Aircraft Systems · Chapter 10
Powered Flying Controls and Fly-by-wire How hydraulic power moves the surfaces of large aircraft, how artificial feel is made, and how fly-by-wire computers and redundancy keep control safe.
SIDESTICK · COMPUTERS · JACKS
power moves the surface; feel and logic are made for the pilot
ELAC
SEC
FAC
servo jack
sidestick
flight control computers
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to powered flying controls and fly-by-wire. On a large, fast aircraft the air loads on the control surfaces are far too high for human muscles, so hydraulic power does the work. In this lesson you will see how a powered flying control unit follows the pilot's input exactly, why its irreversibility means feel must be made artificially, and how spring boxes, Q pots and feel computers do it. Then we move to fly-by-wire, where electrical signals and computers replace cables, and finish with the redundancy that makes all of this safe.
Roadmap
Muscle, power and computers 1 · Why power Control force limits. Power-assisted versus fully powered.
2 · The PFCU Actuator, servo valve, follow-up, hydraulic lock, duplication and bypass.
3 · Artificial feel Spring box, Q pot, hydraulic Q feel, feel computer and feel trim.
4 · Fly-by-wire Signal path, A320 architecture, computers and redundancy.
Chapter 10 · Powered Flying Controls and Fly-by-wire
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First, why large aircraft need powered controls at all, the limits on the force a pilot may be asked to apply, and the difference between power-assisted and fully powered systems. Second, the powered flying control unit itself: the actuator, the servo valve, the follow-up that makes the surface move exactly as far as the pilot asks, the hydraulic lock that holds it there, and the duplication and bypass that keep it safe when a hydraulic system fails. Third, artificial feel: the spring box, the Q pot, the hydraulic Q feel unit and the feel computer with feel trim. Finally fly-by-wire: the signal path from stick to surface, the architecture of the A320 with its three kinds of computer, and the redundancy that makes it all trustworthy.
Part 1 · Why power
Air loads beyond human strength Large surfaces and high speeds give very large hinge moments Certification sets maximum pilot forces (large aeroplanes, CS / JAR 25.143) Hinge moments grow with q = ½ρV² : four times as large at double the IAS Help comes from hydraulic (most common) or electric power Degree of help: power-assisted or fully powered
Maximum pilot forces (large aeroplanes)
Pitch
Roll
Yaw
Short, one hand
50 lbf
25 lbf
—
Short, two hands
75 lbf
50 lbf
—
Short, rudder
—
—
150 lbf
Prolonged
10 lbf
5 lbf
20 lbf
Dynamic pressure q = ½ρV² (kPa)
0
50
100
150
200
250
300
0
5
10
15
IAS (kt)
3.6 kPa
14.6 kPa
Chapter 10 · Powered Flying Controls and Fly-by-wire
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
On modern large aircraft the control surfaces are big, and they are moved at high speed, so the air loads on them are enormous. The certification rules for large aeroplanes set the maximum force a pilot may be asked to apply. As a guide, for a short period you may be asked for about fifty pounds force in pitch with one hand or seventy five with two, twenty five or fifty in roll, and up to one hundred and fifty on the rudder pedals, while prolonged forces must be far lower, around ten, five and twenty. The loads themselves grow with the dynamic pressure, half rho V squared, which as the graph shows is about three point six kilopascals at one hundred and fifty knots but over fourteen at three hundred. To keep within the limits, hydraulic power, or occasionally electric power, is used. Depending on how much help is given, the system is power-assisted or fully powered.
Part 1 · Why power
Power-assisted or fully powered Power-assisted : the pilot supplies a proportion of the force; the jack the restAssisted controls keep natural feel and are reversible if loads are large enough Fully powered : the jack supplies all the forceFully powered controls are irreversible and need artificial feel Fully powered systems need duplication against failure
Power-assisted: the pilot shares the load
pilot 25 %
hydraulic jack 75 %
Some of the air load is felt: natural feel, reversible
(if surface loads are large enough). No feel unit needed.
