Aircraft Systems · Chapter 9
Tabs, High-lift Devices and Spoilers How hinge moments are tamed by balances and tabs, how the aircraft is trimmed, and how flaps, slats, spoilers and speed brakes reshape the wing.
TABS · FLAPS · SLATS · SPOILERS
lighter controls, trimmed flight, slow landings, quick descents
slat
spoiler
slotted flap
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the secondary flight controls. In the last lesson we moved the primary surfaces. Now we make them lighter to move, using hinge balances and tabs, and we look at mass balance, which stops flutter. Then we see how an aircraft is trimmed: trim tabs, the trimming tailplane and Mach trim. After that come the high lift devices, flaps, slats and Krueger flaps, and the systems that drive and protect them. Finally the spoilers, which help the ailerons roll the aircraft, act as speed brakes in flight and dump lift on the runway.
Roadmap
Lighter, trimmed and reshaped 1 · Balance and tabs Hinge moments. Set-back, horn and internal balance. Four kinds of tab. Mass balance.
2 · Trimming Trim tabs, the trimming tailplane, spring bias, CG shift, feel trim, Mach trim.
3 · High lift devices Flap types and drive system, load relief, slats and Krueger flaps, sequencing.
4 · Spoilers Roll spoilers, speed brakes, lift dumpers and automatic deployment.
Chapter 9 · Tabs, High-lift Devices and Spoilers
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First, hinge moments, the reason controls get heavy, and the ways designers lighten them: set-back hinges, horn balances, internal balances, and four kinds of tab, balance, anti-balance, servo and spring. We also cover mass balance, which prevents flutter. Second, trimming: why an aircraft needs it, and the trim tab, the variable incidence tailplane, spring bias, centre of gravity adjustment, feel trim and Mach trim. Third, the high lift devices from a systems point of view: the flap types, how flaps are driven and protected, flap load relief, and the leading edge devices with their sequencing. Fourth, spoilers: roll spoilers, speed brakes and ground spoilers, including the automatic logic that deploys them on landing.
Part 1 · Hinge moments
Why controls get heavy Air force on a deflected surface tries to turn it back about its hinge Hinge moment = force × distance from hinge to the surface's centre of pressure The pilot must hold an equal and opposite moment: the stick force Force ∝ surface size and IAS² : double the IAS, four times the load Big, fast aircraft need help: aerodynamic balance or power
F on the surface
arm
Hinge moment = F × arm (hinge to surface CP)
0
50
100
150
200
250
300
0
400
800
1200
1600
IAS (kt)
hinge moment (N m)
350 N m at 150 kt
1400 at 300 kt
2 m² surface, same deflection: double the IAS, four times the moment
Chapter 9 · Tabs, High-lift Devices and Spoilers
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a control surface is deflected, the air pushes on it, and that force acts at the surface's own centre of pressure, some distance behind the hinge. Force times that distance is the hinge moment, and it tries to turn the surface back towards neutral. To hold the surface where it is, the pilot has to apply an equal and opposite moment through the controls, and that is what you feel as stick force. The hinge moment depends on the angle of attack and on the deflection. Crucially, the force depends on the size of the surface and on the square of the indicated airspeed. In the worked example, a two square metre surface gives about three hundred and fifty newton metres at one hundred and fifty knots, but about fourteen hundred at three hundred knots. On large, fast aircraft the forces would be far too high, so the pilot needs help: aerodynamic balance, or power.
Part 1 · Aerodynamic balance
The set-back (inset) hinge Move the hinge back into the surface , towards its centre of pressure The arm shrinks, so the hinge moment shrinks The force , and so the control effectiveness , is unchanged Too far back, past the CP: overbalance , the surface runs away The CP moves with deflection, so the set-back is limited
Hinge at the surface leading edge
F = 2000 N
hinge
arm 0.15 m
moment 300 N m
Hinge set back 0.10 m
F = 2000 N
hinge
arm 0.05 m
moment 100 N m
Hinge behind the CP: overbalance
F = 2000 N
hinge
arm 0.05 m
moment −100 N m
The force (and the control power) is unchanged; only the arm shrinks.
Chapter 9 · Tabs, High-lift Devices and Spoilers
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aerodynamic balance uses the air forces on the control surface itself to reduce the hinge moment. The simplest form is the set-back, or inset, hinge. Instead of hinging the surface at its leading edge, the hinge is moved back into the surface, closer to its centre of pressure. Look at the numbers. A surface carries two thousand newtons at its centre of pressure, nought point one five metres behind its leading edge. Hinged at the leading edge, the moment is three hundred newton metres. Set the hinge back by nought point one metres and the arm is only nought point nought five, so the moment falls to one hundred. The force on the surface is the same, so the control is just as effective. But do not go too far. If the hinge ends up behind the centre of pressure, the moment reverses and the surface tries to run away, which is called overbalance.
