Engines · Chapter 20
Gas Turbine Lubrication How a gas turbine keeps its bearings and gears alive: the dry-sump recirculatory system, relief-valve and full-flow systems, pumps, filters, coolers, chip detectors, seals, the centrifugal breather and synthetic oils.
oil jet roller bearing fed by an oil jet © 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter twenty is about the oil system of a gas turbine. A jet engine has far fewer rubbing parts than a piston engine, but its main bearings spin at very high speed, some of them next to the hottest parts of the engine, and its oil also cleans, protects against corrosion and, in turboprops, works the propeller. We will follow the oil round a typical dry-sump system, compare the relief-valve and full-flow systems, and look at every component on the way, from tank and pumps to coolers, chip detectors, seals and the centrifugal breather, finishing with synthetic oils and what the cockpit indications tell the pilot.
Roadmap
What this chapter covers 1 · Purpose and layout Why oil is needed, the bearings, the dry-sump recirculatory system and the whole circuit.
2 · Two systems Pressure relief valve and full-flow systems; the turboprop system and torquemeter.
3 · Components Jets, tank, pumps, aeration, air and fuel-cooled coolers, chip detectors, filters.
4 · Seals, oils, faults Labyrinth seals, the centrifugal breather, synthetic oils, indications and fault-finding.
Chapter 20 · Gas Turbine Lubrication
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how we will work through gas turbine lubrication. First, why the oil is there and what it lubricates, and the overall layout of a dry-sump recirculatory system, with the whole circuit in three dimensions. Second, the two basic systems, the pressure relief valve system and the full-flow system, plus the turboprop version with its torquemeter. Third, the components one by one: oil jets, the tank, pumps, the air-laden scavenge oil, oil coolers including the fuel-cooled oil cooler, chip detectors and filters. Finally, how bearing chambers are sealed and vented, the synthetic oils used, and what the oil indications and some classic faults tell you.
Part 1 · Purpose and layout
Five jobs for the oil Reduce friction A film between bearings and gear teeth turning at very high speed.
Cool Carries heat away from the bearings, especially at the hot end of the engine.
Clean Carries dirt and wear debris to the filters, where it stays until the filter is changed.
Protect Coats the steel bearings so they cannot oxidise: minimises corrosion.
Hydraulic medium In many turboprops engine oil works the propeller pitch-change mechanism.
Measure In some turboprops boosted oil pressure balances the reduction gear: the torquemeter.
Chapter 20 · Gas Turbine Lubrication
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Oil in a gas turbine does much more than reduce friction. However clean the engine is kept, some dirt and wear particles get inside, and the oil carries them to the filters before they can damage bearings or block the small oil passages. Most engine bearings are steel, which would soon corrode, so a coating of oil protects them. The bearings, especially those at the hot end near the turbine, need cooling, and the oil is the cooling medium too. In many turboprop engines the oil is also a hydraulic fluid: some of it goes to the propeller pitch-change mechanism. And in some turboprops, oil boosted to high pressure balances the reduction gear, giving the torquemeter reading. So: friction, cooling, cleaning, corrosion protection and hydraulic work.
Part 1 · Purpose and layout
What has to be lubricated Far fewer rubbing parts than a piston engine: no pistons, rings or valve gear Main shaft bearings: ball bearings locate the shaft and take thrust, roller bearings take radial load Bearings sit in sealed bearing chambers fed by oil jets Gears and bearings in the accessory and reduction gearboxes The rear bearings run next to the turbine: oil must cool them What needs oil in a gas turbine compressor combustor turbine front ball (thrust) centre roller rear roller, hottest accessory gearbox Main bearings: ball bearings take the thrust, rollers the radial load Bearings sit in sealed bearing chambers , fed by oil jets Gears and bearings in the gearboxes Turboprop: reduction gear and propeller pitch control
Chapter 20 · Gas Turbine Lubrication
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
A gas turbine has far fewer rubbing parts than a piston engine. There are no pistons, rings or valve gear, just rotating shafts supported on bearings, and gears in the gearboxes. Each spool is held by a ball bearing, which locates it and takes the axial thrust, and by roller bearings, which take the radial load and let the shaft grow in length as it heats up. These bearings sit inside sealed bearing chambers and are fed by oil jets. The accessory gearbox and, on a turboprop, the reduction gearbox also need oil for their gears and bearings. Notice where the rear bearing sits: right beside the turbine. That is why cooling is such an important job for the oil, and why the oil must cope with high temperatures.
