Electrics · Chapter 1
Basic Electrical Principles Charge and current, voltage and resistance, Ohm’s law and power, series and parallel circuits, Kirchhoff’s laws, the Wheatstone bridge and electrical meters.
+ − R V = I × R volts = amps × ohms © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to Electrics, and to chapter one, basic electrical principles. Everything electrical on an aircraft, from a reading light to the flight control computers, obeys a handful of simple rules. In this chapter we start with the electron and see what makes it move. Then we meet voltage, current and resistance, tie them together with Ohm’s law, and work out power and heating. After that we solve series and parallel circuits with Kirchhoff’s two laws, balance a Wheatstone bridge, and see how ammeters and voltmeters are connected. Get these ideas firm now, because every later chapter builds on them.
Chapter 1
The rules every circuit obeys Electrons charge and flow 1 V · I · R the three quantities 2 Ohm’s law V = I × R 3 Power P = V × I 4 Circuits series · parallel 5 Kirchhoff junctions and loops 6 Bridge, meters measuring 7 Part 1 · The electron Atoms, free electrons, conductors and insulators, and which way current flows.
Part 2 · V, I and R EMF, current, resistance, units and prefixes, and what changes resistance.
Part 3 · Ohm’s law and power V = I × R, the three power formulae, and why heat rises with current squared.
Part 4 · Circuits Series, parallel, Kirchhoff’s laws, the Wheatstone bridge and meters.
Chapter 1 · Basic Electrical Principles
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the map for this chapter. In part one we look inside the atom to find the free electrons that carry current, and settle which way current is said to flow. In part two we define the three quantities you will use in every electrical question, voltage, current and resistance, with their units and prefixes, and see what makes a wire’s resistance bigger or smaller. Part three ties them together with Ohm’s law and the formulae for power, including the important fact that heating rises with the square of the current. Part four puts it to work on series and parallel circuits, Kirchhoff’s two laws, the Wheatstone bridge, and how meters are connected. There are lots of worked numbers on the way, so have a pencil ready.
Part 1 · The electron
Atoms, free electrons and conductors An atom has a positive nucleus and negative electrons in orbit; normally the charges balance, so it is neutral Outer electrons are loosely held: these free electrons wander from atom to atom An atom that loses an electron is a positive ion ; one that gains an electron is a negative ion Conductors (silver, copper, aluminium) have many free electronsInsulators (rubber, glass, plastics, wood) have very fewMake the free electrons drift one way and you have an electric current + − − + − − − free electron nucleus (+) and bound electrons (−) atom stays neutral overall Conductors many free electrons silver, copper, aluminium low resistance Insulators very few free electrons rubber, glass, plastic, wood very high resistance
Chapter 1 · Basic Electrical Principles
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
All matter is built from atoms, and every electrical effect comes down to the movement of electrons. An atom has a nucleus carrying positive charge, with negative electrons in orbit around it. Normally the positive and negative charges are equal, so the atom is electrically neutral. Electrons close in are held tightly by the nucleus, but those in the outer orbits are only loosely held, and they can break away and wander to a neighbouring atom. We call these free electrons. If an atom loses an electron it is left with more positive charge and becomes a positive ion; if it gains one it becomes a negative ion. Materials with many free electrons, like silver, copper and aluminium, are conductors. Materials with very few, like rubber, glass, plastics and wood, are insulators. Make the free electrons drift in one direction and you have an electric current.
Part 1 · The electron
A complete circuit, and which way current flows A source pushes electrons: its negative terminal repels them, its positive terminal attracts them The source must take electrons back in and return them to the negative side, or flow stops So current flows only round a complete (closed) circuit ; open the switch and it stops everywhere Electron flow : from negative to positive round the external circuitConventional current : from positive to negative , the older convention used in every rule and diagram+ − 28 V conventional current: + to − electron flow: − to + Current flows only round a complete circuit Inside the source, charge is pushed back to the start
Chapter 1 · Basic Electrical Principles
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
A source of electricity, such as a battery, pushes free electrons round a circuit. Its negative terminal repels electrons and its positive terminal attracts them, so they drift through the wire from negative to positive. To keep this going, the battery must take in the electrons arriving at its positive terminal and transfer them through itself back to the negative side. If it could not, they would simply pile up and the flow would stop. That is why current only flows round a complete, closed circuit. When the switch closes, the loop is complete and the lamp lights; open it anywhere and the current stops everywhere at once. Now a point that catches students out. Electricity was used long before the electron was discovered, and people assumed something flowed from positive to negative. That conventional current, positive to negative, is still used in all the rules and diagrams. Electron flow is the real movement, the opposite way.
