Electrics · Chapter 5
Magnetism and Electromagnetism Magnets, flux and permeability, soft and hard materials, the magnetic effect of a current, solenoids and relays, and the force on a conductor.
S
N
current makes magnetism
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter five is about magnetism and electromagnetism. Almost every electrical machine in an aircraft depends on them: generators and alternators, motors and actuators, relays and contactors, transformers, even the compass. In this chapter we start with the permanent magnet and its field, see why soft iron and hard steel behave so differently, and then discover the key link: an electric current makes a magnetic field. From that one idea come the solenoid, the relay and the force that drives every electric motor.
Roadmap
From a bar magnet to a relay and a motor 1 · Magnets Poles, flux lines, attraction and repulsion, the Earth’s field.
2 · Materials Permeability, soft iron and hard steel, saturation, residual magnetism.
3 · Electromagnetism Field round a wire, the corkscrew rule, solenoids and the grasp rule.
4 · Putting it to work Electromagnet strength, relays and solenoids, the motor effect.
Chapter 5 · Magnetism and Electromagnetism
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through magnetism. First the permanent magnet: its poles, the lines of flux that make up its field, and the simple law that like poles repel and unlike poles attract, with a word on the Earth’s own field. Second, magnetic materials. Soft iron and hard steel behave very differently, and that difference decides which one we use for a relay core and which for a permanent magnet. We meet permeability, saturation and residual magnetism. Third, the big discovery: a current flowing in a wire produces a magnetic field. We learn the rules that give its direction, and wind the wire into a coil to make a solenoid. Finally we put electromagnetism to work in relays and solenoids, and see the force on a current-carrying conductor, which is the principle of every electric motor.
Part 1 · Magnets
What a magnet does It attracts iron and steel , most strongly at its two poles Freely suspended, it settles pointing north–south The end that points north is the north-seeking or N pole ; the other is the S pole Around it is a magnetic field : the region where its effects can be detected Iron filings trace the field as lines of flux (lines of force) Both poles are equally strong
S N
attracts iron, strongest at the poles
S N
→ N
hangs north–south
S N
iron filings show the field (lines of flux)
Chapter 5 · Magnetism and Electromagnetism
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us start with what a magnet actually does. First, it attracts pieces of iron and steel, and if you dip a bar magnet into iron filings, they cling mostly to the two ends. Those ends, where the magnetic effect is strongest, are called the poles. Second, if you hang a magnet freely on a thread, it turns and settles pointing north and south. The end that points north is called the north-seeking pole, or simply the N pole, and the other end is the S pole. Third, a magnet is surrounded by a magnetic field, the region in which its effects can be detected. If you put a sheet of paper over a magnet and sprinkle iron filings on it, they arrange themselves into a pattern of curved lines. We call these lines of flux, or lines of force. One exam point: the two poles of a magnet are always equally strong.
Part 1 · Magnets
Lines of flux: the rules
S N
Outside: N → S · inside the magnet: S → N (closed loops)
Lines never cross
Crowded lines = strong field (high flux density), near the poles
Arrow = way a compass N end points
Lines of flux are continuous closed loops : out of N, round to S outside, back from S to N inside. They never cross .
Chapter 5 · Magnetism and Electromagnetism
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This field pattern was computed for a bar magnet, and it shows the rules of flux lines. We give each line a direction, the way the north end of a small compass needle would point if you placed it there. Outside the magnet, the lines leave the north pole and curve round to enter the south pole. Although diagrams often show them stopping at the poles, the lines are really continuous closed loops: inside the magnet they run from south back to north. The lines never cross each other, because at any point the field can only have one direction. Where the lines are crowded together, near the poles, the field is strong; we say the flux density is high. Further away they spread out and the field weakens. Keep these rules in mind, because every field we draw from now on, around wires and coils too, follows them.
