Engines · Chapter 13
Constant-speed Units, Feathering and Reverse How a governor holds the RPM you select, how a dead engine's propeller is feathered, and how blades go into beta and reverse.
engine drive blades COARSEN speeder spring pilot valve flyweights pump drain pressure oil to / from prop oil → FINE spring + counterweights → COARSE RPM lever OVERSPEED weights out · valve UP · oil drains © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to constant speed propellers. In the last lesson we saw that a fixed pitch propeller is only really efficient at one speed. Here we let the blades turn in the hub, and we hand the job of choosing their angle to a small, clever governor on the front of the engine. You will watch its flyweights fly out and fall in as the R P M tries to change, and see how oil moves the blades to put things right. Then we deal with engine failure on a twin: feathering, unfeathering and autofeather. We finish with beta range and reverse, synchronising, the effects a propeller has on the aircraft, and the engine handling questions that often appear alongside this topic.
Roadmap
Letting the blades turn in the hub 1 · Controls and actuation Power, RPM and mixture levers; single and double acting pitch change; oil conventions.
2 · The governor The CSU : on-speed, overspeed , underspeed ; the RPM lever, power, airspeed and the glide.
3 · Feathering and reverse Windmilling drag, feathering , the latch, the POCOS , the PCU, alpha and beta , reverse.
4 · Effects and handling Synchronising, propeller effects on the aircraft, and piston engine handling checks.
Chapter 13 · Constant-speed Units, Feathering and Reverse
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan. First, the controls and the hardware: the three levers on the pedestal, and how oil turns the blades in single and double acting propellers. Second, the heart of the lesson, the constant speed unit. We will watch it react to an overspeed and an underspeed, and work out what it does when you move the R P M lever, add power, speed up or glide. Third, what happens when an engine fails on a twin: why a windmilling propeller is so dangerous, how feathering and unfeathering work on both types of propeller, the centrifugal latch, the feathering pump and its pressure switch, and the propeller control unit of a turboprop with autofeather, beta range and reverse. Finally, synchronising, the four effects a propeller has on the aircraft, and the engine handling checks that complete the piston engine syllabus.
Part 1 · Controls
Three levers, two gauges Throttle (power lever, black): sets manifold pressure , read on the MAP gauge Propeller (RPM lever, blue): sets RPM , read on the tachometer Mixture (red): sets the fuel / air ratioPiston power = MAP × RPM : separate levers let you choose the best combination Forward = more: max RPM (fine pitch), full throttle , full rich in Hg MANIFOLD PRESSURE RPM × 100 TACHOMETER THROTTLE power lever PROPELLER RPM lever MIXTURE rich ↔ lean forward
Chapter 13 · Constant-speed Units, Feathering and Reverse
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
With a constant speed propeller there are three levers on the pedestal. The black throttle, now called the power lever, controls the manifold pressure, and you set it by watching the manifold pressure gauge. The blue propeller lever, or R P M lever, selects the R P M, and you set it by watching the tachometer. The red mixture lever sets the ratio of fuel to air. Why two power controls? The power of a piston engine depends on both the manifold pressure and the R P M. With separate levers you can choose the combination that gives the best efficiency, fuel economy and engine life for each phase of flight. In every case, forward means more: R P M lever forward is maximum R P M, which is fine pitch; throttle forward is full power; mixture forward is full rich. So the classic exam question has the answer: power lever by the manifold pressure gauge, R P M lever by the tachometer.
Part 1 · Actuation
Oil turns the blades: single and double acting Pitch change is almost always hydraulic , using engine oil boosted by a pump in the CSU (about 120–200 psi ) Single acting : oil on one side of the piston, usually towards fine Its spring and centrifugal counterweights drive the blades coarse , and to feather when the engine stops Double acting : a sealed piston with fine oil on one side and coarse oil on the otherA link turns the blades through an offset pin on each blade butt Single acting oil one side only: oil → FINE; spring + counterweights → COARSE / feather oil spring fine-pitch oil blade butt offset pin counterweight Double acting oil both sides: fine oil and coarse oil; no spring needed fine oil coarse oil fine side coarse side blade butt offset pin
Chapter 13 · Constant-speed Units, Feathering and Reverse
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
How do the blades actually turn? Electric pitch change exists but is rare; almost all propellers use oil. The source is the engine's own lubricating oil, boosted by a small pump in the constant speed unit to around one hundred and twenty to two hundred p s i. In a single acting propeller, a piston in a cylinder on the front of the hub has oil on one side only. Usually that oil pushes the piston to move the blades towards fine pitch. The return to coarse comes from a spring, or from centrifugal counterweights on the blade roots, and most have both. The spring has a second job: when the engine stops and the counterweights lose their effect, it drives the blades to feather. In a double acting propeller the piston is sealed, with fine pitch oil on one side and coarse pitch oil on the other, so no spring or counterweight is needed. Either way, a link moves an offset pin on the butt of each blade.
