Aircraft Systems · Chapter 6
Wheels and Tyres How aircraft wheels are built and protected by fusible plugs, how a tyre is made and marked, why pressure and nitrogen matter, and how to recognise creep, wear, damage and aquaplaning.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter six is about wheels and tyres. They look simple, but an airliner tyre carries many tonnes at well over one hundred and fifty knots, at pressures five or six times higher than a car tyre, and it sits beside a brake that can glow red hot. We will see how wheels are built so that tyres can be changed, and how fusible plugs stop an overheated tyre from bursting. Then we take a tyre apart, read the markings on its sidewall, and learn why the correct pressure, checked the correct way, prevents most tyre failures. Finally we look at creep, wear, damage and aquaplaning, with the aquaplaning speed calculations that the exam loves.
Chapter 6 roadmap
Wheels and tyres in five parts 1 · Wheels Flange and divided wheels, materials, tubeless wheels and fusible plugs .
2 · Building a tyre Tread, breakers, casing plies , beads; cross-ply and radial; ply rating ; tread patterns.
3 · Tubes, tubeless, markings Inner tubes and valves, tubeless advantages, pressure categories and sidewall marks .
4 · Pressure and creep Rated pressure, the +4% and +10% rules, nitrogen, and creep with its limits.
5 · On the runway Aquaplaning and its speed, wear patterns, damage limits, taxying and tyre speed limits.
Exam focus Vp = 9√P , the 4% allowance, creep marks, awl vents, scrubbing, dry powder near hot wheels.
Chapter 6 · Wheels and Tyres
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the route through this chapter. We start with the wheels themselves: how they are built so that a tyre can be changed, what they are made of, what is special about a wheel for a tubeless tyre, and the fusible plugs that stop an overheated tyre from bursting. Then we take a tyre apart: the tread, the breaker strips, the casing plies and the beads, the difference between cross-ply and radial construction, what a ply rating really means, and the tread patterns. Part three covers inner tubes, the advantages of tubeless tyres, the pressure categories and the markings on the sidewall. Part four is all about pressure: the rated pressure, the four per cent and ten per cent allowances, why we use nitrogen, and creep. Finally we take the tyre onto a wet runway, calculate the aquaplaning speed, and look at wear, damage and the habits that make tyres last.
Part 1 · Wheels
What wheels and tyres do Support the aircraft on the ground and give mobility for taxying, take-off and landing Pneumatic tyres cushion shocks from rough surfaces (and rough landings) Main wheels, and sometimes nose wheels, house the brakes Inflated with nitrogen : dry, inert, no internal oxidation or fire risk, steadier pressure The cover restrains the gas, keeps the shape, transmits braking and gives a wearing surface
axle
nitrogen at high pressure
tyre
wheel (two halves)
Brake stack inside the wheel: heat soaks into the rim and the tyre
brake
Chapter 6 · Wheels and Tyres
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Wheels and tyres support the aircraft on the ground and give it mobility for taxying, take-off and landing. Because the tyres are pneumatic, they also cushion the shocks from uneven surfaces, and now and then from a less than perfect landing. The main wheels, and on some aircraft the nose wheels too, house the brakes, as you can see in the cutaway: the brake stack sits inside the wheel rim, so its heat soaks straight into the wheel and the tyre. Aircraft tyres are normally inflated with nitrogen rather than air. Nitrogen is dry and inert, so there is no moisture to freeze or corrode, no oxygen to attack the rubber from inside or to feed a fire if the brakes overheat, and the pressure changes less with temperature. The gas carries the load and absorbs shocks, while the cover holds the gas in, keeps the shape, transmits the braking force to the runway and provides the wearing surface.
