Engines · Chapter 29
Engine Bleed Air Air taken from the compressor: the aircraft services it supplies, how LP and HP bleed is controlled, what it costs in thrust and fuel, and how internal air cools the turbine and seals the bearings.
precooler
fan air
to the aircraft
HP bleed
internal air: cooling and sealing
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter twenty-nine is about bleed air, the air taken from the engine compressor before it reaches the combustor. Outside the engine it runs the air conditioning and pressurisation, the anti-icing and many other services. Inside the engine it cools the turbine and seals the bearing chambers. We will see where it is taken from and why, how the valves are scheduled, what bleeding costs in thrust, temperature and fuel, and how turbine blades survive in gas hotter than their own melting point.
Roadmap
Air that never reaches the combustor Air bled from the compressor is used outside the engine for aircraft services and inside it for cooling and sealing.
1 · External users Air conditioning, anti-icing and other services ; the pneumatic system.
2 · Control LP and HP bleed ports, valves, precooler , isolation and fire.
3 · The cost Effect on thrust, EPR, EGT, RPM and SFC ; low pressure, high volume air.
4 · Internal air Turbine blade, NGV and disc cooling , clearance control, seals , disposal and IEOH .
Chapter 29 · Engine Bleed Air
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson is about bleed air: air taken from the engine compressor that never reaches the combustor. It has two families of uses. Outside the engine, it supplies aircraft services. Inside the engine, it cools the hot parts and seals the bearing chambers. In part one we list the external users. In part two we see how bleed is controlled: low and high pressure bleed ports, the valves, the precooler, and how bleed is isolated in a fire. Part three is the cost: what bleeding does to thrust, E P R, exhaust gas temperature, RPM and specific fuel consumption. Part four is the internal air system: cooling the turbine blades, nozzle guide vanes and discs, active clearance control, the different kinds of seal, how the used air is disposed of, and the internal engine overheat warning.
Part 1 · External users
What bleed air is Bleed air is air taken from the compressor before the combustorInternal use: cooling and sealing the engineExternal use: services for the aircraftThe air is compressed , so it is under pressure and hot Every kilogram bled has cost compressor work but gives no thrust Two families of bleed air compressor combustor turbine EXTERNAL: aircraft services INTERNAL: cooling and sealing Every kilogram bled has had work done on it but gives no thrust from the turbine and nozzle
Chapter 29 · Engine Bleed Air
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bleed air is air taken from the engine compressor before it reaches the combustor. Because it has already been compressed, it is under pressure and it is hot, which makes it very useful. It has two families of uses. Internally, it is ducted through the engine to cool the hottest parts and to seal the bearing chambers. Externally, it is piped to the aircraft, where it supplies many services, which we will list next. In the scene you can see the bleed duct leaving the HP compressor. But remember from the start that nothing is free. Every kilogram of air that is bled has had work done on it by the compressor, work paid for by the turbine and therefore by fuel, and yet it never passes through the combustor, the turbine and the nozzle to give thrust.
Part 1 · External users
The services bleed air supplies Engine compressor APU / ground cart Precooler and bleed valves pneumatic manifold Air conditioning and pressurisation (packs) Wing and engine anti-icing Hydraulic reservoir pressurisation Potable water tank pressurisation Air turbine motors: hydraulic pump, generator Thrust reverser actuation (some types) Fuel heaters Engine starting (cross-bleed) all bled from the compressor
Chapter 29 · Engine Bleed Air
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a modern turbofan aircraft, engine bleed air supplies a long list of services. The biggest user is the air conditioning and pressurisation system, through the packs. Then there is anti-icing of the wing leading edges and the engine intakes, and here hot air is used, which is the normal ice protection method on a modern jet. Bleed air also pressurises the hydraulic reservoirs and the potable water tanks. It can drive air turbine motors, which in turn drive a hydraulic pump or an electrical generator. On some types it actuates the thrust reversers, and it heats the fuel in the fuel heater. It is also used to start the engines, from the APU, a ground cart or another engine. All of this air goes into a pneumatic manifold, which can also be fed by the APU or a ground cart when the engines are not running.
