Aircraft Systems · Chapter 1
Structures, Loads and Design Philosophy How an airframe carries its loads: tension, compression, shear, bending and torsion, the limits it is designed to, the philosophies that keep it safe as it ages, and how fuselages and their windows are built.
frames · stringers · stressed skin
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the first lesson of Aircraft Systems. Before we look at hydraulics, landing gear or pressurisation, we need to understand the airframe that carries them all. In this lesson you will learn the basic loads every structure feels, how stress and strain are measured, and the limit and ultimate loads an airliner is designed to. Then we look at how designers keep an ageing airframe safe, with safe life, fail-safe and damage-tolerant structures, before we build a fuselage from its frames, stringers, skin, floor beams and seat rails and finish with the windows in front of you and beside the passengers.
Roadmap
How an airframe carries its loads 1 · Loads Tension, compression, shear, bending and torsion. Stress, strain and buckling.
2 · Limits Design limit load, design ultimate load and the 1.5 safety factor.
3 · Staying safe Fatigue, safe life, fail-safe and damage-tolerant design. Stations.
4 · The fuselage Hoop and axial stress, framework, monocoque, semi-monocoque, cut-outs and windows.
Chapter 1 · Structures, Loads and Design Philosophy
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson is in four parts. First the loads: the three basic loads of tension, compression and shear, and how bending and torsion combine them, together with stress, strain and buckling. Second, the limits an airframe is designed to: the design limit load, the design ultimate load and the safety factor of one point five that links them. Third, how designers keep a structure safe as it ages: fatigue, safe-life parts, fail-safe structure and damage-tolerant structure, and the station numbers engineers use to find any part of the aircraft. Finally we build the fuselage itself: the stresses pressurisation puts into it, the three ways of building it, how holes such as windows are reinforced, and how the flight-deck and cabin windows are made. Each part ends up in exam questions, so take your time.
Part 1 · Loads
Tension, compression and shear Tension stretches a member; a member built to resist it is a tie Compression shortens a member; a member built to resist it is a strut Shear tries to slide one face of the material over the nextRiveted joints are designed to carry shearEvery other load is a mixture of these three
Tension
stretches the member
a tie resists it
Compression
shortens the member
a strut resists it
Shear
slides one face over the next
riveted joints are designed to carry shear
shear plane
Chapter 1 · Structures, Loads and Design Philosophy
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every load on an airframe can be broken down into three basic loads. Tension is a pull that tries to stretch a member, and a member designed to resist tension is called a tie; a bracing wire is a good example. Compression is the opposite: a push that tries to shorten the member, and a member designed for it is called a strut. Shear is different. It tries to slide one face of the material over the face next to it, like scissors cutting paper. Look at the lapped joint at the bottom: the two plates are pulled in opposite directions, and the rivet joining them is loaded right across its shear plane. Riveted joints are designed to carry exactly this kind of load. Remember the names: tie for tension, strut for compression, rivets in shear. Every other load we meet is some mixture of these three.
Part 1 · Loads
Bending and torsion Bending combines all three: tension on the stretched side, compression on the squeezed side, shear acrossA wing bent up by lift: upper skin in compression , lower skin in tension Between them a neutral axis carries no direct stress Torsion is twisting: it sets up shear across the section, with tension and compression on the diagonalsExam wording: torsion produces tension, compression and shear together
Bending: a wing in flight
lift
upper side squeezed: compression
lower side stretched: tension
neutral axis
plus shear across the beam as it tries to split
Torsion: a twisting load
straight lines become helices: shear across every section,
with tension and compression on the diagonals
Chapter 1 · Structures, Loads and Design Philosophy
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Real structures rarely see a single pure load. Bending is the commonest combination. Picture a wing as a beam fixed at the fuselage and pushed up by lift. The upper side is squeezed, so it is in compression; the lower side is stretched, so it is in tension; and across the beam there is shear as the load tries to split it. Somewhere between the top and the bottom is the neutral axis, where the material is neither stretched nor squeezed. Hold on to that picture, because exam questions ask it directly: in flight the upper wing skin is in compression and the lower skin in tension. Torsion is a twisting load. Draw straight lines along a tube, twist it, and the lines become helices: every section is in shear, and on the diagonals that shear appears as tension one way and compression the other. That is why the exam says torsion produces all three basic loads.