Part 1 · Wheels
Flange wheels and divided wheels Wheels are designed so the tyre can be changed easily Loose flange : one flange integral, the other held by a locking ring Detachable flange : the removable flange is bolted on (one, two or three pieces)Divided wheel : two halves bolted together with stiff (nyloc) nuts or locking platesFor tubeless use, a seal at the joint makes it airtight; for a tube, the wheel valve is removed and the tube valve fitted through the rim
Loose / detachable flange
integral flange wheel body (rim)
removable flange → loose: locking ring · detachable: bolts
Divided (split) wheel
O-ring seal at the joint
two halves bolted together (stiff or nyloc nuts)
valve in the wheel
Chapter 6 · Wheels and Tyres
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aircraft wheels are designed first of all so that the tyre can be changed easily, and they fall into two families. In the loose and detachable flange wheel, one flange is part of the wheel body and the other is a separate ring that slides over the rim. The difference between the two names is only how that ring is held: a loose flange is retained by a locking device on the rim, and a detachable flange is bolted to the wheel body, and may itself be made of one, two or three pieces. The divided wheel is made of two half wheels, matched and clamped together by bolts through both halves, with stiff nuts, or with locking plates where one half is threaded. When a divided wheel is used with a tubeless tyre, a seal in the joint stops the halves chafing and makes the joint airtight. If it is used with a tube instead, the wheel valve is removed and the tube valve passes through the rim.
Part 1 · Wheels
Wheel materials and tubeless wheels Cast or forged , then machined: aluminium alloy or magnesium alloy (Electron)Corrosion protection: anodising (aluminium), chromate treatment (magnesium), then cellulose or epoxy paint Tubeless wheels: finer finish , impregnated with Bakelite to seal the metal O-ring seals between the wheel parts stop leakageThe valve is in the wheel , so creep cannot damage it Anti-creep design: knurled flange faces and a tapered bead seat
tyre bead
taper wedges the bead outward onto the rim
knurled flange face
O-ring seal
valve in the wheel
Bakelite-impregnated, finely finished metal
Chapter 6 · Wheels and Tyres
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Wheels are cast or forged and then machined and ground to a fine finish. The materials are aluminium alloy, or magnesium alloy, sometimes called Electron, which is lighter but more prone to corrosion. After machining, each wheel gets an anti-corrosion treatment: anodising for aluminium alloy and chromate treatment for magnesium alloy, followed by a finish of cellulose or epoxy paint. A wheel for a tubeless tyre must itself hold the gas, so it is ground to a finer finish and impregnated with Bakelite to seal any porosity in the metal, and O-ring seals are fitted between the wheel parts. The inflation valve is built into the wheel, so tyre creep cannot tear it out. Wheels can also be designed to resist creep: the inner face of the flange may be knurled so that the side pressure of the tyre locks the bead to it, and the bead seat may be tapered, so that inflation wedges the bead outward to grip the rim.
Part 1 · Wheels
Fusible plugs: deflate, do not explode Very hard braking can heat the wheel and tyre enough to cause a blow-out Fusible (thermal) plugs in tubeless wheels are held by an alloy that melts at a set temperatureThe tyre pressure then blows the plug out: controlled, slow deflation They react to high temperature , not to pressure Colour coded: red 155 °C , green 177 °C , amber 199 °C Heat soaks into the wheel after the stop: the risk peaks some minutes later
50 100 150 200 250
0 20 40 60 80 100 120
155 °C 177 °C 199 °C
plug colours: red 155 · green 177 · amber 199 °C
wheel peaks well after the stop
minutes after the stop
wheel temperature (°C)
Chapter 6 · Wheels and Tyres
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Under extra hard braking, such as a rejected take-off at high weight, so much heat flows from the brake into the wheel and tyre that the gas pressure could rise until the tyre bursts, with possibly catastrophic results. To prevent this, many tubeless wheels carry fusible plugs, also called thermal plugs. Each plug is held in the wheel by a fusible alloy that melts at a set temperature; the tyre pressure then blows the plug out, and the tyre deflates in a controlled way instead of exploding. So a fusible plug reacts to high temperature, not to high pressure. Plugs come in three temperatures, colour coded for identification: red melts at one hundred and fifty-five degrees Celsius, green at one hundred and seventy-seven, and amber at one hundred and ninety-nine. The graph shows that heat keeps soaking into the wheel after the stop, so plugs often melt many minutes later.