Part 1 · External users
Bleed air around the aircraft Bleed ducts run from each engine through the pylon To the packs in the belly for air conditioning and pressurisation Along the wing leading edge for wing anti-icing Forward to the nacelle lip for engine anti-icing A crossbleed valve links the two sides; the APU feeds the same manifold Bleed ducts, seen from above crossbleed packs wing anti-ice wing anti-ice nacelle lip APU Engines and APU feed one pneumatic system
Chapter 29 · Engine Bleed Air
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the bleed air around the aircraft. From each engine, a bleed duct runs up through the pylon into the wing. Most of the air goes to the air-conditioning packs in the belly fairing, which condition it and feed the cabin for air conditioning and pressurisation. When wing anti-ice is selected, hot air flows along ducts inside the wing leading edge and heats the slats. Engine anti-ice takes air forward to the nacelle lip, so ice cannot form on the intake. A crossbleed valve links the left and right sides, so one engine, or the APU, can supply both, for example for engine starting. On the ground, the APU feeds the same pneumatic manifold. Watch the scene: the packs, then the wing, then the nacelle lip light up as each user is supplied.
Part 2 · Control
LP and HP bleed ports 50 60 70 80 90 100 0 100 200 300 400 500 600 Engine speed N2 (%) port pressure (kPa above ambient) pressure the systems need HP valve OPEN (low power, or anti-ice on) HP valve shut: LP port alone HP stage LP (intermediate) stage Two bleed ports LP port: used all the time; enough on its own at high power HP port: opens at low power (idle descent, taxi) to keep pressure and flow up Anti-ice selected: HP valve scheduled open, because higher pressure air is hotter Continuous LP bleed, supplemented by HP bleed when needed. The HP valve is always scheduled open when anti-icing is selected .
Chapter 29 · Engine Bleed Air
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
For external use, air is normally bled from two places: a continuous low pressure bleed, taken from an intermediate stage, or the outlet of the LP compressor, and a high pressure bleed from the HP compressor, used when needed. The graph shows why. Both port pressures rise with engine speed, but the HP port is always higher. At high power the LP port alone gives enough pressure for the air conditioning and pressurisation, so the HP valve stays shut. At low power, for example in an idle descent or taxiing, LP bleed pressure falls below what the systems need, so the HP valve opens to keep up pressure and flow. And whenever airframe anti-icing is selected, the HP valve is scheduled open, because now the requirement is for heat, and the higher the pressure of the bleed, the higher its temperature.
Part 2 · Control
Why higher pressure means hotter air 1 5 10 15 20 25 30 0 100 200 300 400 500 600 Pressure ratio at the bleed port air temperature (°C) sea level, ISA (+15 °C) FL350, ISA (−54 °C) Worked example LP port, ratio 8, sea level 288 K × 8^0.32 ≈ 284 °C HP port, ratio 25, sea level 288 K × 25^0.32 ≈ 527 °C LP port at FL350 219 K × 8^0.32 ≈ 151 °C So higher pressure = hotter air and precooling is always needed Simple model: polytropic efficiency 0.9 Compressing air heats it: the higher the pressure ratio at the port, the hotter the bleed. Cold air at altitude gives cooler bleed for the same ratio.
Chapter 29 · Engine Bleed Air
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why is high pressure air hotter? Because compressing air heats it. Work is done on the air, and its temperature rises with the pressure ratio. The graph uses a simple compressor model. At sea level in standard conditions, air from a port with a pressure ratio of eight comes out at about two hundred and eighty degrees Celsius. From a port with a ratio of twenty-five, it is over five hundred degrees. At flight level three five zero the inlet air is much colder, minus fifty-four, so the same ratio of eight gives only about one hundred and fifty degrees. So whenever heat is what we want, as for anti-icing, the HP port is the source. It also explains why bleed air is always too hot to use as it comes: it has to be cooled before it is piped through the aircraft, and that is the job of the precooler.
Part 2 · Control
The bleed valves LP (intermediate) port: a non-return valve stops HP air flowing back into the LP stage HP valve : opens at low power or for anti-ice; designed to open slowly and close quicklyEngine bleed valve (pressure regulating and shut-off): isolates the engine from the aircraftIt is closed from the bleed air panel , and by the fire handle Also closes automatically on duct overheat or over-pressure Engine bleed valves HP compressor LP (IP) stage HP stage NRV HP valve bleed valve precooler fan air to aircraft stops HP air flowing back into the LP stage isolation, pressure regulation; shut by the fire handle Closed from the bleed panel, or automatically on overheat, over-pressure or fire
Chapter 29 · Engine Bleed Air
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the main valves. Air from the LP, or intermediate, port passes a non-return valve, which stops high pressure air flowing back into the LP stage when the HP valve is open. The HP valve, sometimes called the high pressure shut-off valve, opens when LP pressure is too low, or for anti-ice. It is designed to open relatively slowly, to avoid a surge of pressure in the ducts, and to close quickly. Watch the scene: at low power the HP valve is open and HP air flows; when the engine goes to high power, the HP valve closes and the LP port supplies everything. Downstream, the engine bleed valve, a pressure regulating and shut-off valve, isolates the engine from the aircraft. The crew can close it from the bleed air panel, it closes when the fire handle is pulled, and it closes automatically on duct overheat or over-pressure.
