Engines · Chapter 19
The Exhaust System How the exhaust unit turns the gas leaving the turbine into thrust: exhaust cone, jet pipe, propelling nozzle and choking, convergent-divergent nozzles, by-pass exhausts and noise suppression.
exhaust cone, jet pipe, nozzle choked jet: Mach 1 at the nozzle shear mixing = noise © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter nineteen follows the gas out of the back of the engine. The exhaust system is easy to underrate: it looks like a simple pipe, yet its shape decides how fast and in what direction the gas leaves, and so how much thrust the engine makes. In a turboprop it also sets the back pressure on the turbine. We will look at the exhaust cone and jet pipe, the propelling nozzle and what it means for a nozzle to be choked, convergent-divergent nozzles, the exhausts of by-pass engines, the danger areas round a running engine, and finally noise: where it comes from and how it is reduced.
Roadmap
What this chapter covers 1 · Jet pipe Exhaust cone, struts, jet pipe, temperatures and insulation, Mach 0.5 in the pipe.
2 · Nozzles The convergent propelling nozzle, choking, and the convergent-divergent nozzle.
3 · By-pass exhausts Mixers on low by-pass engines; co-axial and common nozzles on high by-pass engines; danger areas.
4 · Noise Fan, turbine and jet noise; why by-pass engines are quieter; linings, lobes and mixers.
Chapter 19 · The Exhaust System
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for the exhaust system. First, the jet pipe: the exhaust cone and support struts behind the turbine, the temperatures the pipe has to survive, how the airframe is protected, and why the gas is kept at about Mach nought point five in the pipe. Second, nozzles: the convergent propelling nozzle, what it means for it to be choked, and how a convergent-divergent nozzle squeezes out extra thrust. Third, the exhausts of by-pass engines, with their two gas streams, and the danger areas round a running engine. Finally, noise: where it comes from, why high by-pass engines are so much quieter, and how older engines were silenced.
Part 1 · Jet pipe
The exhaust unit and its job Often underrated, but its design has a big effect on performance Turbojet: gases must leave in the right direction at the best velocity for thrust Turboprop: the outlet nozzle largely sets the turbine gas temperature and back pressure Parts: exhaust cone , rear support struts , jet pipe , propelling nozzle Reheat (afterburning) engines add a burner section in the jet pipe Turbine exit to atmosphere turbine exhaust cone jet pipe propelling nozzle Gases must leave in the right direction and at the best velocity for thrust. Turboprop: the nozzle sets the turbine back pressure and gas temperature.
Chapter 19 · The Exhaust System
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The exhaust system looks like a simple pipe, so it is often underrated, yet its design has a considerable influence on how well the engine performs. In a turbojet, the gas leaving the turbine must be sent out in exactly the right direction and at the best velocity to make thrust. In a turboprop, where most of the energy has already gone into the propeller, the shape of the outlet nozzle largely decides the turbine gas temperature and the back pressure on the turbine. The basic exhaust unit has four parts: the exhaust cone, right behind the turbine; the rear support struts; the jet pipe; and the propelling nozzle at the end. Engines with reheat also carry a burner section in the jet pipe, but we leave that for the performance chapter.
Part 1 · Jet pipe
Hot gas and protecting the airframe Gas entering the exhaust: about 550 °C to 850 °C With reheat : up to about 1 500 °C A jet pipe inside the fuselage must be isolated from the structure An air gap with circulating air between pipe and skin An insulating blanket : fibrous material between thin stainless steel layers Both together: cooling air + insulation Jet pipe inside the fuselage gas 550 to 850 °C (up to 1 500 °C with reheat) aircraft skin cooling air gap stainless steel fibrous insulation stainless steel Air gap with circulating air + insulation blanket between thin stainless-steel skins: both protect the airframe.
Chapter 19 · The Exhaust System
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The gas reaching the exhaust system is still very hot, typically between five hundred and fifty and eight hundred and fifty degrees Celsius, and with reheat in use it can reach about one thousand five hundred degrees. Where the jet pipe runs through the fuselage, as in many military aircraft and some tail-mounted designs, the structure must be protected from that heat. Two things are done together. First, a clearance is left between the jet pipe and the aircraft skin, and air is allowed to circulate through it, carrying heat away. Second, the jet pipe is wrapped in an insulating blanket made of fibrous material sandwiched between thin layers of stainless steel. So the exam answer is a combination of cooling air and insulating material, not either one alone.
