Electrics · Chapter 17
Semiconductors From silicon atoms to transistors: how doping makes N-type and P-type material, how a PN junction becomes a diode, and how a transistor lets a small current control a large one.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter seventeen is about semiconductors, the materials inside every diode, transistor and computer chip on the aircraft. Transformer rectifier units, static inverters, generator control units and all the avionics depend on them. We start with the atom and see why some materials conduct and others do not. Then we add tiny amounts of impurity to silicon to make N-type and P-type material, join the two to make a diode that lets current through one way only, and finally sandwich three layers to make the transistor, the switch and amplifier that made modern electronics possible.
Roadmap
Semiconductors: the plan for this lesson Solid-state devices do the work of switches, valves and amplifiers with no moving parts. To understand them we start with the atom.
1 · Materials Atoms, free electrons, conductors and insulators, and the silicon crystal.
2 · Doping Donors and acceptors, N-type and P-type material, electrons and holes.
3 · The junction Depletion layer, barrier potential, forward and reverse bias, diodes and rectifiers.
4 · The transistor NPN and PNP, current gain, switch and amplifier, integrated circuits.
Chapter 17 · Semiconductors
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our plan. Modern aircraft are full of solid state devices: they switch, rectify and amplify with no moving parts, no heated filaments, and very little weight. In part one we look at materials. We revisit the atom, see what makes a conductor or an insulator, and meet the silicon crystal that sits in between. In part two we dope the crystal, adding tiny amounts of carefully chosen impurity to make N-type and P-type material, and meet the two kinds of charge carrier, electrons and holes. In part three we join P and N together, discover the depletion layer, and see how the junction passes current one way only, which gives us the diode and the rectifier. In part four we build the transistor, see how a tiny base current controls a large collector current, and finish with the integrated circuit.
Introduction
Why a pilot needs semiconductors Transistorisation and miniaturisation put more computing power in a pocket calculator than early spacecraft carried.
Rectifiers Diodes in transformer rectifier units turn 115 V AC into 28 V DC for the DC busbars.
Static inverters Transistors switch DC to make AC for essential instruments when the generators fail.
Control units Generator and bus power control units sense, compare and switch with solid-state circuits.
Avionics Flight management, autopilot, EFIS and warning computers are built from millions of transistors.
Chapter 17 · Semiconductors
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why should a pilot care about semiconductors? Because almost every electrical system you will meet relies on them. The transformer rectifier units that turn one hundred and fifteen volts AC into twenty-eight volts DC are built around banks of diodes. The static inverter that keeps the essential instruments alive on battery power uses transistors as fast switches. Generator control units and bus power control units sense voltage, frequency and current and switch contactors using solid state circuits. And the avionics, flight management, autopilot, displays and warning systems, are computers containing millions of transistors on a few chips. Transistorisation and miniaturisation are why a cheap calculator now holds more computing power than early spacecraft did. Understanding how these devices work, and how they fail, makes you a better operator of the systems built from them.
Part 1 · Materials
The atom and its valence electrons Nucleus : positive protons and neutral neutrons; electrons (−) orbit in shellsA neutral atom has equal numbers of protons and electrons Outer-shell (valence ) electrons are the least tightly held Valence electrons form the bonds between atoms and can become free electrons Silicon (14 electrons) and germanium (32) both have 4 valence electrons − − − − − − − − − − − − − − 14 p 14 n Silicon atom Nucleus 14 protons (+) and neutrons Inner shells 2 + 8 electrons, held tightly Valence shell 4 electrons: these form the bonds and carry current Germanium: 32 electrons, also 4 valence (2 + 8 + 18 + 4)
Chapter 17 · Semiconductors
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us start with the atom. At the centre is the nucleus, made of protons, which carry a positive charge, and neutrons, which carry none. Around it, negative electrons orbit in shells. A neutral atom has the same number of electrons as protons, so the charges balance. The simplest atom, hydrogen, has just one proton and one electron. Electrons in the inner shells are held tightly, but those in the outermost shell, the valence electrons, are held much more loosely. They are the ones that form bonds with neighbouring atoms, and they are the ones that can break away and wander through the material as free electrons, which is what an electric current is. The drawing shows silicon. It has fourteen electrons: two in the first shell, eight in the second, and four in the valence shell. Germanium, the other classic semiconductor, also has four valence electrons.
