Engines · Chapter 15
Air Inlets The intake's job is to hand the compressor a smooth, slow, high-pressure stream of air at every speed and attitude. Here is how subsonic and supersonic intakes do it, and how pilots keep them working.
the intake
fan face
lip
smooth · uniform · slowed down · pressure raised
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to air inlets. The intake looks like the simplest part of a jet engine, just a hole at the front, yet the whole engine depends on it. Its job is to deliver air to the fan or compressor smoothly, evenly and at the right speed, whether the aircraft is standing still at full power, cruising at Mach point eight, or flying at twice the speed of sound. In this lesson you will see why subsonic intakes widen towards the engine, why the pressure inside is below ambient at the start of the take-off roll, how supersonic intakes tame shock waves, and what pilots do about crosswinds, ice, damage, debris and turbulence.
Roadmap
The front door of the engine
Subsonic pitot intake
S-duct to a tail engine
Supersonic: shocks
1 · Purpose Smooth, even air for the fan. Pitot and S-duct installations.
2 · Subsonic intakes The divergent duct, depression on the ground, ram recovery and ram compression, auxiliary doors.
3 · Supersonic intakes Shock losses, supersonic and subsonic diffusers, ramps, spikes and spill doors.
4 · Operations Crosswind and rolling take-off, blade stall, icing, EPR probes, damage, FOD, turbulence.
Chapter 15 · Air Inlets
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First, the purpose of the intake and the common installations: pods under the wing with short straight intakes, and tail engines fed by S-shaped ducts. Second, the subsonic intake: why it is a divergent duct, why the pressure inside it is below ambient when the aircraft is standing still, what ram pressure recovery means, how the intake adds free compression at speed, and what secondary inlet doors are for. Third, supersonic intakes, which must slow the air below the speed of sound before it reaches the compressor, using shock waves, ramps, spikes and spill doors. Finally, the practical side: crosswind and the rolling take-off, why a disturbed or slowed airflow stalls compressor blades, intake icing and iced pressure probes, intake damage, foreign object damage, ground running and turbulence. Exam questions come from every part.
Part 1 · Purpose
What the intake must do Built into the airframe or the front of the nacelle Deliver a relatively turbulence-free supply of air to the face of the LP compressor or fan At every airspeed and angle of attack , from standing still to cruise Slow the air down and raise its pressure with the smallest possible loss A poor intake causes compressor stall and surge , and wastes thrust
Good: uniform, turbulence-free flow
fan face
Bad: distorted flow at the fan face
separated,
turbulent air
fan face
Distortion → compressor stall or surge
Chapter 15 · Air Inlets
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The engine air inlet is built into the airframe or into the front of the engine nacelle, and it has one job: to deliver a relatively turbulence-free supply of air to the face of the low pressure compressor or fan. Notice the words relatively turbulence-free and face; that is the exact exam definition. The intake has to do this at every airspeed and every angle of attack, from standing still at full power to high speed cruise. It also has to slow the air down and raise its pressure with as little loss as possible, because every bit of pressure lost in the intake is lost from the whole engine. Look at the two drawings. In the good intake the air arrives evenly over the whole fan face. In the bad one, the flow has separated from one side and the fan sees a patch of slow, turbulent air. That kind of distortion is a classic cause of compressor stall and surge.
Part 1 · Purpose
Where intakes are fitted
Wing pod: straight pitot
Tail engine: S-duct
Fuselage side intakes
short, straight duct: little loss
but low over the ground: FOD risk
curved duct (727, TriStar)
unstable flow in crosswinds
short ducts to engines in the body
high-speed designs may be variable
The pitot intake (single circular entry) is the simplest. Straight on wing pods; shaped into an S-duct for tail-mounted engines.
Chapter 15 · Air Inlets
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the common installations. On most airliners the engines hang in pods under the wing, and each has the simplest kind of intake: a single, circular, pitot type entry, with a short, straight duct to the fan. That gives very little loss, but it puts the intake low over the ground, where it can pick up debris. Some aircraft carry an engine in the tail. On the Boeing seven two seven and the Lockheed TriStar the centre engine sits in the tail cone, fed by an intake above the fuselage through an S-shaped duct. The bends make the airflow less stable, and unstable flow in an S duct is a common problem, particularly in crosswind take-offs. Military aircraft often have intakes in the sides of the fuselage with short ducts to engines buried in the body, and high speed designs may make those intakes variable, as we will see in part three.
