Aircraft Systems · Chapter 15
Ground De-icing and Anti-icing How frost, ice and snow are removed on the ground, how anti-icing fluids protect the aircraft until take-off, and the checks that make sure it leaves clean.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to ground de-icing and anti-icing. An aircraft that has stood overnight in frost or snow, or landed with cold fuel in its wings, can carry a deposit that would ruin its take-off. In this lesson you will learn the clean aircraft concept, how frost, snow and ice are removed with hot fluid or hot water, how thickened fluids protect the wings until take-off and then shear off, what holdover time really means, and the precautions and checks that make sure the aircraft leaves the ground clean.
Roadmap
Leaving the ground clean 1 · Why The clean aircraft concept: what ground deposits do, cold soak and the conditions that cause them.
2 · The fluids Freezing point depressants: Type I, II and IV, mixture strength and how thickened fluids work.
3 · Removing deposits Frost, snow and ice; cold spray, hot fluid and hot water; high-pressure precautions.
4 · Protecting until take-off One-step and two-step treatment, anti-icing film and holdover time.
5 · Special cases De-icing with engines or APU running, fluid residues, pastes, helicopters.
6 · Checks Inspection after de-icing, pre-take-off checks and the commander’s decision.
Chapter 15 · Ground De-icing and Anti-icing
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how this lesson runs. First, why ground de-icing matters: the clean aircraft concept, what frost, ice and snow on the ground do to an aircraft, and how cold-soaked fuel can grow ice on a wing even when the air is above freezing. Second, the fluids: freezing point depressants of Type one, Type two and Type four, how strong to mix them, and the clever way thickened fluids stay on the wing and then shear off. Third, removing deposits, with cold spray, hot fluid and hot water. Fourth, protecting the aircraft until take-off, with one-step and two-step treatment and holdover time. Then the special cases, such as de-icing with engines running, and finally the checks that must happen before the aircraft is allowed to take off.
Where ground deposits come from
Frost, ice and snow on a parked aircraft Precipitation : snow, freezing rain and drizzle, freezing fog, frost on clear nightsCold soak : frost or ice over integral fuel tanks after a long high-altitude flightSlush and snow thrown onto the gear, flaps and undersurfaces while taxiingEffects: less lift, more drag, more weight ; frozen controls, hinges, microswitches ; ice ingested by engines In-flight systems start working only in the climb, so ground treatment must also cover the first part of the flight
snow, frost, freezing rain on upper surfaces cold fuel (−20 °C): frost or clear ice on the tank skin slush from taxiing
Lift ↓ · drag ↑ · weight ↑ · controls freeze engines ingest ice · instruments read wrong
Chapter 15 · Ground De-icing and Anti-icing
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Frozen deposits on a parked aircraft come from three places. The obvious one is precipitation: snow, freezing rain and drizzle, freezing fog, and frost on a clear, still night. The second is cold soak. After a long flight at high altitude the fuel in the integral wing tanks may be far below zero, and frost or ice forms on the skin above and below those tanks. The third is taxiing through snow or slush, which throws deposits onto the landing gear, flaps and undersurfaces. The effects are serious: less lift and more drag from the disturbed airflow, extra weight, moisture freezing in control hinges and microswitches, and ice swallowed by the engines. And remember that the aircraft’s own ice protection only becomes effective once it is established in the climb, so ground treatment must also protect the first part of the flight.
The golden rule
The clean aircraft concept No take-off with frost, ice or snow adhering to wings, tail, control surfaces, propellers or intakesCertification for icing covers supercooled cloud in flight , never ice formed on the ground Some manuals allow thin frost on the fuselage and under the wing tanks , within stated limits (a few mm) Upper-wing and leading-edge frost is far worse than underwing frost The final decision belongs to the commander : if the aircraft cannot be confirmed clean, do not take off
Critical surfaces
fuel tank
leading edge + upper surface: nothing may remain
underwing tank area: thin frost only if the manual allows
Icing certification ≠ ground ice
An aircraft cleared for flight in icing is tested in supercooled cloud.
It is not certified to take off with ice formed on the ground:
it must be clean before and throughout the take-off roll.
Chapter 15 · Ground De-icing and Anti-icing
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Everything in this lesson serves one rule, the clean aircraft concept: no aircraft may take off with frost, ice or snow adhering to its wings, tail, control surfaces, propellers or engine intakes. It is worth understanding why certification does not help. An aircraft cleared for flight in icing conditions has been tested in supercooled cloud in flight, where ice forms on protected leading edges. It is not certified to take off with ice formed on the ground, which covers whole surfaces with a rough layer. Some maintenance manuals do allow a thin layer of frost on the fuselage, or under the wing over the fuel tanks, within stated limits of a few millimetres, because research shows underwing frost matters much less than frost on the leading edge and upper surface. In the end the decision belongs to the commander, and if the aircraft cannot be confirmed clean, the take-off must not be attempted.
