Aircraft Systems · Chapter 13
Pressurisation How a pressurised aircraft keeps its cabin near 8 000 ft while it flies at 40 000: differential pressure, the outflow valve, safety and inward relief valves, controllers, the flight profile, instruments and failures.
aircraft 37 000 ft cabin about 8 000 ft The cabin climbs gently while the aircraft climbs fast © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter thirteen is about pressurisation. At forty thousand feet the outside air pressure is less than a fifth of sea level, and nobody could stay conscious for long breathing it. So we seal the fuselage, pump air in, and let it out through a valve, keeping the cabin at the pressure you would find at about eight thousand feet. In this lesson you will learn the language of cabin altitude and differential pressure, how the fuselage copes with the load, how the outflow valve and its safety valves work, how the controller schedules the cabin through the flight, what the crew see on their instruments, and what happens when things go wrong.
Roadmap
Holding a cabin at 8 000 ft at 40 000 ft 1 · Why and the words Hypoxia, cabin altitude, differential, maximum and negative differential.
2 · Structure Max diff, hoop stress, fatigue, and which parts are pressurised.
3 · Control and safety Constant in, variable out; the outflow, safety, inward relief, dump and ditching valves.
4 · Controllers and profile Pneumatic and electronic controllers; taxi, climb, cruise, descent, landing.
5 · Instruments Cabin altimeter, cabin VSI, differential gauge and the 10 000 ft warning.
6 · Failures Valves failing open or shut, decompression, manual control, ground testing.
Exam focus Which way the valve moves, what each valve limits, cabin rates and their sums.
Links Lesson 12 supplied the conditioned air; lesson 18 covers oxygen.
Chapter 13 · Pressurisation
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our plan for pressurisation. First, why we pressurise and the vocabulary: cabin altitude, differential pressure, maximum and negative differential. Second, the structure: the maximum differential, the hoop stress it causes, fatigue, and which parts of the aircraft are inside the pressure hull. Third, how the cabin pressure is controlled, with a constant flow in and a variable flow out, and the valves that keep it safe. Fourth, the controllers and the flight profile, phase by phase. Fifth, the instruments the crew use. Sixth, failures: valves that stick, decompressions, manual control and ground testing. In exams you will be asked which way the outflow valve moves, what each safety device limits, and simple rate calculations, so we will practise all three.
Part 1 · Why pressurise
Why pressurise the cabin? Jets fly efficiently and above most weather at high altitude Without pressurisation: hypoxia , loss of concentration, unconsciousness, death Up to about 10 000 ft people cope; cabins are held at about 8 000 ft or lower Cabin 10 000 ft : crew on oxygen; cabin 14 000 ft : passengers on emergency oxygen High aircraft rates of climb and descent with only small cabin rates Compressed air is still about 21 % oxygen : what rises is the oxygen's partial pressure Why pressurise? 41000 Aircraft cruise: efficient, above most weather 14000 Passenger masks drop (cabin altitude) 10000 Cabin altitude warning: crew on oxygen 8000 Normal maximum cabin altitude 0 Sea level cabin aircraft Above about 10 000 ft, without extra oxygen: hypoxia
Chapter 13 · Pressurisation
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why pressurise at all? Modern aircraft operate more efficiently at high altitude, where the air is thin and the drag low, and up there they are above most of the weather. They can also climb and descend quickly. But the air pressure at forty thousand feet is so low that the body cannot take in enough oxygen: hypoxia, a lack of oxygen, causes loss of concentration, then unconsciousness, and finally death. Up to about ten thousand feet most people manage without too many problems, so cabin pressurisation systems are designed to give conditions equivalent to about eight thousand feet or lower. That way no oxygen equipment is needed except in an emergency. If the cabin altitude reaches ten thousand feet, the crew must be on oxygen, and at fourteen thousand the passengers must be on emergency oxygen. Note that compressing the air does not change its make-up: it is still about twenty one per cent oxygen, but at a higher pressure, which is what the lungs need.
Part 1 · The words
The vocabulary of pressurisation Cabin altitude The pressure altitude at which the cabin pressure would occur in the ISA. Not a height above the ground.
Differential pressure Cabin pressure minus outside (ambient) pressure, usually in psi. Positive when the cabin is higher.
Maximum differential The greatest authorised difference between inside and outside: a structural limit, typically 8 to 9 psi.
Negative differential Outside pressure higher than cabin pressure, e.g. descending below the cabin altitude. Limited by the inward relief valve.
Rate of change How fast the cabin altitude climbs or descends, in ft/min, shown on the cabin VSI.
Pressure cabin A cabin that can be held at a pressure higher than ambient: pressurisation.