Part 1 · Purpose and layout
A dry-sump recirculatory system Most engines use a self-contained, recirculatory system: pumps take the oil round and back to a tank Dry sump : scavenge pumps keep the bearing chambers and gearboxes nearly emptyOil is always synthetic , because of the high temperatures Level checked shortly after shut-down Oil is not changed routinely ; filters are removed, washed and inspected for debris Dry sump: oil lives in a separate tank Tank most of the oil Engine bearing chambers, gearboxes pressure pump scavenge pumps chambers kept nearly dry Oil type synthetic (high temperatures) Level check shortly after shut-down Oil change not routine: topped up as it is used Why it is used seals pass some oil; synthetic oil does not break down Filters removed, washed, inspected regularly Debris tells the engineers the wear rate
Chapter 20 · Gas Turbine Lubrication
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Most gas turbines use a self-contained recirculatory system. Pumps distribute the oil round the engine and return it to a separate tank, so it is a dry-sump system: scavenge pumps keep the bearing chambers and gearboxes almost empty. The oil is invariably synthetic, because of the high temperatures involved. The level is checked shortly after shut-down, while the oil is still distributed as it was in running. Unlike a piston engine, the oil is not changed on a regular basis. Gas turbines use a little oil all the time through their air seals, so it is constantly topped up, and synthetic oil does not break down and oxidise the way mineral oil does. The filters, however, are removed, washed and refitted at regular intervals, and the debris they hold shows the engineers how fast the engine is wearing.
Part 1 · Purpose and layout
The whole oil circuit Oil tank de-aerator tray Pressure pump Pressure filter Bearing chamber oil jets onto the bearing chip detector Scavenge pump Oil cooler Breather gearbox vent air out red: pressure oil blue: scavenge (return) oil amber: oil from the tank
Chapter 20 · Gas Turbine Lubrication
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole circuit working. Oil leaves the tank and goes to the pressure pump, which sends it, now as red pressure oil, through the pressure filter and on to the oil jets in the bearing chamber, where it sprays onto the main bearing. Having done its work, the oil falls to the bottom of the chamber. From there, the scavenge pump draws it out, past a chip detector that catches any iron particles. The scavenge oil, shown in blue, is pushed through the oil cooler, where it gives up its heat, and returns to the tank, where a de-aerator tray lets the air escape. Air and oil mist from the chambers and gearbox leave through the breather. Keep this loop in mind; every component we meet sits somewhere on it.
Part 2 · Two systems
The pressure relief valve system A spring-loaded relief valve limits the pressure in the feed line It opens at the pressure the pump makes at engine idling speed So the feed pressure is constant over the whole speed range and oil temperature range Excess oil is spilled back to the pump inlet side A suction filter protects the pump; a pressure filter follows it Pressure relief valve system Tank Pump Oil jets spring-loaded relief valve excess spilled back to the pump inlet / tank Valve opens at the pressure the pump makes at idle: constant feed pressure at all speeds and oil temperatures.
Chapter 20 · Gas Turbine Lubrication
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two basic recirculatory systems. In the pressure relief valve system, a spring-loaded valve limits the pressure in the feed line, and so controls the flow of oil to the bearing chambers. The designer chooses one pressure that is right for all conditions, and the valve is set to open at the pressure the pump produces at engine idling speed. As a result the feed pressure stays constant over the whole range of engine speeds and oil temperatures: as the engine speeds up, the pump delivers more, but the extra is simply spilled back through the valve. In the usual layout, oil is drawn through a suction filter, which protects the pump from any debris in the tank, then pumped through the pressure filter to the relief valve and the feed jets.
