Engines · Chapter 4
Piston Engine Cooling Why an engine must be kept neither too hot nor too cold, how liquid and air cooling work, and how the pilot manages temperature with airspeed, cowl flaps, mixture and the CHT gauge.
cool air in
finned cylinder
heat out
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter four is about cooling. A piston engine turns less than a third of its fuel into useful work, and a large part of the rest soaks into the cylinders, pistons and oil. That heat has to go somewhere, or the engine knocks, its oil breaks down and parts crack. Run it too cold, though, and it wastes power. In this lesson we look at why cooling matters, how liquid and air cooling work, what fins, baffles and cowl flaps do, how the cylinder head temperature gauge works, and how you, the pilot, keep the engine in its comfortable working range from start-up to shut-down.
Roadmap
Keeping the engine in its working range
Ground: slipstream only
Take-off and climb:
high power, low speed: HOT
Cruise: cowl flaps partly closed
Descent: low power, high speed:
risk of OVERCOOLING
Shut-down
One engine, many conditions: the cooling system and the pilot keep it in its working window
1 · Why cool? Where the fuel’s heat goes, and what happens if the engine runs too hot or too cold.
2 · Liquid or air Water-glycol jackets and a radiator, or fins in the slipstream: how each works and why light aircraft choose air.
3 · Managing the air Fins, baffles, cowlings and cowl flaps; why the rear cylinders run hottest; the CHT gauge.
4 · Flying it Climb, descent and shock cooling, ground running, mixture and shut-down.
Chapter 4 · Piston Engine Cooling
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this lesson. First we ask why an engine needs cooling at all: where the heat from the fuel ends up, and what goes wrong if the engine is too hot, and also if it is too cold. Second, we look at the two ways of getting rid of the heat: liquid cooling, with water and glycol pumped through jackets to a radiator, and air cooling, with fins standing in the slipstream, and we see why almost every light aircraft uses air. Third, we look at how the cooling air is managed: fins, baffles, cowlings and cowl flaps, why the rear cylinders run hottest, and how the cylinder head temperature gauge works. Finally we fly it: what you do in the climb, the descent, on the ground, with the mixture, and at shut-down.
Part 1 · Why cool?
Most of the fuel’s energy becomes heat A piston engine is a heat engine : at best only about 25–30% of the fuel’s energy becomes useful work About 40% leaves in the exhaust (a turbocharger can recover some of it) Roughly the remaining 30% soaks into the cylinders, pistons, valves and oil That heat must be removed by the cooling system and the oil Exam figure: maximum thermal efficiency of a typical piston engine is about 30%
Where the fuel’s heat goes
28%
40%
32%
Useful work at the shaft
97 kW
Carried away in the exhaust
139 kW
Into the engine: cooling air and oil
111 kW
Worked example: 40 litres of Avgas an hour
40 L × 0.72 kg/L × 43.5 MJ/kg ÷ 3.6 = 348 kW of heat
Only about 97 kW (≈ 131 hp) turns the propeller.
About 111 kW must be removed by the cooling air and oil,
every second the engine runs.
Chapter 4 · Piston Engine Cooling
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A piston engine is a heat engine. It burns fuel to release heat, and turns part of that heat into work at the propeller. Only part, though: even a good engine converts no more than about twenty-five to thirty per cent. Roughly forty per cent goes straight out of the exhaust pipe, and a turbocharger can win a little of that back. The remaining thirty per cent or so soaks into the cylinders, heads, pistons, valves and oil, and that is the heat the cooling system must remove. Look at the worked example. An engine burning forty litres of Avgas an hour releases about three hundred and fifty kilowatts of heat. Only about ninety-seven kilowatts, roughly a hundred and thirty horsepower, turns the propeller, while about a hundred and ten kilowatts has to be carried away by the cooling air and the oil, continuously, every second the engine runs.
Part 1 · Why cool?