Part 1 · Materials
Conductors, insulators and semiconductors Conductors (silver, copper, gold): huge numbers of free electrons , low resistivityInsulators (mica, glass): valence electrons locked in bonds, few free electrons Semiconductors (silicon, germanium): in between; at room temperature a few bonds breakPure semiconductors are closer to insulators than to conductors An e.m.f. across a semiconductor gives an intermediate current METALS SEMICONDUCTORS INSULATORS 10-8 10-4 100 104 108 1012 1016 resistivity, ohm-metres (log scale: each mark ×10 000) Silver, copper, gold Germanium Silicon Glass Mica Free electrons: many → few Pure semiconductors sit between the two extremes
Chapter 17 · Semiconductors
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whether a material conducts depends on how many free electrons it has. In a metal such as silver, copper or gold, the valence electrons are not tied to any one atom; they form a sea of free electrons shared by the whole lattice, so current flows easily and the resistivity is very low. In an insulator such as mica or glass, the valence electrons are locked into strong bonds and there are almost no free electrons, so the resistivity is enormous. Semiconductors such as silicon and germanium sit between the two. Their valence electrons are held in covalent bonds, but at normal temperatures a few bonds break, so there are some free electrons. Apply an e.m.f. and you get an intermediate current: more than through an insulator, far less than through a conductor. Look at the scale: each mark is ten thousand times the last, and pure silicon is much closer to the insulator end.
Part 1 · Materials
The silicon crystal: covalent bonds Silicon atoms arrange themselves in a regular crystal lattice Each atom shares one valence electron with each of 4 neighbours A shared pair is a covalent bond ; each atom now "sees" 8 outer electrons At very low temperature every electron is bound: a perfect insulator Heat breaks a few bonds: an electron-hole pair appears Si Si Si Si Si Si Si Si Si Si Si Si each bond = a shared pair of valence electrons (covalent)
Chapter 17 · Semiconductors
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a crystal, silicon atoms arrange themselves in a regular lattice, each one equally spaced from its neighbours. Each silicon atom has four valence electrons, and it shares one with each of its four neighbours. Every bond between two atoms is therefore a shared pair of electrons, which we call a covalent bond. The scene shows the lattice flattened out so that you can see the pairs, drawn in blue, sitting on each bond. With all its bonds made, each atom effectively sees eight electrons in its outer shell, which is a very stable arrangement. At a very low temperature every electron is locked into a bond, and pure silicon is an insulator. But add some heat. Watch: one electron gains enough energy to break free. It can now drift through the crystal and carry current, and it leaves behind a gap in the bond, called a hole. Heat creates electrons and holes in pairs.
Part 1 · Materials
Temperature: semiconductors go the other way In a metal , resistance rises with temperature: atoms vibrate and impede the electrons In a pure semiconductor , heat frees more electron-hole pairs, so resistance falls This is a negative temperature coefficient (NTC) Used on purpose in thermistors for temperature sensing A nuisance in transistors: heat raises leakage and can cause thermal runaway ×0.001 ×0.01 ×0.1 ×1 ×10 ×100 ×1000 -50 0 50 100 150 temperature, °C resistance relative to 20 °C (log scale) copper: rises slowly pure silicon: falls steeply Heat frees electrons in a semiconductor: negative temperature coefficient
Chapter 17 · Semiconductors
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Temperature affects semiconductors in the opposite way to metals. In a metal there are already plenty of free electrons; heating it simply makes the atoms vibrate harder and get in the way, so resistance rises slowly with temperature, as the copper line shows. In a pure semiconductor the number of free carriers is what limits conduction, and heat breaks more covalent bonds, freeing more electron-hole pairs. So the resistance falls, and it falls steeply; for pure silicon, by roughly a factor of a thousand over this temperature range. We call this a negative temperature coefficient. It is put to good use in thermistors, which sense temperature in many aircraft systems. But in transistors and diodes it is a nuisance: as a device warms up its leakage current rises, which can warm it further, and without proper cooling this can lead to thermal runaway.