Chapter 13 · Pressurisation
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us get the words exactly right, because exam questions turn on them. Cabin altitude is the pressure altitude at which the pressure inside the cabin would occur in the standard atmosphere. It is not the height of the cabin above the ground or above sea level. Differential pressure is cabin pressure minus outside pressure, usually given in p s i. The maximum differential is the greatest authorised difference between the inside of the fuselage and the outside, fixed by the strength of the structure, typically eight to nine p s i on large jets. A negative differential means the outside pressure is higher than the cabin pressure, for example if the aircraft descends below the cabin altitude. The rate of change is how fast the cabin altitude is climbing or descending. And a pressure cabin simply means a cabin that can be held at a higher pressure than the air outside.
Part 1 · The numbers
Pressure falls with altitude: the differential grows 0 2 4 6 8 10 12 14 16 0 5 10 15 20 25 30 35 40 45 Altitude (thousands of feet) Pressure (psi) cabin at 8 000 ft: 10.9 psi 6.6 7.8 8.3 ISA: 14.7 psi at sea level Differential (red) = cabin − outside Cabin held at 8 000 ft: 30 000 ft: 6.6 psi 37 000 ft: 7.8 psi 41 000 ft: 8.3 psi The higher the aircraft, the bigger the differential for the same cabin altitude.
Chapter 13 · Pressurisation
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph, computed from the standard atmosphere, is the key to the subject. The black curve is outside air pressure: about fourteen point seven p s i at sea level, falling to around two point six at forty one thousand feet. The green line is a cabin held at eight thousand feet, which is about ten point nine p s i. The red arrows are the differential, cabin minus outside. At thirty thousand feet it is about six and a half p s i, at thirty seven thousand nearly eight, and at forty one thousand about eight point three. So for the same cabin altitude, the higher the aircraft flies, the bigger the differential. Now the other way round: in level flight, if the cabin altitude rises, cabin pressure falls while outside stays the same, so the differential decreases. Raising the cabin from six thousand to eight thousand feet at thirty thousand feet, for example, cuts the differential from about seven point four to six point six.
Part 2 · Maximum differential
Maximum differential sets the ceiling Typical max diff for large jets: 8 to 9 psi (552 to 621 hPa); the exam range is about 7 to 9 psi It is a structural limit: what the cabin can safely sustain It fixes the maximum operating altitude at which the cabin can be held at 8 000 ft 6.4 psi: sea-level cabin to about 15,000 ft ; 8.6 psi: to about 22,400 ft More max diff: higher flight, but a heavier hull What a bigger max diff buys Max diff Sea-level cabin up to 8 000 ft cabin up to 6.4 psi ≈ 15,000 ft ≈ 29,200 ft 8.6 psi ≈ 22,400 ft ≈ 43,300 ft ISA; ceiling where outside = cabin − max diff Max diff is a STRUCTURAL limit: the hull is designed for it (typically 8 to 9 psi on big jets) It fixes the maximum operating altitude at which the cabin can still be held at 8 000 ft Higher max diff = higher, more efficient flight, but a heavier fuselage
Chapter 13 · Pressurisation
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The maximum differential is a structural limit: the largest pressure difference the cabin is designed to sustain. On large jet transports it is typically eight to nine p s i. That number sets how high the aircraft can fly while still holding a comfortable cabin. Let us work it out from the standard atmosphere. With a maximum differential of six point four p s i, the cabin can be kept at sea level pressure only up to about fifteen thousand feet. With eight point six p s i, up to about twenty two thousand four hundred. If we accept the usual eight thousand foot cabin, the same two aircraft can go to about twenty nine thousand and forty three thousand feet respectively. So if the maximum operating altitude is limited by the pressure cabin, the limiting factor is the maximum differential that the structure can sustain. Designers could build stronger hulls, but the weight penalty would be unacceptable.
Part 2 · Structure
Hoop stress and fatigue The differential stretches the skin round the fuselage: hoop stress σ = ΔP × r ÷ t: about 70 MPa for 8.3 psi, 1.95 m radius, 1.6 mm skin Applied and removed every flight : one pressurisation cycle Fatigue life of the fuselage is based on the number of pressurisation cycles A lower max diff (8 000 ft cabin, not sea level) means less stress, less weight Hoop stress in the fuselage skin ΔP hoop tension σ = ΔP × r ÷ t ΔP 8.3 psi (57 kPa) r 1.95 m t 1.6 mm σ ≈ 70 MPa Every flight: one full cycle of this stress, on and off pressurisation cycles → fatigue life of the hull
Chapter 13 · Pressurisation
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
What does the differential do to the structure? The air inside pushes outwards on every square inch of skin, trying to stretch the fuselage like a balloon. The tension that runs round the circumference is called hoop stress, and it equals the differential times the radius divided by the skin thickness. Let us put numbers in: eight point three p s i, a radius of one point nine five metres and a skin one point six millimetres thick give about seventy megapascals in the skin. Every flight applies that stress and then removes it again on landing: one pressurisation cycle. Repeated thousands of times, it causes fatigue, which can ultimately lead to structural failure. That is why the fatigue life of a fuselage is counted in pressurisation cycles, not hours. Keeping the maximum differential as low as practical, by settling for an eight thousand foot cabin rather than sea level, reduces the stress and the fatigue, and saves structural weight and cost.