Part 1 · The electron
Six ways to make electrons flow Friction Static electricity : rubbing transfers electrons. Builds up on airframes in flight.
Chemical action Cells and batteries , primary (throw-away) and secondary (rechargeable).
Magnetism Generators and alternators : a conductor moving through a magnetic field.
Heat Thermocouples : a heated junction of two dissimilar metals, e.g. EGT probes.
Light Photo-electric cells : light falling on the cell releases electrons.
Pressure Piezo-electric crystals : squeezing the crystal produces a voltage.
Chapter 1 · Basic Electrical Principles
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are six basic ways to produce the force that makes electrons flow. Friction gives static electricity: rubbing two materials moves electrons from one to the other, and an aircraft builds up static charge just by flying through the air. Chemical action is used in cells and batteries. Magnetism is used in generators and alternators, where a conductor moves through a magnetic field. Heat produces a voltage at a thermocouple, the heated junction of two different metals, which is how exhaust gas temperature is measured. Light falling on a photo-electric cell releases electrons. And pressure on a piezo-electric crystal produces a small voltage. Remember for the exam that only two of the six, chemical action in batteries and magnetism in generators, give electrical power in useful quantities. The others are used mainly for sensing and measurement.
Part 2 · V, I and R
EMF and potential difference: the electrical pressure Electromotive force (EMF) is the electrical "pressure" that drives current, like pressure in a water pipePotential difference (PD) is the difference in electrical potential between two pointsBoth are measured in volts (V) ; symbol V or E More voltage, more current; aircraft systems hold the voltage constant (generators and regulators) Prefixes: µV (millionth), mV (thousandth), kV (thousand) A voltmeter is connected across the two points, without breaking the circuit Water Electricity narrow pipe height = pressure pump keeps the tank topped up + − EMF R voltage ⇄ water pressure current ⇄ flow rate resistance ⇄ narrow pipe
Chapter 1 · Basic Electrical Principles
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
For current to flow, something must push it. That push is called the electromotive force, or EMF, and it is very like pressure in a water system. A tank raised high pushes water through a pipe; the higher the tank, the greater the pressure and the faster the flow, while a narrow section of pipe holds the flow back. In a circuit, the EMF of the battery plays the part of the pressure, the current is the flow, and resistance is the narrow pipe. The difference in electrical potential between any two points is called the potential difference. Both EMF and potential difference are measured in volts, and the symbol is V or E. Raise the voltage and more current flows; lower it and less flows, so aircraft generators are regulated to hold the voltage steady. A voltmeter measures volts, and it is connected across the two points of interest without breaking the circuit.
Part 2 · V, I and R
Current: the rate of flow of charge Current (I) is the amount of charge passing a point each secondMeasured in amperes (A) : 1 A = 1 coulomb per second , about 6.24 × 10¹⁸ electrons Small currents: mA (thousandths) and µA (millionths) An ammeter is connected in series , so the circuit current passes through it In a simple loop the current is the same at every point electron drift current I 1 A = 1 coulomb per second ≈ 6.24 × 10¹⁸ electrons per second A + − ammeter in series: all the current passes through it mA = 10⁻³ A · µA = 10⁻⁶ A
Chapter 1 · Basic Electrical Principles
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Current is the rate at which electric charge flows past a point in a circuit. Its symbol is I, and it is measured in amperes, or amps for short. One amp means one coulomb of charge passing every second, and a coulomb is about six point two four million million million electrons, so even a small current involves an enormous number of electrons. For small currents we use the milliamp, a thousandth of an amp, and the microamp, a millionth. To measure current we use an ammeter, and it must be connected in series, that is, the circuit is broken and the ammeter put into the gap so that all of the current passes through it. In a simple single loop, the current is the same at every point: the electrons cannot pile up anywhere, so what goes past one point must go past every other.
Part 2 · V, I and R
Three effects of an electric current Heating A current always heats the conductor it flows through.Uses: heaters, irons, lamp filaments, windscreen heat, fuses .Downside: wasted energy and overheated cables.
