Engines · Chapter 25
Gas Turbine Ignition How a gas turbine is lit: dual high energy ignition, the capacitor discharge unit, igniter plugs, and when continuous and automatic ignition are used.
ANNULAR COMBUSTOR two igniters · high energy · capacitor discharge
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to gas turbine ignition. In a piston engine the spark plugs fire on every power stroke for as long as the engine runs. A gas turbine is different: once its flame is lit it burns continuously, so ignition is needed only to start it, to relight it if the flame goes out, and as a safeguard in bad conditions. But that one job is demanding, so the system is duplicated and delivers a very powerful spark from a capacitor. In this lesson we will see how the high energy ignition unit works, why it can kill, how igniter plugs differ, and when each type of ignition is selected.
Roadmap
Lighting a gas turbine 1 · Why and where Ignition only to light up ; two igniters in the combustor.
2 · How much energy High energy 6–12 J and low energy 3–6 J.
3 · When Start, continuous , automatic and relight selections.
4 · The ignition unit Trembler, transformer, rectifier, capacitor , gap, choke .
5 · Safety Discharge and safety resistors; a lethal unit.
6 · Igniter plugs Air gap and surface discharge types.
7 · Relight Windmill relight and its envelope.
8 · Exam Traps, a summary, and practice questions.
Chapter 25 · Gas Turbine Ignition
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the route through this lesson. First, why a gas turbine needs ignition only to light up, and where the two igniters sit in the combustor. Second, how much energy a spark carries, comparing high energy and low energy ignition. Third, when each type of ignition is selected: for starting, continuously, automatically and for a relight. Fourth, we open up the high energy ignition unit and follow the energy from the twenty eight volt supply through the trembler, transformer, rectifier and capacitor to the discharge gap and choke. Fifth, its safety features, because the unit can kill. Sixth, the two kinds of igniter plug. Seventh, relighting in flight. And finally the exam traps and a summary.
Part 1 · Why
Ignition only to light the flame Combustion in a gas turbine is continuous : once lit, the flame sustains itself So ignition is needed only for starting and for relighting after a flame-out And as a precaution where flame-out is a risk: heavy rain, contaminated runways Every gas turbine has a dual ignition system All use high energy ignition units for starting Piston engine a spark for every power stroke, all the time Gas turbine sparks only to light up continuous flame: self-sustaining Combustion in a gas turbine is continuous, so after light-up the igniters are switched off. They are used again only to relight, or as a precaution against flame-out.
Chapter 25 · Gas Turbine Ignition
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Ignition in a gas turbine has a very different job from the spark plugs in a piston engine. A piston engine burns its charge in separate bursts, so it needs a spark for every power stroke, for as long as it runs. A gas turbine burns fuel continuously. Once the flame in the combustion chamber is alight, it keeps itself going, and the igniters can be switched off. So ignition is needed to start the engine, to relight it if the flame goes out in flight, and as a precaution whenever there is a risk of flame-out, for example in heavy rain or on a contaminated runway. Because a reliable light-up is so important, every gas turbine has a dual ignition system, and all of them use high energy ignition units for starting.
Part 1 · Where
Two igniters in the combustion chamber Two igniter plugs, each fed by its own ignition unit Placed near a fuel spray nozzle , usually low in the combustor The plug tip sits just inside the flame tube wall, cooled by air Annular combustor: the flame spreads round the ring Can or can-annular: igniters in two cans; flame spreads by interconnectors Igniter 1 Igniter 2 looking aft at the combustor fuel spray nozzles Two igniters, low in the combustor, each beside a spray nozzle
Chapter 25 · Gas Turbine Ignition
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every engine has two igniter plugs, and each one is fed by its own ignition unit, so a single failure cannot prevent a start. The plugs are fitted through the outer casing so that their tips sit just inside the wall of the flame tube, where they are cooled by the air flowing past. Each is placed close to a fuel spray nozzle, usually low down in the combustor, so the spark meets a rich, well atomised spray. In an annular combustor, once one region lights, the flame travels round the whole ring. In can and can-annular systems the igniters are fitted in only two of the flame tubes, and the flame spreads to the others through short tubes called interconnectors.