Part 2 · Building a tyre
Inside a tyre
Tread
Breaker strips
Casing plies
Inner liner
Apex strip
Bead wires
Chafer strip
the wearing surface; grooves
absorb and spread shocks
rubberised cords: the strength
holds the gas (tubeless)
stiffens the bead
copper-plated steel coils
protects the bead from the rim
Crown Shoulder Sidewall Bead
Cords in each ply are laid parallel, not woven, and separated by a thin film of rubber so they cannot cut one another.
Chapter 6 · Wheels and Tyres
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a tyre cut through. The strength comes from the casing, layers or plies of rubberised cords of cotton, rayon or, today, nylon. The cords in each ply are laid parallel, not woven, and each ply is coated in a thin film of rubber so the cords of neighbouring plies do not cut one another as the tyre flexes. Between the casing and the tread are two narrow breaker strips, embedded in thick rubber, which absorb and spread load shocks and protect the casing from concussion damage. The plies are anchored by wrapping them round inextensible coils of steel wire to form the bead; the wires are copper plated and bonded with rubber. A rubber apex strip above the bead stiffens it and smooths the change of section, and chafer strips of rubberised fabric protect the bead where it sits on the rim. On a tubeless tyre an inner liner holds the gas. The regions are named crown, shoulder, sidewall and bead; the tread covers the crown and shoulders.
Part 2 · Building a tyre
Cross-ply, radial and the ply rating Plies are fitted in pairs Bias (cross-ply) : cords of adjacent plies at 90° to each other , running diagonallyRadial : cords run bead to bead at about 90° to the centre line Ply rating is an index of the tyre's strength , not the number of pliesExample: a 49 × 17 tyre of 32 PR has only 18 plies
Bias (cross-ply) Radial
adjacent plies cross at 90° cords bead to bead, ~90° to rim
Ply rating = an index of strength, not a ply count
49 × 17 32 PR as marked
only 18 actual plies plies fitted in pairs
Chapter 6 · Wheels and Tyres
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two ways of arranging the casing cords. In a bias, or cross-ply, tyre, the plies are fitted in pairs with the cords of neighbouring plies running diagonally at ninety degrees to each other, so they form a criss-cross net. In a radial tyre the cords run straight from bead to bead, at about ninety degrees to the centre line of the tyre, and a belt under the tread holds the shape. Radial tyres are lighter and run cooler, which is why many modern airliners use them. Now a classic exam trap: the ply rating. The manufacturer gives each tyre a ply rating, but it does not tell you how many plies there are. It is simply an index of the tyre's strength, dating from the days of cotton cords. Modern cords are much stronger, so fewer plies give the same strength. For example, a forty-nine by seventeen tyre with a ply rating of thirty-two actually has only eighteen plies.
Part 2 · Building a tyre
Tread patterns "Tread" means the crown rubber, plain or patterned Ribbed : circumferential grooves, the most popular; disperses water, helps prevent aquaplaning , improves gripDiamond (block): the older all-weather patternChined nose tyres deflect spray from rear-mounted engines ; a single nose wheel has chines on both sidesMarstrand twin-contact tyre: resists shimmy; renew when worn to the bottom of the central groove
Ribbed most popular Diamond all-weather Chined chine on shoulder Marstrand twin contact
Grooves disperse water and help prevent aquaplaning
Chine: deflects spray from rear-mounted engine intakes
Marstrand: renew when worn to the bottom of the central groove
Chapter 6 · Wheels and Tyres
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The word tread means the rubber on the crown and shoulders, whether it is smooth or moulded with a pattern. By far the most popular pattern today is the ribbed tread, with grooves running round the tyre. The grooves give the water somewhere to go, helping to prevent aquaplaning, and they improve the grip between the tread and the runway. You may still meet the diamond, or block, tread, known as the all-weather pattern. Nose wheel tyres, especially on aircraft with engines mounted on the rear fuselage, may have a chine, a lip moulded onto the shoulder that throws spray sideways and down, away from the engine intakes, to prevent flameouts from water ingestion. A single nose wheel has a chine on both sides. Finally, the Marstrand tyre has two contact ribs separated by a deep central groove. It behaves like twin wheels and resists shimmy, and it must be renewed when it is worn to the bottom of that central groove.
