Electrics · Chapter 10
Introduction to AC Why aircraft use alternating current, how a sine wave is made and measured, and what inductance, capacitance, impedance, power factor and three phases do to it.
A B C 115 V · 200 V · 400 Hz three phases, 120° apart © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter ten opens the AC half of the course. Almost every large aircraft generates alternating current, at one hundred and fifteen and two hundred volts and four hundred hertz, in three phases. In this lesson we build the ideas you need for everything that follows: how a turning magnet or coil makes a sine wave, how we describe it with frequency, peak and r.m.s. values, how inductance and capacitance push the current out of step with the voltage, why only part of the power we supply does useful work, and how three phases are combined into the supply you will meet on every airliner.
Chapter 10 roadmap
From a turning loop to the three-phase supply 1 · The sine wave Why AC, how a generator makes it, and the terms: cycle, phase, frequency , period, peak and r.m.s.
2 · Frequency from the machine Poles and rpm set the frequency: f = (poles ÷ 2) × (rpm ÷ 60) , so 8 poles at 6000 rpm give 400 Hz.
3 · R, L and C Resistance keeps V and I in phase; inductance makes I lag, capacitance makes I lead. CIVIL .
4 · Reactance and impedance XL = 2πfL rises with frequency, XC = 1/2πfC falls. Z is their vector sum with R. Resonance.
5 · AC power True power (W), reactive power (VAR), apparent power (VA) and the power factor = kW ÷ kVA.
6 · Three phases Three windings 120° apart; star gives 115 V phase and 200 V line ; delta has no neutral.
Chapter 10 · Introduction to AC
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this chapter. First we look at why big aircraft use AC at all, and how a coil turning in a magnetic field produces a sine wave, with the words used to describe it: cycle, phase, frequency, period, peak and r.m.s. Then we see how the number of poles and the speed of a generator fix its frequency. Next come the three kinds of opposition to current: resistance, inductance and capacitance, and how inductance and capacitance push the current out of step with the voltage. That leads to reactance and impedance, and to resonance. Then we look at power in AC circuits: true power, reactive power, apparent power and the power factor. Finally we put three windings together to make the three-phase supply, and learn why one phase gives one hundred and fifteen volts but two lines give two hundred.
Part 1 · Why AC?
Why large aircraft use alternating current AC generators are simpler and more robust than DC machines, with a better power-to-weight ratio Transformers step the voltage up or down with almost 100% efficiency TRUs (transformer rectifier units) give any DC voltage, e.g. 28 V DC , simplyThree-phase motors on a constant-frequency supply are simpler, more robust and more efficient than DC motorsNo commutator : no commutation and brush-arcing problems, especially at high altitude Higher voltage means less current for the same power, so lighter cables AC generator no commutator AC bus 115/200 V 400 Hz Transformer any voltage, almost 100% efficient TRU transformer rectifier unit: 28 V DC Three-phase motors simple, robust, efficient Light cables high voltage, low current better power-to-weight no brush arcing at height
Chapter 10 · Introduction to AC
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Small aircraft manage nicely on twenty-eight volts DC, but as aircraft grew and their electrical loads grew with them, alternating current took over. Here is why. AC generators are simpler and more robust than DC machines, and they give more power for each kilogram. With AC you can use a transformer to raise or lower the voltage with almost one hundred per cent efficiency, and a transformer rectifier unit, a T R U, turns AC into whatever DC you need, typically twenty-eight volts for the DC buses. Three-phase AC motors running on a constant frequency are simpler, tougher and more efficient than DC motors. AC machines have no commutator, so there are no commutation problems and much less brush arcing, which matters at high altitude where arcing gets worse. And because the voltage is high, the same power needs less current, so the cables can be thinner and lighter. That last point alone saves a lot of weight in a big airliner.
Part 1 · Making AC
A loop turning in a magnetic field A loop of wire (the armature) turns between a north and a south pole The flux through it changes continuously, so an e.m.f. is induced as long as it turns Size of the e.m.f. depends on speed of rotation and field strength (rate of change of flux) Slip rings and carbon brushes connect the turning loop to the load, keeping the output ACEach half turn the polarity reverses : current flows back and forth about a mean position N S 0 rotating loop slip rings brushes field centre-zero voltmeter
Chapter 10 · Introduction to AC
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is the simplest AC generator. A single loop of wire, the armature, turns between a north pole and a south pole, and the magnetic field runs across from north to south. As the loop turns, the amount of flux passing through it changes all the time, so an e.m.f. is induced in it for as long as it keeps turning. The faster it turns, and the stronger the field, the faster the flux changes and the bigger the e.m.f. Each end of the loop is joined to its own slip ring, and carbon brushes rubbing on the rings connect it to the outside circuit. Because slip rings simply pass on whatever the loop produces, the output stays alternating. Watch the centre-zero voltmeter: its needle swings one way, back through zero and the other way, twice in every turn of the loop. Current that flows backwards and forwards about a mean position like this is alternating current.
