Electrics · Chapter 20
Radio Propagation How radio waves travel: surface, space and sky waves, the ionosphere and HF, then modulation, aerials and the oscillators that make the signal.
ionosphere
surface wave · sky wave · space wave
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
This chapter follows a radio signal from start to finish. First we see how radio waves travel: hugging the ground as a surface wave, flying straight like light as a space wave, or bouncing off the ionosphere as a sky wave, and why the frequency you choose decides which one you get. Then we look at how speech is put onto a carrier wave by amplitude, frequency and phase modulation, and why HF uses single sideband. After that come aerials, their lengths and their radiation patterns, from the simple dipole to radar dishes. Finally we open up the oscillator, the circuit that makes the radio frequency in the first place. There are plenty of exam calculations here, and we will work through each one.
Roadmap
From transmitter to receiver Four parts, in the order a signal meets them, but starting with the journey itself:
1 · Propagation Attenuation; surface, space and sky waves ; the ionosphere; skip and dead space; HF frequency choice.
2 · Modulation Putting information on a carrier: keyed, AM, SSB, FM, phase and pulse ; emission designators.
3 · Aerials Dipole and Marconi lengths, feeders, polar diagrams, directivity and radar reflectors.
4 · Oscillators Making the RF: LC and crystal oscillators, resonance, selectivity, CRT, klystron and magnetron.
Chapter 20 · Radio Propagation
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is a long chapter, so here is the map. Part one is propagation, meaning how radio waves actually travel. We start with why signals weaken with distance, then the three paths that matter to aviation, the surface wave, the space wave and the sky wave, and how the ionosphere decides where sky waves come back down. That leads to choosing an HF frequency on an ocean crossing. Part two is modulation, the ways speech and data are put onto a carrier wave. Part three is aerials: how long they should be, what their radiation patterns look like, and how radar reflectors make narrow beams. Part four is oscillators, the circuits that generate the radio frequency in the first place, with resonance, crystals and the microwave tubes used in radar. Every part has exam calculations, and we will work through them.
Propagation
Why signals weaken: attenuation Attenuation = loss of signal strength with distance: absorption plus spreading Absorption by air, water, dust, vegetation and the ground rises with frequency; big above about 1000 MHz Inverse square law : power per m² ∝ 1 / R², so double the range needs four times the power Static (weather, people, the receiver itself) is worst at low frequencies ; quality is the signal-to-noise ratio A more sensitive receiver (less internal noise) hears weaker signals; costly Directivity : a narrow beam gives more range for the same power, but only along the beamtransmitter at R: 4 W on each 1 m² at 2R: the same power covers 4 m² → 1 W per m² 0 1 2 3 4 0 1 2 3 4 range (multiples of R) W per m² 4.00 1.00 0.44 0.25 P ∝ 1 / R²
Chapter 20 · Radio Propagation
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Signal strength falls as a wave travels outward, and the general name for this loss is attenuation. It has two parts. The first is absorption: air molecules, water vapour, dust, rain, vegetation and the earth itself all soak up some energy, and apart from the ionosphere this absorption gets worse as frequency rises, becoming very significant above about one thousand megahertz. The second is spreading. Energy from an aerial spreads over the surface of a growing sphere, so if four watts fall on each square metre at one range, at twice that range the same power covers four square metres and you get one watt per square metre. That is the inverse square law, and it means that doubling the range needs four times the power. Static noise from weather and from the equipment itself is worst at low frequencies. A quieter, more sensitive receiver, or concentrating the power into a beam, also extends the usable range.
Propagation
The propagation paths, band by band Surface wave exists from about 20 kHz to 50 MHz (used 20 kHz–2 MHz); sky wave 20 kHz–50 MHz (used 2–30 MHz); space wave from VHF upward.
Band Main path used Also present Typical use VLF Ducting (earth–ionosphere waveguide) — none in civil aviation (not examined) LF Surface wave (sky wave, at night) NDB MF Surface wave (sky wave, at night) NDB, some communications HF Sky wave (surface wave, short range) long-range voice VHF Space wave (line of sight) — voice, VOR, ILS localiser UHF, SHF, EHF Space wave (line of sight) satellite paths through the ionosphere DME, SSR, GNSS, radar
Whatever the main path, a receiver that is in line of sight of the transmitter is receiving the space wave .
Chapter 20 · Radio Propagation
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the propagation paths, band by band. There are really five, of which four matter to us. Very low frequencies travel by ducting, trapped between the ground and the bottom of the ionosphere, but there are no civil aviation systems there, so it is not examined. Low and medium frequencies are used as surface waves, which follow the curve of the earth; they also produce sky waves, but mainly at night, and those are a nuisance rather than a help. High frequency is the sky wave band: signals are bent back down by the ionosphere to reach thousands of miles. From VHF upward we have the space wave, which travels in straight lines like light, so its range is line of sight. Satellite signals also use these higher frequencies and pass straight through the ionosphere. One last point: whatever the main path, if the receiver is in line of sight, it is the space wave that is being received.