Part 1 · Aerodynamic balance
Horn balance and internal balance
Horn balance
Internal balance
tailplane
hinge line
horn
elevator
Area ahead of the hinge makes an opposing moment.
Unshielded horns also help mass-balance the surface.
vented to upper surface: low p
vented to lower surface: high p
surface down
The balance panel (with a flexible seal) feels the pressure
difference and pushes the surface back towards neutral.
Both put some of the surface pressure ahead of the hinge : smaller hinge moment, no loss of control effectiveness.
Chapter 9 · Tabs, High-lift Devices and Spoilers
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more forms of aerodynamic balance work on the same principle. The horn balance, on the left, is a part of the surface at its tip that extends forward of the hinge line. The air load on the horn produces a hinge moment in the opposite direction to the load on the main surface, so the overall moment, and the stick force, is reduced, without reducing the control effectiveness. The internal balance, on the right, hides the balancing area inside the wing. A panel ahead of the hinge sits in a chamber sealed with a flexible seal and vented to the upper and lower surfaces. When the surface goes down, pressure above the wing falls and pressure below rises. The balance panel feels that pressure difference, and the moment it makes opposes the moment on the main surface. Again the hinge moment drops while effectiveness is kept.
Part 1 · Tabs
The balance tab A small tab at the trailing edge, geared to the fixed structure It moves opposite to the surface whenever the surface moves Its force acts at a long arm and opposes the surface's hinge moment Stick force is reduced Unlike the balances, it gives some loss of control effectiveness
Balance tab: geared to move OPPOSITE
surface force
tab force
link to fixed wing
Surface down: the tab goes up automatically
Tab force acts far behind the hinge, opposite
to the surface force: hinge moment reduced
Price: slightly less control effectiveness,
because the tab force opposes the surface force
Chapter 9 · Tabs, High-lift Devices and Spoilers
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
All the balances so far work by putting some of the pressure ahead of the hinge. The balance tab works differently: it puts a force at the trailing edge. It is a small tab, linked to the fixed structure so that whenever the surface moves, the tab moves the opposite way. Watch the diagram. The surface goes down and makes an upward force. The tab goes up and makes a smaller downward force, but it acts a long way behind the hinge, so its moment opposes the surface's hinge moment and the stick force falls. There is a price. Because the tab force is opposite to the surface force, the total force is a little smaller, so a balance tab gives some reduction in control effectiveness. That is the difference to remember: set-back hinges, horns and internal balances keep effectiveness; the balance tab loses a little.
Part 1 · Tabs
The anti-balance tab Geared to move in the same direction as the surface Adds camber: more control effectiveness Increases the hinge moment: heavier stick forces Used where a control would otherwise be too light Often on stabilators , where it also adds feel
Anti-balance tab: moves the SAME way
surface force
tab force
link to fixed structure
Surface down: the tab goes further down
More camber: more control effectiveness
But a bigger hinge moment: heavier stick force
Used to add feel where a control would be too light,
for example on some all-moving tailplanes
Chapter 9 · Tabs, High-lift Devices and Spoilers
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The anti-balance tab is the opposite idea. It is geared to move in the same direction as the control surface, so when the surface goes down, the tab goes down further. That adds camber at the trailing edge, so the control becomes more effective. But it also increases the hinge moment, so the stick force goes up. Why would anyone want heavier controls? Because some controls, especially all-moving tailplanes, are so well balanced that they would feel too light, and a pilot could easily over-control. The anti-balance tab adds feel and increases the effectiveness at the same time. For the exam, remember: a balance tab moves opposite to the surface and lightens the controls but slightly reduces their effectiveness, while an anti-balance tab moves the same way, increases effectiveness and makes the stick forces heavier.