Part 1 · Making AC
One revolution makes one cycle of a sine wave 1 · 0° 2 · 90° 3 · 180° 4 · 270° 5 · 360° + maximum: sides cut the field at right angles − maximum: polarity reversed zero θ e.m.f. e = Emax sin θ e.m.f. = maximum × sine of the angle turned: at 30° it is half the maximum, at 90° it is the maximum. Direction in each side: Fleming's right-hand rule .
Chapter 10 · Introduction to AC
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow one complete turn of the loop, seen end on, with the red dot marking one side. In position one the two sides are moving along the field, parallel to it. They cut no lines of flux, so the e.m.f. is zero. A quarter of a turn later, in position two, the sides are moving straight across the field, at right angles to it, so the rate of cutting and the e.m.f. are at their maximum. At position three the sides again move along the field and the e.m.f. falls to zero. Then each side moves across the field in the opposite direction, so in position four the e.m.f. is at its maximum again, but with reversed polarity. Position five brings us back to the start. Plot it and you get a sine wave: the e.m.f. at any instant equals the maximum value times the sine of the angle turned. So at thirty degrees it is half the maximum. Fleming's right-hand rule gives the direction in each side.
Part 1 · Describing AC
Cycle, phase, frequency and period Cycle : one complete series of values, positive and negativePhase : position within the cycle in degrees; one cycle = 0° to 360° Frequency f: cycles per second, in hertz (1 Hz = 1 cycle per second)Constant-frequency aircraft supplies are normally 400 Hz Period T: time for one cycle, T = 1/f ; at 400 Hz, T = 2.5 msAmplitude (peak): the maximum value reached in a cyclefrequency f frequency 2f: half the period one cycle = 360° · period T = 1/f amplitude 90° 180° 270° T/2 same time span, twice the cycles
Chapter 10 · Introduction to AC
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A few words describe any alternating wave. A cycle is one complete set of values, up through the positive half and down through the negative half, back to the start. We give positions in the cycle as angles, called phase, so one cycle runs from zero to three hundred and sixty degrees. Frequency is the number of cycles every second, measured in hertz, and one hertz is one cycle per second. Aircraft constant-frequency systems run at four hundred hertz, much higher than mains frequency, because at four hundred hertz transformers and motors can be smaller and lighter. The period is the time one cycle takes, so it is one divided by the frequency. At four hundred hertz the period is one four-hundredth of a second, two point five milliseconds. The amplitude, or peak value, is the largest value reached in the cycle. In the lower wave, two cycles fit in the same time, so the frequency is double and the period half.
Part 1 · Frequency
Poles and speed set the frequency One cycle for each pair of poles that passes a stator coil f = (number of poles ÷ 2) × (rpm ÷ 60) , in hertzWorked: 8 poles at 6000 rpm : 4 × 100 = 400 Hz Same 8 poles at 4500 rpm: 4 × 75 = 300 Hz: slower drive, lower frequency To lower a generator's frequency, reduce its rotational speed ; the field current changes voltage, not frequency N S N S stator coil 4 poles = 2 pole pairs 2 cycles per turn
Chapter 10 · Introduction to AC
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
This rotor has four poles: the red bar has a north pole at each end and the blue bar a south pole at each end, so going round we meet north, south, north, south. Each time a north pole and then a south pole pass the stator coil, the coil goes through one complete cycle. A two-pole rotor therefore gives one cycle per turn, and this four-pole rotor gives two. So the frequency is the number of pole pairs times the revolutions per second, which is the number of poles divided by two, times the r p m divided by sixty. Take the classic case: eight poles at six thousand r p m. That is four pole pairs times one hundred revolutions per second, four hundred hertz. Remember: frequency depends only on poles and the speed of the shaft. Changing the field current changes the voltage, not the frequency.
