Engines · Chapter 9
Induction and Carburettor Icing Impact, refrigeration and fuel ice in the induction system: why a carburettor can ice up on a warm day, how to recognise it, and how to use carburettor heat.
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter nine is about induction icing, and especially carburettor icing, which still causes accidents every year. The surprising thing is that it needs no cold weather at all: on a warm, damp day the inside of a carburettor can fall well below freezing. We will look at the three forms of induction ice, why a carburettor gets so cold, the temperatures and humidity that bring the risk, how to recognise ice early, and how to use carburettor heat properly, together with its penalties. We finish with fuel-injected and diesel engines.
Chapter 9 · Roadmap
Ice in the induction system 1 · Three forms of ice Impact ice, refrigeration (carburettor) ice and fuel ice, and where each collects.
2 · Why and when Fuel evaporation and the venturi cool the air by about 20 °C: icing from −7 to +33 °C in humid air.
3 · Heat and procedures Symptoms, carburettor heat and its penalties, and what to do on the ground, in flight and in descent; injected and diesel engines.
Chapter 9 · Induction and Carburettor Icing
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This chapter has three parts. First, the three forms of ice that can block a piston engine's induction system: impact ice, refrigeration ice, which is what we usually mean by carburettor ice, and fuel ice, and where each one collects. Second, why and when it happens: how evaporating fuel and the venturi can cool the air by twenty degrees or more, and the surprisingly wide range of temperatures, from about minus seven to plus thirty-three, in which humid air can ice up a carburettor. Third, what to do about it: the symptoms, the carburettor heat system and its penalties, and the correct procedures on the ground, at take-off, in the cruise and in the descent, finishing with fuel-injected and diesel engines.
Part 1 · Three forms of ice
Why induction icing matters Induction icing still causes accidents , despite modern fuel metering It can happen in all types of piston engine induction system, worst with float carburettors Conditions: high humidity (above about 50% RH ) and temperatures from about −7 °C to +33 °C Those conditions are common all year round , including warm, humid days Once ice stops the engine, a restart in time is most unlikely : recognise and act early
Outside air temperature, °C
carburettor icing possible
-20
-7
0
+15
+33
+40
Relative humidity
above about 50%
0%
50%
100%
Engine stopped by induction ice:
a restart in time is most unlikely
Chapter 9 · Induction and Carburettor Icing
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Induction icing has been understood for decades, yet it still causes accidents, even with modern fuel metering. It can affect the induction system of every type of piston engine, but the float carburettor is the most vulnerable. The conditions are not what most people expect. You do not need freezing weather; you need humid air, with relative humidity above about fifty per cent, at temperatures anywhere from about minus seven to as high as plus thirty-three degrees. In much of the world, and certainly on humid days in India, those conditions are common at any time of year. The danger is that ice can build gradually until the engine stops, and once an engine has stopped because of induction ice, it is most unlikely that you will restart it in time. So the whole skill is to anticipate, recognise and correct icing early, before it becomes irretrievable.
Part 1 · Three forms of ice
Three forms of induction ice
IMPACT ICE
filter and intake bends
impact ice at bends
REFRIGERATION ICE
venturi and throttle (carburettor ice)
FUEL ICE
water from the fuel, at manifold bends
air in
to cylinders
Impact ice : supercooled water or snow striking the filter and bends. Refrigeration ice : cooling in the carburettor freezes the moisture in the air. Fuel ice : water in the fuel freezes in the cold carburettor and sticks downstream.
Chapter 9 · Induction and Carburettor Icing
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three forms of induction ice, and they collect in different places. Impact ice forms when supercooled water droplets or wet snow strike the air filter and the bends of the intake and freeze there; it is the same process that ices the wing, so it needs freezing conditions. Refrigeration ice is carburettor ice. It forms inside float-type carburettors because evaporating fuel and the low pressure in the venturi cool the incoming air so much that the moisture in it freezes, even when the outside air is warm. It builds in the venturi and round the throttle valve. Fuel ice is caused by water held in the fuel coming out of suspension and freezing in the cold carburettor. It tends to stick to the inlet manifold around the corners and bends, again reducing the flow of mixture to the engine.
