Aircraft Systems · Chapter 11
Pneumatic Systems and Bleed Air Where an aircraft gets its working air: engine bleed from two compressor stages, the valves that tame it, heating for light aircraft, and the blowers and bleed supplies that feed a pressurised cabin.
COMPRESSOR STAGES LP stage HP stage to the manifold Packs Wing anti-ice Engine start Tank pressurisation Hot, high-volume, low-pressure air © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter eleven is about pneumatics: the hot, compressed air that a modern aircraft takes from its engines and uses for almost everything that is not done by hydraulics or electrics. It conditions and pressurises the cabin, keeps ice off the wings and engine intakes, starts the engines and pressurises the hydraulic tanks. We will follow the air from the compressor stages where it is tapped, through the valves that control its pressure and temperature, to the manifold and its users. Then we look at how unpressurised light aircraft heat their cabins, and at the blowers and bleed systems that supply the air for pressurised flight.
Roadmap
From the compressor to the cabin 1 · Users and sources What runs on air, and where the air comes from: engines, APU, ground cart, blowers.
2 · Engine bleed Two compressor taps, the HP shut-off valve, non-return valve, bleed valve and precooler.
3 · Protection Over pressure, overheat, isolation valves, gauges and warnings.
4 · Heating small aircraft Ram air, the exhaust heater muff, combustion heaters and carbon monoxide.
5 · Air for pressurised flight Cabin blowers, spill valves, mass flow, choke valve and duct relief.
6 · Bleed to the packs The pack valve, the hot charge air and what bleed costs the engine.
Exam focus Which stage is used when, what each valve does on failure, and why compressed air is hot.
Next lessons Lesson 12 cools the air (packs); lesson 13 uses it to pressurise the cabin.
Chapter 11 · Pneumatic Systems and Bleed Air
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the road map for this lesson. First we see what an aircraft uses compressed air for, and where that air comes from. Second, the engine bleed system itself: why air is tapped from two compressor stages, and the valves that switch between them, stop back-flow and regulate the pressure. Third, the protection: what happens on over pressure and overheat, and how isolation valves keep the two sides apart. Fourth, a detour to small unpressurised aircraft, which heat their cabins with ram air, an exhaust muff or a combustion heater, and the carbon monoxide danger that comes with them. Fifth, the supplies used for pressurised flight, including engine-driven cabin blowers with their spill valves. Finally, how bleed air is fed to the air-conditioning packs, and what it costs the engine. The next two lessons follow the air into the packs and the cabin.
Part 1 · Users
What the pneumatic system supplies Air conditioning and pressurisation (through the packs)Anti-icing of wing leading edges and engine intakesAir turbine motors : engine starting, hydraulic pumps, thrust reverser and flap or slat drivesPneumatic rams (e.g. thrust reverser) and cargo heating Pressurising the hydraulic reservoirs and the potable water tank Most users want high volume, low pressure air One air supply, many users Pneumatic manifold Air conditioning packs Pressurisation via the packs Wing and hot air Air turbine start, hyd pump, flaps Pneumatic rams e.g. thrust reverser Tank pressurisation hydraulic and water Cargo heating Engine compressor bleed air: main source APU ground and backup Ground air cart high-pressure connector Most users need large volumes of air at fairly low pressure
Chapter 11 · Pneumatic Systems and Bleed Air
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A pneumatic system is fitted to almost every modern transport aircraft, and its list of customers is long. The biggest users are air conditioning and pressurisation, which take their air through the packs. Hot air also keeps the wing leading edges and the engine intakes free of ice. Air turbine motors turn that air into shaft power: they start the engines, drive standby hydraulic pumps, and on some types drive thrust reversers or flaps and slats. Pneumatic rams can move things directly, such as a reverser, and the same air pressurises the hydraulic reservoirs and the drinking water tank, and heats the cargo holds. Notice what almost all of these users want: a large volume of air at a fairly low pressure, not the very high pressures of a hydraulic system. Some older turboprops did use high pressure air for gear and brakes, but that is now rare.