Part 1 · Measuring AC
Peak, peak to peak, average and r.m.s. peak peak to peak r.m.s. 0.707 average 0.637 (½ cycle) Worked: an aircraft 115 V phase r.m.s. (what meters read) 115 V peak = 115 × 1.414 162.6 V peak to peak = 2 × peak 325 V average over ½ cycle = 0.637 × peak 103.6 V r.m.s. = peak × 0.707 162.6 × 0.707 = 115 r.m.s. = peak ÷ √2 = 0.707 × peak ; peak = 1.414 × r.m.s. Supply values, voltmeters and ammeters are quoted in r.m.s.
Chapter 10 · Introduction to AC
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are several ways to put a single number on a wave that never stands still. The peak, or amplitude, is the highest value. Peak to peak is from the top of the positive half to the bottom of the negative half, twice the peak. The average over a whole cycle is zero, because the halves cancel, so an average is taken over one half cycle; for a sine wave it is zero point six three seven of the peak. The most useful number is the r.m.s. value, zero point seven zero seven of the peak, or the peak divided by root two. Aircraft supply values, and the readings on AC voltmeters and ammeters, are r.m.s. values. Look at the worked box. Our one hundred and fifteen volt phase is one hundred and fifteen volts r.m.s. Its peak is one point four one four times that, about one hundred and sixty-three volts, and peak to peak about three hundred and twenty-five volts.
Part 1 · Measuring AC
Why r.m.s.? Equal heating r.m.s. = the DC value that gives the same heating in a resistance Heating depends on current squared , which is always positive Square many instantaneous values, take the mean , then the square root : root mean square For a sine, mean of i² = ½ peak², so r.m.s. = peak × √½ = 0.707 × peak 1 A DC heats a resistor more than AC of 1 A peak; AC needs 1.414 A peak to match current i (peak 1 A) i² (heating): always positive mean of i² = ½ √(mean of squares) = √½ = 0.707 A: the same heat as 0.707 A DC
Chapter 10 · Introduction to AC
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why do we use this strange r.m.s. value? Because it tells us what the AC will actually do. The r.m.s. value of an alternating current is the steady DC current that would produce the same heat in the same resistor. Heat depends on the current squared, and squaring makes every value positive, as the lower curve shows. Its mean, over a cycle, is exactly half the peak squared. Take the square root of that mean and you have the root of the mean of the squares, the r.m.s. value: the peak times the square root of a half, zero point seven zero seven. So one amp of DC makes a resistor hotter than an AC with a peak of one amp; to match it, the AC needs a peak of one point four one four amps. Zero point seven zero seven is also the sine of forty-five degrees, a handy memory aid, but the real reason is the equal heating.
Part 1 · Phase
Phase difference: leading and lagging Two waves of the same frequency need not pass through zero together The gap between corresponding points is the phase difference or phase angle The wave that reaches its peak first leads ; the other lags In AC circuits, V and I always have the same frequency and the same wave shape Only a purely resistive circuit keeps them in phase ; L and C shift them 60° A B B reaches each point 60° after A: B lags A by 60° (A leads B by 60°) same frequency, different timing
Chapter 10 · Introduction to AC
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now an idea that runs through the rest of the chapter: phase difference. Two waves can have exactly the same frequency and yet not pass through zero, or reach their peaks, at the same moment. The time gap between corresponding points, measured in degrees, is the phase difference, or phase angle. In the drawing, wave B reaches every point sixty degrees after wave A. We say B lags A by sixty degrees, or, the same thing, A leads B by sixty degrees. In an AC circuit, the current always has the same frequency as the voltage, and if the voltage is a sine wave the current is a sine wave too. What can change is the timing between them. Only in a purely resistive circuit do they stay in step. Inductance and capacitance, which we meet next, shift the current out of phase with the voltage, and that has big effects on power.
Part 2 · R, L and C
Pure resistance: V and I in phase Strictly no resistance is "pure": every wire has some inductance; we assume it here Voltage and current reach zero and their peaks together : in phase Ohm's law works as in DC, using r.m.s. values: I = V ÷ RWorked: 115 V across 23 Ω: I = 5 A r.m.s. , power 575 W Heaters, lamp filaments and de-icing mats behave almost purely resistively 115 V 23 Ω I = 115 ÷ 23 = 5 A r.m.s. V I in phase: zero and peaks together
Chapter 10 · Introduction to AC
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at the three basic kinds of circuit one at a time, starting with pure resistance. Strictly there is no such thing in AC, because every resistor and even a plain wire has a little inductance, but for heaters and lamp filaments it is a very good approximation. In a pure resistance, the current rises and falls exactly with the voltage. They pass through zero together and reach their peaks together, so we say they are in phase. That makes life simple: Ohm's law works exactly as it does in DC, as long as you use r.m.s. values. Here, one hundred and fifteen volts across twenty-three ohms drives five amps r.m.s., and the power is one hundred and fifteen times five, five hundred and seventy-five watts. Resistive loads also do not care about frequency, which is why electrical de-icing heater mats can run happily on a supply whose frequency wanders.