Part 1 · Loads
Stress, strain and the elastic limit Stress = force ÷ area: the internal resistance to a load, in N/mm² or MN/m²Strain = change in length ÷ original length: a ratio, no unitsIn the elastic range stress ÷ strain is constant: Young's modulus Below the elastic limit the part springs back when unloaded Beyond it the deformation is permanent (permanent set)
0
2
4
6
8
10
12
0
100
200
300
400
500
strain (%)
stress (N/mm²)
elastic limit
permanent set
failure
elastic:
springs back
plastic: stays bent
Worked example: an aluminium alloy tie, area 200 mm², load 14 kN
stress = 14 000 N ÷ 200 mm² = 70 N/mm²
strain = 70 ÷ 70 000 (Young's modulus) = 0.001 : 1 mm per metre
Chapter 1 · Structures, Loads and Design Philosophy
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a load acts on a member, the material pushes back inside it. That internal resisting force per unit of area is called stress, and we measure it in newtons per square millimetre, or meganewtons per square metre, which is the same thing. A tensile load sets up tensile stress, a compressive load compressive stress, and so on. Strain is the deformation: the change in length divided by the original length, so it has no units. Look at the worked example. Fourteen kilonewtons on a tie of two hundred square millimetres gives a stress of seventy newtons per square millimetre. For an aluminium alloy, Young's modulus is about seventy thousand, so the strain is one in a thousand: one millimetre of stretch per metre. As long as we stay below the elastic limit, the part springs back when the load is removed. Load it beyond that limit and it is permanently deformed.
Part 1 · Loads
Buckling: when thin things give way sideways Buckling : a thin sheet or slender member under an end load bows sideways and collapsesIt happens to thin skins under compression, and to ties if they are pushed instead of pulled It can occur well below the material's crushing strength Stringers stiffen the skin; frames and ribs shorten its free lengthDouble the free length and the buckling load falls to a quarter
Thin sheet under end load
light load
buckled
Same skin with stringers
stringers stiffen the skin:
it carries far more load before buckling
Why length matters
length L
buckling load P
length 2L
buckling load P ÷ 4
A long, slender member loses stiffness fast: frames and ribs cut its free length.
Chapter 1 · Structures, Loads and Design Philosophy
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thin aircraft skins have a particular weakness: buckling. Push on the ends of a thin sheet and at first it simply shortens a little. Push harder and, long before the metal itself is crushed, the sheet suddenly bows out sideways and collapses. The same happens to a tie, a member designed only for tension, if it is ever loaded in compression. A wire or thin rod simply folds. Designers fight buckling in two ways. Stringers are riveted along the skin so that it becomes a stiffened panel, which carries far more load before it buckles. And frames and ribs are placed at intervals to cut the free length of each panel and each stringer. That matters a great deal, because for a slender member the buckling load falls with the square of its length: double the length and the load it can carry before buckling falls to a quarter.
Part 2 · Design limits
Limit load, ultimate load and the safety factor Design limit load (DLL): the largest load expected in service; no permanent deformation Transport aircraft: 2.5 g ; aerobatic: 6 g ; light aircraft in between Design ultimate load (DUL) = DLL × safety factor ; minimum factor 1.5 The structure must carry the DUL without collapse 70 t airliner: limit lift ≈ 1.72 MN , ultimate ≈ 2.58 MN
0 g
1 g
2 g
3 g
4 g
load factor n
1 g
straight and level
Design limit load 2.5 g
largest load expected in service
Design ultimate load 3.75 g
= limit × 1.5 safety factor
no permanent deformation
no collapse
Typical limit load factors
Transport
+2.5
Normal (light)
+3.8
Utility
+4.4
Aerobatic
+6.0
Chapter 1 · Structures, Loads and Design Philosophy
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Designers start from the design limit load. That is the largest load the aircraft is expected to meet in service, and it is set as a load factor in g. For a transport aircraft it is two point five g; for an aerobatic aircraft six g, with light aircraft in between. Up to the limit load the structure must not deform permanently. Then a safety factor is applied, at least one point five, to give the design ultimate load. Two point five times one point five is three point seven five g. Between limit and ultimate the structure may bend permanently, but it must not collapse. The safety factor is simply the ratio of ultimate load to limit load. Put numbers on it: a seventy tonne airliner at two point five g needs about one point seven meganewtons of lift, and its wings must carry about two point six meganewtons before they fail. Exam answer: the structure must survive the limit load times one point five.