Part 2 · Control
The precooler Bleed air may be several hundred °C : too hot for the wing ducts and the packs The precooler is an air-to-air heat exchanger, usually in the pylon Cooled by fan air , metered by a fan air valve , to a set temperature (about 200 °C) Fan air also cools the CSD/IDG oil and engine oil on many installations Used fan air is dumped overboard Precooler: air-to-air heat exchanger bleed air up to ~500 °C to the aircraft about 200 °C fan air in (fan air valve modulates) warmed fan air overboard Fan air also cools the generator drive (CSD/IDG) oil and engine oil coolers on many installations
Chapter 29 · Engine Bleed Air
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bleed air can be several hundred degrees Celsius, far too hot to pipe through the wing, near fuel tanks, or into the packs. So before it enters the aircraft, it passes through a precooler, an air-to-air heat exchanger usually mounted in the pylon. The cooling air is fan air, taken from the bypass duct. A fan air valve meters it to hold the bleed air at a set temperature, typically around two hundred degrees. Watch the scene: as the fan air valve opens, more cool air flows through the matrix and the duct temperature falls. The warmed fan air is dumped overboard. Fan air is useful elsewhere too: on many installations it also cools the oil of the generator drive, the C S D or I D G, and the engine oil coolers.
Part 2 · Control
Isolating the bleed air All bleed can be shut off by the isolation (engine bleed) valve from the bleed air panel It is also closed by the fire handle Pack flow control valves control the air into the cabinA pack can be shut if it fails, particularly with smoke in the cabin Close engine and APU air-conditioning bleeds during ground de-icing : toxic fumes Shutting the bleed air off Engine bleed (isolation) valve bleed panel switch; closes automatically when the fire handle is pulled Pack flow control valves control air into the cabin; shut a pack if it fails, especially smoke in the cabin Ground de-icing engine and APU air-conditioning bleeds closed: no de-icing fluid fumes in the cabin Bleed valves also close on duct overheat or over-pressure
Chapter 29 · Engine Bleed Air
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bleed air must be able to be shut off. All of the bleed from an engine can be stopped by the isolation valve, the engine bleed valve, operated from the bleed air control panel on the flight deck. The same valve is closed when the fire handle is operated, so that a fire cannot feed smoke and fumes into the ducts. Control of bleed air into the cabin is by the pack flow control valves. They let the crew control the air-conditioning system selectively and shut off an individual pack if it malfunctions, particularly when there is smoke in the cabin. One more rule: during ground de-icing, the air-conditioning bleeds from the main engines or the APU should be closed, to prevent fumes from the de-icing fluid being drawn into the cabin, as they are toxic.
Part 3 · The cost
What bleeding does to the engine Cause and effect Air bled from the compressor Less mass flow through the turbine Less thrust and EPR for the same fuel More fuel to restore the thrust Less air to cool the combustion gases Thrust ↓ EPR ↓ EGT ↑ RPM ↑ SFC ↑ Typical effects of bleed (e.g. anti-ice ON) Worked example: SFC Cruise, bleed for packs only 3 000 kg/h for 12 000 daN SFC 3 000 ÷ 12 000 = 0.250 kg/h per daN Anti-ice ON, same thrust fuel rises to 3 150 kg/h New SFC 3 150 ÷ 12 000 = 0.2625 Change +5 %: same thrust costs more fuel Figures illustrative; the trend is the exam point For a given thrust lever position: thrust and EPR fall ; to keep thrust, EGT, RPM and SFC rise .
