Engines · Chapter 17
Combustion Chambers How a flame that travels at a couple of feet per second survives in a 500 foot per second gale, and delivers gas the turbine can survive.
primary · secondary · tertiary air
20 % burns · 20 % anchors the flame · 60 % cools
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to combustion chambers. Between the compressor and the turbine sits the hottest part of the engine. Air arrives from the compressor at hundreds of feet per second, yet a kerosene flame only travels at a foot or two per second, so how does the flame stay alight? And how do we burn fuel at two thousand degrees and still hand the turbine a gas it can survive? In this lesson you will learn how the chamber divides and slows its air, the three types of combustion system, how drains, stability limits and relighting work, and how the fuel spray nozzles break the fuel into a fine mist.
snout
from the
compressor
to the
turbine
1 · The task What the chamber must do, temperatures, pressures and the flame-speed problem.
2 · Dividing the air Primary, secondary and tertiary air, the toroidal vortex and the air/fuel ratio.
3 · The three systems Can, can-annular and annular chambers, interconnectors, drains and wet starts.
4 · Burning well Stability, relighting, efficiency and the fuel spray nozzles.
Chapter 17 · Combustion Chambers
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First, the task of the combustion chamber: what it has to achieve, the temperatures and pressures through it, and the basic problem that the air arrives far faster than a flame can travel. Second, how the chamber solves that problem by dividing the air into primary, secondary and tertiary streams, how the toroidal vortex holds the flame in place, and what air to fuel ratios are used. Third, the three types of combustion system, multiple cans, can-annular and annular, with their interconnectors, their drains, and what happens after a wet start. Finally, how we keep the combustion stable, how an engine is relit in flight, how efficient it all is, and how the fuel spray nozzles turn liquid fuel into a fine mist.
Part 1 · The task
What the combustion chamber must do Contain the burning mixture of compressor air and nozzle fuel Release the maximum heat at a substantially constant pressure Give the turbine a uniformly heated, expanded and accelerated gas stream Burn stably and efficiently over a wide range of conditions Use fuel efficiently and keep pollution low
What the combustion chamber must do
Burn the fuel completely
maximum heat release, little smoke
At nearly constant pressure
a small loss only, 3 to 8 %
Deliver an even, hot gas stream
uniform temperature to the turbine
Stay alight everywhere
idle to take-off, sea level to altitude
Light, and relight in flight
within the relight envelope
Be compact and durable
low weight, long life, low emissions
Chapter 17 · Combustion Chambers
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The combustion chamber sits between the compressor and the turbine. Its job is to contain the burning mixture of air, delivered by the compressor, and fuel, sprayed in by the fuel nozzles, and to release the maximum heat at a substantially constant pressure. What it hands on to the turbine must be a uniformly heated, expanded and accelerated stream of gas, with no hot spots. That is not easy. The chamber has to burn stably and efficiently from idle to take-off and from sea level to high altitude, light reliably on the ground and relight in flight, and stay compact and durable. Because fuel is expensive and the public is rightly concerned about exhaust smoke and pollution, modern designs aim to burn every drop completely. In the scene, follow the air from the compressor through the fuel spray and the burning zone to the nozzle guide vanes at the turbine entry.
Part 1 · The task
Temperature allowed and temperature required Air arrives already at about 600 °C from compression In the primary zone the gas reaches about 2,000 °C : the hottest place in the engine The NGV and turbine materials set the limit on the gas leaving the chamber So it must be cooled to about 1,000 to 1,500 °C before the turbine Any excursion above the limit risks turbine disintegration
0
500
1000
1500
2000
Gas temperature (°C), full power
15 °C
600 °C
2000 °C
1,000–1,500 °C
700 °C
intake
compressor
exit
primary
zone
turbine
entry
turbine
exit
Hottest: the primary zone, about 2,000 °C
Turbine entry limited by NGV and blade materials
so dilution air brings it down to 1,000–1,500 °C
Chapter 17 · Combustion Chambers
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at the temperatures. The air arrives from the compressor already hot, about six hundred degrees Celsius at full power on a modern engine, and fuel is added to raise it much further. In the centre of the primary zone, where the fuel actually burns, the gas reaches about two thousand degrees. That is the hottest place in the whole engine, so if a question asks where the highest temperature is found, the answer is the combustion chamber. But the gas cannot leave at that temperature. The maximum temperature allowed is set by the materials of the nozzle guide vanes and the turbine blades, and the slightest excursion above it risks the turbine disintegrating. So the gas must be cooled to somewhere between one thousand and fifteen hundred degrees before it leaves. At lower power the fuel flow and the temperatures are lower. Watch the graph in the scene: the pressure peaks first, and the temperature peaks in the combustor.