The problems of running too hot Structural failure : aluminium heads lose strength, cylinders crack, pistons burnOil overheats : it thins and breaks down, losing its lubricating propertiesPre-ignition : a glowing hot spot fires the mixture before the spark Detonation (knocking) : after the spark, the last of the charge explodes instead of burning smoothlyBoth pre-ignition and detonation cause a loss of power and can quickly damage the engine
Pre-ignition
a glowing hot spot fires
the charge early
Structural failure
heads crack,
pistons burn
Detonation (knock)
end gas explodes
after the spark
Oil breaks down
film thins:
wear and seizure
Pre-ignition and detonation both cost power and can wreck the engine
Chapter 4 · Piston Engine Cooling
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
What happens if the heat is not removed? Four things, and you should be able to list them. First, structural failure. Aluminium alloys lose strength quickly as they get hot, so heads can crack and pistons can burn through. Second, the oil overheats; it thins out and eventually breaks down, so it no longer keeps metal surfaces apart. Third, pre-ignition: some part of the combustion chamber, perhaps a lump of glowing carbon or an overheated plug electrode, gets hot enough to light the mixture before the spark plug fires. Fourth, detonation, also called knocking: the spark lights the charge normally, but the last part of it, the end gas, gets so hot and compressed that it explodes all at once instead of burning smoothly. Both pre-ignition and detonation cost power, and both can destroy an engine in a very short time. We look at them in detail in the fuel lesson.
Part 1 · Why cool?
…and the problems of running too cold High thermal efficiency needs high working temperatures; a cold engine wastes fuel Cold oil is thick (high viscosity) : internal friction rises More friction horsepower means less brake horsepower at the shaft Fuel vaporises poorly in a cold engine, upsetting the mixture and combustion So the aim is not “as cool as possible” but a controlled temperature
BHP = IHP − FHP
brake = indicated − friction horsepower
Warm oil
BHP 180
FHP 20
Cold, thick oil
BHP 168
FHP 32
Same indicated power (200 hp) in both cases.
Cold oil raises friction: 6.7% less power at the shaft.
Also when cold: poor fuel vaporisation and
a lower thermal efficiency.
Chapter 4 · Piston Engine Cooling
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the opposite case, because an engine can also be too cold. The hotter the working gas, the better the thermal efficiency, so a cold engine simply wastes fuel. Cold oil is thick; its viscosity is high, so the engine has to work harder just to turn itself over. Engineers call that friction horsepower, and whatever is used up as friction horsepower is lost from the brake horsepower that reaches the propeller. In the worked example the cylinders produce two hundred indicated horsepower. With warm oil, friction takes twenty, leaving one hundred and eighty at the shaft. With cold, thick oil, friction takes thirty-two, leaving one hundred and sixty-eight, almost seven per cent less. And in a cold engine the fuel does not vaporise properly, so the mixture reaching the cylinders is uneven and burns badly. Cooling is about control, not about getting the engine as cold as possible.
Part 1 · The aim
The highest temperature consistent with safe operation
Engine operating temperature: colder → hotter
relative effect
The working window
“highest temperature consistent
with safe operation”
thick oil, poor vaporisation
thermal efficiency
risk of detonation,
pre-ignition,
oil breakdown
A cooling system’s job is to hold the engine in this window despite changes in outside air temperature, power and airspeed .
Chapter 4 · Piston Engine Cooling
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Put the two lists together and you get the aim of every cooling system. On the left of the graph, the engine is too cold: thick oil, poor vaporisation and low efficiency. As the temperature rises, the thermal efficiency improves. But at the hot end the risk of detonation, pre-ignition and oil breakdown climbs very steeply. So the engine should run at the highest temperature consistent with safe operation, which is the green window in the middle. Learn that phrase; it is the textbook answer. The difficulty is that the outside air temperature, the power setting and the airspeed all change during a flight, sometimes quickly. The cooling system, together with the pilot, has to keep the engine inside the window through all of those changes.
