Engines · Chapter 8
Carburettors How a float carburettor meters fuel: the U-tube and the venturi, float and needle, main jet and diffuser, slow running, mixture control, power enrichment, the accelerator pump and priming.
air in mixture to the cylinders © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter eight takes apart the float-type carburettor, the device that has fed most light aircraft engines for a century. It has one job: to mix fuel with the air the engine draws in, in the right proportion, at every power setting from idle to full throttle, at every altitude, and while the throttle is moving. We will build it up piece by piece, from two simple principles, the U-tube and the venturi, to the float chamber, the jets, the slow-running system, the mixture control, power enrichment, the accelerator pump and priming, and finish with the faults that exams love to ask about.
Chapter 8 · Roadmap
Building a carburettor, piece by piece 1 · Principles What it must do; U-tube and venturi; float, needle and main jet; the throttle.
2 · Keeping it accurate Balance duct and diffuser: the same mixture at every airflow.
3 · Slow running The idle jet at the throttle lip, flat spots and the idle cut-off.
4 · Mixture control Altitude richening; needle and air-bleed controls.
5 · Power enrichment Power jet and back-suction economiser: rich at high power, lean in cruise.
6 · Acceleration and starting Accelerator pump, choke, priming and the light aircraft fuel system; faults.
Chapter 8 · Carburettors
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan. We start with the principles: what a carburettor must do, the U-tube and the venturi, then the float, the needle valve, the main jet and the throttle. Next, two refinements that keep the mixture accurate: the pressure balance duct and the diffuser. Third, slow running, with its own jet at the edge of the throttle valve, the flat spots that appear when the change-over is poor, and the idle cut-off. Fourth, the mixture control, and why the carburettor needs one as you climb. Fifth, power enrichment, which makes the mixture rich at high power and economical in the cruise. Last, acceleration and starting, with the accelerator pump, the choke, priming and the fuel system, and a table of faults to finish.
Part 1 · Principles
What the carburation system must do Give the right air/fuel ratio at every throttle setting, from slow running to full power, and while accelerating and decelerating Work at all altitudes and temperatures in the operating range Make starting easy , and usually provide a way to cut off the fuel to stop the engine Float carburettor: cheapest and simplest, but very prone to icing and affected by manoeuvres Injection carburettor and fuel injection: more precise, less icing; injection gives the best distribution
Three ways to meter fuel
icing
manoeuvres
distribution
Float-chamber carburettor
cheapest, simplest
very prone
affected
fair
Injection (pressure) carburettor
meters precisely
less prone
less affected
good
Fuel injection
best distribution, economical
relatively free
unaffected
best
Diesels have no carburettor and an unthrottled air intake
Chapter 8 · Carburettors
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whatever the design, the carburation system has three jobs. It must deliver the right air to fuel ratio at every throttle setting, from slow running to full throttle, and it must keep doing so while the throttle is moving, during acceleration and deceleration. It must work at every altitude and temperature the aircraft will meet. And it must make starting easy, and normally give a way of shutting off the fuel to stop the engine. There are three common ways of doing this. The float-chamber carburettor is the cheapest and simplest and is used on many light aircraft, but it is very prone to icing and can be upset by manoeuvres. The injection, or pressure, carburettor meters fuel more precisely and is less affected by both. Direct fuel injection gives the best distribution, is reputed to be the most economical, and is relatively free from icing. Diesels have no carburettor at all.
Part 1 · Principles
The U-tube principle Liquid in a U-tube stands at the same level in both legs when both feel the same pressure Lower the pressure on one leg and the liquid flows towards it In the carburettor one leg is opened out into the float chamber , at air-intake pressure The other leg is the discharge tube , ending in the low pressure of the venturi throat The pressure difference between them drives the fuel
equal pressure
lower pressure on the right
In the carburettor:
float chamber
= wide leg at air pressure
venturi throat
= low-pressure leg
Chapter 8 · Carburettors
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The float carburettor relies on two simple principles, and the first is the U-tube. Bend a tube into a U and pour liquid in. If both legs feel the same air pressure, the liquid settles at the same level in each. Now reduce the pressure on one leg. The higher pressure on the other leg pushes the liquid round, so it rises in the low-pressure leg and, if the difference is big enough, flows out of the top. In the carburettor, one leg is opened out into a small tank, the float chamber, whose surface feels the pressure of the air intake. The other leg is the discharge tube, whose tip sits in the low pressure of the venturi throat. The difference between those two pressures is what drives fuel out into the airstream. No pump is needed at that point; the airflow does the work.
