Aircraft Systems · Chapter 14
Ice and Rain Protection What ice and frost do to an aircraft, how ice is detected, and how boots, hot air, electric heat and fluid keep wings, engines, windscreens and propellers clear.
WING
hot bleed air in the double skin
supercooled droplets
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to ice and rain protection. Ice on an aircraft is never harmless: a few millimetres on a wing leading edge, or even a rough coat of frost, can raise the stalling speed and spoil the climb. In this lesson you will see how the crew is warned that ice is forming, and how wings, engines, windscreens, propellers and probes are protected, by rubber boots that crack ice away, by hot air from the engines, by electric heating and by special fluids. We finish with wipers and rain repellent for flying in heavy rain.
Roadmap
Keeping ice and rain off the aircraft 1 · Why it matters Ice and frost change the wing: less C L max, more drag, a higher stalling speed.
2 · Detecting ice Visual cues, ice lights, and detectors that sense ice building up or the conditions for it.
3 · Mechanical de-icing Pneumatic boots inflate in a timed cycle and crack the ice off.
4 · Thermal protection Hot bleed air in the leading edges and intakes; electric heater mats.
5 · Fluid systems Freezing point depressant fluid weeps from porous panels or a propeller slinger ring.
6 · Screens, props, probes Heated windscreens, wipers and rain repellent, propeller heaters and probe heat.
Chapter 14 · Ice and Rain Protection
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this lesson. First, why ice protection matters at all: we will put numbers on what ice and even a thin coat of frost do to the maximum lift coefficient, the drag and the stalling speed. Second, how the crew knows ice is forming, from simple visual cues and ice lights to detectors that sense the ice itself or the conditions that cause it. Then we look at the three ways of protecting the airframe: mechanical boots that crack ice away, thermal systems using hot engine bleed air or electric heating, and fluid systems that stop ice sticking. Finally we cover windscreens, with their heating, wipers and rain repellent, and the protection of propellers and the small probes that feed the instruments.
Why it matters
What ice and frost do to the wing Ice on the leading edge changes the shape : big drag rise and a large loss of CL max Frost leaves the shape alone but makes the surface rough : more skin friction, a weaker boundary layer Both make the wing stall early , at a lower angle of attack and a higher speed Heavy hard frost: CL max falls enough to raise the stalling speed 5 to 10 % More drag and weight mean more power required ; landing speed goes up too
0 8 16 24
0 0.8 1.6
angle of attack (degrees)
lift coefficient
clean · CL max 1.6
hard frost · 1.32
leading-edge ice · 1.0
illustrative wing; frost case = stalling speed +10 %
Chapter 14 · Ice and Rain Protection
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Any ice or frost on a wing makes it worse, never better. Ice on the leading edge changes the actual shape of the aerofoil. The airflow meets lumps and horns instead of a smooth curve, so drag rises sharply and the maximum lift coefficient falls a long way. Frost is more subtle. It leaves the shape alone but makes the surface rough, which increases skin friction and robs the boundary layer of energy. A tired boundary layer separates sooner, so the wing stalls early, at a lower angle of attack and therefore a higher speed. Watch the iced section: as the angle increases, the flow breaks away much earlier than on a clean wing. A heavy coat of hard frost can raise the stalling speed by five to ten per cent, and the extra drag and weight mean more power is needed and the landing speed goes up.
Worked example
Frost and the take-off: no margin left Lift-off speed is about 1.05 to 1.25 VS , so lift-off CL is 90 to 65 % of CL max Lift ∝ V², so CL needed = CL max ÷ (V/VS )²: at 1.10 VS it is 83 % Frost raising VS by 10 % cuts CL max to 1 ÷ 1.1² = 83 % : the wing is at the stall as it lifts off Drag hardly changes on the ground run, so acceleration looks normal : the trap appears only at rotation Rule: no ice, frost or snow may remain on the wings at take-off
Lift coefficient, as % of the clean CL max
clean wing CL max 100 % frosted CL max (+10 % VS ) 83 % needed at 1.10 VS 83 % needed at 1.25 VS 64 %
frosted stall: zero margin at 1.10 VS
Chapter 14 · Ice and Rain Protection
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put numbers on the frost problem. An aircraft typically lifts off at about one point zero five to one point two five times its stalling speed. Because lift goes with the square of speed, the lift coefficient needed at lift-off is the maximum lift coefficient divided by that ratio squared. At one point one times the stalling speed, one point one squared is one point two one, so the wing needs about eighty-three per cent of its clean maximum. Now add hard frost that raises the stalling speed by ten per cent. The frosted maximum is also one over one point two one, about eighty-three per cent. The wing is at the stall the moment it leaves the ground. Worse, frost hardly changes the drag on the ground run, so the acceleration looks perfectly normal. The danger only shows at rotation, which is why nothing may be left on the wings at take-off.
