelling
Refuelling with passengers on board Allowed by many operators to save turnaround time, but only under these conditions:
Condition Requirement Fuel type Not with AVGAS or wide-cut fuel (e.g. Jet B): passengers must disembarkAircraft size Exam rule: not on fixed-wing aircraft with fewer than 20 seats Qualified person One qualified person at a specified location, able to handle fire, communications and an evacuation Warnings and signs Crew, staff and passengers warned ; seat belt signs OFF ; NO SMOKING ON with interior lights so exits can be seen Passengers Told to unfasten seat belts and not to smoke Crew Enough qualified personnel on board , ready for an immediate evacuation Vapour or hazard Fuel vapour in the cabin or any other hazard: stop fuelling immediately Exits Ground under exits and slide areas kept clear ; catering and cleaning must not obstruct exits
Chapter 22 · Fuel Systems and Refuelling
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many operators refuel with passengers on board to save turnaround time, but only under strict conditions. First, the fuel: if AVGAS or a wide-cut fuel like Jet B is involved, the passengers must disembark. The reference also gives an exam rule that it is not permitted on fixed-wing aircraft with fewer than twenty seats. One qualified person must stay at a specified location, able to deal with fire, handle communications and start and direct an evacuation. Crew, staff and passengers are warned that fuelling is about to begin. The seat belt signs are off, so people can get out quickly, and the no smoking signs are on, with enough interior lighting to identify the exits; passengers are told to unfasten their belts. Enough qualified crew stay on board ready for an immediate evacuation. If fuel vapour appears in the cabin, fuelling stops at once, and the ground under the exits and slide areas is kept clear.
Part 4 · Refuelling
Keeping the exits ready Evacuation must be possible through at least two main passenger doors , preferably at opposite ends (or one main door plus an emergency exit) With automatic slides, bridge in use : no extra steps needed, but the left or right rear door is manned by cabin crew, slide ready (girt bar engaged)With slides, no bridge : steps at the open main door used for boardingWithout automatic slides, bridge in use : steps at another open door, preferably at the opposite end Without slides, no bridge : steps at two main doors , one forward and one aft; integral airstairs count as one exit
loading bridge
rear door manned, slide ready
bowser
passenger route clear of the fuelling zone
Chapter 22 · Fuel Systems and Refuelling
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
During fuelling with passengers on board, the aircraft must be ready for a rapid evacuation through at least two main passenger doors, preferably at opposite ends of the aircraft, or one main door plus an emergency exit if there is only one main door. The details depend on the equipment. On a wide-body with automatic inflatable slides, when a loading bridge is in use no extra steps are needed, but either the left or the right rear door is manned constantly by a cabin attendant and kept ready as an emergency route using its slide; where the slide needs a girt bar fitting, it stays engaged throughout. Without a bridge, steps are placed at the open main door used for boarding. On aircraft without automatic slides, with a bridge in use, steps go to another open door at the opposite end; with no bridge, steps go to two main doors, one forward and one aft. Integral airstairs count as one exit.
Summary
Fuel systems: the points to remember Tanks Integral (airliners), rigid (light aircraft), flexible (military). Baffles stop surging; vents with 2% expansion space and a surge tank.
Pumps and feed Boosters: centrifugal, AC, 20–40 psi , in a collector box ; also transfer and jettison. Cross-feed : any tank to any engine. Centre tank first.
Shut-offs LP valve closed by the fire handle; HP valve stops the engine. LP pump backs up a double booster failure.
Jettison Outboard trailing-edge nozzles; stopped by preselection and low-level switches ; leave fuel for 10 000 ft + 45 min.
Gauging Capacitance: mass , density and attitude compensated. Power failure: slowly to empty . Water: full scale high .
Refuelling 6 m zones; APU started first; bond first, unbond last ; no AVGAS or Jet B with passengers aboard; radar 30 m.
Chapter 22 · Fuel Systems and Refuelling
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the key points. Airliners use integral tanks; light aircraft use rigid tanks; military aircraft like flexible, self-sealing bags. Baffles stop surging, and the vent system keeps two per cent expansion space and catches overflow in a surge tank. Booster pumps are centrifugal, electrically driven, low pressure and high flow, sitting in a collector box; they also transfer and jettison fuel. The cross-feed lets any tank feed any engine, and centre tank fuel is used first. The fire handle closes the low-pressure shut-off valve, and the engine pump can keep going after a double booster failure. Jettison stops at the preselected figure or the low-level switches. Capacitance gauges measure mass, read slowly towards empty on power failure, and full scale high with water. For refuelling: six metre zones, APU started before fuelling, bond first and unbond last, and never passengers on board with AVGAS or Jet B.