Surface wave
The surface wave bends round the earth Exists from about 20 kHz to 50 MHz ; the main path for LF and lower MF (30 kHz–2 MHz) The base of the wave is slowed by the ground , so the front tilts and follows the curve: diffraction Range falls as frequency rises : negligible above HF Better over sea than land: sea water conducts well, so losses are lowerMust be vertically polarised ; horizontal polarisation dies out very quickly The foot of each wavefront drags in the ground, so the front leans forward and follows the curve (diffraction) surface wave Best: low frequency, over sea, vertical polarisation
Chapter 20 · Radio Propagation
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The surface wave travels along the ground, following the curve of the earth well beyond the horizon. It exists from about twenty kilohertz to about fifty megahertz, and it is the main path used in the low frequency band and the lower part of the medium band, roughly thirty kilohertz to two megahertz. Why does it bend? The part of the wave touching the ground is slowed down by it, so each wavefront leans forward and follows the surface, a process called diffraction. Three things decide how far it goes. Frequency: the higher the frequency, the greater the surface losses, so the range drops, and above HF there is effectively no surface wave. The surface: sea water is a good conductor, so ranges over sea are greater than over land. And polarisation: a horizontally polarised surface wave is attenuated very quickly, so surface wave systems use vertical aerials. The best surface wave is low frequency, over sea, vertically polarised.
Surface wave
Surface wave range and coastal refraction Around 300 kHz: range ≈ 3 √P over sea and 2 √P over land (nm, P in watts) 10 kW: √10 000 = 100, so about 300 nm sea, 200 nm land 1600 W: √1600 = 40, so 120 nm over sea Range ∝ √P: double the range needs four times the power again Coastal refraction : crossing from land to sea the wave speeds up and bends towards the coast (an ADF error)0 100 200 300 400 0 5 10 15 20 transmitter power (kW) range (nm) 300 nm sea 200 nm land LAND SEA coast faster over sea: bends towards the coast
Chapter 20 · Radio Propagation
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
For a medium frequency transmitter around three hundred kilohertz there is a handy rule for surface wave range. Over the sea the range in nautical miles is about three times the square root of the power in watts, and over land it is about two times the square root. So a ten kilowatt beacon: the square root of ten thousand is one hundred, giving about three hundred nautical miles over sea and two hundred over land. A sixteen hundred watt beacon: the square root is forty, so about one hundred and twenty nautical miles over the sea. Notice the square root: again, to double the range you need four times the power. There is one more effect. Because the wave travels faster over sea than over land, the part of a wavefront that reaches the coast first speeds up, and the wave bends towards the coastline. This is coastal refraction, and you will meet it again as an ADF error.
Space wave
The space wave: line of sight From VHF upward , waves behave like light: direct wave plus a ground-reflected wave Slight atmospheric refraction carries them a little beyond the visual horizon Range (nm) = 1.23 × (√HTX + √HRX ) , heights in feetExample: 1600 ft and 1024 ft → 1.23 × (40 + 32) = 88.6 nm Below the line of sight, no amount of power will get a signal through radio horizon direct wave ground-reflected wave below the horizon: nothing received range (nm) = 1.23 × (√HTX + √HRX ) heights in feet
Chapter 20 · Radio Propagation
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
At VHF and above, radio waves start to behave like light. The space wave consists of a direct wave, travelling in a straight line from transmitter to receiver, and a wave reflected off the ground on the way. Just as light has a visual horizon, radio has a radio horizon. A little atmospheric refraction bends the waves gently towards the earth, carrying them slightly beyond the geometric horizon, and for the exam the line-of-sight range in nautical miles is one point two three times the sum of the square roots of the transmitter and receiver heights in feet. For example, a receiver at sixteen hundred feet and a transmitter at one thousand and twenty-four feet: forty plus thirty-two is seventy-two, times one point two three is about eighty-eight point six nautical miles. In the scene, the high aircraft is in line of sight. The low aircraft beyond the radio horizon receives nothing at all, and extra power will not help.
Space wave
Line-of-sight range: worked examples Question Working Answer Receiver 1600 ft, transmitter 1024 ft 1.23 × (√1600 + √1024) = 1.23 × (40 + 32) 88.6 nm Aircraft 2500 ft, VHF station 196 ft 1.23 × (50 + 14) = 1.23 × 64 78.7 nm (≈ 80 nm)Aircraft 10 000 ft, station at sea level 1.23 × √10 000 = 1.23 × 100 123 nm Aircraft FL 360 (36 000 ft), station 100 ft 1.23 × (189.7 + 10) 246 nm Radar at 1600 ft; lowest height to be seen at 200 nm? 200 / 1.23 = 162.6; 162.6 − 40 = 122.6; 122.6² ≈ 15 000 ft Double the power of a VHF station Line of sight is set by heights, not power no gain beyond the horizon
Work in feet and nautical miles. To find a height, divide the range by 1.23, subtract the known root, then square.
