Aircraft Systems · Chapter 5
Landing Gear What the undercarriage has to do, how oleo struts absorb a landing, how nose wheels castor, steer and resist shimmy, and how gear is retracted, locked, indicated and lowered in an emergency.
WING STRUCTURE · MAIN GEAR TRUNNION
side stay
retraction jack
oleo strut
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter five is about the landing gear, often called the undercarriage. In the air it is just dead weight, but on the ground it does everything: it carries the aeroplane, lets you steer it, and on every landing it has to soak up a huge amount of energy in a fraction of a second. We will look at how gear legs are laid out and what loads they carry, how an oleo-pneumatic strut works, how the nose wheel castors, steers and is kept from shimmying, and then how retractable gear is raised, locked, shown to the crew, protected against mistakes and lowered when the normal system fails.
Chapter 5 roadmap
From a fixed leg to a retracting airliner gear 1 · What gear must do Functions, fixed gear types, tricycle versus tailwheel, design factors and the loads a leg must carry.
2 · Shock absorbing The oleo-pneumatic strut : nitrogen as the spring, oil through an orifice as the damper; servicing faults.
3 · Wheels on legs Twin, fork, half fork, cantilever; bogies , wheel loading, scrubbing and the bogie position light.
4 · The nose gear Castoring, self-centring , powered steering with its bypass, and shimmy : causes and cures.
5 · Retraction Hydraulic sequence with sequence valves and one-way restrictors ; pneumatic and electric systems; locks.
6 · Safety and emergencies Lights, lever lock, ground locks , horn, emergency extension , air/ground logic and slush.
Chapter 5 · Landing Gear
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this chapter. First we ask what a landing gear has to do, and look at the simple fixed gear of light aircraft, the tricycle layout and the loads a gear leg must survive. Second, the heart of almost every gear leg, the oleo-pneumatic strut, where compressed nitrogen acts as the spring and oil forced through an orifice acts as the damper. Third, how wheels are attached to legs, and why big aircraft spread their weight over many wheels on bogies. Fourth, the nose gear: it must castor, centre itself before retraction, steer, and resist a violent wobble called shimmy. Fifth, retraction: we follow a hydraulic system step by step, with its sequence valves, restrictors and locks. Finally, the safety features: lights, the lever lock, ground locks, warning horns, the emergency extension systems and the air and ground logic that so many other systems rely on.
Part 1 · What gear must do
Three jobs, and dead weight in the air Support the aircraft at a convenient height : clearance for propellers, engines and flaps, easy loading Let it be manoeuvred on the ground: taxying, steering, towing Absorb the kinetic energy of landing and control the decelerationOnce airborne it is dead weight , so designers fight for low weight and small stowed volume Ground equipment could do the first two jobs, but nothing else can absorb the landing
clearance
steer and manoeuvre
absorb landing energy
1 Support the aircraft at a convenient height
clearance for propellers, engines and flaps; easy loading
2 Allow it to be manoeuvred on the ground
3 Absorb the kinetic energy of landing
and control the deceleration (brakes)
Chapter 5 · Landing Gear
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A landing gear has three jobs. It holds the aircraft at a convenient height, high enough to clear the propellers, the engines and the flaps, and low enough for easy loading. It lets the aircraft be manoeuvred on the ground, whether taxying under its own power, steering, or being towed. And it absorbs the kinetic energy of the landing, then controls the deceleration through the brakes. The moment the aircraft leaves the ground, though, the gear does nothing useful at all; it is simply dead weight carried for the whole flight. In theory you could replace the first two jobs with equipment on the ground, but nobody has found another way to absorb the energy of a landing. So the gear stays, and an enormous amount of design effort goes into making it as light as possible and as small as possible when it is stowed.
Part 1 · What gear must do
Fixed gear: simple, cheap and draggy Slow, light aircraft accept the drag in return for simplicity, low cost and little maintenance Spring steel leg : a tapered tube or strip bolted to the fuselage, axle at the bottomRubber cord (bungee): tubular struts load several turns of rubber in a loopOleo-pneumatic strut : on some main gears and most fixed nose gears Spats reduce drag but pick up mud on grass: clean them before the next take-offRetractable gear: less drag, but more weight, complexity and maintenance
Spring steel Rubber cord Oleo + spat
fuselage
tapered steel leaf flexes to absorb the landing
cord
turns of rubber cord (bungee) take the load
spat
spat cuts drag, but collects mud on grass strips
Chapter 5 · Landing Gear
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
On slow, light aircraft the gear is often fixed. It costs some performance, because the legs and wheels hang in the airflow, but that drag is a fair price for simplicity, a low purchase price and very little maintenance. There are three common types. A spring steel leg is a tapered tube or strip of spring steel, bolted to the fuselage at the top, with the axle at the bottom; it simply flexes to absorb the landing. Some aircraft use rubber cord, where tubular struts press against several turns of rubber in a loop. And some fixed main gears, and most fixed nose gears, have an oleo-pneumatic strut. Wheel spats are fairings that reduce the drag, but on a grass strip they can fill with mud, adding weight and hurting take-off performance, so they must be removed and cleaned before flying again. Faster aircraft retract the gear, accepting more weight, complexity and maintenance.