Part 3 · Tubes, tubeless, markings
Inner tubes and inflation valves Tubes are made by extruding hot rubber, butt-welding the ends, fitting a valve and vulcanising in a mould Near hot brakes the tube may have a thickened or cord-reinforced base ; replace like with like The valve stem is vulcanised to the tube: the valve cannot be renewed Schrader valve core = a non-return valve, but not a perfect seal So always fit the valve cap : it seals and keeps dirt out
Tubed tyre Valve
valve through the rim
inner tube
base may be standard, thickened or cord-reinforced near hot brakes
valve cap
Schrader core (non-return valve)
core is not a perfect seal: always fit the cap
modern spring: stainless steel
Chapter 6 · Wheels and Tyres
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Tubes are still found on light and older aircraft. A tube is made by forcing hot rubber through a circular die, cutting it to length, butt-welding the ends and fitting a valve, then inflating it in a mould and vulcanising it to its final shape. Because some brakes make a lot of heat close to the wheel rim, a tube may have a standard base, a thickened base or a cord-reinforced base, and a replacement must always be of the same type. The inflation valve stem is attached to a rubber base that is vulcanised to the tube, so the valve itself cannot be renewed. Inside the stem is a Schrader valve core, which works as a non-return valve, letting gas in but not out. The core is not considered a perfect seal, so a valve cap must always be fitted: it is the final seal, and it keeps dirt out of the valve. Older cores used brass springs; modern ones use stainless steel.
Part 3 · Tubes, tubeless, markings
Tubed versus tubeless tyres Tubed tyre Tubeless tyre Gas retained by a stretched inner tube an unstretched liner vulcanised inside the cover; bead wedged on a tapered seat Pressure loss tube is more permeable: loses pressure faster pressure maintained longer Puncture by a nail tube can deflate rapidly liner clings to the object : slow leak Impact and rough use tube can be pinched; runs hotter (tube rubs the casing) thicker casing, stress spread: more resistant Weight heavier about 7.5% lighter Creep excessive creep tears out the valve valve is in the wheel: no valve damage (creep still possible)
Tubeless tyres can still creep; they simply cannot shear their valve. They need a sealed, Bakelite-impregnated wheel with O-rings.
Chapter 6 · Wheels and Tyres
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most modern aircraft use tubeless tyres, and the table shows why. A tubeless tyre has an extra rubber liner vulcanised to the inside of the cover and under the beads, and the gas seal depends on the bead being wedged onto the taper of the rim. Because that liner is not stretched, it holds pressure for longer than a stretched tube, which is more permeable. If a nail goes in, the unstretched liner clings to it, so the tyre leaks slowly instead of going flat at once. The casing is thicker, and the liner spreads impact stresses, so a tubeless tyre is more resistant to impacts and rough treatment, while a tubed tyre runs hotter because the tube rubs inside the casing. Leaving out the tube saves about seven and a half per cent in weight. And because the valve is in the wheel, creep cannot tear it out. Be careful, though: a tubeless tyre can still creep round the rim; it simply has no valve to damage.
Part 3 · Tubes, tubeless, markings
The four tyre pressure categories Category Pressure (psi) Pressure (bar) Typical surface Low pressure 25 to 35 1.73 to 2.42 grass Medium pressure 35 to 70 2.42 to 4.83 grass, or medium-firm surfaces without a consolidated base High pressure 70 to 90 4.83 to 6.21 concrete runways Extra high pressure over 90 (some up to 350) over 6.21 (up to 24.2) concrete runways
Landing speed, weight, runway surface and gear design all decide the size, construction and pressure of a tyre.