Part 1 · Jet pipe
Gas speed in the jet pipe Gas leaves the turbine at about 750 to 1 250 ft/s That is about Mach 0.5 in gas at this temperature A long pipe at high speed means turbulence and friction losses , less thrust So the gas is held to about Mach 0.5 in the jet pipe to minimise turbulence Speed of sound rises with temperature: a = √(γ R T) Worked example: Mach number at the turbine exit Gas temperature 700 °C = 973 K Speed of sound a = √(γ R T) √(1.33 × 287 × 973) ≈ 609 m/s ≈ 2000 ft/s 750 1000 1250 0.3 0.4 0.5 0.6 0.7 Gas velocity leaving the turbine (ft/s) Mach number M 0.38 M 0.50 M 0.63 750 to 1 250 ft/s at about 700 °C is roughly Mach 0.5
Chapter 19 · The Exhaust System
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
How fast is the gas moving in the jet pipe? It leaves the turbine at somewhere between seven hundred and fifty and twelve hundred and fifty feet per second. That sounds fast, but the speed of sound depends on temperature, and this gas is hot. At seven hundred degrees Celsius, nine hundred and seventy-three kelvin, the speed of sound in exhaust gas works out at about six hundred and nine metres per second, close to two thousand feet per second. So the gas is moving at roughly Mach nought point four to nought point six, about Mach nought point five. If it went down a long jet pipe any faster, it would create a lot of turbulence and friction, lowering efficiency and thrust. That is why the velocity in the exhaust unit is held to about Mach nought point five.
Part 1 · Jet pipe
The exhaust cone: a divergent duct in disguise Casing converges, the annulus diverges turbine exhaust cone outer casing: slightly convergent Gas annulus (blue bars) gets wider: the gas slows down The cone also keeps hot gas off the turbine disc face Computed flow area behind the turbine 0.0 0.2 0.4 0.6 0.8 0.0 0.2 0.4 0.6 0.8 Distance behind the turbine (m) Area (m²) 0.28 m² 0.66 m² Area grows ×2.4, so the gas slows before the long jet pipe
Chapter 19 · The Exhaust System
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Right behind the turbine sits the exhaust cone, and here is a subtle point the examiners love. Look at the outer casing: it seems to narrow, so you might think the duct is convergent. But the cone inside narrows much faster, so the annular space the gas actually flows through gets bigger. In this computed example the flow area more than doubles, from about nought point two eight to about nought point six six square metres, so the volume behind the turbine is divergent. That slows the gas leaving the turbine before it travels down the jet pipe, which reduces turbulence. The cone sits close to the rear face of the turbine disc, and it has a second job: it stops the hot gas flowing across the disc face, which would disturb the flow and overheat the disc.
Part 1 · Jet pipe
Turbine rear support struts The rear turbine bearing is supported inside the exhaust cone It is held by turbine rear support struts across the gas stream The struts have streamlined fairings The fairings straighten out any residual whirl left by the turbine Whirl allowed into the jet pipe would cause extra losses Rear support struts straighten the flow gas leaving the turbine with residual whirl axial flow into the jet pipe streamlined strut fairings The struts also carry the rear turbine bearing inside the cone.
Chapter 19 · The Exhaust System
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The rear bearing of the turbine shaft has to be supported somewhere, and the exhaust cone is the natural place. It is held in position by the turbine rear support struts, which cross the gas stream from the outer casing to the cone. Because they sit in fast, hot gas, the struts are covered by streamlined fairings. Those fairings do a useful second job. The gas leaving the last turbine stage is never perfectly axial; it still has a little swirl, called residual whirl. The fairings act like a row of guide vanes and straighten the flow, so the gas travels axially down the jet pipe. If the whirl were allowed into the pipe it would cause additional losses. Remember: the struts straighten out residual whirl; they do not add swirl.
Part 2 · Nozzles
The convergent propelling nozzle At the end of the jet pipe: a convergent propelling nozzle It increases the velocity and decreases the pressure of the gas In a turbojet the gas reaches Mach 1 (local speed of sound) at virtually all settings above idle At Mach 1 the nozzle is choked Subsonic only at low thrust Convergent propelling nozzle exit: Mach 1 (choked) velocity static pressure Pressure energy becomes velocity; at Mach 1 the nozzle is choked.