Hydraulic failure: still controllable, but heavy.
Fully powered: the jack takes it all
hydraulic jack 100 %
No air load reaches the pilot: irreversible.
Needs artificial feel, and duplication of power
units and hydraulic systems for safety.
Example split shown for power assistance is illustrative.
Chapter 10 · Powered Flying Controls and Fly-by-wire
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two degrees of help. In a power-assisted system the pilot still provides a proportion of the force needed, and a hydraulic jack provides the rest. Because part of the air load still comes back to the pilot, the controls keep their natural feel, and if the surface loads are large enough they are reversible. No artificial feel unit is required, and if the hydraulics fail the aircraft can still be flown manually, although heavily. In a fully powered system the jack provides all of the force. No air load reaches the cockpit, so the system is irreversible and has no natural feel; feel must be created artificially, in proportion to speed and to the deflection. And because the pilot could not move the surfaces at all without power, the units and the hydraulic systems feeding them must be duplicated. Remember the pairing for the exam: assisted, reversible, natural feel; fully powered, irreversible, artificial feel.
Part 2 · The PFCU
The parts of a powered control system
Control column
pilot input
Servo (control) valve
meters fluid
Actuator
piston fixed, body moves
Surface
Artificial feel unit
in parallel with column
follow-up: the moving body re-centres the valve
pressure in, return out:
hydraulic power does the work
Hydraulic actuator The jack that moves the surface, often with the piston fixed and the body moving .
Servo (control) valve A spool valve worked by the pilot's linkage that meters fluid to the actuator.
Follow-up Feedback that closes the valve when the surface has moved as far as selected .
Artificial feel Gives a force proportional to air speed and deflection .
Chapter 10 · Powered Flying Controls and Fly-by-wire
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
A simple power operated control system has three essential components: a hydraulic actuator, a servo or control valve, and an artificial feel unit. On top of these it must have some form of follow-up, also called feedback. The follow-up ensures that the surface moves by an amount proportional to the pilot's selection and then stops, rather than running on to full deflection. And the feel must be proportional to the air loads the surface would have, which means to speed and to deflection. In many powered flying control units, or P F C Us, the piston is fixed to the aircraft structure and the cylinder body moves, carrying the surface linkage with it. The control valve is mounted on the moving body, which is what gives the follow-up, as we will see on the next slides.
Part 2 · The PFCU
How a PFCU moves the surface Column back: the linkage moves the control valve spool One actuator port opens to pressure , the other to return With the piston fixed, the body moves and drives the elevator The moving body re-covers the ports : the follow-up Fluid is trapped: a hydraulic lock holds the surface
Column pulled: valve opens, body moves
input from the column
to elevator
piston fixed
to structure
Pressure (red) to the left chamber, return (blue)
from the right: the body moves left, raising the
elevator. As it moves it carries the valve sleeve with it
until the ports close: follow-up, then hydraulic lock.
Chapter 10 · Powered Flying Controls and Fly-by-wire
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how a fully powered flying control unit works. When the control column is pulled back, the linkage moves the spool of the control valve. Watch the scene. One port of the actuator is opened to hydraulic pressure and the other is opened to return. In the unit in the diagram the piston is fixed to the aircraft structure, so the pressure moves the actuator body instead, and the body drives the elevator up. Now the clever part. The valve housing is carried on the moving body, so as the body moves it gradually re-covers the ports. When the body has moved as far as the pilot's input, the ports are covered again, the supply is cut off and the return is blocked. That is the follow-up. The fluid trapped on both sides of the piston forms a hydraulic lock, so the surface stays exactly where it was put. The surface movement is therefore proportional to the selection.
Part 2 · The PFCU
Follow-up in three steps
1 · Neutral
input from the column to elevator piston fixed to structure
ports covered, fluid locked
2 · Input
input from the column to elevator piston fixed to structure
spool moved: pressure in, body starts to move
3 · Follow-up
input from the column to elevator piston fixed to structure
body has caught up: ports covered again
Surface movement is proportional to the input. Air loads on the surface cannot move the column: the unit is irreversible .