Part 1 · The task
Pressure and velocity through the chamber Highest pressure in the engine: the diffuser outlet , at the entry to the combustion chamber Burning is in theory at constant pressure In practice the pressure falls slightly : 3 to 8 % , the price of turbulence and mixing The gas temperature rises greatly, so its volume and velocity increase Through the combustion section: T up, V up, p slightly down
Through the combustion chamber
Temperature
↑↑
large rise from heat release
Velocity
↑
hot gas expands and speeds up
Pressure
↓ slightly
3 to 8 % lost to turbulence and mixing
Worked example: 35 : 1 engine at sea level
compressor exit / chamber inlet
514 psi
chamber exit (3 % loss)
499 psi
chamber exit (8 % loss)
473 psi
Highest pressure in the engine: the diffuser outlet,
at the entry to the combustion chamber
Chapter 17 · Combustion Chambers
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the pressure. The air is slowed down in the diffuser between the compressor and the combustion chamber, and slowing it raises its pressure further, so the highest pressure anywhere in the engine is found at the diffuser outlet, the entry to the combustion chamber. In theory combustion then takes place at constant pressure. In practice there is a small loss, between three and eight per cent of the entry pressure, because the chamber has to create plenty of turbulence to mix the fuel and air. On a thirty five to one engine at sea level that is a fall from about five hundred and fourteen psi to somewhere between about four hundred and seventy and five hundred psi. Meanwhile the temperature rises enormously, so the gas expands and its velocity increases. So through the combustion section the temperature and the velocity rise and the pressure falls slightly. You can see all three on the graph in the scene.
Part 1 · The task
The flame-speed problem Air leaves the compressor at up to about 500 ft/s The flame rate of kerosene is only 1 to 2 ft/s A flame exposed to that airflow would be blown out at once The diffuser slows the air first (raising its pressure), but not enough Further slowing and recirculation are needed in the primary zone
Air speed against flame speed
1
10
100
1000
speed, feet per second (log scale)
compressor exit
500 ft/s
after the diffuser
250 ft/s
primary zone, local
10 ft/s
kerosene flame
1–2 ft/s
Air from the compressor: up to about 500 ft/s
Kerosene flame speed: only 1 to 2 ft/s
about 250 times slower: an exposed flame would blow out
Fix: a diffuser to slow the air (pressure peaks here),
then snout, swirl vanes and recirculation
Chapter 17 · Combustion Chambers
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the central problem of combustion chamber design. Air enters the combustion section at roughly the speed it entered the engine, and speeds of up to five hundred feet per second are not unusual. The flame rate of kerosene, the speed at which the front of the flame travels through the fuel vapour, is only one to two feet per second. Put a kerosene flame into a five hundred foot per second airstream and it would be extinguished immediately, rather like a match in a gale. So the air must be slowed down after it leaves the compressor and before it reaches the primary zone, the region where it is mixed with fuel and burnt. The diffuser does the first part, slowing the air and raising its pressure to the highest value in the engine, but that is still nowhere near enough. Further slowing, and a pattern of recirculating flow, are needed inside the flame tube itself.