Chapter 19 · The Exhaust System
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The gases travel down the jet pipe and leave through the propelling nozzle, which is a convergent duct. As the area narrows, the gas speeds up, and the energy for that comes from its pressure, so the velocity increases and the pressure decreases. Watch the graph under the engine: velocity climbs and pressure falls through the nozzle. In a turbojet, the gas reaches the local speed of sound, Mach one, at the nozzle at virtually every throttle setting above idle. Notice that Mach one here means the speed of sound in that hot gas, not in the outside air. When the gas at the nozzle is moving at sonic speed, we say the nozzle is choked. Only at low thrust settings is the flow through the nozzle subsonic.
Part 2 · Nozzles
What "choked" means Choked : the gas at the nozzle throat has reached Mach 1 More pressure upstream cannot make it go faster in a convergent nozzle Velocity rises only if the gas temperature rises (e.g. reheat ) Above the critical pressure ratio (about 1.85 ) the gas leaves above ambient pressure That extra pressure gives pressure thrust Jet velocity against nozzle pressure ratio 1 1.5 2 2.5 3 3.5 4 0 200 400 600 800 Nozzle pressure ratio (total pressure ÷ ambient) Jet velocity (m/s) choked at 1.85 convergent: stuck at Mach 1 (543 m/s) C-D nozzle keeps accelerating hotter gas (reheat) Computed for γ = 1.33, gas total temperature 900 K: critical pressure ratio = ((γ + 1) ÷ 2)^(γ ÷ (γ − 1)) = 1.85 sonic jet speed = √(γ R T*) with T* = 2 T0 ÷ (γ + 1) = 773 K Above the critical ratio, extra pressure gives pressure thrust, not speed.
Chapter 19 · The Exhaust System
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look at choking with real numbers. The graph plots jet velocity against the nozzle pressure ratio, the total pressure in the jet pipe divided by the outside pressure, for gas at nine hundred kelvin. At first, more pressure means more velocity. But once the ratio reaches about one point eight five, the gas at the nozzle exit is at Mach one, about five hundred and forty metres per second here, and the blue line goes flat: the nozzle is choked. No further increase in velocity is possible unless the gas temperature is raised, which is what reheat does, shown by the red line, because the speed of sound is higher in hotter gas. Any extra pressure is not wasted, though. The gas leaves above atmospheric pressure, and that pressure difference across the nozzle exit area gives pressure thrust.
Part 2 · Nozzles
The convergent-divergent nozzle Convergent-divergent nozzle throat: Mach 1 subsonic supersonic pressure on the divergent wall has a forward component: extra thrust In supersonic flow a widening duct accelerates the gas. Used with reheat and on supersonic aircraft. Computed along the nozzle (γ = 1.33) inlet throat exit 0.0 0.5 1.0 1.5 2.0 Inlet → throat → exit Mach 1.90 static p ÷ total p static T ÷ total T Mach Exit area 1.6 × throat: Mach rises to 1.90, pressure keeps falling
Chapter 19 · The Exhaust System
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
A convergent-divergent nozzle uses the extra pressure to make extra velocity. In the convergent section, the gas speeds up and its static pressure falls, as before, until it reaches the local speed of sound, Mach one, at the narrowest point, the throat. Now something surprising happens. Once the flow is supersonic, a widening duct makes it go faster still, the opposite of subsonic flow. So in the divergent section the gas keeps accelerating towards the exit, while its pressure and temperature keep falling. In this computed example, an exit area one point six times the throat area takes the gas to about Mach one point nine. The reaction to this increase in momentum is a pressure force on the inside wall of the divergent section, and its component along the axis gives the extra thrust.
Part 2 · Nozzles
Gas changes in convergent and C-D nozzles Section Flow Velocity Static pressure Static temperature Convergent duct Subsonic Increases Decreases Decreases Throat of a choked nozzle Mach 1 (local) Sonic: limit for a convergent nozzle About 1 ÷ 1.85 of total pressure About 86 % of total temperature Divergent duct Supersonic Increases furtherDecreases further Decreases further Divergent duct Subsonic Decreases (diffuser) Increases Increases Jet pipe behind the cone Subsonic, about M 0.5 Held low Little change Little change
Rule: subsonic gas speeds up in a converging duct; supersonic gas speeds up in a diverging duct.