Part 3 · Staying safe
Three ways to keep an ageing structure safe Every structure is slowly worn by repeated loads. Designers choose one of these approaches, or a mixture, for each part.
Safe life Prove a minimum life in hours, landings, pressurisation cycles or calendar time, then replace the part before it is reached.
Fail-safe Give the load more than one path . If one member fails, its neighbours carry the load until the next inspection.
Damage tolerant Spread the load over a large area so cracks grow slowly and predictably , and inspect often enough to find them.
Chapter 1 · Structures, Loads and Design Philosophy
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
An airframe is loaded and unloaded thousands of times: every flight, every pressurisation, every landing. Even if no single load comes near the limit, these repeated loads slowly wear the structure out, so designers need a strategy to keep it safe for its whole life. There are three. A safe-life part is proven to last a minimum number of hours, landings, pressurisation cycles or years, and is then replaced before that life is reached. A fail-safe structure gives the load more than one path, so if one member cracks the others carry its share until the next inspection finds the damage. A damage-tolerant structure spreads the load over a large area so that cracks grow slowly and predictably, and the inspections are spaced so that a crack is always found before it becomes dangerous. Large modern aircraft use a mixture: safe life for parts such as the landing gear, and fail-safe or damage-tolerant design for the airframe.
Part 3 · Staying safe
Safe life Safe life : the minimum life during which no catastrophic failure is expectedCounted in flying hours , landings , pressurisation cycles or calendar time When the count is reached the part is replaced or overhauled , whatever its condition Typical: landing gear, engine discs, some fittings that cannot be duplicated Inspections continue in the interim, and fail-safe or damage-tolerant design limits the risk
A safe-life part has a life count
flying hours
e.g. 30 000 h
landings
gear, wheels
pressurisation cycles
fuselage
calendar time
rubber, seals
Its life is spent like a budget
cycles used
safe life reached:
replace or overhaul
inspections continue in the interim
Safe life = the minimum life during which no catastrophic
failure is expected, with a large scatter margin built in.
Chapter 1 · Structures, Loads and Design Philosophy
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The safe life of a structure is the minimum life during which we know that no catastrophic damage will occur. It is established by testing and calculation, with a large margin for scatter, because two apparently identical parts never fail at exactly the same moment. The life is counted in whatever unit wears the part: flying hours, landings, pressurisation cycles, or simply calendar time for rubber and sealants. When the count is reached, the part is replaced or overhauled, even if it looks perfect. Typical safe-life items are landing gear legs, engine discs and some fittings that cannot sensibly be duplicated. During the operating life the aircraft is still inspected, and the rest of the airframe is designed on fail-safe or damage-tolerant lines to keep the chance of fatigue failure low. For the exam: a safe-life part should not fail until its predicted number of cycles, and it is changed before that life is reached.
Part 3 · Staying safe
Fatigue: death by a thousand cycles Fatigue : repeated load reversals make a part fail at a load below its static strengthThe higher the alternating stress, the fewer cycles to failure 80 % of ultimate: about 100 cycles ; 20 %: about 10 million Fuselage fatigue life is set by pressurisation cycles A long-haul design used on short haul collects cycles far faster than it was designed for
101
102
103
104
105
106
107
108
0
20
30
50
80
cycles to failure N (log scale)
alternating stress (% of ultimate)
80 % → 100 cycles
20 % → 10 million
Same aircraft type, same design life of 60 000 cycles:
short haul, 8 sectors a day ≈ 2 920 cycles a year → about 20 years
long haul, 1.5 sectors a day ≈ 550 cycles a year → over 100 years
It is the number of load reversals, not the hours, that uses up a fuselage.