Chapter 29 · Engine Bleed Air
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the cost. When air is bled from the compressor, the mass flow through the rest of the engine falls. Less air passes through the turbine and nozzle, so for the same fuel the thrust falls, and so does the engine pressure ratio, E P R. There is also less air to cool the combustion gases, so their temperature rises. To get the thrust back, more fuel is needed, which raises the exhaust gas temperature, the RPM and the specific fuel consumption. So, for the exam: bleeding air increases EGT, RPM and SFC, and reduces EPR and thrust. Look at the worked example. In the cruise, three thousand kilograms per hour gives twelve thousand decanewtons. With engine anti-ice on, holding the same thrust needs three thousand one hundred and fifty, so the specific fuel consumption rises by five per cent. The figures are illustrative; the direction of every change is what you must learn.
Part 3 · The cost
Low pressure, high volume Air conditioning and pressurisation need a large volume of air at modest pressure So engine air for the packs is essentially low pressure, high volume The LP stage gives plenty of air with less work done on it: cheaper in fuel HP air is hot and expensive : used only when LP air is not enough, or for anti-ice That is why the HP valve closes as soon as the LP stage can cope What the packs need Low pressure, high volume LP stage: plenty of air, moderate pressure and heat High pressure, low volume HP stage: hot, high pressure, costly in fuel Cabin air is essentially low pressure, high volume HP air is used only when the LP stage cannot cope
Chapter 29 · Engine Bleed Air
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
What kind of air do the packs actually need? The cabin needs a large volume of fresh air every minute, but only at a modest pressure, enough to push it through the packs and pressurise the hull. So the air obtained from the engine for air conditioning is essentially low pressure and high volume. That suits the LP stage: it supplies plenty of air, and less work has been done on it, so it is cheaper in fuel. High pressure air from the last stages is hot and expensive, because the compressor has done a lot of work on every kilogram. It is used only when the LP stage cannot supply enough pressure, at low engine power, or when heat is needed for anti-icing. That is why the HP valve closes again as soon as the LP port can cope on its own.
Part 4 · Internal air
The internal air system: as early a stage as possible 0 2 4 6 8 10 12 0 100 200 300 400 500 600 Bleed after compressor stage work put into each kg (kJ) stage 4: 125 kJ/kg, 3.1 : 1 stage 12: 563 kJ/kg, 30.0 : 1 Take it as early as possible A 12-stage compressor, ratio 30 : 1 (simple model) Air from stage 4 has had about 125 kJ/kg of work put in; air from stage 12 about 563 kJ/kg Use the earliest stage whose pressure can still do the job Return it to the gas stream at the highest pressure possible
Chapter 29 · Engine Bleed Air
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Air for internal use cools the combustion chamber liners and the turbine blades, and seals the bearing chambers and the turbine disc areas. A lot of work is done on air to raise its pressure as it passes through the compressor, and the graph shows how fast that work builds up. In this simple twelve-stage compressor with a pressure ratio of thirty, air taken after stage four has had about one hundred and twenty-five kilojoules of work put into each kilogram; air from the last stage, about five hundred and sixty. So it is logical to take internal air from as early a stage as possible, consistent with it having enough pressure to do its job. When the air has done its work, it is either dumped overboard, or ejected into the main gas stream at the highest possible pressure, which recovers a little of the performance.
Part 4 · Turbine cooling
Why cool the turbine? A gas turbine is a heat engine: high efficiency needs a high turbine entry temperature The limit is set by the materials of the turbine blades and nozzle guide vanes With continuous cooling they can work in gas hotter than their melting point Turbine discs are heated by conduction from the blades: they must be cooled too Main parts needing cooling: the combustion chamber and the turbine 1200 1400 1600 1800 2000 0 200 400 600 800 Turbine entry temperature (K) work per kg of air (kJ) blade alloy melts 399 kJ 649 kJ Raising TET from 1400 K to 1800 K gives 63 % more work from every kilogram of air (ideal cycle, ratio 30) Only cooling lets the gas run hotter than the metal can stand
Chapter 29 · Engine Bleed Air
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The main parts of the engine that need cooling are the combustion chamber and the turbine. We met combustor cooling earlier, so here we concentrate on the turbine. A gas turbine is a heat engine, and its efficiency and power depend on a high turbine entry temperature. The graph shows the ideal work from each kilogram of air at a pressure ratio of thirty: raising the turbine entry temperature from fourteen hundred to eighteen hundred kelvin gives about sixty per cent more. But there is a limit, set by the materials of the turbine blades and nozzle guide vanes. If these parts are cooled continuously, the gas around them can be hotter than the melting point of the metal they are made from. The turbine discs are heated by conduction from the blades, so they must be cooled too, or continued thermal stress could make them disintegrate.