Part 1 · Principles
The venturi: faster air, lower pressure Bernoulli : along a streamline the total energy per unit mass is constantAt the narrow throat the air speeds up, so its static pressure and temperature fall The throat depression is a measure of the mass airflow into the engine Worked example: 30 → 60 m/s gives Δp ≈ 16.5 hPa , enough to lift fuel about 23 cm The venturi itself cools the air only about 1.3 °C here: fuel evaporation does far more
V₁ = 30 m/s
V₂ = 60 m/s
Δp = ½ρ(V₂² − V₁²) = ½ × 1.225 × (3600 − 900) ≈ 1654 Pa (16.5 hPa)
lifts fuel ≈ 23 cm · static temperature falls ≈ 1.3 °C
p₁ high
p₂ low
Chapter 8 · Carburettors
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The second principle is the venturi, a smooth narrowing in the carburettor barrel. Bernoulli tells us that along a streamline the total energy of each kilogram of air stays the same. So when the air speeds up through the narrow throat, its static pressure and its temperature must fall. That pressure drop, the depression at the throat, grows with the mass of air flowing, so it is a natural measure of the engine's airflow. Here are real numbers. Suppose air enters at thirty metres per second and the throat has half the area, so the air doubles to sixty metres per second. The pressure falls by about sixteen and a half hectopascals, enough to lift a column of fuel about twenty-three centimetres. The temperature falls only about one point three degrees. Remember that for icing: the venturi on its own cools the air only a little; evaporating fuel does most of the cooling.
Part 1 · Principles
The simple float-chamber carburettor
air in mixture to the cylinders
Chapter 8 · Carburettors
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole simple carburettor working. This is the updraft type: air enters at the bottom, drawn in by the engine's suction, and speeds up through the venturi, where its pressure falls. Fuel waits in the float chamber at the side, kept at a constant level by a float and a needle valve, with the chamber at air-intake pressure. A passage runs from the bottom of the chamber, through the calibrated main jet, to the discharge nozzle in the throat. The pressure difference pushes fuel through the jet and out of the nozzle as a spray, which the fast air breaks up and carries away. Above the venturi is the throttle, a butterfly valve that controls how much air, and therefore how much mixture, goes on to the cylinders. Notice the logic: the throttle controls air, the venturi senses it, and the jet meters fuel to match.
Part 1 · Principles
The float and needle valve Fuel arrives by gravity , an electric booster pump or an engine-driven pump ; a pump gives a positive supply to the float chamber As the level rises the float lifts and shuts the needle valve ; as fuel is used it drops and lets more in The level is held just below the nozzle lip , so fuel cannot spill out when the engine stops Level too high : rich, flooding. Level too low : weak Negative g and steep manoeuvres upset the float : the engine may starve or flood
needle valve
float
from pump or gravity
vent: air pressure
level just below the nozzle lip
Chapter 8 · Carburettors
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel reaches the float chamber by gravity, from an electric booster pump, or from an engine-driven pump. Where pumps are used, a fuel pressure gauge shows that they are working, and the engine-driven pump makes sure there is a positive flow of fuel to the float chamber, not to the nozzle. Inside the chamber, the float rides on the fuel. As the level rises, the float lifts and pushes the needle valve onto its seat, shutting off the supply. As the engine uses fuel, the float drops a little and the needle opens to top it up. The level is set just below the lip of the discharge nozzle, so that when the engine stops no fuel spills out. If the level is set too high the mixture is rich and the carburettor may flood; too low and it is weak. And because the float depends on gravity, negative g or violent manoeuvres can starve or flood the engine.