Part 1 · What gear must do
The tricycle layout Two main units just aft of the CG carry up to about 90% of the weight and all the initial landing shock The nose unit keeps the aircraft level and usually steers it Advantages over the tailwheel: no tipping onto the nose when taxying in a strong tailwind Much less risk of ground looping , because the CG is ahead of the mains Worked example: wheelbase 12 m, CG 1.2 m ahead of the mains: nose load = 1.2/12 = 10%
Tricycle (nose wheel)
CG
nose ≈ 10%
mains ≈ 90%
mains just aft of the CG take all the initial landing shock
Tailwheel (tail dragger)
CG behind mains
ground loops, can nose over
Chapter 5 · Landing Gear
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Almost every modern aircraft uses the tricycle layout. The two main units sit just behind the centre of gravity, so they carry up to about ninety per cent of the weight and take all of the initial shock of the landing. The nose unit keeps the aircraft level and in most cases provides the steering. You can see the load share in the worked example. With a wheelbase of twelve metres and the centre of gravity one point two metres ahead of the main wheels, the nose carries one point two divided by twelve, which is ten per cent. Compared with the older tailwheel, or tail dragger, layout, the tricycle gear has two big advantages. It cannot tip forward onto its nose when taxying with a strong tailwind behind it, and because the centre of gravity is ahead of the main wheels, it is far less likely to ground loop.
Part 1 · What gear must do
What shapes a gear design Main factors Size, weight and role of the aircraft, high or low wing , performance, and the structure available for stowage .
High-wing freighters Floors near the ground for loading; a wing perhaps 20 ft up is too high for a leg, so the mains go in fuselage pods .
Wing-mounted unit A leg pin-jointed to the structure, wheels, a shock absorber , brakes , and bracing against turning and braking loads.
Fuselage-mounted unit No geometric lock is available, so separate up and down locks are needed; each wheel may need its own shock absorber .
Easy access A fuselage gear can often be reached in flight , allowing manual lowering in an emergency.
Body gear steering Very large aircraft (e.g. B747 ) turn part of the main gear to help in tight turns .
Chapter 5 · Landing Gear
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many factors decide what a landing gear looks like, and the main ones are the size, weight and role of the aircraft, whether it has a high or a low wing, its performance, and how much room the structure leaves for stowing the gear. Multi-role freighters show this well. They need the cabin floor close to the ground for loading, so they have a high wing, but a wing perhaps twenty feet up is far too high for a strong enough leg, so the main gear goes into pods on the fuselage. A wing-mounted main unit is basically a leg pin-jointed to the structure, with its wheels, a shock absorber, brakes, and bracing against turning and braking loads. A fuselage-mounted unit is similar, but it has no geometric lock available, so it needs separate locks up and down, and each wheel may need its own shock absorber. The largest aircraft also steer part of their main gear, called body gear steering.
Part 1 · What gear must do
Five loads on every leg Compression : static weight and the touchdown impactRearward bending : wheel spin-up at touchdown and brakingSide loads : crosswind landings and take-offs, turning while taxyingForward loads : during push-backTorsion : ground manoeuvring and pivotingThe nose gear carries mostly compression, plus shear from the towing attachment
Side view Front view
drag strut
← nose
compression
rearward bending
forward (push-back)
side loads: crosswind, turns
torsion (turning)
Chapter 5 · Landing Gear
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every gear leg, and the structure it is attached to, must survive five kinds of load. Compression is the obvious one: the static weight of the aircraft, plus the much bigger impact load at touchdown. Rearward bending comes from the wheels being spun up from rest at touchdown, and then from braking. Side loads come from crosswind landings and take-offs and from turning while taxying. Forward loads appear during push-back, when the tug pushes the aircraft backwards. And torsion, a twisting load, comes from ground manoeuvring, especially pivoting tightly on one main gear. Because all these loads go into the mountings, the attachment structure must be just as strong as the leg. The nose unit is lighter, as it carries less weight and mainly direct compression, but it also carries the towing attachment, so it must withstand shear loads as well.