Chapter 6 · Wheels and Tyres
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aircraft differ hugely in landing speed, weight, the surfaces they use and the way their gear is built, so tyres come in a wide range of sizes, constructions and pressures. They fall into four categories. Low-pressure tyres run at twenty-five to thirty-five pounds per square inch, about one point seven to two point four bar, and suit grass. Medium-pressure tyres run at thirty-five to seventy psi, up to about four point eight bar, on grass or on firm surfaces without a consolidated base. High-pressure tyres, seventy to ninety psi, up to about six point two bar, are for concrete runways. Extra-high-pressure tyres run above ninety psi, and some airliner tyres are inflated to around three hundred and fifty psi, which is about twenty-four bar. They also need concrete. Remember the link with the previous chapter: lower pressures and more wheels mean a lower load on the surface, which is why rough-field aircraft use big, soft tyres.
Part 3 · Tubes, tubeless, markings
Reading the sidewall Size : outside diameter × nominal width (and inside diameter), in inches or mmPly rating (e.g. 16PR) and speed rating : the maximum ground speed tested, in mph ECTA (or a symbol): extra carbon, electrically conducting for earthingGreen or grey dots : awl vents , letting gas trapped in the casing escapeRed dot or triangle : the light spot , fitted in line with the valve for balanceDRR / REINFORCED TREAD : a fabric layer in the tread that may show with wear
49 × 17 32 PR TUBELESS 225 MPH ECTA DRR
red dot = light spot fit it at the valve
green dots = awl vents
Size: outside diameter × width (and rim diameter)
PR: ply rating, an index of strength
Speed rating: max ground speed tested, in mph
ECTA: extra carbon, electrically conducting (earthing)
DRR / REINFORCED TREAD: fabric in the tread, may show
Chapter 6 · Wheels and Tyres
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
A tyre sidewall carries a lot of information. The size gives the outside diameter, the width and the rim diameter. The ply rating is shown as, for example, sixteen P R. The speed rating is the maximum ground speed, in miles per hour, to which the tyre has been tested and approved. The letters E C T A, or a special symbol, mean extra carbon has been added to make the rubber electrically conducting, so static can drain to earth. Green or grey dots mark the awl vents: small holes that let gas which has seeped from inside a tubeless tyre into the casing escape, so it cannot separate the plies when the outside pressure falls at altitude. A red dot or triangle marks the lightest part of the tyre, which is fitted next to the valve, the heaviest point, to help balance the wheel. D R R means a reinforced tread, whose fabric may show as it wears.
Part 4 · Pressure and creep
Rated pressure: the 4% and 10% rules Rated inflation pressure : set by the tyre manufacturer for a cold tyre not under load Weight on the wheel distorts the tyre: pressure rises 4% So when checking or inflating on the aircraft , add 4% to the rated pressure Taxying, take-off and landing heat the tyre: up to a further 10% Example: rated 200 psi → 208 psi cold on the aircraft → about 229 psi after a long taxi
200 psi Rated cold, unloaded 208 psi +4% loaded cold, on the aircraft 229 psi +10% hot after taxi / landing
200 × 1.04 = 208 psi (inflate to this on the aircraft)
208 × 1.10 ≈ 229 psi (normal hot reading)
Never bleed a hot tyre down to the cold figure:
it will be under-inflated once it cools
Chapter 6 · Wheels and Tyres
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every tyre has a rated inflation pressure, specified by the tyre manufacturer, and it applies to a cold tyre that is not under load, in other words a tyre not fitted to an aircraft. Once the tyre carries the weight of the aircraft, it distorts, its internal volume shrinks a little, and the pressure rises by about four per cent. So when you check or inflate a cold tyre on the aircraft, you mentally add four per cent to the rated pressure. Then, during taxying, take-off and landing, the tyre flexes and heats up, and its pressure can rise by up to a further ten per cent. Here is the worked example. Rated pressure two hundred psi; on the aircraft, cold, you should see two hundred and eight; after a long taxi it may read about two hundred and twenty-nine. That hot rise is normal: never let gas out of a hot tyre to bring it down to the cold figure, or it will be badly under-inflated when it cools.