What ice does
Effects of ice, snow and frost accretions Lift and drag Even slight roughness raises the stall speed and the power needed. Leading-edge roughness matters most.
Stall Stall angle of attack falls ; the stall may come before the stall warning , with pitch-up or roll-off.
Handling Less control effectiveness; ice or excess fluid can cause control surface flutter ; trim may deteriorate.
Frozen mechanisms Ailerons, elevators, spoilers, cables and jacks can freeze in place ; flaps damaged if retracted with ice.
Engines and props Intake ice, ingestion , blocked fuel vents; asymmetric shedding from props or rotors causes severe vibration.
Instruments Ice on pitot-static probes gives wrong airspeed, altitude, EPR , and misleads autopilot and autothrottle.
Gear, doors, seals Gear frozen or damaged; frozen door seals may leak or not open in an emergency.
Hidden margins Effects may not show until an engine failure or other emergency demands the full performance.
Chapter 15 · Ground De-icing and Anti-icing
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
What can ground ice actually do? Even slight surface roughness raises the stall speed and the power needed to fly, and roughness on the leading edge is the most damaging. The stalling angle of attack falls, so on some aircraft the stall arrives before the stall warning or stick shaker, and it may come with a sharp pitch-up or wing drop. Control effectiveness falls, and ice or excessive fluid has caused control surface flutter. Ailerons, elevators, spoilers, cables and jacks can freeze solid, and flaps can be damaged if retracted with ice on them. Engines can swallow ice, fuel vents can block, and uneven shedding from propellers causes severe vibration. Iced probes give false airspeed, altitude and engine pressure ratio. Gear, doors and seals can freeze. And the most dangerous point of all: the aircraft may seem fine until an engine fails and it needs every bit of its performance.
The words used
Weather terms for de-icing Term Meaning Freezing conditions OAT below +3 °C with visible moisture (fog under 1.5 km, rain, snow, sleet, ice crystals) or water, slush, ice or snow on the runway Active frost Frost is forming: surface temperature at or below 0 °C and at or below the dew point Freezing fog Tiny droplets that freeze on impact; visibility usually below 1 km Freezing drizzle Fine drops, under 0.5 mm , close together, freezing on impact Freezing rain Drops over 0.5 mm (or smaller, widely spaced); light = up to 2.5 mm per hour Sleet (rain and snow)Treat as light freezing rain for holdover purposes Snow grains Very small white grains under 1 mm; treat as snow Holdover time Estimated time the anti-icing fluid prevents frost, ice and snow on protected surfaces in given weather
Chapter 15 · Ground De-icing and Anti-icing
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
De-icing has its own precise vocabulary. Freezing conditions means an outside air temperature below plus three degrees with visible moisture, such as fog with visibility under one and a half kilometres, rain, snow, sleet or ice crystals, or with water, slush, ice or snow on the runway. Active frost means frost is actually forming: the surface is at or below zero and at or below the dew point. Freezing fog is made of tiny droplets that freeze on impact, usually with visibility below one kilometre. Freezing drizzle has fine drops under half a millimetre, close together, while freezing rain has bigger drops, or smaller ones widely spaced. For holdover purposes, sleet is treated as light freezing rain and snow grains are treated as snow. And holdover time is the estimated time for which the anti-icing fluid will keep frost, ice and snow off the protected surfaces in specified weather.
Cold soak
Clear ice on a wing in air above freezing A wing is cold-soaked when it holds very cold fuel : after a long high-altitude flight, or refuelling with very cold fuel Rain, drizzle or high humidity falling on it can form clear ice even when the OAT is above 0 °C Worst over the integral tanks : underwing frost, and upper-surface ice where fuel touches the skin Factors: fuel temperature and quantity , tank type and position, time at altitude , refuelled fuel temperature, time since refuelling Clear ice on a wet wing is hard to see : it must be checked by touch or by special detectors
OAT +4 °C, rain
fuel −20 °C
clear ice over the tank frost under the tank
Cold-soak checklist
· fuel temperature and quantity in the tanks · type and position of the tanks; time spent at high altitude · temperature of the fuel taken on, and time since refuelling · clear ice is transparent: check by touch
Chapter 15 · Ground De-icing and Anti-icing
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a trap that catches crews out. A wing is said to be cold-soaked when it holds very cold fuel, either because the aircraft has just landed after a long flight at high altitude, or because it was refuelled with very cold fuel. The skin in contact with that fuel can stay well below zero for a long time. If rain, drizzle or even high humidity then meets it, clear ice can form on the wing although the outside air is above freezing. It is worst over the integral tanks, with frost underneath and ice on the upper surface where the fuel touches the skin. How much cold soak there is depends on the fuel’s temperature and quantity, the type and position of the tanks, the time spent at altitude, the temperature of the fuel taken on and the time since refuelling. Clear ice on a wet wing is almost invisible, so it is checked by touch or with special detectors.
