Aircraft Systems · Revision
Revision and Exam Practice The numbers, rules and traps that aircraft systems papers test again and again, with a full set of revision questions.
cabin 8000 ft VP = 9 √P 3000 psi +2.5 g 85 kt 8.6 psi 10 min 90 s 14 000 ft −47 °C numbers · rules · traps © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the revision chapter of the aircraft systems course. Systems papers are full of numbers and rules: pressures, temperatures, seat counts, altitudes, colours, and which way a valve moves when something fails. The same traps appear again and again. In this chapter we walk through the whole syllabus, one block per page: the airframe and hydraulics, the landing gear with tyres and brakes, the flight controls, the air systems from bleed air to de-icing, the emergency equipment, oxygen and fire protection, and finally fuel. On every page look for the number to remember and the trap. Then work through the quiz, the question bank and the mixed revision paper at the end.
How to use this chapter
The whole systems syllabus on one page each Each page gathers one block of the syllabus: the numbers, the rules and the classic traps. Every revision question links back to one of them.
Airframe and hydraulics Loads and design philosophy, materials, Pascal and F = P × A, fluids, accumulators and the valves.
Landing gear Oleos, locks and lights, emergency extension, tyres and aquaplaning, brakes, anti-skid and autobrake.
Flight controls Sense of movement, adverse yaw, rigging, tabs, high lift devices, spoilers, powered controls and fly-by-wire.
Air systems Bleed air, packs, pressurisation and its failures, ice and rain protection, ground de-icing.
Emergency equipment Exits, lighting and slides, rafts and beacons, oxygen, fire detection and extinguishers.
Fuel Fuel grades and contamination, tanks, pumps, gauging and refuelling. Then the traps, the method and the questions.
Chapter 23 · Revision and Exam Practice
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This revision chapter squeezes the whole aircraft systems syllabus onto about twenty pages, in six blocks. First the airframe and hydraulics: loads and design philosophy, materials, Pascal’s law, fluids, accumulators and all the valves. Second the landing gear, with tyres and aquaplaning, brakes, anti-skid and autobrake. Third the flight controls, from cables and tabs to fly-by-wire. Fourth the air systems: bleed air, the packs, pressurisation and its failures, ice protection and ground de-icing. Fifth the emergency equipment, oxygen and fire. And last, fuel. On every page look for three things: the number to remember, the rule, and the trap the examiner likes to set. After the last page come the quiz, the question bank and a mixed revision paper, each question linked back to the page that answers it.
Structures and airframe
Loads, design philosophy and materials Limit load: transport +2.5 g ; ultimate = limit × 1.5 = 3.75 g, carried without collapse Pressure hull: hoop stress = 2 × axial ; fatigue life counted in pressurisation cycles Safe life : replace at the proven life · fail-safe : other load paths · damage tolerant : load spread, slow cracks, inspectWing in flight: upper skin in compression ; bending greatest at the root; wing fuel used last Intergranular corrosion is the most dangerous; gear designed for 10 ft/s at max landing massFlutter: mass balance ahead of the hinge ; aileron reversal at high speed , fully powered controls Design loads, transport aeroplane 0 g 1 g 2 g 3 g 4 g Limit load +2.5 g: no permanent set Ultimate load × 1.5 = 3.75 g: no collapse Pressure hull hoop stress axial stress σ hoop = ΔP·r ÷ t = 2 × σ axial fatigue: counted in cycles How likely may a failure be? (per flight hour) Minor 10⁻³ probable Major 10⁻⁵ remote Hazardous 10⁻⁷ extremely remote Catastrophic 10⁻⁹ extremely improbable
Chapter 23 · Revision and Exam Practice
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The airframe block is mostly definitions and a few numbers. A transport aircraft is designed to a limit load of plus two point five g, the largest load expected in service, and the ultimate load is one and a half times that, three point seven five g, which the structure must carry without collapse. In the pressure hull the hoop stress is twice the axial stress, and fuselage fatigue life is counted in pressurisation cycles. Keep the three philosophies apart: safe life means replace the part at its proven life; fail-safe means another load path takes over; damage tolerant spreads the load so cracks grow slowly and are found at inspections. In flight the upper wing skin is in compression. Intergranular corrosion is the most dangerous kind because little shows on the surface. And a catastrophic failure must be extremely improbable: about one in a thousand million per flight hour.
Hydraulic principles
Pascal, F = P × A, fluids and the accumulator Pascal: pressure acts equally everywhere in a confined liquid; no restriction, no pressure F = P × A ; work in = work out: twice the area, twice the force, half the travel Mineral fluid red , neoprene seals, flammable · phosphate ester purple , butyl seals, fire resistant · never mix Reservoir pressurised against cavitation and foaming ; the stack pipe keeps a reserve for the hand pump Accumulator gauge reads system pressure ; it shows the pre-charge only when the system is depressurised Unbalanced jack: more force extending ; same pressure both sides → it extends Accumulator, pre-charge 1000 psi (Boyle) 0 500 1000 1500 2000 2500 3000 0 25 50 75 100 System pressure (psi) Share of volume (%) gas ⅓ fluid ⅔ below the pre-charge: no fluid enters P × V = constant Unbalanced jack at 3000 psi cap side 10 in² rod side 10 − 4 = 6 in² rod 4 in² Extend: 3000 × 10 = 30 000 lbf Retract: 3000 × 6 = 18 000 lbf Same P both sides: extends with P × rod area
Chapter 23 · Revision and Exam Practice
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Hydraulics questions rest on two ideas. Pascal: in a confined liquid the pressure is the same everywhere, and the pump only makes flow; the load decides the pressure. And force equals pressure times area, so a piston with twice the area gives twice the force but moves half as far, because the same volume of fluid moves. Learn the fluids by colour and seal: mineral fluid is red with neoprene seals and burns; phosphate ester is purple with butyl seals and resists fire; never mix them. Now the accumulator, the favourite trap. With a pre-charge of one thousand psi and the system at three thousand, the gas is squeezed to one third of the volume, two thirds is fluid, and the accumulator gauge reads three thousand, the same as the system gauge. You only see the pre-charge with the system depressurised. Finally, an unbalanced jack pushes harder extending, because the rod takes area from the other side.