Part 1 · Magnets
Like poles repel, unlike poles attract Unlike poles attract : N and S pull togetherLike poles repel : N and N, or S and S, push apartFields combine : lines in the same direction reinforce, opposing lines cancel Between like poles there is a neutral point of zero field Lines behave like stretched elastic that also push sideways on each other
S N S N Unlike poles attract lines run across the gap and pull the poles together S N N S Like poles repel lines turn away: a neutral point in the gap
Chapter 5 · Magnetism and Electromagnetism
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
When two magnets are brought close together, their fields combine. Where lines from the two magnets run the same way, they reinforce each other and the flux density rises. Where they oppose, they tend to cancel out. Watch the top pair first. A north pole faces a south pole, the lines run straight across the gap from one magnet into the other, and like stretched elastic bands they pull the magnets together: unlike poles attract. Now the bottom pair. Here a north pole faces another north pole. The lines from each pole cannot cross, so they bend away from each other and crowd sideways, leaving a neutral point of zero field in the middle of the gap, and the magnets are pushed apart: like poles repel. The same is true for two south poles. So remember the law: like poles repel, unlike poles attract.
Part 1 · Magnets
The Earth is a magnet too The Earth has a magnetic field, roughly like a huge bar magnet inside it A compass needle’s N-seeking end points towards the north magnetic pole Since unlike poles attract, the pole in the far north is magnetically a south-type pole Flux lines leave the southern hemisphere and re-enter in the northern The magnetic poles are not at the true (geographic) poles
S-type pole (“north magnetic pole”) N-type pole
True (geographic) north
True south
N-seeking end points north
Chapter 5 · Magnetism and Electromagnetism
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The reason a suspended magnet points north is that the Earth itself has a magnetic field, rather like a huge bar magnet buried inside it. The north-seeking end of a compass needle is attracted towards the magnetic pole in the far north. But think about the law we just learned: unlike poles attract. So that pole up in the Canadian Arctic must, magnetically speaking, be a south-type pole, and the Earth’s field lines leave the southern hemisphere and re-enter in the north. We still call it the north magnetic pole, because that is where north-seeking ends point. The magnetic poles are some way from the geographic poles, which is why compass users must allow for variation. We will not go further here, because the compass belongs to your instruments course. What matters for electrics is that aircraft wiring can create fields of its own that upset the compass, as we will see shortly.
Part 1 · Measuring magnetism
The magnetic quantities Quantity Symbol Unit Meaning Magnetic flux Φ weber (Wb)The total amount of field: all the lines of flux Flux density B tesla (T) = Wb/m²How crowded the lines are: flux per square metre Magnetomotive force MMF ampere-turns (AT)The “push” that drives flux: turns × current Magnetising force H ampere-turns per metre MMF per metre of the flux path Permeability μ μ = B ÷ H How readily a material carries flux Reluctance S AT per weber Opposition to flux: the magnetic “resistance”
Worked example: 0.002 Wb through a pole face of 0.004 m² gives B = 0.002 ÷ 0.004 = 0.5 T . A magnetic circuit behaves like Ohm’s law: flux = MMF ÷ reluctance .
Chapter 5 · Magnetism and Electromagnetism
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
To work with magnetism we need a few quantities. Magnetic flux, symbol phi, is the total amount of field, all the lines of flux together, measured in webers. Flux density, symbol B, tells you how crowded the lines are: flux per square metre, measured in teslas. For example, two thousandths of a weber passing through a pole face of four thousandths of a square metre gives a flux density of half a tesla. The magnetomotive force is the push that drives flux round a magnetic circuit, rather like voltage in an electric circuit; for a coil it is the number of turns times the current, in ampere-turns. Permeability tells you how readily a material carries flux, and reluctance is the opposition to flux, the magnetic equivalent of resistance. In fact a magnetic circuit follows a law just like Ohm’s law: flux equals magnetomotive force divided by reluctance.