Part 4 · Pressure and creep
Why heat raises the pressure A tyre is roughly a fixed volume , so absolute pressure rises in proportion to absolute temperature A gas temperature rise of only about 27 °C adds 10% to the pressure Use nitrogen or another inert gas with no more than 5% oxygen About 90% of tyre failures come from incorrect pressure Under-inflation : creep, overheating of the sidewalls, shoulder wear; over-inflation : crown wear, cuts, less gripModern aircraft can show tyre pressures on the systems display
180 200 220 240 260 280
0 20 40 60 80 100 120
rated 200 psi (cold, unloaded)
208 psi: cold, on the aircraft (+4%)
229 psi: hot after taxi (+10%)
gas temperature (°C)
gauge pressure (psi)
Chapter 6 · Wheels and Tyres
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a warm tyre read higher? A tyre is close to a fixed volume, so by the gas laws its absolute pressure rises in direct proportion to its absolute temperature. The graph starts at two hundred and eight psi, cold, on the aircraft at fifteen degrees. Because absolute temperature at fifteen degrees is already about two hundred and eighty-eight kelvin, a rise of only about thirty degrees in the gas is enough to add ten per cent to the pressure. Tyres must be kept at the correct pressure, using nitrogen or another inert gas containing no more than five per cent oxygen. This matters a great deal: about ninety per cent of all tyre failures are blamed on incorrect pressure. An under-inflated tyre flexes too much, overheats its sidewalls, wears its shoulders and tends to creep round the wheel. An over-inflated tyre wears its crown, cuts more easily and grips less. Many modern aircraft now show each tyre pressure on the electronic systems display.
Part 4 · Pressure and creep
Creep (slippage) Creep : the tyre slowly rotating round the wheel rim Normal on newly fitted tyres until they settle; most likely thenDetected by white creep marks on the tyre and the wheel getting out of line Limit: 1 in for tyres up to 24 in diameter, 1½ in above; then remove, inspect tube and valve, re-mark On a tubed tyre excessive creep tears out the valve and the tyre deflates or bursts Less of a problem with tubeless tyres; reduced by correct pressure
Marks aligned After creep
valve
creep
tyre mark over wheel mark
marks out of line tubed: valve dragged, can tear out and burst
Limit: 1 in (tyres up to 24 in diameter), 1½ in (over 24 in)
Chapter 6 · Wheels and Tyres
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Creep, or slippage, is the tyre slowly rotating round the wheel rim. When a tyre is first fitted it moves a little round the rim; at that stage this is normal, and it should stop once the tyre has settled. So creep is most likely on a newly fitted tyre. To detect it, matching white lines are painted across the tyre and the wheel rim; if they move out of line, the tyre has crept. The limits are one inch for tyres up to twenty-four inches outside diameter, and one and a half inches for larger tyres. Beyond that the tyre must be removed, the tube checked for tearing at the valve and the valve stem for deformation, and if all is well the tyre is refitted and the marks re-applied. Creep matters most with a tube, because the valve is part of the tube: as the tyre and tube creep, the valve is dragged sideways until it tears out. Correct pressure is the best prevention.
Part 5 · On the runway
Aquaplaning A wedge of water builds under the tread and breaks its contact with the runway Dynamic : standing water deeper than the tread depth, above the critical speed VP Viscous : a thin film on a smooth or rubber-coated surface, possible at low speedReverted rubber : a locked wheel boils the water to steam and melts the rubberBraking friction falls to almost zero ; directional control is lost Risk grows as tread depth falls : tread must be assessed accurately
direction of roll
water wedge
tyre lifted off the runway
Dynamic: standing water deeper than the tread; above Vp
Viscous: thin film on a smooth or rubber-coated surface
Reverted rubber: locked wheel boils the water; steam
Friction coefficient falls to almost zero
Chapter 6 · Wheels and Tyres
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aquaplaning, also called hydroplaning, happens when a wedge of water builds up in front of and under the tyre and lifts the tread off the runway. Watch the drawing: as the tyre rolls into standing water, the water cannot escape fast enough, its pressure rises, and above a critical speed it supports the tyre completely. That is dynamic aquaplaning, and it needs water deeper than the tread grooves. Viscous aquaplaning can happen at much lower speeds on a thin film of water over a very smooth or rubber-coated surface. Reverted rubber aquaplaning starts with a locked wheel: friction heat boils the water into steam, which melts the rubber and lifts the tyre. In all cases the friction coefficient falls to almost zero, so the brakes do nothing, the wheels may lock and skid, and directional control is lost. The less tread there is, the sooner it happens, so tread depth must be assessed carefully.