Part 2 · Shock absorbing
The oleo-pneumatic strut Outer cylinder fixed to the airframe; inner cylinder slides inside it and carries the axlePartly filled with hydraulic oil , then charged with dry nitrogen (or dry air) Nitrogen is the spring: it carries the weight; commercial aircraft use nitrogen Oil forced through an orifice , its size varied by a tapered metering pin , is the damperTorque (scissor) links stop the inner cylinder turning and limit its extension
Nitrogen the spring
Hydraulic oil the damper
Orifice plate restricts flow
Metering pin varies the gap
Outer cylinder fixed to airframe
Inner cylinder slides, carries axle
Torque links stop the inner cylinder rotating; limit extension
axle
Chapter 5 · Landing Gear
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Nearly every modern gear leg is built around an oleo-pneumatic strut. The outer cylinder is fixed rigidly to the airframe, and an inner cylinder, carrying the axle, slides up and down inside it. The strut is partly filled with hydraulic oil and then charged with compressed gas. On commercial aircraft that gas is dry nitrogen, because it is inert and holds no moisture; dry air is used on some light aircraft. The nitrogen is the spring: it carries the weight of the aircraft. The oil is the damper: as the strut moves, oil is forced through a small orifice, and a tapered metering pin in the orifice changes the size of the gap through the stroke. Watch the strut at touchdown: the landing load drives the inner cylinder up, the oil is squeezed through the orifice into the gas space, and then the strut settles. Torque links, also called scissor links, join the two cylinders so the inner one cannot rotate, and they limit how far it can extend.
Part 2 · Shock absorbing
How the strut works, and what goes wrong Static : gas pressure balances the weight with the strut about mid-stroke Compression : oil through the orifice limits the speed; gas pressure rises to stop the loadExtension : gas pushes the strut out, and the orifice slows the rebound tooSo the oil limits the speed of both compression and extension Low gas (leak): strut sits too low, unequal shiny chrome showing on the two mainsOver-extension : most likely too much gas or fluid in the strut
10 20 30 40 50 60 70
0% 25% 50% 75% 100%
static: about mid-stroke, 24 bar
touchdown: gas squeezed, pressure climbs steeply
fully extended: 15 bar
compression (per cent of usable stroke)
gas pressure (bar)
Chapter 5 · Landing Gear
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the strut through a landing. Standing still, the gas pressure exactly balances the weight, and the inner cylinder sits roughly half way up its stroke. At touchdown the strut shortens; oil must squeeze through the orifice past the metering pin, and that restriction limits how fast the strut can compress. As the volume shrinks, the gas pressure rises, slowly at first and then very steeply, as the graph shows, until it balances the load. Then the gas acts like a spring and pushes the strut out again, but the oil has to flow back through the orifice, so the rebound is slowed as well. That is the exam point: the oil limits the speed of both compression and extension, while the gas carries the weight. If gas leaks out, the strut sits too low, and you see unequal lengths of shiny chrome on the two main legs. If a strut is extended too far, the most likely cause is too much gas or fluid in it.
Part 3 · Wheels on legs
Mounting the wheels: twin, fork, half fork and cantilever
Twin (dual) Fork Half fork Cantilever
two wheels, one axle, leg between leg splits round one wheel
arm down one side only stub axle from the leg
Footprints
single twin tandem
four-wheel bogie
six-wheel bogie
Light aircraft use single wheels on cantilever or fork mountings; airliners use twin nose wheels and twin or bogie main units.
Chapter 5 · Landing Gear
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the four ways of attaching wheels to a leg, seen from the front, from left to right. First, twin wheels: one axle across the bottom of the leg with a wheel on each side; this is the usual airliner nose gear and many main gears. Second, the fork: the leg divides and straddles a single wheel, with the axle supported on both sides, as on many light aircraft nose gears. Third, the half fork: a single arm comes down one side of the wheel to the axle. Fourth, the cantilever: a stub axle sticks straight out from one side of the leg, as on many light aircraft main gears. Learn that order, twin, fork, half fork, cantilever, because exam questions show exactly this kind of sketch. Along the bottom are the footprints you will meet: single, twin, tandem, the four-wheel bogie and the six-wheel bogie found on the largest twin-engined jets.