Chapter 20 · Radio Propagation
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us practise the line-of-sight formula. An aircraft at two thousand five hundred feet and a station at one hundred and ninety-six feet: the roots are fifty and fourteen, sixty-four times one point two three is about seventy-nine, so roughly eighty nautical miles. An aircraft at ten thousand feet talking to a station at sea level: the root of ten thousand is one hundred, giving one hundred and twenty-three nautical miles. At thirty-six thousand feet, with a station one hundred feet up, the range is about two hundred and forty-six nautical miles. Now work it backwards. A radar at sixteen hundred feet must see an aircraft at two hundred nautical miles. Divide two hundred by one point two three to get one hundred and sixty-two point six, take away the radar root of forty to leave one hundred and twenty-two point six, and square it: about fifteen thousand feet. And remember, more power does nothing beyond the horizon.
The ionosphere
How the ionosphere forms and varies Extends from about 60 km up to around 1500 km; pressure there is tiny Solar ultraviolet knocks electrons off atoms: free electrons and positive ions Electrons keep recombining, so ionisation is highest soon after midday (~1400 local) and lowest just before sunrise Higher in summer and at low latitudes ; solar flares give sudden extreme ionisation It forms layers , not a smooth increase; dawn and dusk are unsettled and disturb HF and ADF 0 100 200 300 400 height (km) D E F1 F2 ionisation (schematic, by day) → base ≈ 60 km UV and shorter waves knock electrons off atoms: free e⁻ + positive ions Ionisation is highest • soon after midday (~1400 LT) • in summer • at low latitudes Lowest • just before sunrise Solar flares: sudden extreme ionisation
Chapter 20 · Radio Propagation
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ionosphere starts about sixty kilometres up and extends to the edge of the atmosphere. The air there is very thin, so atoms are far apart. Ultraviolet and shorter-wave radiation from the sun knocks electrons out of these atoms, leaving free electrons and positively charged ions; that is ionisation. At the same time electrons keep recombining with ions, so the ionisation level is a balance. It peaks soon after midday, around fourteen hundred local time, and is lowest just before sunrise. It is higher in summer than in winter, and higher at low latitudes, because the sun is stronger there. Solar flares can produce sudden, extreme ionisation that disrupts radio and can even force satellites to shut down. Because the upper air is not mixed, the ionisation forms distinct layers rather than increasing smoothly with height. And around dawn and dusk the layers are changing, so sky wave systems suffer interference.
The ionosphere
The D, E and F layers, by day and by night D region ~75 km : forms at sunrise, gone after sunset ; absorbs LF/MF by dayE layer ~125 km : present day and night; lower by day, higher at night F layer ~225 km : splits into F1 and F2 by day and rejoins at nightF2 rises in summer, to 400 km or more , and is lower in winterIonisation is greatest at the centre of each layer DAY D E F1 F2 ~75 km ~125 km ~225 km to 400+ NIGHT E F D gone after sunset E weaker and higher F1 and F2 merge
Chapter 20 · Radio Propagation
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ionosphere has three main layers. The lowest is the D region, on average about seventy-five kilometres up. It is fairly diffuse, it forms at sunrise and, for practical purposes, it disappears at sunset; by day it absorbs low and medium frequency energy. Next is the E layer, about one hundred and twenty-five kilometres up, which is there day and night; it comes down at sunrise and goes back up after sunset. Highest is the F layer, about two hundred and twenty-five kilometres up. By day it splits into two, F one and F two. F two depends on the season, rising in summer to four hundred kilometres or more. Watch the scene at sunset: the D region fades away, the E layer drifts upward, and the F one and F two layers rejoin into a single F layer for the night. Within each layer, ionisation is strongest at the centre.
Sky wave
Critical angle, skip distance and dead space skip distance ← dead space surface wave first returning sky wave steeper rays escape ionised layer critical angle A wave entering a layer at an angle is refracted away from the normal; if it turns horizontal before the layer’s centre it comes back down.
Chapter 20 · Radio Propagation
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how the sky wave works. Ionisation increases towards the centre of a layer, so a wave entering at an angle is refracted progressively away from the vertical. If it has been turned to the horizontal before it reaches the centre of the layer, it keeps bending and comes back to earth as a sky wave. Start with a ray going straight up from the transmitter; at HF it passes through and escapes. As you tilt the ray further from the vertical, you reach an angle at which it is just turned back. This is the first returning sky wave, and its angle, measured from the vertical, is the critical angle. The distance from the transmitter to where it lands is the skip distance. Meanwhile the surface wave dies out close to the transmitter. Between the end of the surface wave and the first returning sky wave nothing can be received; that gap is the dead space.