Chapter 19 · The Exhaust System
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the gas changes side by side. In a convergent duct with subsonic flow, the velocity increases while the static pressure and temperature fall. At the throat of a choked nozzle the gas is at Mach one; for our exhaust gas the static pressure there is about the total pressure divided by one point eight five, and the static temperature about eighty-six per cent of the total temperature. In a divergent duct, what happens depends on the speed. With supersonic flow, the velocity increases further and the pressure and temperature keep falling; that is the C-D nozzle. With subsonic flow, a divergent duct does the opposite: it slows the gas and raises its pressure, like the volume behind the exhaust cone, or a diffuser. Remember the rule in the caption; it explains every row.
Part 2 · Nozzles
The exhaust on the whole-engine graph Gas properties from intake (1) to propelling nozzle (8) Pressure Temperature Velocity 1 2 3 4 4.5 5 8 exhaust unit (each curve scaled to its own maximum)
Chapter 19 · The Exhaust System
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us place the exhaust on the graph of the whole engine. Look at the stations along the top: five is the turbine exit and eight is the propelling nozzle. Between them is the exhaust unit. The pressure, already much reduced by the turbines, falls further through the nozzle as it is turned into velocity. The temperature also falls a little through the nozzle, but the gas still leaves hot, and that hot jet is a large part of the energy a turbojet throws away. The velocity, after the gentle slowing behind the exhaust cone, climbs steeply through the nozzle to its highest value anywhere in the engine. That fast jet is what makes the thrust of a pure turbojet, and, as we will see, most of its noise.
Part 3 · By-pass exhausts
Low by-pass engines: the mixer A by-pass engine has two gas streams to discharge: cold by-pass air and hot core gas Low by-pass engines combine them in a mixer unit The mixer gives thorough mixing before the gas leaves One common propelling nozzle Mixing lowers the peak jet velocity: a little better efficiency and less noise Low by-pass: forced mixer hot core cold by-pass air Mixer unit: hot and cold streams thoroughly mixed inside the engine, then leave through one nozzle mixed
Chapter 19 · The Exhaust System
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
A by-pass engine has two gas streams to pass to atmosphere, the cold by-pass air from the fan and the hot gas from the core, which makes its exhaust a little more complicated. In a low by-pass engine, the two streams are brought together inside the engine in a mixer unit. The mixer, often shaped with lobes or chutes, interleaves the hot and cold streams so that they are thoroughly mixed before they are ejected to atmosphere through a single, common propelling nozzle. Mixing evens out the velocity across the jet, lowering the peak velocity, which brings a small gain in propulsive efficiency and a useful reduction in noise. The long outer cowl that runs right back to the common nozzle is the tell-tale sign of a mixed exhaust.
Part 3 · By-pass exhausts
High by-pass engines: two nozzles or one Separate co-axial nozzles: external mixing cold fan air hot core gas streams mix outside, downstream of the turbines Common (integrated) nozzle: partial internal mixing cold fan air hot core gas partial mixing The common nozzle is more efficient; the separate nozzle is lighter and simpler. Separate nozzles: the streams mix externally, downstream of the turbines . A common nozzle partly mixes them first and gives greater efficiency .
Chapter 19 · The Exhaust System
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
High by-pass engines handle their two streams in one of two ways. The standard method is a pair of co-axial nozzles: the cold fan air leaves through the fan nozzle at the end of a short cowl, and the hot core gas leaves through its own nozzle behind it, on the same axis. The two streams then mix externally, in the air behind the engine. So if you are asked where the hot and cold flows mix in a high by-pass turbofan, the answer is downstream of the turbines, outside the engine, not in the bypass duct or the combustion chamber. The alternative is an integrated, or common, exhaust nozzle at the end of a long cowl, in which the two flows are partially mixed before they leave. That gives greater efficiency, at the cost of a longer, heavier nacelle.
Part 3 · By-pass exhausts
Inlet and exhaust danger areas A running engine has two danger zones on the ground Intake : strong suction ahead of and around the intake can draw in people, caps, tools and debrisExhaust : hot, high-velocity gas far behind the engine; blast can blow over people and vehiclesBoth zones grow with thrust : far larger at take-off power than at idle Actual distances are in the aircraft manuals; keep clear and use a marshaller Danger areas round a running engine engine Intake suction zone people, tools, debris drawn in hot, fast exhaust Exhaust wake: blast and heat extends far behind grows a great deal at take-off power Keep clear of both zones; distances depend on type and thrust setting.