Part 3 · Wheels on legs
Why big aircraft have many wheels Wheel loading : static load per wheel at take-off weight; high loading damages weak runwaysMany small, low-pressure tyres replace one big high-pressure tyre (B747, B777 and A340: 10 to 18 wheels ) Also: lighter units, easier wheel and brake changes , safety if a tyre bursts, easier stowage Penalty: a big footprint crabs in turns, so tyres scrub and turning radius grows Use the largest practical turning circle , avoid tight turns, roll straight before stopping A truck (bogie) light warns that a bogie is not in the position for retraction
70 t aircraft, 92% on two main legs
1 wheel per leg 32.2 t twin wheels 16.1 t 4-wheel bogie 8.1 t
load per wheel: more wheels, lower tyre pressure, kinder to the runway
Bogie in a tight turn (top view)
turn centre
↑ forward
front axle forced outward
rear axle forced inward: tyres scrub
Chapter 5 · Landing Gear
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
As aircraft grew heavier, the load on each wheel grew too. Wheel loading is the static load on each wheel at take-off weight, and a high wheel loading will damage a runway that is not strong enough. Strengthening very long runways is expensive, so instead the load is spread over many smaller wheels with lower-pressure tyres. The chart shows a seventy tonne aircraft with ninety-two per cent of its weight on two main legs: thirty-two tonnes per wheel with a single wheel, sixteen with twin wheels, and about eight with a four-wheel bogie. Multi-wheel units are also lighter, easier to service, safer if a tyre bursts, and easier to stow. Their big drawback is turning: the bogie crabs, the rear wheels are dragged sideways and the tyres scrub, so use the largest turning circle you can and roll straight for a moment before stopping. On aircraft with tilting bogies, a truck light warns that a bogie is not in the right position for retraction.
Part 4 · The nose gear
Castoring and self-centring Nose gear: lighter, mainly compression , but shear from towing; must castor, centre, steer and resist shimmy Castoring : the wheel trails behind its axis and turns freely in response to differential braking or rudder forcesSelf-centring before retraction is essential: the bay has limited space An off-centre wheel being forced up can cause severe structural damage Centring by a spring-loaded cam inside the strut, or a hydraulic dashpot / steering jacks
Castoring trail Centring cam
contact point behind the steering axis
← travel steering axis
upper cam (fixed)
lower cam (on piston)
strut extends after lift-off: cams mesh, wheel goes straight
Chapter 5 · Landing Gear
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The nose unit is lighter than a main unit and carries mostly compression, but it has the towing attachment, so it must take shear loads too. It has four special requirements: castoring, self-centring, steering and resisting shimmy. Castoring means the wheel trails behind its steering axis, like the wheel of a supermarket trolley, so it swings freely to follow the aircraft when you turn it with differential braking or with the rudder at speed. Self-centring before retraction is essential, because the nose wheel bay has very little spare room. If the wheel were turned and the hydraulics forced it up into the bay, the structure could be badly damaged. A common method is a pair of cams inside the strut. When the strut extends after lift-off, the lower cam on the piston slides into the upper cam and forces the wheel straight. Other aircraft use a hydraulic dashpot, or centre the wheel with the steering jacks themselves.
Part 4 · The nose gear
Nose wheel steering Light aircraft: push-pull rods from the rudder pedals , with spring struts to absorb shocks Large aircraft: hydraulic steering from a tiller (and pedals for small angles) Pressure from the gear DOWN line via a change-over valve: steering only with the gear down Follow-up linkage resets the control valve, holding the selected angleValve neutral: a bypass lets the wheel castor for towing; restrictors damp the motion Up-line pressure to the jacks centres the wheel on retraction; an accumulator gives limited back-up
nose leg
steering jacks
control valve
bypass
change-over valve
from gear DOWN line
accumulator (limited reserve)
tiller
follow-up linkage
Chapter 5 · Landing Gear
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Early aircraft steered only with differential braking. A light aircraft today usually links the nose wheel to the rudder pedals with push-pull rods, through spring struts that let the wheel move up and down without kicking the pedals. Large aircraft need power steering, which lets the engines stay at minimum taxy thrust, saving fuel, brake and tyre wear, and noise. A typical hydraulic system takes its pressure from the gear down line through a change-over valve, so steering works only when the nose gear is down, with an accumulator as a limited emergency supply. Turning the tiller moves a control valve, which sends fluid to two steering jacks that rotate the strut. A follow-up linkage gradually resets the valve, so the wheel stops at the angle you selected. With the valve in neutral, a bypass lets fluid pass from one jack to the other, so the wheel can castor for towing, and restrictors damp the motion. When the gear is selected up, up-line pressure in the jacks centres the wheel.