Part 1 · Principles
The main jet sets the mixture strength For a given pressure difference, the size of the main jet sets the fuel flow, and so the mixture The jet is the smallest orifice in the system: a strainer is fitted before it Partly blocked jet: less fuel, weak mixture, power loss, high temperaturesPunctured or enlarged jet: more fuel, rich mixture, RPM falls , black smokeFuel flow therefore depends on RPM, throttle position and mixture setting
The jet sizes the fuel flow for a given Δp
correct jet
design mixture
partly blocked
WEAK: power and RPM fall, hot
punctured / enlarged
RICH: RPM falls, black smoke
strainer BEFORE the jet: the smallest orifice
Chapter 8 · Carburettors
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The main jet is a carefully calibrated hole in the fuel passage. For any given pressure difference across it, its size decides how much fuel flows, and therefore how strong the mixture is. It is the smallest opening in the whole fuel system, so a speck of dirt can block it. That is why a strainer is fitted just before the jets. Now think about faults. A partly blocked jet passes less fuel, so the mixture goes weak: power falls and temperatures rise. A jet that has been punctured or enlarged passes too much fuel, so the mixture goes rich, the R P M drops and you may see black smoke. Putting it together, the fuel flow to a carburettor engine depends on the R P M and the throttle position, which together set the airflow, and on the mixture setting. All three, not just one.
Part 1 · Principles
The throttle and manifold pressure The throttle valve (butterfly) above the venturi controls the airflow , and so the mass of charge More charge mass per minute = more power Opening the throttle raises manifold pressure : from about 12 inHg at idle to near ambient at full throttle Faster airflow deepens the venturi depression , drawing more fuel to match Exam point: induction manifold pressure increases as the throttle opens
throttle valve
manifold
shut
half
full
0
10
20
30
throttle opening
manifold pressure, inHg
outside air 29.92
idle ≈ 12
opening the throttle RAISES
manifold pressure
Chapter 8 · Carburettors
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The throttle valve is a butterfly in the barrel above the venturi, connected to the pilot's throttle lever. It controls the airflow, and so the mass of charge that reaches the cylinders each minute; the greater that mass, the greater the power. Watch the scene as the throttle swings open. The airflow increases, the air in the throat speeds up, the depression there deepens and the column on the right shows the throat pressure falling, so more fuel is drawn out to match. Now a favourite exam point. Above the throttle, in the induction manifold, the pressure behaves the other way. With the throttle nearly shut the engine is sucking against a restriction, so manifold pressure is low, perhaps twelve inches of mercury at idle. As you open the throttle the restriction is removed and manifold pressure rises towards the outside air pressure. So opening the throttle increases manifold pressure.
Part 2 · Keeping it accurate
The pressure balance duct Correct metering needs the float chamber and the air intake at the same pressure A simple vent hole in the cover feels only the local pressure under the cowling Ram effect and manoeuvres change intake pressure, which a vent would not pass on So a balance duct connects the float chamber directly to the air intake It also feeds air to the diffuser and, on some carburettors, the altitude mixture control
pressure balance duct from the air intake
float chamber at intake pressure
Chapter 8 · Carburettors
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The U-tube only works properly if the float chamber feels the same pressure as the air entering the carburettor. A drilling in the float chamber cover, open to the air under the cowling, is not good enough. At speed, and during manoeuvres, the pressure at the air intake changes with ram effect and with the local flow, and a simple vent would not pass those changes to the fuel. The metering would drift. The answer is the pressure balance duct, which connects the space above the fuel directly to the air intake. Now any change of intake pressure acts equally on the air flowing through the venturi and on the fuel in the chamber, and the mixture stays correct. The same duct also supplies air to the diffuser, and in some carburettors it is part of the altitude mixture control.
Part 2 · Keeping it accurate
Why a plain carburettor gets richer as airflow rises
10%
20%
40%
60%
80%
100%
8:1
10:1
12:1
14:1
16:1
18:1
20:1
22:1
Airflow through the carburettor (fraction of full)
Air : fuel ratio from the main jet (up = weaker)
plain carburettor: richer and richer
with air-bleed diffuser: nearly constant
too little
depression
← slow-running system needed
Computed: fuel needs a minimum depression to reach the nozzle lip, then flows more freely as the depression grows. Two fixes follow: the diffuser and the slow-running system .
Chapter 8 · Carburettors
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph explains why the simple carburettor needs help. Along the bottom is the airflow, and up the side the mixture coming from the main jet. At very low airflow the throat depression is too weak even to lift the fuel up to the nozzle lip, so the main jet gives nothing at all; that is why a separate slow-running system is needed. Just above that, the mixture is very weak. Then, as the airflow rises, the plain carburettor, the red line, gets richer and richer. Air and fuel are different fluids, a light gas and a dense liquid, and the fuel flows more freely through the jet as the pressure difference grows, so the proportion of fuel to air rises. At full airflow the plain design would be down near ten to one. The green line shows the same carburettor with an air-bleed diffuser: almost flat across the range. Let us see how it does that.