Where ice forms
The places that catch ice first Icing in flight comes from supercooled water droplets freezing on forward-facing surfaces Small, thin objects have a higher catch efficiency : probes, aerials, wiper arms and thin tail edges ice firstProtected areas: wing and tail leading edges , slats, engine intakes , propellers, windscreens and probes Also: inlet guide vanes, oil-cooler and ram-air intakes, aerials, waste-water drain masts A small object gets a relatively bigger change of shape from the same ice
windscreen probes wing leading edge / slats engine intake lips tail leading edges
blue: airframe · orange: heated items
Chapter 14 · Ice and Rain Protection
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
In flight, airframe ice comes mainly from supercooled water droplets, liquid water below zero, which freeze as they hit forward-facing surfaces. Small, thin objects collect droplets much more efficiently than big blunt ones, because the droplets cannot follow the airflow round them. So probes, aerials, wiper arms and thin tail leading edges ice up first, and the same thickness of ice changes their shape far more. That is why the protected areas are the wing leading edges and slats, the tail leading edges, the engine intakes, propellers, windscreens and the probes for pitot pressure, angle of attack and air temperature. Engines may also need protection for the inlet guide vanes, and smaller ram-air intakes, aerials and waste-water drain masts are often heated too.
The physics
Will it freeze? The skin heat balance
Heat in (+) Heat out (−)
kinetic heating by the air kinetic heating by the droplets latent heat of fusion as drops freeze
evaporation convection (cold air flowing past)
Resulting skin temperature
below 0 °C: all drops freeze
at 0 °C: some freeze, some run back
above 0 °C: none freeze
No airframe icing above
≈ 40 000 ft (12 000 m)
cloud is all ice crystals there;
dry crystals bounce off and do not stick
Speed warms the skin, so the speed range with no icing depends on the free water content, the temperature and the altitude.
Chapter 14 · Ice and Rain Protection
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whether a droplet freezes depends on the temperature of the skin it hits, and that comes from a heat balance. Three things add heat: kinetic heating as the air is brought to rest on the leading edge, the kinetic energy of the droplets themselves, and the latent heat released as water turns to ice. Two things remove heat: evaporation and convection into the cold air flowing past. If the result is below zero, every drop freezes. If it is above zero, none do. At zero degrees some freeze and some run back, so the rate of icing and the catch rate are not simply related. Because speed warms the skin, there is a speed above which there is no icing hazard, and it depends on the free water content, temperature and altitude. Above about forty thousand feet, or twelve thousand metres, cloud is all ice crystals, which do not stick, so airframe icing does not occur.
Two philosophies, three methods
Anti-icing or de-icing? Anti-icing prevents any ice forming: continuous heat or fluid. De-icing lets a little ice build, then removes it: intermittent fluid, heat or mechanical effort.
Method How it works Anti- or de-icing Typical use Pneumatic (mechanical) Rubber boots inflate and crack the ice off De-icing Wings and tail of piston twins and turboprops Thermal: hot air Engine compressor bleed (or heat exchanger, combustion heater) warms the leading edge Usually anti-icing Jet wings, slats, engine intakes Thermal: electric Resistance elements in mats or glass Either (continuous or cycled) Propellers , windscreens, probes, turboprop intakesThermal: oil Hot engine oil circulated behind a surface Anti-icing Some intake parts, oil-cooler areas Fluid (FPD) Freezing point depressant fluid spread over the surface Either Leading edges (weeping wing), props, windscreens Detection Detectors relay a warning; may start the systems — Crew warning, auto mode
Chapter 14 · Ice and Rain Protection
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two different philosophies. Anti-icing aims to stop any ice forming at all, so it needs a continuous supply of heat or fluid. De-icing accepts that some ice will build up and then removes it from time to time, with intermittent heat, fluid or mechanical effort. Now the methods. Pneumatic, or mechanical, protection uses rubber boots that inflate and crack ice off; it is always de-icing, and it is found on piston twins and turboprops. Thermal protection uses heat. Hot air, mostly engine compressor bleed, is the standard anti-icing method for jet wings, slats and engine intakes. Electric elements heat propellers, windscreens, probes and some turboprop intakes, either continuously or in cycles. Some systems use hot oil. Fluid systems spread a freezing point depressant over the surface. On top of all these, detectors warn the crew and can switch systems on automatically.
Ice detection
How the crew knows ice is forming Visual cues Ice on wiper arms, windscreen frames, aerials and leading edges. The first and often the best indicator.
