Engines · Chapter 24
Gearboxes and Accessory Drives How a gas turbine drives its pumps, generators and starter: the drive from the HP shaft, coping with shaft expansion, high and low speed gearboxes, and the shear neck.
HP shaft → radial shaft → accessory gearbox → pumps, generators, starter ACCESSORY DRIVES © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the chapter on gearboxes and accessory drives. A gas turbine does far more than make thrust. It must also drive its own fuel and oil pumps, and the aircraft’s hydraulic pumps and generators, and at start-up it is itself driven by a starter. All of that power passes through a set of gears and shafts that take a drive from deep inside the engine out to a gearbox on the casing. In this lesson we will follow that drive from the HP shaft to the accessories, see how designers stop the gears coming apart as the shaft expands, and meet the shear neck, a mechanical fuse.
Roadmap
From the HP shaft to the accessories 1 · The job What the accessory gearbox drives, and why the drive comes from the HP shaft .
2 · The drive train Internal gearbox, radial shaft , transfer gearbox, external gearbox.
3 · Shaft growth Stub shaft and idler gear drives keep the gears in mesh.
4 · Layout High and low speed gearboxes, tooth widths, the oil pump pack , hand turning.
5 · Protection The shear neck : a mechanical fuse, and where it is never fitted.
6 · The cost Power taken off the shaft costs fuel: SFC rises .
7 · Generators Why an engine-driven generator needs a constant-speed drive .
8 · Exam Traps, a summary, and practice questions.
Chapter 24 · Gearboxes and Accessory Drives
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this lesson. First, the job of the accessory gearbox and why its drive is always taken from the high pressure shaft. Then we follow the drive train itself: the internal gearbox, the radial shaft, the transfer gearbox and the external gearbox. Third, a real engineering problem: the compressor shaft grows as it heats up, and we will see the two ways of keeping the gears in mesh. Fourth, the layout of the gearboxes, including engines with two gearboxes, the oil pump pack and hand turning. Fifth, protection by the shear neck. Sixth, the price of all this: every kilowatt you take off the shaft costs fuel. And finally a word on generators and constant-speed drives, then the exam traps and a summary.
Part 1 · The job
What the accessory gearbox is for The accessory gearbox (AGB) takes a small share of engine power to drive engine and aircraft accessories Engine accessories: fuel pumps and fuel control, oil pressure and scavenge pumps , speed sensors (tacho-generator) Aircraft accessories: hydraulic pumps and electrical generators ; pneumatic power comes from bleed air instead The starter is mounted on it too, and drives the engine through it Gives every accessory a mounting pad and its own speed through gear ratios
HP shaft: the power source Accessory gearbox (AGB) Fuel pumps + fuel control Oil pressure + scavenge pumps Hydraulic pump Generator (IDG) Speed sensor / tacho Starter motor
Chapter 24 · Gearboxes and Accessory Drives
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The accessory gearbox, often called the A G B, takes a small share of the engine’s power and uses it to drive the accessories. Some of those are the engine’s own: the fuel pumps and fuel control, the oil pressure and scavenge pumps, and speed sensors such as the tacho-generator that feeds the rev counter. Others serve the aircraft: hydraulic pumps and electrical generators. Pneumatic power for the aircraft is normally taken as bleed air from the compressor rather than through the gearbox. In most engines the starter motor is also mounted on the gearbox, and at start-up the power flows the other way, from the starter through the gears into the engine. The gearbox gives each accessory a mounting pad and, through its gear ratios, the right speed to run at.
Part 1 · The job
Typical accessories on the gearbox Accessory Serves Why it needs the drive HP fuel pump and fuel control unit Engine Fuel at high pressure to the spray nozzles, metered to the demand Oil pump pack Engine One pressure pump and several scavenge pumps for the bearings and gears Tacho-generator / speed sensor Engine Signals N2 to the rev counter and to the engine control Centrifugal breather (de-oiler) Engine Spins oil mist out of the vent air before it leaves the engine Hydraulic pump(s) Aircraft Engine-driven pumps for flying controls, gear, brakes Generator (often an IDG) Aircraft AC electrical power; needs a constant speed Starter motor Engine Turns the HP spool for starting, then disengages
The exact list varies by engine, but the pattern is the same: the essentials for running the engine, plus hydraulic and electrical power for the aircraft.