Part 2 · Inductance
Mutual induction: a changing field induces a voltage a. Switch open no current, no field: meter at zero b. Switch just closed field grows: meter kicks one way c. Switch opened field collapses: kick the other way d. AC in the primary field always changing: meter swings A voltage is induced only while the field is changing ; with AC it changes all the time. The induced voltage grows with the rate of change , so with frequency. This is how a transformer works.
Chapter 10 · Introduction to AC
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
A voltage can be induced without anything moving, just by changing a current. Look at the four panels. In panel a, a primary coil sits next to a secondary coil with a centre-zero meter, but the switch is open, so nothing happens. In panel b the switch has just closed. The current builds up, its magnetic field expands and cuts the secondary coil, and the meter kicks. Once the current is steady the field stops changing and the meter returns to zero. In panel c the switch has opened, the field collapses, and the meter kicks the other way. Now feed the primary with AC, as in panel d. The field is always changing, so a voltage is induced in the secondary all the time and the meter swings to and fro. This is mutual induction, the principle of the transformer. The induced voltage is biggest when the current is changing fastest, which is as it passes through zero, and it grows with the frequency.
Part 2 · Inductance
Self-induction: the coil fights the change A coil's own changing field induces a back e.m.f. in itself: self-induction Lenz's law : the back e.m.f. opposes the change of currentMore back e.m.f. with more turns , a soft-iron core , or a higher frequency Inductance L , unit the henry (H); usually mH or μH 1 H: a change of 1 A per second induces 1 V of back e.m.f. In DC, inductance opposes current only while switching on and off 115 V soft-iron core coil (inductor, L) lamp more turns → more back e.m.f.: lamp dimmer iron core inserted → more back e.m.f.: lamp dimmer higher frequency → more back e.m.f.: lamp dimmer
Chapter 10 · Introduction to AC
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Take away the secondary coil. The changing field of the coil still cuts its own turns, so it induces a voltage in itself. That is self-induction, and by Lenz's law the induced voltage always opposes the change of current that causes it, so we call it the back e.m.f. Watch the scene. The AC supply drives current through the coil and the lamp. Now the soft-iron core slides into the coil. The field becomes much stronger, the back e.m.f. grows, and the lamp gets dimmer because less current flows. Next, the supply frequency is doubled. The current now changes twice as fast, the back e.m.f. is bigger still, and the lamp is dimmer again. A coil's ability to make back e.m.f. is its inductance, symbol L, measured in henries. One henry gives one volt of back e.m.f. when the current changes at one amp per second. In a DC circuit, inductance opposes the current only at switch-on and switch-off.
Part 2 · Inductance
In pure inductance the current lags by 90° The back e.m.f. holds back the rise of current: current lags voltage In a purely inductive circuit the lag is exactly 90° Practical coils have resistance too, so the lag is between 0° and 90° A circuit that is mainly inductive : current lags (motors, transformers, solenoids) Phasor diagrams: arrows turning anticlockwise ; V usually drawn as the reference 90° V I V (reference) I lags by 90° Phasors turn anticlockwise: I is 90° behind V
Chapter 10 · Introduction to AC
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the coil fights every change, the current cannot keep up with the voltage. The voltage rises, but the current is held back by the back e.m.f., and it reaches its peak later. In a circuit containing only inductance, the current lags the voltage by exactly ninety degrees: look at the waves, the current peak comes a quarter of a cycle after the voltage peak. Real coils always have some resistance as well, so in practice the current lags by something between zero and ninety degrees, but the rule is the same. A circuit that is mainly inductive, with motors, transformers and solenoids, has its current lagging the voltage. Below the waves is a phasor diagram, a quicker way of showing the same thing. Each quantity is an arrow, and the arrows are imagined turning anticlockwise at the supply frequency. The voltage is drawn as the reference, pointing right, and the current is drawn ninety degrees behind it.