Magnetic A current always sets up a magnetic field round the conductor.Uses: motors, generators, transformers, relays and solenoids , circuit-breaker trips.
Chemical A current through an electrolyte causes a chemical change in the liquid and the metal plates.Uses: battery charging , electroplating.
Chapter 1 · Basic Electrical Principles
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whenever current flows, it produces up to three effects. The heating effect is always present: every conductor gets warm when current passes through it. We use it in heaters, lamp filaments, windscreen heating and, very importantly, in fuses, which melt when the current is too high. But it is also wasted energy, and it is what overheats cables in a fault. The magnetic effect is also always present: a current sets up a magnetic field round its conductor. That gives us motors, generators, transformers, relays, solenoids and the magnetic trips in some circuit breakers. The third is the chemical effect. When current passes through certain liquids, called electrolytes, it causes a chemical change in the liquid and in the metal plates standing in it. That is how a battery is recharged, and how electroplating works.
Part 2 · V, I and R
Resistance and what affects it Resistance (R) opposes the flow of current; unit the ohm (Ω) 1 Ω: one volt drives one amp through it Material : more free electrons, lower resistance (silver is better than copper)Length : longer wire, more resistance (R ∝ L)Cross-sectional area : thicker wire, less resistance (R ∝ 1/A)Temperature : changes resistance (next slide)R = ρ × L ÷ A ρ = resistivity of the material reference wire R twice as long 2 R twice the diameter R ÷ 4 Area grows with diameter squared: 2 × diameter → 4 × area Also: resistance changes with temperature
Chapter 1 · Basic Electrical Principles
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Anything that opposes the flow of current is called resistance. Its symbol is R and its unit is the ohm. A component has a resistance of one ohm if one volt drives a current of one amp through it. Four things decide the resistance of a wire. First, the material: a material with more free electrons conducts better, so silver beats copper, and copper beats aluminium. Second, length: double the length and you double the resistance, because the electrons have twice as far to struggle. Third, cross-sectional area: a thicker wire offers more paths, so the resistance falls. Watch the trap here. If you double the diameter of a wire, its area goes up four times, so its resistance falls to a quarter, not a half. Fourth, temperature, which we look at next. Cable sizes on an aircraft are chosen with all of this in mind: big currents need thick cables to keep the heating down.
Part 2 · V, I and R
Temperature coefficient: PTC and NTC The change of resistance with temperature is the temperature coefficient , symbol α (alpha) PTC , positive: resistance rises as temperature rises (most metals, e.g. copper)NTC , negative: resistance falls as temperature rises (carbon, semiconductor thermistors)Copper: α ≈ 0.004 per °C, so about +0.4% per degree Used in aircraft temperature sensors : oil, air and fluid temperatures 0 20 40 60 80 100 0 0.5 1 1.5 2 2.5 temperature (°C) R ÷ R at 20 °C PTC: copper wire NTC: thermistor Both are used to measure temperature
Chapter 1 · Basic Electrical Principles
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The resistance of most materials changes with temperature, and the amount it changes per degree is called the temperature coefficient, with the symbol alpha. If the resistance rises as the temperature rises, the material has a positive temperature coefficient, or PTC. Most metals behave like this; copper’s resistance goes up by roughly zero point four per cent for every degree, which is why the copper line on the graph climbs gently. If the resistance falls as temperature rises, the material has a negative temperature coefficient, or NTC. Carbon and the semiconductor devices called thermistors behave like this, and as you can see, a thermistor changes very strongly. Both effects are put to good use: a resistor of known coefficient placed in the oil, the air or a fluid line changes its resistance with temperature, and a measuring circuit turns that into a temperature reading on the flight deck.
Part 2 · V, I and R
Quantities, symbols, units and meters Quantity Symbol Unit Measured with Connected EMF / potential difference V or E volt (V) voltmeter in parallel (across)Current I ampere (A) ammeter in series Resistance R ohm (Ω) ohmmeter across a dead component Power P (or W)watt (W) wattmeter current and voltage coils Charge Q coulomb (C) — 1 C = 1 A for 1 s Energy / work W joule (J) energy meter 1 J = 1 W for 1 s
Exam traps: EMF is measured in volts (not watts or amps); power in watts ; an ammeter measures current, a voltmeter measures EMF or potential difference.