Hydraulic components
Which valve does what Valve What it does, and the trap Full-flow relief valve Downstream of the pump; passes the whole pump output if the cut-out or pump control fails; fully open about 10 % above system pressure Thermal relief valve In lines isolated by non-return valves or a neutral selector (hydraulic lock): relieves the pressure rise from heating Priority (pressure maintaining) Shuts off secondary services when pressure falls, so the flying controls keep working Pressure-reducing valve Lowers system pressure for one service, typically the wheel brakes One-way restrictor In the gear UP line : meters fluid leaving the jack so the gear does not extend too fast Shuttle valve Two supplies, one service (normal and alternate brakes, emergency gear); moves only when the alternate is pressurised Sequence valve One action finished before the next: doors open before the gear moves Hydraulic fuse Closes on excess flow or volume, upstream of a service that might leak; wheel brakes always have one
Also: the automatic cut-out valve idles a fixed-volume pump (fast cycling = leaks or low pre-charge); a PTU moves power, not fluid; the RAT powers the flying controls, never the gear.
Chapter 23 · Revision and Exam Practice
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The hydraulic valves are a list you must know cold, because the options in a question are usually the names of other valves. The full-flow relief valve sits after the pump and can pass the whole pump output if the cut-out valve or the pump control fails. Thermal relief valves protect lines that are isolated, where trapped fluid would otherwise burst something as it warms. The priority valve keeps the essential services, such as the flying controls, working when the pressure falls. The pressure-reducing valve lowers system pressure for the brakes. A one-way restrictor in the gear up line slows the extension. A shuttle valve lets two supplies feed one service, and only moves when the alternate supply is pressurised. A sequence valve makes sure the doors open before the gear moves. And a hydraulic fuse closes when too much fluid flows; it does not rupture. Below the table: the power transfer unit moves power, not fluid, and the ram air turbine never lowers the gear.
Landing gear
Struts, locks, lights and emergencies Oleo: nitrogen is the spring; oil through the orifice damps both compression and extension Main units just aft of the CG carry about 90 % ; the nose wheel must centre before retraction Shimmy: oscillation about the vertical axis , worn torque links; cure: shimmy damper Downlock over-centre ; uplock spring applied, hydraulically released; restrictor slows extension Lights: green down and locked · red in transit or disagree · none up and locked Squat switch locks the lever on the ground; emergency: free fall or nitrogen via shuttle valves Gear position lights NOSE LEFT RIGHT Down and locked NOSE LEFT RIGHT In transit / disagree NOSE LEFT RIGHT Up and locked Sequences and safeguards UP downlocks release legs retract uplocks catch doors close DOWN doors open uplocks release legs fall (restrictor) downlocks engage Sequence valve: doors fully open before the main gear moves. Squat switch: lever locked on the ground. Horn: thrust lever near idle, gear not down and locked. Emergency: free fall, or nitrogen through shuttle valves.
Chapter 23 · Revision and Exam Practice
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The landing gear block is about how the leg works and how the crew know where it is. In the oleo strut the nitrogen carries the weight like a spring, and the oil forced through the orifice damps the motion both ways, on compression and on rebound. The nose wheel must be centred before it retracts, because the bay has little room. Shimmy is a rapid oscillation about the vertical axis, made worse by worn torque links and cured by a shimmy damper. The downlock is an over-centre strut; the uplock is a spring-applied hook released hydraulically. The lights: green means down and locked, red means in transit or disagreeing with the lever, and no lights means up and locked. On the ground the squat switch locks the lever. For emergency extension, the uplocks are released and the gear falls by gravity, or stored nitrogen is used through shuttle valves. After a slush take-off, cycle the gear up, down and up.
Wheels and tyres
Aquaplaning speed and the tyre numbers 0 50 100 150 200 250 300 0 25 50 75 100 125 150 Tyre pressure P (psi) Minimum aquaplaning speed (kt) 135 kt 110 kt 94 kt rotating: 9 √P touchdown, not rotating: 7.7 √P 225 psi: √225 = 15, × 9 = 135 kt Tyre numbers Fusible plugs melt on temperature red 155 °C · green 177 °C · amber 199 °C Rated pressure: cold and unloaded on the aircraft +4 % · hot up to a further +10 % Example: rated 200 psi → 208 psi on the aircraft → about 229 psi hot Nitrogen, at most 5 % oxygen about 90 % of tyre failures: wrong pressure Creep limit 1 in (tyres up to 24 in) · 1½ in above Ply rating = a strength index not the number of plies (32 PR: 18 plies) Wear crown: over-inflated · shoulders: under-inflated Taxi at no more than 25 mph tight turns scrub; speed rating limits VR VP = 9 √P knots with P in psi (rotating tyre) · about 7.7 √P at touchdown · 34 √P with P in kg/cm² · slush: use P ÷ SG.
Chapter 23 · Revision and Exam Practice
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Tyres give the exam its favourite calculation. The dynamic aquaplaning speed is nine times the square root of the tyre pressure, with the pressure in psi and the answer in knots. A tyre at two hundred and twenty-five psi: the root is fifteen, times nine, one hundred and thirty-five knots. That is for a rotating tyre on the take-off run. A tyre that is not yet turning, at touchdown, aquaplanes at a lower speed, about seven point seven times root P, so a one hundred and fifty psi tyre gives about one hundred and ten knots on take-off but only ninety-four at touchdown. The panel on the right gathers the other tyre numbers. Fusible plugs melt at a temperature, not a pressure. Rated pressure is for a cold, unloaded tyre: add four per cent on the aircraft and up to ten per cent more when hot. Creep is normal on new tyres, with a limit of one inch, or one and a half on bigger tyres.