Part 2 · Keeping it accurate
The air-bleed diffuser A small hole in a tube that is lifting liquid lets air bleed in : the liquid rises in drops, not a solid column The bleed reduces the pressure difference acting on the fuel and slows its flow Diffuser well: as airflow rises the fuel level in the well falls and uncovers more air holes More air bleeds in just when the plain carburettor would richen: the mixture is held constant Bonus: the fuel leaves emulsified with air, so it vaporises better, especially at low RPM
low airflow
holes covered
high airflow
4 air holes open
Chapter 8 · Carburettors
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The diffuser is based on a neat bit of physics. If you suck liquid up a tube, a column rises. Make a small hole in the side of the tube, and air bleeds in through the hole; the liquid now rises as a frothy mixture of drops and bubbles, and the air bleeding in reduces the force acting on the liquid, so less of it flows. In a carburettor, the discharge tube stands in a diffuser well with rows of small air holes, fed with air from the balance duct. At low airflow the fuel covers most of the holes. As the airflow and the depression rise, fuel is drawn from the well faster than it refills, its level falls and more holes are uncovered. More air bleeds in, limiting the pressure difference on the fuel exactly when the plain carburettor would start to richen. So the primary job of the diffuser is to control the mixture strength over part of the engine speed range.
Part 3 · Slow running
The slow-running system At idle the airflow is tiny: the venturi depression cannot lift fuel through the main jet But just above the nearly closed throttle there is a strong depression A slow-running passage with its own jet runs from the float chamber to an outlet at the lip of the throttle valve The jet is sized for the rich mixture needed at idle; an air bleed helps atomise it A transverse passage through the throttle spreads the mixture across the manifold
idle outlet at the throttle lip strong depression here
slow-running jet
air bleed
main nozzle: no flow
Chapter 8 · Carburettors
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
At idle the engine draws so little air that the venturi depression is far too weak to lift fuel through the main jet. Yet just above the almost-closed throttle valve, the engine is sucking hard against a small gap, so there is a strong depression there. The slow-running system uses it. A separate passage, with its own slow-running jet, leads from the float chamber to an outlet right at the lip of the throttle valve. The strong suction there draws fuel out. The jet is sized to give the rich mixture that idling needs, remember the reasons from the last chapter, and an air bleed opening into the barrel below the throttle mixes air with the fuel to help atomise it. In some designs a transverse passage drilled through the throttle valve itself, with its own small bleed hole, spreads the idle mixture evenly across the induction manifold.
Part 3 · Slow running
The change-over and flat spots
0
20
40
60
80
100
Throttle opening, %
Fuel flow (relative)
flat spot
(weak)
slow-running system
main jet
total delivered
fuel needed (dotted)
A flat spot : poor response to throttle opening caused by a temporary weak mixture , felt as a hesitation while accelerating.
Chapter 8 · Carburettors
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now open the throttle slowly from idle. As the throttle plate swings away, the depression at its lip falls, so the slow-running system delivers less and less, the blue dashed line. At the same time the airflow through the venturi grows, and at some point the throat depression becomes strong enough to lift fuel through the main jet, the gold dashed line. The total, in red, is what the engine actually gets. If the two systems are not carefully blended, there is a gap where the idle system has faded and the main system has not yet taken over, and the mixture goes temporarily weak. That gap is a flat spot: a hesitation, a moment of poor response to the throttle, as you accelerate. Carburettors are tuned to give a smooth, progressive change-over from one system to the other so that the flat spot disappears.
Part 3 · Slow running
Stopping the engine: idle cut-off A cut-off valve in the slow-running passage (often part of the mixture lever ) shuts off the fuel The mixture becomes progressively weaker until it will not burn, and the engine stops No running on : hot spots cannot keep igniting a mixture that is not there (pre-ignition) No raw fuel left to condense and wash the oil off the cylinder walls Then switch the magnetos off
cut-off valve CLOSED
no fuel
Why stop the engine with the mixture, not the magnetos?