Part 2 · Subsonic intakes
The pitot intake Single entrance, circular cross-section : the simplest intake Makes the most of ram effect Suffers the least loss of ram pressure as altitude increases Rounded lips help at low speed and at angles of attack Efficiency falls as the aircraft nears Mach 1 : a shock wave forms at the lip
The pitot intake
rounded lip
single circular entry
fan face
Subsonic:
makes the most of ram effect
Altitude:
least loss of ram pressure
Near Mach 1:
shock at the lip (red), efficiency falls
Chapter 15 · Air Inlets
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The pitot intake is the simplest form of intake: a single entrance with a circular cross section, rather like the pitot tube that measures airspeed, which is where its name comes from. It is excellent at subsonic speed. It makes the most of the ram effect, the pressure rise that comes from the forward motion of the aircraft, and it suffers the least loss of ram pressure as altitude increases. Its lips are well rounded, so that air coming in from slightly off-axis, at low speed or at an angle of attack, can still turn smoothly into the duct. Its limit is speed. As the aircraft approaches the speed of sound, a shock wave forms at the intake lip, and the shock causes a loss of pressure, so the intake becomes less efficient. That is why airliners cruise below Mach one with pitot intakes, and why supersonic aircraft need a different design.
Part 2 · Subsonic intakes
Why the subsonic intake widens A subsonic intake is usually a divergent duct : wider at the fan than at the lip Same mass flow through a bigger area: velocity falls Kinetic energy becomes pressure: static pressure rises at the compressor face The fan blades work best with air at about Mach 0.5–0.6 , not at flight speed Example: area × 1.33 → 200 m/s becomes 150 m/s, about 3.6 kPa gained
Divergent duct: slow down, pressure up
200 m/s
150 m/s
lip / throat: area A
fan face: 1.33 A
Same mass flow: velocity × area = constant
Area × 1.33 → velocity ÷ 1.33: 200 → 150 m/s
Bernoulli: Δp = ½ ρ (V₁² − V₂²)
= ½ × 0.41 × (200² − 150²) ≈ 3.6 kPa
ρ = 0.41 kg/m³, about 35 000 ft (low-speed approximation)
Chapter 15 · Air Inlets
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A subsonic intake is normally a divergent duct: it gets wider from the lip back to the compressor face. Why? The same mass of air passes every section each second, so where the area is larger the air must move more slowly. As it slows, its kinetic energy is turned into pressure, so the static pressure rises towards the compressor face. That suits the engine, because the fan blades work best when the air reaches them at around Mach nought point five or six, not at the aircraft's cruising speed. Here is a worked example. If the area grows by a third, the velocity falls by the same factor, from two hundred to one hundred and fifty metres per second. At cruise altitude, where the density is about nought point four one kilograms per cubic metre, Bernoulli's equation gives a static pressure rise of about three point six kilopascals, free pressure delivered to the compressor before it has done any work at all.
Part 2 · Subsonic intakes
Standing still: pressure below ambient Engine running, aircraft stationary : air is sucked in from all round the intake It accelerates into the intake, so the pressure there is below ambient : P1 < P0 The faster the airflow (higher power), the deeper the depression At cruise the captured stream tube is smaller than the lip: the air slows ahead of the intake Pressure in the intake then exceeds ambient: ram compression
Standing still, high power
P1 below P0 (depression)
Cruise
P1 above P0 (ram compression)
spillage
Chapter 15 · Air Inlets
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
When a gas turbine runs on a stationary aircraft, the pressure inside its intake is below ambient. The air outside is at rest, and the engine has to suck it in. To flow into the intake the air must accelerate, and accelerated air has a lower static pressure. Look at the top drawing: air is drawn in from all around, even from beside the lip. The higher the power, the faster the airflow and the deeper the depression. So in exam terms, a high bypass engine with a pitot intake, running with the brakes on, has a P one less than P nought. Now look at the cruise picture. The aircraft is moving faster than the air needs to enter, so the stream tube the engine captures is actually smaller than the lip, and the air slows down and gains pressure before it even reaches the intake. Extra air spills round the outside. Inside, the pressure is now above ambient.