Ice inspection lights Two lights on the fuselage sides illuminate the wing leading edges. At night they may be the only aid.
Visual detector mast A small aerofoil mast in view of the pilot, with a light and a heater: ice on the mast shows ice on the aircraft.
Accretion detectors Sense ice actually building up: pressure probe, rotating serrated rotor, vibrating probe.
Inferential detector Senses the conditions, moisture plus a temperature below freezing, not the ice itself.
The warning Usually an amber caution, perhaps a chime; in AUTO it can start anti-icing. Boots still wait for the right ice depth.
Chapter 14 · Ice and Rain Protection
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does the crew know that ice is forming? The first clue is usually visual: ice on the wiper arms, the windscreen frames, aerials or the leading edges. At night many aircraft have two ice inspection lights on the sides of the fuselage that shine on the wing leading edges, and on some types they are the only aid to detection. A simple visual detector is a small aerofoil-shaped mast in view of the pilot, with a light for night and a heater to clear it. Automatic detectors fall into two families. Accretion detectors sense ice actually building up on a probe. The inferential type senses the conditions for icing, moisture together with a temperature below freezing, and infers that ice will form. The warning is usually an amber caution light, and in an automatic mode it can switch on the anti-icing; boots, however, still wait until enough ice has built up.
Accretion detectors 1
The pressure probe and the serrated rotor Pressure-type probe : a hollow tube with four holes in front, two behind Normally ram air keeps a positive pressure inside; ice blocks the front holes, the pressure goes negative and a relay gives the warning Rotor-type detector : a serrated rotor driven by a motor turns beside a fixed knife-edge cutter (gap under 0.002 in)Ice on the rotor is shaved by the cutter: more torque twists the motor on its mounts and trips a microswitch Both have heaters to clear the ice; the rotor warning stays on while ice fouls the cutter
Pressure probe
Serrated rotor
airflow
relay unit
ice blocks the 4 front holes: pressure inside goes negative → ice warning
cutter
motor
µ-switch
ice on the rotor is shaved off: more torque twists the motor on its flexible mounting → microswitch: warning or auto start of anti-icing
Chapter 14 · Ice and Rain Protection
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two older accretion detectors work on simple mechanical ideas. The pressure-type probe is a hollow tube sticking into the airflow, with four holes in its front face and two in the back. In normal flight, ram air through the front holes keeps a positive pressure inside, sensed by a relay unit at the base. When ice blocks the front holes, the pressure inside goes negative and the relay gives the warning. A heater around the tube then clears the ice. The rotor-type detector has a serrated rotor, turned continuously by an electric motor, running beside a fixed knife-edge cutter with a gap of less than two thousandths of an inch. Ice builds on the rotor and the cutter shaves it off, which needs more torque. The motor twists slightly on its flexible mountings and trips a microswitch, giving the warning or starting the anti-icing. The warning stays on as long as ice keeps fouling the cutter.
Accretion detectors 2
The vibrating-probe detector A short probe is vibrated along its axis at its resonant frequency, about 35 to 40 kHz Ice on the probe adds mass , so the resonant frequency falls At a set drop in frequency: ice warning , and the probe heater switches on to shed the ice Heater off after about 6 seconds ; the cycle starts again How often it cycles shows the rate of ice accretion
vibrator housing
probe vibrates axially
warning trip point
≈ 40 kHz, clean
heater ≈ 6 s
time → (ice builds: frequency falls)
frequency
Chapter 14 · Ice and Rain Protection
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The vibrating-probe detector is the one you will meet on most modern aircraft. A short cylindrical probe sticks into the airflow, mounted on a housing that vibrates it along its axis at its natural, resonant frequency, about thirty-five to forty kilohertz. Watch the gauge. When ice builds on the probe, it adds mass, and a heavier probe resonates more slowly, so the frequency falls. When it has fallen to a set trip point, the unit gives an ice warning, and the same signal switches on a heater inside the probe to shed the ice. After about six seconds the heater switches off, the frequency recovers and the cycle begins again. The faster the cycles come, the faster ice is accreting, so counting them can give the crew a rate of icing. Remember the exam point: frequency decreases as ice builds up.
Detecting the conditions
Inferential and beta-particle detectors Inferential detector senses moisture and temperature separately: it detects icing conditions , not iceTwo heated sensing bulbs: the front one gets wet , the rear one is shielded dry ; the wet bulb cools faster A set temperature difference = free water present; a thermal switch lets the warning through only below freezing Beta-particle probe: an emitter and a detector; ice absorbs the particles, so the count fallsCount equal to about 0.4 mm of ice : warning (e.g. caution message and single chime)
Inferential
Beta particle
wet bulb
dry bulb
moisture controller ΔT wet vs dry
thermal switch: below 0 °C?