Part 2 · Materials
Permeability: flux prefers iron Soft iron in a field becomes a magnet itself, adding its own flux The flux lines concentrate through the iron: flux density rises This property is permeability ; iron’s is hundreds or thousands of times that of air Out of the field, soft iron loses most of it: low retentivity What little remains is residual magnetism A soft iron case screens an instrument from stray fields
Flux prefers iron
soft iron
high permeability: flux density increased
Magnetic screening
a soft iron case leads flux round the instrument inside
Chapter 5 · Magnetism and Electromagnetism
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
What happens if you put an unmagnetised piece of soft iron into a magnetic field? The flux lines bend towards it and crowd through it, as if the iron were an easier road. The iron itself becomes magnetised and adds lines of flux of its own, so the flux density is increased. This property is called permeability, and soft iron has a permeability hundreds or even thousands of times greater than air. Take the iron out of the field, and it loses most of its magnetism almost at once: we say it has a low retentivity. The little magnetism it keeps is called residual magnetism, and you will meet that phrase again with generators, which rely on it to start up. Permeability has a neat practical use, shown at the bottom. A soft iron case leads the flux round its walls, so an instrument inside is screened from stray magnetic fields.
Part 2 · Materials
Soft iron and hard steel Soft iron (temporary magnet) Hard alloy steel (permanent magnet) Magnetising Easy : high permeabilityDifficult Keeping it Loses it readily : low retentivityRetains it well : high retentivityResidual magnetism A little Most of it Force to demagnetise (coercivity) Small Large Aircraft uses Relay and solenoid cores, transformer cores, generator pole pieces, screens Magnetos, permanent magnet generators, instrument and loudspeaker magnets, the compass
Electromagnet cores must be soft iron , so the field dies when the current stops; permanent magnets are made of hard steel alloys.
Chapter 5 · Magnetism and Electromagnetism
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The two families of magnetic material behave in opposite ways. Soft iron is easily magnetised, because of its high permeability, but it readily loses its magnetism again: it has low retentivity, keeps only a little residual magnetism, and needs only a small reverse force to demagnetise it. That makes it a temporary magnet, and exactly what we want for the core of a relay, a solenoid or a transformer, and for the pole pieces of a generator, because the magnetism must follow the current and die when it stops. Hard alloy steel is the opposite. It is difficult to magnetise, but once magnetised it keeps its magnetism well: high retentivity and a large coercive force. So permanent magnets are made from hard steel alloys, and you find them in magnetos, permanent magnet generators, instruments and the compass. For the exam: permanent magnets are made of steel; temporary magnets are soft iron.
Part 2 · Materials
Inside a magnet: alignment and saturation Think of iron as made of countless tiny molecular magnets Unmagnetised: they form closed chains pointing every way, so their fields cancel Magnetising lines them up with the lines of flux When all are aligned, the material is saturated : it can take no more This is why a magnet can only be so strong, however hard you magnetise it
Unmagnetised random: fields cancel
Partly magnetised many line up
Saturated all aligned: no more
applied field
Chapter 5 · Magnetism and Electromagnetism
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a piece of iron become a magnet? A useful picture is to think of it as made of countless tiny molecular magnets. In an unmagnetised piece of iron they form closed chains, pointing every which way, so their effects cancel and there is no overall field. When the iron is placed in a magnetic field, more and more of these molecular magnets turn to line up with the lines of flux, and the iron becomes magnetised. Keep increasing the magnetising force and eventually every one of them is lined up. At that point the material is said to be saturated, and it cannot be magnetised any further, however hard you try. That is the meaning of saturation in exam questions: when a magnet is unable to accept any more magnetism, it is saturated. Modern physics talks about domains rather than molecules, but the idea is the same.
Part 2 · Materials
Magnetising loops: soft iron versus hard steel
H magnetising force
B flux density
saturation
first magnetisation (from zero)
hard steel: high residual magnetism
soft iron: small residual
large coercive force
Soft iron: tall, narrow loop
easy to magnetise and demagnetise
relay cores, transformers, pole pieces
Hard steel: wide loop
hard to magnetise, keeps it well
permanent magnets
Residual magnetism is what is left when the magnetising force is removed; coercive force is the reverse force needed to remove it.