Part 1 · Flame spreading
Can systems light through interconnectors Only two flame tubes carry igniters Flame-tube interconnectors join neighbouring cans At light-up, pressure rises in the lit cans and pushes flame through to the next Interconnectors also equalise pressure between the cans Annular combustors need no interconnectors: one continuous ring shaft Igniters in two flame tubes only; the flame spreads to the others through the interconnectors. igniter interconnector
Chapter 25 · Gas Turbine Ignition
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
In a can or can-annular combustion system, the flame tubes are separate, so how do they all light? Only two of them, often the lower ones, carry igniters. Neighbouring flame tubes are joined by short tubes called interconnectors. When the cans with igniters light up, the pressure in them rises sharply, and that pushes burning gas through the interconnectors into the next cans, which light in turn until all are burning. Once the engine is running, the interconnectors have a second job: they keep the pressure equal between the cans. An annular combustor is a single continuous ring, so it needs no interconnectors; the flame simply spreads round it.
Part 2 · How much energy
High energy and low energy ignition High energy (HE) units: about 12 joules per spark (range 6 to 12 J ), for starting A joule is one watt for one second Using HE whenever there is a flame-out risk would erode the plugs quickly So many engines have a combination system : HE for starting plus low energy (LE, 3 to 6 J ) for continuous use LE: take-off from contaminated runways , flight in heavy precipitation Energy per spark
0
2
4
6
8
10
12
14
Joules per spark 3 – 6 J Low energy continuous 6 – 12 J High energy starting, relight 1 joule = 1 watt for 1 second HE wears the igniter plug out much faster
Chapter 25 · Gas Turbine Ignition
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
How powerful is the spark? High energy ignition units deliver about twelve joules per spark, generally somewhere between six and twelve joules, and they are used for starting. A joule is a watt for a second, so this is a lot of energy for a spark. Now, ignition is sometimes wanted for long periods, for instance during a take-off from a contaminated runway or flight through heavy rain, to stop the engine flaming out. Running the high energy system for that long would erode the igniter plugs so quickly that their life would be cut dramatically. So many engines have a combination system. The high energy selection, six to twelve joules, is used for starting. A low energy selection, three to six joules, is used for continuous ignition.
Part 2 · Worked example
A short, very intense spark One discharge: 12 J released in about 100 µs Peak power = 12 J ÷ 0.0001 s = 120 kW Sparking rate 60 to 100 per minute : about one or two a second Average power at 100 per minute: only about 20 W So the spark is high voltage and high current , but very brief High volts, high current, briefly
0.0
0.5
1.0
1.5
2.0
Time (s)
Discharges (12 J each) 100 per minute: one every 0.6 s 12 J in about 100 µs → peak about 120 kW but 12 J × 100 per minute → only about 20 W average A very short, very intense spark
Chapter 25 · Gas Turbine Ignition
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put some numbers on that spark. Suppose the unit releases twelve joules in about a hundred microseconds, which is a ten thousandth of a second. Twelve joules divided by a ten thousandth of a second is a peak power of about one hundred and twenty kilowatts, enough to blast through fuel spray and even through water. That is why we describe the spark as high voltage and high current. But the unit fires only sixty to a hundred times a minute, about once or twice a second. At a hundred sparks a minute, twelve joules each, the average power is only about twenty watts. So the unit takes a modest current from the aircraft supply, stores it up, and lets it go in one short, violent discharge.
Part 3 · When
Start, continuous and automatic ignition START auto with the start cycle CONTINUOUS selected by the crew AUTO e.g. from the stall warning start selected speed switch: off contaminated runway, heavy rain, turbulence… stall detected time → Start ignition is cancelled automatically , typically by a speed switch driven from the HP (N2) indication, after self-sustaining speed.
Chapter 25 · Gas Turbine Ignition
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are three ways the igniters get switched on. Start ignition comes on automatically when the start sequence begins, or when the crew opens the H P fuel cock, moves the start lever or selects the fuel and ignition switch. It is cancelled automatically at some point after the engine passes self-sustaining speed, typically by a speed switch in the H P r p m indication. Continuous ignition is selected by the crew on the engine start panel, and it uses the low energy mode of the igniters. It stays on for as long as it is selected, for example on a contaminated runway or in heavy rain. Automatic ignition is fitted to some aircraft. It is typically triggered by the stall warning system, which selects continuous ignition when a stall is detected.
Part 3 · When
When the igniters are used Situation Ignition Why Engine start (ground or air) High energy , automatic with the startLight the fuel spray; cancelled by a speed switch In-flight relight after flame-out High energy Re-light a windmilling engine Take-off and landing on contaminated runways Continuous (low energy)Water or slush ingestion could cause flame-out Heavy rain, hail, severe turbulence, icing Continuous (low energy)Precaution against flame-out High angle of attack / stall Automatic (from stall warning)Disturbed intake airflow can cause flame-out Normal cruise Off Flame is self-sustaining; save the plugs
Exam wording: igniters may be energised for starting, for in-flight relighting, in heavy rain, for take-off and landing, and at high angles of attack.