Part 1 · Sources
Where the air comes from Engine bleed : air tapped from the gas turbine compressor, the main sourceAPU bleed : for engine starting and air conditioning on the ground, and as a backupGround air cart : high-pressure air through a ground connectorEngine-driven blowers (cabin superchargers) on piston, turboprop and some jet typesOld high-pressure pneumatic systems for gear and brakes (e.g. F27) are now a minority Four ways to get the air engine bleed (main source) APU bleed (tail cone) ground cart HP connector Engine-driven blowers (cabin superchargers): piston and turboprop types, and jets with dirty compressor air Old high-pressure pneumatic gear and brakes (F27): now rare
Chapter 11 · Pneumatic Systems and Bleed Air
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where does all this air come from? Most of it is bled from the compressor of the gas turbine engines, so we call it bleed air. On the ground, with the engines stopped, the auxiliary power unit in the tail supplies bleed air to start the engines and to run the packs, and it can stand in for an engine bleed in flight on many types. A ground air cart can also be plugged into a high-pressure connector under the fuselage. Some aircraft, especially piston and turboprop types, and a few jets whose compressor air is considered too dirty, use engine-driven blowers, also called cabin superchargers, instead of bleed air. In the scene you can see the engines, the A P U in the tail cone, and bleed air flowing towards the packs in the belly.
Part 2 · Engine bleed
Why bleed air is tapped from two compressor stages 0 40 80 120 160 200 50 60 70 80 90 100 Engine speed N2 (% rpm) Tap pressure (psi gauge) HP valve OPEN LP air too weak HP valve CLOSED: all air from the LP stage pressure the system needs HP stage (e.g. 9th) LP stage (e.g. 5th) change-over ≈ 70 % Why two taps? Compressor delivery varies hugely from idle to full power. LP tap alone: too little at idle and descent. HP tap alone: far too hot and high at take-off power. Both, with an automatic change-over, keep the duct in a sensible pressure band. Curves illustrative; shape typical of a turbofan
Chapter 11 · Pneumatic Systems and Bleed Air
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the reason for the two bleed taps. The pressure available from any compressor stage rises steeply with engine speed, so between idle and full power the air available changes enormously. On the graph the orange curve is a low pressure stage, perhaps the fifth, and the red curve a high pressure stage, perhaps the ninth. The dashed blue line is the pressure the pneumatic system needs. At low engine speed, at idle on the ground or in a descent, the low pressure stage cannot reach that line, so a valve opens to take air from the high pressure stage. As the engine speeds up, the low pressure stage alone becomes enough, here at about seventy per cent, and the high pressure valve closes. So in all normal climb and cruise conditions the air comes from the low pressure stage, which is cooler and wastes less energy, while the high pressure tap is kept for low power.
Part 2 · Engine bleed
Inside the bleed system: valves along the duct Engine compressor: pressure and temperature rise stage by stage Non-return valve stops HP air entering the LP stage LP tap (e.g. 5th stage) HP shut-off valve open at low rpm, shut in cruise HP tap (e.g. 9th stage) Bleed valve (pressure-regulating, crew switch) Pre- cooler fan air overheat sensor to the manifold 44 DUCT psi Low rpm: HP valve open, HP air feeds the duct. Engine speeds up: LP air strong enough, HP valve closes, LP tap takes over.
Chapter 11 · Pneumatic Systems and Bleed Air
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the air through the bleed system. The engine compressor raises the pressure stage by stage. Air leaves the low pressure tap through a non-return valve, and from the high pressure tap through the high pressure shut-off valve. The two join, then pass the bleed valve, a pressure-regulating shut-off valve which the crew control with the bleed switch, and the precooler, where engine fan air takes away some of the heat. A duct gauge shows the pressure. At low power the high pressure valve is open and feeding the duct. Now watch it as the engine speeds up: the low pressure air becomes strong enough, the high pressure valve closes, and the flow switches entirely to the low pressure tap. The non-return valve has an important job while the high pressure valve is open: it stops high pressure air flowing backwards into the low pressure stage of the engine.