Brakes
Brakes, anti-skid, autobrake and hot wheels Energy ½mV²: double the speed, four times the heat Rotors keyed to the wheel , stators to the torque tube; carbon is lighter and best when hot Fade = too hot to absorb more · drag = not releasing (adjuster, air in the system)Anti-skid senses wheel deceleration ; friction peaks at 10–20 % slip ; it only reduces pressure Autobrake: normal brakes only ; RTO gives full pressure when thrust levers close above 85 kt Hot brakes: dry powder , approach from front or rear , no parking brake; plugs deflate the tyre Friction against wheel slip 0 20 40 60 80 100 0.0 0.5 1.0 Wheel slip (%) Braking friction (relative) peak at 10–20 % slip locked wheel: little braking, no steering Brake energy zones (example chart) none normal caution danger 0 5 17 29 35 23 units Cooling: 5 min per unit above 5 → (23 − 5) × 5 = 90 min Caution: no parking brake, keep clear of the wheels Danger: fire services, fusible plugs will deflate the tyres Fire: dry powder; approach from the front or rear
Chapter 23 · Revision and Exam Practice
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Brakes turn kinetic energy into heat, and kinetic energy goes with the square of speed, so double the speed means four times the heat. In a multi-disc brake the rotors are keyed to the wheel and turn with it, while the stators are keyed to the torque tube. Carbon brakes are lighter and work best when hot. Fade means the brake is too hot to absorb more energy; drag means it does not release fully. Anti-skid compares each wheel’s deceleration with a datum. The best friction comes with about ten to twenty per cent slip; a locked wheel brakes badly and gives no steering, so the system only ever reduces pressure to the wheel that is starting to skid. Autobrake works on the normal brakes only, and in the rejected take-off mode it applies full pressure if the thrust levers are closed above eighty-five knots. The chart gives brake energy zones: twenty-three units means ninety minutes of cooling. Hot wheels: dry powder, and approach from the front or rear.
Flight controls
Which way does it move, and why Topic Rule to remember Sense Column back: elevator up · wheel right: right aileron up · right pedal: rudder right , nose right Adverse yaw The down aileron makes more induced drag: nose yaws away from the roll. Cures: differential, Frise, spoilers, coupling Tabs Balance: opposite , lighter · anti-balance: same way , heavier · servo: pilot moves the tab only · spring: helps at high speed Trim and balance Trim tab moves opposite the surface, irreversible once set · mass balance ahead of the hinge stops flutter Rigging Hot day: cable tension higher (aluminium grows about twice as much as steel) · in safety: pin test, at most 3 threads Stops and checks Primary stop at the surface , secondary at the column · any disturbance: duplicate inspection High lift Leading edge devices out first, in last · flap load relief retracts flap at overspeed, the lever does not move Spoilers Roll: up on the wing with the up aileron · speed brakes cleared to VMO · ground spoilers armed, deploy on spin-up
Warnings: take-off configuration warning is an intermittent horn (trim, flaps, slats, speed brake, doors); the steady horn is the landing gear warning.
Chapter 23 · Revision and Exam Practice
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flight control questions are about which way things move. Pull the column back and the elevator goes up. Turn the wheel right and the right aileron goes up. Push the right pedal and the rudder moves right, so the nose yaws right. Adverse yaw comes from the extra induced drag of the down-going aileron, which yaws the nose away from the turn. For tabs, remember the direction: a balance tab moves opposite to the surface and lightens the controls; an anti-balance tab moves the same way and makes them heavier; with a servo tab the pilot moves only the tab; a spring tab gives most help at high speed. Mass balance sits ahead of the hinge. Rigging: on a hot day the aluminium airframe grows more than the steel cables, so tension rises. The primary stop is at the surface, and any disturbance needs a duplicate inspection. Leading edge devices go out first and in last. Roll spoilers rise on the wing whose aileron goes up.
Powered controls
Feel, follow-up and fly-by-wire Power-assisted: pilot feels part of the load, reversible , no feel unit needed Fully powered: irreversible , so it needs artificial feel and duplication PFCU: servo valve and follow-up ; ports covered → hydraulic lock holds the surface Failed system: its pressure drop opens a spring-loaded bypass , the dead unit follows Q feel: pitot − static = ½ρV²; spring box: deflection only; feel trim resets the datum A320: 2 ELAC, 3 SEC, 2 FAC; last resort: rudder and trim wheel mechanical back-up Power-assisted or fully powered? Power-assisted · pilot feels part of the load · reversible · natural feel, no feel unit · manual reversion: heavy Fully powered · jack does all the work · irreversible · needs artificial feel · needs duplication Fly-by-wire degradation (A320 family) Normal law load factor demand, full protections Alternate law after some failures: most protections lost Direct law stick = surface, manual trim, no protections Mechanical back-up rudder pedals and trim wheel only Protections in normal law: +2.5 / −1 g clean, pitch +30° / −15°, bank 67°, high α, high speed
Chapter 23 · Revision and Exam Practice
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Powered controls come in two kinds. Power-assisted controls share the load with the pilot, who still feels part of it, so they are reversible and need no feel unit. Fully powered controls do all the work, so no air load reaches the pilot: they are irreversible, and they need artificial feel and duplication. In the powered flying control unit the pilot moves a servo valve, the actuator moves, and the follow-up closes the valve when the surface reaches the selected position, trapping fluid in a hydraulic lock. If one hydraulic system fails, its pressure drop lets a spring open a bypass, so the dead unit simply follows the live one. A Q feel unit senses pitot minus static pressure, which is the dynamic pressure, so feel grows with speed squared. On the fly-by-wire airliner the computers fall back from normal law with its protections, to alternate, to direct, and finally to a mechanical back-up of rudder and trim wheel.