Chapter 10 · Powered Flying Controls and Fly-by-wire
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us slow the follow-up down. In step one, everything is in neutral: the spool covers both ports, fluid is locked on both sides of the piston, and the surface is held. In step two the pilot moves the input, the spool is displaced, and pressure flows into one chamber while the other is opened to return. The body starts to move. In step three the body has moved by exactly the amount of the input, carrying the valve housing with it, so the ports are covered again and the fluid is locked once more. If the pilot moves the column a little, the surface moves a little; if he moves it a lot, the surface moves a lot. Now think about a gust pushing on the surface. It cannot move the column, because the locked fluid holds the body, and the column only connects to the spool. That is why a fully powered unit is irreversible.
Part 2 · Safety
Duplicated units and the bypass Powered controls need duplication against system failure Two or more PFCUs per surface, in parallel or in series (tandem) Each unit fed by a separate hydraulic system If one system fails, its pressure drop lets a spring-loaded piston open a bypass No hydraulic lock: the dead unit follows the working one
Two PFCUs on one surface, two hydraulic systems
PFCU · System A
System A
PFCU · System B
System B
common
output
If system A fails:
bypass open
pressure drop: a spring-
loaded piston opens a bypass
between the two chambers
So the dead unit cannot form a hydraulic lock:
it is simply dragged along by the working unit.
Units may be in parallel (shown) or in series (tandem).
Chapter 10 · Powered Flying Controls and Fly-by-wire
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because a fully powered surface cannot be moved by the pilot, some form of duplication is essential. Each surface is driven by two or more powered units, arranged either in parallel, side by side on the same surface, or in series, in a tandem unit with two pistons in line. Each unit is supplied by a separate hydraulic system. But think about what happens when one system fails. Its unit is still full of fluid, and a unit with locked fluid would hold the surface against the working unit. To prevent that, each unit has a bypass. When its pressure drops, either through failure or because the pilot has taken that system off line, a spring-loaded piston opens a bypass channel between the two sides of the actuator. With no hydraulic lock, the dead unit is simply dragged along by the working one, which keeps full control of the surface.
Part 2 · Safety
When the power goes Power-assisted : revert to manual, heavy but controllableManual reversion on some fully powered types: tabs fly the surfaceOtherwise: several independent hydraulic systems, plus RAT and PTU Fly-by-wire: a mechanical back-up for a limited time Total loss of control power must be extremely improbable
If all hydraulic power were lost
Power-assisted
reverts to manual: heavier, but natural
Fully powered + manual reversion
controls disconnected from the jacks; tabs fly the surface
Fully powered, no reversion
must never lose all power: 3 or 4 systems, RAT, PTU
Fly-by-wire
mechanical back-up (e.g. rudder, stabiliser trim) for a short period
Manual reversion via servo tabs is possible on some types.
Chapter 10 · Powered Flying Controls and Fly-by-wire
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
What if hydraulic power is lost completely? With power-assisted controls, the pilot simply flies manually, with much heavier forces, because the mechanical connection to the surface is still there. Some fully powered aircraft have manual reversion: the controls can be disconnected from the jacks, and servo tabs then fly the surfaces, so the aircraft remains controllable, though with reduced authority. Most modern aircraft do not rely on reversion. Instead they have three or four independent hydraulic systems, with a ram air turbine and power transfer units to keep at least one alive. Fly-by-wire aircraft keep a limited mechanical back-up. On the A320, for example, the rudder pedals and the stabiliser trim wheel are mechanically connected, so the aircraft can be flown for a short time if every flight control computer is lost. The design aim is that total loss of control is extremely improbable.