Part 2 · Inductive reactance
Inductive reactance: XL = 2πfL Opposition of an inductor to AC: inductive reactance XL , in ohms XL = 2πfL : proportional to frequency and to inductanceFrequency up : XL up, current down Frequency down : XL down, current up : inductive devices can overheat Worked: 10 mH at 400 Hz: XL = 2π × 400 × 0.01 = 25.1 Ω ; at 50 Hz only 3.14 Ω 0 200 400 600 800 0 20 40 60 400 Hz: 25.1 Ω 50 Hz: 3.14 Ω frequency (Hz) XL (Ω) L = 10 mH at 115 V: 4.6 A at 400 Hz, but 36.6 A at 50 Hz
Chapter 10 · Introduction to AC
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The opposition that an inductor offers to AC is called inductive reactance, X L, and it is measured in ohms like resistance. It is called reactance because it depends on frequency as well as inductance. The formula is X L equals two pi f L. So X L is proportional to frequency: double the frequency and you double the reactance, and the current falls. The more important direction for the exam is the other one. If the frequency falls, X L falls, and the current through an inductive device rises. Take a ten millihenry coil designed for four hundred hertz. Its reactance is two pi times four hundred times zero point zero one, about twenty-five ohms, so on one hundred and fifteen volts it takes about four point six amps. Run it at fifty hertz and the reactance drops to about three ohms and the current to over thirty-six amps. That is why an alternator running below its normal frequency makes motors and transformers overheat.
Part 2 · Capacitance
The capacitor: two plates and a dielectric Two conducting plates separated by an insulating dielectric (air, mica, waxed paper) Charge stored depends on plate area , distance between plates and the dielectric On DC it charges until its voltage equals the supply, then current stops It holds the charge (apart from leakage) and discharges in the opposite direction No electrons cross the dielectricUnit: the farad (F): 1 A for 1 s gives 1 V; in practice μF and pF dielectric + − + − + − + − + − two plates battery load charge discharge discharge current flows the opposite way to the charging current more charge with: larger plates plates closer better dielectric
Chapter 10 · Introduction to AC
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Capacitance is the ability to store electric charge, and the component that provides it is the capacitor: two conducting plates separated by an insulator called the dielectric, which can be air, mica or waxed paper, among others. Three things decide how much charge it can hold: the area of the plates, the distance between them, and the dielectric material. Connect it to a battery and electrons are pulled off one plate and pushed onto the other. Current flows until the capacitor's voltage equals the battery voltage, and then it stops. Disconnect it and it keeps its charge, like an accumulator keeps pressure, apart from a little leakage. Switch it across a load and it discharges, with the current flowing the opposite way to the charging current. Notice that no electrons ever pass through the dielectric. The unit of capacitance is the farad: one amp flowing for one second charges a one farad capacitor to one volt. That is huge, so we use microfarads and picofarads.
Part 2 · Capacitive reactance
On AC the capacitor passes current, leading by 90° On AC the capacitor charges and discharges every half cycle, so current keeps flowing in the circuit In a purely capacitive circuit the current leads the voltage by 90° XC = 1 ÷ 2πfC , in ohmsFrequency up : XC down , current up ; frequency down: current down Worked: 10 μF at 400 Hz: XC = 39.8 Ω ; at 800 Hz, 19.9 Ω capacitor lamp 400 Hz: 39.8 Ω 800 Hz: 19.9 Ω frequency (Hz) → XC (Ω), C = 10 μF
Chapter 10 · Introduction to AC
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Put a capacitor in an AC circuit and something surprising happens: the lamp lights. No electrons cross the dielectric between the plates, but the capacitor charges one way, discharges, and charges the other way every half cycle, so current flows backwards and forwards in the wires. The current is greatest when the voltage is changing fastest, which is as the voltage passes through zero, so in a purely capacitive circuit the current leads the voltage by ninety degrees. The opposition is called capacitive reactance, X C, equal to one over two pi f C. It behaves the opposite way to X L. Now watch: we raise the supply frequency from four hundred to eight hundred hertz. The capacitor charges and discharges twice as often, its reactance halves, more current flows, and the lamp gets brighter. For a ten microfarad capacitor, X C is about forty ohms at four hundred hertz and about twenty at eight hundred. So in a capacitive circuit, if the frequency increases, the current increases.
Part 2 · Summary of R, L and C
CIVIL, and reactance against frequency Capacitive: I leads V by 90° V I C I V I L in C, I leads V V leads I in L L and C are 180° apart: their reactances subtract resonance where XL = XC Reactance against frequency f₀ XL rises XC falls f → C : I leads V · V leads I in L . XL ∝ f; XC ∝ 1/f. Frequency down: inductive current up, capacitive current down.