Part 4 · Turbine cooling
How turbine blade cooling developed Uncooled solid blade early engines allowable gas temperature Single pass, internal LP air once through keeps below creep limit allowable gas temperature Multi-feed HP and LP air hotter gas allowed allowable gas temperature + Film cooling holes at LE and TE cool boundary layer allowable gas temperature Quintuple pass multi-feed + extensive film state of the art allowable gas temperature LP compressor air HP compressor air film-cooling holes Cooling air for the blades comes from the compressor : originally LP air only, later HP air as well .
Chapter 29 · Engine Bleed Air
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Turbine blade cooling has developed in steps. Early blades were uncooled. The first cooled blades passed low pressure compressor air once through the blade, single pass internal cooling, which kept the metal below the temperature at which excessive creep would occur. As engines needed more power and efficiency, gas temperatures rose, and LP air alone was not enough. Passing high pressure compressor air through the blade as well as LP air, called multi-feed, allowed a reasonable rise in gas temperature. Film cooling added more: air leaves through small holes in the leading and trailing edges and forms a protective boundary layer. Then designers found that passing the air through the blade several times cools it more, and the optimum was five passes. Quintuple pass, multi-feed internal cooling with extensive film cooling is today’s state of the art. In every case, the cooling air comes from the compressor.
Part 4 · Turbine cooling
Film cooling Cooling air leaves through small holes in the leading and trailing edges It forms a boundary layer of cool air over the surface The layer shields the blade from the hot gases from the combustor Combined with internal passages: multi-pass, multi-feed The cooling air comes from the HP compressor , routed internally Film cooling hot gas from the combustor a blanket of cool air on the surface internal passages Cooling air leaves through rows of tiny holes at the leading and trailing edges It forms a cool boundary layer that shields the metal from the hot gas stream Used on blades and nozzle guide vanes
Chapter 29 · Engine Bleed Air
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look more closely at film cooling. The cooling air that has passed through the internal passages of the blade leaves through rows of tiny holes, mainly at the leading edge, where the hot gas strikes hardest, and at the trailing edge, which is thin and hard to cool from inside. As it comes out, this air spreads along the surface and forms a boundary layer, a thin blanket of relatively cool air between the hot gas and the metal. To some extent, this layer protects the blade from the onslaught of the hot gases coming from the combustion chamber. Combined with multiple passes inside the blade and air fed from both compressors, it is what lets modern turbines run so hot. The same technique is used on the nozzle guide vanes, which come next.
Part 4 · Turbine cooling
Nozzle guide vanes and turbine discs casing hot gas → NGV HP blade NGV LP blade disc disc HP air to NGV HP air on both disc faces blade cooling seal seal seal used air into the gas stream NGVs: cooled like the blades, but with HP air only , plus film cooling. Discs: HP air on the front and rear faces , cavity pressures set by interstage seals .
Chapter 29 · Engine Bleed Air
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The nozzle guide vanes are cooled in much the same way as the turbine blades, with one major difference: only high pressure compressor air is used, supplemented by film cooling. They sit right at the exit of the combustor, in the hottest gas of all, so they need the highest pressure air to push through their passages and out of the film holes against the gas pressure. The turbine discs carry the blades. Heat conducted from the blades into the discs must be removed, otherwise uncontrolled expansion and contraction would cause thermal fatigue. So high pressure compressor air flows over the front and rear faces of each turbine disc, and the actual pressure in each disc cavity is controlled by interstage seals. Once it has done its job, this HP cooling air is ejected into the gas stream.
Part 4 · Turbine cooling
Active clearance control Cooling air can also control the turbine blade tip clearance It controls the temperature of the turbine casing , so the casing size Cooled casing shrinks: smaller gap , less leakage, better efficiency in the cruise Some engines also cool the compressor rotor with bleed air That controls its thermal growth and improves compressor efficiency Active clearance control Valve shut (take-off) tip gap casing hot: expanded Valve open (cruise) tip gap casing cooled: shrinks Cooling air (often fan air) is sprayed on the turbine casing The casing shrinks onto the blade tips: smaller tip clearance Less gas leaks round the tips: better efficiency, lower SFC Some engines also cool the compressor rotor with bleed air to control its thermal growth
Chapter 29 · Engine Bleed Air
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some modern turbofans use cooling air for another clever purpose: active clearance control. Gas that leaks round the tips of the turbine blades does no work, so the smaller the tip clearance, the better the efficiency. But clearances must be generous at take-off and during rapid changes of power, when the parts expand at different rates. So in the cruise, cooling air, often fan air, is sprayed on the outside of the turbine casing. The casing cools and shrinks, closing the gap round the blade tips, and the specific fuel consumption improves. When the valve shuts, the casing grows again and the clearance opens up. A related feature on some engines is selective cooling of the compressor rotor with bleed air, which controls the thermal growth of the compressor blades and so improves compressor efficiency.