Part 4 · The nose gear
Nose wheel shimmy A rapid oscillation of the nose wheel about its vertical axis , from the flexible tyre side walls The track becomes a sinusoidal wobble about the intended path Worst at high speed on the ground : vibration through the whole aircraft Made worse by worn or broken torque links , worn wheel bearings and uneven tyre pressures Cured by shimmy dampers (fitted to the nose gear), a hydraulic lock in the steering jack, heavy centring springs, twin wheels or twin-contact tyres
Track of the nose wheel
intended track
actual: rapid, growing sinusoidal oscillation
about the vertical axis
Causes
• worn or broken torque links • worn wheel bearings • uneven tyre pressures
Cures
• shimmy damper / hydraulic lock • heavy centring springs • twin wheels or twin-contact tyre
Chapter 5 · Landing Gear
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Shimmy is a rapid, unstable oscillation of the nose wheel from side to side about its vertical axis. It starts because the tyre side walls are flexible: the contact patch lags behind the wheel, and with the castor trail that lag can feed a growing wobble. If you could trace the wheel track, it would be a wavy, sinusoidal line about the intended straight track. Shimmy is most dangerous at high speed on the ground, on the take-off or landing run, when it can shake the whole aircraft. Worn or broken torque links are the classic cause, because they let the wheel turn independently of the steering; worn wheel bearings and uneven tyre pressures make it worse too. The cures all add damping or stiffness. Light aircraft with a single nose wheel normally use a shimmy damper, a small hydraulic piston that resists rapid movement. Others trap fluid in the steering jack as a hydraulic lock, use heavy centring springs, fit twin nose wheels, or use twin-contact tyres.
Part 5 · Retraction
Retractable gear: what every system needs
Power hydraulic; pneumatic or electric Locks locked up AND locked down Indication lights for every leg Emergency extension if the power source fails Ground protection no retraction on the ground Gear-up landing warning horn when the gear is not down Doors seal the wells for low drag
Retraction is normally hydraulic. On some light aircraft only retraction is powered: the gear free-falls down, helped by springs.
Chapter 5 · Landing Gear
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most transport aircraft, and many light aircraft, retract their gear to improve performance. Watch the airliner as the gear retracts: the doors open, the main gear swings inboard into the belly, the nose gear swings forward, and then the doors close to seal the wells and keep the drag down. Every retractable system needs the same things. A power source, normally hydraulic, although pneumatic and electric systems exist; on some aircraft power is used only for retraction, and the gear falls down by gravity and airflow. Mechanical locks that hold each leg securely both up and down. Indication of where every leg is. A way of lowering the gear if the normal power fails. Protection against retracting the gear while the aircraft is standing on it, and a warning against landing with it still up.
Part 5 · Retraction
A hydraulic retraction circuit
Selector UP / DOWN
UP line DOWN line
NLG downlock
NLG jack
NLG uplock
1-way
restrictor
MLG downlock
MLG jack
SV2
MLG uplock
SV1
Door jack
SV1: opened by MLG fully up
SV2: opened by door fully open
Purple dashed lines: mechanical operation of the sequence valves by the moving gear and door. Red: up line. Blue: down line.
Chapter 5 · Landing Gear
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a simplified hydraulic gear circuit. Pressure normally comes from the engine-driven pumps, with an alternative source if they fail; some light aircraft use a self-contained power pack instead. The selector valve sends pressure to either the up line, along the top, or the down line, along the bottom, and opens the other line to return. The nose gear components are fed directly: its downlock, its jack and its uplock. The main gear side is fed through a one-way restrictor, which lets fluid in freely but restricts fluid coming back. Two sequence valves, drawn in purple, make things happen in the right order. Sequence valve one is opened mechanically when the main gear reaches fully up, and only then lets pressure reach the door jack to close the doors. Sequence valve two is opened when the doors are fully open, and only then lets pressure reach the main uplock and the main jack to lower the gear.
Part 5 · Retraction
The up and down sequences
Gear UP selected
Gear DOWN selected
1 Downlocks release nose and main downlocks unlocked by pressure 2 Legs retract nose jack and main jack; main via restrictor free flow 3 Main gear fully up it opens sequence valve 1 pressure goes to door jack 4 Doors close, locks door jack closes doors; uplocks engage (spring applied)
1 Nose gear down nose uplock releases, nose leg extends against the airflow 2 Main doors open door jack opens doors first; fluid waits at sequence valve 2 3 Doors fully open they open sequence valve 2: main uplock releases 4 Main gear lowers return fluid restricted: damping; downlocks engage, 3 greens
Some aircraft put the selector in neutral after retraction, so the gear is unpressurised in the cruise and held by its uplocks.
Chapter 5 · Landing Gear
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now let us run the sequences. Select gear up. Pressure releases the nose and main downlocks, and the nose jack and main jack raise the legs, the main side fed through the free-flow direction of the restrictor. When the main gear is fully up, it opens sequence valve one, pressure reaches the door jack, and the doors close. The uplocks, which are hydraulically released and spring applied, catch the legs. Some aircraft then put the selector to neutral, so the gear sits unpressurised on its uplocks for the cruise, which extends the life of the components. Now select gear down. The nose uplock releases and the nose gear extends. At the same time the door jack opens the main doors, while fluid for the main gear waits at sequence valve two. Only when the doors are fully open does sequence valve two let pressure release the main uplock and drive the main jack. Its return fluid passes through the restrictor, damping the fall, and finally the downlocks engage.