Chapter 10 · Introduction to AC
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the summary of R, L and C on one page. The left graph shows a capacitive circuit, with the current leading the voltage by ninety degrees. To remember which way round the two reactive circuits go, use the word CIVIL. Read it from the left: in C, a capacitor, I, the current, leads V, the voltage. Read on: V, the voltage, leads I, the current, in L, an inductor. Because one leads by ninety degrees and the other lags by ninety, their effects are one hundred and eighty degrees apart, so inductive and capacitive reactance cancel each other, and we subtract one from the other. On the right is how each reactance varies with frequency. X L rises in a straight line, X C falls along a curve. Where they cross, they are equal, and that frequency is called the resonant frequency. Keep this picture in mind for any question that changes the frequency and asks what happens to the current.
Part 2 · Impedance
Impedance: the total opposition Impedance Z : total opposition to AC, in ohms Net reactance X = XL − XC (they act 180° apart) R and X are 90° apart, so add as vectors : Z = √(R² + X²) Worked: R 30 Ω, XL 60 Ω, XC 20 Ω: X = 40 Ω, Z = 50 Ω At 100 V: I = 2 A ; phase angle 53.1°, current lagging R = 30 Ω X = XL − XC = 60 − 20 = 40 Ω Z = 50 Ω φ = 53.1° Z = √(R² + X²) = √(30² + 40²) = 50 Ω At 100 V: I = 100 ÷ 50 = 2 A cos φ = R ÷ Z = 0.6 (current lags: net inductive)
Chapter 10 · Introduction to AC
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a real circuit we have resistance, inductive reactance and capacitive reactance together, and the total opposition to current is the impedance, Z, again in ohms. You cannot simply add the three, because each one shifts the current differently. First, combine the two reactances: they act in opposite directions, so the net reactance is X L minus X C. Then combine that with the resistance. Resistance and reactance are ninety degrees apart, so they add like the two sides of a right-angled triangle, the impedance triangle, and Pythagoras gives Z as the square root of R squared plus X squared. Let us try it. R is thirty ohms, X L sixty and X C twenty. The net reactance is forty ohms, inductive. Thirty squared plus forty squared is two thousand five hundred, so Z is fifty ohms. On one hundred volts, the current is two amps, and it lags the voltage by the angle in the triangle, about fifty-three degrees. So impedance is the vector sum of resistance and reactance.
Part 2 · Resonance
Resonance: when XL equals XC Frequency up: XL rises, XC falls, so at one frequency they are equal Then the circuit is resonant : f₀ = 1 ÷ (2π√LC) L and C in series : reactances cancel, current is maximum , limited only by R L and C in parallel : the line current is minimum Worked: 10 mH with 15.8 μF resonates at about 400 Hz L and C in series f₀ ≈ 400 Hz current MAXIMUM at f₀ I f → L and C in parallel f₀ ≈ 400 Hz line current MINIMUM at f₀ I f →
Chapter 10 · Introduction to AC
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Changing the frequency has opposite effects on an inductor and a capacitor. As frequency rises, X L goes up and X C goes down, so for any given coil and capacitor there must be one frequency at which the two are equal. At that frequency the circuit is said to be resonant. In this example a ten millihenry coil and a fifteen point eight microfarad capacitor are resonant at about four hundred hertz. What happens then depends on how they are connected. With L and C in series, their reactances cancel completely, the only opposition left is the resistance, and the current is at its maximum, the sharp peak in the upper graph. With L and C in parallel, the coil and capacitor pass energy back and forth between themselves, and the current drawn from the supply line is at its minimum, the dip in the lower graph. Resonant circuits are the basis of radio tuning and of filters. For the exam: series resonance, current maximum; parallel resonance, current minimum.
Part 3 · AC power
Power in a pure resistance: always positive voltage v current i power p = v × i average power Pure resistance φ = 0°: v and i in phase p is always positive p has twice the frequency average power (green) = ½ of peak power = V r.m.s. × I r.m.s. true power, in watts Instantaneous power p = v × i. Average power = V r.m.s. × I r.m.s. = true power (real, wattful power) in watts or kW.
Chapter 10 · Introduction to AC
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now to power. In DC, power is simply volts times amps. In AC we multiply the instantaneous values of voltage and current, moment by moment, to get the instantaneous power, the purple curve. In a pure resistance, voltage and current are in phase. When the voltage is positive, so is the current, and when the voltage is negative, so is the current, so their product is always positive: the resistance takes energy from the supply all the time and turns it into heat. Notice too that the power curve goes through two humps for every cycle of the supply, so it has twice the frequency. The average power is the line halfway between the minimum and maximum of the power curve, the green line. It works out to the r.m.s. voltage times the r.m.s. current. This positive, useful power is called the true power, also real power or wattful power, measured in watts or kilowatts.