Chapter 24 · Gearboxes and Accessory Drives
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table lists the typical accessories. The high pressure fuel pump and the fuel control unit deliver fuel to the burners and meter it. The oil pump pack holds one pressure pump and several scavenge pumps. A tacho-generator or speed sensor signals the H P spool speed, N two, to the gauge and the engine control. A centrifugal breather, sometimes called a de-oiler, spins oil droplets out of the vent air so that oil is not thrown overboard. Those all belong to the engine. For the aircraft there are hydraulic pumps, and the generator, which on airliners is often an integrated drive generator. And then the starter motor, which drives the engine for starting and then disengages. Remember the split between engine and aircraft accessories: it comes back later when we talk about two gearboxes.
Part 1 · The source
Why the drive comes from the HP shaft The drive is taken from the HP compressor shaft , at the cold front end of the HP spool The starter turns the HP spool , so pumps and the fuel control work from the first turn The HP spool runs fastest : the same power needs less torque , so lighter gears and shafts Not from the hot end : heat losses would be high and the shafts would need exotic materials Typical power through the bevel gears: 400 to 500 hp
HP spool (N2): bronze LP spool (N1) Starter turns it first accessories work from the start Runs fastest less torque for the same power Cold end of the core drive near the compressor, not the turbine
Chapter 24 · Gearboxes and Accessory Drives
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
The drive for the accessory gearbox is taken from the high pressure compressor shaft, at the cold front end of the H P spool. There are three good reasons. First, the starter motor turns the H P spool, so if the accessories hang off that same shaft, the fuel pump, the fuel control and the oil pumps all work from the very first turn of a start. Second, the H P spool runs at the highest speed, and for a given power a faster shaft carries less torque, so gears and shafts can be lighter. Third, taking the drive from the hot end, near the turbines, would bring heavy heat losses and would need shafts of exotic materials. The power passing through those bevel gears is large: of the order of four hundred to five hundred horsepower.
Part 2 · The drive train
Internal gearbox, radial shaft, transfer gearbox, external gearbox
1 2 3 4 1 Internal gearbox bevel gears on the front of the HP shaft 2 Radial (tower) drive shaft out through a hollow strut and the bypass 3 Transfer gearbox turns the drive through an angle 4 External accessory gearbox a pad and a speed for every accessory Taken at the cold front end of the HP spool
Chapter 24 · Gearboxes and Accessory Drives
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the power step by step. Inside the engine, at the front of the H P shaft, a pair of bevel gears forms the internal gearbox. The bevel gears turn the drive through a right angle into the radial drive shaft, sometimes called the tower shaft, which runs outwards through a hollow strut in the compressor casing. On a large turbofan it must also cross the bypass duct. At the outside, a small transfer gearbox turns the drive again, through another angle, and a short horizontal shaft takes it into the external accessory gearbox. That external gearbox carries the mounting pads for the fuel pump, the oil pumps, the hydraulic pump, the generator and the starter, each geared to its own speed. On high bypass engines the gearbox is usually tucked under the fan case or the core, inside the cowlings.
Part 2 · Installation
Where the gearbox fits on different engines
no drive from the hot turbine end room inside the cowling gearbox underneath, easy to service Large turbofans The engine is so big that even large accessories fit inside the cowling . The hard part is getting the drive out from the HP shaft, through the core and bypass duct.
Not from the hot end A drive from the turbine end would suffer high losses and need exotic materials for hot shafts and bearings.
Underneath, for servicing The external gearbox is usually under the engine , curved to the casing, where engineers can reach it easily.
Chapter 24 · Gearboxes and Accessory Drives
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Where the gearbox goes depends on the engine. On a modern large turbofan there is plenty of room: the engine is so big that even the largest accessories fit inside the cowling around the fan case or the core. The real difficulty is getting a drive shaft out from the H P shaft, through the compressor casing and across the bypass duct, without spoiling the airflow. That is why the radial shaft runs inside a streamlined strut. Designers avoid taking the drive from the hot end of the engine, because the losses would be high and the shafts and bearings would need exotic heat-resistant materials. And the external gearbox is usually placed underneath the engine, curved to follow the casing, so that engineers can reach the accessories easily for servicing.