Part 2 · Doping
Doping: adding controlled impurities Pure silicon conducts poorly; doping adds a controlled impurity to improve it Doping ratio: about 1 impurity atom per 108 silicon atoms Group V donors (phosphorus, arsenic, antimony): 5 valence electrons → N-type Group III acceptors (boron, aluminium, gallium, indium): 3 valence electrons → P-type The crystal stays electrically neutral either way Group III 3 valence B boron Al aluminium Ga gallium In indium ACCEPTORS → P-type Group IV 4 valence C carbon Si silicon Ge germanium the base crystal Group V 5 valence N nitrogen P phosphorus As arsenic Sb antimony DONORS → N-type about 1 impurity atom per 10⁸ silicon atoms
Chapter 17 · Semiconductors
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pure silicon has too few free carriers to be useful, so we improve its conductivity in a controlled way by adding impurity atoms. This is called doping. The amounts are tiny: roughly one impurity atom for every hundred million silicon atoms. The choice of impurity decides what we get. Elements from group five of the periodic table, such as phosphorus, arsenic and antimony, have five valence electrons. They donate a spare electron to the crystal, so they are called donors, and they make N-type material. Elements from group three, such as boron, aluminium, gallium and indium, have only three valence electrons. They accept an electron from the crystal, so they are called acceptors, and they make P-type material. Remember one important point: every impurity atom is itself neutral, so doped material, whether N-type or P-type, carries no overall electric charge.
Part 2 · Doping
N-type material: a spare electron An arsenic (or antimony) atom takes a silicon atom's place in the lattice Four of its five valence electrons form covalent bonds The fifth has no bond to join: it becomes a free electron Majority carriers: electrons (negative), hence N -type Each donor left behind is a fixed positive ion : overall the material is neutral Si Si Si Si Si Si Si As Si Si Si Si free electron 5th electron is free (N-type)
Chapter 17 · Semiconductors
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is N-type material. An arsenic atom has taken the place of one silicon atom in the lattice. Arsenic has five valence electrons. Four of them form covalent bonds with the four neighbouring silicon atoms, exactly as silicon would. But the fifth has no bond to join. It is only loosely held, and at room temperature it breaks away and becomes a free electron, shown in yellow, wandering through the crystal. Every donor atom adds one free electron, so the conductivity rises sharply. Because the extra carriers are negative electrons, we call it N-type material, and electrons are its majority carriers. Now the trap. N-type material is not negatively charged. The arsenic atom that gave up its fifth electron is left as a fixed positive ion, locked in the lattice. For every free electron there is one fixed positive ion, so the material as a whole stays electrically neutral.
Part 2 · Doping
P-type material: holes that move An indium (or aluminium) atom has only 3 valence electrons One bond is one electron short: a hole A neighbouring electron jumps into the hole, leaving a new hole behind it So the hole moves through the crystal like a positive charge: P -type Each acceptor becomes a fixed negative ion : again neutral overall Si Si Si Si Si Si Si In Si Si Si Si hole one bond short of an electron: a hole (P-type)
Chapter 17 · Semiconductors
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now P-type material. This time an indium atom has replaced a silicon atom. Indium has only three valence electrons, so it can complete only three of its four bonds. One bond is an electron short, and that gap is called a hole, shown as a white ring. A hole behaves like a positive charge, because it is a place where an electron ought to be. Watch what happens. An electron from a neighbouring bond jumps into the hole and fills it. But in doing so, it leaves a new hole where it came from. The electron moved one way, and the hole effectively moved the other way. Hole after hole, the gap travels through the crystal like a mobile positive charge, so this is P-type material, with holes as its majority carriers. And once again it is neutral overall: the indium atom that accepted an electron becomes a fixed negative ion, one for every hole.
Part 2 · Doping
Current flow in N-type and P-type N-type : free electrons drift towards the positive terminalElectrons leaving at + are replaced by electrons entering at − P-type : electrons are drawn out at +, creating holes thereHoles drift towards the negative terminal, where electrons fill them Hole drift is in the conventional current direction, + to − N-type electrons drift towards + + − P-type holes drift towards − + − Conventional current: + to − through each bar (left to right)
Chapter 17 · Semiconductors
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
What happens when we connect a battery across doped material? In N-type material it is simple. The free electrons drift towards the positive terminal. Each electron that leaves the bar at the positive end is replaced by one entering from the negative terminal, so the balance between free electrons and fixed positive ions is kept, and a steady current flows. In P-type material the picture is a little more subtle. The positive terminal pulls electrons out of the bonds near that end, creating holes there. Those holes then drift along the bar towards the negative terminal, where electrons arriving from the battery fill them. So in P-type material we can think of the current as a drift of holes from positive to negative, which is exactly the direction of conventional current. Electrons always move from negative to positive; holes move from positive to negative.