Part 2 · The HP shut-off valve
HP shut-off valve and non-return valve The HP valve is pressure sensitive and pneumatically operated Open when LP pressure is too low; closed once the LP stage is enough: in normal flight, air comes from the LP stage Opens slowly (engine start, packs on): no pressure surge Closes very quickly : keeps fumes and fire out of the cabin Non-return valves in the LP ducts stop HP air entering the LP stageHP shut-off valve behaviour Valve position OPEN SHUT opens slowly (start, packs on) snaps shut fast: fire, overpressure Slow opening: no pressure surge into the ducts or cabin Fast closing: keeps fumes and fire out of the cabin LP pressure low (idle, descent) HP valve opens LP pressure enough (climb, cruise) HP valve closes HP valve open NRV blocks back-flow to the LP stage
Chapter 11 · Pneumatic Systems and Bleed Air
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The high pressure shut-off valve deserves a closer look, because examiners like its behaviour. It is pressure sensitive and pneumatically operated: the low pressure duct pressure itself decides its position. When the low pressure air is too weak to maintain the required flow, the valve is open; as the engine speeds up, rising low pressure air closes it. So in all normal stages of flight the bleed air comes from the low pressure stage. The valve is designed to open relatively slowly, for example on engine start or when air conditioning is selected, so that there is no surge of pressure through the ducts. But it is designed to close very quickly, so that in an engine fire no fumes or flame can reach the cabin. And because the high pressure air would otherwise flow back into the engine through the low pressure port, non-return valves are fitted in the low pressure ducts.
Part 2 · Regulation
The bleed valve and the precooler The bleed air control valve is the separation point between engine and manifold Controlled electrically from the flight deck (BLEED switch); usually also regulates duct pressure The precooler is a heat exchanger cooled by engine fan air Typical airliner duct air: about 40 to 50 psi and roughly 200 °C (type-dependent) Duct pressure gauge , valve position indicators and overheat sensors are fitted Bleed valve and precooler Bleed valve regulates and shuts off BLEED switch Precooler engine fan air cools it fan air in dumped overboard overheat sensor from engine to manifold Typical airliner figures (vary by type): • Duct pressure regulated to about 40 to 50 psi • Precooler holds the duct air at roughly 200 °C
Chapter 11 · Pneumatic Systems and Bleed Air
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Downstream of the two taps sits the bleed air control valve. Think of it as the front door between the engine and the aircraft: it is the separation point between the engine and the pneumatic manifold, and it lets bleed air into the system only when the crew select the bleed switch on. On most jets it also regulates, holding the duct at a roughly constant pressure, typically somewhere around forty to fifty p s i, although the exact value depends on the type. Air straight from the compressor can be several hundred degrees, which would damage the ducts and the systems downstream, so on many engines it passes through a precooler, a heat exchanger cooled by air from the engine fan, which brings it down to roughly two hundred degrees. To let the crew monitor all this, the system has a duct pressure gauge, valve position indicators, and overheat sensors both inside and outside the ducts.
Part 3 · Protection
Over pressure and overheat protection Over pressure : usually a failed HP shut-off valve A pressure relief valve on the bleed duct vents the excess If it persists, a sensor vents the HP valve's opening pressure and forces it shut Overheat : a temperature switch downstream of the bleed valve closes the bleed valve Both give warning lights ; overheat drill: BLEED OFF , open the isolation valve Over pressure and overheat HP valve Relief valve Bleed valve temp switch OVER PRESSURE Usually a failed HP valve Relief valve vents the duct If it persists: a sensor vents the HP valve's opening pressure, forcing it shut Amber/red warning light OVERHEAT Temperature switch down- stream of the bleed valve Hot air: switch closes the bleed valve Warning light Drill: BLEED OFF, open the isolation valve
Chapter 11 · Pneumatic Systems and Bleed Air
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ducts must be protected from too much pressure and from too much heat. Over pressure is usually caused by a failure of the high pressure shut-off valve, which leaves the engine's hottest, highest pressure air connected to the duct. First line of defence is a pressure relief valve on the bleed air ducting, which vents the excess. If the over pressure persists, a sensor bleeds away the pressure that holds the high pressure valve open, so the valve is forced to close. Overheat is detected by an electrical temperature switch downstream of the bleed air control valve; when the air reaches a set temperature, it closes the bleed valve. Both conditions are shown to the pilots by warning lights. After an overheat, the drill is to select the bleed switch off and open the isolation valve, so that the other side of the system can supply the services that have just been lost.