Part 1 · Actuation
What the CSU does with the oil Every constant speed unit has just three modes. Only the plumbing differs.
Need Single acting (oil → fine) Double acting Result RPM too low (underspeed) Send oil to the fine side Oil to fine side, coarse side to drain Blades fine off, RPM rises RPM correct (on speed) Oil shut off : hydraulic lock Both lines shut off Pitch held, RPM steady RPM too high (overspeed) Drain fine-pitch oil to scavengeOil to coarse side, fine side to drain Blades coarsen, RPM falls Feather Drain all oil; spring and counterweights → feather stop Feathering pump oil to the coarse side Blades edge-on, prop stops
On most single-engine propellers the convention is reversed: oil pressure coarsens, and the twisting moment and a spring fine the blades.
Chapter 13 · Constant-speed Units, Feathering and Reverse
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Whatever the design, the constant speed unit only ever does three things with the oil. If the R P M is too low, it supplies oil to move the blades to a finer angle, so the R P M rises. If the R P M is correct, it shuts the oil in, a hydraulic lock, so the blade angle is held and the R P M stays steady. If the R P M is too high, it moves the blades coarser. On a single acting propeller with oil to fine, that means letting the fine pitch oil drain away so the spring and counterweights can coarsen the blades. On a double acting propeller it sends oil to the coarse side while the fine side drains. Feathering is just the extreme coarse case. One caution, written under the table: most single-engine propellers work the other way round, with oil pressure increasing the pitch. The next slide compares the two.
Part 1 · Two conventions
Single-engine versus feathering twin Single-engine propeller: oil → coarse ; the CTM and a spring move it fineLoss of oil: blades go fine , RPM high; you keep power but may overspeed Feathering twin propeller: oil → fine ; spring and counterweights move it coarseLoss of oil: blades go coarse towards feather , the safe failure for a twin Scene: oil = coarse (single-engine) in an overspeed : oil flows to the piston Single-engine propeller oil pressure → COARSE CTM + spring → FINE Oil pressure lost: blades go FINE, RPM high full power kept; may overspeed Feathering twin propeller oil pressure → FINE spring + counterweights → COARSE Oil pressure lost: blades go COARSE towards FEATHER: safe on a twin Same governor logic: only the supply and drain ports are swapped.
Chapter 13 · Constant-speed Units, Feathering and Reverse
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two oil conventions, and it matters which one an aircraft uses. On most single-engine aircraft, oil pressure drives the blades coarse, while the centrifugal twisting moment and a spring drive them fine. If oil pressure is lost, the blades go to fine pitch and high R P M. That is the safer failure for a single: you keep full power to reach a field, although you may have to throttle back to avoid an overspeed. The model shows this convention. Watch an overspeed: the flyweights fly out, the pilot valve lifts, and oil flows to the piston to coarsen the blades until the R P M is correct again. On a feathering twin, oil drives the blades fine, and the spring and counterweights drive them coarse. Lose the oil, and the propeller goes towards feather, the safe failure on a twin with a dead engine. The governor logic is identical; only the ports are swapped.
Part 2 · The governor
Inside the constant speed unit Engine driven from the front of the engine; the same shaft drives the booster pump L-shaped flyweights on the rotating head: their toes lift the pilot valve The speeder spring pushes the valve down; its load is set by the RPM lever through a rack and pinion On speed : flyweight force = spring force; the valve land covers the port ; oil is trappedFrom here on: feathering-twin convention, oil = fine engine drive pitch held speeder spring pilot valve flyweights pump drain pressure oil to / from prop oil → FINE spring + counterweights → COARSE RPM lever ON SPEED weights upright · port covered · oil trapped
Chapter 13 · Constant-speed Units, Feathering and Reverse
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the governor itself. It is driven by the engine, usually from a gear at the front just behind the propeller, so it senses every change in engine R P M. The same drive turns a small booster pump that raises the oil pressure. On the rotating head sit L shaped flyweights. As they spin, centrifugal force tries to throw them outwards, and their toes push up on the pilot valve. On top of the valve sits the speeder spring, pushing it down. The pilot sets the load on that spring with the R P M lever, through a rack and pinion. When the engine is on speed, the upward force of the flyweights exactly balances the downward force of the spring. The valve sits centred, its land covers the port to the propeller, and the oil in the pitch change cylinder is trapped, so the blades hold their angle. From now on we use the feathering twin convention, oil to fine.