Chapter 25 · Gas Turbine Ignition
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
This table brings the uses together. For an engine start, on the ground or in the air, the high energy ignition comes on automatically and is cancelled by the speed switch. For a relight after a flame-out in flight, the high energy system is used again. Continuous ignition, at low energy, is used as a precaution whenever the flame could be put out: take-off and landing on contaminated runways, where water or slush may be ingested, and flight through heavy rain, hail, severe turbulence or icing. On some aircraft, automatic ignition comes on at high angles of attack, triggered by the stall warning, because the disturbed airflow into the intake could cause a flame-out. In normal cruise the igniters are off: the flame looks after itself and the plugs are saved.
Part 4 · The ignition unit
Inside the high energy ignition unit High energy ignition unit (28 V DC) 28 V DC Trembler interrupts the DC Transformer up to 25 000 V AC Rectifier AC → DC Reservoir capacitor Discharge resistors bleed off charge Discharge gap sealed Choke prolongs the spark Safety resistor Igniter plug in the combustion chamber Principle: charge a very large capacitor , then discharge it across the face of the igniter plug .
Chapter 25 · Gas Turbine Ignition
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole high energy ignition unit, supplied in this case with twenty eight volts D C. The principle is simple: charge up a very large capacitor, then discharge it across the face of the igniter plug. On the left, the supply feeds the trembler and the primary coil of a transformer. The transformer steps the voltage up. The rectifier turns it back into direct current, which charges the reservoir capacitor. Across the capacitor sit the discharge resistors. When the capacitor voltage is high enough, the sealed discharge gap breaks down, and the energy flows through the choke to the igniter plug in the combustion chamber. A safety resistor sits across the output. Over the next three slides we take each stage in turn.
Part 4 · Stage 1
Charging: trembler, transformer, rectifier 28 V DC feeds the primary coil through the trembler The trembler buzzes like an electric bell , chopping the current into a crude AC (sawtooth) By transformer action the secondary boosts it to about 25 000 V Rectifiers turn it back into DCThe DC charges the reservoir capacitor 28 V DC supply aircraft busbar Trembler chops the DC: sawtooth Transformer steps up to ~25 000 V Rectifier back to DC Capacitor stores the charge Discharge gap breaks down Choke prolongs the spark Igniter plug in the combustor Discharge resistors Safety resistor Charge a large capacitor, then dump it into the plug
Chapter 25 · Gas Turbine Ignition
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us follow the charging stage. A transformer only works with alternating current, but the aircraft supply here is twenty eight volts D C. So the supply goes to the primary coil through a trembler, a vibrating contact that works just like an electric bell. It makes and breaks the circuit many times a second, so the primary current becomes a sawtooth wave, a very crude form of A C. By transformer action that changing current induces a much higher voltage in the secondary coil, boosted to around twenty five thousand volts. That high voltage A C is then changed back to D C by the rectifiers, and the direct current charges the reservoir capacitor. Watch the gauge: the capacitor charges, and then, as we will see next, the gap breaks down and it discharges.
Part 4 · Stage 2
Discharge: the gap and the choke Charge builds until it can jump the sealed discharge gap The energy then flows through the choke , an inductance The choke slows the discharge , so the spark lasts longer A longer spark gives a better chance of lighting the fuel spray Rate: about 60 to 100 sparks a minute , at random 28 V DC supply aircraft busbar Trembler chops the DC: sawtooth Transformer steps up to ~25 000 V Rectifier back to DC Capacitor stores the charge Discharge gap breaks down Choke prolongs the spark Igniter plug in the combustor Discharge resistors Safety resistor Charge a large capacitor, then dump it into the plug
Chapter 25 · Gas Turbine Ignition
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the discharge. As the capacitor charges, its voltage rises until it is enough to break down the sealed discharge gap. At that moment the stored energy rushes out. Before it reaches the plug it passes through the choke. A choke is an inductance, a coil that opposes any rapid change in current. It slows the flow of energy down, so instead of an extremely short crack, the spark at the igniter lasts a little longer, which gives the fuel spray a better chance of catching light. Then the capacitor recharges and the cycle repeats, about sixty to a hundred times a minute. The rate is random, so if both units on an engine are working you hear two unsynchronised ticking beats from the jet pipe.