Part 2 · Why and when
Why a carburettor gets so cold Fuel evaporation takes its latent heat from the air: the main cooling effectThe low pressure in the venturi cools the air a little more The air can fall about 22 °C below the inlet temperature Moist air at +15 °C can drop below 0 °C : the moisture freezes Ice builds downstream of the nozzle , on the venturi wall and round the throttle butterfly
Where the cold comes from
Fuel evaporation (15:1)
≈ 23 °C
Fuel evaporation (12.5:1)
≈ 28 °C
Venturi expansion
≈ 1–2 °C
ΔT ≈ latent heat ÷ (air/fuel ratio × cp)
= 350 ÷ (15 × 1.005) ≈ 23 °C if all the fuel evaporated
Inlet air +15 °C, humid → throttle area about −7 °C
a drop of about 22 °C is the classic figure: ICE
Chapter 9 · Induction and Carburettor Icing
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does a carburettor get so cold? Mostly because of the fuel. To turn from liquid into vapour, fuel needs its latent heat of vaporisation, and it takes that heat from the air around it. Here is a quick energy balance. Aviation gasoline needs about three hundred and fifty kilojoules per kilogram to evaporate. In a fifteen to one charge there are fifteen kilograms of air to share that cooling, so if all the fuel evaporated, the air would cool by about twenty-three degrees. The low pressure in the venturi adds a little more, only a degree or two. The classic figure is a drop of about twenty-two degrees below the temperature of the incoming air. So moist air entering at plus fifteen can fall to minus seven, and its moisture freezes. In the scene you can see where the ice builds: on the venturi wall downstream of the nozzle and round the throttle butterfly.
Part 2 · Why and when
The carburettor icing chart
-10
-5
0
+5
+10
+15
+20
+25
+30
+35
-20
-10
0
+10
+20
+30
Air temperature, °C
Dew point, °C
100% RH
50% RH
Serious icing: any power
Moderate icing cruise power
serious icing descent power
Serious icing: descent power
Light icing: cruise or descent power
approximate; after the published
carburettor icing chart
Read it with the temperature and dew point from the METAR. The nearer the dew point is to the temperature (high humidity), the worse the risk; descent power is always the worst case.
Chapter 9 · Induction and Carburettor Icing
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
This chart is the pilot's tool for judging the risk before flight. Along the bottom is the air temperature, up the side the dew point, and the dashed lines are relative humidity. Plot the temperature and dew point from the weather report. The darkest band, close to the hundred per cent line between about minus five and plus twenty degrees, is serious icing at any power. Around it is a band of moderate icing at cruise power but serious icing at descent power, reaching up to about twenty-seven degrees. Wider still, down to about fifty per cent humidity and up to about thirty-three degrees, there is serious icing at descent power, and beyond that light icing at cruise or descent power. Two lessons stand out. Humid air is the key ingredient, and descent power, with the throttle nearly closed, is always the worst case.
Part 2 · Why and when
Why low power is the worst case Ice is most likely at part throttle and low power : descent, approach, taxi and idle With the throttle nearly closed, ice at its edge blocks a large share of the small gap High local speed past the plate gives extra cooling right at the throttle At low power the engine is cooler , so the heat available to fight ice is less With a wide-open throttle intake icing is unlikely
Wide open
ice blocks ≈ 10% of the gap
Nearly closed (low power)
ice blocks ≈ 60% of the gap
Same ice, very different effect
and at low power the engine is cooler: less heat available
Chapter 9 · Induction and Carburettor Icing
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Carburettor icing is most likely in the choke tube at low power: during a glide descent, on the approach, while taxiing, or at idle. There are several reasons. With the throttle nearly closed, the air squeezes through a narrow gap round the edge of the plate, so a thin layer of ice there blocks a large share of the remaining flow area, while the same ice on a wide-open throttle hardly matters. In the scene, watch the small gap round the plate close up. The air rushing through that gap also cools further. And at low power the whole engine runs cooler, so there is less heat around the carburettor and less heat available to the carburettor heat system as well. By contrast, intake icing should not occur at the high power settings that involve a wide throttle opening, which is one reason why carburettor heat is not needed, and not wanted, at high power.