Why not simply…
Why the aircraft’s own systems will not do In-flight systems protect only leading edges and nacelles ; ground deposits cover whole surfaces Using them on the ground can melt part of a deposit, which runs back and refreezes elsewhere Cabin heating to clear the fuselage: the same problem, not recommendedA heated hangar works, but melted snow refreezes once the aircraft is outside; big aircraft and quick turnrounds make it rare Covers on wings, screens, intakes and probes reduce the work but do not remove the need to check
Melt, run back, refreeze
heated leading edge melt water runs back refreezes as a ridge snow still there
Wing anti-ice on the ground: partial melting, runback iceCabin heat: same problem on the fuselageHangar: melted snow refreezes outsideCovers: less work, still inspectSo: proper de-icing fluids and procedures
Chapter 15 · Ground De-icing and Anti-icing
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why not just switch on the aircraft’s own anti-icing? Because those systems are designed to protect particular areas, the leading edges and engine nacelles, in flight. Snow, frost and ice on the ground cover whole surfaces, which the systems were never meant to clear. Worse, heating the leading edge on the ground melts part of the deposit; the water runs back over the cold upper surface and refreezes as a ridge, which is even more harmful than the snow. Using the cabin heating to clear the fuselage is not recommended for the same reason. A heated hangar would give complete protection, but melted snow on an aircraft refreezes as soon as it is moved out into sub-zero air, and the size of modern aircraft and short turnround times make hangars impractical. Covers on wings, windscreens, intakes and probes reduce the work, but the aircraft must still be de-iced and checked properly.
Freezing point depressants
Type I, Type II and Type IV fluids All are glycol-based freezing point depressant (FPD) fluids, mixed with water. The difference is the thickener .
Type I Type II Type IV Thickener None : unthickenedThickened Thickened (advanced system) Glycol content High (about 80 %)At least about 50 % Similar to Type II Viscosity Low : runs off quicklyHigh at rest, thins under shearHigh at rest, thins under shear Main use De-icing , usually hot; first stepAnti-icing : stays on until take-offAnti-icing: the longest holdover Holdover Short ; a stronger mix adds almost nothingLonger; stronger mix = longer Longest when concentrated Usual colour Clear (often dyed orange ) Straw / pale yellowGreen
Thickened fluids are designed to shear off during the take-off run. Only fluids approved by the aircraft manufacturer may be used.
Chapter 15 · Ground De-icing and Anti-icing
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
All de-icing and anti-icing fluids are glycol-based freezing point depressants, mixed with water to the strength the weather needs. What separates the types is the thickener. Type one is unthickened. It has a high glycol content and a low viscosity, so it is excellent at de-icing, especially hot, but it runs off quickly and gives only limited protection against refreezing; making it stronger adds almost nothing to the holdover time. It is usually clear, though modern fluids are often dyed orange. Type two has at least about fifty per cent glycol and a thickening agent, so it clings to the surfaces until take-off and protects against further snow or freezing rain; the stronger the mix, the longer it lasts. It is usually straw coloured. Type four works the same way but with an advanced thickener, giving the longest holdover times when concentrated, and it is usually green.