Part 2 · The pressure hull
Pressurised and unpressurised areas Pressurised: flight deck , passenger cabin and cargo compartments Bounded by the forward and aft pressure bulkheads Unpressurised: nose wheel and main wheel bays , radome , tail cone Wings and tail surfaces are outside the hull Wheel wells are a dent in the hull: their walls carry the differential Pressurised and unpressurised areas forward pressure bulkhead aft pressure bulkhead flight deck + cabin cargo holds wells radome tail cone Pressurised • flight deck • passenger cabin • cargo compartments Unpressurised • nose (radome) and nose wheel bay • main wheel bays • tail cone, wing and tail
Chapter 13 · Pressurisation
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Which parts of the aircraft are actually pressurised? The pressure hull runs from the forward pressure bulkhead, just behind the radar in the nose, to the aft pressure bulkhead behind the rear galley. Inside it are the flight deck, the passenger cabin and the cargo compartments under the floor, all normally pressurised. Outside it are the radome, the nose wheel bay and the main wheel bays, the tail cone and of course the wings and tail. Look at the scene: the wheel wells form a dent in the bottom of the hull, so their walls are pressure walls, carrying the differential, while the wells themselves are at outside pressure. A favourite exam question asks whether the main and nose wheel bays are pressurised: they are both unpressurised.
Part 3 · Control
Constant inflow, variable outflow A constant mass flow enters from the air-conditioning system (mass flow controller) Air leaves through the outflow (discharge) valves at a varying rate Valve closes : less outflow, cabin pressure rises ; valve opens : pressure falls Positioned by the pressure controller in auto, by the crew in manual In the cruise the outflow valve acts as a thrust recovery nozzle Constant in, variable out CABIN constant mass flow from the packs outflow valve Valve CLOSES less air out cabin pressure RISES cabin altitude FALLS differential RISES Valve OPENS more air out cabin pressure FALLS cabin altitude RISES differential FALLS
Chapter 13 · Pressurisation
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Cabin pressure is controlled by a simple principle: a constant mass flow of air comes in, and the rate at which it is let out is varied. The constant inflow is supplied by the air-conditioning system through the mass flow controller. The air leaves through the outflow valves, also called discharge valves, usually low down in the rear fuselage. Closing the outflow valve reduces the outflow, so the cabin pressure rises; opening it increases the outflow and the pressure falls. In automatic mode the pressure controller positions the valve; in manual the crew do it. During the cruise the outflow valve is shaped to form a thrust recovery nozzle, so the escaping air gives back a little of the energy it cost. So modern pressurisation systems use constant inflow and variable outflow, never the other way round.
Part 3 · Valve logic
Which way is the outflow valve moving? Differential increasing : outflow valve closing (climb) Differential constant : valve not moving , normally partly open (cruise) Differential decreasing : valve opening (descent) Level flight: cabin pressure rises = differential rises ; cabin altitude rises = differential falls Holds because the inflow is constant Read the valve from the differential Differential INCREASING → outflow valve CLOSING climb Differential CONSTANT → valve NOT moving (partly open) cruise Differential DECREASING → outflow valve OPENING descent Because the mass flow in is constant, the outflow valve alone sets the cabin pressure
Chapter 13 · Pressurisation
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the most useful rule in the chapter. Because the mass flow in is constant, you can tell what the outflow valve is doing just by watching the differential. Watch the scene. In the climb the differential is increasing, so the outflow valve is closing. In the cruise the differential is constant, so the valve is not moving: it sits partly open, letting out exactly the air the packs are putting in. In the descent the differential is decreasing, so the valve is opening. Two more consequences for level flight: if the cabin pressure increases, the differential increases; and if the cabin altitude is raised, which means the cabin pressure is lowered, the differential decreases. Remember, the valve is never fully closed in normal flight: if it were, the cabin pressure would rise until a safety valve opened.