Chapter 1 · Structures, Loads and Design Philosophy
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
A structure that is loaded and unloaded over and over again will fail at a much lower load than one loaded steadily. That is fatigue. The graph, called an S N curve, shows how strongly it depends on the size of the alternating stress. At eighty per cent of the ultimate stress, a specimen might fail after only about a hundred cycles. Reduce the stress to twenty per cent and it survives about ten million. For a fuselage the important cycle is the pressurisation cycle: every flight inflates the cabin and lets it down again. So the fatigue life of an airliner fuselage is based on pressurisation cycles, not on flying hours. Now look at the worked example. A type designed for sixty thousand cycles lasts about twenty years flying eight short sectors a day, but more than a hundred years on long haul. That is why a long-haul aircraft moved onto short-haul work is a concern: its structure was not designed for that stress pattern.
Part 3 · Staying safe
Fail-safe structure: more than one load path If any one member fails, its load is carried by adjacent members The survivors carry normal loads until the next scheduled inspection Relies on a programmed inspection to find the failure True dual load paths at wing, fin and tailplane attachments Drawback: duplicated members are heavy
Several members share the load
33%
33%
33%
load
intact
50%
50%
load
one member cracked
Each surviving member is sized to carry the extra share
safely until the next scheduled inspection finds the crack.
Typical places: wing-to-fuselage and tail attachment fittings.
Chapter 1 · Structures, Loads and Design Philosophy
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
A fail-safe structure is one in which no single member carries the whole load. Look at the scene: a fuselage frame is joined to a wing attachment fitting by three members, and the load is shared between them. Now one member cracks. Its share of the load does not vanish; it moves to the adjacent members, which glow as they take the extra load. They are sized so that they can carry the normal operating loads safely for a limited time, until the next scheduled inspection finds the crack and it is repaired. So a fail-safe structure depends on a planned inspection programme; on its own it does not stop parts failing, it stops one failure becoming a catastrophe. True dual load paths are used where it matters most, at the wing, fin and tailplane attachments. The price is weight, because every duplicated member is extra metal.
Part 3 · Staying safe
Damage tolerance: find the crack in time Spreads the load over a large area instead of adding duplicate members: lighter than fail-safe Damage grows slowly and predictably and is found at normal inspections Inspection interval set so a crack missed once is still found before it is critical Tear stoppers and reinforcing plates halt cracks in the skinLimit loads, ultimate loads and inspection intervals are agreed at certification
0k
10k
20k
30k
40k
0
10
20
30
40
50
60
70
flight cycles
crack length (mm)
detectable at inspection (10 mm)
critical length (60 mm)
found
second chance
Inspections every 7 500 cycles (green ticks).
The crack becomes detectable after 20 000 cycles and critical after 35 500,
so even if one inspection misses it, the next still finds it in time.
The structure spreads the load and grows cracks slowly and predictably.
Chapter 1 · Structures, Loads and Design Philosophy
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fail-safe structure is heavy because of its extra members. Damage-tolerant design gets the same safety in a lighter way: the load is spread over a large area of skin, stringers and frames, so that if a crack starts, it grows slowly and predictably and the rest of the structure carries on. The key is the inspection interval. Follow the graph. The crack is too small to see until twenty thousand cycles, and it would become critical at about thirty five and a half thousand. Inspections every seven and a half thousand cycles mean it is found at twenty two and a half thousand, and even if that inspection misses it, the next one at thirty thousand still finds it before it is dangerous. Strips called tear stoppers are fitted round the fuselage to stop a running crack. The inspection intervals, limit loads and ultimate loads are all agreed when the type is certified.
Part 3 · Staying safe
Safe life, fail-safe and damage tolerant compared Safe life Fail-safe Damage tolerant Idea Replace before the proven life Alternative load paths Load spread; slow, predictable crack growth If a part cracks Should not happen within its life Neighbours carry the load Rest of the structure carries on How damage is found Life count, plus inspections Programmed inspections Normal inspection cycles Weight Can be heavy (big margins) Heavy (duplicate members) Lightest Typical use Landing gear, engine discs Wing and tail attachments Modern fuselage and wing skins Exam phrase Changed before its life is reached Redundant strength tolerates damage Redundancy spread over a large area
Modern transport aircraft combine all three. Classic fail-safe design with fully duplicated members has largely been replaced by damage-tolerant design.