How thickened fluid works
Thick at rest, thin on the take-off run Type II and IV are pseudoplastic : viscosity falls as the shear rate rises At rest the film is thick and stays put, soaking up precipitation; Type I stays thin On the take-off run the airflow shears it: it thins and flows off by rotation If rotation is slow (some turboprops below about 100 kt ), fluid may remain: lift loss Manufacturers may require a mass reduction or higher rotation speed ; brief it before take-off
0.1 1 10 100 1 000 10 000 100 000
1 10 100 1 000 10 000 100 000
shear rate (per second, log scale)
viscosity (mPa s, log)
Type II / IV: at rest thick film stays on
take-off run thins, flows off
Type I: thin at all times
illustrative model of a typical thickened fluid
Chapter 15 · Ground De-icing and Anti-icing
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
How can a fluid stay on a parked aircraft for half an hour, yet be gone by the time it lifts off? The answer is that thickened fluids are pseudoplastic: their viscosity falls as the shear rate rises. On the graph, Type one is a flat, low line: it is thin whatever you do to it, so it runs off quickly. Type two and Type four start thousands of times thicker at rest, so the film stays on the wing and soaks up falling snow or freezing drizzle. Once the take-off run starts, the airflow shears the film, its viscosity collapses, and it flows off the wing before rotation. But that needs speed. On some turboprops that rotate below about one hundred knots, fluid has stayed on and caused a loss of lift, and jets have been affected too. So manufacturers may require a reduced mass or a higher rotation speed with certain fluids, and the crew must include this in the take-off briefing.
Mixture and temperature
Mixing, measuring and heating the fluid Mix exactly as recommended: diluted fluid de-ices well but protects poorly , and a wet surface can collect wet snow Typical stocks: 50/50 or 60/40 fluid/water; a refractometer checks the real strength In extreme cold, neat thickened fluid may be heated, 60 °C maximum , to make it spray easily A dual-purpose fluid used for de-icing is mixed with water and applied at about 70 °C Overheating in the rig makes most fluids gel : a residue that will not shear off at take-off
Strength and heat
100/0 75/25 60/40 50/50
more water → weaker → shorter holdover , higher freezing point
Refractometer
reads the refractive index: converted by chart to the fluid/water mix and freezing point. Check, do not trust the label.
gelling if overheated≈ 70 °C hot de-icing mix60 °C max : neat fluid,for sprayability
Chapter 15 · Ground De-icing and Anti-icing
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fluid only works at the right strength. Mixed with water it still removes ice well, but its ability to stop ice re-forming falls sharply, and in some conditions a wet, diluted surface actually collects wet snow faster. Stations commonly hold fifty-fifty or sixty-forty mixes, and a pocket refractometer measures the real concentration, which a chart converts into the mix and its freezing point. Two temperatures matter. In extreme cold, neat thickened fluid may be heated to make it sprayable, but never above sixty degrees. A dual-purpose fluid used for de-icing is mixed with water and sprayed at about seventy degrees. Heating does not make an anti-icing fluid protect for longer; in fact, unheated fluid is the better anti-icer. And overheating the fluid in the rig is dangerous: most fluids then form a gel that sticks to the aircraft and will not shear off on the take-off run.
Treating frost
Removing frost A frost remover (glycol and isopropyl alcohol) by spray or by hand; one application, within 2 hours before flight Severe frost: a de-icing fluid Or a mobile hot-air blower : blows off or melts frost, but dry up water so it cannot refreeze in hinges and switches Fluids can harm new paint and glazed panels ; use only approved fluid Alcohol fluids wash out grease : water gets in and freezes, jamming controls; do not spray bearings, re-lubricate if required
Frost remover spray or by hand, within 2 h of flight De-icing fluid for severe frost glycol based Hot-air blower blows off or melts dry the water up!
Cautions
control hinge
· fluid may damage new paint and glazed panels · alcohol washes out grease from bearings; water gets in and refreezes: jammed controls · do not aim at lubrication points or sealed bearings · inspect where fluid is trapped; re-lubricate if the maintenance schedule says so
Chapter 15 · Ground De-icing and Anti-icing
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Frost is the easiest deposit to deal with. It is usually removed with a frost remover, a mixture of glycol and isopropyl alcohol, sprayed or applied by hand. One application is normally enough provided it is done within the two hours before flight. In severe conditions a de-icing fluid is used instead. Another method is a mobile hot-air blower, which blows the frost away or melts it; but any water must then be dried up, or it will run into hinges and microswitches and refreeze there. There are cautions with fluids too. They can damage new paint and glazed panels, so only the fluid approved by the manufacturer may be used. Alcohol-based fluids can dilute or wash out the grease from control bearings, letting water in to freeze and jam the controls. So nozzles should never be aimed at lubrication points or sealed bearings, and the maintenance schedule may call for re-lubrication after de-icing.
Treating snow and ice
Snow and ice: match the method to the deposit Deep wet snow, OAT just above 0 °C The hardest deposit. Remove with a brush or squeegee , taking care of hidden aerials, vents, stall vanes, pitot probes and vortex generators.
Light dry snow, below 0 °C Blow it off . Do not use hot air: the snow would melt and then refreeze.
Moderate or heavy ice, residual snow Spray de-icing fluid ; in severe conditions a final application immediately before flight.