Part 2 · The governor
Overspeed: weights out, blades coarser Engine torque > propeller torque: RPM starts to rise Flyweight force grows: the weights fly out and lift the pilot valve The propeller port opens to drain : spring and counterweights drive the blades coarse Coarser blade → larger α → more propeller torque → RPM falls back As RPM returns, the weights come back upright and the port closes: on speed again engine drive blades COARSEN speeder spring pilot valve flyweights pump drain pressure oil to / from prop oil → FINE spring + counterweights → COARSE RPM lever OVERSPEED weights out · valve UP · oil drains
Chapter 13 · Constant-speed Units, Feathering and Reverse
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now suppose the engine torque becomes greater than the propeller torque, perhaps because you have added power or the aircraft has started to descend and speed up. The R P M starts to rise. Watch the model. The flyweights spin faster, their force overcomes the spring, and they fly outwards, lifting the pilot valve. With the feathering twin convention, lifting the valve connects the propeller line to drain, so the oil leaves the pitch change cylinder and the spring and counterweights move the blades to a coarser angle. A coarser blade meets the air at a larger angle of attack, so it makes more thrust and more propeller torque, and that extra torque slows the engine back down. As the R P M returns to the selected value, the flyweight force falls back into balance with the spring, the weights come back upright, the valve closes the port, and the governor is on speed again, with the blades at a new, coarser angle.
Part 2 · The governor
Underspeed: weights in, blades finer Propeller torque > engine torque: RPM starts to fall Flyweight force falls: the spring pushes the weights in and the valve down Pressure oil flows to the piston: the blades move fine Finer blade → smaller α → less propeller torque → RPM rises again Valve movements are tiny, so RPM changes are smooth and progressive engine drive blades FINE OFF speeder spring pilot valve flyweights pump drain pressure oil to / from prop oil → FINE spring + counterweights → COARSE RPM lever UNDERSPEED weights in · valve DOWN · oil to FINE
Chapter 13 · Constant-speed Units, Feathering and Reverse
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The underspeed is the mirror image. Now the propeller torque is greater than the engine torque, perhaps because you have reduced power or raised the nose into a climb, and the R P M starts to fall. The flyweights slow, their force drops below the spring force, and the spring pushes them inwards and drives the pilot valve down. That uncovers the port to the pressure side, so oil from the booster pump flows to the pitch change piston and moves the blades to a finer angle. A finer blade meets the air at a smaller angle of attack, so the propeller torque falls, the engine torque wins, and the R P M rises again. As it does, the flyweights come back upright, the valve closes the port, and the governor is on speed once more. In practice the valve movements are tiny and continuous, so the R P M is held smoothly, without any hunting that you would notice.
Part 2 · The RPM lever
Moving the RPM lever: the governor follows Lever forward (A → B) : rack down, speeder spring compressed Spring wins: weights pushed in , valve down , as in an underspeed Blades fine off , so the RPM increases ; then the weights move back out to upright Lever back : spring load reduced, weights move out , blades coarsen , RPM decreases The power lever stays where it is: the RPM changes without touching the throttle engine drive blades FINE OFF speeder spring pilot valve flyweights pump drain pressure oil to / from prop oil → FINE spring + counterweights → COARSE A B RPM lever A → B: forward LEVER A → B weights in · valve DOWN · oil to FINE
Chapter 13 · Constant-speed Units, Feathering and Reverse
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does the pilot choose a new R P M? Look at the lever in the corner. Pushing the R P M lever forward, from A to B, turns the pinion so the rack pushes down and compresses the speeder spring. The flyweights have not changed speed yet, so the spring now wins: it pushes the weights inwards and drives the pilot valve down, exactly as in an underspeed. Oil flows to fine pitch, the blades fine off, the propeller torque falls and the R P M increases. As the R P M rises, the flyweight force grows until it balances the new, stronger spring, and the weights move back out to upright, now at a higher R P M. Pulling the lever back does the opposite: less spring load, the weights fly out, the blades coarsen and the R P M decreases. So, to increase R P M without moving the power lever: lever forward, weights move in, blade angle decreases.
Part 2 · Governing
How the governor answers every change Within the governing range the CSU keeps RPM constant by changing the blade angle , so the blade angle of attack stays about the same.
Change (RPM lever fixed) First tendency Flyweights Blade angle Ends with Power (throttle) increased RPM rises out, then back upright increases same RPM, more thrust Power reduced RPM falls in, then upright decreases same RPM, less thrust TAS / IAS increased (descend) RPM rises out, then upright increases same RPM, same α TAS reduced (climb) RPM falls in, then upright decreases same RPM, same α RPM lever forward spring wins in, then out decreases higher RPMRPM lever back weights win out, then in increases lower RPM
Exam sequence for a power increase: weights move out , blade angle increases , RPM decreases back to the selection, weights move in to upright.