Part 3 · Artificial feel
Why artificial feel, and what it must do Without feel the pilot has no idea how much he is moving the surface Danger of over-controlling and overstressing the aircraft Feel must grow with deflection and with airspeed Simple spring box up to a hydraulic Q feel system Fully powered (irreversible) needs it; power-assisted (reversible) does not
Artificial feel: force grows with deflection and speed
0
5
10
15
0
10
20
30
40
elevator deflection (°)
column force (lbf)
150 kt
250 kt
300 kt
30 lbf
Spring part: proportional to deflection (all speeds).
Q part: proportional to dynamic pressure × deflection.
(illustrative values)
Chapter 10 · Powered Flying Controls and Fly-by-wire
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
With hydraulic pressure moving the surfaces, the pilot has lost all control feel. He would have no idea how far he was deflecting the surface or how hard he was loading the aircraft, and he could easily over-control it, or at high speed overstress the structure. So artificial feel units are fitted. They must give a column force proportional to the amount of control movement, and also proportional to the speed of the aircraft, just as a manual control would. The graph shows illustrative figures. At one hundred and fifty knots the force rises gently with deflection; at three hundred knots the same ten degrees of elevator needs about thirty pounds force. Feel units range from a simple spring box to a Q pot system using pitot and static pressure. Remember: a fully powered, irreversible system requires artificial feel; a power-assisted, reversible one does not.
Part 3 · Artificial feel
The spring feel unit A plunger from the column sits between two springs Column either way compresses one spring Force ∝ deflection , and it re-centres the column But the force is the same at every speed Adequate at low speed; at high speed more resistance is needed
Simple spring feel unit
from the control column
fixed
Column either way compresses one spring
and the springs re-centre it
Good enough at low speed, but its force does
not change with speed: at high speed it would
let the pilot overstress the aircraft.
Hence Q feel: force proportional to ½ρV².
Chapter 10 · Powered Flying Controls and Fly-by-wire
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The simplest artificial feel unit is a spring box. A plunger, connected to the control column, sits between two springs inside a box fixed to the structure. Watch the scene. Moving the column one way compresses one spring, and moving it the other way compresses the other spring, so the column force increases with deflection, and the springs always try to return the column to neutral. That gives a sense of how far the control has been moved. The weakness is that a spring knows nothing about airspeed: the force for a given deflection is the same at eighty knots as at three hundred. Spring feel may be adequate at low speeds, but at high speeds much greater resistance to control movement is needed, otherwise a light, easy control could let the pilot overstress the aircraft. That is the job of Q feel.
Part 3 · Artificial feel
The Q pot A piston in a pot, connected so that any column movement pulls it forward Pitot pressure on the front, static on the backNet force ∝ pitot − static = ½ρV², the dynamic pressure q So feel grows with speed squared A pot big enough to feel would be huge : real units add hydraulics
Simple Q pot
to column
pitot (P + q)
static (P)
net push = q × area
Pitot − static = ½ρV² (dynamic pressure)
Worked example: piston area 20 cm²
150 kt: q = 3647 Pa, force = 7.3 N
300 kt: q = 14589 Pa, force = 29.2 N
Far too small to feel: real units use the Q pressure
to work a hydraulic valve that powers a feel piston.
Chapter 10 · Powered Flying Controls and Fly-by-wire
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
To make the feel grow with speed, we use dynamic pressure, called Q. A simple Q pot contains a piston connected through a double linkage to the column, so that whichever way the column moves, the piston is pulled forward against pitot pressure, which is fed to the front of the pot. The back of the pot is open to static pressure. Pitot pressure is static plus dynamic pressure, so the difference across the piston is just the dynamic pressure, half rho V squared, and the resisting force is proportional to it. Now the worked example. With a piston of twenty square centimetres, at one hundred and fifty knots the dynamic pressure is about three thousand six hundred pascals, giving only about seven newtons. At three hundred knots it is about twenty nine newtons. Far too small to be useful, so a real Q pot would have to be enormous. Instead the Q pressure is used to control hydraulic pressure.