Part 2 · Dividing the air
Dividing the air: 20, 20, 60
air casing
snout
flare
secondary holes
dilution holes
corrugated joints let a cooling film in
flame
cooled gas
PRIMARY 20 %
burnt with the fuel
SECONDARY 20 %
toroidal vortex
TERTIARY (dilution) 60 %
cools the gas and the walls
from the
compressor
Chapter 17 · Combustion Chambers
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is how the chamber divides its air. Air from the compressor enters the snout at the front of the flame tube, or flows round the outside of the flame tube, in the space between the flame tube and the air casing. About twenty per cent is primary air. It passes through the snout, the swirl vanes and the perforated flare around the fuel nozzle, and it is the air that is mixed with the fuel and burnt. Another twenty per cent, the secondary air, enters through a row of holes in the flame tube, and with the primary air it forms the toroidal vortex that holds the flame. The remaining sixty per cent, the tertiary or dilution air, enters progressively further back, through more holes and through the corrugated joints in the flame tube wall, to cool the gas and the walls before the gas leaves for the turbine.
Part 2 · Dividing the air
Primary air: about 20 % About 20 % of the chamber's air: the air that is mixed with the fuel and burnt Enters through the snout , then divides through the swirl vanes and the perforated flare Swirl vanes and flare reduce its velocity They also start the recirculation that stops the flame going out Fuel and primary air burn at about 15 : 1
Front of the flame tube
snout: primary air in
swirl vanes
perforated flare
fuel
recirculation
fuel burns at
about 15 : 1
Swirl vanes and flare slow the primary air
and start it recirculating round the fuel spray
Chapter 17 · Combustion Chambers
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The primary air is about twenty per cent of the flow into the combustion chamber, and it is the air that is actually mixed with the fuel and burnt. It enters through the snout, the scoop at the front of the flame tube, and then divides, some passing through the swirl vanes around the fuel nozzle and some through the perforated flare. Both of these slow the air down. The swirl vanes also set it spinning, and that swirl starts the recirculation, the circulating, slow-moving flow that keeps the flame from being extinguished. The fuel is sprayed into the middle of this swirling air as a cone, and it burns there in roughly the chemically correct proportion of about fifteen parts of air to one of fuel. So if you are asked what the swirl vanes do, the key words are: they reduce the velocity of the primary air and start the recirculation that stabilises the flame.
Part 2 · Dividing the air
Secondary air and the toroidal vortex Air not taken by the snout flows between the flame tube and the air casing About 20 % enters as secondary air through holes in the flame tube With the swirling primary air it forms a toroidal vortex : a slow, doughnut-shaped ring The vortex stabilises and anchors the flame near the fuel nozzle Centre of the primary zone: about 2,000 °C , far too hot for the turbine
The toroidal vortex anchors the flame
secondary air jets
secondary air jets
fuel
about 2,000 °C
to dilution
slow, recirculating
"smoke ring"
Secondary jets meet the swirling primary air: a ring of
slow, recirculating gas holds the flame at the burner
and stops it being blown down the flame tube
Chapter 17 · Combustion Chambers
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The air that is not picked up by the snout flows along the outside of the flame tube, in the space between the flame tube and the air casing. About twenty per cent of the total is let into the flame tube through a row of secondary air holes. These secondary jets meet the swirling primary air and together they set up a toroidal vortex, a ring of slowly circulating gas shaped like a doughnut or a smoke ring. In this cross-section you see the ring cut through, as two loops, one above and one below the centre line. Inside that ring the gas moves slowly enough for the flame to survive, and some of the burning gas is carried back towards the fuel nozzle to light the fresh fuel. So the vortex stabilises and anchors the flame, and stops it being dragged down the flame tube. The centre of this primary zone reaches about two thousand degrees, far too hot for the turbine.