Part 3 · Isolation
The manifold, isolation valves and the APU Each engine normally supplies its own side's users The sides are kept apart by isolation (crossbleed) valves , normally closed Opened to feed the other side if one engine's supply is lost The APU feeds the manifold for start and ground air conditioning Duct leaks are found by overheat detection loops along the ducts Two sides, kept apart ENG 1 ENG 2 APU isolation valve normally CLOSED isolation valve normally CLOSED Left pack + wing Right pack + wing psi gauge Open an isolation valve only to feed a side whose own source is lost
Chapter 11 · Pneumatic Systems and Bleed Air
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a multi-engined aircraft the bleed air from each engine is normally kept to its own side: the left engine feeds the left pack and the left wing, the right engine the right. The sides are joined by isolation valves, sometimes called crossbleed valves, which are normally closed. That way a leak or a fault on one side cannot drain the other. If one engine's supply is lost, for example after a bleed overheat, the isolation valve is opened so that the remaining engine can feed both sides, as the scene shows. The A P U usually connects to the middle of the manifold, so on the ground it can start either engine and run the packs. Because a burst duct would blow very hot air onto structure, wiring and fuel lines, overheat detection loops run along the ducts, and they warn the crew of a leak.
Part 3 · Other users
Air turbine motors and other pneumatic users Engine starting An air turbine starter on each engine spins the core; air from the APU, a ground cart or the other engine (crossbleed start).
Hydraulic power An air-driven hydraulic pump backs up an engine-driven pump on some types.
Flaps, slats and reversers Air motors or pneumatic rams drive some flap and slat systems and thrust reversers.
Tank pressurisation Regulated air pressurises the hydraulic reservoirs (no pump cavitation) and the potable water tank.
Anti-icing Hot air through piccolo tubes in the leading edges and nacelle lips (lesson 14).
Cargo heating Warm air keeps holds above freezing for animals and perishables.
Chapter 11 · Pneumatic Systems and Bleed Air
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Beyond the packs, bleed air does a lot of mechanical work. An air turbine starter on each engine uses air from the A P U, a ground cart or the other running engine to spin the engine up for start. Air-driven hydraulic pumps provide backup hydraulic power on some types. Air motors or pneumatic rams drive flaps and slats on some aircraft, and thrust reversers on others. Regulated air pressurises the hydraulic reservoirs, so that the pumps never cavitate, and the potable water tank, so water reaches the galleys and toilets. Hot air is the main way large jets anti-ice their wings and engine intakes, which you will meet in lesson fourteen. And warm air heats the cargo holds, so that animals and perishable freight survive the cold at altitude. All of these depend on the same manifold, which is why its protection matters so much.
Part 4 · Unpressurised aircraft
Ram air and the exhaust heater muff Unpressurised piston aircraft take ram air in through forward-facing intakes Some of it is heated in a heater muff (a close-fitting cowl round the exhaust) and mixed with cold air Warm air also feeds the windscreen demisters ; a fresh air blower helps on the ground Used air leaves through a vent under the fuselage Supply air must never be contaminated by exhaust gas : carbon monoxide Light aircraft: ram air and a heater muff ram air intake ram air scoop exhaust heater muff MIX heat / mixing valve cabin demist vent overboard fresh air blower (ground) Danger: a cracked exhaust inside the muff lets carbon monoxide into the cabin air. Heat OFF, fresh air ON, CO detector.
Chapter 11 · Pneumatic Systems and Bleed Air
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Small unpressurised piston aircraft do not need a pneumatic system at all; they simply use ram air. Forward-facing intakes, for example in the wing leading edge, scoop in outside air, which ventilates the cabin. To heat it, some of the ram air is ducted through a heater muff, a close-fitting cowl wrapped around the exhaust pipe, where it picks up heat from the hot pipe. The heated air is mixed with cold ram air in varying proportions to give a comfortable temperature, and some of it is sent to the windscreen to demist it. A small fresh-air blower may help on the ground, when there is no ram air. After use, the air leaves through a vent underneath. The great danger is contamination. If the exhaust pipe inside the muff cracks, carbon monoxide enters the cabin air, odourless and deadly. So the heat is turned off and fresh air selected at any suspicion, and a carbon monoxide detector is good practice.