Part 3 · Artificial feel
The hydraulic Q feel unit Pitot above a diaphragm, static below itThe diaphragm positions a spool valve : faster, more pressure to the feel piston The feel piston resists the column: force grows with speed and with deflection The return port is never fully closed , avoiding a hydraulic lock The feel unit is connected in parallel with the pilot's column
Hydraulic Q feel unit
pitot
static
diaphragm
spool valve
P
R
column
feel piston
Faster: more pitot pressure, diaphragm pushes the spool,
more pressure on the feel piston, more column force.
Big deflection has the same stiffening effect.
The return port is never fully closed (no hydraulic lock).
The feel unit is connected in parallel with the column.
Chapter 10 · Powered Flying Controls and Fly-by-wire
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The practical answer is a hydraulic Q feel unit. Pitot pressure is fed to the upper chamber of a small Q pot, above a diaphragm, and static pressure below it. The faster the aircraft flies, the harder the diaphragm is pushed down. The diaphragm moves a spool valve, opening the pressure port further and partly closing the return port, so hydraulic pressure builds up in front of the feel piston, which the column has to push against. Some fluid also passes through a narrow channel under the spool to damp its movement. So the faster you fly, the greater the pressure and the heavier the controls. A large control movement has a similar effect to high speed. Note two details. The return port is never fully closed, because that would create a hydraulic lock. And the feel unit is connected in parallel with the pilot's control column, not in series with the surface.
Part 3 · Artificial feel
The feel computer and feel trim Combines spring feel (low speed) and hydraulic feel (high speed) A double cam on the quadrant always pushes the column towards neutral Feel computer: airspeed diaphragm and stabiliser position cam set a metering valve Moving the column forces the feel piston; a relief valve bleeds to return Feel trim : trimming the stabiliser resets the feel datum: hands-off
Feel computer with stabiliser input and feel trim
Airspeed
pitot − static diaphragm
Stabiliser position
cam and bellows
Metering valve
meters hydraulic pressure
Feel actuator
on the elevator quadrant
Double cam on the quadrant: the feel springs and
the hydraulic piston always push the column to neutral.
Pilot moves the column: he compresses the spring and
forces the feel piston in; a relief valve bleeds to return.
Feel trim
Trimming the stabiliser also moves the bellows and so
resets the feel datum: the stick force is cancelled and
the elevator returns to neutral: hands-off flight.
Chapter 10 · Powered Flying Controls and Fly-by-wire
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
A complete artificial feel system for the elevator combines both kinds of feel. Springs give feel at low speed, and hydraulic feel takes over at higher speeds. A double cam on the aft elevator quadrant shows how the system always tries to put the column back to neutral: to move the column, the pilot must compress the spring and force the hydraulic feel piston back. The hydraulic pressure is set by a feel computer. Pitot and static pressures act on an airspeed diaphragm, which loads a metering valve, and a second input comes from the stabiliser position through a cam and bellows. The metering valve keeps modulating to hold the right pressure, bleeding the excess to return. Feel trim follows naturally: when the pilot trims the stabiliser to cancel a stick force, the bellows let the metering valve relax, the feel datum moves, the stick force disappears and the elevator returns to neutral, so the aircraft flies hands off.
Part 4 · Fly-by-wire
What fly-by-wire means A powered control system with electrical inputs to the servo valves, not mechanical Pilot input via sidestick or a conventional column and pedals Transducers turn movement into electrical signalsSignals are amplified and processed by computers , which command the actuators Surfaces are still moved hydraulically
Fly-by-wire: the signal path
Sidestick or column
pilot input
Transducers
movement to electrical signal
Flight control computers
amplify, process, apply laws
Servo valve
solenoid / torque motor
Hydraulic actuator
moves the surface
position
feedback
Electrical signalling replaces the cables and rods.