Part 2 · Doping
Majority and minority carriers Doping decides which carrier is in the majority. Heat always adds a few of the other kind as well.
N-type P-type Impurity Donor, group V (phosphorus, arsenic, antimony) Acceptor, group III (boron, aluminium, gallium, indium) Valence electrons of impurity 5 3 Majority carriers Free electrons (−) Holes (+) Minority carriers Holes (made by heat) Electrons (made by heat) Fixed ions left in the lattice Positive Negative Overall charge Neutral Neutral
Trap: N-type is not negatively charged and P-type is not positively charged.
Chapter 17 · Semiconductors
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table brings parts one and two together. N-type material is made with a donor from group five, phosphorus, arsenic or antimony, with five valence electrons. Its majority carriers are free electrons. P-type is made with an acceptor from group three, boron, aluminium, gallium or indium, with three valence electrons, and its majority carriers are holes. There are always a few carriers of the opposite kind too, created in pairs by heat, as we saw earlier. These are the minority carriers: holes in N-type, electrons in P-type. They matter, because they cause the small leakage current through a reverse biased junction, and because their number grows quickly with temperature. Finally, the fixed ions: positive in N-type, negative in P-type. Every free carrier is matched by a fixed ion of opposite sign, so both materials are electrically neutral overall.
Part 3 · The junction
The PN junction and the depletion layer P and N material formed in one crystal , meeting at a junction Electrons diffuse from N into P, holes from P into N, and recombine This leaves a depletion layer of fixed ions with no free carriers Its charge creates a barrier potential that stops further crossing Barrier ≈ 0.6–0.7 V for silicon, 0.2–0.3 V for germanium − + − + − + − + P: holes N: free electrons depletion layer: fixed ions, no free carriers potential across the junction barrier potential silicon ≈ 0.6–0.7 V germanium ≈ 0.2–0.3 V The block as a whole is still electrically neutral
Chapter 17 · Semiconductors
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now we join P-type and N-type material together in one crystal. Near the boundary, free electrons from the N side diffuse across into the P side, and holes from the P side diffuse into the N side, where they meet and cancel out, or recombine. This leaves a thin region on each side of the junction with no free carriers at all, only the fixed ions: negative ions on the P side and positive ions on the N side. This region is called the depletion layer. Its charges set up an electric field, the barrier potential, which pushes back any further electrons or holes trying to cross, so the process stops almost at once. You can think of the barrier as a small imaginary battery across the junction: about zero point six to zero point seven volts for silicon and zero point two to zero point three volts for germanium. The block as a whole is still neutral.
Part 3 · The junction
Forward and reverse bias Forward bias : P to positive, N to negativeThe layer narrows ; once the barrier is overcome, current flows freely Reverse bias : P to negative, N to positiveThe layer widens ; only a tiny leakage current (µA) flows Leakage is due to minority carriers and rises with temperature Forward bias P N + − P to +: barrier overcome, current flows Reverse bias P N − + P to −: layer widens, only µA leakage
Chapter 17 · Semiconductors
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now connect a supply across the junction. Watch the scene. First, forward bias: the P side goes to the positive terminal and the N side to the negative. The supply pushes holes in the P region and electrons in the N region towards the junction, the depletion layer narrows, and once the applied voltage exceeds the barrier, carriers cross freely and recombine. A useful current flows, shown on the meter. Now the supply is turned round for reverse bias: P to negative, N to positive. This time the holes and electrons are pulled away from the junction, the depletion layer widens, the barrier grows and almost no current flows. All that remains is a tiny leakage current, in the order of microamps, carried by the few minority carriers. Remember that leakage rises with temperature. So a PN junction conducts one way and blocks the other.