Pneumatics
Bleed air: two taps, valves and protection Normal flight: LP stage . HP valve opens at low rpm (idle, descent), closes as LP pressure becomes enough HP valve opens slowly, closes quickly ; a non-return valve stops HP air entering the LP stage Bleed valve: engine/manifold separation; precooler cooled by fan air ; about 40–50 psi, 200 °C Over pressure: relief valve, then HP valve forced shut · overheat: bleed valve closes Isolation (crossbleed) valves normally closed ; opened to feed the other side or for a crossbleed start Compression heats air: T₂ = T₁ × PR0.286 ; bleed costs thrust and raises EGT Pressure from each compressor tap 50 60 70 80 90 100 0 20 40 60 80 100 Engine speed (% rpm) Tap pressure (psi) HP stage LP stage pressure needed HP valve open HP valve closed: LP feeds about 70 % Why compressed air is hot T₂ = T₁ × (pressure ratio)0.286 , in kelvin Pressure ratio 3: −44 °C → +41 °C A take-off HP stage can deliver air above 400 °C, so every source feeds a cooling pack before the cabin
Chapter 23 · Revision and Exam Practice
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bleed air is taken from two compressor stages. The chart shows why. At low engine speed the low pressure stage cannot supply enough, so the high pressure valve opens and the high stage feeds the duct. As the engine speeds up, here at about seventy per cent, the low pressure stage alone is enough and the high pressure valve closes. So in normal climb and cruise the air comes from the low pressure stage. The high pressure valve opens slowly to avoid a surge and closes quickly, and a non-return valve stops high pressure air flowing back into the low stage. The bleed valve, switched by the crew, separates the engine from the manifold, and the precooler uses fan air. An overheat closes the bleed valve. The isolation valves are normally closed. Finally, compressing air heats it: at a pressure ratio of three, air at minus forty-four degrees comes out at about plus forty-one, which is why every source feeds a cooling pack.
Air conditioning
The bootstrap pack, station by station Bleed air +200 °C Primary HX +64 °C Compressor +108 °C Secondary HX +46 °C Turbine −8 °C Water separator > 0 °C common shaft: the turbine drives the compressor -20 20 60 100 140 180 220 Air temperature (°C) Bleed air 200 Primary HX 64 Compressor 108 Secondary HX 46 Turbine −8 Water separator Numbers and order Fresh air 1 lb per seat per min; 0.5 after a failure Cabin 18 to 24 °C · about 30 % relative humidity Carbon monoxide no more than 1 part in 20 000 Heat exchanger at least 80 %, never below ambient Ram air doors closed for take-off and landing Gasper air tapped before the trim air is added Vapour cycle order compressor → condenser → receiver-dryer → expansion valve → evaporator (absorbs heat) The compressor raises the pressure so the turbine has a bigger drop and cools more; the turbine drives the compressor. The water separator sits after the turbine .
Chapter 23 · Revision and Exam Practice
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the air cycle pack with numbers on it, for a hot day. Bleed air arrives at about two hundred degrees. The primary heat exchanger, cooled by ram air, brings it to about sixty-four. The compressor of the cold air unit then raises the pressure, and with it the temperature, to about one hundred and eight. The secondary heat exchanger takes that down to about forty-six. Now the turbine expands the air and takes work out of it, and the temperature plunges to below zero. The turbine is on the same shaft as the compressor, so it drives it: that is the bootstrap. The water separator comes after the turbine, with an anti-ice valve to stop it freezing. Why compress first? Because a heat exchanger can never cool below the ram air temperature, and a bigger pressure drop through the turbine gives more cooling. On the right are the requirement numbers, and the order of the vapour cycle loop.
Pressurisation
Differential pressure and the valves that limit it 0 10000 20000 30000 40000 0 3 6 9 12 15 Aircraft altitude (ft) Pressure (psi) 6.6 7.8 8.3 outside: 14.7 psi at sea level cabin held at 8000 ft = 10.9 psi 2.6 psi differential Differential (psi) -1 0 2 4 6 8 safety valve: max + 0.25 max diff (example 8.6) outflow valve in charge 0.1: pre-pressurise, land inward relief: −0.5 to −1 Cabin altitude (ft) 8000: normal max 10 000: warning, crew O₂ ≈13 000: valves shut (some) 14 000: masks drop cabin rates: climb 500, descent 300 ft/min Constant inflow, variable outflow: differential rising → outflow valve closing ; steady → valve still; falling → valve opening .
Chapter 23 · Revision and Exam Practice
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The graph on the left is computed from the standard atmosphere. Outside pressure falls from fourteen point seven psi at sea level to about two point six at forty-one thousand feet. A cabin held at eight thousand feet is at about ten point nine psi. The difference is the differential: about six and a half psi at thirty thousand feet and about eight point three at forty-one thousand. So the higher you fly with the same cabin altitude, the bigger the differential, and the maximum differential, a structural limit of about eight to nine psi, sets the ceiling. The middle scale shows who acts when. The outflow valve controls everything up to the maximum differential. If it fails shut, the safety valve lifts at about a quarter of a psi above maximum. Below zero, at about minus half to minus one psi, the inward relief valve opens. On the right, the cabin altitudes: eight thousand normal, ten thousand warning, fourteen thousand masks drop.