Part 2 · Liquid cooling
Liquid cooling: jackets, pump and radiator Water and glycol (anti-freeze) is pumped through passages round the cylinders and heads An engine-driven pump circulates it; a thermostat controls the temperature Hot coolant goes to an air-cooled radiator placed in the propeller slipstream , so it works even when stationary A header tank stores the coolant and feeds the system The heat ends up in the air either way: liquid simply carries it to the radiator
Radiator
slipstream
Engine
jackets round cylinders
Header tank
Thermostat
Engine-driven pump
hot
cooled
water + glycol
Chapter 4 · Piston Engine Cooling
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a liquid-cooled engine, a mixture of water and glycol, which is anti-freeze, flows through passages built into the cylinders and cylinder heads, called jackets. An engine-driven pump keeps it moving. Watch the scene. When the engine is cold, a thermostat stays shut and the coolant simply circulates round the engine, so it warms up quickly. As the temperature reaches its working value, the thermostat opens and sends the hot coolant to the radiator. The radiator is an air-cooled heat exchanger mounted in the propeller slipstream, so air flows through it even when the aircraft is standing still. Cooled coolant returns to the pump and round again. A header tank above the engine stores the coolant and keeps the system full. Notice that the heat still ends up in the air; the liquid just carries it neatly to one place.
Part 2 · Air cooling
Air cooling: fins in the slipstream The propeller slipstream and the aircraft’s forward speed blow air straight over the cylinders Fins on the barrels and heads give a large cooling areaThe engine is cowled to cut drag and to guide the air evenly over every cylinder Some installations have a fan behind the propeller for a more uniform flow Pistons, valves and bearings inside are cooled by the oil
slipstream + speed
warm air out
Fins: more area, about 5 per inch
Head: deepest fins
Piston cooled by oil
Chapter 4 · Piston Engine Cooling
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most aero piston engines are air-cooled. There are no jackets and no radiator: the cooling air from the propeller slipstream and the aircraft’s forward speed blows directly over the cylinders and carries the heat away. To make that work, the barrels and heads are covered in thin fins, which give a very large surface for the air to pick heat from. The head, around the valves and the exhaust port, is the hottest part, so its fins are deepest. The whole engine is cowled. The cowling cuts drag, and just as important, it guides the air evenly so that every cylinder is cooled and the front of the engine is not overcooled while the back cooks. A few installations add a fan behind the propeller to make the flow more uniform. And remember that the moving parts inside, the pistons, valves and bearings, are cooled from inside by the oil.
Part 2 · Choosing
Liquid cooling or air cooling? Liquid cooling Air cooling Efficiency of cooling More efficient ; even, controlled temperaturesLess efficient; front and rear cylinders differ Temperature control Better : thermostat; allows tighter tolerancesBy airspeed and cowl flaps Drag Less drag : small radiator, slim noseMore drag from cooling air through the cowling Weight Heavier: coolant, pump, radiator, pipes Lighter for the same powerSimplicity and cost More parts; possible leaks Simple , few moving parts, nearly maintenance-free, cheaperWhere used Powerful high-speed engines; many aero-diesels Almost all light aircraft piston engines
Exam line: liquid cooling is the most efficient ; air cooling is the most common because of its lower cost , weight and simplicity.
Chapter 4 · Piston Engine Cooling
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
So which is better? Liquid cooling is the more efficient method. It holds the engine at an even, controlled temperature, which lets designers use tighter tolerances between moving parts, and a neat radiator makes less drag than pushing cooling air through a big cowling. That is why very powerful high-speed engines used it, and why many modern aero-diesels are liquid-cooled or use a combined liquid and air system. Its drawbacks are extra weight, extra parts, and the risk of leaks. Air cooling has few moving parts, is almost maintenance-free, is lighter for the same power and costs less. For a light aircraft those advantages win, so air cooling is by far the most common. If an exam asks: the most efficient is liquid cooling, the most common is air cooling, because of reduced costs.