ICE warning
water AND freezing → warning above 0 °C: no warning, even if wet
forward fuselage skin
emitter detector
airflow
ice absorbs beta particles: fewer reach the detector count for ≈ 0.4 mm ice → warning + chime
Chapter 14 · Ice and Rain Protection
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every detector so far senses ice that has actually formed. The inferential type is different: it detects the conditions for icing. Ice needs two things, liquid water and a temperature below freezing, and this unit senses them separately. Two heated sensing bulbs sit in the airflow, one behind the other. The front bulb gets wet, while the rear one is shielded and stays dry. A wet bulb loses heat faster, so when the temperature difference between them reaches a set value, the controller knows there is free water. A separate thermal switch, exposed to the outside air, only lets the warning through when the temperature is below freezing. The beta-particle detector uses two probes on the forward fuselage. One emits beta particles and the other counts them. Ice on the emitter absorbs particles, so the count falls, and at a count equal to about nought point four millimetres of ice the crew gets a warning.
Operating rules
When to switch the systems on Engine anti-ice: when the IOAT is +10 °C or below and there is visible moisture Engine icing can occur above 0 °C : intake air expands, cools and drops its pressure Airframe protection: at the onset of icing, seen or detectedAnti-icing should be on before ice builds; boots wait for a specified ice depth Ice warnings: an amber caution ; in AUTO , systems may start themselves
Engine anti-ice
IOAT ≤ +10 °C AND visible moisture
cloud, fog with poor visibility, rain, snow, sleet
Airframe anti-ice (hot air, heat)
on at the first sign of icing
leading edges, aerials, wipers or the detector
Pneumatic boots (de-icing)
wait for the specified ice depth
too thin and the ice flexes with the boot
instead of cracking off
Chapter 14 · Ice and Rain Protection
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
When should the crew switch protection on? For the engines, the general rule is to select engine anti-ice whenever the indicated outside air temperature is plus ten degrees or below and there is visible moisture: cloud, fog, rain, snow or sleet. Why so warm? Because air accelerating into the intake expands and cools, so the intake can ice at outside temperatures above zero. For the airframe, protection is generally applied at the onset of icing, when ice is seen on leading edges, aerials or wipers, or when the detector warns. Anti-icing systems work best switched on before ice has built up. Boots are the exception. They must not be cycled until a specified depth of ice has formed, because very thin ice tends to flex with the rubber instead of cracking off. Ice warnings are usually an amber caution, and some systems in an automatic mode will start the protection themselves.
Mechanical de-icing
Pneumatic de-icer boots Used on piston twins and turboprops , on wing and tail leading edges Layers of natural rubber and rubberised fabric enclosing flat inflatable tubes of rubberised fabric Tubes run spanwise on some boots, chordwise on others Outer surface has a conductive coating to bleed off static Fixed by screw fasteners (rivnuts ) or cemented to the leading edge Boot on a leading edge (section) outer rubber layer, conductive coating flat tubes of rubberised fabric wing structure OFF: vacuum holds it flat ON: tubes inflate smooth profile: minimum drag ice cracks and blows away aft
Chapter 14 · Ice and Rain Protection
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pneumatic de-icing is used on piston-engined twins and on turboprops, and it is still the usual way to protect the wings and tail of a modern turboprop. The de-icer boot, or overshoe, is built from layers of natural rubber and rubberised fabric, and between them lie flat inflatable tubes, also made of rubberised fabric and vulcanised inside the rubber. On some boots the tubes run along the span, on others along the chord. Short flexible hoses connect the tubes to the air supply pipes. The outside of the boot carries a thin conductive coating so that static electricity can bleed away instead of building up on the rubber. A boot is either held on by screw fasteners called rivnuts or cemented straight to the leading edge. When the system is off, vacuum holds the boot flat against the leading edge for minimum drag; when it operates, the tubes inflate and the ice cracks off.