Part 2 · Dividing the air
Tertiary air: about 60 % The remaining 60 % is tertiary (dilution) air Let in progressively along the flame tube It cools the gas before the turbine and cools the walls Corrugated joints let air in as a film for a gradual temperature dropModern walls: transpiration cooling , a film between laminations
Dilution and wall cooling
cooler air outside the flame tube
hot gas inside
film of cool air
corrugated joint
Transpiration cooling: a laminated wall
air seeps between the laminations and leaves as a film
Tertiary (dilution) air: about 60 % of the total
cools the gas to what the turbine can stand
and cools the flame tube walls
Gas leaves gradually cooled, with an even temperature
Chapter 17 · Combustion Chambers
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The remaining sixty per cent of the air is the tertiary air, also called dilution air. It is let into the flame tube progressively, row by row, towards the rear. It has two jobs: to cool and dilute the hot gas down to a temperature the turbine can accept, and to cool the walls. On older chambers the flame tube was built in overlapping sections with corrugated joints, which let cooler air slip in and form a protective film along the inside of the wall, giving a gradual drop in gas temperature before it exits into the nozzle guide vanes. More modern designs use transpiration cooling, where the wall is made of several laminations and a film of air flows between them before spreading along the hot surface. Either way, the gas reaching the turbine has been cooled to an even temperature. If an exam question asks the purpose of tertiary air, the answer is to reduce the gas temperature and cool the flame tube.
Part 2 · Dividing the air
The air/fuel ratio Greatest heat release: the chemically correct (stoichiometric ) ratio, about 15 : 1 by weight Used in the primary zone No detonation or dissociation problem: continuous burning, no pressure peaks Secondary and tertiary air dilute it: overall 45 : 1 to 130 : 1 Example: 100 kg/s of air, 20 kg/s primary, 1.33 kg/s of fuel, overall 75 : 1
Air / fuel ratio by weight
15 : 1
primary zone
overall 45 : 1 to 130 : 1
example 75 : 1
0
15
45
75
100
130
kg of air per kg of fuel
Worked example (100 kg of air per second)
Primary air (20 %)
20 kg/s
Fuel burnt at 15 : 1
20 ÷ 15 = 1.33 kg/s
Overall ratio
100 ÷ 1.33 = 75 : 1
Why 15 : 1 is safe here but not in a piston engine:
burning is continuous at constant pressure, with no
pressure peaks to cause detonation or dissociation
Chapter 17 · Combustion Chambers
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
For the greatest heat release the fuel must be burnt with exactly enough air to combine with all of it, the chemically correct or stoichiometric ratio. For kerosene that is about fifteen parts of air to one of fuel, by weight, and that is the mixture burnt in the primary zone. In a piston engine running at that ratio, the pressure peaks would risk detonation and dissociation. In a gas turbine there is no such problem, because burning is continuous at a nearly constant pressure, with no pressure peaks. Once the secondary and tertiary air are added, the overall ratio becomes much weaker, between about forty five and one hundred and thirty to one. Here is a worked example. With one hundred kilograms of air per second, the primary twenty kilograms burn about one point three three kilograms of fuel, and dividing the whole hundred by that gives an overall ratio of seventy five to one.
Part 3 · The three systems
The multiple (can) system Developed from Whittle's original design; used on early axial engines and on centrifugal engines such as the Dart Eight or more chambers round the engine, behind the compressor Each chamber: a flame tube inside its own air casing Usually only two igniters ; interconnectors carry the flame to the other chambers The lit chamber's higher pressure drives flame through; flow stops when pressures equalise
Multiple (can) chambers, seen from the front
3
2
1
2
3
2
1
2
engine
igniter
igniter
Numbers: the order in which the chambers light.
Each can: flame tube + its own air casing.
Interconnectors carry the flame round the ring.
Chapter 17 · Combustion Chambers
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The first of the three systems is the multiple combustion chamber system, also called the can system. It grew out of Sir Frank Whittle's original design, was used on some early axial flow engines, and is still found on centrifugal compressor engines such as the Rolls-Royce Dart. It consists of eight or more chambers arranged round the engine behind the compressor, and each chamber is a flame tube with its own individual air casing. Most engines have only two igniters, and an engine would probably start on just one. So how do the other chambers light? Through the interconnectors, tubes that join each chamber to its neighbours. When a chamber with an igniter lights, its pressure rises above that of the next chamber, and the pressure difference drives burning gas through the interconnector to light the next one. This continues round the engine until every chamber is alight. Then the pressures equalise and the flow through the interconnectors stops.