Never by force Do not chip ice or break its bond by force: the skin and fittings are easily damaged.
Always symmetrical Remove deposits symmetrically , both wings and both sides of the tail, so the aircraft stays balanced.
Keep the screens dry Leave the nose and windscreens free of fluid ; never wipe them with alcohol or use the screen heat to clear them.
Chapter 15 · Ground De-icing and Anti-icing
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Snow and ice need the right method for the deposit. The most awkward is deep wet snow when the temperature is just above freezing. It is removed with a brush or squeegee, carefully, because it hides aerials, vents, stall warning vanes, pitot probes and vortex generators that are easily broken. Light, dry snow in sub-zero temperatures should simply be blown off. Hot air is not used, because it melts the snow, which then refreezes and needs treating again. Moderate or heavy ice and any residual snow are removed by spraying de-icing fluid, and in severe weather a final application may be needed immediately before flight. Never try to break ice off by force, and always remove deposits symmetrically. Finally, the nose and windscreens are left dry, so fluid cannot smear the screens; they must not be wiped with an alcohol-soaked cloth or cleared with the windscreen heat.
Applying fluid
Cold spray or hot spray? Cold spray : simple, but melting ice dilutes the fluid, which loses strength and may refreeze in controls and gear; several coats: slow and costlyHot spray : fluid and water heated in a static unit, carried in an insulated tank on a mobile rigSprayed at about 70 °C and 100 psi (700 kN/m²), nozzle close to the skin Heat breaks the ice bond ; turn the nozzle sideways to flush large sheets away Little dilution, so the remaining film still protects against re-forming
70 °C fluid temp.
100 psi ≈ 700 kN/m²
heat breaks the ice bond: nozzle close to the skin turn the nozzle sideways to flush sheets of ice away little dilution: the film left behind still protects
never overheat the rig: the fluid gels and will not shear off
Chapter 15 · Ground De-icing and Anti-icing
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fluid can be sprayed cold or hot. A cold spray is the simplest method, but it has drawbacks. In bad conditions one coat is rarely enough, so iced areas need brushing and a second or third coat. As the ice melts, it dilutes the fluid, which loses strength and can refreeze quickly, and diluted fluid running into control and landing gear mechanisms is dangerous. So it is slow and expensive. Most airlines use hot spray instead. Water and fluid are heated in a static unit, carried in an insulated tank on a mobile rig with a raised platform, and sprayed at about seventy degrees and one hundred p s i, about seven hundred kilonewtons per square metre, with the nozzle held close to the skin to keep the heat. The heat breaks the bond between ice and skin, and turning the nozzle sideways flushes large sheets away. Because there is little dilution, the film left behind still protects against re-forming.
The cheaper alternative
Hot water de-icing: two steps against the clock
0 min 1 min 2 min 3 min 4 min
STEP 1 · hot water jet removes snow and ice · water ≤ 95 °C
STEP 2 · fluid coat light coat stops refreezing
step 2 must start within 3 minutes of the start of step 1
Limits
OAT not below -7 °C · water not above 95 °C
Why
water left on a cold skin refreezes fast: work area by area
Hot water is far cheaper than glycol, but it protects for only a few minutes, so the fluid coat must follow quickly.
Chapter 15 · Ground De-icing and Anti-icing
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
With glycol so expensive, many operators use very hot water for the first step. It is a two-step process against the clock. Step one is a jet of hot water, at no more than ninety-five degrees, which melts and blasts away the snow and ice. Water alone gives almost no protection, because what is left on a cold skin soon refreezes, so step two, a light coat of de-icing fluid, must follow immediately. The rule is that step two must begin within three minutes of the start of step one, and if necessary the aircraft is done area by area to meet that limit. There is also a temperature limit: hot water de-icing must not be used when the outside air is colder than minus seven degrees. Remember the three numbers together: ninety-five degrees, minus seven degrees and three minutes.
Procedures
One-step and two-step treatment
One-step
heated fluid mix: de-ices AND anti-ices one application
holdover counts from the START of the treatment
Two-step
1 · DE-ICE hot water or hot Type I
2 · ANTI-ICE cold, stronger II / IV, before refreeze
holdover counts from the START of step 2
The anti-icing coat
· sprayed cold and undiluted : unheated fluid anti-ices better than heated fluid
· leaves a film about 0.5 mm thick that stops snow and ice sticking and melts fresh precipitation; excess shears off on take-off
· the time the anti-icing (or the one step) started goes in the technical log , with the anti-icing code passed to the crew
Never spray a new anti-icing coat over a contaminated one: repeat the complete de-icing/anti-icing process.