Sky wave
What changes the skip distance Change Critical angle Skip distance Dead space Ionisation increases (day, summer, low latitude) smaller shorter smaller Ionisation decreases (night, winter) larger longer larger Frequency increases larger longer larger (surface wave also shorter) Frequency decreases smaller shorter smaller Refracting layer higher (e.g. F instead of E) — longer larger
Rule of thumb: E layer refracts up to about 2 MHz, F layers about 2–50 MHz. Above 50 MHz sky wave only appears in abnormal solar conditions.
Chapter 20 · Radio Propagation
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Three things change the skip distance, and this table is a favourite exam topic. First, ionisation. More ionisation means more refraction, so waves turn back at a smaller critical angle, and the skip distance and dead space both shrink. Less ionisation, at night for example, does the opposite. Second, frequency. For a given ionisation, higher frequencies are refracted less, so the critical angle grows and the skip distance and dead space grow. Higher frequency also shortens the surface wave, so the dead space widens from both ends. Lower frequency brings everything closer again. Third, the height of the refracting layer: the higher the layer, the longer the skip, so refraction at the F layers gives greater ranges than at the E layer. As a general guide, frequencies up to about two megahertz are turned back by the E layer and two to fifty megahertz by the F layers. Above fifty megahertz, sky waves are rare.
Sky wave
LF and MF sky waves at night By day the D region absorbs sky waves below about 2 MHz : only the surface wave arrives At night the D region has gone, so LF/MF sky waves are refracted by the E layer They return at fairly short range and mix with the surface wave Result: fading and bearing errors: the night effect on ADF , and interference between stations So LF/MF sky waves are not reliable for continuous long-range use DAY E surface wave D ✕ D layer absorbs LF/MF sky waves by day surface wave only: steady NDB signal NIGHT E surface wave no D layer: sky wave from E returns at short range mixes with the surface wave: fading, ADF night effect
Chapter 20 · Radio Propagation
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Low and medium frequencies are used as surface waves, so why do we care about their sky waves? Because of what happens at night. By day, the D region absorbs radio energy below about two megahertz, so any LF or MF energy heading upward is soaked up, and only the steady surface wave reaches a receiver. After sunset the D region disappears. Now the sky wave reaches the E layer, is refracted back, and lands at a fairly short range, inside the area that the beacon is meant to serve by surface wave. The receiver hears both waves at once, with different strengths and phases, so the signal fades and the bearing wanders. This is night effect, and it affects the ADF in particular, as well as broadcast stations interfering with each other. It also means LF and MF sky waves cannot be relied on for continuous long-range work, because they come and go with the sun.
Sky wave
How far a sky wave can reach Longest single hop: the ray leaves and arrives tangential to the earth E layer (~125 km): about 1350 nm ; F layer: about 2200 nm (exam figures) Ranges change as the layer heights change Multi-hop : the earth reflects the sky wave back up; HF can reach about half-way round the world VLF (below ~20 kHz): earth and ionosphere form a waveguide (ducting) with little lossE layer ~125 km: ≈ 1350 nm F layer: ≈ 2200 nm Longest single hop: the ray leaves and arrives tangential to the earth Multi-hop: the ground reflects it up again, so HF can reach half-way round the world
Chapter 20 · Radio Propagation
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
How far can one sky wave hop go? The longest hop is when the ray leaves the transmitter just skimming the horizon and arrives at the receiver the same way, tangential to the earth at both ends. With the E layer at about one hundred and twenty-five kilometres, simple geometry gives about one thousand three hundred and fifty nautical miles. Refraction from the higher F layer gives about two thousand two hundred nautical miles; those are the figures to use in the exam, but remember they change as the layers rise and fall. Longer ranges come from multi-hop propagation: the returning sky wave reflects off the earth, goes back up, and is refracted down again, so HF can reach around half the world. Finally, very low frequencies, below about twenty kilohertz, have wavelengths comparable to the height of the ionosphere, and the earth and the bottom of the ionosphere act as a waveguide, ducting the signal round the globe.