Chapter 1 · Basic Electrical Principles
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table pulls together the quantities you will meet in almost every electrical question. Electromotive force and potential difference have the symbol V or E and are measured in volts with a voltmeter, connected in parallel, across the two points. Current has the symbol I, is measured in amps, and the ammeter goes in series. Resistance, R, is measured in ohms, and an ohmmeter is used on a component that is switched off, because it uses its own small battery. Power, P, is measured in watts. Charge is measured in coulombs, one coulomb being one amp flowing for one second, and energy is measured in joules, one joule being one watt for one second. The exam loves to swap these around, offering you EMF measured in watts or current measured in volts, so learn the pairs until they are automatic.
Part 2 · V, I and R
Prefixes: moving the decimal point Each prefix step is a factor of 1000 M mega = 10⁶ · k kilo = 10³ · m milli = 10⁻³ · µ micro = 10⁻⁶Bigger prefix, smaller number : 1250 Ω = 1.25 kΩ Smaller prefix, bigger number : 1.5 MΩ = 1500 kΩ Check the size: 550 kΩ is just over half a megohm, 0.55 MΩ M mega × 1 000 000 k kilo × 1000 – base unit × 1 m milli ÷ 1000 µ micro ÷ 1 000 000 Worked conversions 1250 Ω = 1.25 kΩ 1.5 MΩ = 1500 kΩ 550 kΩ = 0.55 MΩ 0.04 A = 40 mA 2500 µF = 2.5 mF Each step down the ladder: the number gets 1000 × bigger Each step up the ladder: the number gets 1000 × smaller Sense check: 550 000 Ω is just over half a million ohms
Chapter 1 · Basic Electrical Principles
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Electrical values range from millionths to millions, so we use prefixes, and every step on the ladder is a factor of one thousand. Mega means a million, kilo a thousand, milli a thousandth and micro a millionth. The rule to remember is that when you move to a bigger prefix, the number gets smaller, and when you move to a smaller prefix, the number gets bigger. So one thousand two hundred and fifty ohms is one point two five kilohms. One point five megohms, moving down one step to kilohms, becomes one thousand five hundred kilohms. Five hundred and fifty kilohms, moving up a step, becomes nought point five five megohms. Forty milliamps is nought point nought four amps. Always do a quick sense check: five hundred and fifty thousand ohms is just over half a million, so nought point five five megohms must be right.
Part 2 · V, I and R
Resistors and their symbols Resistors are fitted to set or limit the current in a circuitFixed : one value, drawn as a plain rectangleVariable (rheostat): value adjusted, arrow drawn through itPotentiometer : sliding contact taps off part of the voltage, e.g. a position transmitter or dimmerThermistor : deliberately temperature-sensitive, for sensingFixed resistor set value, e.g. 470 Ω Variable resistor value adjusted (rheostat) Potentiometer sliding contact: a voltage divider t° Thermistor resistance changes with temperature Zigzag form older / American drawings
Chapter 1 · Basic Electrical Principles
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes we want resistance on purpose, to set or limit the current in a circuit, and then we fit a resistor of a known value. A fixed resistor has one value and is drawn as a plain rectangle in modern diagrams; older and American drawings use a zigzag line, and you should recognise both. A variable resistor, sometimes called a rheostat, can have its value adjusted, and is drawn with an arrow through it. A potentiometer has a sliding contact, the wiper, that taps off part of the voltage across it. That makes it a voltage divider, used for things like panel lighting dimmers and position transmitters, where the wiper is moved by the device being measured. Finally the thermistor, which we have just met, is a resistor made deliberately sensitive to temperature, and drawn with a bent line through it and a small t for temperature.
Part 3 · Ohm’s law and power
Ohm’s law At constant temperature, current is directly proportional to voltage And inversely proportional to resistance V = I × R , so I = V ÷ R and R = V ÷ I Volts = amps × ohms On a graph of I against V, a resistor is a straight line ; the lower the resistance, the steeper the line 0 4 8 12 16 20 24 28 0 2 4 6 8 voltage V (volts) current I (amps) 4 Ω 8 Ω 14 Ω 28 V ÷ 14 Ω = 2 A Straight line: current ∝ voltage (resistance fixed)
Chapter 1 · Basic Electrical Principles
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ohm’s law links the three quantities together, and it is the single most useful rule in electrics. If the resistance stays the same, the current is directly proportional to the voltage: double the voltage and you double the current. If the voltage stays the same, the current is inversely proportional to the resistance: double the resistance and the current halves. Put together, the voltage equals the current multiplied by the resistance. Rearranged, the current equals the voltage divided by the resistance, and the resistance equals the voltage divided by the current. On the graph, each resistor gives a straight line through the origin. The four ohm resistor gives the steepest line, because a low resistance lets the most current through, while the fourteen ohm resistor passes just two amps at twenty-eight volts. In the exam, the correct statement is always current directly proportional to voltage and inversely proportional to resistance.