Part 2 · Layout and cooling
How the cylinder layout affects cooling The cylinder arrangement depends partly on the cooling system used Radial : every cylinder sits in the airflow, but the frontal area (drag) is largeInline : rear cylinders sit in the wake of the front ones: hard to air-coolHorizontally opposed (flat) : slim and low drag; relies on baffles to share the airIn any air-cooled engine, the rearmost cylinders usually run hottest
Radial: every cylinder
faces the air (big frontal area)
Flat (opposed): low
frontal area, needs baffles
rear cylinders run hottest
Chapter 4 · Piston Engine Cooling
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The way the cylinders are arranged depends partly on how the engine is cooled. A radial engine, like the one turning here, puts every cylinder out in the oncoming air, so each gets a fair share of cooling. The price is a large frontal area and so a lot of drag. An inline engine is slim, but its rear cylinders sit in the wake of the front ones, which makes air-cooling difficult; many powerful inline engines were liquid-cooled for exactly that reason. The horizontally opposed, or flat, engine used in most light aircraft is a compromise: slim and low in drag, but it depends on carefully sealed baffles to share the air between the cylinders. Even so, in any air-cooled engine the rearmost cylinders usually run hottest, a point we will come back to when we fit the temperature probe.
Part 3 · Managing the air
What decides how well air cooling works
air temperature
airflow speed
fins
cylinders: aluminium alloy
baffles seal against the cowling
cowl flap
Air temperature Heat goes faster into colder air . It varies with climate and with altitude.
Speed of the airflow Set by the slipstream and airspeed . Low on the ground and in a slow climb: overheating risk.
Cooling fins Large area, thin section, about five to the inch ; deeper round hot spots such as the exhaust port.
Baffles Close-fitting air guides that seal against the cowling and force all the air over the cylinders.
Materials Metals of high heat conductivity , mainly aluminium alloys; steel heads may have copper on the chamber face.
Cowlings and cowl flaps Smooth, dent-free cowlings; cowl flaps or gills vary the flow at the exit.
Chapter 4 · Piston Engine Cooling
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Six things decide how well an air-cooled engine sheds its heat. The air temperature: heat moves faster into colder air, and that changes with the climate and with altitude. The speed of the airflow, which comes from the slipstream and the aircraft’s speed; it is lowest on the ground and in a slow climb, which is when engines overheat. The fins: plenty of area, but not so close together that they choke the flow. The baffles, which steer every bit of the air over the cylinders. The materials: designers use metals that conduct heat well, mostly aluminium alloys, and where a head is made of steel the combustion chamber face may carry a thick deposit of copper to help the heat flow out. And finally the cowling, which must be smooth and dent-free, and on many aircraft has cowl flaps, sometimes called gills, at the exit. We take these one at a time.
Part 3 · Fins
Fins: as much area as the air allows Fins add surface area , so more heat passes into the air Fins too close together resist the flow: pressure builds, flow falls and drag rises A typical compromise: about five fins to the inch Fins are thin , and made deeper at hot spots (e.g. round the exhaust port) to even out temperatures A damaged or broken fin leaves a local hot spot
Fin pitch and area
pitch ≈ 5.1 mm (5 per inch)
too close: air chokes,
pressure builds, drag rises
too far apart: too little area
Worked example: one barrel
Barrel 130 mm across, 100 mm finned length
Bare surface: π × 0.13 × 0.10 = 0.041 m²
19 fins, 25 mm deep, two faces each: 0.46 m²
Total ≈ 0.50 m²: about 12 times the bare barrel
Fins are made deeper round hot spots such as the exhaust port.