Part 2 · Subsonic intakes
Ram pressure recovery As the aircraft starts to move, the pressure in the inlet starts to rise The point where inlet pressure is back to ambient is ram pressure recovery Usually reached at about Mach 0.1 to 0.2 Faster still, the intake gives more and more ram compression Not an EPR or RPM setting: it is about intake pressure versus ambient
Intake pressure ÷ ambient pressure (P1 ÷ P0)
0
0.2
0.4
0.6
0.8
0.9
1.0
1.2
1.4
1.6
Flight Mach number
ambient
at rest: 0.98
ram recovery ≈ M 0.17
1.49 at M 0.8
depression
Above recovery the intake adds ram compression
model: P1/P0 = 0.98 × (1 + 0.2 M²)3.5
Chapter 15 · Air Inlets
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Follow the intake pressure through the take-off. At rest, in this model with a two per cent duct loss, it is about ninety eight per cent of ambient: the depression we just saw. As the aircraft begins to roll, the forward speed starts to ram air into the intake and the pressure rises. At some speed it gets back to ambient pressure, and that point is called ram pressure recovery. It is usually reached at about Mach nought point one to nought point two; here the curve crosses at about Mach nought point one seven. Be careful with the definition in the exam. Ram pressure recovery is not about the E P R reaching its take-off value or the compressor reaching any maximum. It is simply the moment the intake pressure is re-established to ambient pressure. Above that speed the intake produces more and more ram compression, about one and a half times ambient at Mach nought point eight.
Part 2 · Subsonic intakes
Ram compression is free Above recovery the intake raises the pressure before the compressor The overall pressure ratio of the engine increases So the engine makes more thrust for no extra fuel flow M 0.8: ram ratio ≈ 1.49; with a 30 : 1 compressor, ≈ 45 × ambient at the combustor Pitot intakes keep this ram rise well at altitude
Ram compression comes free
M 0.00
× 0.98
take-off roll
M 0.30
× 1.04
climb-out
M 0.50
× 1.16
M 0.80
× 1.49
cruise
M 0.85
× 1.57
fast cruise
Worked example: compressor pressure ratio 30 : 1
Standing still: 0.98 × 30 ≈ 29 × ambient at the combustor
At M 0.8: 1.49 × 30 ≈ 45 × ambient
Higher overall pressure ratio, more thrust for the same fuel
Chapter 15 · Air Inlets
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once ram recovery has been passed, the intake becomes a compressor in its own right, and a free one. The bars show the ratio of intake pressure to ambient at different Mach numbers: just below one on the take-off roll, about one point one six at Mach nought point five, and about one point four nine at Mach nought point eight. The engine's compressor then multiplies whatever pressure it is given. Take a compressor with a pressure ratio of thirty to one. Standing still, it delivers about twenty nine times ambient pressure to the combustor. At Mach nought point eight it delivers about forty five times ambient, because the intake has already done part of the work. A higher overall pressure ratio means more thrust without any increase in fuel flow, and better efficiency. That is one reason the gas turbine is so well suited to high speed flight.
Part 2 · Subsonic intakes
Secondary air inlet doors Spring-loaded doors in the intake cowl (also called blow-in or auxiliary doors) Used at high power when stationary , at low airspeed or high angle of attack The intake depression sucks them open : supplementary air reaches the compressor face As speed builds, ram pressure closes them Closed in the cruise and at high IAS
Stationary, high power
doors sucked open: extra air
spring-loaded door
At speed
ram pressure: doors closed
spring-loaded door
Chapter 15 · Air Inlets
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some intakes are sized for efficient cruise, which makes them a little too small for the huge airflow needed at full power on the ground. The answer is secondary air inlet doors, sometimes called blow-in or auxiliary doors. They are spring-loaded doors in the sides of the intake cowl. When the engine is at high power and the aircraft is stationary, or at low airspeed, or at a high angle of attack, the depression inside the intake is deep. The pressure difference across the doors overcomes their springs, they open inwards, and a supplementary airflow reaches the compressor face. As the aircraft gains speed, ram pressure builds up inside the intake, the depression disappears, and the springs and the pressure close the doors. They stay closed in the cruise and at high indicated airspeed. So the exam answer is clear: secondary inlet doors are used when the R P M is high and the aircraft is stationary.