Chapter 5 · Magnetism and Electromagnetism
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph, computed from a simple model, shows what happens as you magnetise a material, remove the magnetising force, and then reverse it. Across the bottom is the magnetising force, and up the side is the flux density. The dashed line is the first magnetisation, which bends over as the material approaches saturation. Now reduce the magnetising force to zero. The flux density does not fall back to zero; the height where the loop crosses the vertical axis is the residual magnetism. To remove it, you must apply a reverse force, called the coercive force, where the loop crosses the horizontal axis. The blue loop is soft iron: tall and narrow, a small residual and a tiny coercive force, so it is easily magnetised and easily demagnetised. The red loop is hard steel: wide, with a large residual magnetism and a large coercive force, ideal for a permanent magnet.
Part 2 · Materials
Destroying magnetism, and keeping it Heating : above a critical temperature the alignment is lostHammering or heavy vibration shakes the molecules out of lineAn AC solenoid : the field reverses each cycle; withdraw the magnet slowly A soft iron keeper across the poles closes the flux path and preserves strength Store magnets in pairs, unlike poles together, with keepers
S N
Heating
S N
Hammering
AC ∿
AC coil, withdraw
soft iron keeper
a keeper closes the flux path: the magnet stays strong in storage
Chapter 5 · Magnetism and Electromagnetism
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Magnetism can be destroyed in three ways. The first is heating. Heat makes the molecules vibrate, and above a critical temperature, the Curie point, which for iron is about seven hundred and seventy degrees, the alignment is lost completely. The second is hammering, or heavy vibration, which shakes the molecular magnets out of line. The third is to place the magnet inside a solenoid fed with alternating current. The field reverses every cycle, magnetising the material first one way and then the other, and as the magnet is slowly withdrawn the swings become smaller and smaller, leaving it demagnetised. Workshops use this to demagnetise tools. To preserve a magnet, on the other hand, you fit a soft iron keeper across its poles. The keeper gives the flux an easy closed path, and permanent magnets in storage, such as those in a magneto, are kept that way.
Part 3 · Electromagnetism
A current makes a magnetic field Any conductor carrying a current is surrounded by a magnetic field The lines of flux are concentric circles round the wire Stronger current, stronger field; it is strongest close to the wire Reverse the current and the field reverses Switch off and the field disappears
I (conventional)
concentric circles of flux
end-on: current out of page
flux anticlockwise
Chapter 5 · Magnetism and Electromagnetism
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now for the most important discovery in this chapter: an electric current produces a magnetic field. Here a straight wire passes up through a horizontal card. With no current there is nothing to see. Now we switch on, and conventional current flows upwards. Around the wire a magnetic field appears, and its lines of flux are concentric circles centred on the wire. Iron filings on the card would form rings, and small compass needles would line up along the circles. The field is strongest close to the wire and gets weaker further out, and a bigger current gives a stronger field. If you reverse the current, the field reverses direction, and when you switch the current off, the field disappears completely. This is electromagnetism, and every relay, solenoid, motor, generator and transformer in the aircraft depends on it.
Part 3 · Electromagnetism
The corkscrew rule and the dot and cross Drive a right-handed corkscrew along the wire in the direction of the conventional current The way it turns is the direction of the flux End-on: a cross ⊗ is current going into the page (the tail of an arrow) A dot ⊙ is current coming out of the page (the point of an arrow) Into the page: clockwise flux; out of the page: anticlockwise
screw driven along the conventional current →
seen from behind, looking along the current:
it turns clockwise = the flux direction
⊗ into page: clockwise
⊙ out of page: anticlockwise
Chapter 5 · Magnetism and Electromagnetism
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Which way do the circles of flux go round? The corkscrew rule tells us. Imagine a right-handed corkscrew being screwed along the wire in the direction of the conventional current, from positive to negative. The direction in which you have to turn the corkscrew is the direction of the lines of flux. To draw wires end-on, we use a simple code. Think of the current as an arrow. If it is flying away from you into the page, you see its tail feathers, drawn as a cross. If it is coming out of the page towards you, you see its point, drawn as a dot. Apply the corkscrew rule: a cross, current going in, gives clockwise flux, and a dot, current coming out, gives anticlockwise flux. You can also use your right hand: grip the wire with the thumb along the current, and your fingers curl the way of the flux.