Part 2 · Why and when
Recognising carburettor ice Fixed-pitch propeller : a gradual, unexplained drop in RPM , then rough running and vibrationConstant-speed propeller : RPM stays constant; look for a drop in manifold pressure In level flight with constant power settings, airspeed falls Left alone: ice blocks the intake and may jam the throttle , then the engine stops Below about −10 °C the moisture is already frozen and passes through: little carb icing
Fixed-pitch propeller
RPM 2400 → 2250
gradual RPM drop
rough running, vibration
Constant-speed propeller
MAP inHg 24 → 21
RPM held by the governor
MAP falls, airspeed falls
If not caught: ice blocks the intake
and can jam the throttle, then the engine stops.
A restart in time is most unlikely.
Chapter 9 · Induction and Carburettor Icing
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
If you have not anticipated the ice, how will you notice it? With a fixed-pitch propeller, the first sign is a gradual drop in R P M, often put down to something else, followed by rough running and vibration. With a constant-speed propeller, the governor holds the R P M constant, so the R P M gauge tells you nothing. Watch the manifold pressure instead: it falls as the ice restricts the airflow, and in level flight the airspeed falls too. That is a favourite exam trap. If the ice is not cleared, it keeps reducing the intake area, can stop the throttle plate moving, and finally blocks the intake and stops the engine. One more point: in really cold air, well below freezing, around minus ten degrees, the moisture is already frozen into ice crystals that pass straight through, so carburettor heat is not normally needed there.
Part 3 · Heat and procedures
The carburettor heat system A cockpit control works a flap in the air box ahead of the carburettor COLD: filtered ram air . HOT: air warmed in a muff round the exhaust Hot air bypasses the air filter : unfiltered The heat melts the ice , which passes through the engine as water Partial heat only with a carburettor air temperature (CAT) gauge
COLD: filtered ram air
heat muff (shroud) round the exhaust
exhaust
HOT: unfiltered
air box flap
carb
CAT °C
yellow: icing range
Chapter 9 · Induction and Carburettor Icing
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The cure for carburettor ice is heat, and the carburettor heat system is simple. A cockpit control moves a flap in the air box just ahead of the carburettor. In the COLD position the engine breathes filtered ram air from the intake. Pull the control to HOT, as in the scene, and the flap shuts off the cold air and opens a duct from a muff, a sheet-metal shroud wrapped round the exhaust pipe, so the engine breathes air that has been warmed by the exhaust. Note that this hot air bypasses the air filter, so it is unfiltered. The warm air melts the ice, and the water passes through the engine. Some aircraft have a carburettor air temperature gauge, with a yellow arc marking the icing range. Only with such a gauge should you use partial heat, because partial heat could actually raise a very cold intake temperature into the icing range.
Part 3 · Heat and procedures
What carburettor heat does to the engine Hot air is less dense : less mass of charge, about 15% less power Same fuel for less air: the mixture becomes richer , perhaps rough running With no ice present: RPM falls (fixed pitch) and CHT rises Above about 80% power the hot charge risks detonation and engine damage In hot, dry weather heat may cause a rich cut ; do not use it from habit
Carb heat ON, no ice present
Intake air
+15 °C → +65 °C
Air density
−15 %
Power
about −15 %
Mixture
RICHER (same fuel, less air)
RPM (fixed pitch)
falls (≈100 on the ground check)
CHT
RISES
density ratio 288 K ÷ 338 K = 0.85
Chapter 9 · Induction and Carburettor Icing
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Carburettor heat is not free. Warm air is less dense, so for the same throttle opening a smaller mass of air reaches the cylinders. Raise the intake air from plus fifteen by about fifty degrees and its density falls by about fifteen per cent, and the power falls by about the same, roughly fifteen per cent. The carburettor meters fuel by the venturi depression, so with less dense air the mixture also becomes richer, which can make the engine run roughly. So if you apply heat with no ice present, you see the R P M fall with a fixed-pitch propeller, the power fall, and the cylinder head temperature rise. At high power settings, above about eighty per cent, the hotter charge brings the engine close to detonation and can damage it. And in hot, dry weather full heat can make the mixture so rich that the engine suffers a rich cut. Use it when it is needed, not out of habit.