Part 5 · Safety
Discharge resistors and the safety resistor The capacitor charge is potentially lethal Discharge resistors : bleed the charge away to zero when the supply is switched off So the unit is safe to handle after removal for servicing Safety resistor : if the igniter plug is disconnected , excess energy flows through itWithout it the charge would keep building and could make the capacitor explode 28 V DC supply aircraft busbar Trembler chops the DC: sawtooth Transformer steps up to ~25 000 V Rectifier back to DC Capacitor stores the charge Discharge gap breaks down Choke prolongs the spark Igniter plug in the combustor Discharge resistors Safety resistor Charge a large capacitor, then dump it into the plug
Chapter 25 · Gas Turbine Ignition
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The capacitor in this unit is big enough to kill, so two kinds of resistor make it safe. The discharge resistors are connected across the capacitor. When the supply is switched off, any charge left in the capacitor leaks away through them to zero. That protects an engineer who removes the unit for servicing and touches its casing. The safety resistor sits across the output, and acts as a kind of safety valve. If the igniter plug or its lead becomes disconnected, the energy has nowhere to go, so the charge would keep building up and could eventually make the capacitor explode. The safety resistor lets energy above the normal level flow through it, so the charge stays balanced. Remember: discharge resistors for switching off, safety resistor for a disconnected plug.
Part 5 · Worked example
How much energy the capacitor holds Stored energy = ½ × C × V² A 4 µF capacitor at 2 450 V holds about 12 J : a high energy spark The same capacitor at 1 730 V holds about 6 J : a low energy spark Voltage × 1.41 → energy × 2; voltage × 2 → energy × 4 Treat every unit as live until its resistors have discharged it Energy stored in the capacitor
0
1,000
2,000
3,000
0
5
10
15
20
Capacitor voltage (V)
Energy (J), 4 µF capacitor 2 450 V → 12 J 1 730 V → 6 J Energy = ½ × capacitance × voltage² double the voltage → four times the energy which is why the unit is lethal
Chapter 25 · Gas Turbine Ignition
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
How much energy can a capacitor hold? The stored energy is a half, times the capacitance, times the voltage squared. Take a four microfarad capacitor, a typical size for illustration. Charged to about two thousand four hundred and fifty volts, it holds about twelve joules, the energy of one high energy spark. Charge the same capacitor to only about one thousand seven hundred and thirty volts and it holds about six joules, a low energy spark. Notice the square: increase the voltage by about forty one per cent and the energy doubles; double the voltage and the energy goes up four times. A few joules delivered through the human body can be fatal, which is why every ignition unit must be treated as live until its discharge resistors have done their job.
Part 5 · Handling
Working safely near ignition systems Isolate the supply, then wait the stated time before disconnecting anything Disconnect the HT lead at the plug end first and earth it Never touch the plug or lead while the system could be energised Never fire an igniter in the open near fuel vapour or people Units powered from AC and transistorised units exist too: same hazard Lethal stored energy Isolate the supply and wait the stated time before touching the unit or the HT lead Never touch an igniter plug while the system could fire; never fire with the plug outside the engine near people or fuel vapour
Chapter 25 · Gas Turbine Ignition
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the stored energy can be lethal, maintenance manuals lay down strict precautions, and as a pilot you should understand why. After isolating the supply, wait for the stated time so that the discharge resistors can drain the capacitor before anything is disconnected. Then the high tension lead is disconnected and its end is earthed. Nobody should touch an igniter plug or its lead while the system could be energised, and an igniter must never be fired in the open near fuel vapour or people. Not every unit has a trembler like the one we studied. There are transistorised units, and for aircraft with A C electrical systems there are units that work from that supply. The hazard is exactly the same.
Part 6 · Igniter plugs
Air gap and surface discharge igniter plugs Older type: air gap high tension body (earth) insulator centre (hot) electrode large air gap, like a big spark plug needs very good insulation about 25 000 V to jump the gap Surface discharge low tension, used today body (earth) insulator centre (hot) electrode semiconductor pellet surface ionised: flash-over across the face needs only about 2 000 V The surface discharge plug is the modern type: a semiconductor tip lets it fire at about 2 000 V instead of about 25 000 V.