Part 3 · Ohm’s law and power
Ohm’s law with aircraft numbers Cover the quantity you want: V = I × R · I = V ÷ R · R = V ÷ I
Find the current 28 V across a 14 Ω heater.I = 28 ÷ 14 = 2 A
Find the voltage 2 A through a 4.6 Ω resistor.V = 2 × 4.6 = 9.2 V dropped across it.
Find the resistance A 24 V relay coil draws 0.5 A.R = 24 ÷ 0.5 = 48 Ω
What if… Same resistor, voltage doubled: current doubles . Same voltage, resistance doubled: current halves .
Chapter 1 · Basic Electrical Principles
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put Ohm’s law to work with some aircraft numbers. A neat way to remember it is the triangle: V on top, I and R underneath; cover the one you want and the other two show you what to do. Twenty-eight volts across a fourteen ohm heater: the current is twenty-eight divided by fourteen, which is two amps. Two amps flowing through a four point six ohm resistor: the voltage dropped across it is two times four point six, which is nine point two volts. A twenty-four volt relay coil drawing half an amp has a resistance of twenty-four divided by nought point five, which is forty-eight ohms. And the what-if questions: if the voltage across a fixed resistor doubles, the current doubles; if the resistance doubles at the same voltage, the current halves. Always check that your units are volts, amps and ohms before you divide.
Part 3 · Ohm’s law and power
Power: the rate of doing work Power is the rate at which work is done; unit the watt (W) , 1 W = 1 joule per secondCurrent through a resistance does work: heat , magnetism or chemical action P = V × I (watts = volts × amps)Combine with Ohm’s law: P = I² R and P = V² ÷ R Example: 80 W at 8 A needs 80 ÷ 8 = 10 V P = V × I know volts and amps P = I² × R voltage unknown P = V² ÷ R current unknown Example: a 28 V lamp drawing 2 A P = 28 × 2 = 56 W R = V ÷ I = 14 Ω → I² R = 4 × 14 = 56 W ✓ V² ÷ R = 784 ÷ 14 = 56 W ✓ 1 watt = 1 joule per second
Chapter 1 · Basic Electrical Principles
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a force produces movement, work is done, and the rate of doing work is called power. In a circuit, the voltage does work by driving current through a resistance, and that work comes out as heat, magnetism or chemical action. Power is measured in watts, and one watt is one joule of energy every second. The basic formula is simple: power in watts equals volts multiplied by amps. A twenty-eight volt lamp drawing two amps uses fifty-six watts. Combining this with Ohm’s law gives two more forms. If you do not know the voltage, use current squared times resistance. If you do not know the current, use voltage squared divided by resistance. All three give fifty-six watts for our lamp, as the working shows. A typical exam question: a device consuming eighty watts at eight amps must have a supply of eighty divided by eight, which is ten volts.
Part 3 · Ohm’s law and power
Heating rises with the square of the current 0 1 2 3 4 0 20 40 60 80 100 120 current (A) heat (W) 7 W 28 W 112 W Heat = I² R R fixed at 7 Ω 2 A → 28 W 4 A → 112 W Double the current, four times the heat Overload → overheating so every circuit is protected Every component has a power rating (a 60 W lamp, a 5 W resistor). Exceed it and the component overheats, so each circuit is protected by a fuse or circuit breaker .
Chapter 1 · Basic Electrical Principles
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The heat produced in a resistor is the current squared times the resistance, and that square makes all the difference. Here the resistance is fixed at seven ohms. At one amp it produces seven watts. At two amps it produces twenty-eight watts. At four amps, double the current again, it produces one hundred and twelve watts, four times as much as at two amps. So a fairly small increase in current gives a big increase in heating. That is why every electrical component is given a power rating, the maximum wattage it can handle, such as a sixty watt lamp. If that rating is exceeded, the component overheats, and if the current keeps rising a wire or resistor will eventually melt. To stop that happening, every circuit on an aircraft is protected by a fuse or a circuit breaker, which breaks the circuit when the current rises too far. That is the subject of chapter three.