Part 2 · Worked example
Why a fast drive shaft is a light drive shaft Power = torque × rotational speed 300 kW (about 400 hp) at 12 000 rpm : torque ≈ 239 N m Same power at 4 000 rpm : torque ≈ 716 N m , three times as much Torque sets the size of gear teeth and shafts, so faster = lighter One more reason to drive the accessories from the fast HP spool Same power, two shaft speeds
0
200
400
600
800
Torque (N m) 239 N m 12,000 rpm 716 N m 4,000 rpm Power = torque × rotational speed 300 kW (≈ 400 hp) carried by the drive 3 times slower shaft → 3 times the torque
Chapter 24 · Gearboxes and Accessory Drives
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a worked example that shows why speed matters. Power equals torque multiplied by rotational speed. Suppose the drive must carry three hundred kilowatts, which is about four hundred horsepower. At twelve thousand r p m, a typical H P shaft speed, the torque works out at about two hundred and thirty nine newton metres. Carry the same power at four thousand r p m, more like an L P shaft, and the torque is about seven hundred and sixteen newton metres, three times as much. It is torque, not power, that sets the size of gear teeth, splines and shafts. So a drive taken from a fast shaft can be smaller and lighter. That is one more reason for driving the accessories from the high speed spool.
Part 3 · The problem
The compressor shaft grows as it heats The compressor shaft expands and contracts axially as the engine heats and cools A bevel gear fixed to it would move away from its partner on the radial shaft The teeth would pull apart and the drive would be interrupted A momentary loss of a 400 to 500 hp drive would wreck the bevel teeth So the gears must stay meshed whatever the shaft does Cold: gears in full mesh HP compressor shaft radial shaft Hot: shaft grows, teeth pull apart HP compressor shaft radial shaft axial growth gap: drive lost
Chapter 24 · Gearboxes and Accessory Drives
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a real engineering problem. The compressor shaft is long, and as the engine heats up during each run it expands, then contracts again as it cools. Some axial movement of the shaft is unavoidable. Now imagine a bevel gear fixed directly onto that shaft, meshing with a bevel gear on the radial shaft, which is held in place by the casing. Watch what happens as the shaft heats and expands: the gear on the shaft moves away and the teeth start to pull apart. The drive would be interrupted. Even a momentary interruption of a drive carrying four or five hundred horsepower, followed by the teeth crashing back together, would cause massive damage and probably destroy the gears. So the gears must be arranged to stay meshed, whatever the shaft does. There are two common solutions.
Part 3 · Solution 1
The stub shaft drive The compressor shaft is splined : grooves cut parallel to its axis A stub shaft with matching internal teeth fits around the splines A location bearing holds the stub shaft firmly in position The compressor shaft slides through the splines; the stub shaft does not move The bevel gear on the stub shaft stays in mesh with the radial shaft Stub shaft on splines compressor shaft (splined) location bearing (fixed to the casing) radial drive shaft shaft slides freely inside the splines The stub shaft and its bevel gear never move axially, so the bevel teeth stay in mesh.
Chapter 24 · Gearboxes and Accessory Drives
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The first solution is the stub shaft drive. The compressor shaft is splined, which means it has grooves cut along it, parallel to its axis. A short stub shaft, with teeth cut on the inside to match those grooves, fits around the splined section. A location bearing, fixed to the casing, holds the stub shaft firmly in position, and the bevel gear is on the stub shaft, not on the compressor shaft. The splines transmit the turning effort, but they let the compressor shaft slide axially through the stub shaft. Watch the compressor shaft: as it slides with expansion and contracts again, the stub shaft stays exactly where it is, and its bevel gear stays fully in mesh with the gear on the radial shaft.
Part 3 · Solution 2
The idler gear drive An idler gear shaft is held firmly by location bearings One end carries a wide-toothed spur gear A narrower spur gear on the compressor shaft meshes with it and slides along it The other end carries a bevel gear that drives the radial shaft Axial movement of the compressor shaft is absorbed by the wide teeth Idler gear with a wide spur gear compressor shaft narrow spur gear moves with the shaft idler shaft wide spur gear location bearings radial shaft The narrow gear slides along the wide one and stays in mesh; the idler shaft and its bevel gear never move axially.