Part 1 · Tabs
The servo tab The cockpit control moves only the tab ; the surface floats on its hinge Tab force moves the surface until the hinge moments balance The pilot only has to move a small tab: low stick forces Stationary on the ground: column moves the tab only With external locks on the surface the column is still free
Servo tab: the pilot moves only the tab
surface force
tab force
from the cockpit control
Pilot puts the tab UP: the tab force pushes the
free-floating surface DOWN until moments balance
On the ground (no airflow) the column moves
only the tab; with external locks fitted the
column is still free to move
Chapter 9 · Tabs, High-lift Devices and Spoilers
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
With a servo tab, there is no direct connection between the cockpit control and the main surface at all. The pilot's input moves only the tab. The surface itself floats freely on its hinge. In flight, when the pilot raises the tab, the airflow pushes the tab down, and that moment drives the whole surface downward, until the moments about the hinge balance. Because the pilot only has to move a small tab against a small hinge moment, the stick forces are low, which is why servo tabs were used on large aircraft before powered controls. Two consequences follow. On the ground, with no airflow, moving the column moves only the tab. And if external control locks are fitted to the surface, the cockpit control will still move freely, so a full and free check will not reveal the locks. The servo tab can also act as a manual reversion if hydraulic power is lost.
Part 1 · Tabs
The spring tab A balance or servo tab with a spring in the linkage Tab movement is proportional to the stick force Low speed: spring hardly compresses, the control acts directly High speed: large force, spring compresses, tab gives most help Used mainly to reduce control loads at high airspeed
Spring tab: the help grows with the force
0
50
100
150
200
250
300
0
1
2
3
4
IAS (kt)
stick force for a given deflection (× force at 150 kt, plain)
no tab
spring tab
0.8 at 300 kt
Low speed: the spring barely compresses, the tab hardly
moves, and the control feels like a direct one.
High speed: big force, spring compresses, tab helps a lot.
(illustrative model: half the force at 150 kt)
Chapter 9 · Tabs, High-lift Devices and Spoilers
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The spring tab is a clever modification of the balance or servo tab. A spring is put in the linkage, so the amount the tab moves is proportional to the force the pilot is applying. At low speed the control forces are small, the spring hardly compresses, the tab barely moves, and the control behaves almost like a direct one, with natural feel. At high speed the forces are large, the spring compresses, the tab deflects, and it gives the most assistance exactly when the stick forces would be greatest. The graph uses a simple model. Without a tab, the force for a given deflection quadruples from one hundred and fifty to three hundred knots. With this spring tab it is halved at one hundred and fifty knots and is only about point eight at three hundred. With external locks on, the column can move a little, but it feels very stiff.
Part 1 · Quick reference
Balances and tabs at a glance Device Moves Stick force Effectiveness Set-back hinge, horn, internal part of surface ahead of hinge Reduced Unchanged Balance tab opposite to the surfaceReduced Slightly reduced Anti-balance tab same way as the surfaceIncreased Increased Servo tab pilot moves the tab only Low Surface floats; tab drives it Spring tab in proportion to stick force Reduced most at high speed Direct feel at low speed Trim tab opposite to the surface, set by trim Reduced to zero Unchanged
A trim tab, once set, is irreversible : air loads cannot move it.
Chapter 9 · Tabs, High-lift Devices and Spoilers
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is everything on one page. The set-back hinge, the horn balance and the internal balance all put part of the surface ahead of the hinge; they reduce the stick force and keep the effectiveness. The balance tab moves opposite to the surface; it reduces the stick force at a small cost in effectiveness. The anti-balance tab moves the same way as the surface; it increases both the stick force and the effectiveness. With a servo tab, the pilot moves only the tab and the tab flies the free-floating surface, so forces are low. The spring tab moves in proportion to the stick force, so it helps most at high speed and leaves direct feel at low speed. And the trim tab, which we meet next, moves opposite to the surface and is set by the trim control to reduce the holding force to zero. Once set, it cannot be moved by air loads.
Part 1 · Flutter
Mass balance prevents flutter Flutter : an oscillation of a surface coupled with bending and twisting of the structureIf the surface CG is behind the hinge , its inertia makes it swing as the wing flexes The oscillation can become divergent and destroy the structure Cure: a weight ahead of the hinge , bringing the CG to or slightly ahead of it Most control surfaces are mass balanced; re-check after repainting or repair
Mass balance: weight ahead of the hinge
lead weight
hinge
surface CG moved forward
Why: flutter
The wing bends and twists under load. If the surface CG
is behind the hinge, its inertia makes it lag and swing,
feeding the oscillation. It can diverge and break the structure.
divergent flutter
Chapter 9 · Tabs, High-lift Devices and Spoilers
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mass balance has nothing to do with stick force. Its purpose is to prevent flutter. Flutter is an oscillation of a control surface coupled with the bending and twisting of the wing or tail under load. If the centre of gravity of the control surface is behind its hinge, then when the structure flexes, the surface's inertia makes it lag behind and swing about its hinge, and that swinging can feed energy back into the structure. In certain conditions, usually at high speed, the oscillation becomes divergent and can tear the structure apart in seconds. The cure is to add weight ahead of the hinge line, often lead in the nose of the surface or on an arm, bringing the surface's centre of gravity to a point close to or slightly ahead of the hinge, as the designer requires. That is why extra paint or a repair on a control surface means it must be re-balanced.