Part 2 · Two systems
The full-flow system No relief valve : the pump supplies the jets directlyFlow and pressure rise with engine speed , giving the oil needed throughout the range Allows smaller pressure and scavenge pumps : no oil wasted by spilling at high speed Differential pressure switch across the pressure filter warns of blockageGalleries: one to the gearbox bearings (with pressure transmitter and low-pressure switch), one to the spool bearings Full-flow system (no relief valve) Tank Pump Pressure filter ΔP switch Gallery 1 gearbox bearings Gallery 2 spool bearings P P: transmitter + LP switch Pump feeds the jets directly: flow and pressure rise with engine speed Smaller pressure and scavenge pumps: nothing spilled at high rpm Filter ΔP switch warns of blockage (servicing panel, sometimes cockpit) Cockpit: oil pressure, low-pressure warning, quantity and temperature
Chapter 20 · Gas Turbine Lubrication
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The full-flow system gets the oil the engine needs over its entire speed range by letting the pressure pump feed the jets directly, with no relief valve. Because nothing is spilled back at high speed, the pressure and scavenge pumps can be smaller than in a relief-valve system. Oil is drawn through a suction filter, pumped through the pressure filter, and sent to the distribution galleries. Across the pressure filter is a differential pressure switch that warns of a blockage, usually on the ground crew servicing panel and sometimes on the flight deck. One gallery carries the oil pressure transmitter and the low oil pressure warning switch and feeds the accessory gearbox bearings; the other feeds the bearings supporting the compressor spools. In the cockpit you see oil pressure, quantity and temperature, plus the warnings.
Part 2 · Two systems
Relief valve or full flow: the numbers Feed pressure at the oil jets 0 20 40 60 80 100 0.00 0.25 0.50 0.75 1.00 Engine speed (% of maximum) Pressure (fraction of max) ground idle relief valve: constant above idle full flow: rises with speed Relief-valve system: where the oil goes 0 20 40 60 80 100 0.00 0.25 0.50 0.75 1.00 Engine speed (% of maximum) Flow (fraction of max) pump delivery spilled back flow to the jets full-flow pump (smaller) Computed: positive-displacement pumps (flow ∝ rpm) feeding fixed jets (pressure ∝ flow²); relief valve set to the idle pressure.
Chapter 20 · Gas Turbine Lubrication
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
These graphs are computed for gear pumps, whose delivery rises in proportion to r p m, feeding fixed oil jets, where the pressure needed rises with the square of the flow. On the left, the relief-valve system, in red, climbs to its setting at ground idle and then holds that pressure flat all the way to full speed. The full-flow system, in blue, has no valve, so its pressure keeps rising with engine speed. On the right, look at where the oil goes in the relief-valve system. Above idle the jets take a constant flow, but the pump delivers more and more, so a growing share, the shaded area, is spilled back. That wasted capacity is why a full-flow system can use smaller pressure and scavenge pumps.
Part 2 · Two systems
A turboprop oil system Oil goes forward to the propeller pitch control and aft through the hollow shaft to the turbine bearings A torquemeter pump boosts some oil to as much as 600 psi Used oil falls into trays and is collected by several scavenge pumps (dry sump) Scavenge oil → oil cooler → de-aerator tray → tank (here round the intake) Oil mist vented through a centrifugal breather in the gearbox Oil in a turboprop (relief-valve type) pitch control oil tank round the intake oil through the hollow shaft to the rear bearings oil cooler Oil: lubricant, coolant, cleaner and hydraulic fluid for pitch change Torquemeter pump boosts oil to as much as 600 psi Scavenge pumps → oil cooler → de-aerator tray → tank Oil mist vented through the centrifugal breather in the gearbox
Chapter 20 · Gas Turbine Lubrication
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a relief-valve system on a turboprop. Oil goes forward to the propeller, where some of it works the pitch-change mechanism, and in this engine it also travels through the hollow interior of the compressor-turbine shaft all the way to the rear, to the turbine bearings. A separate torquemeter pump boosts oil to a much higher pressure, as much as six hundred pounds per square inch in some engines, for the reduction gear. When the oil has finished lubricating, cooling, cleaning and working the propeller, it falls into collecting trays and is picked up by several scavenge pumps, one pressure pump but several scavenge pumps in the same pack, keeping it a dry-sump system. The scavenge oil passes through an air-cooled oil cooler and a de-aerator tray into the tank, which here surrounds the engine intake.