Pressurisation
Phases, failures and what the gauges show Situation Outflow valve Differential Cabin altitude Climb Closing Increasing Climbs, about 300–500 ft/min Cruise (isobaric) Steady, partly open Constant Constant Descent Opening Decreasing Descends, about 300 ft/min Outflow valve fails open Open Falls Climbs Outflow valve fails shut Shut Rises to max diff + 0.25 psi: safety valve lifts Descends, then held Rapid decompression — Falls to zero in seconds Jumps up: mist, masks, emergency descent Dive below cabin altitude — Negative: inward relief opens — Ditching / dump Ditching closes it Dump: to zero, manually —
Rule of thumb: cabin pressure and differential move together, cabin altitude moves the other way. Rates: cabin climb 500 ft/min, descent 300 ft/min (ears).
Chapter 23 · Revision and Exam Practice
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table turns pressurisation into simple logic, because the inflow is constant. In the climb the outflow valve is closing and the differential is increasing. In the cruise the valve is steady, partly open, and the differential is constant. In the descent the valve is opening and the differential decreasing. If the valve fails open, the differential falls and the cabin climbs. If it fails shut, the differential rises until the safety valve lifts at about a quarter of a psi above the maximum, so the outflow valve acts first and the safety valve after it. A rapid decompression brings a bang, mist in the cabin and a very high cabin rate of climb: masks on and an emergency descent. Diving below the cabin altitude makes the differential negative, and the inward relief valve opens. The ditching control closes the outflow valves; the dump valve takes the differential to zero. Remember the normal cabin rates: five hundred feet per minute up, three hundred down.
Ice and rain protection
Anti-icing, de-icing and detection Anti-icing prevents ice (hot air in wings and intakes, screens); de-icing removes it (boots, prop heaters) Boots: one cycle 34 s ; dwell 206 s light, 26 s heavy; vacuum holds them flat when off Engine anti-ice: IOAT +10 °C or below with visible moisture; it costs thrust and raises EGT Vibrating probe: ice adds mass, frequency falls ; inferential detector senses conditions , not ice Heated windscreen: no ice, no mist and better bird-strike strength; no rain repellent on a dry screen Prop heaters only with the props turning ; frost raising VS 10 % puts lift-off at the stall Boot cycle: 34 s cycle, dwell set by the crew 0 s 60 s 120 s 180 s 240 s 300 s Light icing dwell 206 s Heavy icing dwell 26 s blue: inboard wings · teal: outboard wings · purple: tail (left and right together) Anti-icing or de-icing? Anti-icing: prevents · hot bleed air: jet wings, slats · engine intakes (lip, IGVs) · windscreens and probes (electric) · not Krueger flaps De-icing: removes · pneumatic boots (turboprops) · propeller heaters, cyclic timer · intermittent heater mats · fluid can do either Engine anti-ice: IOAT +10 °C or below with visible moisture
Chapter 23 · Revision and Exam Practice
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Start with the two words. Anti-icing prevents ice from forming: hot bleed air in the wing leading edges and engine intakes, and electrically heated windscreens and probes. De-icing lets ice form and then removes it: pneumatic boots and propeller heaters. Pneumatic boots run a fixed cycle of thirty-four seconds through three groups, inboard, outboard and tail, left and right together. What the crew choose is the dwell: two hundred and six seconds for light icing, so the boots work every four minutes, and twenty-six seconds for heavy icing, once a minute. Engine anti-ice goes on at an indicated outside air temperature of plus ten or below with visible moisture. In the vibrating probe detector, ice adds mass and lowers the resonant frequency. A heated windscreen also has better bird-strike strength. Never use rain repellent or wipers on a dry screen. And frost is no small matter: raise the stall speed by ten per cent and the aircraft is at the stall as it lifts off.
Ground de-icing
Fluids, holdover and the numbers Item Number or rule Clean aircraft No frost, ice or snow on wings, tail, controls, props or intakes; the commander decides Type I Unthickened, about 80 % glycol, usually hot, for de-icing ; short holdover; often dyed orange Type II and IV Thickened: thick at rest, shear off on the take-off run; Type IV (green) gives the longest holdover Holdover starts One-step: start of the treatment · two-step: start of step 2 Hot fluid spray About 70 °C and 100 psi, nozzle close · neat thickened fluid heated to 60 °C max (overheating makes it gel) Hot water step 1 Water at most 95 °C ; not below OAT −7 °C ; step 2 within 3 min Shorter holdover Heavier precipitation, wind or jet blast, a cold-soaked wing, a skin colder than the air, diluted or heated fluid Freezing conditions OAT below +3 °C with visible moisture · cold-soaked wing: clear ice even above 0 °C
Never spray a fresh anti-icing coat over a contaminated one; never spray the windscreens or straight at probes; close engine and APU bleeds when de-icing with them running.
Chapter 23 · Revision and Exam Practice
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ground de-icing is a page of numbers. The principle comes first: the clean aircraft concept, no frost, ice or snow on critical surfaces at take-off, and the commander makes the final decision. Type one fluid is thin, high in glycol, applied hot, and removes deposits, but protects only briefly. Types two and four are thickened: they stay put at rest and shear off during the take-off run, and type four gives the longest holdover time. The holdover time starts at the beginning of the treatment in a one-step process, and at the beginning of the second step in a two-step process. Hot fluid is sprayed at about seventy degrees and a hundred psi. Neat thickened fluid may be heated to sixty degrees at most. Hot water for step one: no hotter than ninety-five degrees, not below minus seven outside, and step two within three minutes. Holdover is shortened by heavier precipitation, wind and a cold-soaked wing.