Chapter 10 · Powered Flying Controls and Fly-by-wire
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fly-by-wire is a powered flying control system in which the inputs to the servo valves are electrical rather than mechanical. The pilot uses either a sidestick, as on Airbus aircraft, or a conventional column, together with rudder pedals. Transducers convert the pilot's movement into an electrical signal, which is amplified and processed by computers. The processed command then drives a solenoid or torque motor operated servo valve on each hydraulic actuator, and the actuator reports its position back to the computers. Watch the scene: the pilot pushes the sidestick left, and the computers command the left ailerons and spoilers together, rolling the aircraft. Because the computers stand between the pilot and the surfaces, they can do more than relay the input: they can shape the response, damp unwanted motion, and protect the aircraft from leaving its flight envelope. Cables and rods are replaced by wires, saving weight and maintenance.
Part 4 · Fly-by-wire
A320 flight control architecture Axis or function Surfaces Control Pitch Elevators Electrical Pitch trim Trimmable horizontal stabiliser Electrical (normal and alternate); mechanical manual trim wheel Roll Ailerons and spoilers Electrical Yaw Rudder Mechanical , with electrical yaw damping, turn coordination and trimHigh lift Slats and flaps Electrical Speed brakes Spoilers Electrical
All surfaces are hydraulically actuated. Flight deck: two sidesticks, conventional pedals, pedestal controls and indicators.
Chapter 10 · Powered Flying Controls and Fly-by-wire
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 is the classic example. Every surface is moved hydraulically, but the way each is controlled differs. The elevators are controlled electrically. The trimmable horizontal stabiliser is controlled electrically in normal and alternate operation, with a mechanical back-up through the manual trim wheel. In roll, both the ailerons and the spoilers are controlled electrically. The rudder is the exception: it is controlled mechanically from the pedals, with electrical inputs for yaw damping, turn coordination and rudder trim. Slats and flaps, and the speed brakes, are electrical. On the flight deck there are two sidesticks, conventional rudder pedals, and controls and indicators on the pedestal. Notice the pattern: the two mechanical links, the rudder and the stabiliser trim wheel, are exactly the back-up that lets the aircraft be flown for a short time if all the computers are lost.
Part 4 · Fly-by-wire
Three kinds of computer
ELAC 1
ELAC 2
SEC 1
SEC 2
SEC 3
FAC 1
FAC 2
Ailerons
Elevators + stabiliser
Spoilers
Rudder (electrical part)
ELAC × 2 Elevator Aileron Computer . Controls the ailerons , elevators and stabiliser .
SEC × 3 Spoilers Elevator Computer . Controls the spoilers , and gives standby elevator and stabiliser control.
FAC × 2 Flight Augmentation Computer . Electrical rudder control: yaw damper, turn coordination, trim, travel limit.
Chapter 10 · Powered Flying Controls and Fly-by-wire
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The A320 uses three types of flight control computer, seven in all. There are two ELACs, elevator aileron computers, which control the ailerons, the elevators and the stabiliser. There are three SECs, spoilers elevator computers, which control the spoilers, the upper wing surfaces, and provide standby control of the elevators and the stabiliser if the ELACs are lost. And there are two FACs, flight augmentation computers, which provide the electrical rudder functions: yaw damping, turn coordination, rudder trim and the rudder travel limit. Notice the overlap. Pitch can be controlled by either ELAC or by the SECs, and roll by the ELACs through the ailerons or by the SECs through the spoilers. So the loss of one computer, or even of a whole type of computer, still leaves control in every axis. That overlap is part of the redundancy we look at next.
Part 4 · Fly-by-wire
Redundancy Surfaces split into sections, each with its own actuators Actuators fed by different hydraulic systems Several computers of dissimilar design A mechanical back-up for the most basic control Aim: no single failure loses control of an axis
Each surface split and fed by more than one system
spoilers 1 to 5 (from root)
aileron: G + B
left elevator: B + G
right elevator: Y + B
rudder: G, B and Y
stabiliser motors: G + Y
Green
Blue
Yellow
Computers: 2 ELAC + 3 SEC + 2 FAC, of two different
designs (dissimilar hardware and software), so one
design fault cannot take out every computer.