Part 2 · Trimming
Why we trim An aircraft is trimmed when it holds its attitude and speed with no force on the cockpit controls.
Pitch Changes of speed , of power , and of CG position (fuel burn, passengers, flap).
Yaw Asymmetric power on a multi-engined aircraft; changes of propeller torque .
Roll Less often: an asymmetric configuration or a lateral CG offset (fuel imbalance).
Trim tab Small surface on the control, moved opposite to it by a wheel or switch.
Trimming tailplane Whole stabiliser incidence changed by a screw jack.
Others Spring bias, CG adjustment by fuel transfer, feel unit datum.
Chapter 9 · Tabs, High-lift Devices and Spoilers
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
An aircraft is trimmed when it will hold its attitude and speed without the pilot having to apply any force to the controls. If a surface has to stay deflected to keep the aircraft balanced, the pilot would otherwise have to hold it there, and trimming reduces that force to zero. In pitch, you need to re-trim after changes of speed, changes of power, and changes in the position of the centre of gravity, from fuel burn, passenger movement or flap. In yaw, trimming is needed on a multi-engined aircraft with asymmetric power, and for changes in propeller torque. In roll, trim is needed less often, perhaps for an asymmetric configuration or a lateral offset of the centre of gravity, such as a fuel imbalance. The main methods are the trim tab, the variable incidence tailplane, spring bias, centre of gravity adjustment, and adjustment of the artificial feel unit.
Part 2 · Trimming
The trim tab A small adjustable surface in the trailing edge of a control surface Set from the cockpit by a trim wheel or switch , in the instinctive sense Moves opposite to the surface until its hinge moment balances the surface's Holds the surface deflected with zero stick force Fixed tabs (often on ailerons) are bent on the ground for a permanent out-of-trim
Holding elevator up, then trimming
1. Pilot holds a pull force to keep the elevator up
tab force up
2. Trim wheel back: the tab moves DOWN
until its moment holds the elevator UP with zero stick force
The tab always moves opposite to the surface it trims.
The trim wheel works in the instinctive sense.
Chapter 9 · Tabs, High-lift Devices and Spoilers
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The trim tab is a small adjustable surface set into the trailing edge of a primary control surface. It is moved from the cockpit by a trim wheel or a trim switch, normally arranged to work in the instinctive sense: wind the wheel back for nose up. Watch the scene. Suppose the aircraft needs the elevator held slightly up. Without trim, the pilot must hold a steady pull. Now the pilot winds the trim, and the tab moves the opposite way to the elevator, down, until the upward force on the tab gives a hinge moment that exactly balances the elevator's own hinge moment. The elevator now stays up by itself and the stick force is zero. Some tabs cannot be adjusted in flight. These fixed tabs, often found on ailerons, are bent on the ground to correct a permanent out-of-trim condition, and they work in the same way.
Part 2 · Trimming
The variable incidence tailplane Trim by changing the incidence of the whole tailplane (screw jack) Used with manual and with powered elevators Advantages : less drag when trimmed, and the full elevator range is keptElectric trim switches in pairs (arm + direction), both moved together: guards against trim runaway Set for take-off from the CG: wrong setting gives a tail strike or a very heavy rotation
Variable incidence tailplane (stabiliser trim)
pivot
screw jack
elevator near neutral
Trimmed: less drag (streamlined tail) and the
full elevator range is still available.
Electric trim: two switches (arm + direction) must
be moved together: guards against trim runaway.
Take-off setting from the CG: too nose-up = fast
rotation, tail strike; too nose-down = heavy pull.
Chapter 9 · Tabs, High-lift Devices and Spoilers
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Larger aircraft trim in pitch by changing the incidence of the whole tailplane, usually with a screw jack at its leading edge. It is used with both manual and powered elevators. To trim, the tailplane incidence is changed until the tail produces the balancing load with the elevator free. This has two big advantages. The trimmed tail is streamlined, with the elevator near neutral, so the drag is less. And because the elevator stays near neutral, trimming does not use up any of its travel, so the full range of pitch control remains. The trim may be driven by a wheel or by electric trim switches, which come in pairs: one arms the motor and the other selects the direction, and both must be moved together, which guards against a trim runaway. The take-off setting depends on the centre of gravity, from the flight manual; set wrongly, it can cause a tail strike or a very heavy rotation and a longer take-off.