Part 5 · Retraction
Restrictors and sequence valves One-way restrictor : free flow one way, flow through a small orifice the other wayFitted to slow the extension of the main gear, which gravity would make too fast Protects the gear stops, attachments and mountings from damage The nose gear usually lowers forward, against the airflow , so it needs no restrictor Sequence valve : opened mechanically by a gear leg or door, so actions happen in the right order (doors open before the gear moves)
One-way restrictor
piston with small orifice spring
free flow: piston lifts off its seat
restricted flow: only through the orifice
Sequence valve
gear / door pushes plunger
in (waiting) out to next jack
plunger in: passage opens, next stage starts
Chapter 5 · Landing Gear
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two small valves make a gear system behave. The one-way restrictor lets fluid flow freely in one direction, because a spring-loaded piston lifts off its seat, but in the other direction the fluid can only pass through a small orifice. In the scene the selector is moved to down and the jack lowers the gear. Gravity is pulling the heavy main gear down too, so without help it would fall too fast; the fluid leaving the jack must squeeze through the restrictor, so the gear is lowered at a controlled rate, protecting the stops, attachments and mountings. That is the exam answer: restrictors limit the rate of extension. The nose gear usually lowers forwards, against the airflow, so it rarely needs one. The sequence valve is a spring-loaded plunger. Fluid waits at it until a moving gear leg or door pushes the plunger in and opens the passage. That is how the doors are guaranteed to be open before the gear starts to move.
Part 5 · Retraction
Locking the gear up and down Downlock : an over-centre (geometric) lock: the side stay or drag strut goes just past straightLanding loads then push the joint harder against its stop ; a lock spring holds it Released by a small unlock jack (or the first movement of the retraction jack) Uplock : a hook catches a roller on the leg, spring applied, hydraulically released Collapse on the ground is prevented by the bracing struts and their downlocks , not by the jack
Downlock: over-centre Uplock hook
joint just past the straight line
← lock spring
side stay
unlock jack breaks the joint to start retraction
roller on the gear leg
spring applied, hydraulically released
Chapter 5 · Landing Gear
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Each leg must be locked both down and up. Down, the usual method is a geometric, or over-centre, lock. The side stay or drag strut is made in two halves joined by a hinge. As the gear comes down, the hinge passes just beyond the straight line between the two ends, against a stop, and a lock spring holds it there. Now any load on the leg pushes the joint harder against its stop instead of folding it, so the stay becomes rigid, and the gear cannot collapse. That is why it is the bracing struts and their downlocks, not hydraulic pressure in the jack, that keep the gear standing on the ground. To retract, a small unlock jack, or the first movement of the retraction jack, breaks the joint back over centre. Up, the gear is usually held by a hook that catches a roller on the leg. Uplocks are spring applied and hydraulically released, so they stay locked if pressure is lost.
Part 5 · Retraction
Pneumatic and electric retraction Pneumatic Engine-driven air pumps charge a storage cylinder; a reducing valve feeds the selector. Return air is exhausted to atmosphere at the selector.
Gentle extension A second reducing valve gives a lower pressure for extension , for the same reason hydraulic systems use restrictors: to stop the gear slamming down.
Damped rams The hollow ram rod is filled with oil or grease forced past a fixed damper piston, slowing movement both ways.
Pneumatic locks Downlocks: over-centre drag strut at the end of the stroke. Uplocks: spring rams, released by air pressure . Doors moved by linkage .
Electric Light aircraft: a reversible motor drives a screw jack and torque tube; rods and cables move the legs; rubber cord helps extension.
Limit switches Over-centre downlocks engage with spring help; limit switches cut and brake the motor when locked down and when fully up.
Chapter 5 · Landing Gear
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Not every gear is hydraulic. A pneumatic system works much like a hydraulic one, except that the return air is simply exhausted to atmosphere through the selector valve. Engine-driven air pumps charge a storage cylinder, and a pressure reducing valve feeds the selector. For extension the air passes through a second reducing valve, giving a lower pressure, for exactly the same reason that hydraulic systems use restrictors: to stop the gear slamming down. The rams themselves are damped by oil or grease in the hollow piston rod, forced past a fixed damper piston. Downlocks are over-centre drag struts, uplocks are spring rams released by air pressure, and the doors are moved by linkage. Light aircraft with no hydraulic system often use electric retraction: a reversible motor drives a screw jack and a torque tube, and rods and cables move the legs, with rubber cord helping the mains down. Limit switches stop and brake the motor when the gear is locked down and when it is fully up.