Part 3 · Supersonic intakes
Why supersonic air needs special handling The compressor face cannot cope with supersonic airflow The intake must slow the air to below Mach 1 and control the shock waves A single normal shock does it in one step, but wastes pressure Loss grows fast: 7 % at M 1.5, 28 % at M 2, 67 % at M 3 Better: several oblique shocks first, then one weak normal shock
Pressure kept across one normal shock
1
1.5
2
2.5
3
0 %
25 %
50 %
75 %
100 %
Mach number in front of the shock
M 1.2: 99 %
M 1.5: 93 %
M 2: 72 %
M 3: 33 %
A plain pitot intake is fine to about M 1.5;
faster, use oblique shocks first, then a weak normal shock
Chapter 15 · Air Inlets
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
A supersonic aircraft needs a special kind of intake, because the compressor face cannot cope with supersonic airflow. Below the speed of sound the intake must still recover pressure like a subsonic one, but above it, the intake must slow the air to below Mach one and control the shock waves that form. The crudest way is a plain pitot intake with a single normal shock standing across its mouth. The air passes through the shock and becomes subsonic in one step, but a strong shock destroys total pressure. The graph, computed from the shock equations, shows how much survives. At Mach one point five you keep about ninety three per cent, which is acceptable. At Mach two you keep only seventy two per cent, and at Mach three barely a third. So faster aircraft slow the air in several gentle steps, with oblique shock waves, and finish with one weak normal shock.
Part 3 · Supersonic intakes
Supersonic diffuser, then subsonic diffuser
movable ramp (dashed)
weak normal shock
M 2.0
M 1.3
M ≈ 1
M 0.8
M 0.5
Supersonic diffuser: area decreases
slows the air to just below Mach 1
Subsonic diffuser: area increases
slows it further, pressure rises
throat
compressor
face
spill door
In supersonic flow a converging duct slows the air; in subsonic flow a diverging one does. Variable geometry keeps the shocks in place; spill doors dump excess air.
Chapter 15 · Air Inlets
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the layout of a variable throat supersonic intake. It looks the wrong way round at first. The front part, the supersonic diffuser, gets narrower. That is because supersonic flow behaves the opposite way to subsonic flow: in a converging duct it slows down. So the supersonic diffuser reduces the air velocity from, say, Mach two to just below Mach one at the throat, where a weak normal shock completes the change. Behind the throat the duct widens. This is the subsonic diffuser, and it works exactly like a normal subsonic intake, slowing the air further and raising its pressure until it reaches the compressor face at around Mach nought point five. The throat area must suit the Mach number, so a movable ramp changes it. And when the intake captures more air than the engine needs, spill doors let the excess escape without forcing it through the shocks.
Part 3 · Supersonic intakes
External and internal compression A ramp or spike ahead of the lip makes oblique shocks : external compression Each oblique shock slows the air a little with small losses A weak normal shock at or just inside the lip makes the flow subsonic: internal compression For best results the shocks must meet the cowl lip Their angle changes with Mach number, so the geometry must move
External / internal compression
oblique shocks
small, efficient steps
weak normal shock
then subsonic
ramp (external compression)
cowl lip
• Several weak shocks lose far less pressure than one strong one
• Shocks must sit exactly on the lip: their angle changes with Mach
• So the geometry (ramp or spike) must move with speed
Chapter 15 · Air Inlets
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The best supersonic intakes compress the air partly outside and partly inside the duct. A wedge-shaped ramp, or a cone-shaped spike, sits ahead of the cowl lip. The supersonic air meets it and forms an oblique shock wave. Air passing through an oblique shock slows a little and gains pressure, with only a small loss. A second change of ramp angle makes a second oblique shock, and so on. Several weak shocks waste far less energy than one strong one. That is the external compression. Finally, at or just inside the lip, a weak normal shock makes the flow subsonic, and the subsonic diffuser does the rest; that is the internal compression. For the intake to work at its best the oblique shocks must just touch the cowl lip. But the angle of a shock depends on the Mach number, so as the speed changes the ramp or spike has to move to keep the shocks in place.