Part 4 · Sealing
Labyrinth seals Most engine seals work on the labyrinth (maze) principle Fins rotate close to a static ring of abradable material or honeycomb , or within an annulus of oil On first running, the fins cut their own groove : minimum clearance A pressure drop across each fin restricts the air flowing through At a bearing chamber the air flows inwards : no oil leaks out, and oil is helped back to scavenge Labyrinth seal at a bearing chamber rotating shaft abradable / honeycomb lining bearing chamber sealing air (higher pressure) air leaks INWARDS across each fin, a little pressure lost at each Fins on the shaft run very close to the static lining On first running they cut their own groove: minimum clearance The inward airflow stops oil leaking out and pressurises the chamber, helping oil return to scavenge No rubbing contact: no wear, no heat
Chapter 29 · Engine Bleed Air
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
To stop oil or air leaking where they should not, several kinds of seal are used, and most work on the labyrinth principle, a maze. Fins on the rotating part run very close to a static ring. The ring may be a soft abradable material or a honeycomb structure; when the engine is first run, the fins rub into it and cut their own groove, giving the minimum possible clearance. In another form, the fins rotate within an annulus of oil. As air passes each fin, there is a pressure drop, so the flow through the seal is restricted. At a bearing chamber, the air pressure outside is higher, so air flows inwards across the seal. That stops oil leaking out, and it also builds up a positive pressure inside the chamber, which helps push the oil back to the scavenge pump.
Part 4 · Sealing
Interstage seals: a worked example Interstage seals: the number of fins sets the pressure Supply cavity 500 kPa 2 fins Zone A 500 − 2 × 40 = 420 kPa 6 fins Zone B 500 − 6 × 40 = 260 kPa Simplified: an equal 40 kPa drop across each fin. Fewer fins into a zone = higher pressure there An interstage seal prevents or controls leakage between engine sections at different pressures . More fins = more pressure dropped.
Chapter 29 · Engine Bleed Air
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
An interstage seal is used to prevent or control leakage of air between sections of the engine that are working at different pressures. The pressure dropped across the seal depends on the number of fins the air must pass. So, to create a higher pressure in one zone than another, the designer simply makes the air pass over fewer fins on its way into the high pressure zone. Here is a simplified example, assuming an equal drop of forty kilopascals at each fin. A supply cavity is at five hundred kilopascals. Air reaching zone A crosses only two fins, so zone A sits at four hundred and twenty. Air reaching zone B crosses six fins, so zone B is at only two hundred and sixty. Real seals are not that linear, but the principle holds: fewer fins, less pressure lost, higher pressure in that zone.
Part 4 · Sealing
The intershaft hydraulic seal Some seals sit between two rotating shafts , e.g. the HP and LP shafts Shaft flexing would make fins rub an abradable lining: heat , even shaft failure Instead the fin rotates within an annulus of oil held by centrifugal force If a shaft deflects, the fin enters the oil and the seal is kept No undue friction or heat Intershaft hydraulic seal outer shaft (e.g. HP) inner shaft (e.g. LP) oil held in the annulus by centrifugal force fin dips into the oil Between two rotating shafts, flexing could make fins rub an abradable lining: heat, possible shaft failure Here the fin turns in a ring of oil: if the shafts flex, the seal is kept with no friction or heat
Chapter 29 · Engine Bleed Air
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where a seal has to sit between two rotating shafts, for example between the HP and LP shafts, the usual labyrinth with an abradable lining causes a problem. The shafts flex in operation, and the fins would rub hard against the lining, creating high temperatures and the possibility of a shaft failure. The answer is the intershaft hydraulic seal, an example of the oil-annulus type of labyrinth. One shaft carries a channel, and centrifugal force holds a ring of oil in it. A fin on the other shaft dips into this ring of oil. If either shaft deflects, the fin simply moves deeper into the oil or less deep, and the seal is maintained without generating any undue friction or heat. It is an elegant solution: a seal that cannot wear.