Chapter 4 · Piston Engine Cooling
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fins work by adding surface area. Heat leaves the metal through its surface, so more surface means more heat into the air. The worked example shows how big the effect is. A barrel a hundred and thirty millimetres across with a hundred millimetres of finned length has a bare surface of about four hundredths of a square metre. Add nineteen fins, each twenty-five millimetres deep, and the total area grows to about half a square metre, roughly twelve times as much. But there is a limit. If the fins are packed too closely, the narrow gaps resist the airflow, pressure builds up ahead of them, less air gets through, and drag rises. The usual compromise is about five fins to the inch, a pitch of about five millimetres. Fins are thin, and they are made deeper wherever there is a local hot spot, such as round the exhaust port, to keep the temperature even across the component.
Part 3 · Baffles and cowling
Baffles make every bit of air do some cooling
high pressure above: ram air from the intakes
low pressure below: out past the cowl flap
Baffles and cowling
Baffles
guide all the air through the fins
and seal against the cowling
Inter-cylinder baffles
force air round the back of
each barrel, not past it
Even cross-section
air keeps its speed: less drag
Smooth cowling
no dents: dents add drag
and spoil cooling
Front view, flat engine
Leaky baffles or dented cowlings let air bypass the fins: cooling falls and drag rises.
Chapter 4 · Piston Engine Cooling
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
This is a front view of a flat engine inside its cowling. Air rams in through the intakes at the front and fills the space above the cylinders, so the pressure there is high. Below the engine, where the air leaves past the cowl flap, the pressure is low. The baffles are close-fitting sheet-metal guides, sealed against the cowling, that make sure the only way from the high-pressure side to the low-pressure side is through the fins. Inter-cylinder baffles wrap round under each barrel so the air is pulled round the back of the cylinder instead of skipping past it. Designers keep the cross-section of the passages even, so the air does not slow down and create drag. And the cowling itself must be smooth and free of dents or projections; anything that disturbs the designed flow both increases drag and reduces cooling.
Part 3 · Cowl flaps
Cowl flaps (gills): a valve on the cooling air Hinged flaps at the rear of the cowling , where the cooling air leaves Open : the airflow past them lowers the exit pressure , so more air flows over the engineMore cooling, but more drag Closed : less flow, less cooling, less dragHeated air expands and speeds up through a well-shaped exit, giving a small reactive thrust that offsets drag
Closed: less flow, less drag
engine
Open: more flow, more cooling, more drag
engine
The cowl flap lowers the pressure at the cooling-air exit
Chapter 4 · Piston Engine Cooling
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many higher-performance aircraft have cowl flaps, sometimes called gills, at the rear of the cowling where the cooling air leaves. Watch the flap open. The outside air flowing past the open flap creates a low-pressure area at the exit, so the heated air is drawn out more easily and more air flows over the cylinders. Cooling improves, and the cylinder head temperature comes down. The price is drag: an open cowl flap sticks out into the airflow. Closing the flaps reduces the flow, the cooling and the drag. There is one more subtle point. As the air flows over the cylinders it picks up heat and expands, and with a well-designed exit it speeds up as it leaves. That gives a small reactive thrust that partly offsets the drag of the cooling system. On simple aircraft without cowl flaps, the only way the pilot can change the cooling flow is with airspeed.
Part 3 · Hottest and coolest
Which cylinder runs hottest? The front cylinders meet the coolest, fastest air The rear cylinders get air already warmed and partly shadowed by the others So in an inline engine numbered from the front, No. 1 is the coolest and the rearmost is the hottest If only one CHT sensor is fitted, it goes on the hottest cylinder , usually a rear one Then the gauge shows the worst case: if that cylinder is safe, the others are too
air
No. 1
165 °C
No. 2
180 °C
No. 3
192 °C
No. 4
205 °C
CHT probe ↓
illustrative cylinder head temperatures
Rear cylinders get warmer, shadowed air: they run hottest.
A single CHT probe goes on the hottest cylinder.
Front cylinder No. 1 is the coolest.