Part 3 · The three systems
Inside one combustion chamber
interconnector
igniter plug
swirl vanes
snout
flare
secondary holes
dilution holes
corrugated joints
air casing
drain
bolted to the
compressor casing
fuel nozzle
sealing ring
into the
nozzle box
flame tube
Fixed at the front, free to grow rearwards: the sealing ring keeps it gas-tight as it expands into the nozzle box
Chapter 17 · Combustion Chambers
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is one can-type chamber with its parts named. At the front, the fuel nozzle sits inside the swirl vanes and the flare, fed through the snout. The flame tube is surrounded by its air casing, and the flame tube has its rows of secondary and dilution holes and its corrugated joints. On top you can see the igniter plug in this chamber and the stub of an interconnector leading to the next chamber, and underneath a drain. Now look at the two ends. The chamber is bolted to the compressor casing at the front, so it cannot grow forwards. When it heats up it lengthens, and at the rear a sealing ring lets it slide into the nozzle box, the part of the engine just ahead of the nozzle guide vanes, while still keeping a gas-tight seal. So: fixed at the front, free to expand at the back.
Part 3 · The three systems
Wet starts and the drain system Wet start : fuel is sprayed in but the mixture fails to ignite Unremoved fuel would give a long, hot, dangerous flame from the jet pipe on the next start Drain tubes link the lowest point of each chamber to the one belowBottom drain valve at 6 o'clock : spring-loaded open , closed by chamber gas pressure when running Blow-out cycle : motor a full start cycle with the HP cock shut and ignition off
After a wet start: drain, then blow out
drain valve,
6 o'clock
drain tubes (gold): lowest point of
each chamber to the one below
Engine stopped: open
chamber
spring lifts
valve: fuel
drains
Engine running: shut
chamber
gas pressure
holds it on
its seat
Blow-out cycle: motor on the starter for a full start
cycle, HP fuel cock shut, ignition off: the air
flow evaporates the last fuel from chambers and jet pipe
Chapter 17 · Combustion Chambers
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Sometimes an engine fails to light during a start. This is a wet start: a considerable amount of fuel has been sprayed into the chambers but has not ignited. If it is not removed, the next start will produce a very long, very hot and very dangerous jet of flame from the back of the engine. There are two ways of getting rid of it. First, the drain system. Drain tubes connect the lowest part of each chamber to the chamber below it, so the fuel runs down from the top of the engine to the bottom chamber. There it leaves through a drain valve at the six o'clock position. The valve is spring-loaded towards open, so it drains whenever the engine is stopped, and during running the gas pressure inside the chamber holds it shut. Second, the blow-out cycle: the engine is motored on the starter for a full start cycle with the HP fuel cock shut and the ignition off, and the airflow evaporates what remains.
Part 3 · The three systems
The can-annular system Also called tubo-annular or cannular A number of flame tubes inside one common air casing No individual air casings: more compact than separate cans Each flame tube has its own fuel nozzle; interconnectors still needed A step between the can system and the annular system
Can-annular (tubo-annular, cannular)
engine core
Several flame tubes in ONE common annular air casing
More compact than separate cans; still has interconnectors
Chapter 17 · Combustion Chambers
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The second system is the can-annular system, also known as the tubo-annular or cannular system. Learn all three names, because the exam uses them. The difference from the multiple can system is that the flame tubes do not each have their own air casing. Instead, a number of separate flame tubes, each with its own fuel nozzle, sit inside one common annular air casing, an inner wall and an outer wall round the engine. That makes a more compact and lighter unit than a ring of separate cans. Because the flame tubes are still separate, interconnectors are still needed to carry the flame from the chambers with igniters to the others. You can think of it as a step on the way from the can system to the annular system. So if a question describes a set of flame tubes enclosed in a common air casing, the answer is the cannular system.