Part 2 · Trimming
Other ways to trim
adjustable
anchor
spring holds the column: no tab
fuel
CG aft, nearer the CP: less trim drag
to column
datum moved
powered controls: re-centre the feel springs
Spring bias An adjustable spring replaces the pilot's holding force. No tab is needed.
CG adjustment Move the CG towards the CP by transferring fuel fore and aft: less balancing load, less trim drag , more range.
Artificial feel trim Powered controls: move the datum of the feel unit so it no longer pushes the column.
Chapter 9 · Tabs, High-lift Devices and Spoilers
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three more methods. Spring bias uses an adjustable spring in the control circuit to replace the pilot's holding force; no tab is required. Centre of gravity adjustment attacks the problem at its root. If the controls are used to trim, the deflected surfaces add drag. By moving the centre of gravity closer to the centre of pressure, the out-of-balance pitching moment is reduced, so the tail needs a smaller balancing load and creates less trim drag, which increases the cruise range. The centre of gravity is moved by pumping fuel between tanks near the nose and the tail. Finally, on aircraft with fully powered controls, there is no air load on the column, only the artificial feel unit pushing it back towards its datum. To trim, the datum of the feel unit is moved, so that it no longer pushes, and the stick force disappears.
Part 2 · Trimming
Mach trim Near high subsonic speed the wing CP moves aft Result: a strong nose-down pitching moment, "tuck under " Mach trim senses Mach number above a datumA servo moves the stabiliser (or shifts the CG by fuel transfer ) to hold the trim It works whether or not the autopilot is engaged
High subsonic: the wing CP moves aft
CG
lift at M 0.70
at M 0.82: further aft
nose-down "tuck under"
Mach trim
Senses Mach above a datum and, through a servo,
moves the stabiliser nose-up (or shifts the CG aft)
to hold the trimmed attitude.
Works whether or not the autopilot is engaged.
front trim tank
rear trim tank
fuel transfer
Chapter 9 · Tabs, High-lift Devices and Spoilers
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
As an aircraft approaches high subsonic speed, shock waves form on the wing and the centre of pressure moves rearward. With the lift now acting further behind the centre of gravity, there is a large nose-down pitching moment, known as tuck under. Left alone, the nose drops, the speed rises, and the effect gets worse. An automatic correction is therefore essential, and it is called Mach trim. The system senses when the Mach number exceeds a datum value and, through a servo, moves the horizontal stabiliser nose-up as the Mach number increases, or on some aircraft shifts the centre of gravity aft by transferring fuel to a rear trim tank, to hold the trimmed attitude. Note that Mach trim must work whether or not the autopilot, or any other automatic flight control, is engaged. Its purpose is to counter the nose-down tuck.
Part 3 · High lift devices
Trailing edge flaps
Plain (camber) flap
light aircraft; simple
Split flap
lower surface only; high drag
Slotted flap
slot re-energises the flow
Fowler flap
slides aft: area + camber
C L max
+50 %
C L max
+60 %
C L max
+65 %
C L max
+90 %
Drag
moderate
Drag
highest
Drag
lower
Drag
lowest
Pitch change
nose down
Pitch change
nose down
Pitch change
nose down
Pitch change
largest nose down
Light aircraft: usually plain flaps. Jet transports: slotted Fowler flaps plus leading edge devices. All raise both lift and drag .
Chapter 9 · Tabs, High-lift Devices and Spoilers
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
High lift devices raise the lift coefficient so that a large aircraft can make enough lift at low speed for take-off and landing. Smaller aircraft usually have only trailing edge flaps; jet transports have devices on both the leading and trailing edges. Every flap type increases both lift and drag, in varying amounts. The plain, or camber, flap is the most popular on light aircraft: a hinged rear part of the wing that adds camber. The split flap hinges down only the lower surface, giving a lot of drag. The slotted flap opens a slot that lets high pressure air from below re-energise the flow over the flap. The Fowler flap slides back on tracks before turning down, adding both wing area and camber, so it gives the largest increase in maximum lift coefficient. Fowler flaps, often with two or three slots, are used on most large transports, and they give the largest nose-down pitch change. The figures shown are only typical.