Chapter 25 · Gas Turbine Ignition
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two types of igniter plug. The older type works much like a piston engine spark plug, but with a far bigger gap. About twenty five thousand volts are needed to make a spark jump that gap, so the plug, the lead and the unit need very good insulation. The modern type is the surface discharge igniter plug. Here the end of the insulator, between the centre electrode and the body, is made of a semiconductor material. A small leakage current flows from the hot centre electrode across the semiconductor to the body. That leakage heats and ionises the surface, making a low resistance path. The energy stored in the capacitor then discharges along it as a high intensity flash-over from the centre electrode to the body, and this needs only about two thousand volts.
Part 6 · Surface discharge
How the surface discharge plug fires The insulator tip is a semiconductor pellet Leakage current from the centre electrode to the body ionises its surface This gives a low resistance path for the stored energy Discharge: a high intensity flash-over across the face Low voltage (~2 000 V) means less insulation trouble; but plug tips erode with use Older type: air gap high tension body (earth) insulator centre (hot) electrode large air gap, like a big spark plug needs very good insulation about 25 000 V to jump the gap Surface discharge low tension, used today body (earth) insulator centre (hot) electrode semiconductor pellet surface ionised: flash-over across the face needs only about 2 000 V
Chapter 25 · Gas Turbine Ignition
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us look more closely at the surface discharge plug in section. The outer plug body is the earth electrode. Inside it is an insulator, and through the middle runs the centre electrode, the hot electrode. At the firing end, the insulator is replaced by a semiconductor pellet. When the ignition unit starts to charge, a small leakage current creeps across the semiconductor from the centre electrode to the body, and ionises its surface. Now there is a low resistance path, and the capacitor energy discharges across the whole face as a bright flash-over. Watch the flash at the tip. Because only about two thousand volts are needed, insulation is much less of a problem. The intense discharge does erode the tip, which is one more reason to use high energy only when necessary.
Part 6 · The complete system
Two units, two leads, two plugs Each igniter has its own unit and its own screened HT lead The two units spark independently, at random Ground check: listen at the jet pipe for two unsynchronised beats One failure still leaves a working igniter Some crews alternate igniter A and B on successive starts to check both Igniter 1 Igniter 2 looking aft at the combustor fuel spray nozzles Two igniters, low in the combustor, each beside a spray nozzle
Chapter 25 · Gas Turbine Ignition
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now we can put the complete system together. Each of the two igniter plugs has its own ignition unit and its own screened high tension lead, so the two halves are completely independent. Because each unit fires at its own random rate, sixty to a hundred times a minute, the two never stay in step. That gives engineers a simple ground check: with relight or ignition selected before engine start, someone listening at the jet pipe should hear two unsynchronised ticking beats, which proves that both units are working. If one unit or plug fails, the other can still light the engine. On many aircraft the crew selects igniter A on one start and igniter B on the next, so that both are proved regularly.
Part 7 · In use
Ignition during a normal start The starter turns the HP spool; fuel and ignition at the stated N2 Light-up : EGT rises and the engine accelerates fasterIgniters stay on through the acceleration Cancelled automatically by a speed switch after self-sustaining speed (about 30% N2) The HP fuel cock must not be opened until the compressor is turning at the right speed, the right way Ignition during a ground start
0
10
20
30
40
50
60
0
20
40
60
Time from start selection (s)
N2 (%) igniters on light-up self-sustaining ≈ 30% speed switch: igniters off Fuel and ignition at the stated N2, then cancelled automatically once the engine is past self-sustaining
Chapter 25 · Gas Turbine Ignition
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us see how ignition fits into a normal start. The starter turns the H P spool, and air begins to flow through the engine. When N two reaches the speed stated for that engine, fuel and ignition are switched on. Notice the rule here: the H P fuel cock must not be opened until the compressor is turning at the correct speed and in the correct direction. Shortly afterwards the engine lights up, which you see as a rise in exhaust gas temperature and a faster acceleration. The igniters stay on while the engine accelerates. Once it is past self-sustaining speed, around thirty per cent N two, a speed switch in the H P r p m system cancels the ignition, and the starter is cut out too.