Emergency equipment
Exits, lighting and slides by the numbers Item Number or rule Megaphones More than 60 seats: 61–99 seats 1 , 100 or more 2 (per deck); PA microphone at each floor-level exit Emergency lighting More than 9 seats: own supply · 20 or more: floor path marking · lasts at least 10 min Lighting switch Flight deck OFF – ARMED – ON, guarded at ARMED; the cabin ON switch overrides Torches At each crew station and floor-level exit; a flashing red light shows the battery is good Exits Outlined by a 5 cm band; sill above 1.83 m (6 ft) needs a descent aid; plug hatches open inwards Slides Armed = girt bar in the floor fittings ; opening from outside disarms; CO₂ + N₂ bottle and aspirators Evacuation More than 44 seats: everyone out in 90 s through half the exits , in darkness Cut-in areas Red or yellow corners outlined in white; extra marks so that no gap exceeds 2 m
Chapter 23 · Revision and Exam Practice
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Emergency equipment questions are mostly numbers tied to seating capacity, so learn this table as a list. Megaphones are needed above sixty seats: one from sixty-one to ninety-nine seats, two from one hundred, per deck. Emergency lighting with its own supply is needed above nine seats, floor path marking from twenty seats, and the lights must last at least ten minutes. The flight deck switch is guarded at armed, and the cabin crew switch overrides it. Torches sit at each crew station and floor-level exit, and a flashing red light means the battery is fine. Exits are outlined with a five centimetre band, and a sill more than one point eight three metres, six feet, above the ground needs a descent aid. A slide is armed when its girt bar is fixed to the floor, so opening the door pulls it out; opening from outside disarms it. Larger types must be evacuated in ninety seconds through half the exits. Cut-in markings have no gap over two metres.
Survival equipment
Life jackets, rafts, beacons and kits Life jackets beyond 50 nm from shore, or over water on take-off and landing; inflate outside the aircraft Rafts: able to fly on one engine → 120 min or 400 nm , whichever is less; others 30 min or 100 nm Raft capacity for all on board even if the largest raft is lost ; CO₂ inflates it, hand pump tops up Survival beacon 121.5 / 243 MHz , 48 h, about 80 nm · ELT 121.5 + 406 MHz ; two ELT(S) with rafts First aid kits 1 / 2 / 3 / 4 for 0–99 / 100–199 / 200–299 / 300+ seats; medical kit above 30 seats and 60 min from help Crash axe or crowbar on the flight deck (over 5700 kg or 9 seats); a second above 200 seats Raft distance limit against cruise speed 100 150 200 250 300 0 100 200 300 400 Normal cruising speed (kt) Distance from land (nm) 120 min 400 nm cap others: 30 min / 100 nm A B Worked (twin able to fly on one engine) A: 180 kt → limit 2 h × 180 = 360 nm; route 340 nm: jackets only B: 240 kt → 480 nm, capped at 400 nm; route 420 nm: rafts 60 people: three 30-seat rafts, so losing the largest still leaves 60 places (two would not be enough) Life jackets: beyond 50 nm from shore
Chapter 23 · Revision and Exam Practice
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
After the evacuation comes survival. Life jackets are carried beyond fifty nautical miles from the shore, or for take-off and landing over water, and are inflated only outside the aircraft. Life rafts depend on a distance rule, and the chart works it out. An aircraft that can continue with an engine out needs rafts beyond one hundred and twenty minutes at cruising speed or four hundred nautical miles, whichever is less; other aircraft, thirty minutes or one hundred nautical miles. So a twin cruising at one hundred and eighty knots has a limit of three hundred and sixty miles; at two hundred and forty knots the four hundred mile cap applies. There must be room for everyone even if the largest raft is lost. The survival beacon transmits on one two one point five and two four three megahertz for forty-eight hours. Emergency locator transmitters use one two one point five and four oh six. And the first aid kits go one per hundred seats, up to four.
Oxygen
The altitudes, the rules and the two systems Altitude (ft) 0k 5k 10k 15k 20k 25k 30k 35k 40k 45k cabin normal max cabin warning · crew oxygen unpressurised: all passengers masks drop · 30 % of pax 100 % of passengers quick-donning crew masks 100 % O₂ from the diluter (32–34k) 100 % O₂ = air at 10 000 ft Time of useful consciousness 10 s 30 s 1 min 3 min 10 min 30 min 18k ft about 30 min 25k ft 3–5 min 30k ft 90–45 s 35k ft 45–30 s 40k ft about 20 s 45k ft about 12 s Crew · gaseous, about 1800 psi; bursting disc → green disc · diluter-demand: NORMAL, 100 %, EMERGENCY · 100 % for smoke; EMERGENCY = overpressure · quick-donning masks above 25 000 ft Passengers · masks drop at 14 000 ft; pull a mask to start flow · chemical generator: NaClO₃ + iron · about 15 min, cannot be stopped, very hot · masks: seats fitted + 10 % (180 seats → 198) Portable and PBE · 120 L: 60 min at 2 L/min, 30 min at 4 L/min · first-aid O₂ for 2 % of passengers · smoke hood / PBE: at least 15 min · no oil or grease near oxygen Pressurised: 100 % of passengers above 15 000 ft (at least 10 min), 30 % from 14 000 to 15 000 ft, 10 % from 10 000 to 14 000 ft after 30 min. Masks = seats + 10 %.
Chapter 23 · Revision and Exam Practice
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Oxygen is a page of altitudes. The percentage of oxygen in the air stays at about twenty-one per cent; what falls is its partial pressure. Ten thousand feet is the highest altitude without oxygen at which performance is not seriously impaired, and the cabin altitude warning sounds there. Passenger masks drop at fourteen thousand feet. In a pressurised aeroplane all passengers need oxygen above fifteen thousand feet, thirty per cent between fourteen and fifteen thousand, and ten per cent between ten and fourteen thousand after thirty minutes. The middle chart shows the time of useful consciousness: about three to five minutes at twenty-five thousand feet, under a minute and a half at thirty thousand, about twenty seconds at forty thousand. The crew use gaseous oxygen through diluter-demand regulators, which give a hundred per cent at about thirty-two to thirty-four thousand feet. Passengers usually have chemical generators: about fifteen minutes, and they cannot be switched off.