No running on
hot spots cannot keep firing an unburnable mixture
Dry cylinders
no raw fuel left to condense and wash the oil off the walls
Safe ground handling
no combustible charge left in the manifold
Chapter 8 · Carburettors
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
How should you stop a piston engine? Not by switching off the magnetos first, but by cutting off the fuel. A cut-off valve, usually built into the mixture control and selected by pulling the lever fully back, closes the fuel passage. Watch the scene: the mixture lever goes to cut-off and the fuel stops. The mixture reaching the cylinders gets progressively weaker until it will no longer burn, and the engine stops. This has two big advantages. First, there is no chance of the engine running on erratically, with hot spots in the cylinders igniting the charge after the ignition is off; that would be pre-ignition. Second, no raw fuel is left behind to condense in the cylinders and wash the oil off the cylinder walls, which would leave them unlubricated at the next start. Only once the engine has stopped are the magnetos switched off.
Part 4 · Mixture control
Altitude, and the needle-type mixture control As altitude increases, air density falls : less mass of air for the same throttle Venturi depression falls, but fuel flow does not fall as much : the mixture becomes richer A mixture control lets the pilot correct this for economy Needle type: a cockpit lever raises or lowers a needle in the orifice feeding the main jet Fully down, the needle blocks the fuel : a way to stop the engine
mixture needle up = rich · down = weak · fully down = cut-off
main jet
Chapter 8 · Carburettors
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
As the aircraft climbs, the air gets thinner, so for the same throttle opening a smaller mass of air enters the engine. The depression in the venturi falls too, but the fuel flow it produces does not fall by the same proportion, so the mixture becomes progressively richer with height. That is unacceptable for economy and it fouls the plugs, so the pilot needs a mixture control. The commonest is the needle type. A cockpit lever is connected to a needle in the float chamber, sitting in the orifice that feeds the main jet. Raising the needle opens the orifice and enriches the mixture; lowering it restricts the flow and weakens it. In the scene the lever lowers the needle part-way. Pushed fully down, the needle blocks the fuel to the main jet altogether, which gives a way of stopping the engine.
Part 4 · Mixture control
The air-bleed mixture control Controls the air pressure in the float chamber , and so the pressure difference on the fuel A small bleed links the float chamber to the venturi , tending to lower chamber pressure A valve worked by the cockpit lever admits intake air to the chamber Valve fully open : chamber pressure highest: full rich . Closing it: lower pressure, weaker Idle cut-off : chamber linked to the engine side of the throttle: fuel stops
Valve fully OPEN
chamber at intake pressure
FULL RICH
Valve part CLOSED
bleed to the venturi lowers pressure
WEAKER
IDLE CUT-OFF
chamber linked to the manifold
FUEL STOPS
Chapter 8 · Carburettors
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The air-bleed mixture control, sometimes called a back-suction control, does the same job a different way: it changes the air pressure above the fuel rather than the size of a fuel orifice. A small bleed connects the float chamber to the venturi, which tends to pull the chamber pressure down. A valve, worked by the cockpit lever, lets intake air into the chamber to hold the pressure up. With the valve fully open, chamber pressure is at its highest, the pressure difference on the fuel is greatest and the mixture is fully rich. As the valve closes, the bleed to the venturi wins, chamber pressure falls, less fuel flows and the mixture weakens. In the idle cut-off position the valve connects the float chamber to the manifold on the engine side of the throttle. The pressure there is so low that fuel stops flowing altogether, and the engine stops.
Part 5 · Power enrichment
Power enrichment: the power jet Above cruise power a richer mixture is needed to prevent detonation An extra jet, the power jet , enrichment jet or economiser , adds fuel Its needle is linked to the throttle : shut below maximum cruise power, opening progressively, fully open at full throttle Some engines open it with a sealed bellows worked by manifold pressure , linking enrichment to power Alternative: set rich for power, then bleed float-chamber pressure for the cruise
main jet: always
power jet needle
linked to the throttle (or MAP bellows)
0
25
50
75
100
shut
full
throttle / power, %
power jet opening
closed below max cruise
Chapter 8 · Carburettors
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
At power settings above the cruise range, the engine needs a richer mixture, not for power but to keep detonation away. There are two ways of providing it. One is an additional fuel supply. The other is to set the carburettor rich for high power and then reduce the fuel for cruising by bleeding off float-chamber pressure, which we will see next. The first method uses an extra jet, called the power jet, the enrichment jet or, rather confusingly, the economiser. Its needle valve is linked to the throttle. It stays fully closed at every throttle setting below that for maximum cruise power at sea level; above that it opens progressively, and at full throttle it is fully open. On some engines the power jet is opened instead by a sealed bellows that responds to manifold pressure, so that the enrichment follows the actual engine power rather than the throttle position.