Part 3 · High lift devices
How a large aircraft drives its flaps Flap lever signals two slat/flap computers : control, monitoring, test An electrically controlled hydro-mechanical power unit drives torque shafts Shafts turn screw actuators on each flap, so both wings move together Protected against asymmetry , runaway , uncommanded movement and overspeed Torque limiters or brakes stop the drive on excess torque; alternate drive by hydraulics or an electric motor
Flap lever
with gates
Slat/flap computers
× 2: control, monitor
Power unit
hydro-mechanical
screw actuators
screw actuators
torque shafts to both wings
brake
brake
Alternate drive
hydraulic or electric
Protected against: asymmetry, runaway,
uncommanded movement and overspeed.
Torque limiters / brakes stop the drive if
excessive torque is sensed (jam).
Chapter 9 · Tabs, High-lift Devices and Spoilers
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a large aircraft, moving the flap lever does not move the flaps directly. The lever sends an input to two slat and flap computers, which control, monitor and test the system. They command an electrically controlled, hydro-mechanical power unit, which turns a system of torque shafts running out along both wings. The shafts drive screw actuators on each flap panel, and because one shaft system drives both wings, the flaps stay symmetrical. Watch the Fowler flap run aft on its tracks and then down. The computers watch the flap positions and protect against asymmetry, runaway, uncommanded movement and overspeed, and the position is shown on the flight deck display. Torque limiting brakes stop the drive if excessive torque is sensed, for example if a flap jams. If the main system fails, an alternate hydraulic supply or an electric motor drives the same gearbox and shafts.
Part 3 · High lift devices
Flap load relief The load relief system (load limiter) protects flaps from excess airspeed Above a set speed the flaps retract to an intermediate (mid) position Below the limit they re-extend automatically to the selected position The flap lever does not move : watch the position indicator It is a protection, not a reason to fly fast with flap
Flap load relief (flap 40 selected)
140
145
150
155
160
165
170
175
20
25
30
35
40
45
IAS (kt)
flap angle (°)
above 162 kt:
retract to 30
below 157 kt: back to 40
Protects the flaps and their tracks from
overload if the speed is too high for the setting.
Automatic both ways; the lever stays at 40.
(illustrative speeds; each type has its own)
Chapter 9 · Tabs, High-lift Devices and Spoilers
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Flaps and their tracks are designed for the air loads at a limited speed for each setting. If the aircraft flies faster than that with full flap selected, for example in turbulence or during a go-around, the loads could damage them. The flap load relief system, also called a load limiter, protects against this. Above a predetermined airspeed it retracts the flaps to a mid position, and when the speed drops back below its limit, it automatically returns them to the fully extended position. In this illustrative graph, flap forty is selected. As the speed passes one hundred and sixty two knots, the flaps run back to thirty. Below one hundred and fifty seven knots they run out again to forty. The flap lever itself stays at forty throughout, so the crew must watch the flap position indicator to see what is happening.
Part 3 · Leading edge devices
Slats, Krueger and variable camber flaps Krueger flaps : hinge down and forward from the lower surface Variable camber flaps : flexible panels that form a curved noseSlats : leading edge sections that move forward , sealed or slotted Often combined: e.g. Krueger inboard , variable camber outboard Driven by hydraulics or air turbine motors , from the flap lever
Krueger flap
hinges down and forward from the lower surface
Variable camber flap
flexible panel bends into a curved nose
Slat
runs forward on tracks: sealed or slotted
slot
Powered by hydraulics or air turbine motors, from the flap lever
Chapter 9 · Tabs, High-lift Devices and Spoilers
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Leading edge devices come in three main types. A Krueger flap is a panel in the lower surface near the leading edge that hinges down and forward, about its front edge. A variable camber flap is a flexible panel that bends as it extends, forming a well-curved nose. A slat is a section of the leading edge that moves forward on tracks, forming either a sealed leading edge or one with a slot, depending on how far it extends. Some aircraft combine them; one large airliner uses Krueger flaps inboard and variable camber flaps outboard. Leading edge devices are powered hydraulically or by air turbine motors driven by bleed air, and they are controlled by the same flap lever as the trailing edge flaps. Watch the scene: the slats move forward first, then the trailing edge flaps extend, first to a take-off setting and then fully.
Part 3 · Leading edge devices
Sequencing the leading edge with the flaps Trailing edge flaps Leading edge flaps Slats Retracted Retracted Retracted Intermediate (take-off) Fully extended Mid position (sealed), on many typesFully down (landing) Fully extended Fully extended (slotted)Retracting Sequence reversed Trailing edge first, leading edge last Alternate operation Standby hydraulics or electric drive Devices go fully out ; retraction may not be possible Autoslat — Slats run from mid to full near the stall angle of attack
Leading edge devices come out first and go in last , so the wing's leading edge is never left unprotected at high angle of attack.