Part 4 · Circuits
Series circuits: one path for the current Components one after another: one path , the same current through all R total = R1 + R2 + R3 The supply voltage is shared : each resistor drops V = I × R Adding resistance reduces the current and the power Drawbacks: loads cannot be controlled separately , and one failure breaks the whole circuit R1 = 4 Ω 2.4 V R2 = 6 Ω 3.6 V R3 6 V 10 Ω + − 12 V I = 0.6 A R total = 4 + 6 + 10 = 20 Ω I = 12 ÷ 20 = 0.6 A (the same everywhere) Drops: 2.4 + 3.6 + 6 = 12 V
Chapter 1 · Basic Electrical Principles
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a series circuit the components are connected one after another, so there is only one path and the same current flows through every one of them. The total resistance is simply the sum of the individual resistances. Take a twelve volt supply with resistors of four, six and ten ohms in series. The total is twenty ohms, and the current is twelve divided by twenty, which is nought point six amps, everywhere in the loop. Each resistor drops a share of the supply voltage in proportion to its resistance: two point four volts across the four ohm, three point six across the six ohm and six volts across the ten ohm, adding back to twelve. Series connection reduces the current and the power used, but it has two big drawbacks for aircraft: the loads cannot be switched or controlled separately, and if any one of them fails open, the whole circuit stops.
Part 4 · Circuits
Parallel circuits: the aircraft way Components side by side: every branch gets the same voltage Branch currents add up to the supply current 1 ÷ R total = 1/R1 + 1/R2 + 1/R3 ; for two: R1 × R2 ÷ (R1 + R2) R total is always less than the smallest branch Each load can be switched and protected separately ; one failure does not stop the others: most aircraft loads are in parallel + − 12 V 4 Ω 3 A 6 Ω 2 A 10 Ω 1.2 A 6.2 A 1 ÷ R total = 1/4 + 1/6 + 1/10 = 31/60 R total = 60 ÷ 31 ≈ 1.94 Ω (less than 4 Ω) I = 3 + 2 + 1.2 = 6.2 A Every branch has the full 12 V
Chapter 1 · Basic Electrical Principles
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a parallel circuit the components sit side by side, each connected directly across the supply, so every branch gets the same full voltage. Using the same three resistors on twelve volts, the four ohm branch takes three amps, the six ohm branch takes two amps and the ten ohm branch takes one point two amps. The supply current is the total of the branches, six point two amps. To find the total resistance, add the reciprocals: one quarter plus one sixth plus one tenth is thirty-one sixtieths, so the total is sixty over thirty-one, about one point nine four ohms. Notice that it is less than the smallest branch; adding a branch always lowers the total resistance. For just two resistors, use the product over the sum. Parallel wiring lets each load be switched and protected on its own, and one failure does not affect the rest. That is why most aircraft loads are connected in parallel.
Part 4 · Circuits
Series-parallel circuits, step by step R1 = 4 Ω 16 V 10 Ω 1.5 A 6 Ω 2.5 A + − 31 V 15 V across the pair 1 Parallel pair first (10 × 6) ÷ (10 + 6) = 60 ÷ 16 = 3.75 Ω 2 Add the series part 4 + 3.75 = 7.75 Ω 3 Total current 31 ÷ 7.75 = 4 A 4 Voltage drops 4 A × 4 Ω = 16 V; 4 A × 3.75 Ω = 15 V 5 Branch currents 15 ÷ 10 = 1.5 A; 15 ÷ 6 = 2.5 A (sum 4 A ✓)
Chapter 1 · Basic Electrical Principles
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many real circuits mix series and parallel, and the method is always the same: deal with the parallel groups first, then add the series parts. Here a four ohm resistor is in series with a pair of ten ohms and six ohms in parallel, on a thirty-one volt supply. Step one, the parallel pair: product over sum, ten times six is sixty, divided by ten plus six, sixteen, gives three point seven five ohms. Notice it is less than the six ohms, as it must be. Step two, add the series resistor: four plus three point seven five is seven point seven five ohms. Step three, the total current is thirty-one divided by seven point seven five, which is four amps. Step four, the voltage drops: sixteen volts across the four ohm resistor, and fifteen volts across the pair. Step five, the branch currents: one point five amps through the ten ohms and two point five through the six, adding back to four.