Fire detection
Detectors, loops, warnings and the drill Item Rule to remember Spot detectors Melting link: permanent warning, no reset · differential expansion: resets, about 2 s delay against vibration Resistive fire wire Resistance falls with heat; a short circuit gives a false fire warning Capacitive fire wire Capacitance rises with heat; a short circuit gives no false warning Gas-filled detector Heat releases gas, pressure switch closes; a broken tube gives LOOP FAULT , never fire Double loop A AND B must agree; one failed loop: FAULT and single-loop operation Warning and test Bell plus steady red handle light; overheat is amber , no bell; the test proves continuity Smoke detectors Optical (light scatter) or ionisation (ion current falls); in holds, avionics bays and lavatories Engine fire drill Thrust lever close, HP cock off, pull the handle (isolates, arms squibs), discharge; 30 s, second bottle
Chapter 23 · Revision and Exam Practice
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fire detection questions test how each detector responds, and how it fails. A melting link gives a permanent warning, so you cannot tell when the fire is out; a differential expansion detector resets and has a short delay against vibration. The fire wires are the favourite. In a resistive wire the core resistance falls with heat, so a short circuit looks like a fire and gives a false warning. In a capacitive wire the capacitance rises with heat, and a short circuit stores no charge, so no false warning. A gas-filled detector works on a pressure rise; if its tube breaks, you get a loop fault, never a fire warning. Engine loops are doubled and both must agree. A fire warning is a bell with a steady red light in the handle; an overheat is amber only. Smoke detectors are optical or ionisation types, in holds, avionics bays and lavatories. And the drill: shut the engine down, pull the handle, then discharge, with the second bottle after about thirty seconds.
Fire protection
Agents, bottles and how many extinguishers Halon 1211 (BCF) : hand-held, cabin and flight deck · Halon 1301 : fixed, engines, APU, cargoWater: class A only · foam: fuel spills · dry powder: wheels and brakes · sand: metal fires Hand-held: 7–30 seats 1 , 31–60 2 , 61–200 3 , then +1 per 100 seats to 8 ; plus 1 on the flight deck From 31 seats at least 1 BCF , from 61 seats at least 2 Lavatory waste bin: automatic halon bottle with a fusible seal, 20 seats or more Overheated bottle vents overboard: green disc out, red disc shows · fired: DISCH light, pin Hand-held extinguishers in the cabin 0 100 200 300 400 500 600 700 0 2 4 6 8 Passenger seats Extinguishers 1 2 3 4 5 6 7 8 total in the cabin of which BCF (minimum) Worked: add 1 BCF on the flight deck 25 seats cabin 1 + flight deck 1 = 2 70 seats cabin 3 (BCF ≥ 2) + flight deck 1 = 4 186 seats cabin 3 (BCF ≥ 2) + flight deck 1 = 4 520 seats cabin 7 (BCF ≥ 2) + flight deck 1 = 8
Chapter 23 · Revision and Exam Practice
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fire protection has three things to learn: the agents, the bottles and the counts. Halon twelve eleven, called B C F, is the hand-held agent for the cabin and flight deck. Halon thirteen oh one is in the fixed bottles for the engines, the APU and the cargo holds. Water is for class A fires of paper and fabric only, foam for fuel spills, dry powder for wheels and brakes because it does not cool them suddenly, and sand for metal fires. The chart gives the hand-held count by passenger seats: one up to thirty, two up to sixty, three up to two hundred, then one more per hundred seats up to eight, and always one more on the flight deck. From sixty-one seats at least two must be B C F. Lavatory waste bins have an automatic bottle from twenty seats. And an overheated bottle vents overboard, blowing out the green disc so that a red disc shows.
Aviation fuels
Grades, colours and contamination Fuel or topic Facts to remember AVGAS 100LL 100/130, blue , low lead: the common piston grade · AVGAS 100: same rating, green · AVGAS 80: red Jet A-1 Kerosene, SG about 0.80 , flash point 38 °C minimum, freezes at −47 °C , undyed: clear to straw Jet A Kerosene, freezes at −40 °C , used mainly in the USA Jet B (wide-cut) Gasoline + kerosene, SG 0.77 , low flash point, volatile: passengers off when it is loaded Labels Turbine fuel: white on black · AVGAS: white on red , with the grade Cloudy sample Air rises: clears bottom up · water sinks: clears top down · in the exam: usually water FSII and microbes FSII stops free water freezing and is a biocide · fungus lives at the fuel/water interface, its acid attacks sealant SG and mass SG falls as fuel warms; load by mass : kg = litres × SG · a cold-soaked climb releases dissolved water as ice
Chapter 23 · Revision and Exam Practice
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel grades are easy marks if you keep the colours straight. AVGAS one hundred L L is blue, with a rating of one hundred over one hundred and thirty. AVGAS one hundred has the same rating but is green, with more lead. AVGAS eighty is red. Turbine fuels are not dyed. Jet A one is kerosene with a specific gravity of about point eight and a freezing point of minus forty-seven degrees; Jet A freezes at minus forty and is used mainly in the United States. Jet B is wide-cut, a mix of gasoline and kerosene, with a specific gravity of point seven seven and a low flash point; passengers must disembark if it is loaded. Turbine fuel equipment is labelled white on black, AVGAS white on red. A cloudy sample that clears from the top down is water. The icing inhibitor also kills fungus. And specific gravity falls as fuel warms, so always load by mass.