Chapter 9 · Tabs, High-lift Devices and Spoilers
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The leading and trailing edge devices are sequenced together from the one flap lever. With the trailing edge flaps retracted, the leading edge devices are retracted too. When the trailing edge flaps move to an intermediate, take-off position, the leading edge flaps extend fully and, on many types, the slats go to a mid, sealed position. When the trailing edge flaps go fully down, the slats extend fully and open their slot. Retraction reverses the sequence, trailing edge first and leading edge last. If the normal system fails, the leading edge devices can be driven by a standby hydraulic system or, if they use air turbine motors, by an electric standby drive. They then extend fully, and depending on type it may not be possible to retract them again. Some aircraft also have an autoslat system, which runs the slats from the mid to the fully extended position if the angle of attack approaches the stall.
Part 3 · On the flight deck
Selectors and position indicators Flap lever on the centre pedestal, with gates or detents between positionsGates prevent inadvertent selection; typically three to five positions Speed brake lever also on the pedestalLarge pitch trim wheel ; smaller wheels or switches for rudder and aileron trim Positions shown on an electronic display or analogue dials
Electronic display
S
F
CONF 2
Analogue indicator (older types)
FLAPS
Flap lever on the pedestal:
gates (detents) between
positions stop accidental
selection; 3 to 5 positions.
Large pitch trim wheel;
small wheels or switches
for rudder and aileron trim.
Chapter 9 · Tabs, High-lift Devices and Spoilers
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the flight deck, the trim, flap and speed brake controls are grouped on the centre pedestal. Pitch trim usually has a large wheel, one on each side of the pedestal on many types, while rudder and aileron trim use smaller wheels or switches. The flap lever usually has a gate, or detent, between each position, so that it cannot be moved past a setting by accident; there are typically between three and five positions, depending on the type. The speed brake lever sits nearby. The positions of the slats and flaps are shown either on an electronic display, which on some aircraft shows little slat and flap symbols and the selected configuration, or, on older aircraft, on analogue dials with a needle for each side. Comparing the lever position with the indicator is how a crew spots a flap asymmetry lockout or a load relief retraction.
Part 4 · Spoilers
Spoilers for roll control Raised on the wing that must go down : the one with the up-going aileron A spoiler mixer drives them in proportion to aileron input; the other side stays down Advantages: no adverse yaw , less wing twist , work at transonic speed, cannot flutter They free the trailing edge for bigger flaps But they can only reduce lift: a roll always costs some lift
Wheel LEFT: spoiler mixer
spoilers up
aileron up
aileron down
spoilers stay down
rolls left
LEFT
RIGHT
Spoilers rise on the wing whose aileron goes UP
(the down-going wing), in proportion to wheel input.
On the other wing they stay retracted.
Typical: two flight spoilers per wing, inboard and
outboard pairs on different hydraulic systems,
each with a shut-off valve worked by a spoiler switch.
A follow-up linkage holds any intermediate angle.
Some aircraft use them only at low speed (flaps out).
Chapter 9 · Tabs, High-lift Devices and Spoilers
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Spoilers are panels on the upper surface of the wing that can be raised to disturb the airflow and reduce lift. For roll control, the spoiler is raised on the wing that has to go down, the one whose aileron goes up, and stays retracted on the other wing. A spoiler mixer, connected to the aileron system, drives the spoiler power units in proportion to the aileron movement. Watch the scene: the wheel goes left, the left aileron and the left spoilers rise, and the aircraft rolls left. Spoilers have several advantages over ailerons. There is no adverse yaw, because the raised spoiler adds drag on the down-going wing. The load is spread along the chord, so there is less wing twist. They keep working at transonic speeds, they cannot flutter, and they leave the trailing edge free for larger flaps. Their one drawback: they can only destroy lift, so every spoiler roll costs some lift.
Part 4 · Spoilers
Spoilers as speed brakes Used to slow down quickly (e.g. to rough air speed) or descend steeply (ATC, emergency descent) Speed brake lever raises the flight spoilers symmetrically Roll input still works: the spoilers on one side move further up Cleared up to V MO , but may blow back from full extension at high speed Profile drag: total drag up, V MD reduced , better low-speed speed stability
Drag curves: clean and speed brakes out
150
200
250
300
350
0
1
2
3
IAS (kt)
drag (relative)
V MD clean 220 kt
V MD 196 kt
speed brakes
Speed brake drag is profile drag: total drag up,
V MD down, so better speed stability at low speed.