Part 4 · Circuits
Kirchhoff’s first law: junctions The total current flowing into a junction equals the total current flowing out Charge cannot pile up or vanish at a point Example: 5 A in = 3 A + 2 A out It is why branch currents in a parallel circuit add up to the supply current Use it to find an unknown branch current 5 A in 3 A out 2 A out junction Σ I in = Σ I out: 5 = 3 + 2
Chapter 1 · Basic Electrical Principles
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Kirchhoff’s first law is about junctions, the points where wires meet. It says that the total current flowing into a junction equals the total current flowing out of it. That is common sense once you remember that current is a flow of charge: charge cannot pile up at a point, and it cannot disappear. So if five amps flow into this junction, and three amps leave along one wire, the other must be carrying two amps out. This is exactly why the branch currents in a parallel circuit add up to the supply current, as we saw a moment ago. In practice you use the first law to find an unknown current. If a bus bar is fed with fifty amps and you know what three of its four loads are drawing, the fourth must be taking the remainder.
Part 4 · Circuits
Kirchhoff’s second law: loops 2 Ω 4 V 4 Ω 8 V 8 Ω 16 V + − 28 V I = 28 ÷ 14 = 2 A 4 + 8 + 16 = 28 V = supply ✓ 0 4 8 12 16 20 24 28 potential (V) + terminal after 2 Ω after 4 Ω − terminal −4 V −8 V −16 V In any closed loop, the sum of the voltage drops equals the applied voltage (the EMF).
Chapter 1 · Basic Electrical Principles
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Kirchhoff’s second law is about closed loops. It says that if you add up all the voltage drops round a closed circuit, the total always equals the voltage applied to that circuit. Let us prove it with numbers. A twenty-eight volt supply feeds resistors of two, four and eight ohms in series. The total resistance is fourteen ohms, so the current is twenty-eight divided by fourteen, two amps. Now the drops: two amps through two ohms is four volts, through four ohms is eight volts, and through eight ohms is sixteen volts. Four plus eight plus sixteen is twenty-eight, exactly the supply. The graph on the right shows the same thing as a staircase of potential. We leave the positive terminal at twenty-eight volts, fall to twenty-four after the first resistor, to sixteen after the second, and reach zero at the negative terminal after the third.
Part 4 · Circuits
A complete worked network A + − 28 V R1 4.6 Ω R2 12 Ω R3 12 Ω R4 4 Ω R5 7 Ω V1 V2 V3 Parallel group 1/12 + 1/12 + 1/4 = 5/12 → 2.4 Ω Total 4.6 + 2.4 + 7 = 14 Ω Ammeter A 28 ÷ 14 = 2 A V1 (R1) 2 × 4.6 = 9.2 V V2 (group) 2 × 2.4 = 4.8 V V3 (R5) 2 × 7 = 14 V Branches R2, R3: 4.8 ÷ 12 = 0.4 A · R4: 4.8 ÷ 4 = 1.2 A Power total 28 × 2 = 56 W · R5 28 W · R1 18.4 W
Chapter 1 · Basic Electrical Principles
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a full exam-style network that uses everything so far, on a twenty-eight volt supply. Resistor R one, four point six ohms, is in series with a parallel group of twelve, twelve and four ohms, and then R five, seven ohms. Start with the parallel group: one twelfth plus one twelfth plus one quarter is five twelfths, so the group is twelve fifths, two point four ohms. The total is four point six plus two point four plus seven, fourteen ohms, so the ammeter reads twenty-eight divided by fourteen, two amps. Voltmeter V one, across R one, reads two times four point six, nine point two volts. V two, across the group, reads two times two point four, four point eight volts. V three, across R five, reads fourteen volts, and nine point two plus four point eight plus fourteen is twenty-eight. The twelve ohm branches each take nought point four amps, the four ohm branch one point two. Total power is fifty-six watts.