Part 3 · AC power
Power in pure inductance or capacitance: zero on average voltage v current i power p = v × i average power Pure inductance φ = 90°: i lags v p: equal + and − loops + : energy into the field − : energy given back average power = 0 W V × I is all reactive: VAR (kVAR) Same with pure capacitance (I leads by 90°). V × I that does no net work = reactive power , in VAR or kVAR . V r.m.s. × I r.m.s. = apparent power , in VA or kVA.
Chapter 10 · Introduction to AC
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now make the circuit purely inductive, with the current lagging by ninety degrees. Multiply voltage and current again and the power curve, still at twice the frequency, now sits evenly about the axis. During the positive loops the supply pushes energy into the coil to build its magnetic field. During the negative loops the field collapses and the coil gives exactly the same energy back, generating the back e.m.f. The positive and negative loops are equal, so the average, the true power, is zero. The supply still has to deliver current though, so the cables and the generator still carry it and still heat up. The volts times amps that do no net work are called reactive power, measured in volt-amps reactive, VAR or kVAR. A pure capacitor behaves the same way, with the current leading instead of lagging. And the plain product of r.m.s. volts and r.m.s. amps, whatever the phase, is called the apparent power, measured in volt-amps, VA or kVA.
Part 3 · AC power
A practical circuit: true, reactive and apparent power Real loads have R and L (and sometimes C): the phase angle lies between 0° and 90° With R = XL the angle is 45° : positive and negative power loops are unequal Average power = true power (kW) ; V × I = apparent power (kVA) The power to overcome reactance = reactive power (kVAR) They form a right-angled triangle: kVA² = kW² + kVAR² Worked: 115 V, 10 A, p.f. 0.8: 1150 VA, 920 W , 690 VAR R = XL : φ = 45°, small negative loops true 920 W reactive 690 VAR apparent 1150 VA 115 V × 10 A, p.f. 0.8
Chapter 10 · Introduction to AC
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
A practical AC circuit always has some resistance and some inductance, and sometimes capacitance as well. If both inductance and capacitance are present they partly cancel, leaving the circuit inductive or capacitive overall. In the graph the resistance equals the inductive reactance, so the current lags by forty-five degrees. Now the positive loops of power are bigger than the negative loops, so there is a net flow of energy into the circuit. The average is the true power, in kilowatts. The r.m.s. volts times amps is the apparent power, in kVA, and the part needed to drive current through the reactance is the reactive power, in kVAR. These three form a right-angled triangle, just like resistance, reactance and impedance did. In the example, one hundred and fifteen volts and ten amps is one thousand one hundred and fifty volt-amps apparent. With a power factor of zero point eight, the true power is nine hundred and twenty watts and the reactive power six hundred and ninety VAR.
Part 3 · Power factor
The power factor = true power ÷ apparent power Power factor = kW ÷ kVA = cos φ , where φ is the phase angle between V and I. True power = V × I × p.f. Alternators are rated in kVA .
Circuit Phase angle φ True power Power factor Pure resistance 0° (in phase) = apparent power 1 (unity, its maximum)R and L equal 45°, current lagging 0.707 × apparent 0.707 Mainly inductive (motors) between 0° and 90° lagging less than apparent less than 1, lagging Pure inductance 90°, current lagging zero 0 (its minimum)Pure capacitance 90°, current leading zero 0, leading Any circuit with reactance not 0° less than V × I less than 1 (never above 1)
Other names: apparent power = theoretical or rated power (VA, kVA); true power = real, effective, wattful or working power (W, kW); reactive power = wattless power (VAR, kVAR).
Chapter 10 · Introduction to AC
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
The power factor links true power and apparent power: it is the true power divided by the apparent power, kilowatts over kVA, and it also equals the cosine of the phase angle. Go down the table. In a pure resistance the angle is zero, cos zero is one, all the apparent power is true power, and the power factor is one, its maximum, often called unity. As the phase angle grows the true power shrinks compared with the apparent power. With equal R and X L, at forty-five degrees, the power factor is zero point seven zero seven. In a pure inductance or a pure capacitance the angle is ninety degrees, cos ninety is zero, the true power is zero and so is the power factor, its minimum. So whenever there is reactance in a circuit, the power factor is less than one. It is never above one. Because a generator heats up with its current, whatever the power factor, alternators are rated in kVA, not kilowatts.