Part 2 · Two systems
The torquemeter Helical gears in the reduction gear produce an axial thrust proportional to the torque Boosted oil pressure on a piston balances that thrust So the torquemeter oil pressure is an accurate measure of torque Reference figures for temperature and pressure give the minimum torque the engine should give Power: SHP = 2π × rpm × torque (lb ft) ÷ 33 000 Torquemeter: oil pressure measures torque helical gear axial thrust oil piston psi Oil pressure balances the gear thrust, so pressure ∝ torque Torque 4 000 lb ft Propeller speed 1 000 rpm SHP = 2π × N × torque ÷ 33 000 ≈ 762 SHP Reference charts give the minimum torque for the day: a power check.
Chapter 20 · Gas Turbine Lubrication
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The torquemeter is a neat use of the oil. The reduction gear of a turboprop uses helical gears, and the angled teeth push the gear sideways, along its axis, with a force proportional to the torque being transmitted. Oil boosted by the torquemeter pump acts on a piston that balances this axial thrust. The more torque, the higher the oil pressure needed to hold the gear in place, so measuring the torquemeter oil pressure gives an accurate indication of the torque going to the propeller. With charts that take account of the outside air temperature and pressure, the pilot can find the minimum torque the engine should be capable of producing that day. And from torque you get power. For example, four thousand pound feet at one thousand propeller r p m is about seven hundred and sixty shaft horsepower.
Part 3 · Components
Oil jets and the return path Oil jets sit very close to the bearings so turbulence cannot deflect the oil Thread-type "last chance" filters just before the jets catch anything the pressure filter missedUsed oil collects at the bottom of the chamber On its way to the scavenge pump it passes a chip detector and a scavenge filter Oil jet, bearing and scavenge path bearing chamber roller bearing thread-type "last chance" filter jet aimed close to the bearing chip detector scavenge filter scavenge pump Jets close to the bearing so turbulence cannot deflect the oil. Return oil passes a chip detector and a scavenge filter.
Chapter 20 · Gas Turbine Lubrication
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Inside each bearing chamber the oil arrives through jets placed very close to the bearings, so that the turbulent air in the chamber cannot blow the oil off its target. Just upstream of each jet is a small thread-type filter. This is a last-chance filter: it removes any debris that may have got past the main pressure filter, which would otherwise block the tiny jet and starve a bearing. Once the oil has done its work, it collects in the bottom of the chamber and is drawn away by the scavenge pump. Before it reaches the pump it passes over a magnetic chip detector and through a scavenge filter, so that any debris coming from that bearing is caught and can be traced to it.
Part 3 · Components
The oil tank Usually a separate tank on the side of the engine; can be part of the intake or the external gearbox Filling by gravity or, more normally, by pressure Contents by sight glass or dipstick , sometimes both De-aerator tray removes air bubbles from the returning oilSpace above the oil for expansion and froth A typical oil tank de-aerator tray: air bubbles escape return oil in gravity filler pressure fill sight glass to pressure pump Mounted on the engine, or part of the intake or gearbox. Contents by sight glass and/or dipstick; space left for expansion.
Chapter 20 · Gas Turbine Lubrication
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil tank is normally a separate unit mounted on the side of the engine, although on some engines it forms part of the air intake, as we saw on the turboprop, or is built into the external gearbox. A separate tank must have a way of filling it: by gravity through a filler cap, or, more normally, by pressure through a connection the engineers couple a servicing rig to. There must be a way of checking the contents, a sight glass or a dipstick, and sometimes both. Returning scavenge oil enters over a de-aerator tray, which spreads it out so that the air bubbles it carries can escape before the oil goes back into service. Space is left above the oil to allow for expansion and froth.