Part 3 · The junction
The diode characteristic Forward: little current until about 0.6 V (silicon), then a steep rise In use the forward voltage stays near 0.7 V whatever the current Reverse: only leakage until the breakdown voltage At breakdown the reverse current rises sharply: a normal diode may be destroyed Ratings to know: maximum forward current and peak inverse voltage 0.2 0.4 0.6 0.8 1.0 -20 -40 -60 10 20 30 40 50 I (mA) V (volts) forward: almost no current until ≈ 0.6 V, then a steep rise → reverse: tiny leakage (µA) ← breakdown Note the different volt scales on each side of zero
Chapter 17 · Semiconductors
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph, the diode characteristic, sums up the junction's behaviour. On the right is the forward direction. As the voltage rises from zero, almost nothing happens until it approaches the barrier potential, about zero point six volts for silicon. Then the current rises very steeply, so in practice a conducting silicon diode drops about zero point seven volts whatever current it is carrying. On the left is the reverse direction, drawn on a much larger volt scale. Only a tiny leakage current flows, so small that it is exaggerated here, until the reverse voltage reaches the breakdown value. Then the junction breaks down and the reverse current rises sharply. An ordinary diode driven into breakdown will usually overheat and be destroyed, so diodes are rated for a maximum forward current and a peak inverse voltage that must not be exceeded. One special diode, the zener, is designed to work at breakdown.
Part 3 · The junction
The junction diode A PN junction used as a one-way valve: a junction diode Anode = P side; cathode = N side, marked by the bar or a bandThe symbol's arrow points in the direction of conventional forward current Behaves like the old thermionic diode valve : a rectifier Test: low resistance one way, high the other; low both ways = shorted ANODE P side (+) CATHODE N side, bar arrow = conventional current (forward) the band on the case marks the cathode Ohmmeter + on anode LOW resistance conducts Ohmmeter + on cathode HIGH resistance blocks
Chapter 17 · Semiconductors
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
A PN junction used as a one-way valve for current is called a junction diode. Its two terminals are the anode, the P side, and the cathode, the N side. In the symbol, the triangle points from the anode to the bar at the cathode, and that arrow shows the direction in which conventional current flows when the diode is forward biased. On the component itself, a band painted round the case marks the cathode end. Because it passes current one way only, the diode acts as a rectifier, doing exactly the job of the old thermionic diode valve, but with no heated filament, very little weight and a long life. You can check a diode with an ohmmeter: it should read a low resistance one way round and a high resistance the other. If it reads low both ways it has failed short circuit, and if it reads high both ways it has failed open circuit.
Part 3 · The junction
Diodes as rectifiers: AC to DC AC input Half-wave: one diode Full-wave: bridge of four diodes current reverses every half cycle only one half passes: gaps both halves turned the same way load AC AC + − Aircraft transformer rectifier units use banks of diodes (usually three-phase, full-wave) to give smooth 28 V DC.
Chapter 17 · Semiconductors
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The diode's most important job on an aircraft is rectification, turning AC into DC. On the left is the AC input; the current reverses every half cycle. With a single diode in series with the load, only the positive half cycles get through, and the negative halves are blocked. That is half-wave rectification. The output flows in one direction only, but it has big gaps, and half of the input is wasted. On the right, four diodes are arranged in a bridge. On each half cycle, two of the diodes conduct and steer the current through the load in the same direction, so both halves of the wave are used. That is full-wave rectification, with a smoother output. Transformer rectifier units on aircraft go further still, rectifying all three phases, which gives an almost smooth twenty-eight volts DC for the DC busbars.
Part 3 · The junction
Special-purpose diodes Zener diode Designed to work in reverse breakdown : the voltage across it stays constant. Used for voltage regulation and reference.
Light-emitting diode Forward biased , it gives out light as carriers recombine. Annunciators and displays; drops about 2 V.
Photodiode Reverse biased ; light frees carriers, so the leakage current rises with light. Light sensors.
Power rectifier Large-area junction on a heat sink: tens of amps in TRUs and battery chargers.
Chapter 17 · Semiconductors
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The junction can be adapted for special jobs. The zener diode is designed to work in reverse breakdown without damage. Once its breakdown voltage is reached, the voltage across it stays almost constant over a wide range of current, so zeners are used to regulate voltage and to provide reference voltages, for example in voltage regulators. Its symbol has a bent bar. The light emitting diode, or LED, is forward biased, and as electrons and holes recombine at the junction they give out light. LEDs are used in annunciators and displays and drop about two volts. The photodiode works the other way round: it is reverse biased, and light falling on the junction frees extra carriers, so its leakage current rises with the light level; it is a light sensor. Finally, power rectifier diodes simply have large junctions mounted on heat sinks, carrying tens of amps in transformer rectifier units and chargers.