Part 4 · Combustion heaters
The combustion heater Burns the aircraft's own fuel with air from a fan or blower Fuel through a solenoid valve , controlled by duct temperature sensors , manual override Ventilating air flows around the sealed chamber: no leak into the cabin air Required: automatic fuel shut-off on any malfunction Fire protection if the chamber fails, and overheat shut-off of the outlet airCombustion heater combustion chamber ventilating air in hot air to cabin fuel (solenoid valve) combustion air (fan) exhaust overboard (kept separate) Required safety devices • Automatic fuel shut-off on any malfunction • Fire protection if the chamber loses its integrity • Automatic shut-off if the outlet air gets too hot
Chapter 11 · Pneumatic Systems and Bleed Air
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
More capable light twins often use a combustion heater instead of a muff. It burns the aircraft's own fuel. A fan or blower supplies combustion air, and fuel arrives through a solenoid-operated valve, controlled by duct temperature sensors, with a manual override. Watch the chamber light up as it starts burning. The ventilating air for the cabin never enters the chamber: it flows around the outside of the sealed combustion chamber, inside an outer jacket, and picks up heat through the wall. The exhaust goes overboard separately. The design must make it impossible for leaks from inside the chamber to contaminate the cabin air, and the regulations demand safety devices: an automatic fuel shut-off in the event of any malfunction, adequate fire protection if the chamber loses its structural integrity, and an automatic shut-off if the outlet air temperature becomes too high.
Part 5 · Air for pressurised flight
Engine-driven cabin blowers Used where compressor bleed is not available or is too dirty Driven from the accessory gearbox , or turbo-compressors driven by bleed air Typical of piston and turboprop types, and some jets Types: centrifugal or positive displacement (Roots) Delivery depends on blower speed and air density Roots blower in section outside air in compressed, warmer air out Pockets of air are carried round the outside of the lobes, inlet to outlet
Chapter 11 · Pneumatic Systems and Bleed Air
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
When bleed air from a gas turbine compressor is not available, as on a piston engine, or is considered too contaminated, the cabin air comes from blowers, also called cabin superchargers. They are driven through the accessory gearbox, or by a turbo-compressor driven by bleed air. Blowers were essential for pressurised piston and turboprop aircraft and are still used on some jets. They come in two kinds: centrifugal, like a small jet compressor, and positive displacement, the Roots type with two lobed rotors, shown here. Outside air comes in, is squeezed and delivered through a non-return valve to the cabin supply. Notice the spill valve: at low altitude the blower moves far more air than the cabin needs, so the surplus is dumped overboard. As the aircraft climbs and the air thins, the spill valve closes progressively, so that the cabin still receives the same mass of air.
Part 5 · Mass flow
A blower moves more mass in dense air: the spill problem 0.0 0.5 1.0 1.5 2.0 0 5 10 15 20 25 30 Altitude (thousands of feet) Mass flow (× need) excess: spilled overboard blower delivery at fixed speed mass flow the cabin needs sized for 25000 ft Worked numbers (ISA) Density at 25000 ft: 0.45 of sea level Sea-level delivery: 2.23 × the need Spilled at sea level: 55 % of the output Cure: a spill valve wastes it; a variable-speed drive avoids the waste.
Chapter 11 · Pneumatic Systems and Bleed Air
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a blower need a spill valve at all? A blower at a fixed speed moves a fixed volume of air per revolution, so the mass it delivers is proportional to the air density. The cabin, on the other hand, needs a roughly constant mass flow at every height. So the blower has to be sized for the highest, thinnest air it will meet: here twenty five thousand feet, where the density is only about forty five per cent of sea level. Bring that same blower down to sea level and it delivers about two and a quarter times what the cabin needs. Over half of its output, the shaded area, must be dumped. A mass flow controller senses the flow and signals the spill valves to vent the excess to atmosphere, which protects the supply ducts from over pressure. That is wasteful, so where possible a variable-speed drive is used instead, slowing the blower down in dense air.