Chapter 24 · Gearboxes and Accessory Drives
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The second solution uses an idler gear. A separate idler shaft runs alongside, held firmly in place by location bearings so it cannot move axially. At one end it carries a wide-toothed spur gear. A narrower spur gear on the compressor shaft meshes with it. Because spur gear teeth are straight and parallel to the shaft, the narrow gear can slide along the wide one and stay engaged. Watch the compressor shaft slide as it expands and then come back: the narrow gear simply moves along the face of the wide gear. At the other end of the idler shaft is a bevel gear, meshing with the gear on the radial drive shaft. Since the idler shaft never moves, that bevel pair always stays correctly in mesh.
Part 3 · Side by side
Stub shaft and idler gear compared Stub shaft drive Idler gear drive What takes up the movement Splines between compressor shaft and stub shaftWide spur gear on the idler shaftWhat is held still Stub shaft, by a location bearing Idler shaft, by location bearings Where the bevel gear sits On the stub shaft On the far end of the idler shaft Extra parts Stub shaft and bearing Idler shaft, two spur gears, bearings Common aim Bevel teeth never pull apart Bevel teeth never pull apart
Both methods separate the part that moves (the compressor shaft) from the part that must not (the bevel gear driving the radial shaft).
Chapter 24 · Gearboxes and Accessory Drives
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us compare the two methods side by side. In the stub shaft drive, splines take up the movement: the compressor shaft slides inside the stub shaft, and a location bearing holds the stub shaft still, with the bevel gear on it. In the idler gear drive, a wide spur gear takes up the movement: the narrow gear on the compressor shaft slides along it, while location bearings hold the idler shaft still, with the bevel gear at its far end. The idler method needs a few more parts. But the principle is the same in both: separate the part that moves, which is the compressor shaft, from the part that must not move, which is the bevel gear driving the radial shaft. That way the bevel teeth never pull apart.
Part 4 · Spreading the load
High speed and low speed gearboxes
Low speed gearbox driven from the LP shaft aircraft accessories High speed gearbox driven from the HP shaft starter, oil and fuel pumps Why two? spreads the drive load two smaller groups of accessories fit the limited space better The high speed gearbox is driven by the HP shaft; the low speed gearbox by the slower LP shaft.
Chapter 24 · Gearboxes and Accessory Drives
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Some engines spread the load of driving the accessories between two gearboxes. A second radial shaft is taken from the low pressure compressor shaft, which turns more slowly, and it drives a second external gearbox. This has a second advantage: the accessories are split into two smaller groups, which are easier to fit into the limited space around the engine. The gearbox driven from the H P shaft is called the high speed external gearbox, because its shaft turns fastest of all. The other one, driven from the L P shaft, is naturally called the low speed external gearbox. In the next slide we will see which accessories go on which.
Part 4 · Which goes where
Engine accessories go on the HP gearbox On start-up the starter turns the HP shaft first The LP spool only begins to turn once gas flows through its turbine So oil pumps and fuel pumps , which the engine needs at once, go on the HP (high speed) gearbox The starter itself is on the HP gearbox too Aircraft accessories can go on the LP (low speed) gearbox During a start
0
20
40
60
0
20
40
60
Time from start selection (s)
Speed (% of max) N2 (HP) N1 (LP) The starter drives the HP spool; the LP spool only follows once gas flow reaches its turbine.
Chapter 24 · Gearboxes and Accessory Drives
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Which accessories go on which gearbox? Think about a start. The starter motor turns the H P shaft first. The L P spool only begins to turn when air and then hot gas flow through its turbine, so it lags well behind; at idle you might have about sixty per cent N two but only about twenty five per cent N one. The engine needs oil pressure and fuel from the very first moments of a start, so the engine-specific accessories, the oil pumps and the fuel pumps, are grouped on the gearbox driven by the H P shaft, the high speed gearbox. The starter is mounted there too. Accessories that serve the aircraft rather than the engine itself can then go on the low speed gearbox.
Part 4 · The external gearbox
Inside a banana-shaped external gearbox Hand turning drive pad Speed sensor Oil pump pack Fuel pumps Radial drive in Breather (de-oiler) Starter Hydraulic pump Generator (IDG) Gear tooth width: narrow teeth = light accessories wide teeth = the heavy loads External gearbox (seen from below, curved to fit round the engine) Curved to fit around the engine and usually underneath for servicing. Wider gear teeth carry bigger loads.