Chapter 15 · Ground De-icing and Anti-icing
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Treatment can be done in one step or two. In the one-step process a heated fluid mix both removes the deposit and leaves the protective film, all in one application, and the holdover time counts from the start of that treatment. In the two-step process, step one de-ices, using hot water or hot, diluted fluid, and step two anti-ices with a cold, stronger thickened fluid, applied before the first step has had time to refreeze. Here the holdover time counts from the start of step two. Why cold for anti-icing? Because unheated, undiluted fluid protects better than heated fluid. It leaves a film about half a millimetre thick, which stops snow and ice sticking and melts fresh precipitation, and the excess shears off on take-off. The start time goes in the technical log, and the anti-icing code is passed to the crew. And never spray new anti-icing over a contaminated coat: the whole process must be repeated.
Holdover time
How long will the protection last? Holdover is only an estimate , so the aircraft must still be checked . Illustrative generic values (h:min) at about −3 °C:
Fluid / water mix Frost Freezing fog Snow Freezing drizzle Type II 100/0 (neat) ≈ 8 h 0:35 – 1:30 0:20 – 0:45 0:30 – 1:00 Type II 75/25 ≈ 5 h 0:25 – 1:00 0:15 – 0:30 0:20 – 0:45 Type II 50/50 ≈ 3 h 0:20 – 0:45 0:05 – 0:15 0:05 – 0:15 Type I (any mix) ≈ 0:45 0:10 – 0:20 0:05 – 0:10 0:05 – 0:10
Shortened by heavier precipitation, wind or jet blast, a cold-soaked wing, a surface colder than the air. Longest: neat thickened fluid, cold ; Type IV beats Type II. Use the current tables for the brand.
Chapter 15 · Ground De-icing and Anti-icing
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
How long will the fluid protect the aircraft? That is the holdover time, and it is only an estimate taken from tables for the type of fluid, its concentration, the outside temperature and the type of precipitation. The table shows illustrative values for a Type two fluid at about minus three degrees. Notice the pattern. Neat fluid, applied cold, lasts longest, and every bit of water shortens the protection: in freezing fog a fifty-fifty mix might give only twenty to forty-five minutes. Snow and freezing drizzle use up the fluid much faster than frost. Type one lasts only minutes. Type four, the green fluid, lasts longer still. And many things shorten the real time: heavy precipitation, strong wind or jet blast, a cold-soaked wing, and a surface colder than the air. That is why nobody can say exactly how long a treatment will last, and why the aircraft must still be inspected before take-off. Always use the current tables for the actual brand of fluid.
Spraying safely
High-pressure sprays and no-spray areas High-pressure spray can damage pitot-static probes and other sensors Fluid driven into engine and APU intakes , drains or vents can cause cabin smoke or system faults Fit covers and bungs where provided; otherwise never aim directly at probes or vents Respect the manufacturer’s maximum impingement pressure : skins can be eroded Do not spray windscreens : fluid smears and restricts vision
windscreens probes, AoA vanes, static ports engine (and APU) intakes
Covers and bungs fitted; spray never aimed straight at them
Chapter 15 · Ground De-icing and Anti-icing
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fluid must go where it is needed and nowhere else. A high-pressure spray can easily damage pitot-static probes and other sensing devices, and a carelessly aimed jet can drive a lot of fluid into engine and APU intakes, drains or vents. Fluid in an intake can be drawn into the air-conditioning and cause smoke and fumes in the cabin, or make an aircraft system malfunction. So where covers or bungs are provided they are fitted during de-icing, and where they are not, the operator must take care never to spray directly at vents or probes. High-pressure sprays can also erode the skin, so manufacturers quote a maximum impingement pressure in the maintenance manual, which must not be exceeded. And, as we saw, the windscreens are kept free of fluid, because it smears and severely restricts the pilots’ vision.