Part 4 · Three phases
Three windings, three phases, 120° apart Three separate stator windings, set 120° apart , under one rotating field The number of separate windings sets the number of phases Three outputs of the same frequency and size , displaced 120° in time Phase sequence A, B, C : A peaks first, then B, then CBetter power-to-weight , easier to parallel ; the aircraft standard A A' B B' C C' windings 120° apart A B C peaks in the order A, B, C Same frequency, same size, displaced 120° in time phase sequence A B C
Chapter 10 · Introduction to AC
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Real aircraft generators are three-phase machines. Instead of one winding on the stator there are three separate windings, set one hundred and twenty degrees apart round the stator, and one rotor magnet turns inside them all. Watch the red arrow, the rotor's north pole. It sweeps past the first winding, phase A, then a third of a turn later past the second winding, phase B, and then the third winding, phase C. Each winding produces its own sine wave, all with the same frequency and the same size, but each one hundred and twenty degrees behind the one before. The number of separate stator windings decides the number of phases. The order in which the phases peak, A then B then C, is the phase sequence, and it matters, for example, for the direction a three-phase motor turns. Three-phase machines give more power for their weight and are easier to run in parallel, which is why three-phase has become the standard for aircraft.
Part 4 · Three phases
Star and delta: phase and line values Star (wye): 4 wires A B C neutral N (earthed) line 200 V phase 115 V Why 200 V? VA 115 VB 115 VA − VB 2 × 115 × cos 30° = 115 × √3 ≈ 200 V Delta (mesh): 3 wires no neutral VL = VP · IL = √3 × IP Star : VL = 1.73 × VP (200 = 1.73 × 115), IL = IP . Delta : VL = VP , IL = 1.73 × IP . Aircraft standard: 115/200 V, 400 Hz, three-phase, star .
Chapter 10 · Introduction to AC
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
The three windings can be joined in two ways. In the star connection, one end of each winding is joined to a common point, the neutral, which in aircraft is earthed to the airframe. The other ends feed the three lines. A voltmeter from a line to neutral reads across one winding: that is the phase voltage, one hundred and fifteen volts. A voltmeter between two lines reads across two windings, and because their voltages are one hundred and twenty degrees apart, the result is not double but root three times as much, one point seven three times one hundred and fifteen, about two hundred volts, the line voltage. In star, line current equals phase current. In the delta connection the windings form a closed triangle with no neutral. Then line voltage equals phase voltage, but each line current is one point seven three times the phase current. So the aircraft standard is one hundred and fifteen over two hundred volts, four hundred hertz, three-phase star.
Summary
What to take into the exam Why AC Lighter, simpler machines; transformers ~100% efficient; TRUs for DC; no commutator; lighter cables.
Frequency f = (poles ÷ 2) × (rpm ÷ 60). 8 poles at 6000 rpm = 400 Hz. T = 1/f. Speed sets f; field current sets V.
r.m.s. 0.707 × peak; same heating as DC. Meters and supply values are r.m.s. 115 V r.m.s. = 162.6 V peak.
CIVIL C: I leads V by 90°. L: I lags V by 90°. R: in phase. Reactive circuit: V and I out of phase.
Reactance XL = 2πfL rises with f; XC = 1/2πfC falls. Low frequency: inductive current up, devices overheat.
Impedance Z = √(R² + (XL − XC )²): vector sum. Series resonance: I max; parallel: I min.
Power True kW, reactive kVAR, apparent kVA. p.f. = kW ÷ kVA = cos φ; 1 resistive, 0 pure L or C. Alternators rated in kVA.
Three phase Windings 120° apart. Star: VL = 1.73 VP (115/200 V), IL = IP . Delta: VL = VP , IL = 1.73 IP .
Chapter 10 · Introduction to AC
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the key points. AC wins on large aircraft: lighter, simpler machines, transformers, T R Us, no commutator and lighter cables. Frequency is set by poles and speed: eight poles at six thousand r p m gives four hundred hertz. The r.m.s. value is zero point seven zero seven of the peak and gives the same heating as that much DC; meters read r.m.s. Remember CIVIL: in a capacitor the current leads by ninety degrees, in an inductor it lags by ninety, and in a resistance it is in phase. Inductive reactance rises with frequency and capacitive reactance falls, so a low frequency makes inductive devices draw more current and overheat. Power comes in three kinds, true, reactive and apparent, and the power factor is kilowatts over kVA, the cosine of the phase angle. And in a star-connected three-phase system the line voltage is one point seven three times the phase voltage: one hundred and fifteen over two hundred volts.