Part 3 · The three systems
The annular system One single flame tube , ring-shaped, between an inner and outer air casing Only about 75 % of the length of a can-annular system of the same diameter No flame propagation problems ; less casing area , so less cooling airEfficiency so high that unburnt fuel is virtually eliminated ; CO burnt to CO2 Better pressure distribution on the turbine: a more even load
Annular: one flame tube
core
outer + inner casing, one ring-shaped flame tube
Same diameter and power:
can-annular: 100 % length
annular: 75 % length
No flame propagation problem; smaller casing area,
so less cooling air; almost no unburnt fuel;
even pressure and load on the turbine
Chapter 17 · Combustion Chambers
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The third system is the annular system, used on almost every modern engine. It has just one flame tube, shaped like a ring, contained between an inner and an outer air casing, with a ring of fuel nozzles. Developed from the other two, it has several advantages. For the same power, its length is only about seventy five per cent of a can-annular system of the same diameter, which saves weight. There are no flame propagation problems, because the single flame tube is one continuous space, so no interconnectors are needed. The air casing area is smaller, so less cooling air is required. Combustion is so efficient that unburnt fuel is virtually eliminated, and carbon monoxide is burnt to harmless carbon dioxide. And the gas reaches the turbine with a much better pressure distribution, so the turbine is loaded evenly. Remember the exam favourite: the annular system has no flame propagation problems.
Part 3 · The three systems
The three systems compared Multiple (can) Can-annular Annular Flame tubes several, each in its own casing several, in one common casing one, ring-shaped Air casing one per chamber common inner and outer common inner and outer Interconnectors yes yes none needed Length and weight longest, heaviest shorter about 75 % of can-annular, lightest Cooling air needed most less least (smallest casing area) Gas to the turbine least even better most even pressure and load Typical use early jets, Dart older airliner engines almost all modern engines
Chapter 17 · Combustion Chambers
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the three systems side by side. The multiple can system has several flame tubes, each in its own casing, joined by interconnectors; it is the longest and heaviest, needs the most cooling air, and was used on early jets and centrifugal engines like the Dart. One practical advantage of separate cans is that a single chamber can be removed on its own. The can-annular system keeps separate flame tubes but puts them in one common casing, which is shorter and lighter, but it still needs interconnectors. The annular system has one ring-shaped flame tube between common inner and outer casings. It needs no interconnectors, it is the shortest, at about three quarters of the length of a can-annular system, it has the smallest casing area and so needs the least cooling air, and it gives the turbine the most even gas pressure and load. That is why it is used on almost all modern engines.
Part 4 · Burning well
Combustion stability Normally self-supporting : ignition can go off once the engine reaches self-sustaining speed Flame-out : extinction, e.g. heavy water ingestion on take-off from a contaminated runwayWeak extinction : mixture too weak, likely when throttled back in a descent Stability = smooth burning over a wide range of air/fuel ratios and mass flows The stable band narrows as mass flow rises ; the ignition loop is narrower still
0
50
100
150
200
air mass flow (relative)
Air / fuel ratio
weak limit
rich limit
ignition loop
stable burning
blow-out
The stable band narrows as the air mass flow rises
Lighting up needs a narrower band than staying alight
Weak extinction risk: throttled back in a fast descent
(low fuel flow, high air mass flow)
Chapter 17 · Combustion Chambers
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once running, combustion is self-supporting. The ignition can be switched off as soon as the engine reaches self-sustaining speed, the speed from which it can accelerate after a start without help from the starter. But some conditions can put the flame out. That is a flame-out, the extinction of the flame, for example after swallowing large amounts of water during take-off from a contaminated runway. Another cause is a mixture that has become too weak, which is most likely when the engine is throttled back during a descent, when a low fuel flow meets a high air mass flow. That is a weak extinction. Stability means smooth burning and the ability to stay alight over a wide range of air to fuel ratios and air mass flows. Look at the loop. Between the rich and weak limits the flame is stable, but the band narrows as the mass flow increases, until the flame blows out. The smaller ignition loop inside shows that starting combustion is harder than sustaining it.