Chapter 4 · Piston Engine Cooling
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Not every cylinder runs at the same temperature. The front cylinders meet the cooling air first, while it is still at its coolest and fastest. By the time the air reaches the rear cylinders it has already picked up heat, and those cylinders are partly shadowed by the ones in front. So in an inline four numbered from the front, number one is the coolest cylinder, and number four, at the rear, is the hottest. In a flat engine it is again usually one of the rearmost cylinders. This matters for the gauge. If an aircraft has only one cylinder head temperature sensor, it is fitted to the hottest cylinder, so the gauge always shows the worst case. If that cylinder is within limits, you know the others are too. Exam questions love this: the coolest is number one, the probe goes on the hottest, usually at the rear.
Part 3 · The CHT gauge
The cylinder head temperature gauge The sensor is a thermocouple : two dissimilar metals joined at a hot junction It generates a small voltage proportional to temperature : it needs no aircraft power Often fitted as a gasket or bayonet under the spark plug of the hottest cylinder The indicator is a sensitive moving-coil galvanometer , scaled in temperature , not volts The EGT gauge uses the same principle
Hot junction
under the spark plug of the
hottest cylinder
iron
constantan
CHT
Galvanometer
scale reads temperature
Two dissimilar metals joined: the junction makes
a small voltage that rises with temperature.
Example: about 52 µV per °C, hot junction 200 °C,
instrument end 30 °C → 170 × 52 µV ≈ 8.8 mV
Self-generating: no aircraft power is needed.
The same principle drives the EGT gauge.
Chapter 4 · Piston Engine Cooling
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Many aircraft have a cylinder head temperature gauge, usually shortened to C H T. Its sensor is a thermocouple: two wires of different metals, often iron and constantan, joined at one end. When that junction is heated, it generates a small voltage that rises in step with the temperature difference between the hot junction and the instrument end. The thermocouple makes its own voltage, so the gauge works without any aircraft electrical power. In the example, about fifty-two microvolts per degree, with a hundred and seventy degrees of difference, gives under nine millivolts, which is why the indicator must be a very sensitive moving-coil meter, a galvanometer. Its scale is marked in degrees, not volts. The sensor is often a gasket or bayonet fitting under the spark plug of the hottest cylinder. The exhaust gas temperature gauge works on exactly the same principle.
Part 4 · Flying it
The climb: high power, low airspeed The climb combines high power (lots of heat) with reduced airspeed (less cooling air) Watch CHT and oil temperature: this is the classic overheating case Prefer the best rate of climb speed V Y to a prolonged climb at the best angle speed V X For a long climb, a faster cruise climb cools better still Cowl flaps open ; keep the mixture rich enough at high power
V X: steepest
slow, high power: hot
V Y: fastest climb
more airflow: cooler
Cooling airflow goes roughly with airspeed:
climbing at 74 kt instead of 62 kt gives about 19% more
air through the cowling at the same full power.
Chapter 4 · Piston Engine Cooling
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The cooling system is designed so that in normal flight the aircraft’s forward speed gives plenty of cool air. The climb is where that can break down, because it combines high power, which makes lots of heat, with reduced airspeed, which means less cooling air. So watch the cylinder head and oil temperatures in the climb. If you need to climb for a long time, use the best rate of climb speed, V Y, rather than the best angle speed, V X. V X is steeper but slower, and a prolonged climb at V X can overheat the engine. In the example, climbing at seventy-four knots instead of sixty-two gives roughly nineteen per cent more cooling air for the same power. A cruise climb, a little faster again, is even better. Keep the cowl flaps open, and keep the mixture rich enough, because extra fuel helps cool the cylinders at high power.
Part 4 · Flying it
The descent: overcooling and thermal shock In a descent, power is low (little heat) and airspeed is high (lots of cooling air) A dive with the power off can overcool the engine very quickly A sudden temperature change causes thermal shock : parts contract unevenly and can crack , cylinders especially Reduce power gradually , keep some power on, and close the cowl flaps On simple aircraft, the pilot controls cooling with airspeed
0
1
2
3
4
5
6
40
70
100
130
160
190
220
time after reducing power (minutes)
CHT (°C)
gradual descent, some power
power off, dive
Initial cooling rate: about 10 °C/min in the gradual descent
but about 70 °C/min with the power off in a dive.