Chapter 1 · Structures, Loads and Design Philosophy
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the three philosophies side by side. Safe life replaces a part before its proven life is reached; it should not crack within that life, and it is used for things like landing gear and engine discs. Fail-safe structure provides alternative load paths, so when one member cracks its neighbours carry the load until a programmed inspection finds it; it is heavy because of the duplicated members, and you find it at wing and tail attachments. Damage-tolerant structure spreads the load over a large area, so cracks grow slowly and are found during the normal inspection cycles; it is the lightest of the three and is used for most modern fuselage and wing skins. Learn the exam phrases in the bottom row. And note the historical point: classic fail-safe design, with every member duplicated, has largely been replaced in new passenger aircraft by damage tolerance, although true dual load paths remain at the critical attachments.
Part 3 · Finding your way
Station numbers, water lines and buttock lines A grid for locating any structure or component for maintenance and repair Fuselage stations : inches from a zero datum at or near the nose; + aft, − forwardWater lines (WL): heights in inches above a horizontal datumButtock lines (BL) or wing stations: inches left or right of the centre lineExample: a frame at FS 500 is 500 inches aft of the datum
Side view: fuselage stations and water lines
FS 0
datum
+100
+300
+500
+700
inches aft of the datum (+); forward of it (−)
WL 0
WL 70
Top view: buttock lines (wing stations)
BL 0
LBL 50
RBL 50
Chapter 1 · Structures, Loads and Design Philosophy
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
When an engineer finds damage, or a manual tells them where a component is, they need an exact address on the airframe. That address comes from reference lines. Fuselage stations are measured in inches along the fuselage from a zero datum, fuselage station nought, at or near the nose as the manufacturer defines it. Stations aft of the datum are positive and any forward of it are negative, so a frame at station five hundred is five hundred inches aft. Water lines give heights, in inches above a horizontal datum, and buttock lines, also called wing stations, give distances in inches left or right of the aircraft centre line. Put the three together and every rib, frame and bracket has a unique position. For the exam, remember simply that station numbers and water lines are a means of locating airframe structure and components; they have nothing to do with seats, runways or compasses.
Part 4 · The fuselage
What the fuselage does Its primary purpose: to house the crew and payload in safe, comfortable conditions A place to fly from, and space for controls, systems and equipment It transfers loads to and from the wings, tail, landing gear and, on some types, the engines In a pressurised aircraft it is a pressure vessel : hoop and axial stresses The pressure hull runs between the forward and aft pressure bulkheads
The fuselage gathers every load
FUSELAGE
wings
lift, drag, fuel, engines
tailplane and fin
trim and control loads
landing gear
landing, braking, taxi
payload and crew
cabin, cargo, pressure
and in a pressurised aircraft it is also a pressure vessel
Chapter 1 · Structures, Loads and Design Philosophy
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fuselage is the main body of the aircraft, and its primary purpose is to house the crew and the payload, passengers or freight, in safe and comfortable conditions. It also gives the pilots an effective place to fly from and provides space for the flying controls, systems and equipment. Structurally, it is the junction box of the airframe: it transfers loads to and from the wings, the tailplane and fin, the landing gear, and on some types the engines. Watch the scene as the skin turns transparent and we look inside. The pressure hull glows: in a pressurised aircraft the fuselage between the forward and aft pressure bulkheads is a pressure vessel. The cargo holds are inside it too. The wheel wells, on the other hand, are outside the pressure hull, sealed off from it. Being a pressure vessel adds two more stresses to the fuselage, which we look at next.
Part 4 · The fuselage
Hoop and axial stress Cabin pressure pushes outwards on every square centimetre of the hull Hoop (radial) stress tends to expand the cross-section: taken by skin and frames Axial (longitudinal) stress tends to lengthen the fuselageIn a cylinder the hoop stress is twice the axial stress Differential pressure can reach about 9.5 psi (65.5 kN/m²)
Cut through a pressurised fuselage
ΔP
hoop
stress
axial stress
pressure on the domed
bulkhead pulls the barrel longer
Thin cylinder: hoop = ΔP·r ÷ t, axial = ΔP·r ÷ 2t
ΔP = 60 kPa (8.7 psi), radius 2.0 m, skin 1.6 mm:
hoop = 60 000 × 2.0 ÷ 0.0016 = 75 N/mm²
axial = half of that = 37.5 N/mm²
Hoop stress is twice the axial stress: frames take it round the barrel.