Part 3 · Heat and procedures
When icing is suspected Select FULL HOT and leave it there long enough to clear the ice: up to 1 minute or more Expect more roughness and power loss at first as melt water passes through Do not return to COLD thinking heat has made things worseIce cleared: RPM or MAP recovers , and settles higher than before when you return to cold Then keep checking: in icing conditions, use heat as often as needed
0
10
20
30
40
2200
2300
2400
2500
seconds
RPM
FULL HOT
ice forming
rougher: melt water
COLD: higher
keep heat on through the roughness
Chapter 9 · Induction and Carburettor Icing
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
When you suspect carburettor ice, select full hot and leave it there long enough to clear the ice, which can take up to a minute, or longer if the icing was severe. Do not use partial heat unless you have a carburettor air temperature gauge. Now be ready for what happens next. Heat reduces power anyway, and as the ice melts, the water passes into the cylinders, so the engine may run even more roughly for a while and lose more power. Many pilots have been tempted to push the control back to cold, thinking heat has made things worse. Do not. Keep it hot and the engine will smooth out. Look at the graph: the R P M dips and roughens, then recovers while heat is still on, and when you return to cold it settles higher than it was before you selected heat. That is the proof that there was ice.
Part 3 · Heat and procedures
Checking for ice in flight
0
10
20
30
40
2200
2300
2400
2500
seconds
RPM — No ice
HOT
0
10
20
30
40
2200
2300
2400
2500
seconds
RPM — Ice present
HOT
drop ≈ 100, steady
back to 2400
rough: melt water
higher than before
ice forming
Be alert in damp, cloudy, hazy weather, near cloud and in rain or drizzle . Check with heat for 15–30 s : ice was present if the RPM rises with heat on or returns higher at cold.
Chapter 9 · Induction and Carburettor Icing
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
In flight, be alert to the conditions that breed carburettor ice: damp, cloudy, foggy or hazy days, flying close to cloud, and flying in rain or drizzle. Watch the instruments for any unaccountable loss of R P M or manifold pressure, listen to the engine, and keep an eye on the outside air temperature. Make frequent checks. Note the R P M, apply full heat for between fifteen and thirty seconds and note the drop, then return to cold. Compare the two graphs. On the left there was no ice: the R P M falls by about a hundred, stays down while heat is on, and comes back to exactly where it started. On the right there was ice: the R P M rises while heat is still applied, or returns to a higher figure than the original when you go back to cold. If ice is present, continue to use heat for as long as you are in icing conditions.
Part 3 · Heat and procedures
Descent, approach and landing Long descents at reduced power (below about 1800 RPM ) are the highest risk Select full HOT before reducing power, while the engine is still hot Open up to cruise power briefly every 500–1000 ft : keeps the heat source hot and clears plug lead fouling Approach and landing: heat COLD , except for a glide approach or known icing Return to COLD before a go-around or roller landing
1 · HOT before reducing power
2 · warm the engine
every 500–1000 ft
(also clears plug lead fouling)
3 · approach: COLD unless a glide approach or icing;
back to COLD before a go-around or roller
Chapter 9 · Induction and Carburettor Icing
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The descent is the most dangerous phase for carburettor icing, because the throttle is nearly closed and the engine is cooling down. Remember that the heat comes from the engine's own exhaust, so in a long descent the hot air system gradually loses its effectiveness. So, where icing conditions exist, select full hot before you reduce power, to get the benefit of the engine while it is still hot. In a glide descent or any long period at low power, below about eighteen hundred R P M, keep the heat on, and every five hundred to a thousand feet open up to cruise power for a short time. That keeps the engine and the exhaust warm, and it also burns off the lead deposits that foul spark plugs at low power. On the approach the control normally stays at cold, except for a glide approach or known icing, and it must go back to cold before you apply power for a go-around or a roller landing.