Space wave
Super-refraction, sub-refraction and ducting Affects VHF and above. Super-refraction : more downward bending, range up to +40% Caused by humidity falling with height, temperature falling slower than standard, high pressure , warm air over a cool surface Duct : a low inversion of warm dry air over cool moist air traps VHF/UHF, giving exceptional ranges Common where deserts border the sea (Mediterranean, Caribbean), and under winter anticyclones Sub-refraction (rarer): range down by up to 20% ; humidity rising with height, steep lapse rate, low pressure , cold air over a warm surface sub-refraction: horizon up to 20% closer no refraction: geometric horizon standard atmosphere super-refraction: up to 40% further Dots: where each ray grazes the earth (its radio horizon) Duct: warm dry air (inversion) over cool moist air traps VHF/UHF between the layer and the surface cool moist layer
Chapter 20 · Radio Propagation
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The line-of-sight formula assumes a standard atmosphere. Sometimes, at VHF and above, the air bends waves more than usual; this is super-refraction, and it can stretch line-of-sight range by up to about forty per cent. It happens when humidity decreases with height, when temperature falls more slowly than standard, in fine weather under high pressure, and when warm air flows over a cooler surface. In the extreme case, a low-level inversion with warm dry air sitting on cool moist air forms a duct that traps the waves and carries them to exceptional ranges; that is when distant television stations suddenly interfere with local ones. Ducting is common where hot deserts border seas, such as the Mediterranean and the Caribbean, and under winter anticyclones. Sub-refraction is rarer and reduces range by up to twenty per cent. Its conditions are the opposites: humidity increasing with height, a steep lapse rate, poor weather with low pressure, and cold air over a warm surface.
HF communications
Choosing an HF frequency Over oceans, without satcom, sky wave is the only practical long-range voice path MUF (maximum usable frequency) for a range = the frequency whose first returning sky wave lands thereUse the OWF = 0.85 × MUF , so a dip in ionisation does not leave you in the skip zone Night : lower ionisation → roughly half the day frequency Longer range → higher frequency ; short range → lower frequencySELCAL : a 4-letter code (e.g. ABCD) chimes the crew, so no need to listen to HF noiseMUF and OWF for one range (example) 20 MHz Day MUF 17 MHz Day OWF 10 MHz Night MUF 8.5 MHz Night OWF OWF = 0.85 × MUF night ≈ ½ day frequency longer range → higher frequency
Chapter 20 · Radio Propagation
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Over oceans, unless you have satellite communications, the sky wave is the only practical way to talk over thousands of miles; a surface wave would need very low frequencies, heavy equipment and lots of static. So which HF frequency? For any range, the maximum usable frequency is the one whose first returning sky wave lands exactly at that range. It takes the shortest path through the ionosphere, so it has the least attenuation and noise. But if ionisation dipped, the skip would lengthen and you would lose contact, so we use a slightly lower optimum working frequency, about nought point eight five times the maximum usable frequency. At night ionisation is lower, so you need a lower frequency, roughly half the daytime one. And because skip grows with frequency, longer ranges need higher frequencies. HF is noisy and tiring to monitor, so aircraft use SELCAL: ATC sends your four-letter code and a chime alerts you.
HF communications
The mid-ocean HF problem Mid-Atlantic at SUNRISE USA / Gander UK / Shanwick 6 MHz refracts in night air 12 MHz refracts in day air The sun rises in the east first and sets in the east first. Mid-Atlantic at SUNSET USA / Gander UK / Shanwick 12 MHz refracts in day air 6 MHz refracts in night air The sun rises in the east first and sets in the east first. The wave is refracted half-way to each station. Where that midpoint is in daylight, use the higher frequency; in darkness, the lower .
Chapter 20 · Radio Propagation
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a classic exam problem. An aircraft is in the middle of the Atlantic at sunrise, talking to the UK on twelve megahertz. What frequency should it expect to use with the USA? Think about where each wave is refracted: roughly half-way between the aircraft and each station. The sun rises in the east first, so at sunrise the half-way point towards the UK is already in daylight, with high ionisation, which is why twelve megahertz works. The half-way point towards America is still in darkness, with low ionisation, so it needs a lower frequency, about half: six megahertz. Now reverse it. At sunset the sun has already set in the east, so the path to Shanwick in the UK refracts in night air and needs about six megahertz, while the path to Gander in Canada is still in daylight and needs about twelve. Always ask: is the midpoint in day or night?
Modulation
Keyed and amplitude modulation Modulation = adding information to a radio wave (the carrier)Keyed : switch the carrier on and off in Morse ; still used for some NDB identification AM : the amplitude of the RF follows the amplitude of the audio (AF)Positive audio raises the RF amplitude; negative audio lowers it A microphone first turns sound into an electrical audio signal Keyed (Morse "K": — · —) Audio frequency (AF) Radio frequency carrier (RF) Amplitude-modulated RF dashed envelope = the audio
Chapter 20 · Radio Propagation
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Modulation means adding information to a radio wave, which we call the carrier. The simplest way is keyed modulation: just switch the carrier on and off in long and short bursts, the dashes and dots of Morse code. The drawing shows the letter K, dash dot dash. Keyed modulation is still used by some non-directional beacons for their identification. For speech we need something smoother. A microphone turns sound into an electrical audio frequency signal, and in amplitude modulation the amplitude of the radio frequency carrier is made to follow the amplitude of that audio. Where the audio is positive, the carrier gets bigger; where it is negative, the carrier gets smaller. Look at the bottom trace: the dashed envelope traced by the peaks of the carrier is the audio itself. In the exam, remember that in AM the amplitude of the RF is changed by the amplitude of the AF, not by its frequency.