Part 3 · Supersonic intakes
Movable ramps and spikes Moveable ramps change the cross-sectional area of the intake (Concorde )Moveable centre-body spikes slide fore and aft (SR-71 )Both control the shock waves and so the airflow to the compressor face Spill doors let excess air escape without changing its velocityAll automatic, scheduled with Mach number
Movable ramps (Concorde)
Moving spike (SR-71)
ramps lowered at high Mach:
smaller throat area
spill door
conical shock
kept on the lip
spike forward: low Mach
spike aft: high Mach
Chapter 15 · Air Inlets
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two famous examples show how variable intakes work. Concorde had rectangular intakes with hinged ramps in their roofs. As the Mach number rose, the ramps were lowered, changing the cross-sectional area of the intake and the throat to keep the shock system in the right place. A spill door in the floor of the intake let excess air out. The SR seventy one Blackbird had round intakes with a cone-shaped spike in the centre. At low supersonic speeds the spike sat forward. As speed increased it moved aft, by more than two feet, keeping its conical shock wave on the cowl lip and the normal shock inside the throat. In both cases the movement was automatic, scheduled with Mach number. Remember the exam pairing: movable ramps change the cross-sectional area of the intake, as on Concorde, and movable spikes control the shock position, as on the SR seventy one.
Part 4 · Operations
Take-off: crosswind and the rolling start The intake cannot cope with high angles of attack or strong crosswinds and keep the flow stable One of the most critical times: accelerating to take-off power Crosswind: air separates inside the upwind lip ; worst with S-duct tail engines (727, TriStar) Turbulent flow at the fan face can cause stall or surge Rolling take-off : get moving, then set take-off power smoothly by about 60–80 kt
Crosswind, low speed, high power
crosswind
separation inside the upwind lip
distorted flow → stall / surge
Rolling take-off
0 kt
40 kt
80 kt
120 kt
T/O power set by 60–80 kt
moving first
Chapter 15 · Air Inlets
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The intake is designed to keep the airflow to the compressor stable, and anything that makes that flow turbulent can stall or surge the compressor. The intake cannot cope with very high angles of attack, and one of the most critical moments is the acceleration to take-off power. With the aircraft standing still, the engine is sucking air in from all around, and a crosswind makes the air turn sharply round the upwind lip. It separates from the inside of the duct and the fan face sees distorted flow. Aft-mounted engines with S-ducts, like those on the TriStar and the seven two seven, are the most sensitive. The procedure in the operating manual must be followed, and it is typically a rolling take-off: get the aircraft moving forwards first, then increase power smoothly so that take-off power is set by about sixty to eighty knots, when ram air is helping the intake.
Part 4 · Operations
Why slow or distorted air stalls the blades Each compressor blade meets the air like a small propeller blade Its angle of attack is set by blade speed (RPM) and the axial velocity of the air Ice, distortion or a high-power static run in an S-duct reduce axial velocity At the same RPM the relative airflow swings round: angle of attack increases Example: axial 200 → 120 m/s at 300 m/s blade speed: α ≈ 6° → 18° : stall, then surge
Normal axial velocity
axial 200
blade 300
α ≈ 6°
helix of the air 34° · blade 40°
flow attached
Axial velocity reduced
axial 120
blade 300
α ≈ 18°
helix of the air 22° · blade 40°
blade stalls → surge
Chapter 15 · Air Inlets
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
To see why intake problems stall compressors, look at a single compressor blade. It meets the air just like a propeller blade section. Its angle of attack depends on two velocities: the blade speed, set by the R P M, and the axial velocity of the air flowing through the engine. In the scene the forward speed arrow plays the part of the axial velocity. Now reduce it, as ice in the intake, a distorted airflow, or a static high power run with an S duct would do. The R P M is unchanged, so the relative airflow swings round towards the plane of rotation and the angle of attack increases. Reduce it further and the blade passes its stalling angle. In the worked example, cutting the axial velocity from two hundred to one hundred and twenty metres per second raises the angle of attack from about six degrees to about eighteen. The blades stall first, and stalled stages can then lead to a surge of the whole compressor.