Ideal: drag with no loss of lift or pitch change
(fuselage brakes); wing spoilers are the usual choice.
Chapter 9 · Tabs, High-lift Devices and Spoilers
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Speed brakes increase drag when the aircraft has to slow down quickly, for example to reach the rough air speed on meeting turbulence at high speed, or to descend steeply for air traffic control or in an emergency descent. Ideally a speed brake would add drag with no loss of lift and no change of pitch, which is what a fuselage-mounted brake does best. In practice the wing spoilers are used, because they are already there. A separate lever raises the flight spoilers symmetrically. Watch the scene: the spoilers rise together on both wings. Then a roll is commanded, and the spoilers on the down-going wing move further up, adding to the speed brake position. Speed brakes are normally cleared up to V M O, but may blow back from full extension at high speed. Their drag is profile drag, so the total drag rises and the minimum drag speed falls, which improves speed stability at low speed.
Part 4 · Spoilers
Ground spoilers and automatic deployment Lift dumpers : destroy wing lift, putting weight on the wheels for better braking , plus dragLocked out in flight: a shut-off valve opened by the weight-on-wheels switch Armed before landing: an actuator drives the lever to UP on wheel spin-up Backups: strut compression , thrust levers retarded, reverse selected Go-around : advancing the thrust levers retracts them; excess IAS protection
Automatic ground spoilers: the logic
Lever ARMED
before landing
Wheel spin-up
anti-skid signal
Strut compressed
air/ground backup
Thrust levers idle
or reversers selected
speed brake
actuator
lever to
UP: all
spoilers rise
Go-around: thrust levers advanced, so all spoilers retract.
Ground spoilers: shut-off valve opened only by the
weight-on-wheels switch. Excess IAS protection.
Chapter 9 · Tabs, High-lift Devices and Spoilers
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the landing run, the wheel brakes can only stop the aircraft as hard as the weight on the wheels allows, and any lift the wing is still making reduces that weight. Raising the spoilers dumps the lift, so the brakes work far better, and adds aerodynamic drag too. Many aircraft also have extra ground spoilers, used only on the ground. They are locked out in flight by a shut-off valve that only opens when the weight-on-wheels switch on the main gear senses the aircraft is on the ground. For landing, the crew arms the speed brake lever. Watch the scene: at touchdown, the wheels spin up, and the anti-skid system's signal energises an actuator that drives the lever fully up, raising all the spoilers. Backups are strut compression, retarding the thrust levers, and selecting reverse thrust. If the thrust levers are advanced for a go-around, all spoilers retract. There is also protection against deployment at excessive airspeed.
Summary
What to take into the exam Hinge moment Force × arm; force ∝ size × IAS². Set-back, horn, internal: less moment, same effect.
Tabs Balance: opposite, slight loss. Anti-balance: same way, heavier. Servo: tab only. Spring: helps at speed.
Mass balance Weight ahead of hinge: CG at or just ahead of it. Prevents flutter.
Trim Tab opposite to surface. Stabiliser trim: less drag, full elevator. Switches in pairs.
Mach trim CP aft at high Mach: tuck under. Stabiliser nose-up, with or without autopilot.
Flaps Two computers, power unit, torque shafts. Asymmetry and overspeed protection. Load relief.
Leading edge Krueger, droop, slats. Out first, in last. Alternate: fully out. Autoslat near stall.
Spoilers Up on the up-aileron wing. Speed brakes to V MO. Ground spoilers: weight on wheels, armed.
Chapter 9 · Tabs, High-lift Devices and Spoilers
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. The hinge moment is force times arm, and the force grows with surface size and the square of the indicated airspeed. Set-back hinges, horn balances and internal balances reduce the moment without losing effectiveness. A balance tab moves opposite to the surface and costs a little effectiveness; an anti-balance tab moves the same way and makes the controls heavier; a servo tab is the only thing the pilot moves; a spring tab helps most at high speed. Mass balance puts weight ahead of the hinge to prevent flutter. A trim tab moves opposite to the surface. Stabiliser trim gives less drag and keeps full elevator authority, with paired switches against runaway. Mach trim counters tuck under, autopilot or not. Flaps are driven by computers, a power unit and torque shafts, protected against asymmetry, with load relief. Leading edge devices come out first and in last. And spoilers rise on the wing with the up-going aileron, act as speed brakes, and dump lift on touchdown.