Part 3 · Heat and procedures
On the ground, take-off and climb Keep heat use on the ground short : the air is unfiltered , so dust wears pistons and cylinders Function check before take-off: about 100 RPM drop , back to the same figure at cold Ice can form while taxiing at idle : clear it with heat, then COLD before take-off power Check that normal take-off RPM / MAP is available; never use heat during take-off Climb: no heat at power above about 80% (about 2500 RPM)
1
Taxi
icing possible at idle; keep heat use short (unfiltered air)
2
Run-up check
HOT: about 100 RPM drop; COLD: back to the same figure
3
Ice suspected
HOT to clear it, then COLD
4
Take-off
COLD before full power; check take-off RPM / MAP
5
Never
carb heat during take-off
Chapter 9 · Induction and Carburettor Icing
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
On the ground, use carburettor heat as little as possible, because the hot air is unfiltered and can carry dust and grit into the engine, wearing the pistons and cylinders. Make a function check during the run-up: with heat selected the R P M should drop by about a hundred, and it should return to the selected figure when you go back to cold. Carburettor ice can form while taxiing at small throttle settings or at idle, so if you suspect it, use heat to clear it before take-off, but always return the control to cold before opening the throttle to full power, and check that you get the normal take-off R P M or manifold pressure. Under no circumstances should carburettor heat be used during take-off: you need all the power, and you risk detonation. In the climb, and at any power above about eighty per cent, around twenty-five hundred R P M, do not use heat either.
Part 3 · Heat and procedures
When to use heat, and when not to Situation Carburettor heat Reason Suspected icing in cruise FULL HOT , long enough to clearPartial heat may make it worse Long descent, glide HOT before reducing powerEngine cooling, throttle nearly shut Take-off COLD , never hotFull power needed, detonation risk Climb, power above about 80% COLD Hot charge: detonation Ground running Minimum Unfiltered air: dust and wear Clear of icing conditions COLD Power loss, richer mixture, higher CHT Hot, dry day Only if needed May cause a rich cut Very cold air (below about −10 °C) Not normally needed Moisture already frozen; partial heat could cause icing
Chapter 9 · Induction and Carburettor Icing
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the rules in one table. If you suspect icing in the cruise, full hot, and leave it long enough to clear. For a long descent or glide, hot before you reduce power. For take-off, cold, always. In the climb, or at any power above about eighty per cent, cold, because a hot charge invites detonation. On the ground use the minimum, because the air is unfiltered. Once clear of icing conditions, go back to cold and simply check from time to time that ice has not re-formed, because continuous heat costs power, richens the mixture and raises engine temperatures. On a hot, dry day heat may cause a rich cut, so do not apply it from habit. And in very cold air, well below freezing, the moisture is already ice and passes through, so heat is not normally needed; partial heat there could even warm the air into the icing range.
Engines without carburettors
Fuel-injected engines No venturi with fuel evaporating in it: no refrigeration (carburettor) icing Still at risk: impact ice on the air filter and on impact sensing tubes , especially in cloud at low temperatures Fuel icing can gather at bends in the systemRemedy: the alternate air system (automatic spring-loaded door or manual control) Follow the aircraft checklist icing drill
impact ice
on the filter
alternate air door
warm, unfiltered, from the cowling
fuel and impact ice
at bends
throttle
no venturi, no fuel evaporating in it: no refrigeration icing
Chapter 9 · Induction and Carburettor Icing
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
A fuel-injected engine has no venturi with fuel evaporating in it, so it does not suffer from refrigeration icing, the classic carburettor ice. That does not make it immune to induction ice. Impact ice can still build on the air filter and on the impact sensing tubes that some injection systems use to measure airflow, particularly when flying in cloud at low temperatures. Fuel icing can still gather at bends in the system. Either can cause a loss of power just as serious as carburettor ice. These engines have an alternate air system instead of carburettor heat. It may be a spring-loaded door that opens automatically by suction when the filter becomes blocked, or a manual control, and it admits warm, unfiltered air from inside the cowling. When icing occurs, select alternate air and follow the icing drill in the aircraft checklist.