Part 3 · Components
Oil pumps Gear-type pumps : steel gears meshing in a close-fitting aluminium housingOil is carried round in the tooth spaces from inlet to outlet A pump pack on the accessory gearbox: one pressure pump and up to six scavenge pumps The drive has no shear neck : the pumps must keep going as long as possible If an oil pump fails, shut the engine down Gear-type oil pump inlet outlet oil carried round the outside in the tooth spaces Steel gears in a close-fitting aluminium housing Pump pack on the accessory gearbox: 1 pressure + up to 6 scavenge pumps Scavenge capacity is larger than pressure capacity No shear neck on the drive: keep pumping as long as possible
Chapter 20 · Gas Turbine Lubrication
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Both the pressure and the scavenge pumps are normally gear-type pumps: a pair of meshing steel gears in a close-fitting aluminium housing. As the gears turn, oil is carried round the outside in the spaces between the teeth, from the inlet to the outlet, and it cannot get back through the middle because the teeth are in mesh. The pumps are mounted together in a pump pack on the accessory gearbox, usually one pressure pump and perhaps as many as six scavenge pumps, all on one drive. Oil pumps are so vital that their drive shaft is not given a shear neck: they must keep supplying oil as long as possible, whatever the damage. And if an oil pump does fail, the engine must be shut down immediately; it cannot run without lubrication.
Part 3 · Components
Why scavenge oil is aerated Bearing chambers are pressurised with compressor air to keep the oil in That air mixes with the oil and is churned by the bearings: the scavenge oil is aerated Aerated oil has a much larger volume So scavenge pumps have greater capacity than the pressure pump The de-aerator and the breather get rid of the air Why scavenge oil is full of air sealing air sealing air oil churned with the air: froth aerated oil, larger volume Bearing chambers are pressurised with compressor air That air mixes with the oil: the scavenge oil is aerated So scavenge pumps have more capacity than the pressure pump De-aerator tray in the tank lets the air out; the breather vents it
Chapter 20 · Gas Turbine Lubrication
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why do gas turbines need more scavenge capacity than pressure capacity? It comes down to the air. As we will see shortly, the bearing chambers are sealed by pressurising their seals with air bled from the compressor, so a steady flow of air leaks into every chamber. In there it is churned up with the oil by the spinning bearings, and the oil that collects at the bottom is full of air, aerated. Aerated oil takes up a much bigger volume than the same oil without air, so the scavenge pumps must be bigger, or more numerous, than the pressure pump if they are to keep the chambers dry. Back at the tank, the de-aerator tray releases the air, and the breather sends it overboard. So the exam answer is: oil becomes aerated because the bearings are pressurised with compressor air.
Part 3 · Components
Oil coolers Cooled by air or by fuel ; some engines use both Basically a radiator : a matrix of tubes partitioned by baffle plates Baffles make the oil take the longest path past the tubes With both types, the air cooler is switched in only when needed The fuel-cooled oil cooler (FCOC) warms the cold fuel and cools the hot oil Oil cooler matrix with baffles hot oil in cooled oil out fuel warmed baffles make the oil take the longest path round the tubes Cooled by air or by fuel; some engines use both Air cooler switched in only when needed (holds an efficient oil temperature) Fuel-cooled: cold fuel is warmed (protects the fuel filter from ice) and hot oil is cooled: two jobs in one unit
Chapter 20 · Gas Turbine Lubrication
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Oil coolers can be cooled by air or by fuel, and some engines have both. Whichever medium is used, the cooler is basically a radiator: a matrix of tubes carrying the coolant, with baffle plates that force the oil to zig-zag across the tubes, taking the longest possible path and so gaining the most cooling. Where an engine has both coolers, the oil temperature is monitored, and the air cooler is switched in only when the fuel cooler cannot cope on its own, which keeps the oil at a temperature that helps the engine's thermal efficiency. The fuel-cooled oil cooler is a clever piece of design. Fuel from the wing tanks is very cold and needs warming before it reaches the fuel filter, where ice could block it, and the oil is hot and needs cooling. One unit does both: two for the price of one.