Chapter 24 · Gearboxes and Accessory Drives
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a typical external gearbox. Because it has to fit around the engine casing, it is curved, often described as banana-shaped, and it usually sits underneath the engine where it is easy to service. Inside, a train of gears runs from the radial drive input to each accessory pad. Above the gears you can see the accessories: a hand-turning drive, the speed sensor, the oil pump pack, the fuel pumps, the breather, the starter, the hydraulic pump and the generator. Now look at the tooth widths along the bottom. The gears serving the heavy loads, like the generator and the hydraulic pump, have wide teeth; the gears driving small accessories have thin teeth. Matching each gear to its load gives an efficient spread of the drives for the minimum weight.
Part 4 · Oil pump pack
One pressure pump, several scavenge pumps The oil pumps are grouped in an oil pump pack on the gearbox It holds one pressure pump And several scavenge pumps : as many as six on some engines Each scavenge pump empties a bearing chamber or the gearbox back to the tank Total scavenge capacity exceeds pressure capacity, so chambers never flood Oil pump pack: one drive common drive shaft from the gearbox Pressure to bearings Scavenge Scavenge Scavenge from bearing chambers and gearbox Up to six scavenge pumps on some engines: scavenge capacity is greater than pressure capacity
Chapter 24 · Gearboxes and Accessory Drives
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil pumps are not separate units scattered over the gearbox; they are grouped in an oil pump pack, all turned by one drive. The pack contains one pressure pump, which sends oil out to the bearings and gears, and several scavenge pumps, as many as six on some engines. Each scavenge pump draws oil back from one bearing chamber or from the gearbox itself and returns it to the tank. Why so many scavenge pumps? The returning oil is foamy and mixed with air, so it takes up more volume, and every chamber must be emptied separately. So the total scavenge capacity is always greater than the pressure pump capacity, which makes sure that no bearing chamber ever floods with oil.
Part 4 · Hand turning
Hand turning the engine for inspection The gearbox has an engine hand-turning drive pad A tool on the pad turns the HP rotor back through the drive train Used on the ground with the engine stopped Lets an engineer inspect each blade through borescope ports Works because the gears drive in both directions HP compressor (casing cut away) borescope view drive runs backwards up to the HP rotor hand-turning tool on the drive pad Engine stopped, on the ground: each blade is turned into view in turn.
Chapter 24 · Gearboxes and Accessory Drives
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The external gearbox has one more useful feature: an engine hand-turning access. This is a drive pad where an engineer can fit a hand tool on the ground with the engine stopped. Because gears transmit drive in both directions, turning the tool turns the gearbox, the radial shaft, the bevel gears and so the whole H P rotor, slowly and smoothly. Meanwhile a borescope, a thin optical probe, is pushed in through an inspection port in the casing. By turning the rotor step by step, the engineer can look at every compressor or turbine blade in turn for nicks, cracks or burning, without taking the engine apart. It is a simple idea that saves an enormous amount of maintenance time.
Part 5 · Protection
The shear neck: a mechanical fuse A seized accessory could wreck the whole gearbox and so lose the engine A shear neck is a weak section machined into the accessory’s drive shaft It fails at about 25% above the normal maximum load of that drive Only the faulty accessory loses its drive; the rest keep working Like an electrical fuse , it sacrifices itself to protect the system gearbox Accessory (e.g. hydraulic pump) Shear neck deliberately weak section Breaks at about 125% of the drive’s normal maximum torque A seized accessory loses its drive; the gearbox and every other accessory keep running, like a fuse in a circuit. Not fitted to oil pumps or the HP fuel pump.
Chapter 24 · Gearboxes and Accessory Drives
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
What if an accessory seizes? A hydraulic pump with a failed bearing, for example, could lock up, and the gear driving it would try to keep turning it. The overload could strip the teeth and destroy the whole gearbox, and with it the oil and fuel pumps, so the engine would be lost. To prevent that, many accessory drives include the mechanical equivalent of an electrical fuse, the shear neck. It is a weak section deliberately machined into the drive shaft. It is designed to fail at a load perhaps twenty five per cent above the normal maximum for that accessory. Watch the accessory seize: the shear neck breaks, that one accessory loses its drive, and the gearbox and all the other accessories keep running normally.