Mechanical de-icing
Inflate, crack, deflate: the boot cycle Air from an engine compressor tapping (turboprops), the pressure side of a vacuum pump , or an HP reservoir Inflation breaks the bond between ice and rubber; the airflow carries the ice awayThen air is dumped and the tubes are sucked flat by vacuum (pump, or an ejector venturi ) Distribution by solenoid valves or a motor-driven valve, timed electronically Off : vacuum holds all boots flat, to minimise drag1 · ice builds airflow 2 · inflate: ice cracks airflow 3 · vacuum: flat again airflow Pressure: compressor tapping, vacuum-pump outlet or HP bottle Vacuum: pump inlet or an ejector venturi Timer: electronic , valves solenoid or motor driven Off: vacuum holds the boots flat
Chapter 14 · Ice and Rain Protection
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the cycle in motion. The tubes are inflated with air from one of three sources: on turboprops, a tapping from an engine compressor stage; on piston aircraft, the pressure side of an engine-driven vacuum pump; or a high-pressure reservoir. As the tubes inflate, the rubber stretches and breaks the bond between the ice and the boot, and the cracked ice is carried away by the airflow. At the end of the inflation stage the air is dumped overboard and the tubes are sucked fully flat by vacuum, from the inlet side of the vacuum pump or, with compressor air, from the venturi of an ejector. The pressure and vacuum are applied in a sequence timed by an electronic controller, through solenoid valves or a motor-driven distributor. And when the system is switched off, vacuum is applied continuously to hold every boot flat against the leading edge, keeping drag to a minimum.
Boot timing
Same cycle, different wait
LIGHT icing: 34 s cycle + 206 s dwell = one cycle every 4 minutes dwell 206 s dwell 206 s
HEAVY icing: 34 s cycle + 26 s dwell = one cycle every minute
0 min 1 min 2 min 3 min 4 min 5 min 6 min 7 min 8 min
Group 1: inboard wing boots (both sides)
Group 2: outboard wing boots
Group 3: fin and tailplane
The selector only changes the dwell : the 34-second inflation cycle never changes. Left and right boots always inflate together .
Boots are cycled in symmetrical groups so lift is lost equally on both wings and the demand on the air supply stays small.
Chapter 14 · Ice and Rain Protection
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a typical system the boots are split into three groups. Group one is the inboard boots on both wings, group two the outboard boots on both wings, and group three the fin and tailplane. Left and right always inflate together, so any change of lift is symmetrical. One complete cycle, inflating the three groups in turn, takes thirty-four seconds, and that never changes. What the crew selects is the waiting time, or dwell, between cycles. For light icing the dwell is two hundred and six seconds, so with the thirty-four-second cycle the boots work once every four minutes. For heavy icing the dwell is only twenty-six seconds, so they work once a minute. The longer wait in light icing lets the ice reach a thickness that will crack off cleanly, while heavy icing needs it cleared more often.
Thermal anti-icing
Hot bleed air in the leading edge Jets: compressor bleed air is ducted to the wing leading edges and slats , and the tail on some types A second inner skin forms a narrow gap; hot air in the gap heats the outer skin and leaves through exhaust outlets or the tips Leading-edge flaps (Krueger) are usually not heated Needs large volumes of hot air: costs thrust and fuel, and raises EGT/JPT Temperature held by sensors and valves ; overheat warnings; often locked out on the ground (TEST position) Leading edge with a double skin piccolo tube (runs spanwise) outer skin heated by air in the gap inner skin exhaust vent Typical: slats and wing leading edges, NOT Krueger flaps valves and duct sensors hold the temperature; overheat lights
Chapter 14 · Ice and Rain Protection
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
On jet transports the wings are protected by hot air, so this is called thermal anti-icing. Air is bled from an engine compressor stage and ducted along the wing leading edge, usually to the leading-edge slats and, on some types, to the tail. Inside the leading edge a second, inner skin forms a narrow gap behind the outer skin. Hot air is sprayed from a perforated piccolo tube, flows through the gap, heating the outer skin enough to melt ice and stop more forming, and then leaves through vents or the wing tips. Note the detail the exam likes: slats are heated, but leading-edge flaps such as Krueger flaps usually are not. These systems need large volumes of hot air, which costs thrust and fuel and raises the exhaust gas or jet pipe temperature. Sensors and valves hold the duct temperature within limits, with overheat warnings, and on many aircraft the valves are locked out on the ground except for a test position.
Engine protection
Engine intake anti-icing A gas turbine is very sensitive: ice on the intake lip , nose bullet and inlet guide vanes restricts airflow Ice breaking off is ingested and can damage the compressor; it may even cause a flame-out Hot compressor air flows through the intake cowl lip, the IGVs and sometimes the bullet, then into the intake or overboard Valves are switched from the flight deck; usually no temperature control Effects: slight thrust loss and a rise in JPT/EGT for the same thrust
compressor
bleed from a compressor stage heated: intake lip, inlet guide vanes, nose bullet air then exhausted into the intake (or overboard)
lip bullet IGVs
Chapter 14 · Ice and Rain Protection
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
A gas turbine engine has a serious icing problem. Ice on the intake lip, the nose bullet and the inlet guide vanes restricts the airflow and costs performance, and when it breaks away it is swallowed by the compressor and can damage the blades or even put the engine out. So the intake is protected with hot air bled from the compressor. It is piped forward into the hollow intake cowl lip, through the inlet guide vanes and, on some engines, the nose bullet. After circulating, the air is exhausted overboard or simply into the intake. The valves are switched from a flight-deck panel, and usually there is no separate temperature control. Taking air from the compressor means a small loss of thrust and a rise in jet pipe or exhaust gas temperature for the same thrust, which is why the exam says bleed-air anti-icing increases J P T.