Modulation
Sidebands, bandwidth and single sideband Double sideband AM (A3E) 2179 kHz 2182 kHz 2185 kHz carrier 100 W LSB 25 W USB 25 W bandwidth 6 kHz = 2 × AF Single sideband, suppressed carrier (J3E) 2179 kHz 2182 kHz 2185 kHz USB: all the power carrier and LSB removed 3 kHz SSB advantages: twice as many channels , better signal-to-noise , less power (lighter equipment). HF voice is J3E; VHF voice is A3E.
Chapter 20 · Radio Propagation
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a carrier is amplitude modulated, new frequencies appear. Take a two thousand one hundred and eighty-two kilohertz carrier modulated with three kilohertz audio. The carrier stays where it is, but the audio appears twice: as an upper sideband up to two thousand one hundred and eighty-five kilohertz and a lower sideband down to two thousand one hundred and seventy-nine. So the bandwidth is six kilohertz, twice the audio frequency. Both sidebands carry the same information, and the carrier carries none, so only about a third of the power is doing useful work. Single sideband removes the carrier and one sideband and puts the power into the remaining one. That gives three big advantages: twice as many channels fit in the crowded HF band, the signal-to-noise ratio is better, so there is less interference and distortion from the ionosphere, and less power is needed, so the equipment is lighter. HF voice uses single sideband, designated J three E.
Modulation
FM, phase, pulse, and emission designators FM : the frequency of the RF is changed by the amplitude of the AF; the AF frequency sets the rate of changeFM broadcasting needs about 150 kHz bandwidth (AM: 9 kHz), so FM is used only at VHF and above; not used for aviation voice Phase modulation ; digital form is phase shift keying (0° = 0, 180° = 1), used in satellite navigation and MLSPulse modulation: radar, DME and dataDesignators: A3E VHF voice, J3E HF voice, N0NA1A / N0NA2A ADF, A9W VOR, A8W ILS, A2A markers, P0N DME Audio signal FM: frequency follows the audio amplitude Phase shift keying: 0° = 0, 180° = 1 0 1 1 0 1 Pulse: short bursts of RF (radar, DME, data)
Chapter 20 · Radio Propagation
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
In frequency modulation, the frequency of the carrier is changed by the amplitude of the audio. The louder the audio, the further the frequency swings; you can see the cycles crowding and spreading in the second trace. FM broadcasting needs about one hundred and fifty kilohertz of bandwidth, against nine kilohertz for AM, so FM is only practical at VHF and above, and it is not used for aviation voice. In phase modulation the carrier’s phase is shifted by the signal. Its digital form is phase shift keying, where for example no shift means zero and a one hundred and eighty degree shift means one; satellite navigation and microwave landing systems use it. Pulse modulation sends short bursts and is used by radar and DME. Finally, emission designators: A three E is VHF voice, J three E is HF voice, and the ADF designators N zero N A one A and two A are the most likely to be examined.
Aerials
Dipole and Marconi aerials, and feeders Half-wave dipole : fed at the centre, radiates at right angles to its lengthMarconi (quarter-wave) on a metal ground plane; the skin is the other half. Used on aircraft: low drag Waves are slower in metal (~95%): length = 0.95 × λ/2 or λ/4 . 125 MHz → λ 2.4 m → Marconi 57 cm Real VHF aerials (20–30 cm) are too short, so an aerial loading (tuning) unit matches them Feeders: wire (LF/MF), twin wire (HF/VHF), coaxial cable (UHF), waveguide (upper UHF and SHF; width ≈ λ/2) Half-wave dipole fed at centre λ/2 current Marconi (quarter-wave) fuselage skin = ground plane mirror image λ/4 125 MHz: λ = 300/125 = 2.4 m Marconi = 0.95 × 2.4 / 4 = 0.57 m (57 cm)
Chapter 20 · Radio Propagation
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two basic aerials do most of the work. The half-wave dipole is fed at its centre and radiates most strongly at right angles to its length, with nothing off its ends: the scene shows its doughnut-shaped radiation pattern. The Marconi, or quarter-wave aerial, stands on a metal surface that acts as the missing half of the dipole; on an aircraft that surface is the fuselage skin, and because it is short and neat it causes little drag. For best efficiency the length must suit the wavelength, but waves travel at only about ninety-five per cent of their free-space speed in metal, so the length is nought point nine five times a half or a quarter wavelength. At one hundred and twenty-five megahertz, the wavelength is two point four metres, so a Marconi aerial should be fifty-seven centimetres. Real aircraft aerials are shorter, so a loading unit electrically matches them. Feeders change with frequency: wire, then twin wire, coaxial cable, and finally waveguide.