Chapter 1 · Structures, Loads and Design Philosophy
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the cabin is pressurised, the air inside pushes outwards on every part of the hull. Watch the arrows: the cabin pressure pushes on the skin all the way round. That sets up hoop stress, sometimes called radial stress, which tries to expand the cross-section like a balloon being blown up; it runs round the barrel and is carried by the skin and the frames. The pressure also pushes on the domed rear bulkhead and the nose, trying to pull the barrel longer; that is the axial, or longitudinal, stress. For a thin cylinder the hoop stress is twice the axial stress. Look at the worked example: a differential of sixty kilopascals, about eight point seven psi, in a fuselage of two metres radius with a skin one point six millimetres thick gives a hoop stress of seventy five newtons per square millimetre and an axial stress of half that. Maximum differentials of around nine and a half psi are common.
Part 4 · The fuselage
Framework (truss) construction Light-gauge steel tubes welded into a space frame of trianglesThe triangle is the most rigid shape: each tube carries a definite load Which tubes are in tension or compression changes between air and ground Covered with fabric or light alloy for a clean, enclosed shape Strong, easy to build, trouble-free: used on light, unpressurised aircraft
Welded steel-tube space frame
longerons
diagonals make triangles
welded joints
Strength
the tubes carry the loads; the skin only shapes it
Cover
fabric or light alloy sheet
Pros
strong, easy to build and repair
Use
light, unpressurised aircraft
Chapter 1 · Structures, Loads and Design Philosophy
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two main ways to build a fuselage. The first is the framework, or truss. Light-gauge steel tubes are welded together into a space frame made of triangles. The triangle is the most rigid geometric shape, because it cannot change shape without one of its sides changing length, so every tube carries a definite load in tension or compression. Which tubes are in tension and which in compression changes depending on whether the aircraft is flying or sitting on the ground. The frame is then covered with fabric or thin light alloy, which gives an enclosed, aerodynamically clean compartment but carries little or no load itself. The result is strong, easy to build and repair, and relatively trouble-free. It is ideal for light, slow, unpressurised aircraft, many vintage two-seaters among them, but it wastes the inside space and cannot be a pressure vessel.
Part 4 · The fuselage
Monocoque: the skin carries it all Monocoque : all the loads are carried by the skin Only light formers inside, to give the shape Even slight damage to the skin can seriously weaken it Sandwich skins: honeycomb core between face sheets of GRP, CFRP or light alloyUsed on some all-composite light and business aircraft
Monocoque: the shell does the work
skin carries all the loads
light formers: shape only
a small dent weakens the whole shell
Sandwich skin
face sheet: GRP, CFRP
or light alloy
honeycomb core
Stiff and light: e.g. an all-composite business turboprop
Chapter 1 · Structures, Loads and Design Philosophy
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The second family is stressed-skin construction, and its pure form is the monocoque, from the French for a single shell. In a monocoque the skin carries all the loads, like an egg shell or a drinks can. Inside there are only light formers, whose job is simply to give the shape. It makes very efficient use of material, but it has one serious weakness: because the skin is doing everything, even slight damage, a dent or a crack, can seriously weaken the whole structure. Modern materials have revived the idea. A sandwich skin, with a light honeycomb core bonded between two thin face sheets of glass fibre, carbon fibre or light alloy, is very stiff for its weight, and some all-composite light and business aircraft use a monocoque built this way, such as one well-known canard turboprop executive aircraft. But for large aircraft we need something more robust.
Part 4 · The fuselage
Semi-monocoque: frames, stringers and skin The usual structure of large aircraft : skin reinforced by frames, stringers and longerons Frames (formers) give the shape and oppose hoop stress Stringers run lengthwise, stiffen the skin and help it carry loads along its lengthLongerons : heavier lengthwise members, e.g. the seat rails The skin is primary structure, riveted or bonded on; bulkheads close off sections
pressurised cabin
cargo hold
skin
frame
stringer
floor beam
seat rails
(longerons)
Frames: shape + hoop loads · stringers: stiffen skin lengthwise
skin: primary structure, riveted or bonded to both
Chapter 1 · Structures, Loads and Design Philosophy
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
As aircraft grew larger, the pure monocoque was not strong enough, so lengthwise members were added, and the result, semi-monocoque construction, is what almost every large aircraft uses today. Watch the section build up. The skin is the outer shell, and it is still primary load-bearing structure carrying much of the load. Inside it, the frames, or formers, give the fuselage its shape and resist the hoop stresses of pressurisation; that is their main purpose. Running along the fuselage are the stringers, which stiffen the skin against buckling and help it carry loads along its length. Heavier lengthwise members are called longerons, and the seat rails on the floor beams are good examples. The skin is riveted or adhesive-bonded to the frames and stringers, and stronger bulkheads close off sections such as the pressure hull. If an exam asks what large fuselages are made of, the answer is semi-monocoque structure.