Chapter 19 · The Exhaust System
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
A running jet engine is dangerous on the ground at both ends. In front, the intake sucks in a huge mass of air, and the suction zone ahead of and around the intake is strong enough to pull in people, loose clothing, caps, tools and debris, causing injury and foreign object damage. Behind, the exhaust wake of hot, high-velocity gas stretches a long way back and spreads out, strong enough to blow people over, damage vehicles and lift stones. Both zones grow a great deal as thrust increases, so they are much larger at take-off power than at idle. The exact distances depend on the engine type and power setting and are given in the aircraft documents. The rule for everyone on the ramp is simple: keep well clear of both zones.
Part 4 · Noise
Where engine noise comes from Aircraft noise is a mix of sources, but the engine is the main one Engine sources: the compressor (the fan in a high by-pass engine), the turbine and the exhaust All three increase with greater relative airflow velocity Exhaust noise is the most sensitive to velocitySo cutting jet velocity reduces noise most The three main engine noise sources fan / compressor turbine jet All three grow with greater relative airflow velocity . Jet noise is the most sensitive to velocity: cut the jet velocity and the noise falls faster than for the same cut in fan or turbine speed.
Chapter 19 · The Exhaust System
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Airport rules and noise certification limit how much noise aircraft may make, and the engine is the principal source. Within the engine there are three main sources: the compressor, which in a high by-pass engine means mainly the fan; the turbine; and the exhaust jet. Each makes noise in its own way, but they all have one thing in common: the noise increases with greater relative airflow velocity. The exhaust is affected much more strongly than the other two. A given reduction in jet velocity cuts noise far more than the same reduction in compressor or turbine speed. That single fact explains why the industry moved to by-pass engines, which move more air at a lower jet velocity.
Part 4 · Noise
Jet noise: shear, eddies and the eighth power Noise pattern of a jet exhaust nozzle jet core mixing region: small eddies HIGH-frequency noise downstream: large eddies LOW-frequency noise Shear between the fast jet and still air gives violent turbulent mixing. Jet mixing noise ∝ (jet velocity)⁸ 0.5 0.6 0.7 0.8 0.9 1.0 -25 -20 -15 -10 -5 0 Jet velocity (fraction of original) Change in jet noise (dB) -8 dB -24 dB 20 % slower jet: about 8 dB quieter; half the velocity: about 24 dB
Chapter 19 · The Exhaust System
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where does jet noise come from? The jet leaves the nozzle much faster than the still air around it, and the speed difference creates a violent shearing action and extremely turbulent mixing at the edge of the jet. Close to the nozzle the mixing region is thin and full of small eddies, which produce high-frequency noise. Further downstream the eddies grow large and produce low-frequency noise. In a pure jet engine this exhaust noise is so loud that compressor and turbine noise hardly matter, except at very low thrust. The graph on the right shows why velocity matters so much: jet mixing noise rises roughly with the eighth power of jet velocity. A jet twenty per cent slower is about eight decibels quieter, and halving the velocity removes about twenty-four decibels.
Part 4 · Noise
How the noise picture changes with by-pass ratio Engine Jet velocity Dominant noise Why Pure turbojet Very high Exhaust jet (compressor and turbine insignificant except at very low thrust)Jet noise rises steeply with velocity Low by-pass Lower Jet still important; turbine and LP compressor louder They now handle much more power High by-pass (about 5 : 1)Low Fan and turbine predominateJet noise has fallen so far that the others show through Next step — Treat the fan and turbine Acoustic linings in the intake, by-pass duct and hot zones
A high by-pass engine is much quieter than a turbojet of the same thrust; what noise remains comes mainly from the fan and the turbine.
Chapter 19 · The Exhaust System
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us see how the noise picture changes as the by-pass ratio grows. In a pure turbojet, the jet is so fast that exhaust noise swamps everything; compressor and turbine noise only show through at very low thrust. In a by-pass engine, the jet velocity is lower, so exhaust noise drops, but the turbines and the low-pressure compressor are handling much greater power, so they generate more noise. In a high by-pass engine, with a ratio of about five to one, jet noise has fallen so far that the fan and the turbine become the predominant sources. So a high by-pass engine is far quieter overall than a turbojet of similar power, and the noise it does make is created mainly by the fan and the turbine. Logically, manufacturers then turned their attention to those two.