Chapter 13 · Constant-speed Units, Feathering and Reverse
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table pulls the governor's behaviour together. Keep the R P M lever fixed and add power: the R P M tends to rise, the weights fly out, the blade angle increases, the R P M comes back down, and the weights return upright. The result is the same R P M with more thrust. Reduce power and the opposite happens. Now change the airspeed. Speed up, for example in a descent, and the angle of attack tries to fall, so the R P M tends to rise and the governor increases the blade angle. Slow down in a climb and it decreases the blade angle. In both cases the angle of attack ends up about the same. Moving the lever itself changes the target: forward gives a finer blade and a higher R P M, back gives a coarser blade and a lower R P M. Learn the sequence in the caption word for word; it is a favourite exam question.
Part 2 · Governing range
Constant speed in action, and its limits As TAS rises at constant RPM the CSU increases the blade angle ; α and RPM stay constant Governing only works between the fine and coarse pitch stops On a stop the propeller acts like a fixed pitch one: e.g. low power on the approach, RPM falls below the selection Result: near-optimum efficiency over a wide speed range; more efficient than a fixed pitch propeller Scene: take-off at 2 400 RPM ; the blades coarsen as the aircraft accelerates 0 40 80 120 160 200 0° 10° 20° 30° 40° 50° TAS (kt), RPM held at 2 400 blade angle at 75% R fine pitch stop coarse pitch stop blade angle increases with TAS (α and RPM stay constant) on the fine stop Governing range: between the fine and coarse pitch stops On a stop the propeller behaves like a fixed pitch propeller: e.g. low power on the approach → RPM falls below the selection
Chapter 13 · Constant-speed Units, Feathering and Reverse
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us watch the governor through a take-off at two thousand four hundred R P M. At low speed the blades sit on the fine pitch stop. As the aircraft accelerates, the angle of attack starts to fall, the propeller torque drops and the R P M tries to rise. The governor responds and coarsens the blades, restoring the angle of attack. As the aircraft goes faster still, it does so again. So with a constant speed propeller, blade angle increases with true airspeed, while the angle of attack and the R P M stay constant. The graph shows the limit. The governor can only work between the fine and coarse pitch stops. If the blade angle it needs lies outside them, the blades sit on the stop and the propeller behaves like a fixed pitch propeller. The common case is low power on the approach: the blades reach the fine stop and the R P M falls below the selected value.
Part 2 · The glide
The RPM lever in a glide Throttle closed: the propeller is windmilling and making drag RPM lever forward : finer pitch, higher RPM, more drag : steeper descent, less range , lower L/D RPM lever back : coarser pitch, lower RPM, less drag : shallower descent, more range , higher L/D Pitch decreased in a glide: rate of descent up , L/D down Pitch increased : RPM down , range up Gliding at 90 kt, throttle closed, propeller windmilling RPM lever FORWARD β 8°, 2 400 RPM fine pitch, high RPM α about −6.5° MORE windmilling drag steeper glide, less range lower L/D RPM lever BACK β 16°, 2 000 RPM coarser pitch, lower RPM α about −1° LESS windmilling drag flatter glide, more range higher L/D
Chapter 13 · Constant-speed Units, Feathering and Reverse
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The R P M lever has a big effect in a glide. With the throttle closed, the engine gives little or no power and the propeller is windmilling, driven by the airflow and making drag. Look at the two blade sections, both at ninety knots. With the lever forward, the governor holds a fine pitch and a high R P M. The blade meets the air at about minus six and a half degrees, extracting a lot of energy from the airflow, so drag is high: the rate of descent increases and the range and lift to drag ratio fall. Pull the lever back and the blades coarsen, the R P M drops, and the angle of attack is only about minus one degree. Drag falls, the glide flattens and the range increases. So, in a glide, decreasing pitch increases the rate of descent and reduces the lift to drag ratio, while increasing pitch reduces the R P M and increases the range.
Part 2 · Handling the levers
The safe order for power changes INCREASE power 1 · MIXTURE rich 2 · RPM up 3 · MAP (throttle) up keeps RPM high whenever MAP is high avoids high cylinder pressure at low RPM (detonation, stress) DECREASE power 1 · MAP (throttle) down 2 · RPM down 3 · MIXTURE as required MAP comes down before RPM does avoids high cylinder pressure at low RPM (detonation, stress) Why this order High MAP with low RPM means high cylinder pressures: detonation and over-stress. So RPM must be up before MAP goes up.
Take-off RPM lever fully forward (max RPM, fine), throttle fully forward , mixture fully rich .
Cruise Reduce MAP first, then RPM , then lean the mixture as the manual allows.
Chapter 13 · Constant-speed Units, Feathering and Reverse
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because a constant speed propeller gives you two power controls, the order in which you move them matters. The rule is: never have a high manifold pressure with a low R P M. That combination produces very high cylinder pressures, which can lead to detonation and over-stress the engine. So to increase power, you go from right to left on the pedestal: mixture rich first, then R P M up, then manifold pressure up with the throttle. To decrease power, you reverse it: throttle back first to reduce the manifold pressure, then bring the R P M back, then set the mixture. For take-off everything goes fully forward: R P M lever forward for maximum R P M and fine pitch, throttle forward for full power, and mixture fully rich. In the cruise, reduce the manifold pressure, then the R P M, then lean the mixture as the flight manual allows.