Part 3 · Safety devices
The safety valve and the inward relief valve CABIN (inside) OUTSIDE Safety (outward relief) valve opens at max diff + 0.25 psi limits POSITIVE differential Inward relief valve opens when outside exceeds inside by 0.5 to 1.0 psi limits NEGATIVE differential Both: simple, mechanical, duplicated Mounted above the flotation line
Chapter 13 · Pressurisation
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every pressurisation system must have safety devices in addition to the outflow valve. The first is the safety valve, a simple mechanical outward relief valve. If the outflow valve or its controller fails and the differential keeps rising, the safety valve lifts outwards when the pressure reaches the maximum differential plus about a quarter of a p s i, venting cabin air so that the structural limit can never be exceeded. The second is the inward relief valve, also called the inward vent. If the outside pressure ever exceeds the cabin pressure by about half to one p s i, for example in a rapid descent below the cabin altitude, it opens inwards and lets outside air in, so the fuselage is not crushed. Both are simple, mechanical, spring-loaded shut and independent of the controller, they may be separate or combined in one unit, they are duplicated, and they are mounted above the flotation line.
Part 3 · The order of events
The differential scale: who acts when -1 0 1 2 3 4 5 6 7 8 9 10 Differential pressure, cabin − outside (psi) normal working range: outflow valve in control Max diff (example 8.6) controller holds it here Safety valve opens max diff + 0.25 Pre-pressurised taxi and touchdown 0.1 Inward relief opens −0.5 to −1.0 structure Sequence as the differential rises: the outflow valve works first; only if it fails (or is closed) does the safety valve open. A negative differential (outside higher than inside, e.g. a rapid descent below cabin altitude) is relieved by the inward relief valve.
Chapter 13 · Pressurisation
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put all the numbers on one scale of differential pressure. In normal operation everything happens in the green band, from zero up to the maximum differential, say eight point six p s i, and the outflow valve is in charge. The pressure controller will not let the differential go higher: at the maximum it switches to maximum differential control. Only if the outflow valve fails shut, or its controller misbehaves, does the differential rise further, and at about a quarter of a p s i above the maximum the safety valve opens. So in the sequence of operation, the outflow valve acts first and the safety valve after it, at a higher differential. At the other end, a little above zero, is the point one p s i of pre-pressurisation used on the ground. And below zero, at about minus half to minus one p s i, the inward relief valve opens to stop the negative differential growing.
Part 3 · More safety devices
Dump valve, ditching control and blow-out panels Dump valve Manually operated. Lets the crew reduce the cabin differential to zero quickly: emergency depressurisation (e.g. smoke). On some aircraft also the outlet in manual control.
Ditching control Closes all the outflow (discharge) valves and other openings below the waterline, so less water enters after a forced landing on water.
Blow-out (vent) panels Between cabin and cargo holds. If a hold decompresses (e.g. a cargo door opens), they open to equalise pressure so the floor does not collapse.
Chapter 13 · Pressurisation
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three more devices complete the safety picture. The dump valve is manually operated: it lets the crew reduce the cabin pressure to ambient quickly, an emergency depressurisation, for example to clear smoke. On some aircraft with pneumatic discharge valves it also serves as the air outlet when the system is in manual control. The ditching control closes all the outflow valves, and other openings below the waterline, so that after a forced landing on water as little water as possible enters the cabin. Note the contrast: the dump valve opens, the ditching control closes. Finally, blow-out panels, or vent panels, sit in the floor sidewalls between the passenger cabin and the cargo holds. If a hold suddenly decompresses, for example because a cargo door opens in flight, they open to equalise the pressure above and below the floor, so that the floor, which carries the control runs, does not collapse.
Part 4 · Controllers
Pressure controllers Types: pneumatic , electro-pneumatic and, on most modern aircraft, electronic A pneumatic controller senses cabin pressure and static (ambient) pressure Crew select the required cabin altitude and rate of change Outflow valves are biased fully open on the ground Cabin pressure can be controlled automatically or manually ; a ditching control may be fitted A pneumatic pressure controller controller cabin pressure capsule static pressure capsule from static vent metering valve signal outflow valve Crew selectors cabin altitude rate of change barometric set • Senses cabin AND static pressure • Positions the outflow valve to give the selected rate and differential; valves biased fully open on the ground
Chapter 13 · Pressurisation
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The pressure controller is the brain of the system. Older controllers are pneumatic: capsules and metering valves sense both the cabin pressure and the outside static pressure, and the crew set knobs for the required cabin altitude and the rate of change. Electro-pneumatic controllers add electrical signals, and most modern aircraft use fully electronic controllers. Whatever the type, as the cabin pressure changes, the controller sends a signal to the outflow valves, positioning them to release air at the pre-selected rate, to achieve the required differential and, eventually, stabilise at the maximum differential if the aircraft climbs high enough. On the ground the outflow valves are biased fully open. Remember that cabin pressure can be controlled either automatically or manually; and some controllers include a ditching control that shuts all the discharge valves.