Part 5 · Blower system valves
Spill, non-return, relief and choke valves Mass flow controller + spill valve : dump surplus air; spill valve fully opens when the engine fire handle is pulledNon-return valve : keeps cabin pressure if the blower fails or spillsDuct relief valve : protects the supply duct from over pressureChoke valve : restricts the outlet to raise temperature and pressure when heat is neededHot and cold air mixed , automatic or manual Cabin blower installation gearbox drive Blower (Roots or centrifugal) outside air spill valve (overboard) NRV duct relief choke valve to the cold air unit and cabin Mass flow controller opens the spill valve to dump surplus air Spill valve fully opens when the engine fire handle is pulled Non-return valve holds cabin air if the blower stops or spills Duct relief valve protects the duct from over pressure Choke valve restricts flow to heat the air (more back pressure)
Chapter 11 · Pneumatic Systems and Bleed Air
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us name the valves in a blower installation and their jobs, because examiners ask about each. The mass flow controller watches the flow and opens the spill valve to dump surplus air overboard. The spill valve is also linked to the engine fire handle: pulling the handle opens it fully, so that no contaminated air from a burning engine is sent to the cabin. Downstream of the spill valve a non-return valve holds the cabin air in if the blower fails or the spill valve opens. A duct relief valve protects the supply duct against over pressure, because a burst duct could blow hot air onto fuel lines or wiring. Finally, the choke valve. By progressively closing it, the crew or the controller restricts the blower outlet, so the blower works harder against back pressure and the air leaves hotter and at a higher pressure. Opening it prevents excessive temperature and pressure. Hot and cold supplies are then mixed for comfort.
Part 5 · Physics
Why compressed air is hot Compressing air does work on it : its temperature rises Ideal rise: T2 = T1 × (pressure ratio)0.286 (absolute temperatures) Outside air at -44 °C , squeezed to cabin pressure at 30 000 ft, leaves at about +41 °C A take-off HP stage can deliver air at over 400 °C So any compressor (bleed or blower) supplies air that must be cooled : the packs Squeezing air heats it Cabin blower at 30 000 ft pressure ratio 2.5 -44 °C in +41 °C out Bleed from a pressure ratio 15 stage, sea level pressure ratio 15.0 +15 °C in +411 °C out -50 0 50 100 150 200 250 300 350 400 450 Temperature (°C). Compression efficiency 80 to 85 % assumed
Chapter 11 · Pneumatic Systems and Bleed Air
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a piece of physics that explains the whole of the next lesson. When you compress air you do work on it, and that work appears as heat, so the air gets hotter. For an ideal compressor the absolute temperature rises with the pressure ratio raised to the power nought point two eight six; real compressors, being less than perfect, heat it a little more. Take outside air at thirty thousand feet, at about minus forty four degrees, and squeeze it up to a typical cabin pressure: the ratio is about two and a half, and it comes out at roughly plus forty. Air from a high pressure engine stage at take-off can be well over three hundred degrees. So whether the air comes from a blower or from the engine, it arrives far too hot for people. That is why every pressurised aircraft has air-conditioning packs, and also why a failed oil seal in a compressor matters: oil fumes would be carried straight into the cabin air.
Part 6 · Bleed to the packs
Engine bleed air systems and the pack valve The most widely used supply for air conditioning on modern aircraft A branch off the bleed duct feeds each pack through a pack (flow control) valve The pack valve controls bleed air into the pack : on/off and the mass flow Bleed air is always hotter than the cabin needs, so the pack cools it Pack valves close automatically for some faults, e.g. pack overheat or engine fire From the duct to the pack pneumatic manifold (≈ 40 to 50 psi, ≈ 200 °C) Pack (flow control) valve shuts off and meters bleed air INTO the pack PACK cooling machine cool air to the mixer wing anti-ice other users The pack valve is the one valve that decides how much bleed air enters the pack
Chapter 11 · Pneumatic Systems and Bleed Air
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
On jet transports the engine bleed air system is by far the most common supply for air conditioning. Hot pressurised air from the low or high pressure stage reaches the bleed duct, and a branch off the duct feeds each air-conditioning pack. Each pack has its own pack valve, also called the flow control valve, which controls the bleed air going into the pack: it shuts it off completely when the pack is selected off, and when it is on it meters a steady mass flow. On many types this valve is the mass flow controller, or works with one. The packs sit low in the belly fairing, under the wing box, as the scene shows. Because bleed air is always far hotter than the cabin needs, the pack cools it before it is sent up to the cabin. The pack valve also closes automatically for some faults, such as a pack overheat, or when an engine fire handle is pulled.