Part 4 · Circuits
The Wheatstone bridge Four resistors in a diamond with a sensitive meter across the middle Adjust a known resistor until the meter reads zero : the bridge is balanced At balance no current flows from B to C, and the products of opposite arms are equal R1 × Rx = R2 × R3 , so Rx = R2 × R3 ÷ R1 Used to measure an unknown resistance , and in temperature-sensing circuits R1 = 100 Ω R2 = 150 Ω R3 = 80 Ω Rx = ? G A B C D + − Balance: G reads 0 → R1 × Rx = R2 × R3 Rx = 150 × 80 ÷ 100 = 120 Ω
Chapter 1 · Basic Electrical Principles
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Kirchhoff’s laws let us analyse a very useful arrangement called the Wheatstone bridge. Four resistors are connected in a diamond, the supply goes across two opposite corners, A and D, and a sensitive centre-zero meter joins the other two corners, B and C. One resistor, Rx, is unknown. A known resistor, here R three, is adjusted until the meter reads zero. The bridge is then balanced: points B and C are at the same potential, so no current flows between them. At balance, the products of the diagonally opposite arms are equal, so R one times Rx equals R two times R three. Rearranged, Rx equals R two times R three divided by R one. In our example that is one hundred and fifty times eighty, divided by one hundred, which is one hundred and twenty ohms. The same principle is used in aircraft temperature-measuring circuits, where a sensing resistor in the bridge changes with temperature and unbalances the bridge.
Part 4 · Circuits
Connecting ammeters and voltmeters Ammeter : in series , with very low resistance , so it does not reduce the current it measuresVoltmeter : in parallel (across), with very high resistance , so it draws almost no currentAn ammeter put across a supply is a near short circuit: it will be damaged Ohmmeter : has its own battery, so use it only on a dead , isolated componentA centre-zero ammeter in the battery lead shows charge or discharge A 14 Ω + − 28 V V reads 2 A reads 28 V Ammeter: in series, very low resistance Voltmeter: in parallel, very high resistance Ohmmeter: own battery, circuit switched off Centre-zero ammeter: shows charge or discharge
Chapter 1 · Basic Electrical Principles
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
A meter must measure the circuit without disturbing it, and that decides how each one is connected. The ammeter goes in series, so the current passes through it, and it is built with a very low resistance so that it hardly changes the current it is measuring. Here it reads two amps. The voltmeter goes in parallel, across the load, and it has a very high resistance, so it draws almost no current itself. Here it reads twenty-eight volts. Never connect an ammeter across a supply: with almost no resistance it becomes a short circuit and will be damaged. An ohmmeter contains its own battery, so it must only be used on a component that is switched off and isolated. Finally, many light aircraft have a centre-zero ammeter in the battery lead. Its needle swings one way when the battery is charging and the other way when it is discharging, which is very useful in flight.
Summary
What to take into the exam Electrons Free electrons carry current. Conventional current + to −, electron flow − to +. Only batteries and generators give useful power.
Units EMF/PD: volts (V or E). Current: amps (I). Resistance: ohms (R). Power: watts. Each prefix step is × 1000.
Resistance Up with length, down with area (2 × diameter → ¼ R). PTC rises with heat, NTC falls.
Ohm’s law V = I R. Current ∝ voltage, inversely ∝ resistance.
Power P = V I = I² R = V² ÷ R. Double the current, four times the heat.
Series / parallel Series: R adds, same current. Parallel: reciprocals add, same voltage, R total < smallest. Aircraft loads in parallel.
Kirchhoff 1st: current in = current out of a junction. 2nd: voltage drops round a loop = applied EMF.
Bridge and meters Balance: R1 × Rx = R2 × R3. Ammeter series, low R; voltmeter parallel, high R.
Chapter 1 · Basic Electrical Principles
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather up the chapter. Current is a flow of free electrons; conventional current goes from positive to negative and electron flow the other way, and only batteries and generators give power in useful amounts. EMF and potential difference are measured in volts, current in amps, resistance in ohms and power in watts, and each prefix step is a factor of a thousand. Resistance rises with length and falls with area, so doubling the diameter quarters it, and it rises with temperature in PTC materials and falls in NTC ones. Ohm’s law: voltage equals current times resistance. Power is volts times amps, and heating goes with the square of the current. In series, resistances add and the current is the same; in parallel, reciprocals add, the voltage is the same, and the total is less than the smallest branch. Kirchhoff covers junctions and loops, the bridge balances when the opposite products are equal, and the ammeter goes in series and the voltmeter across.