Part 4 · A modern system
Electronic pressurisation control Static pressure (air data) Cabin pressure sensor Air / ground logic (squat switches) Thrust levers + doors (pre-pressurisation) Landing field elevation (from FMS or panel) Controller 1 ACTIVE Controller 2 STANDBY automatic changeover on failure Outflow valve 2 AC motors DC motor auto 1 / auto 2 manual Overhead panel MODE: AUTO / MAN MAN V/S: UP / DN LDG ELEV DITCHING Selecting MANUAL locks out the automatic functions; the crew drive the valve through the DC motor
Chapter 13 · Pressurisation
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a typical modern electronic system. Two automatic controllers are fitted, but only one works at a time: the other is on standby, and takes over automatically if the active one fails. Their inputs are the aircraft static pressure from the air data system, the cabin pressure, and the air and ground logic from the landing gear. If pre-pressurisation is part of the schedule, they also need the thrust lever positions and the door warning system. The crew panel is on the overhead panel, remote from the controllers. The outflow valve has two A C motors, one for each automatic controller, and a D C motor for manual or emergency operation. Selecting manual locks out all the normal automatic functions; the crew then position the outflow valve with the manual switch through the D C motor, watching their instruments. The pilot normally only sets the landing field elevation and checks the profile.
Part 4 · The flight profile
The pressurisation profile: a computed flight 0 5 10 15 20 25 30 35 40 0 10 20 30 40 50 60 70 80 90 Time (minutes) Altitude (thousands of feet) climb cruise descent aircraft FL370 cabin ≈ 7900 ft (differential 7.8 psi) cabin climbs ≈ 440 ft/min cabin descends ≈ 290 ft/min Taxi: FLIGHT selected, pre-pressurised to 0.1 psi (cabin ≈ 190 ft below field) Climb: cabin rate in proportion to aircraft rate Cruise: isobaric; max diff control if limit reached Descent: cabin ≤ 300 ft/min, lands at field − 200 ft (0.1 psi), then dumped
Chapter 13 · Pressurisation
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us fly a computed flight from a sea-level airport, up to flight level three seven zero and back. During the taxi the crew select FLIGHT, and the cabin is pre-pressurised to a differential of point one p s i, which puts the cabin about two hundred feet below the field. That makes the transition to pressurised flight gradual, with no pressure surge on rotation and no fumes drawn in. After take-off the controller switches to proportional control: the cabin climbs at a rate in proportion to the aircraft's, here about four hundred and forty feet a minute while the aircraft climbs at two thousand, so cabin pressure falls, but at a lower rate than outside. In the cruise it switches to isobaric control, holding a constant differential, with the cabin at about eight thousand feet. In the descent it returns to proportional control, about three hundred feet a minute down, so cabin pressure increases more slowly than outside, arriving at point one p s i at touchdown.
Part 4 · Phase by phase
What the controller does in each phase Phase Mode Outflow valve Cabin Taxi FLIGHT selected: pre-pressurise Closing slightly 0.1 psi differential Take-off and climb Proportional Closing Climbs at 300 to 500 ft/min Cruise Isobaric (constant differential) Steady, partly open Constant; small level changes of 500 to 1 000 ft absorbed High cruise Maximum differential control Opening as needed to cap the differential Rises if the aircraft climbs further Descent Proportional Opening Descends at about 300 ft/min Touchdown Ground logic, then GROUND Driven fully open 0.1 psi, then zero
Older aircraft reduce the differential to zero at touchdown; newer ones land at 0.1 psi and dump it once on the ground.
Chapter 13 · Pressurisation
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the phases side by side. During the taxi, with FLIGHT selected, the system pre-pressurises to point one p s i. From take-off, proportional control: the outflow valve closes progressively and the cabin climbs at three to five hundred feet per minute. In the cruise, isobaric control holds a constant differential; the valve is steady and partly open, and small changes of altitude, five hundred to a thousand feet, are absorbed without changing the cabin pressure. If a much higher level is needed the selected cruise altitude must be reset. If the maximum differential is reached, the controller will not allow any further increase: that is maximum differential control, and if the aircraft climbs further the outflow valve opens and the cabin climbs with it. In the descent, proportional control again, about three hundred feet per minute. After touchdown, ground mode drives the valves fully open and the differential falls to zero.