Thermal systems
Sources of hot air and how they are controlled Source How the air is heated Temperature control Compressor bleed (jets)Tapped from a compressor stage, mixed with cooler air in a mixing chamber Duct sensors drive valves in the supply; resistance sensors, temperature switches, overheat lights Exhaust heat exchanger (turboprops)Exhaust gas passes round tubes carrying outside air Flaps and valves moved by an electric actuator and a duct sensor; thermal switchesCombustion heater Fuel/air burned in a sealed chamber; ram air flows through a jacket around it Thermal cycling switches cut the heater fuel at a set maximumEngine intake hot airCompressor air through lip, IGVs, bullet On/off valves from the flight deck; usually no temperature control On the ground Wing valves often disabled by landing-gear relays Can be operated for checks with the switch held at TEST
A thermal system can be anti-icing or de-icing, depending on how long and how hot the air is applied. Bleed-air systems are normally anti-icing.
Chapter 14 · Ice and Rain Protection
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Hot air can be produced in three ways. The usual one on jets is compressor bleed: air tapped from a compressor stage, mixed with cooler air in a mixing chamber and fed into the ducts, with safety shut-off valves to keep the flow and pressure within what the ducts can take. Its temperature is held by sensors in the leading-edge ducts that drive valves in the supply, with temperature indications and overheat lights. Some turboprops use an exhaust heat exchanger, where hot exhaust gas passes round tubes carrying outside air, controlled by flaps and valves. Older aircraft used a combustion heater, burning fuel in a sealed chamber with ram air flowing round it; thermal switches shut off its fuel at a set maximum. Engine intake systems are simple on-off valves with no temperature control. And because hot air on a stationary wing could overheat it, wing valves are often disabled on the ground and checked with the switch held to test.
Thermal: electrical
Electric heater mats Resistance-wire or sprayed-metal elements, sandwiched in glass cloth and resin (or rubber), bonded on Continuously heated strips = anti-icing (parting strips); intermittently heated areas = de-icing A cyclic time switch feeds the intermittent elements and the propeller elements Example turboprop intake: FAST = 2-minute cycle (−6 to +10 °C); SLOW = 6-minute cycle (below −6 °C) Advantage: no effect on the airflow ; drawback: high electrical load
Heater mat (overshoe)
continuously heated parting strip: ANTI-ICING intermittently heated areas: DE-ICING (cyclic timer)
FAST
SLOW
2-minute cycle: OAT −6 to +10 °C 6-minute cycle: OAT below −6 °C
orange = heat on (on/off split varies by type)
0 min 2 min 4 min 6 min 8 min 10 min 12 min
Chapter 14 · Ice and Rain Protection
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Electrical heating uses resistance wire or sprayed-metal elements bonded to the surface. On a widely used turboprop installation they are formed into an overshoe round the intake cowl lip and the oil-cooler intake, with the elements sandwiched between layers of resin-impregnated glass cloth, or sometimes rubber, under an erosion-resistant outer surface. Both techniques are used together. A narrow strip, fed continuously, is anti-icing: it is a parting strip that splits the ice into separate pieces. The larger areas either side are heated intermittently, which is de-icing, through a cyclic time switch that also controls the propeller elements. In this example, fast gives a complete heat-on, heat-off cycle of two minutes between minus six and plus ten degrees, and slow gives a six-minute cycle below minus six. Electric heat leaves the airflow undisturbed, but it needs a lot of electrical power, which is why it is cycled.