Part 5 · Worked example
Sizing a shear neck, and where it is never fitted Hydraulic pump drive, normal maximum torque 60 N m Shear neck designed to fail at 60 × 1.25 = 75 N m A seizing pump demanding 95 N m breaks the neck , not the gears Not fitted to primary engine accessories: oil pumps and HP fuel pump If those fail the engine must be shut down anyway: nothing to save Worked example
0
25
50
75
100
Drive torque (N m) 60 normal max 75 neck breaks 95 seized pump 60 N m × 1.25 = 75 N m Any demand above 75 N m snaps the neck before the gear teeth can be damaged.
Chapter 24 · Gearboxes and Accessory Drives
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us size one. Suppose a hydraulic pump drive normally carries up to sixty newton metres of torque. A shear neck twenty five per cent stronger than that fails at sixty times one point two five, which is seventy five newton metres. If the pump seizes and its drive demands, say, ninety five newton metres, the neck snaps long before the gear teeth suffer. Now the exam point: shear necks are not used on the drives of the primary engine accessories, the oil pumps and the high pressure fuel pump. Why not? Because if one of those fails, the engine has to be shut down immediately anyway. There is nothing to be gained by letting the engine carry on, and you certainly do not want a fuel or oil pump drive to break from a mere overload.
Part 6 · The cost
Power off-take raises specific fuel consumption Every accessory absorbs shaft power from the HP spool For the same thrust the engine must burn more fuel So adding an accessory (e.g. another hydraulic pump) increases SFC Example: 100 kW off-take at cruise ≈ +24 kg/h fuel, about +1.6% SFC Bleed air for the aircraft has the same effect Cost of shaft power at cruise
0
100
200
300
0
1
2
3
4
5
Extra power taken off the HP shaft (kW)
Increase in SFC (%) 100 kW → +1.6% Cruise thrust 25 kN, fuel flow about 1530 kg/h; 100 kW of shaft power costs about 24 kg of fuel per hour
Chapter 24 · Gearboxes and Accessory Drives
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Nothing comes for free. Every accessory on the gearbox absorbs shaft power from the H P spool, and that power has to come from burning fuel. To keep the same thrust, the fuel control must supply a little more fuel, so the specific fuel consumption, the fuel burned per unit of thrust, goes up. That is the exam answer: modifying an engine to drive one more hydraulic pump increases the S F C. Here are some rough numbers. At a cruise thrust of twenty five kilonewtons the engine might burn about one thousand five hundred kilograms of fuel an hour. Taking an extra hundred kilowatts off the shaft, with the core turning fuel into shaft work at about thirty five per cent efficiency, costs about twenty four kilograms an hour, an S F C increase of roughly one and a half per cent.
Part 7 · Generators
Why generators need a constant-speed drive AC frequency depends on generator speed ; aircraft systems need a steady 400 Hz A 4-pole generator needs 12 000 rpm for 400 Hz N2 varies from idle to take-off: geared directly, idle at 60% N2 would give only 240 Hz A constant-speed drive (CSD) between gearbox and generator holds the speed CSD and generator in one unit: the integrated drive generator (IDG) Generator frequency vs N2
60
70
80
90
100
200
250
300
350
400
450
HP spool speed N2 (%)
Frequency (Hz) with constant-speed drive: 400 Hz direct drive: 240 Hz at idle 4-pole generator: 400 Hz needs 12 000 rpm N2 changes, so a CSD holds the generator speed
Chapter 24 · Gearboxes and Accessory Drives
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The generator is a special case. The frequency of an A C generator depends directly on how fast it turns, and aircraft systems want a steady four hundred hertz. A four-pole generator gives four hundred hertz at twelve thousand r p m. But the gearbox speed follows N two, which changes all the time between idle and take-off power. If the generator were geared directly, so that it gave four hundred hertz at full N two, then at an idle of sixty per cent it would turn at sixty per cent of the speed and give only two hundred and forty hertz. So between the gearbox and the generator sits a constant-speed drive, which converts the varying input into a constant output speed. When the drive and the generator are combined into one unit it is called an integrated drive generator, or I D G.