Part 3 · Electromagnetism
Two wires: fields combine, wires move
Same direction: attract fields cancel between the wires and add outside Opposite directions: repel fields add between the wires and crowd, pushing apart
Aircraft practice: a DC supply and return run side by side carry opposite currents, so their fields largely cancel . That is why wiring near the compass is run in pairs or twisted.
Chapter 5 · Magnetism and Electromagnetism
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
When two wires lie side by side, their fields combine, and the wires feel a force. On the left, both currents come out of the page. Between the wires their circular fields point in opposite directions and cancel, while outside they add and wrap round both wires together. The lines behave like stretched elastic, so they pull the wires together: currents in the same direction attract. On the right, the currents flow in opposite directions. Now the fields add between the wires, the lines crowd together there and push the wires apart: opposite currents repel. There is a useful practical lesson here. A supply lead and its return lead carry equal and opposite currents, so if they are run close together, their fields largely cancel at a distance. That is why wiring near the standby compass is run in pairs or twisted together, to stop it causing compass deviation.
Part 3 · Electromagnetism
The solenoid: a coil that behaves like a bar magnet A solenoid (electromagnet): many turns of insulated wire Between neighbouring turns the fields cancel ; they add along the axis The result is a field like a bar magnet , with N and S poles A soft iron core multiplies the flux Switch off: the field collapses , leaving a little residual magnetism
S N
field like a bar magnet: out of N, back into S
Chapter 5 · Magnetism and Electromagnetism
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Wind a wire into a coil of many turns, and you have a solenoid, or electromagnet. The wire must be insulated, so that the current goes round every turn instead of short-circuiting between them. When current flows, each turn makes its own little field. Between neighbouring turns the fields point in opposite directions and cancel out, but along the axis they all point the same way and add up. The result, shown by the flowing lines, is a field just like that of a bar magnet, leaving one end, the north pole, and curving round outside to re-enter at the south pole. Slide a soft iron core into the coil and, thanks to its high permeability, the flux is multiplied many times. Switch off the current and the field collapses, leaving only a little residual magnetism in the soft iron core. That on-off control is what makes electromagnets so useful.
Part 3 · Electromagnetism
Finding the poles: the right hand grasp rule Grasp the solenoid in your right hand Curl your fingers round it in the direction of the conventional current in the turns Your outstretched thumb points to the north pole Check from an end: current clockwise = S , anticlockwise = N Reverse the current and the poles swap
S N
fingers curl with the current
thumb → N pole
gold arrows: conventional current down the near side of each turn
S
N
end view: clockwise = S
anticlockwise = N
Chapter 5 · Magnetism and Electromagnetism
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Which end of a solenoid is the north pole? Use the right hand grasp rule. Hold the solenoid in your right hand, so that your fingers curl round it in the same direction as the conventional current flows round the turns. Your outstretched thumb then points to the north pole of the solenoid. There is a handy cross-check that some students prefer. Look straight at one end of the coil. If the current is flowing clockwise as you look at it, that end is a south pole; if it flows anticlockwise, that end is a north pole. You can remember it by drawing the letters: the arrows on a capital S run clockwise round its ends, and those on a capital N anticlockwise. And if you reverse the current, the poles swap over. Practise it on the diagram until it is automatic, because the exam often gives you a coil and asks which end is north.