De-icing with engines running
Gantries, taxi-through pads and the bleeds Taxi-through or gantry facilities de-ice aircraft with engines and APU running Close the engine and APU bleeds (and packs) so fluid fumes cannot enter the cabin airUndiluted fluid has a flashpoint of about 139 to 156 °C , inside the engine/APU operating range Some fluids are toxic if ingested by the air-conditioning; keep spray out of intakes and exhausts Follow the manufacturer’s instructions; fire cover readily available
overhead gantry
slow taxi
May run: engines and APU Must be shut: bleeds, packs
Fluid flashpoint 139 – 156 °C (undiluted): fire cover ready
APU
Chapter 15 · Ground De-icing and Anti-icing
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
At many airports aircraft are de-iced on taxi-through pads or under overhead gantries with the engines and the APU running. That creates hazards if the wrong fluid, or too much of it, is sprayed into the intakes or onto hot exhausts. The key rule for the exam: the engines and APU may be running, but their bleed air valves must be closed, and the packs off, so fluid vapour is not drawn into the air-conditioning and the cabin. Why the concern about heat? Undiluted de-icing fluid has a flashpoint of roughly one hundred and thirty-nine to one hundred and fifty-six degrees, which is within the temperatures found in engines and APUs. Some fluids are also toxic if passengers or crew breathe them. So procedures must keep the fluid diluted below its critical flashpoint and out of ducts, intakes and exhausts, the manufacturer’s instructions must be followed, and fire and emergency equipment must be on hand throughout.
After de-icing
Inspecting the aircraft after de-icing
flap and aileron gaps elevator and rudder hinges gear, brakes, wells intake: compressor free? doors and seals
Surfaces and gaps Look for residual snow or ice, especially in control surface gaps and hinges and seals; check drains, pressure holes, honeycombs.
Controls Move surfaces by hand for full, free travel; with powered controls move the flight-deck controls gently .
Landing gear Gear, doors, bays and brakes : check uplocks and microswitches for ice.
Frozen tyres Free a tyre frozen to the ground with warm air on the ice , not on the tyre; then move to a dry area.
Engines Snow can enter after flight and freeze in the compressor : if it will not turn by hand, blow hot air through before start.
Cold-weather leaks Metal and seals contract: watch shock struts and hydraulic jacks for leaks.
Pressures Tyre and strut pressures fall with temperature; adjust them to the loading requirements.
Records Enter the treatment in the technical log , even if it was interrupted or failed.
Chapter 15 · Ground De-icing and Anti-icing
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once de-icing is finished, the aircraft is inspected, and it should be watched right up to departure, because ice in some places is not obvious to the people spraying. All external surfaces are checked for residual snow or ice, above all in control surface gaps and hinges and behind sealing curtains. Drains, pressure-sensing holes and radiator honeycombs must not be blocked. Control surfaces are moved by hand to prove full and free travel; with powered controls, the flight-deck controls are moved gently, because a powerful actuator could damage a frozen surface. The landing gear, doors, bays and brakes are checked, including uplocks and microswitches. A tyre frozen to the ground is freed by warm air on the ice, never on the tyre. An engine that will not turn by hand is blown through with hot air before start. Cold makes seals leak and tyre and strut pressures fall. And the treatment is always entered in the technical log.
The final checks
Pre-flight, pre-take-off and contamination checks Pre-flight check straight after treatment, from a checklist: wings, tail, controls, props, intakes, probes, vents, gearPre-take-off check by the commander , from inside , just before take-off: is the holdover still valid?Treated surfaces should look glossy, smooth and wet ; any ice, snow or frost: back for de-icing Pre-take-off contamination check : from outside , visual and by touch, when the inside view is not good enough (e.g. holdover exceeded)The alternative to that outside check is a complete re-treatment
De-icing / anti-icing done time and code to the crew; tech log
Pre-flight check checklist, all critical areas
Pre-take-off check (inside) commander · holdover still valid?
glossy, smooth, wet → take off without delay
doubt / holdover exceeded → contamination check (outside, look and touch)
or full re-treatment de-ice AND anti-ice again
Never a fresh anti-icing coat over a contaminated film.
Not sure it is clean? Do not go.
Chapter 15 · Ground De-icing and Anti-icing
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Several checks stand between treatment and take-off. First, a pre-flight check immediately after treatment, using a checklist that covers the wings, tail, control surfaces, propellers, intakes, probes, fuel vents and landing gear. Once the aircraft is confirmed clean it should be released as soon as possible. Then, just before take-off, the commander makes the pre-take-off check, normally from inside the aircraft, assessing whether the holdover time is still appropriate and looking at whatever surfaces can be seen. Surfaces treated with fluid should look glossy, smooth and wet. Any sign of snow, ice or frost means returning for more de-icing. If the inside view is not good enough, for example at night or when the holdover time has been exceeded, a pre-take-off contamination check is made from outside, by looking and touching, or the aircraft gets a complete re-treatment. A fresh anti-icing coat is never sprayed over a contaminated film.