Rapid change = thermal shock: cracked heads and barrels.
Chapter 4 · Piston Engine Cooling
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Descending brings the opposite problem. Power is reduced, so there is less heat being made, and if you lower the nose the airspeed rises, which pushes more cold air over the engine. Put the aircraft into a dive with the throttle closed and the engine can be overcooled very quickly. Look at the illustrative graph. In a gradual descent with some power on, the head temperature falls slowly, about ten degrees a minute at first. In a power-off dive it plunges, perhaps seventy degrees a minute. The hot cylinder head contracts faster than the parts around it, and the sudden change, called thermal shock, can crack cylinders and heads. Cylinder cracking is a common result. So plan your descents: reduce power gradually, keep some power on, close the cowl flaps if you have them, and on a simple aircraft use a sensible airspeed rather than a steep dive.
Part 4 · Flying it
Cowl flap settings through a flight Phase Cowl flaps Why Start-up and ground running Open Only the propeller slipstream cools the engine Take-off Open Maximum power, lowest airspeed; accept the extra drag Climb Open (or as needed for CHT)High power, reduced airspeed Cruise at altitude Partly closed or closed Colder air and higher speed cool better; less drag Descent Closed Low power, high speed: avoid overcooling and shock cooling After landing, taxi and shut-down Open Low speed again; let the engine stabilise
Always follow the aircraft flight manual. The pattern is simple: open when power is high and airspeed low, closed when power is low and airspeed high.
Chapter 4 · Piston Engine Cooling
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how cowl flaps are typically used through a flight. Always follow your own aircraft’s flight manual, but the pattern is logical. On the ground, only the propeller slipstream cools the engine, so the flaps are open. For take-off the flaps are open: the engine is at maximum power and the airspeed is low, so you accept the extra drag in exchange for cooling. In the climb they stay open, or are set to keep the cylinder head temperature in range. In the cruise at altitude the cooling air is colder and the speed is higher, so the flaps can be partly closed or closed to hold the engine temperature and reduce drag. In the descent they are closed to avoid overcooling. And after landing, with low speed again, they are opened for taxiing and shut-down. Open for high power and low speed, closed for low power and high speed.
Part 4 · Flying it
Ground running: the slipstream is all you have On the ground there is no forward speed : only the propeller slipstream cools the engine Limit high power and long runs on the ground; face into wind where possible Monitor CHT and oil temperature closely during run-ups The engine’s internal parts, pistons and valves, are cooled by the lubricating oil Liquid-cooled engines are less affected: the radiator sits in the slipstream
Ground running
engine
only the propeller slipstream cools it
Head into wind, cowl flaps open
Keep power and running time low
Watch CHT and oil temperature
Pistons and valves are cooled by the oil
Chapter 4 · Piston Engine Cooling
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the ground the aircraft has no forward speed, so the only cooling air is what the propeller slipstream pushes through the cowling. At low power that is not much, and at high power the engine is making much more heat than the slipstream can easily remove. So keep high-power ground running to a minimum, keep run-ups short, face into wind where you can, and open the cowl flaps. Monitor the cylinder head and oil temperatures closely while you are on the ground, because this is where overheating sneaks up on you. And do not forget the inside of the engine. The pistons, valves and bearings are cooled by the lubricating oil, which is why a high oil temperature is just as important a warning as a high cylinder head temperature.
Part 4 · Flying it
Mixture and cylinder head temperature Mixture strength strongly affects CHT (details in the mixture lesson) A rich mixture: the extra fuel absorbs heat as it evaporates, so the cylinders run cooler Leaning for economy or endurance cruise gives the highest cylinder head temperatures That is why high power is always flown rich , and leaning is done at cruise power Exam point: highest CHT with a lean mixture selected for economy
mixture: full rich → leaner
temperature and power (relative)
EGT
CHT
power
rich: extra fuel cools
the cylinders
Leaning towards economy raises CHT; the extra
fuel in a rich mixture carries heat away.