Part 4 · Rates
Cabin rates of change Normal limits: cabin climb 500 ft/min , cabin descent 300 ft/min Limited by passenger comfort : ear physiology, especially with colds The descent rate matters most: rising pressure is harder on the ears 0.16 psi/min ≈ 300 ft/min near sea level Aircraft 0 → 16 000 ft at 1 000 ft/min and cabin 0 → 8 000 ft at 500 ft/min: both take 16 min Rates of change: worked examples Example 1 Aircraft: 0 → 16 000 ft at 1 000 ft/min = 16 min Cabin: 0 → 8 000 ft at 500 ft/min = 16 min → both arrive together Example 2 Aircraft: 0 → 30 000 ft at 1 500 ft/min = 20 min Cabin: 0 → 8 000 ft at 500 ft/min = 16 min Normal maximum cabin rates (comfort): climb 500 ft/min, descent 300 ft/min Descent is the more critical: the ears equalise less easily as pressure rises 0.16 psi/min ≈ 300 ft/min near sea level
Chapter 13 · Pressurisation
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
How fast may the cabin altitude change? The limits come from passenger comfort, especially the ears. Normal maximum rates are about five hundred feet per minute in the climb and three hundred feet per minute in the descent. The descent is the more critical: as the pressure rises, air has to get back into the middle ear through the Eustachian tube, which is harder, especially with a cold, than letting it out. A rate of point one six p s i per minute is roughly three hundred feet per minute near sea level. Now two worked examples. An aircraft climbs from sea level to sixteen thousand feet at a thousand feet per minute: sixteen minutes. Its cabin climbs to eight thousand at five hundred: also sixteen minutes, so they arrive together. Another climbs to thirty thousand at fifteen hundred, which takes twenty minutes, while its cabin climbs to eight thousand at five hundred, which takes sixteen: the cabin pressure decreases gradually over sixteen minutes.
Part 5 · Instruments
The cabin instruments and the warning Cabin altimeter : cabin pressure shown as an equivalent altitude Cabin VSI : the rate at which the cabin climbs or descends (a special gauge)Differential gauge : inside minus outside absolute pressure, in psiAbove 10 000 ft cabin : aural and visual warning (horn, red light, ECAM or EICAS) Cabin pressure rising shows as a cabin descent on the VSI The three cabin instruments 8 000 ft Cabin altimeter 0 ft/min Cabin VSI 7.8 psi Differential Cabin altimeter: cabin pressure shown as altitude Cabin VSI: rate the CABIN climbs or descends (cabin pressure rising = cabin DESCENDING) Differential gauge: cabin minus outside, psi (stuck at max diff + 0.25 = safety valve in control) Plus: horn and red warning above 10 000 ft cabin
Chapter 13 · Pressurisation
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three instruments are the minimum for a pressurisation system. The cabin altimeter reads cabin pressure but is calibrated as the equivalent cabin altitude. The cabin vertical speed indicator, a special gauge separate from the aircraft V S I, shows the rate at which the cabin is climbing or descending. The differential pressure gauge shows the difference between the absolute pressures inside and outside, in p s i. If the controller or outflow valve fails shut, this gauge will show the safety valves holding the differential at the structural maximum. Now watch the scene: in the cruise at thirty thousand feet, the outflow valve fails open. The cabin VSI swings to a high rate of climb, the cabin altitude rises, and the differential falls. When the cabin passes ten thousand feet, the warning comes on, with a horn and a red light, or a caption on the E CAM or EICAS. And remember: if cabin pressure rises, the VSI shows a cabin descent.
Part 5 · Cabin altitude
Cabin altitude: what happens when 8 000 ft : normal maximum cabin altitude10 000 ft : horn and red warning ; crew on oxygen, find the fault or descendOn some types, about 13 000 ft : outflow valves driven shut automatically About 14 000 ft : passenger oxygen masks deploy automatically The early warning gives time to fix the fault before the masks drop Cabin altitude: what happens when 14,000 ft Passenger masks drop automatically 13,000 ft Some types: outflow valve driven shut 10,000 ft Horn + red warning; crew on oxygen 8,000 ft Normal maximum cabin altitude
Chapter 13 · Pressurisation
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us climb the cabin altitude ladder in a pressurisation failure. Eight thousand feet is the normal maximum cabin altitude. At ten thousand feet the crew get an aural and visual warning, a horn and a red light, or a red caption on the electronic display. The crew go on oxygen and try to find and correct the problem, which may stop the cabin climbing further and save the passengers from having their masks drop. If the problem cannot be solved, on some types the controller drives the outflow valves shut at around thirteen thousand feet to minimise the loss of cabin air. If the cabin altitude still reaches about fourteen thousand feet, the passenger oxygen masks are deployed automatically from the passenger service units. The exact figures vary a little by type, but ten thousand for the warning and fourteen thousand for the masks are the ones to remember.