A hidden hazard
Dried fluid residues that come back to life Repeated thickened-fluid use leaves residues in quiet areas: balance bays , trailing edges, rear spars, hinges, cable pulleys In flight the residue can rehydrate , swell to many times its size and freeze Result: elevators, ailerons and flap mechanisms stiffen or jam ; drainage and balance upset Prevention: inspect at set intervals; prefer a two-step process with hot water or Type I in step one to wash residues off Infra-red and forced-air de-icing lose that washing step, so watch for residues
Balance bay of an elevator
fixed stabiliser elevator
dried thickener residue
1 · dries after repeated thickened fluid 2 · rehydrates rain or humidity swells many times 3 · freezes at altitude: controls stiffen or jam
Chapter 15 · Ground De-icing and Anti-icing
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thickened fluids have a hidden side effect. When they are used again and again, some fluid collects in aerodynamically quiet areas, such as control balance bays, the trailing edges and rear spars of the wing and stabiliser, around hinges and on cable pulleys, and there it dries out into a gel residue. Later, in rain or high humidity, that residue can rehydrate, swelling to many times its original volume, and then freeze at altitude. Elevators, ailerons and flap mechanisms have stiffened or jammed in flight because of it, and residues can block drains and upset control balance. Operators therefore inspect these hidden areas at set intervals, following the manufacturer’s guidance, and are encouraged to use a two-step process with hot water or unthickened Type one fluid in the first step, which washes residues away. Infra-red and forced-air de-icing remove ice by heat, but they lose that washing step, so residues need closer watching.
Special cases
Pastes, small aircraft, helicopters and intakes De-icing paste Spread on the leading edges of unprotected aircraft so ice cannot bond ; reactivate before each flight. Not approved for intended flight into known icing.
Equipment ≠ certification Many small aircraft have ice protection fitted but are not certified for icing: the kit was only shown to be harmless.
Helicopters FPD fluids are not formally approved by rotorcraft makers. Rotors must be clean before they turn ; shed ice is lethal.
Turboprop intakes Snow and slush can collect in intakes while parked: fit intake blanks and check inside, or risk a flame-out on taxi or take-off.
Slush on the tailplane Mud and slush thrown up on taxi can freeze on the underside of the tailplane . Do not take off if slush splashes critical areas.
Boot treatments Products approved for pneumatic boots must not be used elsewhere unless the manufacturer approves.
Chapter 15 · Ground De-icing and Anti-icing
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few special cases complete the picture. On some aircraft without leading-edge protection, a de-icing paste may be spread by hand on the wings and tail, giving a chemically active surface on which ice cannot bond; it must be reactivated before each flight, and it is not an approved way to fly into known or forecast icing. Many small aircraft carry ice protection equipment without being certified for icing; it was only shown to be harmless, so it may not keep the aircraft safe. Helicopter makers have not formally approved de-icing fluids, rotor blades must be clean before the rotors turn, and ice flung from a rotor or propeller can kill. Turboprops parked in snow can collect snow and slush in their intakes, which has caused flame-outs on taxi and take-off, so intake blanks and inspections are essential. And slush thrown onto the underside of the tailplane during taxi can freeze there.
Summary
Ground de-icing: the numbers and the rules Topic Remember Clean aircraft No frost, ice or snow on critical surfaces; the commander decides Fluids Type I thin, de-icing; Type II and IV thickened, anti-icing, shear off; IV longest Best holdover Neat thickened fluid, cold ; dilution and heat shorten protectionHot fluid spray 70 °C , 100 psi , nozzle close; never overheat (gel)Neat fluid heating 60 °C max , for sprayabilityHot water Water ≤ 95 °C ; OAT not below −7 °C ; step 2 within 3 min Holdover starts One-step: start of treatment; two-step: start of step 2 Engines running Engines and APU may run, bleeds closed ; flashpoint 139–156 °C
Treat at the latest possible time , treat the areas the pilot can see first (they freeze first), and do not take off without positive evidence of a clean aircraft.
Chapter 15 · Ground De-icing and Anti-icing
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the rules. The clean aircraft concept: no frost, ice or snow on critical surfaces, and the commander makes the final call. Type one fluid is thin and used for de-icing; Types two and four are thickened anti-icing fluids that shear off on take-off, and Type four lasts longest. The longest holdover comes from neat thickened fluid applied cold; water and heat shorten it. Hot fluid is sprayed at seventy degrees and one hundred p s i, and must never be overheated in the rig or it gels. Neat fluid may be warmed to sixty degrees at most for sprayability. Hot water is limited to ninety-five degrees, not below minus seven, with step two within three minutes. Holdover counts from the start of a one-step treatment, or the start of step two. With engines or APU running, the bleeds are closed. Treat as late as possible, treat the areas the pilot can see first, and never take off without positive evidence that the aircraft is clean.