Fuel systems
Tanks, pumps, gauging and refuelling Integral tanks; baffle check valves let fuel flow inboard only; 2 % expansion space, vent surge tank Boosters: centrifugal, AC, 20–40 psi , in a collector box; they prevent vapour lock and pump cavitation Centre tank first , wings last; cross-feed: any tank to any engine, not for fire isolation Capacitance gauging measures mass ; power failure → slowly to empty ; water → full scale high Jettison stops at the preselected figure; keep enough for 10 000 ft + 45 min Fuelling zone 6 m ; bond first , unbond last; radar 30 m ; no AVGAS or Jet B with passengers aboard Twin-jet feed and cross-feed No. 1 tank left wing Centre tank used first No. 2 tank right wing AC boosters: 20–40 psi centre pumps cross-feed valve: normally shut LP valve (fire handle) Engine 1 LP valve (fire handle) Engine 2 Worked: correcting an imbalance Left 5200 kg, right 4000 kg; each engine burns 1200 kg/h 1 · open the cross-feed 2 · right pumps off: left tank feeds both at 2400 kg/h 3 · left falls 2400 kg/h faster than right: (5200 − 4000) ÷ 2400 = 30 minutes; then pumps on, cross-feed shut Gauge: power failure → empty · water → full scale high Jettison: keep enough for 10 000 ft + 45 min
Chapter 23 · Revision and Exam Practice
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fuel system page. Airliners use integral tanks, with baffle ribs whose check valves let fuel flow inboard towards the pumps but not outboard, and a two per cent expansion space. Booster pumps are centrifugal, driven by AC motors, delivering twenty to forty psi from a collector box that always holds fuel. They push fuel to the engine, preventing vapour lock and cavitation of the engine pump. The centre tank is used first and the wing tanks last, for bending relief. The cross-feed valve connects any tank to any engine. The worked example corrects an imbalance: with twelve hundred kilograms more on the left, open the cross-feed and switch off the right pumps, and the left tank feeds both engines at two thousand four hundred kilograms an hour, so it takes thirty minutes. Capacitance gauges measure mass; on power failure they drift to empty, and water makes them read full scale high. Refuelling: a six metre zone, bond first, and no AVGAS or wide-cut fuel with passengers on board.
Classic traps
Where marks are lost Accumulator gauge Reads system pressure when charged. You see the pre-charge only with the system depressurised .
Fuses and shuttles A fuse closes , it does not rupture. A shuttle moves only when the alternate is pressurised.
Aquaplaning units 9 √P needs P in psi . Touchdown (7.7 √P) is lower . Slush: P ÷ SG first.
Anti-skid and autobrake Anti-skid only reduces pressure. RTO autobrake only above 85 kt ; normal brakes only.
Outflow and safety valve Differential rising = valve closing . Safety valve at max diff + 0.25 psi, after the outflow valve.
Fire wires Resistive short = false fire . Capacitive short = no false fire. Gas tube broken = fault .
Raft rule The lesser of 120 min and 400 nm (others 30 min, 100 nm), at normal cruise speed.
Fuel gauge Capacitance: power failure → empty ; water in the tank → full scale high .
Chapter 23 · Revision and Exam Practice
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
These are the places where marks are lost. The accumulator gauge reads system pressure once fluid is in; the pre-charge shows only with the system depressurised. A hydraulic fuse closes, it never ruptures, and a shuttle valve moves only when the alternate supply is pressurised. The aquaplaning formula needs the pressure in psi, the touchdown figure is lower, and for slush you divide by the specific gravity first. Anti-skid only ever reduces brake pressure, and the rejected take-off autobrake works only above eighty-five knots. A rising differential means the outflow valve is closing, and the safety valve acts after it, at a quarter of a psi above the maximum. A short in a resistive fire wire gives a false fire warning; in a capacitive wire it does not; a broken gas tube gives a fault. The raft rule is the lesser of the time and the distance. And a capacitance gauge goes to empty on power failure but full scale high with water.
Method and summary
How to answer, and your last-minute list 1 · Read the stem Underline NOT, EXCEPT, first, normally, most likely. Many wrong answers are true statements about the wrong case.
2 · Name the job Ask what the component is for. A valve that “limits”, “maintains” or “isolates” tells you its name.
3 · Fail which way? For any failure, ask which way the valve, gauge or warning goes: open, shut, empty, full scale, fault or fire.
4 · Check the units psi or bar, kt or mph, ft or m, litres or kg. Write the formula, then check the size of the answer.
Pressures Hydraulics 3000 psi · boosters 20–40 psi · oxygen 1800 psi · max diff 8–9 psi · safety + 0.25 psi.
Speeds and times VP = 9√P · RTO 85 kt · boots 34 s · 10 min lights · 90 s evacuation · 15 min generator.
Altitudes Cabin 8000 · warning 10 000 · masks 14 000 · all pax 15 000 · quick-don 25 000 · 100 % O₂ 32–34 000 ft.
Counts Extinguishers 1/2/3 to 8 + flight deck · megaphones 1/2 · first aid 1 per 100 · masks seats + 10 %.
Chapter 23 · Revision and Exam Practice
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Finish with a method, then the list. First, read the stem: underline words like not, except, first and normally, because many wrong options are true statements about a different case. Second, name the job of the component: a valve that maintains pressure, limits it or isolates a line tells you its own name. Third, for any failure, ask which way it goes: open or shut, empty or full scale, fault or fire. Fourth, check the units, psi or bar, knots or miles per hour, litres or kilograms, and check the size of your answer. Then the last-minute numbers: three thousand psi hydraulics, twenty to forty psi boosters, eighteen hundred psi oxygen, eight to nine psi maximum differential. Aquaplaning nine root P, autobrake eighty-five knots, thirty-four second boot cycle, ten minutes of lighting, ninety seconds to evacuate. Cabin altitudes eight, ten, fourteen and fifteen thousand. Now go to the questions.