Part 5 · Power enrichment
The back-suction economiser A channel with an air jet links the float chamber to the barrel at the throttle valve High power , throttle wide open: pressure there is only slightly below atmospheric: little effect , mixture rich Cruise , throttle part-closed: fast air past its edge creates suction That suction lowers float-chamber pressure , reducing main-jet flow: economical mixture Automatic: no pilot action needed
Cruise: throttle part-closed
chamber pressure down → ECONOMICAL
High power: throttle wide open
little suction → RICH
economiser channel from the float chamber to the throttle edge
Same idea in reverse as the power jet: rich at high power, lean at cruise
Chapter 8 · Carburettors
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The back-suction economiser is the air-operated way of getting a rich mixture at high power and an economical one in the cruise. A channel, with a small air jet in it, connects the top of the float chamber to the carburettor barrel right beside the throttle valve. At high power the throttle is wide open, and the air flowing past it is only slightly below atmospheric pressure. That has very little effect on the float chamber, so the full pressure difference acts on the fuel and the mixture is rich. Now close the throttle to the cruise position. Air rushing through the narrow gap at the edge of the plate creates a suction, and the channel applies that suction to the float chamber. The chamber pressure falls, the pressure difference across the main jet is reduced, less fuel flows, and the engine gets the economical mixture it needs for cruising. It is all automatic.
Part 6 · Acceleration and starting
The accelerator pump Snap the throttle open: the air responds almost at once , but the fuel lags behind Result: a temporary weak mixture , a flat spot , or at worst a weak cut The accelerator pump , linked to the throttle, squirts fuel into the venturi when it is opened A controlled bleed past the piston : a slow opening passes no extra fuel Some have a delayed-action plunger , adding fuel for a few seconds after the movement stops
accelerator pump plunger driven by the throttle
Throttle snapped open:
air responds at once,
fuel lags behind
0
1
2
3
4
8:1
13:1
20:1
seconds
air : fuel ratio (up = weaker)
no pump: weak cut / flat spot
with pump
Chapter 8 · Carburettors
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Suppose you snap the throttle open. Air is light and responds almost at once, so the airflow jumps. Fuel is heavy, and the metering system takes a moment to catch up. For that moment the mixture goes weak, giving a flat spot, a hesitation, or at worst a weak cut where the engine falters. The cure is the accelerator pump. It is a small plunger in a fuel-filled cylinder, linked directly to the throttle. Watch the scene: when the throttle is opened quickly, the plunger is driven down and squirts a shot of fuel straight into the venturi, covering the gap until the main system catches up. A controlled bleed past the pump piston means that a slow throttle movement just lets fuel leak back, with no extra fuel delivered. Some pumps also have a delayed-action plunger that keeps adding a little fuel for a few seconds after the throttle stops moving.
Part 6 · Acceleration and starting
Choke tube or choke valve? Choke tube is the British name for the venturi : it lowers static pressure to draw in fuelA choke (strangler) valve is a plate in the air intake, below the venturi Shutting it cuts the air and greatly enriches the mixture for a cold start Most aero engines use a primer instead; the choke is rare in aircraft Exam trap: "the choke tube decreases static pressure to draw in fuel"
CHOKE TUBE = venturi lowers static pressure
choke (strangler) valve shut for a cold start
Chapter 8 · Carburettors
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The word choke causes confusion, so let us clear it up. In British usage the choke tube is simply the venturi, the narrow part of the barrel. Its job is to decrease the static pressure so that fuel is drawn in. It does not increase the pressure, and it does not warm the air. A choke valve, or strangler, is something different: a plate in the air intake below the venturi. Watch the scene as it is shut. It cuts the airflow, so the depression at the nozzle grows and the mixture becomes very rich, which helps a cold engine start. Cars used to have them; most aero engines use a priming pump instead, so a choke valve is rare in aircraft. In the exam, when you read choke tube, think venturi: it decreases static pressure to draw in fuel.