Part 3 · Components
The FCOC: by-pass and pressure-maintaining valves Oil by-pass valve across the oil inlet and outletOpens on high inlet pressure: a blocked matrix or very viscous cold oil ; prevents oil starvation and matrix damage Pressure-maintaining valve keeps oil pressure above fuel pressure If the matrix leaks, oil leaks into the fuel , never fuel into the oil Oil temperature is measured as the oil leaves the cooler Fuel-cooled oil cooler: the two valves matrix oil by-pass valve oil in oil out fuel in fuel out pressure-maintaining valve (red) By-pass valve opens on high inlet pressure: blocked matrix or very cold, thick oil: no starvation, no matrix damage Pressure-maintaining valve keeps OIL pressure above FUEL pressure a leak sends oil into fuel, never fuel into oil Oil temperature measured as the oil leaves the FCOC
Chapter 20 · Gas Turbine Lubrication
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two valves make the fuel-cooled oil cooler safe. The first is an oil by-pass valve fitted across the oil inlet and outlet. If the pressure at the oil inlet rises past a set value, because the matrix is blocked or because very cold oil is too thick to pass, the valve opens and sends the oil straight to the outlet. That prevents oil starvation of the engine and protects the relatively fragile matrix from damage. Watch it open in the scene. The second is a pressure-maintaining valve, which ensures that the oil pressure in the cooler is always higher than the fuel pressure. Then, if the matrix is ever damaged, oil leaks into the fuel and is burnt, rather than fuel leaking into the oil, where it would thin it and create a fire risk. The oil temperature is measured as the oil leaves the cooler.
Part 3 · Components
Magnetic chip detectors Magnetic plugs fitted in the scavenge lines Between the bearing chamber and the scavenge pump They collect ferrous debris returning with the oil Iron particles on the magnet: warning of impending bearing failure Bayonet fitting in a self-sealing valve housing : removed without loss of oilMagnetic chip detector scavenge line self-sealing valve housing bayonet fitting iron particles on the magnet Fitted in each scavenge line, between the bearing chamber and the scavenge pump Collects ferrous debris carried back by the oil Debris = warning of impending failure of the bearings it serves Removed and inspected without losing oil (self-sealing housing) Some types light a cockpit warning when bridged by debris
Chapter 20 · Gas Turbine Lubrication
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chip detectors are magnetic plugs fitted into the scavenge lines, between each bearing chamber and its scavenge pump, where they collect any ferrous material coming back in the oil. A bearing that is starting to fail sheds tiny steel flakes long before it breaks up, so iron filings on a chip detector are an early warning of impending failure of the bearings in that chamber. Because there is a detector for each chamber, the engineers know exactly which bearing to look at. The detector is held in by a bayonet fitting in a self-sealing valve housing, so it can be pulled out and inspected without draining any oil. Some types are electrical and light a warning in the cockpit when debris bridges the gap. Remember: chip detectors warn of bearing failure, not cracked blades.
Part 3 · Components
Filters round the system Filter Where Type Job Suction filter Before the pressure pump Coarse strainer Stops debris from the tank damaging the pump Pressure filter Pressure pump outlet Very fine mesh Stops small particles blocking the oil jets Thread-type (last chance) Just before each oil jet Small thread filter Catches anything that got past the pressure filter Scavenge filter Each return line, just after the chip detector Fine mesh Collects debris from that component Construction Pressure and scavenge filters Tubular: woven wire cloth or resin-impregnated fibre Some have a ΔP switch or a pop-up indicator for partial blockage
Filters are removed and inspected regularly: the debris they hold shows the wear rate of the engine.
Chapter 20 · Gas Turbine Lubrication
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil's cleaning job depends on filters at several points round the circuit. The suction filter, before the pressure pump, is a coarse strainer that stops debris in the tank from being drawn into the pump and damaging it. At the pump outlet, the pressure filter is a very fine mesh that keeps small particles away from the oil jets. Just before each jet, the thread-type filter is the last chance to catch anything that slipped through. In each return line, just downstream of the chip detector, a scavenge filter collects debris returning from the component it serves. Pressure and scavenge filters are tubular, made of very finely woven wire cloth or resin-impregnated fibre, and some carry a differential pressure switch, or a small pop-up button that sticks out of the casing to show that the filter is partly blocked.