Part 4 · Noise
Acoustic linings Noise-absorbing material lines the intake and the by-pass duct Very effective at cutting fan noise Further back, in the hotter zones , slightly different materials are used Typical lining: perforated face sheet, honeycomb cells, solid backing Penalty: a little extra weight and skin friction , so slightly higher fuel consumption Acoustic lining: how it works perforated face sheet (towards the airflow) solid backing sheet honeycomb cells between sound waves Where the linings go intake by-pass duct hot zones Cost: a little extra weight and skin friction, so slightly higher fuel consumption.
Chapter 19 · The Exhaust System
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Once jet noise had been tamed, attention turned to the fan and turbine, and the main weapon is the acoustic lining. Noise-absorbing material is fitted round the inside of the engine intake and the by-pass duct, where it is extremely effective at cutting fan noise. Further down the engine, in the hotter zones, slightly different materials are used to do the same job. A typical lining is a sandwich: a perforated face sheet towards the airflow, a layer of honeycomb cells behind it, and a solid backing sheet. Sound waves pass through the holes into the cells, where much of their energy is dissipated. There is a small price. The linings add a little weight, and their surface has slightly higher skin friction, so together they cause a slight increase in fuel consumption.
Part 4 · Noise
Silencing older turbojets Older pure turbojets could not simply be given linings and a big fan Lobe-type nozzles split the jet into several smaller jetsThese mix rapidly with slower air trapped by the lobes , so less mixing noise Corrugated internal mixers were the most effective at reducing noiseBut they brought performance penalties , so operators did not like them Lobe-type nozzle seen from behind blue: slower air trapped between the lobes hot jet split into lobes Separate small jets mix quickly with slower air: less jet noise Corrugated internal mixer: most effective, but a performance penalty Fitted to older pure turbojets; modern engines use linings and high by-pass
Chapter 19 · The Exhaust System
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Modern engines benefit from high by-pass ratios and acoustic linings, but aircraft fitted with older pure turbojets needed another answer, and you may still see the hardware on older types. One device is the lobe-type nozzle. Its outlet is shaped into a number of lobes, so the jet leaves as several separate smaller jets. Slower moving air is trapped between the lobes, and the separate jets mix with it rapidly, which shortens the noisy mixing region and lowers the noise. The other device is the corrugated internal mixer. This was the most efficient at reducing noise, but it also brought performance penalties, extra weight and pressure losses, which limited its popularity with operators. Today the serrated chevron edges on some nozzles carry on the same idea of encouraging gentler mixing.
Summary
What to take into the exam Temperatures Exhaust 550–850 °C, up to 1 500 °C with reheat. Protection: cooling air gap + insulation blanket.
Jet pipe Turbine exit 750–1 250 ft/s ≈ Mach 0.5; held at about M 0.5 to minimise turbulence.
Exhaust cone Annulus divergent: slows the gas; keeps hot gas off the rear turbine disc face; carries the rear bearing.
Struts Rear support struts with fairings straighten out residual whirl.
Nozzle Convergent: velocity up, pressure down. Choked at Mach 1; more velocity only with more heat.
C-D nozzle Sonic at the throat, supersonic in the divergent part; wall pressure gives extra thrust.
By-pass Low BPR: mixer unit. High BPR: co-axial nozzles, mixing downstream of the turbines; common nozzle more efficient.
Noise Jet noise ∝ V⁸. Turbojet: exhaust dominates. High BPR: fan and turbine predominate. Linings, lobes, mixers.
Chapter 19 · The Exhaust System
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up the exhaust system. Gas enters it at five hundred and fifty to eight hundred and fifty degrees, up to one thousand five hundred with reheat, and the airframe is protected by a cooling air gap plus an insulating blanket. The gas leaves the turbine at about Mach nought point five and is held there in the jet pipe to minimise turbulence. The exhaust cone makes the space behind the turbine divergent, slowing the gas, and keeps hot gas off the turbine disc; the struts straighten residual whirl. The convergent nozzle speeds the gas up and lowers its pressure, and when the flow reaches Mach one it is choked. A C-D nozzle goes supersonic and gains thrust from the divergent wall. Low by-pass engines mix their streams; high by-pass streams mix behind the engine. And for noise, jet velocity is king.