Part 6 · Acceleration and starting
Priming and the light aircraft fuel system A priming pump sprays fuel into the induction manifold , close to the inlet valves On many light aircraft the primer takes fuel from the filter housing Without a primer, some aircraft allow priming by pumping the throttle (the accelerator pump) Otherwise discouraged: fuel pools in the intake and raises the risk of a carburettor fire A primer left unlocked can make the idle mixture too rich
left tank
right tank
SEL
filter + drain
pump
carb
primer
induction manifold
near inlet valves
drains
Chapter 8 · Carburettors
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
For a cold start the engine needs extra fuel vapour right where it will be drawn in. A priming pump, a small hand plunger on the panel, sprays fuel directly into the induction manifold, close to the inlet valves. Here is a typical light aircraft system: wing tanks with water drains, a selector valve, a filter with its own drain, a mechanical or electric pump, and the carburettor. The primer takes its fuel from the filter housing. If there is no primer, some aircraft allow you to prime by pumping the throttle a few times, which works the accelerator pump. Do not make a habit of it, though. The extra fuel pools in the carburettor and air intake, and if the engine backfires during the start it can set fire to it: a carburettor fire. And a primer that is not locked after use can keep feeding fuel, giving an overly rich mixture at slow running.
Exam focus
Carburettor faults and what they cause Fault or condition Effect on mixture What the pilot notices Main jet punctured or enlarged Rich RPM falls, rough running, black smoke Main jet partly blocked Weak Power and RPM fall, high CHT Float level too high / float punctured Rich , floodingRough idle, fuel overflow Float level too low Weak Power loss, flat spots Primer left unlocked Rich at slow runningRough idle, may stop Prolonged weak mixture Weak Excessive cylinder head temperature Exhaust valve sticking open Hot gas reaches the induction and exhaust Backfiring Accelerator pump failed Weak on acceleration Flat spot or weak cut
Chapter 8 · Carburettors
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the faults that turn up in exams. A punctured or enlarged main jet lets too much fuel through: the mixture is rich, the R P M falls, the engine runs roughly and may smoke black. A partly blocked jet does the opposite: weak mixture, lower power and R P M, and high cylinder head temperature. A float level set too high, or a punctured float that sinks, gives a rich mixture and flooding; a low float level gives a weak one. A primer that has not been locked keeps feeding fuel, so the idle mixture is too rich. Prolonged use of a weak mixture is the classic cause of excessive cylinder head temperatures. An exhaust valve that sticks open lets burning gas reach both the exhaust and, at the overlap, the induction, so the engine backfires. And if the accelerator pump fails you will feel a flat spot, or a weak cut, every time you open the throttle quickly.
Summary
The float carburettor in six lines Two principles U-tube and venturi: throat depression, set by airflow, drives fuel from the float chamber.
Float, jet, throttle Float and needle hold the level; main jet sizes the flow; throttle sets airflow. Opening it raises manifold pressure.
Accuracy Balance duct equalises pressures; diffuser bleeds air to stop richening as airflow rises.
Idle and stopping Idle jet at the throttle lip; smooth change-over avoids flat spots; stop with idle cut-off.
Mixture and power Lean as you climb (needle or air bleed). Power jet or back-suction economiser: rich at power, lean in cruise.
Accelerate and start Accelerator pump prevents a weak cut; primer to the manifold; pumping the throttle risks fire.
Chapter 8 · Carburettors
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. The float carburettor rests on two principles, the U-tube and the venturi: the throat depression, set by the airflow, pushes fuel out of the float chamber. The float and needle valve hold the fuel level just below the nozzle, the main jet sizes the flow, and the throttle sets the airflow; opening it raises manifold pressure. The balance duct keeps the float chamber at intake pressure, and the diffuser bleeds in air to stop the mixture richening as airflow rises. At idle a separate jet at the throttle lip takes over, a smooth change-over avoids flat spots, and the idle cut-off stops the engine cleanly. The mixture control corrects for altitude, and the power jet or back-suction economiser gives rich mixtures at high power and lean ones in the cruise. Finally, the accelerator pump prevents a weak cut, and the primer feeds the manifold for starting.