Part 4 · Electromagnets at work
Making an electromagnet stronger Increase the number of turns Increase the current Use a soft iron core (high permeability) Turns × current = ampere-turns , the magnetomotive force Strength rises until the core saturates Note: raising coil resistance reduces current, so weakens it
Magnetising force = turns × current
200 turns × 1 A 200 AT 200 turns × 2 A 400 AT 400 turns × 2 A 800 AT 400 turns × 2 A + iron core 800 AT
Iron core: same ampere-turns, but its permeability
multiplies the flux hundreds of times
Chapter 5 · Magnetism and Electromagnetism
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do we make an electromagnet stronger? There are three ways, and they are a favourite exam question. Increase the number of turns, increase the current, or put a soft iron core inside the coil. The first two work together as the magnetomotive force, measured in ampere-turns: the number of turns multiplied by the current. Two hundred turns carrying one amp give two hundred ampere-turns. Double the current to two amps and you have four hundred. Double the turns as well, to four hundred, and you have eight hundred. The soft iron core does not change the ampere-turns at all, but its high permeability multiplies the flux they produce many times over, at least until the core saturates. Notice the trap: electromagnetism is a product of current, not voltage. Increasing the coil’s resistance reduces the current and so weakens the magnet.
Part 4 · Electromagnets at work
Relays and solenoids: remote-controlled switches A small current from the flight deck switches a large current at the load Relay : a fixed core attracts a hinged armature , which moves the contactsSolenoid : the core itself moves (a plunger) and carries the contactsThe coil is insulated from the contacts: no electrical connection between the circuits Heavy cables stay short; example: the starter solenoid
Relay Solenoid
hinged armature
fixed core, attracted armature
moving core (plunger) pulled in
Both: a small control current switches a large load current
The coil is insulated : no electrical contact with the load circuit
Example: the starter solenoid of a piston engine
Heavy cables stay short; only light wires go to the flight deck
Chapter 5 · Magnetism and Electromagnetism
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Solenoids and relays are nothing more than remotely controlled switches. A small current, switched from the flight deck through light wiring, energises a coil, and the coil’s magnetism operates contacts that switch a large current right next to the load. Watch the relay. We close the switch in the control circuit, the coil is energised, and its fixed soft iron core pulls the hinged armature down. The armature closes the contacts, and the heavy current flows to the load. In a relay the core is stationary and the armature is attracted to it. In a solenoid, by contrast, the core itself moves: it is a plunger pulled into the coil, carrying a contact plate across two heavy terminals. The starter solenoid of a piston engine is the classic example. In both, the coil is insulated and has no electrical connection with the circuit that the contacts control.
Part 4 · Electromagnets at work
The motor effect: force on a conductor A current-carrying conductor in a magnetic field feels a force Its own field adds to the main field on one side and opposes it on the other The conductor is pushed from the strong side towards the weak side Force = B × I × L : 0.5 T × 10 A × 0.2 m = 1 N Direction: Fleming’s left hand rule ; reverse current or field and the force reverses
thuMb: Motion
First finger: Field N → S
seCond finger: Current conventional, + to −
LEFT hand for MOTORS
(the right hand rule is for generators: chapter 6)
Chapter 5 · Magnetism and Electromagnetism
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Put a conductor between the poles of a magnet and pass a current through it, and it moves. This is the motor effect. Here the main field runs from the north pole to the south pole, and the current in the conductor flows out towards us. The conductor’s own circular field adds to the main field on one side and opposes it on the other, so the lines are crowded on one side and thin on the other. Like a catapult, the stretched lines push the conductor from the strong side towards the weak side, so this conductor is forced upwards. The size of the force is the flux density times the current times the length of conductor in the field: half a tesla, ten amps and twenty centimetres give one newton. For the direction, use Fleming’s left hand rule. Hold thumb, first and second fingers at right angles: the first finger along the field, the second along the current, and the thumb gives the motion.