Part 6 · Failures
Failures and what the gauges show Failure (level cruise) Cabin pressure Differential Cabin VSI / altitude Outflow valve fails open Decreases Decreases Climb; cabin altitude increases Outflow valve fails closed Increases until the safety valve lifts Increases to max diff + 0.25, then held by the safety valve Descent, then zero; altitude decreases Slow leak or one pack lost Falls slowly if inflow is short Falls slowly Small steady climb, e.g. 300 ft/min: pressure will fall to ambient if unchecked Rapid decompression Falls to ambient in seconds Falls to zero Very high rate of climb Rapid descent below cabin altitude Lower than outside Negative Inward relief valve opens
Rule of thumb: cabin pressure and differential move together; cabin altitude moves the other way.
Chapter 13 · Pressurisation
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us use the rules to read failures, all in level cruise. If the outflow valve fails open, more air leaves than enters: the cabin pressure decreases, the differential decreases, the cabin VSI shows a climb and the cabin altitude increases. If it fails closed, the pressure rises until the safety valve lifts at the maximum differential plus a quarter of a p s i, which then holds it there; the cabin VSI briefly shows a descent. The cabin will not be damaged, and the packs need not be switched off. A slow leak, or the loss of a pack with nothing to replace it, shows as a small steady cabin climb, for example three hundred feet per minute in level flight: if nothing is done the pressure will eventually fall to ambient. A rapid decompression sends everything to its limit in seconds. And descending fast below the cabin altitude gives a negative differential, relieved by the inward relief valve.
Part 6 · Decompression
Slow and rapid decompression Slow : leaks, a failed seal or pack; seen on the gauges and the cabin VSIRapid : a bang, rushing air, flying debris, ear painSudden mist (fog) in the cabin: air expands, cools, its water condenses Crew: oxygen masks on , then emergency descent A decompressed cargo hold : vent panels equalise across the floor Decompression Slow leak, failed seal, pack loss cabin VSI shows a climb cabin altitude creeps up diff falls may go unnoticed: watch the gauges and the warning Rapid / explosive bang, rush of air, debris sudden MIST (fog): air expands and cools, water condenses temperature drop, ear pain masks drop at 14 000 ft Crew: oxygen masks ON first, then emergency descent to 10 000 ft or minimum safe altitude Time of useful consciousness is very short at high altitude Cargo hold decompresses (door open in flight)? Vent (blow-out) panels in the floor sidewalls equalise cabin and hold, so the floor does not collapse
Chapter 13 · Pressurisation
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
A decompression is the loss of cabin pressure, and it can be slow or rapid. A slow decompression, from a leaking door seal, a failed valve or a lost pack, may give no physical clue at all: the crew notice it on the cabin VSI and altimeter, or when the ten thousand foot warning sounds. A rapid, or explosive, decompression is unmistakable. There is a bang, a rush of air towards the hole carrying dust and loose objects, pain in the ears, and the cabin suddenly fills with mist. That mist is the giveaway: the air expands so fast that it cools sharply, and its water vapour condenses into fog. The same thing happens if a cabin is rapidly depressurised during a ground test. The crew's first action is to put on their own oxygen masks, then begin an emergency descent. And if a cargo hold decompresses, vent panels in the floor equalise the pressure between cabin and hold.
Part 6 · Manual control
Manual pressurisation control Selecting MANUAL locks out the automatic functions The crew move the outflow valve with a switch, via the DC motor The rate of change is set with the rate change selector or valve switch Monitor: cabin altimeter , cabin VSI , valve position indicator , differential Take care that climb and descent rates stay safe and comfortable Manual control Panel MODE: MAN V/S: UP · DN rate change selector / valve switch Outflow valve DC motor Auto functions locked out; crew position the valve Watch: cabin altimeter, cabin VSI, valve position indicator, differential gauge Keep the cabin rates safe and comfortable: 500 ft/min up, 300 ft/min down Older pneumatic systems: dump valve used as the outlet
Chapter 13 · Pressurisation
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
If both automatic controllers fail, the crew can control the pressurisation manually. Selecting manual locks out all the normal automatic functions. The crew then position the outflow valve themselves with the manual control switch, which drives the valve through its D C motor; on simpler systems a rate change selector sets how fast the cabin altitude changes. They monitor the cabin altimeter, the cabin VSI, the outflow valve position indicator and the differential gauge. Manual control does not need an extra crew member, but it does need care: the climb and descent rates must be kept safe and comfortable, about five hundred feet per minute up and three hundred down, because nothing is now limiting them automatically. On some older aircraft with pneumatic discharge valves, the dump valve is used as the air outlet in manual control.