Part 4 · The transistor
The junction transistor: NPN and PNP Two junctions back to back: a thin layer (≈ 25 µm) between two of the opposite type NPN : thin P between two N; PNP : thin N between two PThe three regions: emitter, base, collector (base in the middle) Symbols differ only in the emitter arrow , which shows conventional current NPN: arrow from base to emitter (out ); PNP: emitter to base (in ) NPN N E P B N C thin base (≈ 25 µm) B C E arrow points OUT (base → emitter) PNP P E N B P C thin base (≈ 25 µm) B C E arrow points IN (emitter → base) The arrow is on the emitter and shows conventional current
Chapter 17 · Semiconductors
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The bipolar or junction transistor is in effect two junction diodes back to back. It is a sandwich: a very thin layer of one type, typically about twenty-five micrometres, between two layers of the other type. A thin P layer between two N layers gives an NPN transistor; a thin N layer between two P layers gives a PNP transistor. The three regions are called the emitter, the base and the collector, and the base is always the thin one in the middle. The emitter is heavily doped, because it supplies the carriers. In the circuit symbols the only difference is the arrow, which is drawn on the emitter and always shows the direction of conventional current. In an NPN transistor it points out, from base to emitter. In a PNP transistor it points in, from emitter to base. A handy memory aid for NPN: not pointing in.
Part 4 · The transistor
How an NPN transistor conducts Collector-emitter voltage alone: no current (one junction is reverse biased) Forward bias the base-emitter junction: electrons pour into the base The base is so thin that few recombine; most are swept on into the collector A small base current controls a large collector current PNP works the same way with all supplies reversed + + small I B large I C Base switch closed → base current → collector current → lamp lit
Chapter 17 · Semiconductors
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how an NPN transistor works. The main supply is connected between collector and emitter, through a lamp. On its own, nothing happens, because the collector-base junction is reverse biased, so the lamp stays dark. Now close the base switch, which forward biases the base-emitter junction with a small bias supply. Electrons pour from the heavily doped emitter into the base. But the base is very thin and lightly doped, so there are few holes for them to combine with, and most of the electrons diffuse straight through into the collector, where the positive collector voltage sweeps them up. Watch the wires: a small base current, in the thin wire, lets a large collector current flow in the thick wire, and the lamp lights. In electron terms the big flow is from emitter to collector; in conventional terms, collector to emitter. A PNP transistor works the same way with every supply reversed.
Part 4 · The transistor
Current gain: a worked example Current gain β = IC ÷ IB ; typically 50 to 300Example: IB = 50 µA, β = 100 → IC = 5 mA All the current leaves by the emitter: IE = IB + IC = 5.05 mA The emitter current is the largest ; the base current the smallest Remove the base current and the collector current stops I B I C I E Worked example Base current I B = 50 µA Current gain β = 100 I C = β × I B = 100 × 50 µA = 5 mA I E = I B + I C = 5.05 mA Switch I B off: I C falls to zero
Chapter 17 · Semiconductors
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ratio of collector current to base current is called the current gain, and it is usually given the Greek letter beta. Typical values are fifty to three hundred. Let us work an example. Suppose the base current is fifty microamps and the gain is one hundred. The collector current is one hundred times fifty microamps, which is five thousand microamps, or five milliamps. Where does all this current go? Both the base current and the collector current leave through the emitter, so the emitter current is their sum: five milliamps plus zero point zero five milliamps, which is five point zero five milliamps. So the emitter carries the largest current, the collector nearly as much, and the base the least by far. And remember the key point: remove the small base current, and the large collector current stops. That is what makes the transistor a controlled valve.
Part 4 · The transistor
The transistor as a switch and as an amplifier As a SWITCH As an AMPLIFIER base current (small, µA) collector current (large, mA) base on → fully on; base off → fully off base: bias + small AC signal bias collector: the same shape, much larger gain ≈ β: a small signal controls a large one Switch: logic gates, static inverters, relay drivers. Amplifier: radio receivers, sensor signals, audio.
Chapter 17 · Semiconductors
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because a small base current controls a large collector current, the transistor can be used in two ways. As a switch, the base current is simply turned fully on or fully off. With base current, the transistor is turned hard on and the collector current flows at full strength; without it, the transistor is off and no collector current flows at all. There are no moving contacts, no arcing, and it can switch millions of times a second. That is how logic gates, static inverters and relay drivers work. As an amplifier, a steady bias current is applied to the base so that the transistor is partly on, and a small alternating signal is superimposed on that bias. The collector current then follows the same wave shape, but much larger. That is how the weak signals from an aerial or a sensor are built up to a useful size.