Part 6 · Safety and emergencies
Gear position indication You can often see the gear, but not whether it is locked : so microswitches on the locks drive lights Green = down and lockedRed = in transit, unlocked, or disagreeing with the leverNo lights = up and locked; bulbs duplicated against bulb failureSome light aircraft: one green all down, one amber all up; big jets add door indications and an ECAM/EICAS gear page A mechanical indicator confirms down and locked if the electrics fail
DOWN NOSE LEFT RIGHT down and locked
TRANSIT NOSE LEFT RIGHT unlocked / moving
UP NOSE LEFT RIGHT up and locked
Red also means the gear disagrees with the lever
Bulbs are duplicated; a press-to-test checks them
Some light aircraft: one green = all down, amber = all up
Back-up: mechanical indicator of down-and-locked
Chapter 5 · Landing Gear
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
From the flight deck you might be able to see a gear leg, but you can never be sure by looking that it is locked. So microswitches, or proximity sensors, on the uplocks and downlocks drive an indicator for each leg. The classic convention, which you must know cold, is this. Green means down and locked. Red means the gear is in transit, unlocked, or not where the lever says it should be. No lights at all means up and locked. During retraction you therefore see three greens go to three reds and then go out; on extension, reds then three greens. The bulbs are usually duplicated so a single failed bulb cannot give a false picture. Some light aircraft use a single green light for all gear down and a single amber light for all gear up. Large aircraft add door indications and a gear page on the electronic display. A mechanical indicator is often fitted too, so you can confirm down and locked with no electrical power.
Part 6 · Safety and emergencies
Lever lock, ground locks and the warning horn
DN
solenoid
Lever lock pin released only when the squat switch senses the strut extended (airborne) override for emergencies
REMOVE BEFORE FLIGHT
Ground locks pins with red flags stop the gear moving removed before flight, stowed on board, crew told
thrust lever near idle
gear NOT down and locked
HORN
Warning horn airspeed switch better than an isolation switch
Light aircraft also use a detented lever that must be pulled out before it will move, to prevent inadvertent selection.
Chapter 5 · Landing Gear
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three safety devices stop the most expensive mistakes. First, the gear selector lock. A spring-loaded plunger holds the lever in the down position, and a solenoid can withdraw it only when the squat switch, part of the air and ground logic, senses the strut extended after lift-off. With weight on the wheels the switch is open, so the lever cannot be raised. An override, such as a gated switch or a mechanical bypass, is provided for emergencies and maintenance. Second, ground locks: pins or sleeves with red flags that physically jam the gear. They are removed before flight, stowed on board, and the crew are told. Third, the warning horn, which sounds if any thrust lever is near idle, below about one third open, while the gear is not down and locked. An airspeed switch is better than an isolation switch, because an isolation switch can be used and then forgotten. The ground proximity warning system adds a too-low-gear warning.
Part 6 · Safety and emergencies
Emergency extension Modern airliners: usually free fall by gravity : uplocks released by a handle or switch, downlocks engage by springs Doors may stay open ; some have a frangible lower edge in case they touch the ground Others: an emergency pressure source : accumulator, hand pump , nitrogen or air bottle , electric pump Stored gas is used to extend the gear only, via shuttle valves that isolate the normal lines Selected by a separate handle or a gated position on the gear lever; confirm with the mechanical indicator
Free fall (gravity)
uplocks released by a handle (cable) or switch gravity + airflow lower it downlocks engage by springs doors may stay open
Stored energy + shuttle valve
N₂ bottle
or accumulator, hand pump, electric pump
emergency line
normal DOWN line (failed)
shuttle valve
gear jack
shuttle moves across, seals the normal line so gas cannot escape
Chapter 5 · Landing Gear
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
If the normal system fails, the gear must still come down and lock. On most modern airliners the emergency method is free fall. Pulling a handle, or operating a switch, releases the uplocks mechanically or electrically, and the gear falls under its own weight by gravity, with the airflow helping, until the downlocks engage under spring pressure. Watch the scene: because there is no power to move them again, the doors stay open. Large doors can then touch the runway on a firm landing, so some have a frangible lower edge. Other aircraft use an emergency pressure source instead: a hydraulic accumulator, a hand pump, an electric pump, or a bottle of compressed nitrogen or air. Stored gas is used only to extend the gear. It reaches the jacks through shuttle valves, which slide across to isolate the normal lines, and it is usually released by a separate handle or a gated emergency position on the gear lever. A mechanical indicator then confirms that the gear is locked down.