Part 6 · On the ground
Landing, ground logic and the cabin altimeter Squat (landing gear) switches inhibit pressurisation on the groundAfter touchdown they bring the differential to zero ; outflow valves fully open GROUND selected: valves driven fully open to equalise inside and outside A cabin altimeter set to QFE reads zero on the ground Controller set to field elevation with QFE (zero): cabin unpressurised on landing On the ground squat switch: ON GROUND outflow valve fully OPEN 0 psi differential 0 ft cabin alt (QFE) Ground logic inhibits pressurisation and drives the differential to ZERO • Outflow valves biased fully open on the ground • Cabin altimeter on QFE reads ZERO on the ground • Landing altitude zero against QFE: cabin unpressurised on landing
Chapter 13 · Pressurisation
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the ground the aircraft must not stay pressurised: a door could be forced open with dangerous force. So inhibiting microswitches on the landing gear, the squat switches, tell the system that the aircraft is on the ground. After touchdown they stop the pressurisation and bring the differential to zero, and when the crew select GROUND the outflow valves are driven fully open to equalise the cabin and the outside. On older aircraft the controller simply reduces the differential to zero at touchdown. One more ground fact: if QFE is set on the cabin altimeter, it reads zero on the ground, exactly like the aircraft altimeter. And if the controller's landing altitude is set to zero against QFE, the cabin arrives at field pressure, so it is unpressurised on landing. Those questions appear regularly.
Part 6 · Maintenance
Ground testing of the pressure hull Top row: when the tests are done. Bottom row: what they check.
Initial proof test When the aircraft is built.
Maintenance manual At the intervals it specifies.
After a malfunction Actual or suspected system faults.
After repairs Repairs or modifications to the pressure hull.
Functioning General functioning and temperature control.
Controllers Operation of the controllers and normal max diff control.
Safety valve Opens at the structural maximum differential.
Leak rate The hull holds pressure within limits.
Chapter 13 · Pressurisation
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pressurisation systems are checked on the ground at intervals, to make sure there are no serious leaks and that the controllers and safety devices work. The tests are carried out at the initial proof pressure test when the aircraft is built, whenever the maintenance manual specifies, after any actual or suspected malfunction, and after repairs or modifications to the pressure hull. The procedure is specific to each type, but it may establish four things: the general functioning and temperature control; that the controllers work and hold the normal maximum differential; that the safety valve opens at the structural maximum; and the leak rate of the hull. If the cabin is suddenly depressurised during such a test, you would see water precipitating as mist, for the same reason as in a decompression in flight.
Summary
Pressurisation: the essentials Words Cabin altitude: ISA pressure altitude of the cabin pressure. Differential = cabin − outside. Max diff: structural, 8 to 9 psi. Negative differential: outside higher.
Why and structure Cabin ≤ 8 000 ft; warning at 10 000; masks 14 000. Hoop stress σ = ΔP r / t; fatigue counted in pressurisation cycles. Wheel bays, radome, tail cone unpressurised.
Control Constant inflow, variable outflow. Diff rising: valve closing; steady: partly open; falling: opening. Thrust recovery nozzle in cruise.
Safety devices Safety valve: outward, max diff + 0.25 psi, after the outflow valve. Inward relief: 0.5 to 1 psi negative. Dump: manual, to zero. Ditching: closes outflow valves. Vent panels in the floor.
Profile Taxi 0.1 psi; proportional climb 300 to 500 ft/min; isobaric cruise; max diff control; descent 300 ft/min; land at 0.1 psi; ground logic opens the valves.
Instruments and failures Cabin altimeter, cabin VSI, differential gauge, 10 000 ft warning. Valve open: cabin climbs, diff falls. Valve shut: safety valve holds. Mist = rapid decompression.
Chapter 13 · Pressurisation
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. Cabin altitude is the standard-atmosphere pressure altitude of the cabin pressure, and the differential is cabin minus outside, with a structural maximum of eight to nine p s i that sets the ceiling. The cabin is kept at or below eight thousand feet, with a warning at ten thousand and masks at fourteen thousand. Hoop stress cycles every flight, so fatigue life is counted in pressurisation cycles. Pressure is controlled by constant inflow and variable outflow: a rising differential means the valve is closing. The safety valve limits positive differential at a quarter p s i above the maximum, the inward relief valve limits negative differential, the dump valve opens and the ditching control closes. The profile runs from point one p s i on the taxi, through proportional climb, isobaric cruise and proportional descent. And on the instruments: if the outflow valve opens, the cabin climbs and the differential falls.