Engines without carburettors
Aero-diesel engines No carburettor , so no venturi and no refrigeration icingImpact ice on the air filter: an ice guard bypasses the filter when it blocks Cold makes diesel fuel wax : its viscosity rises and it may not flow Prevented by fuel additives and fuel heaters in the lines or filters So diesels avoid carburettor ice but have their own cold-fuel problem
No carburettor
no venturi, so no refrigeration icing
Ice guard
bypasses the air filter when it is blocked by impact ice
Waxing
cold fuel thickens (viscosity rises)
additives and fuel heaters in lines or filters
Chapter 9 · Induction and Carburettor Icing
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aero-diesel engines do not suffer from icing in the same way as conventional petrol engines. There is no carburettor, and therefore no venturi to attract the refrigeration icing that troubles float carburettors. They can still meet impact ice at the air inlet filter. That is dealt with by an ice guard, which effectively bypasses the filter when it becomes blocked with ice, so the engine keeps breathing. Diesels do have a cold-weather problem of their own, though. At low temperatures diesel and jet fuels can begin to wax, meaning that waxy compounds start to solidify and the fuel's viscosity rises until it may no longer flow freely through filters and lines. That is prevented by adding anti-waxing additives to the fuel, or by fitting fuel heaters in the lines or filters to warm the fuel before it reaches them.
Exam focus
Icing numbers and traps Question asks… Answer Temperature range for carburettor icing About −7 °C to +33 °C , with high humidity (above about 50% RH) Typical temperature drop in the carburettor Up to about 22 °C , mainly from fuel evaporation Where and when most likely In the choke tube / at the throttle , at low power Symptom with a constant-speed propeller Manifold pressure falls (RPM constant)Carb heat applied with no ice RPM and power fall, CHT rises , mixture richerCarb heat at high power, high temperature Risk of detonation Power loss with full carb heat About 15% Ice was present if… RPM rises with heat on, or returns higher at cold
Chapter 9 · Induction and Carburettor Icing
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the icing facts that examiners like. Carburettor icing can occur from about minus seven to plus thirty-three degrees in humid air, with relative humidity above about fifty per cent. The temperature in the carburettor can fall by up to about twenty-two degrees, mainly through fuel evaporation. Icing is most likely in the choke tube and at the throttle, at low power. With a constant-speed propeller the symptom is a fall in manifold pressure, not R P M. Carburettor heat applied with no ice present reduces R P M and power and raises the cylinder head temperature, and the mixture becomes richer. Using it at high power and high temperatures risks detonation. Full heat costs about fifteen per cent of the power. And the proof that ice was there is an R P M that rises while heat is on, or returns higher when you go back to cold.
Summary
Induction icing in six lines Three forms Impact ice (filter, bends), refrigeration ice (venturi, throttle), fuel ice (manifold bends).
Warm and humid Fuel evaporation cools the air about 22 °C: icing from −7 to +33 °C above about 50% RH.
Low power worst Part-closed throttle, descent, taxi. Fixed pitch: RPM drop. CSU: MAP drop, airspeed loss.
Full heat, long enough Expect roughness as ice melts; do not go back to cold. RPM rising = ice was there.
Heat costs About 15% power, richer mixture, higher CHT; detonation above 80% power. Never for take-off.
No carburettor? Injection: impact and fuel ice, alternate air. Diesel: ice guard; waxing prevented by heaters and additives.
Chapter 9 · Induction and Carburettor Icing
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. There are three forms of induction ice: impact ice on the filter and bends, refrigeration ice in the venturi and round the throttle, and fuel ice at the manifold bends. Carburettor ice needs humidity, not cold: fuel evaporation cools the air by about twenty-two degrees, so icing is possible from about minus seven to plus thirty-three degrees when the humidity is above about fifty per cent. Low power is the worst case. With a fixed-pitch propeller look for an R P M drop; with a constant-speed propeller, a fall in manifold pressure and airspeed. When you suspect ice, use full heat for long enough, expect roughness as it melts, and do not go back to cold. Heat costs about fifteen per cent of the power, richens the mixture and raises engine temperatures, so never use it for take-off or above about eighty per cent power. Injected and diesel engines have their own, smaller, icing problems.