Aerials
Polar diagrams and directivity A polar diagram joins points of equal signal strength around an aerial A vertical dipole is omnidirectional in plan; side-on it is a figure of eight, zero off the ends A reflector 5% longer, λ/4 behind, cancels the back signal; directors (shorter) in front sharpen the beam The price of directivity is sidelobes : unwanted transmission and reception (problems for SSR, ILS, radar) An ILS localiser uses a line of 16 or 24 aerials; an ADF loop gives a figure of eight with two nulls Dipole (plan, aerial vertical) omnidirectional Dipole (side view) nothing off the ends Yagi: reflector + directors main beam + sidelobes ADF loop two sharp nulls null null
Chapter 20 · Radio Propagation
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
A polar diagram is a line joining all the points around an aerial where the signal strength is the same, so it shows the shape of the radiation pattern. A vertical dipole, seen from above, radiates equally in all directions, while seen from the side it is a figure of eight with nothing off its ends. To make an aerial directional, add parasitic elements. A rod about five per cent longer than the aerial, placed a quarter of a wavelength behind it, acts as a reflector and cancels radiation to the rear. Shorter rods in front, called directors, focus the energy into a stronger forward beam. That is the familiar television aerial, called a Yagi, shown in the scene. Directivity has a price: sidelobes, which send and receive in unwanted directions and cause real problems for secondary radar, ILS and primary radar. The ILS localiser uses a long line of aerials, and the ADF loop has two sharp nulls.
Aerials
Radar aerials: dishes and slotted arrays Radar uses UHF and SHF: the energy arrives by waveguide , whose open end is the aerial Placed at the focus of a parabolic reflector to make a narrow beam, but with some spread and sidelobes Beamwidth (°) = 70 λ / D : narrow beam needs a big dish or short wavelength Example: λ 3.2 cm, D 76 cm → 70 × 3.2 / 76 ≈ 3° Slotted (phased) array : narrower beam, smaller sidelobes, less power, narrower pulse, better resolutionfeed at focus main beam sidelobes parabolic reflector flat-plate slotted array narrower beam, smaller sidelobes beamwidth = 70 λ / D 3.2 cm, 76 cm dish → about 3°
Chapter 20 · Radio Propagation
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Radars work in the UHF and SHF bands, where the energy is carried by a waveguide and the open end of the waveguide is effectively the aerial. To make a beam, that open end sits at the focus of a parabolic reflector. Ideally the dish would make a pencil-thin beam, but the waveguide opening is not a perfect point, so the beam spreads a little, and uneven reflection creates sidelobes strong enough to give false echoes. Beamwidth in degrees is seventy times the wavelength divided by the dish diameter, in the same units. So a narrow beam needs a large dish, a short wavelength, or both. A weather radar on three point two centimetres with a seventy-six centimetre dish gives seventy times three point two over seventy-six, about three degrees. Modern weather radars use a flat slotted array instead: a narrower beam, smaller sidelobes, less power for the same range, a narrower pulse and better resolution.
Oscillators
Oscillators and resonance An oscillator makes an AC sine wave from a DC supply , with no input signal Parts: amplifier , frequency-determining circuit (LC, RC or crystal), positive feedback Used for the transmitter carrier , and in receivers to make an intermediate frequency (superheterodyne) XL rises with f, XC falls: they are equal at resonance, f₀ = 1 / (2π√LC) Parallel LC at f₀: XL = XC , a large circulating current in the tank, maximum impedance Amplifier Frequency- determining (LC) Positive feedback DC supply in, AC out: no input signal 0 2 4 6 0 25 50 75 100 frequency (kHz) reactance (Ω) f₀ = 45 kHz XL XC L = 5 µH, C = 2.5 µF: f₀ = 1 / (2π√LC)
Chapter 20 · Radio Propagation
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every transmitter needs a source of radio frequency, and that is the oscillator. It produces an AC sine wave from nothing but a DC supply, with no input signal. It has three parts: an amplifier, a circuit that sets the frequency, which may be inductance and capacitance, resistance and capacitance, or a crystal, and a positive feedback path that returns some of the output to the input in step, keeping it going. Receivers use oscillators too, mixing their output with the incoming signal to make a lower intermediate frequency that is easier to amplify; that is the superheterodyne principle. Now resonance. Inductive reactance rises with frequency and capacitive reactance falls, so at one frequency they are equal. That is the resonant frequency, one over two pi root L C. With five microhenries and two point five microfarads it is about forty-five kilohertz. In a parallel tank at resonance, a large current circulates between the coil and the capacitor.
Oscillators
LC and crystal oscillators, and selectivity Tuned-collector LC oscillator +V (DC) 0 V SW1 C1 L1 tank circuit TR1 R1 L2 C2 L1 → L2 coupling: positive feedback output Crystal-controlled oscillator Amplifier quartz crystal (XTAL) • sets the frequency AND gives the feedback • very stable, very narrow bandwidth • frequency fixed by crystal thickness Bandwidth and selectivity A: narrow, selective B: wide 0.707: −3 dB f₀ (bandwidth = f₂ − f₁ between the −3 dB points) Change C1 (or L1) to change the frequency. A quartz crystal is far more stable but not easily retuned. Narrow bandwidth = high selectivity .