Other gearboxes
Reduction gearboxes on turboprops and turboshafts A turboprop needs a reduction gearbox : turbine speeds are far too high for a propeller Usually epicyclic : sun gear on the turbine shaft, planet carrier drives the propeller Example: 15 000 rpm in, 1 200 rpm out, a 12.5 : 1 reduction It carries the full engine power, so it is far bigger than an accessory gearbox Accessories are still driven from a separate accessory gearbox Turboprop reduction gearbox sun gear fixed ring gear planets on a carrier → propeller Turbine shaft drives the sun; the planet carrier turns the propeller e.g. 15 000 rpm in, 1 200 rpm out: a 12.5 : 1 reduction
Chapter 24 · Gearboxes and Accessory Drives
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Do not confuse the accessory gearbox with the reduction gearbox of a turboprop or turboshaft. A gas turbine shaft may turn at well over ten thousand r p m, far too fast for a propeller tip, so the propeller is driven through a reduction gearbox. It is usually epicyclic: the turbine shaft drives a central sun gear, planet gears run round inside a fixed ring gear, and the planet carrier turns the propeller. A typical figure is fifteen thousand r p m in and twelve hundred out, a reduction of twelve and a half to one. Because it carries the full power of the engine, thousands of horsepower, the reduction gearbox is a large, heavy unit. The engine accessories are still driven separately, from an accessory gearbox in the usual way.
Exam traps
Points examiners like to test Drive source Fuel, oil and hydraulic pumps are driven from the HP compressor shaft, not the LP fan or a turbine.
Extra accessory One more pump on the gearbox → SFC increases . Not a change of RPM or EGT as such.
Shear neck Fails at about 125% of the normal max load. Not on oil pumps or the HP fuel pump.
High speed gearbox Driven by the HP shaft; carries the engine accessories and starter.
Expansion Stub shaft on splines , or idler with a wide spur gear , keeps the bevels in mesh.
Pump pack One pressure pump, up to six scavenge pumps.
Chapter 24 · Gearboxes and Accessory Drives
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the points examiners like to test. The fuel, oil and hydraulic pumps are driven from the H P compressor shaft, not from the L P fan or the turbine. Adding an accessory, for example another hydraulic pump, increases the specific fuel consumption; do not be tempted by answers about R P M or exhaust gas temperature. The shear neck fails at about one hundred and twenty five per cent of the normal maximum load and is never fitted to the oil pumps or the H P fuel pump. The high speed gearbox is the one driven by the H P shaft, and it carries the engine accessories and the starter. The stub shaft and idler gear drives both keep the bevel gears in mesh as the shaft expands. And the oil pump pack has one pressure pump and up to six scavenge pumps.
Summary
Gearboxes and accessory drives in one page Purpose Drive fuel, oil and hydraulic pumps, generators and speed sensors; mount the starter.
Source HP compressor shaft, cold end: starter turns it first, fastest, least torque.
Drive train Internal bevel gears → radial shaft in a strut → transfer gearbox → external gearbox.
Expansion Stub shaft on splines with a location bearing, or idler shaft with a wide spur gear.
Two gearboxes High speed (HP): engine accessories and starter. Low speed (LP): spreads the load.
Layout Banana-shaped, underneath; wide teeth for big loads; oil pump pack; hand-turning pad.
Shear neck Weak link failing at ~125% max load; not on oil or HP fuel pump drives.
Cost Power off-take raises SFC; generators need a CSD or IDG for 400 Hz.
Chapter 24 · Gearboxes and Accessory Drives
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us sum up. The accessory gearbox drives the fuel, oil and hydraulic pumps, the generators and the speed sensors, and carries the starter. Its drive is taken from the cold end of the H P compressor shaft, because the starter turns that spool first and it runs fastest, with the least torque. The drive passes through internal bevel gears, a radial shaft in a strut, a transfer gearbox and into the external gearbox. Shaft expansion is handled by a stub shaft on splines or by an idler shaft with a wide spur gear. Some engines add a low speed gearbox driven from the L P shaft, with the engine accessories kept on the high speed one. The gearbox is banana-shaped and underneath, with a pump pack and hand-turning pad. Shear necks protect it, but not on oil or H P fuel pumps. And remember: every kilowatt taken off raises the S F C.