Part 5 · On the runway
Calculating the aquaplaning speed
20 40 60 80 100 120 140 160
0 50 100 150 200 250
225 psi: 135.0 kt 150 psi: 110.2 kt 150 psi: 94.3 kt
Vp = 9 √P (rotating: take-off)
Vp = 7.7 √P (non-rotating: touchdown)
tyre pressure P (psi)
Vp (knots)
P in kg/cm²: Vp = 34 √P
Vp in knots. On slush or wet snow, divide P by the contaminant's specific gravity first: Vp = 9 √(P ÷ SG). Lower SG means a higher Vp.
Chapter 6 · Wheels and Tyres
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The minimum speed for dynamic aquaplaning, V P, depends mainly on tyre pressure. The rule you must know is V P equals nine times the square root of the tyre pressure, with the pressure in pounds per square inch and the answer in knots. If the pressure is in kilograms per square centimetre, use thirty-four times the square root instead. Worked example: a tyre at two hundred and twenty-five psi. The square root of two hundred and twenty-five is fifteen, times nine is one hundred and thirty-five knots. Some questions go further. The factor nine applies to a tyre that is already rotating, as on the take-off run. A tyre that is not rotating, at the moment of touchdown, aquaplanes at a lower speed, about seven point seven times root P. So for one hundred and fifty psi: about one hundred and ten knots on take-off, but only about ninety-four knots at touchdown. On slush or wet snow, divide the pressure by the specific gravity before taking the root.
Part 5 · On the runway
Damage, wear limits and care Cuts reaching the cords: tyre unserviceable until repairedBulges : possible casing failure; fractured fabric means renew the cover Stones, metal, glass : remove and probe the cut with a blunt tool Wear limit : patterned tread worn to the base of the marker grooves (or tie bars) over 25% of the circumference ; plain tread to the casing fabricA worn tyre with a sound casing can be retreaded (remoulded) Protect from heat, damp, sunlight , oil, fuel, glycol and hydraulic fluid : cover it, wipe spills at once
Tread wear markers
new: marker groove visible
worn to the marker base: remove (or retread)
Keep away from the tyre
Oil Fuel Glycol Hydraulic fluid Heat Sunlight Damp Ozone
Chapter 6 · Wheels and Tyres
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Tyres are inspected for cuts, bulges, embedded objects, wear, creep and soft, spongy patches. A cut that reaches the cords makes the tyre unserviceable until it is repaired. A bulge may mean the casing has partly failed; if the fabric is fractured, the cover must be renewed. Embedded stones or glass are removed and the hole probed with a blunt tool. For wear, a patterned tread may be used until it is worn to the base of the marker grooves, or the marker tie bars, over a quarter of the circumference; a block pattern is finished when its pattern is only just visible at the most worn point; a plain tread may be worn to the casing fabric but no further. A worn tyre whose casing is sound is not scrap: it can be repaired by retreading. Rubber is attacked by heat, damp, bright sunlight, ozone, oil, fuel, glycol and hydraulic fluid, so cover the tyres when parked or when fluids are being drained, and wipe off any spill immediately.
Part 5 · On the runway
Making tyres last Over-inflation : excessive wear of the crown ; under-inflation : excessive wear of the shoulders Taxi at no more than about 25 mph (40 km/h, ≈ 22 kt) Tight turns scrub the tread (scuff marks): use the largest turning radius , never tighter than the minimum Roll straight for a short distance before stopping Avoid locking the wheels : a skid leaves a flat spot
Correct pressure even wear across the tread Over-inflated crown (centre) wears fastest Under-inflated both shoulders wear fastest Locked-wheel skid flat spot, may expose cords
flat spot
Chapter 6 · Wheels and Tyres
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
How a tyre wears tells you how it has been treated. Too much pressure makes the tyre bulge at the crown, so the centre of the tread wears fastest. Too little pressure lets the tyre sag, so it rides on its shoulders and they wear fastest. The recommendation is to taxi at no more than about twenty-five miles per hour, which is forty kilometres per hour, or roughly twenty-two knots. Tight turns are particularly hard on multi-wheel units: the tread is dragged sideways and scrubbed, leaving scuff marks, and in the worst case the tread tears to expose the casing. So use the largest turning circle you can, never turn tighter than the minimum radius, including during push-back, and roll straight for a short distance before you stop, so the tyres are not left twisted. Finally, never lock a wheel: a skid grinds a flat spot into the tread in a fraction of a second.