Part 4 · The transistor
Integrated circuits Doping can be applied to precisely chosen areas of one silicon slice Made by photo-etching : mask, expose, etch, dope, repeat Transistors, diodes, resistors and capacitors all on one chip Many chips are made at once on a wafer Result: small, light, reliable and cheap electronics, like the computer chip silicon wafer: hundreds of chips one chip: millions of transistors, diodes, resistors 1 coat with light-sensitive resist 2 expose through a mask (photo-etching) 3 etch away the exposed areas 4 dope the opened regions repeat layer by layer
Chapter 17 · Semiconductors
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
The final step is the integrated circuit. Because doping can be applied to precisely chosen areas of a slice of silicon, we do not need to make transistors one at a time. Using photo-etching, the silicon is coated with a light-sensitive layer, exposed to light through a mask that carries the circuit pattern, and the exposed areas are etched away so that the regions underneath can be doped. Repeating this layer by layer builds up transistors, diodes, resistors and even small capacitors, all joined by metal tracks, in one small piece of silicon called a chip. Hundreds of identical chips are made at once on a round wafer. The ubiquitous computer chip is the best example, with millions of transistors. The results are electronics that are small, light, cheap and very reliable, and as production techniques improve, ever more powerful circuits keep finding their way into modern airliners.
Exam traps
Common traps with semiconductors Neutral materials N-type and P-type are both electrically neutral: every free carrier is matched by a fixed ion.
Donor or acceptor 5 valence electrons (arsenic, antimony, phosphorus) = donor, N-type. 3 (indium, aluminium, boron) = acceptor, P-type.
Temperature Semiconductor resistance falls as temperature rises (NTC); metals go the other way.
Bias Forward: P to +, layer narrows, current flows. Reverse: P to −, layer widens, only µA leakage.
Arrow direction Diode and transistor arrows show conventional current. NPN emitter arrow points out; PNP points in.
Currents I E = I B + I C. Emitter current is largest. Electron flow emitter → collector in an NPN.
Chapter 17 · Semiconductors
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the traps. First, N-type and P-type material are both electrically neutral; do not be tempted to call N-type negative. Second, donors have five valence electrons and make N-type, acceptors have three and make P-type. If you forget, think N for negative carriers, which means extra electrons, which means five. Third, a semiconductor's resistance falls as it warms up, the opposite of a metal. Fourth, forward bias means P to positive; the layer narrows and current flows. Reverse bias means P to negative; the layer widens and only a few microamps of leakage flow. Fifth, the arrows on diode and transistor symbols always show conventional current; the NPN arrow points out, the PNP arrow points in. Sixth, the emitter current is the sum of the base and collector currents, and in an NPN transistor the electrons themselves travel from emitter to collector.
Summary
What to take into the exam Materials Conductors: many free electrons. Insulators: few. Semiconductors (Si, Ge, 4 valence) in between.
Temperature Heat frees electron-hole pairs: semiconductor resistance falls (NTC).
N-type Donor, 5 valence (As, Sb, P). Majority: electrons. Neutral overall.
P-type Acceptor, 3 valence (In, Al, B). Majority: holes. Neutral overall.
Junction Depletion layer and barrier: 0.6–0.7 V Si, 0.2–0.3 V Ge. Forward conducts, reverse blocks.
Diodes Arrow = conventional current, bar = cathode. Rectifiers, zener, LED, photodiode.
Transistor Emitter, thin base, collector. NPN arrow out, PNP in. Small I B controls large I C.
Uses Switch or amplifier; integrated circuits by photo-etching on one chip.
Chapter 17 · Semiconductors
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us sum up. Conductors have many free electrons, insulators very few, and semiconductors such as silicon and germanium, with four valence electrons, sit in between. Heat frees electron-hole pairs, so a semiconductor's resistance falls as it warms. Doping with a donor of five valence electrons, such as arsenic, antimony or phosphorus, makes N-type material with electrons as majority carriers; doping with an acceptor of three, such as indium, aluminium or boron, makes P-type with holes as majority carriers. Both stay neutral. Where P meets N, a depletion layer forms with a barrier of about zero point seven volts in silicon; forward bias conducts, reverse bias blocks. The diode's arrow shows conventional current and its bar marks the cathode. A transistor has an emitter, a thin base and a collector, and a small base current controls a large collector current, so it works as a switch or an amplifier, and millions fit on one chip.