Fluid systems
Freezing point depressant fluid: the weeping wing FPD fluid is pumped from a tank to porous distributors on the leading edges; the airflow spreads it backFluid mixes with water, lowers its freezing point and stops ice sticking Panel distributors: porous outer panel, micro-porous sheet, back plate; efficient but need single curvature Strip distributors for double-curved parts such as the fin ; fed in seriesPump has a relief device; works as anti-icing or de-icing , in the air or on the ground
FPD tank
pump
L wing panels R wing panels tail filter + relief
panel distributor (section)
back plate · cavity · micro-porous sheet · porous outer panel metering tube
Chapter 14 · Ice and Rain Protection
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fluid systems stop ice sticking by covering the surface with a freezing point depressant, a glycol or alcohol-based fluid. It is pumped from a storage tank, through a filter, to distributors set into the leading edges, and the airflow carries it back over the surface. Where it mixes with water it lowers the freezing point, so ice cannot bond. There are two kinds of distributor. Panel distributors cover a large area of leading edge and are the more efficient and economical, but they only suit surfaces curved in one direction. Fluid enters through a metering tube into a cavity behind a micro-porous sheet and seeps out through the porous outer panel. Double-curved parts such as the fin use strip distributors, fed in series. The pump has a relief device that reduces flow if a pipe blocks. Because fluid can prevent ice or loosen ice already there, this integral system works as anti-icing or de-icing, in the air or on the ground.
Windscreen protection
The electrically heated windscreen A laminated screen: glass plies and a vinyl interlayer , with a transparent conductive film heated by AC Heating prevents ice and mist and keeps the vinyl elastic , improving bird-strike (impact) resistance at low temperature Two sensors in the screen: one controls a constant temperature, one gives overheat protection Overheat: power off and warning light (some lock out until switched OFF and ON) Warm up slowly to avoid thermal shock ; high power setting for severe icing; reduced voltage on the ground
Laminated windscreen (exploded)
outer glass ply (outside) conductive film: heater vinyl interlayer structural glass ply vinyl interlayer structural glass ply (inside)
control sensor overheat sensor
temperature controller constant temperature · NORMAL / HIGH
OVHT power cut
Slow warm-up: no thermal shock. Overheat: vinyl bubbles, discolours, permanent damage. Warm vinyl = better impact strength.
Chapter 14 · Ice and Rain Protection
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The pilots’ windscreens are a laminated sandwich of glass plies bonded with vinyl interlayers. On or near the outer ply is a transparent conductive film, and an alternating current through it heats the glass. Heating does two jobs. It prevents ice and mist, and, just as important, it keeps the vinyl warm and elastic, which greatly improves the screen’s resistance to a bird strike at low temperatures. That is why the heat is usually on for the whole flight. Two sensing elements, fine wire grids whose resistance rises with temperature, are laminated into the screen: one controls the heat to hold a constant temperature, the other gives overheat protection, because overheated vinyl bubbles and discolours permanently. On overheat the power is cut and a warning light comes on. Heat must be applied slowly to avoid thermal shock, a high-power setting copes with severe icing, and on the ground a reduced voltage is used.
Rain protection
Wipers, washers and rain repellent Wipers Independent, two-speed, electric or hydraulic, with a park position. The main way to clear heavy rain . Never run them on a dry screen.
Washers About a gallon of washer fluid pumped to spray nozzles, used with the wipers to clean the screens.
Rain repellent One press sprays for about ⅓ s , however long it is held; lasts 2 to 5 min ; about 75 shots per can. Used with the wipers in heavy rain.
Repellent cautions On a dry screen it reduces visibility . Sight gauge float and a go/no-go pressure gauge show when the can is empty.
Fluid de-icing Older types spray a methyl-alcohol based fluid onto the screen, from a tank with hand or electric pumps.
Demisting Warm cabin air blown on the inside of the screen keeps it clear of mist .
Add-on heated panel Light aircraft may have a small heated glass panel fitted in front of the windscreen.
Exam point In heavy rain the screen is kept clear by the wipers ; repellent only helps them, it does not replace them.
Chapter 14 · Ice and Rain Protection
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Rain is a visibility problem rather than an icing one, and the main tool is the wiper. Each pilot normally has an independent two-speed wiper, electrically or hydraulically driven, with a park position; they must not be run on a dry screen because they scratch it. Washers spray fluid from a reservoir of about a gallon to clean the screens with the wipers. In heavy rain, rain repellent helps the wipers: each press of the button opens the valve for about a third of a second however long you hold it, one shot lasts two to five minutes, and a full can gives about seventy-five applications. Sprayed on a dry screen it smears and reduces visibility. A sight gauge float and a pressure gauge show when the can is empty. Some older aircraft spray a methyl-alcohol fluid on the screen to de-ice it, warm cabin air demists the inside, and light aircraft may carry a small add-on heated panel.