Part 4 · The fuselage
Cut-outs, doublers and reinforcement Every hole for a window, door or access panel interrupts the load path Stress concentrates at the edge of a cut-out, so it must be reinforced Doublers or backing plates are fitted round the holeMachined skins are left thicker around windows and doors Intercostals between frames and window support frames carry the load round; repairs use doublers too
A window belt in the skin
frame
doubler
intercostal
stringer
Cut-out
a hole breaks the load path: stress piles up at its edge
Doubler
a reinforcing plate riveted round the hole
Machined skin
left thicker round windows and doors
Repair
a damaged area is cut out and doubled
Chapter 1 · Structures, Loads and Design Philosophy
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
A stressed skin works because the load flows smoothly through it. Cut a hole in it, for a window, a door or an access panel, and the load has to flow around the hole, piling up at its edges, exactly where fatigue cracks love to start. So every cut-out must be reinforced. The classic method is a doubler, a reinforcing plate riveted around the edge of the hole. When skin panels are machined from solid, the metal around the windows is simply left thicker instead. Look at the window belt in the drawing: each window sits between two frames, with a doubler round it, and short members called intercostals run between the frames above and below the windows to carry the load across. Rounded window corners help too, because sharp corners concentrate stress. The same principle applies to repairs: damaged skin is cut out and the area is reinforced with a doubler.
Part 4 · Windows
Flight-deck windows Must take pressurisation loads and birdstrike impact Toughened glass plies bonded each side of a clear vinyl interlayer A conducting coating on the inside of the outer ply heats the window Heat prevents ice and misting and keeps the vinyl resilient : best impact resistance with heat on If the glass shatters, the vinyl stretches and absorbs the shock; the panel is bolted into its frame
Section through a flight-deck windscreen
outer glass ply
heating film (inside of outer ply)
vinyl interlayer
inner glass ply (structural)
vinyl
inner glass ply
frame, bolted
bird
outside
cabin side
Glass
toughened: hard, scratch resistant, heavy
Vinyl
stretches and holds the pieces if a ply breaks
Heat
stops ice and fog; warm vinyl is tougher
Light aircraft
acrylic (Perspex): light, but scratches
Chapter 1 · Structures, Loads and Design Philosophy
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flight-deck windows of a pressurised aircraft have two jobs: they must carry the pressurisation load, and they must survive a birdstrike. Watch the layers pull apart. On the outside is the outer ply of toughened glass. On its inner face is a thin, transparent, electrically conducting film that heats the window. Behind that is a thick layer of clear vinyl, then a thick structural glass ply, and inner plies on the cabin side. The heating keeps ice and mist off, but it also keeps the vinyl warm and resilient, and that is what absorbs the shock of a bird. If the impact is hard enough to shatter the glass, the vinyl interlayer stretches and deforms, holding the pieces together. So a windscreen is most impact resistant with its heating switched on. Glass is heavier than acrylic, but harder and more scratch resistant. The whole laminated panel is bolted into the frame through its edge.
Part 4 · Windows
Birdstrike rules and the pilot's view Withstand a 4 lb (1.8 kg) bird without penetration At VC at sea level or 0.85 VC at 8 000 ft , whichever is worse Then continue to a safe flight and landing Each pilot needs a clear, undistorted view for all manoeuvres; an opening window may be fitted Large aircraft: laminated glass ; light aircraft: acrylic (Perspex)
The windscreen birdstrike case
4 lb (1.8 kg) bird, no penetration, at the worse of:
V C at sea level
or
0.85 V C at 8 000 ft
then continued safe flight and landing
How hard is that?