Part 6 · The price
What bleed air costs Air compressed by the engine and then used elsewhere means more fuel Bleed reduces thrust for a given N1 and raises EGT A failed compressor oil seal can contaminate the bleed air with oil fumes Ducts at around 200 °C need overheat and leak detection Hence packs-off take-offs on some types, and the APU supplying the packs on the ground Bleed air is not free Fuel every pound of air compressed and then thrown away cost fuel Thrust and EGT less thrust for the same N1; higher exhaust temperature Contamination oil seal leaks put oil fumes or smoke into the bleed air Heat ducts at 200 °C plus need overheat and leak detection along their length So packs may be selected OFF for some take-offs, and the APU feeds them on the ground
Chapter 11 · Pneumatic Systems and Bleed Air
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bleed air is convenient, but it is not free. Every kilogram of air that the engine compresses and then hands to the pneumatic system is air that does not produce thrust, so bleed increases fuel consumption, reduces the thrust available for a given fan speed, and raises the exhaust gas temperature. For take-off performance, some operators therefore select the packs off, or supply them from the A P U, for the take-off run. Because the air comes straight from the engine compressor, a failure of a compressor oil seal can contaminate the bleed air with oil fumes or even smoke, which is why fume events are taken seriously. And the ducts carry air at around two hundred degrees, so they need the overheat and leak detection we met earlier. Some newer airliners avoid bleed altogether by using electrically driven cabin compressors, but the exam focuses on bleed air systems.
Comparison
Ways of supplying cabin air Supply Where the air comes from Strengths Weak points Ram air Forward intakes, light aircraft Simple, no power needed Unpressurised; heating needs muff or heater Engine bleed LP / HP compressor stages Light, simple, plenty of air Hot, costs fuel and thrust, oil contamination risk Cabin blower Gearbox-driven Roots or centrifugal blower Clean air; works with piston engines Heavy; needs spill valve and mass flow control Turbo-compressor Compressor driven by a bleed-air turbine Clean outside air with bleed power More parts APU / ground cart APU compressor or ground connector Engines can be off Ground or backup use only
Whatever the source, compression heats the air: it always goes to a cooling pack before the cabin.
Chapter 11 · Pneumatic Systems and Bleed Air
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us compare the ways of supplying cabin air. Ram air is the simplest of all: forward-facing intakes on a light aircraft, no power needed, but no pressurisation, and heating needs a muff or combustion heater. Engine bleed is light, simple and gives plenty of air, but it is hot, it costs fuel and thrust, and an oil seal failure can contaminate it. A cabin blower driven from the gearbox gives clean air and works with piston engines, but it is heavy and needs a spill valve and mass flow control. A turbo-compressor uses bleed air only as a power source, driving a compressor that takes in clean outside air. And the A P U or a ground cart supply the system when the engines are off. Whatever the source, remember the physics from earlier: compression heats air, so the supply always goes to a cooling pack before it reaches the cabin.
Summary
Pneumatics: the essentials Users and sources Packs, pressurisation, anti-ice, air turbine motors, rams, tank pressurisation, cargo heat. Air from engine bleed, APU, ground cart or blowers: high volume, low pressure.
Two taps LP stage in normal flight; HP valve opens at low rpm, closes as LP pressure rises. Opens slowly, shuts fast. NRVs stop HP air entering the LP stage.
Bleed valve and protection Bleed valve: engine/manifold separation point, crew switch. Over pressure: relief valve, then HP valve forced shut. Overheat: temp switch shuts the bleed valve; BLEED OFF, open isolation.
Isolation Each engine feeds its own side; isolation valves normally closed, opened to feed a side that has lost its source.
Light aircraft Ram air, heater muff (CO danger from cracked exhausts), combustion heater with auto fuel shut-off, fire protection and overheat shut-off.
Blowers and packs Blower delivery follows density: spill valve and mass flow controller; NRV, duct relief, choke valve. Pack valve meters bleed into the pack; compressed air is hot.
Chapter 11 · Pneumatic Systems and Bleed Air
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull the lesson together. The pneumatic system supplies the packs, pressurisation, anti-icing, air turbine motors, rams, tank pressurisation and cargo heat, using high-volume, low-pressure air from engine bleed, the A P U, a ground cart or blowers. Bleed is taken from two stages: the low pressure stage in normal flight, with the high pressure valve opening at low engine speed, opening slowly and shutting fast, and non-return valves protecting the low pressure stage. The bleed valve separates engine and manifold and is worked by a crew switch. Over pressure is met by a relief valve and then by forcing the high pressure valve shut; overheat closes the bleed valve, after which the crew open the isolation valve. Light aircraft use ram air, heater muffs and combustion heaters, with carbon monoxide the great danger. Blowers need spill valves because their delivery follows density. And the pack valve meters the hot bleed air into the pack.