No single failure of a hydraulic system, actuator
or computer should cost control of any axis.
A320 example; colours are system names, not pressures.
Chapter 10 · Powered Flying Controls and Fly-by-wire
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Safeguards against losing control after a hydraulic or electrical failure must be built into every modern transport aircraft, and the usual method is redundancy. The control surfaces are split into two or three sections, each powered by separate actuators connected to different hydraulic systems. Look at the A320 example. The five spoilers on each wing are shared between the green, yellow and blue systems; each aileron and each elevator has two actuators on two different systems; the rudder has three, one on each system; and the stabiliser has two motors. The computers are redundant too: seven of them, of two different designs, with different hardware and software, so that a single design error cannot affect them all. The result is that no single failure of a hydraulic system, an actuator or a computer should cost control of any axis. Remember that green, blue and yellow here are system names, not pressures.
Part 4 · Fly-by-wire
Control laws and envelope protection Law When What the pilot gets Normal law All normal Stick commands a load factor (pitch) and roll rate ; full envelope protection Protections (normal law) Always active Load factor about +2.5 / −1 g clean; pitch attitude +30° / −15° ; bank 67° ; high angle of attack; high speed Alternate law After some multiple failures Most protections lost or reduced ; aircraft still computer-controlled Direct law Further failures Stick deflection gives surface deflection directly, no protections; manual trim Mechanical back-up All computers lost Rudder pedals and stabiliser trim wheel only, for a limited time
A320 family values; other fly-by-wire types differ in detail.
Chapter 10 · Powered Flying Controls and Fly-by-wire
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because computers stand between the pilot and the surfaces, fly-by-wire aircraft fly according to control laws. On the A320 family, normal law is used when everything is working. The sidestick then commands a load factor in pitch and a rate of roll, rather than a surface angle, and the aircraft is protected from leaving its envelope. In the clean configuration the load factor is limited to about plus two point five and minus one g, pitch attitude to about thirty degrees nose up and fifteen nose down, bank to sixty seven degrees, and there are protections against a high angle of attack and against overspeed. After certain multiple failures the system degrades to alternate law, in which most of these protections are lost or reduced, and after further failures to direct law, where stick deflection gives surface deflection directly, with no protections and manual trimming. If every computer is lost, the mechanical back-up remains: the rudder pedals and the stabiliser trim wheel.
Summary
What to take into the exam Why power Hinge moments ∝ size × IAS². Pilot force limits set by certification.
Assisted Pilot shares load. Reversible, natural feel, no feel unit.
Fully powered Jack does it all. Irreversible, needs artificial feel and duplication.
PFCU Actuator, servo valve, follow-up. Ports re-covered: hydraulic lock.
Failure Pressure drop opens spring-loaded bypass: no lock, unit follows.
Feel Spring box: deflection only. Q feel: pitot − static. Return port never shut.
Feel trim Stabiliser trim resets the feel datum: hands-off flight.
A320 FBW 2 ELAC, 3 SEC, 2 FAC. Rudder and trim wheel mechanical back-up.
Chapter 10 · Powered Flying Controls and Fly-by-wire
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Hinge moments grow with surface size and the square of the indicated airspeed, and certification limits the force a pilot can be asked to apply. Power-assisted controls share the load; they are reversible, with natural feel and no feel unit. Fully powered controls do all the work; they are irreversible, so they need artificial feel and duplication. A powered flying control unit has an actuator, a servo valve and a follow-up, which re-covers the ports so a hydraulic lock holds the surface where it was put. If a system fails, the pressure drop opens a spring-loaded bypass so the dead unit follows the good one. A spring box gives feel with deflection only; a Q feel unit uses pitot minus static pressure to add feel with speed, and its return port is never fully closed. Feel trim resets the datum. And on the A320 there are two ELACs, three SECs and two FACs, with the rudder and stabiliser trim wheel as the mechanical back-up.