Part 4 · Operations
Intake icing Likely when the temperature is +10 °C or below with visible moisture Also standing water, slush or snow on the runway, or RVR below 1 000 m Then the pilot selects engine anti-icing ON (hot bleed air to the lip) Ice reduces the intake area and distorts the airflow : lower axial velocity, higher blade α, stall Ice shed from the lip can damage the fan
ice on the lip
less area, distorted flow, ice shed into the fan
Engine anti-ice ON when OAT ≤ +10 °C and:
visible moisture (cloud, fog, rain, snow)
standing water, slush or snow on the runway
visibility (RVR) below 1 000 m
Hot bleed air heats the lip (turboprops often electric)
Typical values; always follow the aircraft manual
Chapter 15 · Air Inlets
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Intake icing can occur whenever the conditions are right. The usual rule is that icing is possible when the ambient temperature is plus ten degrees or below and there is visible moisture, such as cloud, fog, rain or snow, or when there is standing water, slush or snow on the runway, or when the runway visual range is less than one thousand metres. Notice the plus ten: the air accelerating into the intake cools, so ice can form even above freezing. In these conditions the pilot should switch on engine anti-icing, which on a jet sends hot bleed air from the compressor to heat the intake lip. Ice on the lip reduces the intake area and disturbs the airflow. The axial velocity falls, the angle of attack on the compressor blades rises, and the compressor may stall. Large pieces of ice breaking away can also be swallowed and damage the fan blades.
Part 4 · Operations
An iced P1 probe and the EPR gauge Engine pressure ratio : exhaust pressure ÷ inlet pressure (P7 ÷ P1 here)Used as the thrust gauge on many engines If ice blocks the P1 probe , it no longer senses true inlet pressure and reads low As RPM increases and P7 rises, the indicated EPR increases too much The gauge over-reads : the crew set less thrust than they think
EPR = P7 ÷ P1
P1
P7
True
25.0 ÷ 14.70 = 1.70
P1 probe iced
25.0 ÷ 12.25 = 2.04
A blocked P1 probe reads too low, so as RPM rises
the indicated EPR rises too much: it over-reads,
and the real thrust is less than the gauge shows
illustrative pressures in psi
Chapter 15 · Air Inlets
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many jet engines use engine pressure ratio as their thrust gauge: the pressure at the exhaust divided by the pressure at the inlet, P seven over P one in our numbering. That makes the inlet probe, P one, very important, and it sits right in the icing zone. If ice blocks the P one probe, it no longer senses the true inlet pressure, and the pressure trapped in it ends up lower than it should be. Now advance the thrust levers. The R P M increases and the exhaust pressure rises normally, but it is being divided by a P one that is too small, so the indicated E P R increases more than it should. In the example, the true ratio is one point seven, but the iced probe makes the gauge show two point nought four. The crew set the target E P R and believe they have full thrust, when in fact they have much less. Exactly this has caused fatal accidents.