Part 3 · Engine failure
Why a dead engine's propeller is feathered Engine fails: the CSU senses the RPM drop and drives the blades to fine , trying to hold RPM Result: windmilling on the fine stop: huge drag, violent yaw towards the dead engine; the engine may be damaged Feathering : blades turned edge-on (about 85–90°): no torque, the propeller stops Drag: windmilling (fine) > stopped > feathered Unfeathering is mainly for training : practising asymmetric flight Drag of a failed engine's propeller (illustrative) Windmilling, fine pitch, high RPM greatest: extracts energy from the airflow Stopped, not feathered a flat plate of blades across the flow Feathered (about 90°) least: blades edge-on, no torque, prop stops Windmilling drag > stationary drag > feathered drag
Chapter 13 · Constant-speed Units, Feathering and Reverse
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
When an engine fails on a twin, its governor does exactly what it was designed to do. It senses the R P M falling and drives the blades towards fine pitch, trying to keep the R P M up. The propeller ends up windmilling on the fine pitch stop, driven by the airflow. That gives a very large drag on one side, and a violent yaw towards the dead engine. And if the engine is mechanically damaged, being turned by the propeller can make it break up or catch fire. The cure is feathering. Watch the blades turn to about eighty seven degrees, edge-on to the airflow. They make no torque, so the propeller stops, and the drag falls to a minimum. Remember the order: drag is greatest when windmilling at fine pitch and high R P M, less when simply stopped, and least when feathered. There is rarely a need to unfeather a failed engine; the facility exists mainly for training.
Part 3 · Single acting
Feathering and unfeathering a single acting propeller Feather : RPM lever fully back, then through the gate into FEATHERThe rack rises fully, unloading the spring; the CSU lifts the pilot valve (mechanically if the engine has stopped) Fine-pitch oil drains ; counterweights (engine turning) or the spring (stopped) drive the piston to the feather stop Unfeather : lever to match the live engine, then the unfeather button releases oil stored in an accumulator Once windmilling starts: fuel and ignition to restart; lever not at max RPM, to avoid a yaw swing Single acting: feathering and unfeathering max RPM min RPM FEATHER RPM lever through the feather gate CSU valve lifted gas accumulator solenoid valve UNFEATHER button spring + counterweights push to the feather stop FEATHER 1 lever to feather 2 valve lifted 3 fine oil drains 4 → feather stop UNFEATHER: lever level with the live engine Unfeather: button opens the solenoid; stored oil drives the blades off the feather stop towards fine
Chapter 13 · Constant-speed Units, Feathering and Reverse
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
To feather a single acting propeller, you bring the R P M lever fully back, and then through a gate, a dog-leg or a push-in detent, into the feather position. That lifts the rack all the way, removing the load on the speeder spring, so the governor sees a huge overspeed and lifts the pilot valve fully. If the engine has stopped, the flyweights have no force, so the feather selection lifts the valve mechanically. All the fine pitch oil drains away, and the counterweights, if the engine is still turning, or the spring if it is not, push the piston onto the feather stop. To unfeather, you first put the lever level with the live engine's lever, which loads the spring and sets the valve to send oil to fine. Then you press the unfeather button. A solenoid valve releases oil stored under pressure in an accumulator, which drives the blades off the feather stop. The airflow starts the propeller windmilling, and fuel and ignition restart the engine.
Part 3 · Single acting
The centrifugal latch After shut-down, trapped fine oil leaks away and the spring would feather the propeller overnight Starting a piston engine with feathered blades would overload the starter Centrifugal latches engage below about 700 RPM : they stop the piston after about 5° of travelOn start, oil pushes the piston back to fine; the latch releases above 700 RPM (warm-up 1 100–1 200) A failing engine must be feathered before its RPM falls below the latch speed Centrifugal latch (piston engine, single acting) Running: above ~700 RPM latch held OUT by centrifugal force latch thrown out latch pin on piston fine pitch Stopped / below ~700 RPM latch springs IN: blocks feathering latch engaged latch pin on piston held ~5° from fine spring pushes towards feather Stops the springs feathering a parked engine (starter load). Feather a failing engine BEFORE its RPM falls below the latch speed.