Part 4 · Burning well
Relighting in flight The relight envelope : the airspeed and altitude limits within which a relight is assured The airflow keeps the engine windmilling , so the compressor supplies air Then open the HP fuel cock and select the relight switch The relight circuit is separate from the normal start circuit After a flame-out high and fast, you may need to reduce height and speed
100
150
200
250
300
350
0
10,000
20,000
30,000
40,000
indicated airspeed (kt), notional
Altitude (ft)
RELIGHT
guaranteed
too high: thin air, weak combustion
too slow:
windmill
too slow
too fast:
flame
blown out
Windmilling keeps the compressor turning: open the
HP fuel cock and select the relight switch (its own
circuit, separate from the ground start circuit)
Outside the envelope: descend and/or change speed
Chapter 17 · Combustion Chambers
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because ignition is harder than sustained burning, an engine that flames out at high speed or high altitude may not relight until both are reduced. The relight envelope shows the range of altitude and airspeed within which a serviceable engine is guaranteed to relight. Too slow, and the engine does not windmill fast enough to supply enough air. Too fast, and the airflow through the combustion chamber blows the new flame out. Too high, and the thin air makes combustion weak and hard to start. Inside the envelope, the airflow through the engine keeps it windmilling, so the compressor already supplies air; all that is needed is to open the HP fuel cock and operate the ignition. That is done with the relight switch, which works independently of the normal ground start circuit. If you are outside the envelope, descend and adjust the speed until you are inside it.
Part 4 · Burning well
Combustion efficiency How much of the fuel's potential heat the combustor actually releases Up to 99 % at high power Still about 95 % at idle Overall air/fuel ratio: weakest at idle, about 45 : 1 at high power Credit goes largely to good atomisation by the fuel spray nozzles
idle
max
90
92
94
96
98
100
engine power: idle → take-off
Combustion efficiency (%)
40
60
80
100
120
140
AFR
95 %
99 %
overall about 130 : 1
take-off about 45 : 1
Efficiency: share of the fuel's heat actually released
Up to 99 % at high power, still about 95 % at idle
Overall mixture is weakest at idle, richest at take-off
Good atomisation by the spray nozzles is the key
Chapter 17 · Combustion Chambers
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Combustion efficiency is how much of the potential heat in the fuel the combustor actually extracts. Modern gas turbines are remarkably good at it. At high power the combustion efficiency can be as high as ninety nine per cent, and even at idle it is still around ninety five per cent. The graph also shows the overall air to fuel ratio across the operating range: very weak at idle, around one hundred and thirty to one, and much richer at take-off, around forty five to one. The engine runs across that whole range while the primary zone keeps burning close to fifteen to one. A large part of the credit for this high efficiency goes to the fuel spray nozzles, which have to break the fuel up so finely that it burns completely in the short distance available, in a fast-moving airstream. That is our final topic.
Part 4 · Fuel spray nozzles
The atomisation problem
Dribble
very low pressure
Distorted pencil
low pressure
Onion
rising pressure
Tulip
nearly there
Fully atomised
high pressure
A fixed orifice only atomises well at high pressure (about 1,500 to 2,000 psi) , but at start the engine-driven HP pump turns slowly and gives low pressure .
Chapter 17 · Combustion Chambers
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fuel spray nozzles must atomise or vaporise the fuel so that it burns completely, and they must do it in a fast airstream and in a short distance. Here is the difficulty. A simple nozzle with a fixed orifice only produces a finely atomised spray at high fuel pressure, around fifteen hundred to two thousand psi. Look at the sequence. At very low pressure the fuel just dribbles out. As the pressure rises it becomes a distorted pencil, then an onion shaped film with large drops, then a tulip that starts to break up, and only at high pressure a fully atomised cone of fine droplets. The trouble is the start. The high pressure fuel pump is driven through the high speed gearbox, and when the start is selected it is turning very slowly, so it cannot produce those high pressures. Some other method is needed to atomise the fuel at the low pressures available during a start.