Part 4 · Electromagnets at work
The catapult field
N
S
neutral point (weak field)
force on the wire
from strong field to weak
current out of the page
lines crowded below: the two fields add
Reverse either the current or the field and the force reverses; reverse both and it stays the same. This is how every DC motor turns.
Chapter 5 · Magnetism and Electromagnetism
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the same situation drawn as a computed field, looking along the conductor. The uniform field runs from the north pole on the left to the south pole on the right. The wire carries current out of the page, shown by the dot, so its own field circles anticlockwise. Below the wire, the wire’s field points the same way as the main field, the two add, and the lines are crowded together. Above the wire, the two fields oppose, so the lines are sparse, and there is even a neutral point where they cancel completely. The crowded lines below behave like a stretched catapult and push the wire upwards, towards the weak field. Notice what happens if you reverse either the current or the field: the crowding moves to the other side and the force reverses. Reverse both and nothing changes. A DC motor is simply a coil arranged so that this force turns it round.
Looking ahead
Motion makes current: induction The motor effect run backwards: move a conductor through a field and an EMF is induced It must cut lines of flux: no relative motion, no EMF Faster motion, stronger field or more turns: bigger EMF Reverse the motion and the EMF reverses This is the principle of every generator and transformer : chapter 6
N
S
move
− 0 +
Cutting flux induces an EMF (Faraday)
Faster cutting or stronger field: bigger EMF
No relative motion: no EMF
Reverse the motion: the EMF reverses (Lenz opposes the cause)
Chapter 5 · Magnetism and Electromagnetism
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Before we leave magnetism, here is a look ahead. We have seen that current in a magnetic field produces motion. The reverse is also true: motion in a magnetic field produces current. If you move a conductor so that it cuts across the lines of flux between two poles, an electromotive force is induced in it, and a sensitive meter connected across it will flick. It does not matter whether the conductor moves or the magnet moves, as long as the conductor cuts flux. Hold it still and there is no E M F. Move it faster, use a stronger field, or use a coil of many turns, and the E M F is bigger. Move it the other way and the E M F reverses. This is electromagnetic induction, and it is the principle of every generator, alternator and transformer in the aircraft. We pick it up properly in the next chapter, with Fleming’s right hand rule for generators.
Summary
What to take into the exam Magnets Attract iron; point N–S; field round them. Both poles equally strong. Like repel, unlike attract.
Flux lines Out of N, into S outside; closed loops; never cross; crowded = strong field.
Materials Soft iron: easy to magnetise, loses it (temporary). Hard steel: holds it (permanent).
Permeability Iron concentrates flux, raising flux density. Saturation: no more magnetism possible.
Current → field Concentric circles round a wire. Corkscrew rule. ⊗ in = clockwise, ⊙ out = anticlockwise.
Solenoid Field like a bar magnet. Right hand grasp: thumb = N. Stronger: more turns, more current, iron core.
Relay / solenoid Small current switches large. Relay: fixed core, moving armature. Solenoid: moving core.
Motor effect Force = BIL, strong side to weak. Fleming left hand: First = Field, seCond = Current, thuMb = Motion.
Chapter 5 · Magnetism and Electromagnetism
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather it all up. A magnet attracts iron, points north and south when suspended, and has a field round it; its two poles are equally strong; like poles repel and unlike poles attract. Flux lines leave the north pole and enter the south pole outside the magnet, form closed loops and never cross. Soft iron is easily magnetised but loses it, so it makes temporary magnets and electromagnet cores; hard steel holds its magnetism and makes permanent magnets. Iron’s permeability concentrates flux, and saturation is the point where no more magnetism is possible. A current produces circles of flux round a wire, given by the corkscrew rule. A solenoid behaves like a bar magnet, with the north pole where the right thumb points, and is made stronger by more turns, more current or an iron core. Relays and solenoids let a small current switch a large one, and a current in a field feels a force, given by Fleming’s left hand rule.