Part 4 · Operations
Damage and foreign objects Intake damage or roughness makes the airflow turbulent: possible stall or surge Most compressor damage is foreign object damage (FOD) , on or near the ground Wing pods with intakes close to the ground suffer most; tail engines much less Clear the ramp; check intakes on the walk-round; minimum power for start, taxi and reverse After flight: intake and exhaust covers . Ground runs: debris guards
Wing pod: intake low over the ground
ground vortex lifts stones and debris
Most compressor damage is FOD , picked up on or near the ground
Walk-round: intakes and the ground in front clear of debris
Look for intake damage, uneven panels, roughness
Keep power low for start, taxi and reverse thrust
After flight: fit intake and exhaust covers (dirt, windmilling)
Ground runs: fit debris guards where provided
Chapter 15 · Air Inlets
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Anything that roughens the inside of the intake can make the incoming air turbulent and upset the flow to the compressor, causing a stall or surge. So during the intake inspection, look carefully for damage, dents, uneven skin panels and surface roughness. The bigger threat is foreign object damage. Damage to compressor blades is almost always caused by objects swallowed while the aircraft is on or close to the ground, and once a blade is damaged its shape changes, performance deteriorates and the compressor may stall or surge. Wing mounted engines, with their intakes close to the ground, are the most exposed; a vortex can even form between the ground and the intake and lift stones into it. Engines mounted high on the rear fuselage suffer much less. The precautions: keep the ramp clear, check the ground in front of the intakes before start, use minimum power for start, taxi and reverse thrust, fit intake and exhaust covers after flight, and use debris guards for ground runs.
Part 4 · Operations
People, ground runs and turbulence People have been killed and injured by being sucked into running engines Keep well clear of the intake danger zone and the jet blast Covers after flight also stop the engine windmilling in the wind Severe turbulence can disrupt intake airflow : compressor malfunction or flame-out Fly the turbulence penetration speed , set the recommended RPM/EPR , use continuous ignition
engine
intake danger zone
people can be sucked in
jet blast: hot, fast
Severe turbulence in flight
fly the turbulence penetration speed
set the recommended RPM / EPR
continuous ignition ON: guards against flame-out
disturbed intake flow can stall the compressor
Chapter 15 · Air Inlets
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
A running gas turbine is dangerous to people on the ground. Several people have been killed, and many seriously injured, by being sucked into the intakes of running engines, so great care is needed whenever anyone has to work close to one. Every type has a marked intake danger zone in front of the engine, and a much longer zone behind it where the jet blast is hot and fast enough to throw people and vehicles about. When the aircraft is parked, intake and exhaust covers keep out dirt and birds and stop the wind turning the engine over, which is called windmilling. In the air, the main intake hazard is heavy turbulence, which can seriously disrupt the airflow into the engines. The operating handbook gives the answer: fly at the turbulence penetration speed and set the recommended R P M or E P R, and it may be prudent, or required, to switch on continuous ignition to reduce the chance of a flame-out.
Summary
Air inlets in eight lines Purpose Relatively turbulence-free air to the face of the LP compressor or fan, at all speeds and attitudes.
Pitot intake Best ram use, least ram loss with altitude; loses efficiency near Mach 1 (lip shock).
Subsonic: divergent Divergent before the fan: slows the air to subsonic and raises its pressure.
Static, recovery Stationary: P1 < P0. Ram recovery (back to ambient) at about M 0.1–0.2. Aux doors open at high RPM when static.
Supersonic Converging supersonic diffuser to below M 1, then diverging subsonic diffuser. Ramps, spikes, spill doors.
Take-off Crosswind and S-ducts distort flow. Rolling take-off: power set by 60–80 kt.
Ice ≤ +10 °C with visible moisture, standing water or RVR < 1 000 m: anti-ice ON. Iced P1 → EPR over-reads.
Damage & FOD Low axial velocity → higher blade α → stall, surge. Clear ramp, covers, low power, debris guards.
Chapter 15 · Air Inlets
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us sum up. The intake delivers relatively turbulence-free air to the face of the low pressure compressor or fan at every speed and attitude. The pitot intake makes the best use of ram effect and loses least ram pressure with altitude, but loses efficiency near Mach one when a shock forms at the lip. A subsonic intake is divergent before the fan, so the air slows to a suitable subsonic speed and its pressure rises. On the ground the intake pressure is below ambient; it returns to ambient, ram recovery, at about Mach nought point one to nought point two, and secondary doors help at high R P M when stationary. Supersonic intakes slow the air in a converging diffuser, then a diverging one, using ramps, spikes and spill doors. Crosswinds and S-ducts call for a rolling take-off. Ice needs anti-ice, and an iced P one probe makes the E P R over-read. And slowed or distorted air raises the blade angle of attack, leading to stall and surge.