Part 5 · On the runway
Tyre speed limits and performance The speed rating is the maximum ground speed the tyre is approved for Ground speed at lift-off rises with pressure altitude , temperature and a tailwind The tyre limit therefore caps the lift-off speed , and so VR and V1 With increased V2 techniques, check the tyre speed limit : mass may have to be reduced (MAT limits ) Wheel, tyre and brake energy limits also set VMBE (brake design: next chapter)
Ground speed at lift-off versus a 225 mph tyre
tyre limit 225 mph
Sea level ISA, calm 178 mph Hot and high ISA+30, 5000 ft 199 mph + tailwind 10 kt tail 225 mph
TAS rises with altitude and temperature; a tailwind adds to it
If the limit is reached: reduce the take-off mass
Chapter 6 · Wheels and Tyres
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every tyre has a speed rating: the maximum ground speed, in miles per hour, to which it has been tested and approved. The aircraft lifts off at an indicated airspeed, but the tyre feels the ground speed. At a high airfield, on a hot day, the true airspeed for the same indicated speed is higher, and a tailwind adds to it again, so the ground speed at lift-off can approach the tyre limit, as the bars show. The tyre speed limit therefore caps the lift-off speed, and with it the rotation speed and V one, so tyre design really does affect the take-off speeds. When an operator uses an increased V two technique to improve climb performance, the higher lift-off speed must still stay below the tyre limit, and sometimes the take-off mass has to be reduced to satisfy it; these are known as MAT limits. The brakes, as we will see, also set a limit: the maximum brake energy speed.
Summary
Wheels and tyres: what to take into the exam Wheels Loose flange (ring), detachable (bolts), divided (two halves + seal). Al or Mg alloy; tubeless: Bakelite, O-rings.
Fusible plugs Melt on temperature : red 155, green 177, amber 199 °C. Controlled deflation, not burst.
Construction Tread, breakers, casing plies, bead wires, apex, chafer. Ply rating = strength index (32 PR, 18 plies).
Tubeless Holds pressure longer, slow leaks, tougher, ~7.5% lighter , no valve tear-out. Can still creep.
Markings ECTA conducting; green/grey dots: awl vents ; red dot: light spot by the valve; speed in mph.
Pressure Rated = cold, unloaded. +4% on the aircraft, up to +10% hot. Nitrogen ≤5% O₂. 90% of failures.
Creep Normal when new . White marks. 1 in (≤24 in) / 1½ in. Tubed : valve tears out.
Runway Vp = 9√P kt (7.7√P touchdown; 34√P kg/cm²). Crown wear: over; shoulders: under. Taxi ≤ 25 mph.
Chapter 6 · Wheels and Tyres
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the chapter on one page. Wheels have a loose flange held by a ring, a detachable flange held by bolts, or two bolted halves with a seal; they are aluminium or magnesium alloy, and tubeless wheels are Bakelite sealed with O-rings. Fusible plugs melt at a temperature, red one fifty-five, green one seventy-seven, amber one ninety-nine, giving controlled deflation. A tyre is tread, breakers, casing plies and beads, and the ply rating is a strength index, not a ply count. Tubeless tyres hold pressure longer, leak slowly, are about seven and a half per cent lighter and cannot tear out their valve, but they can still creep. Green or grey dots are awl vents, and the red dot is the light spot, fitted by the valve. Rated pressure is cold and unloaded: add four per cent on the aircraft, and expect up to ten per cent more when hot. And the aquaplaning speed is nine root P knots.