Chapter 13 · Constant-speed Units, Feathering and Reverse
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
A single acting propeller has a problem on the ground. When a piston engine is shut down, its propeller is in fully fine pitch, held there by oil trapped on the fine side of the piston, against the feathering spring. Over the next few hours that oil leaks away through the clearances in the pilot valve, and the spring would slowly push the blades all the way to feather. On a piston engine, starting against feathered blades would overload the starter. So centrifugal latches are fitted. With the engine running they are held out. Below about seven hundred R P M they spring in, and after about five degrees of travel they catch latch pins on the back of the piston, stopping it short of feather. On start-up, oil pressure drives the piston back to the fine stop and the latches release as the R P M passes seven hundred. The catch: you must feather a failing engine before its R P M falls below the latch speed.
Part 3 · Double acting
Feathering pump, hold-in button and POCOS No springs or counterweights: feathering must be hydraulic , so a protected oil reserve is kept in the tank RPM lever to feather lifts the valve; the feather button is held in by a coil and runs an electric feathering pump Oil goes to the coarse side; at the feather stop the pressure rises and the POCOS releases the button: pump stops Unfeather : lever beside the live engine's, press the button to run the pump; pull it out once windmilling startsAn engine free to rotate will unfeather itself by windmilling once the blades move a few degrees Double acting: feathering pump and POCOS oil tank engine oil reserve feathering reserve (below the standpipe) M electric feathering pump CSU coarse side filled → FEATHER stop P POCOS pressure switch FEATHER button (held in by a coil) 1 RPM lever to feather 2 press FEATHER: pump runs 3 piston hits feather stop 4 pressure rises: POCOS breaks the hold-in coil
Chapter 13 · Constant-speed Units, Feathering and Reverse
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
A double acting propeller has no spring and no counterweights, so every movement, including feathering, must be done with oil. The oil tank keeps a protected reserve below a standpipe, so even if the engine has lost its normal oil, there is oil for feathering. You move the R P M lever back through the gate to feather, which lifts the pilot valve to send oil to coarse and drain the fine side. Then you press the feather button. A coil holds it in and energises an electric feathering pump. Oil drives the piston onto the feather stop, the pressure then rises, and a pressure operated cut-off switch, the POCOS, breaks the hold-in circuit. The button pops out and the pump stops. To unfeather, you place the lever beside the other engine's lever, so the valve now directs oil to fine, and press the button again. As soon as the propeller starts to windmill, you pull the button out to stop the pump; the windmilling does the rest.
Part 3 · Turboprops
The propeller control unit and autofeather single power lever PCU: blade angle / RPM FCU: fuel flow RPM and fuel change together: the propeller and the compressor / turbine accelerate in step without over-stressing the hot end Piston diesels with FADEC use the same single-lever idea Mechanical feathering lever Lifts the PCU valve into the feather position when the engine's HP cock is closed in flight.
Autofeather Senses low torque with high power selected: a valve lift solenoid and the feathering pump feather the propeller, leaving the pilot free to fly.
Pitch lock solenoid Sends oil to the pitch lock to go from flight fine to ground fine or open the way to reverse .
Chapter 13 · Constant-speed Units, Feathering and Reverse
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a turboprop the governor is called the propeller control unit, or P C U. It works like a constant speed unit, but it is often linked to a single power lever that also drives the engine's fuel control unit, so the propeller R P M and the fuel flow change together. That lets the heavy propeller and the compressor and turbine accelerate in step, quickly, without over-stressing the hot end. Modern diesel piston engines use the same single lever idea under a FADEC. The P C U carries extra parts. A mechanical feathering lever lifts the valve to feather when the engine's H P cock is closed. Autofeather watches the torque meter: if the torque is low while high power is selected, as in an engine failure on take-off, a valve lift solenoid and the feathering pump feather the propeller automatically, so the pilot can concentrate on flying. And a pitch lock solenoid lets oil reach the pitch lock to select ground fine or reverse.
Part 3 · Alpha and beta
Alpha range and beta range full reverse zero blade angle ground fine flight fine stop feather ALPHA range: flight fine stop → feather in flight · governed by the CSU / PCU (automatic, constant speed) BETA range: flight fine → reverse ground only · power lever sets blade angle blade angle → positions are illustrative FINER COARSER Alpha : feather to flight fine, the governed flight range. Beta : flight fine to reverse, ground only, the pilot controls blade angle directly.
Chapter 13 · Constant-speed Units, Feathering and Reverse
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many turboprop propellers can move through a very wide range of blade angles, from feathered, the coarsest possible, all the way to reverse, the finest. The range is split in two at the flight fine pitch stop. The alpha range runs from feather down to flight fine. It is used in flight, on the take-off run and early in the landing roll, and in it the propeller control unit governs automatically, as a constant speed propeller. The beta range runs from flight fine down through ground fine and into reverse. It is only ever used on the ground, after the flight fine stop has been withdrawn. In the beta range the governor no longer chooses the blade angle; the pilot sets it directly with the power lever. So remember: alpha is the automatic, governed range in flight, and beta is the manual range on the ground.