Part 6 · Safety and emergencies
Air/ground logic Many systems must know: on the ground or airborne? Sensed on the main gear oleos : compressed by weight on ground, extended by the weight of the wheels in flight Older: microswitches (squat or weight-on-wheels switches); newer: proximity sensors The signal drives relays that switch the affected circuits Usually duplicated on both main legs for redundancy Prevents gear retraction on the ground via the lever lock
Systems that use it
compressed = on the ground extended = in flight
sensor target
• gear lever lock (no retraction) • anti-skid touchdown protection • ground spoilers and thrust reversers • autobrake arming • pressurisation ground mode • take-off configuration warnings • stall warning, GPWS and other modes • duplicated on both main legs
Old: microswitches (squat switches) New: proximity sensors
Chapter 5 · Landing Gear
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
A surprising number of systems need to know one simple thing: is the aircraft on the ground or in the air? The answer comes from the main gear oleos. On the ground the weight of the aircraft compresses them; after lift-off the weight of the wheels and bogie extends them. Watch the strut extend as the aircraft lifts off, and then compress again at touchdown. Older aircraft sense this with microswitches, often called squat switches or weight on wheels switches. Newer aircraft use proximity sensors, which detect the position of a metal target by inductive or capacitive sensing, with no moving contacts to wear. Either way the signal goes to a relay, or a bank of relays, which switches the affected circuits. It is common to fit the sensors on both main legs for redundancy. The best-known user is the gear lever lock, which is how inadvertent retraction on the ground is prevented, but anti-skid, spoilers, reversers, pressurisation and many warnings use it too.
Part 6 · Safety and emergencies
Slush, and cycling the gear Slush (water, wet snow and ice) thrown into the gear on the take-off run can freeze at altitude Crews have then been unable to lower the gear at the destination If you must take off from slush: cycle the gear soon after take-off: UP, DOWN, UP The shocks of the cycle should shake the deposits off Observe the gear limiting speed (VLO /VLE ) while doing it
slush sprays into the gear and wheel wells
UP
DN
UP
cycle the gear: shocks shake the deposits free
cold at altitude: left in place, slush freezes and jams the gear
Chapter 5 · Landing Gear
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Runways covered in slush, a mixture of water, wet snow and ice, cause a special problem for the gear. During the take-off run the wheels throw slush all over the legs, the brakes and into the wheel wells. If the gear is then retracted and the aircraft climbs into freezing air, that slush can freeze solid in the gear bay, and on more than one occasion crews have been unable to lower the gear at their destination. The advice, if you really must take off from such a runway, is to cycle the gear soon after take-off: select it up, then down, then up again. The shocks of retracting and extending should be enough to break the deposits free before they freeze. Of course you must stay below the gear operating speed while you do it. Remember the answer: after a slush take-off, exercise the gear up and down, do not leave it hanging down or rush it straight up.
Summary
Landing gear: what to take into the exam Oleo strut Nitrogen carries the weight; oil through the orifice damps compression and extension. Static ≈ mid-stroke.
Layout and loads Mains just aft of CG carry ~90%. Loads: compression, rearward, side, forward (push-back), torsion.
Nose gear Centre before retraction (limited bay space ): cams or dashpot. Steering from the down line; bypass for towing.
Shimmy Rapid oscillation about the vertical axis at high ground speed; worn torque links ; cured by shimmy dampers .
Sequencing Sequence valves : doors open before gear moves. One-way restrictors slow extension .
Locks and lights Over-centre downlocks; spring-applied uplocks. Green locked down, red unlocked, none locked up.
Ground protection Squat switch lever lock (air/ground logic); ground locks removed and stowed on board .
Emergency Free fall (gravity) or stored nitrogen /accumulator via shuttle valves. Slush: cycle UP-DOWN-UP.
Chapter 5 · Landing Gear
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull the chapter together. In the oleo strut, nitrogen carries the weight and oil forced through the orifice damps both compression and extension, with the strut sitting about mid-stroke when static. The main gear sits just behind the centre of gravity and carries about ninety per cent of the weight, and the leg must survive compression, rearward, side, forward and torsional loads. The nose wheel must be centred before retraction because the bay is small, and it steers with pressure from the down line, with a bypass for towing. Shimmy is a rapid oscillation about the vertical axis at high ground speed, typically from worn torque links, cured by shimmy dampers. Sequence valves make the doors open before the gear moves, and one-way restrictors slow the extension. Downlocks are over centre and uplocks spring applied. The squat switch locks the lever on the ground, ground locks are stowed on board, and emergency extension is usually free fall, or stored nitrogen through shuttle valves.