Part 7 · Relight
Relighting in flight A relight restarts a flamed-out engine, usually in the air Windmill relight : fuel and ignition on, no starter; ram air turns the enginePossible only inside the relight envelope of altitude and airspeed Starter-assisted relight extends the envelope at low speed Success shows as a rise in EGT or RPM Typical windmill relight envelope
100
150
200
250
300
350
0
10
20
30
40
Indicated airspeed (kt)
Altitude (thousand ft) relight possible too thin, too slow too fast: flame blown out Relight uses the high energy (starting) ignition; figures are illustrative, each engine has its own
Chapter 25 · Gas Turbine Ignition
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
A relight is the restarting of an engine that has flamed out, usually while airborne. After a flame-out, the engine keeps turning, windmilling in the airflow. For a windmill relight the crew selects fuel and ignition without the starter, and lets the ram air keep the engine turning. It only works within a relight envelope of altitude and airspeed. At low speed the engine does not windmill fast enough to supply the air the combustor needs, and high up the air is too thin. At very high speed the airflow through the combustor is so fast that the flame is blown out again. On some engines the starter can assist at low speeds. A successful relight shows up as a rise in either the exhaust gas temperature or the r p m.
Comparison
Piston engine and gas turbine ignition Piston engine (magneto) Gas turbine When it fires Every power stroke, all the time Only to start, relight, or as a precaution Energy source Self-contained magneto, engine-driven Aircraft supply (28 V DC or AC), stored in a capacitor Energy per spark Tens of millijoules 3 to 12 joules Timing Timed to the crankshaft Random, 60–100 per minute Plugs Two per cylinder Two per engine , surface dischargeDanger Live magneto if P-lead broken Lethal stored charge
Chapter 25 · Gas Turbine Ignition
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
It helps to compare this with what you learned about piston engine ignition. A magneto fires on every power stroke for as long as the engine runs, and it is self-contained, driven by the engine. A gas turbine fires its igniters only to start, to relight, or as a precaution, and it takes its energy from the aircraft supply and stores it in a capacitor. The energy per spark is hugely different: tens of millijoules for a spark plug, three to twelve joules for an igniter, hundreds of times more. Magneto sparks are precisely timed to the crankshaft; igniter sparks are random, sixty to a hundred a minute. A piston engine has two plugs per cylinder, a gas turbine two per engine. And the danger: a live magneto from a broken P-lead, a lethal capacitor in the turbine.
Exam traps
Points examiners like to test Principle HE ignition works by the discharge of a capacitor , not by magneto induction.
The choke The choke prolongs the discharge to the plug.
Discharge resistors Let the capacitor discharge when the unit is switched off .
Rate About 60 to 100 discharges per minute , not per second.
HE or LE HE: starting and high-altitude relight . LE: continuous , e.g. contaminated-runway take-off.
Cancelled by Start ignition is switched off by a speed switch , not a timer or centrifugal force.
Chapter 25 · Gas Turbine Ignition
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the favourite exam traps. The high energy ignition unit works by discharging a capacitor, not by magneto induction and not by a simple step-up transformer from the A C supply. The choke prolongs the discharge to the plug. The discharge resistors let the capacitor discharge when the unit is switched off; the safety resistor protects against a disconnected plug. The sparking rate is sixty to a hundred per minute, not per second. High energy ignition is used for starting and for relighting at altitude; low energy is used continuously, for example on take-off from a contaminated runway or in heavy rain. And start ignition is cancelled by a speed switch, not by a timer, an interlock or centrifugal force. The spark itself is high voltage and high current.
Summary
Gas turbine ignition in one page Why Flame is continuous: ignition only to start, relight, or as a precaution.
Dual system Two units, two leads, two plugs near spray nozzles. Interconnectors spread flame in can systems.
Energy HE 6–12 J (≈12 J) for starting; LE 3–6 J for continuous use; HE erodes plugs.
Selections Start (auto, speed switch off), continuous (crew), automatic (stall warning), relight.
Unit 28 V DC → trembler → transformer → rectifier → capacitor → gap → choke → plug.
Safety Discharge resistors drain the charge at switch-off; safety resistor for an open plug.
Plugs Air gap ~25 000 V; surface discharge (semiconductor) ~2 000 V.
Rate 60–100 sparks a minute, random: two unsynchronised beats.
Chapter 25 · Gas Turbine Ignition
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. A gas turbine’s flame is continuous, so ignition is used only to start, to relight, or as a precaution. The system is dual: two units, two leads and two plugs, placed near spray nozzles, with interconnectors spreading the flame in can systems. High energy ignition gives six to twelve joules, typically about twelve, for starting; low energy gives three to six joules for continuous use, which saves the plugs. Start ignition is automatic and cancelled by a speed switch, continuous ignition is selected by the crew, and automatic ignition may come from the stall warning. The unit charges a capacitor through a trembler, transformer and rectifier, then discharges it through a gap and a choke. Discharge resistors drain it at switch-off; a safety resistor protects against an open plug. And the sparks come sixty to a hundred times a minute.