Illustrative curves; exact shapes vary with the engine.
Chapter 4 · Piston Engine Cooling
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The mixture you select also has a strong effect on the cylinder head temperature; we study it fully in the mixture lesson, but here is the cooling side of it. In a rich mixture there is more fuel than the air can burn. That extra fuel absorbs heat as it evaporates and passes through, so the cylinders run cooler. That is why take-off and climb power are always flown with a rich mixture. As you lean towards an economical cruise setting, the cooling effect of the spare fuel disappears and the head temperature rises. On the illustrative graph, best power comes first, the cylinder head temperature peaks a little leaner, and the exhaust gas temperature peaks leaner still. For the exam, remember the simple rule: the highest cylinder head temperatures occur when a lean mixture is selected for economy or endurance cruise.
Part 4 · Flying it
Shut-down and other uses of engine heat The taxi in lets temperatures cool and stabilise before shut-down Shutting down while very hot causes uneven cooling and possible damage Just before shut-down, run briefly at about 1000–1200 RPM to keep the plugs from fouling Waste heat is put to use: air warmed over the exhaust heats the cabin and, when selected, supplies carburettor heat to clear induction ice
exhaust
Heater muff
Hot-air shroud
Cabin heat
Carburettor heat
when selected
to clear induction ice
fresh air passes over the hot pipe
Waste heat put to work
Chapter 4 · Piston Engine Cooling
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Shut-down needs a little care too. During the taxi back to the parking area, the low power lets the engine temperatures come down and settle. Shutting down an engine that is still very hot means its parts cool unevenly once the airflow and the oil circulation stop, which can cause damage. Just before shut-down, running the engine for a short time at about one thousand to one thousand two hundred RPM helps prevent the spark plugs from fouling. Finally, not all the engine’s heat is wasted. Fresh air passed over the hot exhaust pipe, through a heater muff, is used to warm the cabin. And air heated in a shroud round the exhaust is used, when the pilot selects it, as carburettor heat to melt ice in the induction system, a topic with its own lesson later in the course.
Summary
What to take into the exam Heat budget At best about 30% useful work; ~40% exhaust; ~30% into the engine and oil.
Too hot / too cold Hot: structural failure, oil breakdown, pre-ignition, detonation. Cold: thick oil, more FHP, poor vaporisation.
The aim Highest temperature consistent with safe operation .
Liquid vs air Liquid: most efficient , less drag, better control. Air: most common , lighter, simpler, cheaper.
Fins and baffles About 5 fins per inch ; baffles seal on the cowling and force air round the cylinders.
Cowl flaps Open on the ground, take-off and climb; closed in the descent; partly closed in cruise.
CHT gauge Thermocouple on the hottest (rear) cylinder; galvanometer reads temperature. No. 1 at the front is coolest.
Operating Climb at V Y , not V X; avoid power-off dives (shock cooling ); lean mixture = highest CHT.
Chapter 4 · Piston Engine Cooling
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull it together. At best about thirty per cent of the fuel’s energy becomes useful work; about forty per cent leaves in the exhaust and about thirty per cent soaks into the engine and oil. Too hot means structural failure, oil breakdown, pre-ignition and detonation. Too cold means thick oil, more friction horsepower and poor vaporisation. The aim is the highest temperature consistent with safe operation. Liquid cooling is the most efficient and makes less drag; air cooling is the most common because it is lighter, simpler and cheaper. Fins are about five to the inch, and baffles seal against the cowling to force the air round the cylinders. Cowl flaps are open on the ground, for take-off and in the climb, and closed in the descent. The C H T sensor is a thermocouple on the hottest, rear cylinder. Climb at V Y, avoid power-off dives, and remember a lean mixture gives the highest head temperatures.