Part 4 · Fuel spray nozzles
The duplex nozzle Works like an orifice of variable size A small primary orifice fed by the primary fuel line : fine spray at low pressure At low pressure a pressurising valve keeps the main line shut As the engine accelerates the pressure builds, the valve opens and the main orifice adds its flow Good atomisation from start to full power
Duplex nozzle
main gallery
primary gallery
main orifice
small primary orifice
pressurising valve
opens as fuel pressure builds
0
25
50
75
100
0
500
1000
1500
2000
fuel flow (% of maximum)
Nozzle pressure (psi)
poor atomisation
main opens
duplex
single orifice
At start: tiny flow through the small primary orifice
still has the pressure for a fine spray
Chapter 17 · Combustion Chambers
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
The duplex nozzle effectively gives an orifice of variable size. It has two orifices, a small primary orifice in the centre fed by the primary fuel line, and a larger main orifice around it fed by the main line. At low fuel pressures a pressurising valve keeps the main line closed, so all the fuel goes through the small primary orifice, which can still produce a fine spray at the low pressure available. As the engine accelerates during the start the fuel pressure builds until the pressurising valve opens, and fuel flows to the main orifice as well, supplementing the primary. Look at the graph. With a single fixed orifice, the pressure at low flows is only a few tens of psi, deep in the region of poor atomisation. With the duplex nozzle, the same small flows pass through the small orifice at hundreds of psi, and the main orifice joins in only when the flow is larger.
Part 4 · Fuel spray nozzles
Airspray and vaporising systems Airspray : a high-velocity air stream breaks up the fuelNeeds only low fuel pressure , so a light gear pump can replace a heavier plunger pump Vaporising tube : fuel sprayed from feed tubes into tubes inside the flame tube , with primary airFuel is turned through 180° and vaporised by the heat of combustion The vapour then passes into the flame tube to burn
Airspray nozzle
high-speed air
fuel
air breaks the
fuel into a mist
Low fuel pressure is enough: a light gear pump will do
Vaporising tube
fuel + primary air in
turned
180°
vapour back into the flame tube
tube heated by the flame
Fuel is vaporised, not atomised, before it burns
Chapter 17 · Combustion Chambers
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two other ways to prepare the fuel. The airspray nozzle uses a high-velocity stream of air on each side of the fuel to shear it into a fine mist. Because the air does the work, it needs only a relatively low fuel pressure, so the engine can use a gear type pump, which is much lighter than the more sophisticated plunger type pump. The vaporising system works differently: it turns the fuel into vapour rather than atomising it. Fuel is sprayed from feed tubes into vaporising tubes positioned inside the flame tube, and primary air enters with it through the feed tube opening and through holes in the flame tube entry section. The fuel and air are turned through one hundred and eighty degrees inside the tube, which is heated by the surrounding combustion, so the fuel is vaporised before it passes back into the flame tube to burn.
Summary
Combustion chambers in one page Task and temperatures Max heat at nearly constant pressure, even gas to the turbine. 600 °C in, ~2,000 °C primary zone (hottest), 1,000–1,500 °C out.
Pressure and speed Highest pressure at the diffuser outlet. Through the chamber: T ↑, V ↑, p ↓ 3–8 %. Air 500 ft/s, flame 1–2 ft/s.
Air division Primary 20 % burnt at 15 : 1 (snout, swirl vanes); secondary 20 % toroidal vortex; tertiary 60 % cools gas and walls. Overall 45–130 : 1.
Systems Can: own casings, interconnectors. Can-annular: tubes in a common casing. Annular: one tube, 75 % length, no propagation problems.
Drains and relight Drain valve at 6 o'clock, spring open, gas pressure shut; blow-out with HP cock shut, ignition off. Relight envelope: speed and height.
Burning well Stable band narrows with mass flow; weak extinction in descent. 99 % efficiency at high power, 95 % at idle. Duplex, airspray, vaporiser.
Chapter 17 · Combustion Chambers
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us summarise. The combustion chamber releases the maximum heat at nearly constant pressure and hands the turbine an even stream of gas. The air arrives at about six hundred degrees, burns at about two thousand in the primary zone, the hottest place in the engine, and leaves at one thousand to fifteen hundred. The highest pressure is at the diffuser outlet; through the chamber the temperature and velocity rise and the pressure falls three to eight per cent. Because the air is so much faster than the flame, it is divided: twenty per cent primary air burnt at fifteen to one, twenty per cent secondary air forming the toroidal vortex, and sixty per cent tertiary air for cooling. Can, can-annular and annular systems differ in their casings and flame tubes, and the annular system has no flame propagation problems. Finally, remember the drains and blow-out cycle, the stability loop, the relight envelope, and the duplex, airspray and vaporising fuel systems.