Part 4 · Sealing
Sealing air and oil loss Sealing air for bearing chambers comes from intermediate compressor stages It reaches the seals through transfer ports in the compressor rotor drum Seal efficiency depends on mechanical design and compressor bleed air pressure Greatest oil loss from a serviceable engine: low power , e.g. idle descent from high altitude At high power, oil loss is almost negligible Seal air pressure and oil loss 20 40 60 80 100 Engine power (% N2) relative sealing air pressure oil loss idle descent: greatest loss Sealing air comes from intermediate compressor stages, through transfer ports in the rotor drum Seal efficiency = mechanical design + air pressure At high power, oil loss is almost negligible
Chapter 29 · Engine Bleed Air
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Remember the rule: take internal air from as early a stage as possible. For the bearing chamber seals, the sealing air is taken from the intermediate stages of the compressor, through air transfer ports in the compressor rotor drum, and passed along internal passages to where it is needed. The efficiency of all these seals depends on two things: first, the mechanical design of the seal, and second, the air pressure, which is essential if the seal is to work at all. Now think about low power. At idle, for example during a long descent from high altitude, the compressor delivers much lower pressures, so the sealing air pressure is low, and that is when a serviceable engine loses the most oil. At high power settings, oil loss from a serviceable engine is almost negligible.
Part 4 · Disposal
Disposal of cooling and sealing air HP cooling air is ejected into the exhaust stream LP air leaves through its own dedicated vent pipe On some engines the vent air temperature is monitored to check the internal integrity Too hot: red I.E.O.H. warning, internal engine overheat IEOH requires a mandatory engine shutdown Where the used air goes exhaust stream HP cooling air LP air dedicated vent pipe temperature sensor I.E.O.H. Internal engine overheat: red warning Mandatory engine shutdown
Chapter 29 · Engine Bleed Air
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Finally, once the cooling and sealing air has done its job, it has to go somewhere. The high pressure air used for cooling the turbine is ejected into the exhaust stream, where it adds a little to the flow. The low pressure air is led out through its own dedicated vent pipe. On some engines, the temperature of the air leaving this vent pipe is monitored, because it gives an indication of the integrity of the engine’s internal construction. If something fails inside, a burst duct or a broken seal letting hot gas into the wrong place, the vent temperature rises. When it exceeds a predetermined maximum, a temperature sensor triggers a red warning light captioned I E O H, internal engine overheat. That warning requires a mandatory engine shutdown. It is not a case for monitoring, or for reducing to idle: the engine must be shut down.
Summary
Engine bleed air in eight lines Users Air conditioning and pressurisation, anti-ice (hot air) , reservoirs, water, ATMs, reversers, fuel heaters, starting
LP and HP LP bleed continuous; HP valve opens at low power and always for anti-ice (hotter)
Control NRV on LP port; precooler with fan air ; engine bleed valve shut by panel or fire handle
Cost Bleed: thrust and EPR ↓ ; EGT, RPM and SFC ↑ . Pack air is low pressure, high volume
Internal air Taken from the earliest stage possible; returned at high pressure or dumped overboard
Turbine cooling Blades: LP then HP air, film, quintuple pass. NGVs: HP air only . Discs: HP air both faces
Seals Labyrinth, interstage (different pressures), intershaft (oil annulus); air flows into bearing chambers
Oil and IEOH Most oil lost at idle . LP vent too hot: IEOH , mandatory shutdown
Chapter 29 · Engine Bleed Air
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Bleed air supplies air conditioning and pressurisation, anti-icing with hot air, reservoir and water pressurisation, air turbine motors, reversers, fuel heaters and engine starting. LP bleed is continuous, and the HP valve opens at low power and always for anti-ice, because higher pressure air is hotter. A non-return valve protects the LP port, a precooler uses fan air, and the engine bleed valve is shut from the panel or by the fire handle. Bleeding reduces thrust and E P R and raises EGT, RPM and SFC; air for the packs is low pressure, high volume. Internal air comes from the earliest possible stage. Blades use LP and HP air with film cooling; nozzle guide vanes use HP air only; discs get HP air on both faces. Seals are labyrinths, interstage for different pressures, intershaft with oil. Most oil is lost at idle, and an IEOH warning means shut the engine down.