Part 3 · Beta and reverse
Ground fine and reverse pitch On the landing roll the flight fine stop is withdrawn ; weight-on-wheels switches stop this in flight Ground fine : a much finer angle, giving strong aerodynamic braking ; the stop re-engages as TAS rises on take-offReverse : power lever back through the gate; RPM lever at max ; more power gives more negative pitchSpeeder spring pushed down (simulated underspeed ); a follow-up cam centres the valve at the chosen angle In reverse the angle of attack is greatest at the blade tips full reverse zero blade angle ground fine flight fine stop feather ALPHA range: flight fine stop → feather in flight · governed by the CSU / PCU (automatic, constant speed) BETA range: flight fine → reverse ground only · power lever sets blade angle blade angle → positions are illustrative FINER COARSER
Chapter 13 · Constant-speed Units, Feathering and Reverse
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
On touchdown, the pilot withdraws the flight fine pitch stop, usually with a lever or by moving the power lever through a gate. Weight-on-wheels switches make sure this can only happen on the ground, and lights confirm that every propeller has made the change. The blades first go to ground fine, a much finer angle that gives strong aerodynamic braking; on the next take-off run, the stop re-engages automatically as speed builds. Many propellers go further, into reverse. With the R P M lever left at maximum, the pilot moves the power lever back into the reverse range, and the more power is added, the more negative the blade angle becomes. The speeder spring is pushed down to simulate an underspeed, sending oil to fine, and a follow-up cam on the blade root re-centres the valve when the chosen angle is reached. Because of the twist, the tips end up with the most negative angle, so in reverse the angle of attack is greatest at the tips.
Part 4 · Multi-engine
Synchronising and synchrophasing Small RPM differences cause a tiring beat noise and vibration Synchroniser : compares each slave with the master engine and drives a torque motor to reset the slave's speeder springNo difference, no output: slaves hold the master's RPM Synchroscope : a small propeller that turns only when a slave propeller's RPM differs from the master'sSynchrophasing : same RPM, blades held a chosen angle apart to cut noise furtherSynchronising: slaves follow the master MASTER engine governor RPM signal SLAVE engine governor RPM signal synchroniser compares RPM torque motor resets the slave's speeder spring synchroscope turns only if the slave differs from the master Synchrophasing same RPM, blades set a chosen angle apart: quieter cabin
Chapter 13 · Constant-speed Units, Feathering and Reverse
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a multi-engine aircraft, even a small difference in R P M between propellers produces a slow, throbbing beat that is very tiring for crew and passengers. A synchronising system removes it. One engine is the master. Its governor sends an R P M signal to a control unit, which also receives signals from the other, slave, engines. If a slave is turning faster or slower than the master, the control unit sends a current to a small torque motor on that slave's governor, turning it one way or the other to reset the speeder spring until the R P M matches. When there is no difference there is no output. Many aircraft show this on a synchroscope, a little propeller that only rotates when a slave propeller is out of step with the master. Synchrophasing goes one step further: with the R P M already matched, it holds the blades of neighbouring propellers at a chosen angle apart, making the cabin quieter still.
Part 4 · Propeller effects
What the propeller does to the aircraft Torque reaction roll LEFT Spiral slipstream yaw LEFT Gyroscopic precession pitch up → yaw RIGHT Asymmetric blade effect high α → yaw LEFT prop clockwise (from behind) aircraft rolls the other way hits left of fin nose left cure: offset fin (or rudder trim) pitch up: force at the TOP 90° on in the direction of rotation felt at the RIGHT side effect grows with RPM and with the rate of pitch or yaw down-going blade: more α, more thrust up-going: less seen from behind, nose high All for a right-hand propeller (clockwise seen from behind); a left-hand propeller reverses every effect.
Chapter 13 · Constant-speed Units, Feathering and Reverse
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
A propeller also pushes the aircraft around in ways the pilot must correct. Take a right-hand propeller, turning clockwise seen from behind. First, torque reaction: the engine turns the propeller clockwise, so the propeller turns the aircraft the other way, rolling it to the left. Second, the slipstream spirals back round the fuselage in the same clockwise direction and strikes the left side of the fin, pushing the tail right and yawing the nose left; designers often offset the fin slightly to cancel this. Third, gyroscopic precession: the spinning propeller is a gyroscope, so a force applied to it takes effect ninety degrees later in the direction of rotation. Pitch the nose up, and the aircraft yaws right. The effect grows with R P M and with the rate of pitch or yaw. Fourth, the asymmetric blade effect: at a high angle of attack the down-going blade, on the right, takes a bigger bite and makes more thrust, yawing the aircraft left.