Chapter 20 · Radio Propagation
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the left is a tuned-collector oscillator. The tank circuit, C one in parallel with L one, sits in the collector of transistor T R one and sets the frequency. The transistor is the amplifier: it makes up for the losses in the circuit. Winding L two is coupled to L one like a transformer and feeds part of the signal back to the base in step, which is the positive feedback, rather like flicking a spinning top in the right direction at the right moment. R one and C two simply set and decouple the base bias. Close switch S W one and the tank is shocked into oscillation. To vary the frequency, make C one a variable capacitor. In the middle, a crystal oscillator. A quartz crystal vibrates at a frequency set by its thickness, the piezo-electric effect, and it provides both the frequency control and the feedback; it is very stable but hard to retune. On the right, the narrower the response between the half-power points, the more selective the circuit.
Oscillators
CRT displays and microwave oscillators CRT : heated cathode emits electrons; the grid (more negative = dimmer, then cut-off) sets brillianceAnodes accelerate and focus ; plates (electrostatic) or coils (electromagnetic) deflect ; the screen glows. Colour: red, green and blue beams Above about 1 GHz transistor circuits fail: microwave oscillators use resonant cavities (about λ/2 across) Klystron : one cavity, electron gun, reflector feedback; low power , radar receiversMagnetron : cavities in a copper block, a strong magnet makes electrons orbit; frequency set by cavity size ; high power , radar transmitterscathode grid anodes Y-plates X-plates screen grid more −: dimmer (cut-off) 2nd anode: focus plates / coils: deflection Magnetron (high power) Magnetron cavities in a copper anode block; strong magnet makes electrons orbit; frequency set by cavity size → radar transmitters Klystron one cavity, electron gun, reflector; low power → radar receivers
Chapter 20 · Radio Propagation
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more devices complete the picture. The cathode ray tube was the classic radar and television display. A heated cathode emits electrons. The grid around it is kept negative; make it more negative and fewer electrons get through, so the picture dims, until the beam is cut off altogether. A set of anodes accelerates and focuses the beam, and deflection plates or coils steer it across a fluorescent screen, which glows; colour tubes use red, green and blue beams. Above about one gigahertz, ordinary transistor oscillators stop working, so microwave oscillators use resonant cavities, about half a wavelength across. The klystron has one cavity, an electron gun and a negative reflector that sends electrons back through the cavity to sustain oscillation; it is a low-power oscillator for radar receivers. The magnetron has several cavities cut in a copper block inside a strong magnet; its frequency is set by the size of the cavities, and it produces the high-power pulses for radar transmitters.
Summary
Radio propagation in one page Attenuation Absorption (worse above ~1 GHz) + inverse square: 2 × range = 4 × power. Static worst at LF.
Surface wave LF/MF. Diffraction. Better over sea, vertical polarisation, low frequency. 3√P sea, 2√P land. Coastal refraction.
Space wave VHF up. Line of sight: 1.23 (√H₁ + √H₂). Super-refraction +40%, sub −20%, ducts.
Ionosphere D 75 km (day only), E 125 km, F 225 km (F1/F2 by day). Max ~1400 LT, min before dawn.
Sky wave More ionisation → shorter skip. Higher f or higher layer → longer skip, bigger dead space. E 1350 nm, F 2200 nm.
HF OWF = 0.85 MUF. Night ≈ ½ day frequency. Midpoint in day → higher f. SELCAL 4 letters.
Modulation AM: RF amplitude by AF amplitude; BW = 2 × AF. SSB (J3E): more channels, better S/N, less power. FM: RF frequency by AF amplitude.
Aerials and oscillators 0.95 × λ/2 or λ/4. Beamwidth 70λ/D. f₀ = 1/(2π√LC). Crystal stable. Magnetron = radar Tx; klystron = Rx.
Chapter 20 · Radio Propagation
27
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Signals weaken by absorption, which grows above about a gigahertz, and by the inverse square law, so doubling range takes four times the power. The surface wave serves LF and MF; it goes furthest at low frequency, over sea, vertically polarised, roughly three root P over sea and two root P over land. The space wave serves VHF and above, limited to one point two three times the sum of the root heights, stretched by super-refraction and cut by sub-refraction. The ionosphere has the D, E and F layers; more ionisation shortens the skip, while higher frequency or a higher layer lengthens it. For HF, use about nought point eight five of the maximum usable frequency, about half the frequency at night, and check whether the midpoint is in daylight. AM bandwidth is twice the audio, and remember SSB’s three advantages. For aerials, lengths use nought point nine five, beamwidth is seventy lambda over D, and resonance is one over two pi root L C.