At 300 kt (154 m/s): energy = ½ × 1.8 × 154² ≈ 21 kJ
about the same as a one-tonne car hitting a wall at 24 km/h.
Other rules for the flight-deck view
• Clear, undistorted view for every manoeuvre in the envelope
• An opening (direct vision) window may be fitted for landing
if the windscreen is obscured
• Heating on: the windscreen is at its most impact resistant
Chapter 1 · Structures, Loads and Design Philosophy
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The certification rule for the windscreen is specific. The aircraft must be able to continue safe flight and landing after hitting a four pound bird, about one point eight kilograms, at the design cruising speed V C at sea level, or at nought point eight five V C at eight thousand feet, whichever is more critical. In practice that means the windscreen must not be penetrated. To feel what that means, look at the numbers: a one point eight kilogram bird at three hundred knots carries about twenty one kilojoules, roughly a one tonne car hitting a wall at twenty four kilometres per hour. The windscreen angles are also specified so that each pilot has a clear, undistorted view for every manoeuvre, and an opening window may be fitted so the pilot can land if the forward view is lost. Large commercial aircraft use laminated glass; light aircraft generally use acrylic, often called Perspex, which is lighter but scratches easily.
Part 4 · Windows
Cabin windows: fail-safe by design Normally two acrylic panes in an airtight rubber seal and a metal frame Each pane can carry the full cabin pressure loadIf one pane fails, the other holds the pressure : a fail-safe design A small breather hole in the inner pane lets the outer pane take the load normally A thin scratch pane on the cabin side protects them from passengers
Section through a cabin window
outside
cabin
outer pane
inner pane
rubber seal
scratch pane
breather hole
Two acrylic panes in a rubber seal and a metal frame
Each pane can carry the full pressure load; the outer normally works
If one fails the other holds: a fail-safe window
Chapter 1 · Structures, Loads and Design Philosophy
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Passenger windows are small, but there are a great many of them, so each one is designed to be fail-safe. A typical cabin window has two panes of acrylic plastic mounted in an airtight rubber seal, which sits in a metal window frame in the skin. The important point is that the outer pane and the inner pane are each strong enough to carry the full cabin pressurisation load on their own. A tiny breather hole in the inner pane lets the pressure reach the gap, so in normal flight the outer pane does the work and the inner pane is the back-up. If the outer pane cracks, the inner pane takes over and the cabin stays pressurised. On the cabin side there is usually a thin scratch pane that is not structural at all; it just protects the real panes from passengers' fingers and rings. So: two panes, each able to take the full load, which makes the window fail-safe.
Summary
Structures in a nutshell Loads Tie: tension. Strut: compression. Rivets: shear. Wing in flight: top skin compression, bottom tension.
Stress and strain Stress = force ÷ area. Strain = ΔL ÷ L. Beyond the elastic limit: permanent set. Thin sheets buckle.
Limits Limit 2.5 g transport, 6 g aerobatic. Ultimate = limit × 1.5, no collapse.
Ageing Fatigue counted in pressurisation cycles. Safe life: replace. Fail-safe: other paths. Damage tolerant: spread load, inspect.
Fuselage Semi-monocoque. Frames: shape and hoop stress. Stringers stiffen skin. Hoop stress = 2 × axial.
Windows Glass–vinyl–glass, heated: tougher. 4 lb bird at V C. Cabin: two acrylic panes, each takes full load.
Chapter 1 · Structures, Loads and Design Philosophy
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull the lesson together. A tie resists tension, a strut resists compression, and rivets carry shear; a wing in flight has its upper skin in compression and its lower skin in tension. Stress is force over area, strain is change of length over length, and beyond the elastic limit the deformation is permanent; thin sheets fail by buckling. The design limit load is two point five g for transport aircraft, and the ultimate load is one point five times that, carried without collapse. Fatigue is counted in cycles, and for a fuselage that means pressurisation cycles. Safe-life parts are replaced, fail-safe structures provide other load paths, and damage-tolerant structures spread the load and rely on inspection. Large fuselages are semi-monocoque, with frames resisting hoop stress, which is twice the axial stress. Windscreens are heated glass and vinyl laminates, and cabin windows have two panes that can each carry the full load. Now try the quiz.