Propeller protection
Keeping ice off the propeller Ice distorts the blade section: loss of efficiency , imbalance and destructive vibration Fluid (anti-icing): pumped at about 10 psi to a slinger ring on the hub, flung along the blades by centrifugal forceElectrical (de-icing): heater elements on the blade roots (the inner third at least, sometimes a mid section), and the spinner Power via slip rings and brushes ; a cyclic timer heats blades in sequence, one propeller at a time ; thin ice is flung off Use only with the propellers turning , or the elements overheat
inner third: always heated mid section on some props spinner heated
cyclic timer heats blades in turn
slip rings + brush block only with props turning
Fluid system
tank + pump
slinger ring ≈ 10 psi to blade roots centrifugal spreading
Chapter 14 · Ice and Rain Protection
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ice on a propeller distorts the blade sections, so the propeller loses efficiency, and because it rarely forms or sheds evenly it causes imbalance and destructive vibration. There are two systems. A fluid system is anti-icing: freezing point depressant is pumped at about ten p s i into a slinger ring on the back of the hub, and centrifugal force flings it along the blade roots, sometimes guided by grooved rubber overshoes. The usual modern system is electrical de-icing. Heater elements are bonded to the inner part of each blade, always the inner third and on some propellers a mid section too, and on turboprops to the spinner. Power reaches the turning propeller through brushes running on slip rings. A cyclic timer heats the blades in sequence, and on a twin one propeller at a time, to limit the electrical load: a thin film of ice builds, insulates the surface as the element warms it, and is flung off by centrifugal force. The heaters must only be used with the propellers turning, or the elements will overheat.
Small but critical
Probes, drains, aerials and fuel Air-data probes Pitot heads , static ports on some types, alpha (AoA) vanes , TAT probes: electrically heated. Ice here corrupts airspeed, altitude and EPR.
Engine and feel probes P1 engine inlet pressure probes and Q-feel probes for artificial feel are heated too.
Drains and water lines Waste-water drain masts and potable water lines (in-line heaters) would otherwise freeze and block.
Aerials and intakes Some aerials , large fences, oil-cooler and ram-air intakes (generator cooling, bay ventilation).
Fuel icing Water in fuel freezes into crystals that block filters : fuel heaters (compressor air or oil) warm the fuel before the filter.
Fuel freezing points Jet A-1: −47 °C . Jet A: −40 °C . Long cold cruises can chill tank fuel towards these limits.
Heat on the ground Probe heaters run hot in still air: many are powered at reduced level or only with engines running.
Inspection lights Wing ice lights let the crew check leading edges at night, often the only check.
Chapter 14 · Ice and Rain Protection
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Finally, the small items. Air-data probes are electrically heated: pitot heads, the angle-of-attack or alpha vanes, total air temperature probes, and on some aircraft the static ports. A frozen pitot probe corrupts airspeed, and ice on other probes can corrupt altitude and engine pressure ratio, which in turn misleads autopilots and autothrottles. Engine inlet pressure probes, called P1 probes, and the Q-feel probes that give artificial feel are heated too, as are waste-water drain masts and in-line heaters on water pipes. Some aerials and oil-cooler and ram-air intakes are protected. Fuel can ice as well: water in it freezes into crystals that block filters, so jet engines warm the fuel in an oil cooler or heater before the filter. And know the fuel freezing points: Jet A-1 freezes at minus forty-seven degrees and Jet A at minus forty, which matters on long, cold cruises.
Summary
Ice and rain protection at a glance Area Usual protection Remember Jet wing and slats Hot compressor bleed air in a double skin Anti-icing; not Krueger flaps; raises JPT Turboprop wing and tail Pneumatic boots De-icing; 34 s cycle, dwell varies; vacuum holds flat Jet engine intake Hot compressor air: lip, IGVs, bullet IOAT ≤ +10 °C with visible moisture Propellers Electric elements, cyclic timer (or fluid slinger ring)De-icing; only when turning; slip rings and brushes Windscreen Electric film, constant temperatureAlso bird-strike strength; heat slowly Heavy rain Wipers + rain repellentNo repellent or wipers on a dry screen Detection Vibrating probe, others; ice lights Frequency falls as ice builds
Chapter 14 · Ice and Rain Protection
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. Jet wings and slats are anti-iced with hot compressor bleed air flowing in a double skin; leading-edge Krueger flaps usually are not heated, and the bleed raises jet pipe temperature. Turboprop wings and tails use pneumatic boots, a de-icing system with a fixed thirty-four-second cycle and a selectable dwell, held flat by vacuum when off. Jet intakes are heated by compressor air at the lip, guide vanes and bullet, switched on at plus ten degrees or below in visible moisture. Propellers are de-iced electrically with a cyclic timer, through slip rings and brushes, and only while they turn, or anti-iced by fluid from a slinger ring. Windscreens are heated electrically to a constant temperature, which also improves bird-strike strength. Heavy rain is handled by wipers helped by repellent. And the most common detector is the vibrating probe, whose frequency falls as ice builds.