Part 4 · Handling
Piston engine handling: start and ground checks Item What to know Before start Park nose into wind . Inverted inline and radial engines: with the ignition OFF, check for hydraulicing (oil in the lower cylinders). Static boost Note the MAP gauge before start : it reads the ambient pressure. Start The key springs back to BOTH . First check: oil pressure . Fire in the induction on start Keep cranking on the starter and select idle cut-off : the fire is drawn through the engine. Dead cut check At ground warm-up RPM : both magnetos briefly off, to prove the switches work. Mag drop check Engine cuts on one magneto: stop the engine . No drop : a switch stuck open circuit (that magneto is live). Reference RPM Set when the engine is first installed , as the yardstick for later power checks. Propeller exercise After warm-up, cycle fine ↔ coarse to replace cold oil and check RPM control; check feathering where fitted.
Chapter 13 · Constant-speed Units, Feathering and Reverse
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
The exam also asks about general piston engine handling, so here is the ground part. Park nose into wind. On an inverted inline or radial engine, oil can drain into the lower cylinders, so with the ignition off you check for hydraulicing before starting. Static boost, the manifold pressure reading before start, simply shows the outside air pressure. When the engine starts, the key springs back to both, and the first check is oil pressure. If over-priming causes a fire in the induction, keep the engine turning on the starter and select idle cut-off, so the fire is drawn through the engine. The dead cut check is done at ground warm-up R P M. If the engine cuts on one magneto during the mag drop check, stop it. No drop at all suggests a switch stuck open circuit, leaving that magneto live. Reference R P M is established when the engine is first installed. Finally, exercise the propeller to purge cold oil and prove R P M control.
Part 4 · Handling
Piston engine handling: in flight and shut-down Situation What to know Take-off Mixture fully rich , carburettor heat off , RPM lever and throttle fully forward. Climb Watch the temperatures: high power at low airspeed lets them creep up. Weak mixture Prolonged: overheating . At high power: detonation . Excessively rich mixture Loss of power and a drop in cylinder head temperature.Carb ice, fixed pitch, cruise RPM decreases , airspeed falls, altitude is lost.Low-power, high-speed descent Risk of over-cooling and carburettor icing . After landing Correct running-down procedure prevents spark plug fouling . Shut-down Mixture to idle cut-off , then magnetos off.
Chapter 13 · Constant-speed Units, Feathering and Reverse
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
And here is handling in flight. Take off with the mixture fully rich, so the extra fuel cools the cylinders, and with the carburettor heat off, so you have full power, with the R P M lever and throttle fully forward. In the climb you are at high power and low airspeed, so watch the temperatures, which can creep up. A weak mixture run for a long time makes the engine overheat, and at high power it brings the danger of detonation. An excessively rich mixture loses power and lowers the cylinder head temperature. With a fixed pitch propeller in the cruise, carburettor ice shows itself as a falling R P M, a loss of airspeed and a loss of height. A long, low power descent at high speed risks over-cooling the engine and carburettor icing. After landing, the correct running-down procedure stops the spark plugs fouling. And the correct way to shut down is to move the mixture to idle cut-off, then switch off the magnetos.
Summary
Constant speed and feathering: what to take into the exam Levers Throttle → MAP ; RPM lever → tachometer . Up: mixture, RPM, MAP. Down: MAP, RPM.
On speed Flyweight force = speeder spring force ; port covered; oil trapped.
Overspeed Weights out , valve up, blades coarsen , RPM back, weights in.
Underspeed / lever fwd Weights in , valve down, blades fine off , RPM up.
Changes Power ↑ or TAS ↑ → blade angle ↑. Glide: lever back = less drag, more range.
Feathering Drag: windmilling > stopped > feathered. Latch ~700 RPM. Accumulator / pump to unfeather . POCOS stops the pump.
Alpha / beta Alpha: feather ↔ flight fine, governed. Beta: flight fine ↔ reverse, ground, manual. Autofeather: low torque .
Effects (RH prop) Torque: roll left. Slipstream: yaw left (offset fin). Pitch up: yaw right. High α: yaw left.
Chapter 13 · Constant-speed Units, Feathering and Reverse
26
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. The throttle sets manifold pressure and the R P M lever sets the R P M on the tachometer; to increase power go mixture, R P M, then manifold pressure, and reverse that to reduce it. On speed, the flyweight force balances the speeder spring and the oil is trapped. In an overspeed the weights fly out, the blades coarsen, the R P M comes back and the weights return upright; underspeed, or pushing the lever forward, does the opposite. More power or more airspeed means a bigger blade angle, and in a glide, lever back means less drag and more range. Windmilling gives the most drag and feathering the least; a centrifugal latch stops a parked engine feathering; the POCOS stops the feathering pump. Alpha is the governed flight range, beta the manual ground range, and autofeather senses low torque. Finally, a right-hand propeller rolls the aircraft left, yaws it left with its slipstream, and yaws it right when you pitch up.