Part 4 · Seals, oils, faults
Sealing the bearing chambers Labyrinth seals : fins on the shaft running close to a stationary housing, with no rubbing contactPressurised with air from an intermediate compressor stage Air leaks inwards , so the oil stays in: minimum oil loss Inter-stage seals are used where engine sections run at different pressures A rubbing labyrinth seal: short run-down time and high oil consumption Labyrinth seal on a bearing chamber rotating shaft stationary seal housing bearing chamber (oil, low pressure) sealing air from an intermediate compressor stage (higher pressure) Air leaks INWARDS through the fins: oil cannot get out Labyrinth seals: no rubbing contact; small fin clearances throttle the leak Pressurised by air from an intermediate compressor stage to minimise oil loss Inter-stage seals separate sections at different pressures Rubbing labyrinth seal: short run-down time and high oil consumption
Chapter 20 · Gas Turbine Lubrication
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every bearing chamber has to be sealed where the shaft passes through its walls. The usual seal is a labyrinth seal: a row of thin fins on the rotating shaft runs very close to a stationary housing, without touching. The trick is pressure. The space outside the seal is fed with air from an intermediate stage of the compressor, at a higher pressure than inside the chamber, so air leaks inwards through the fins all the time, and the oil cannot escape outwards. That is why seals are pressurised: to ensure minimum oil loss. Similar inter-stage seals are used wherever two sections of the engine run at different pressures. And a classic fault: if a labyrinth seal is rubbing, the extra friction makes the engine run down quickly after shut-down, and the damaged seal lets oil out, so oil consumption is high.
Part 4 · Seals, oils, faults
The centrifugal breather and vent Sealing air builds up pressure in the chambers and gearbox: it must be vented to atmosphere The air carries oil mist ; vented directly, the oil would soon be lost The bearing chambers are vented to the gearbox, through the centrifugal breather The rotor flings the heavy oil outwards onto de-aerator segments , back into the gearbox The air, with less inertia, leaves through the centre : oil loss minimised Centrifugal breather air out rotates at high speed oil droplets flung outwards to the de-aerator segments, back to the gearbox Vents bearing chambers and gearbox so air pressure cannot build up Oil mist enters; the heavier oil is thrown outwards Air, with less inertia, leaves through the centre to atmosphere Result: minimum oil loss
Chapter 20 · Gas Turbine Lubrication
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
All that sealing air has to go somewhere, or the pressure in the bearing chambers and gearbox would build up. So the inside of the engine is vented to atmosphere. The problem is that the air is full of oil droplets, an oil mist, and if it escaped unhindered the engine would lose its oil quickly. The answer is the centrifugal breather. The bearing chambers are vented to the gearbox, through hollow shafts in some engines, and the mist must pass through the breather, a rotor in the gearbox that is rotated at high speed. As the mist enters, the heavier oil is flung outwards onto de-aerator segments round the edge and drains back into the gearbox for the scavenge pumps. The air, having less inertia, makes its way out through the centre to atmosphere. So the centrifugal breather minimises oil loss.
Part 4 · Seals, oils, faults
Synthetic gas turbine oils Property Why it matters Synthetic , not mineralMineral oils burnt, scummed and oxidised at gas turbine temperatures and speeds Low volatility Does not evaporate at high altitude High flash point Its vapour does not ignite easily near a flame or hot surface High film strength Molecules hold together under load and cling to surfaces under centrifugal force Wide temperature range Typically quoted as about −45 °C to +115 °C Low viscosity Flows well when cold-soaked; possible because there are no reciprocating parts or heavy-duty gears High viscosity index Keeps its viscosity well as it heats to working temperature
Balance: viscous enough to carry the load, thin enough to flow after a long cold soak.
Chapter 20 · Gas Turbine Lubrication
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Gas turbine oils must strike a balance: viscous enough to carry the load, yet thin enough to flow well at low temperature, for instance when starting after a long cold soak. Early engines used the mineral oils of piston engines, but at gas turbine temperatures and speeds these burnt, formed scum and oxidised, so synthetic oils were developed. Their qualities are worth learning as a list. Low volatility, so they do not evaporate at high altitude. A high flash point. High film strength, so the oil holds together under compression and clings to surfaces under centrifugal loads. A wide temperature range, typically quoted as about minus forty-five to plus one hundred and fifteen degrees. Low viscosity, possible because there are no reciprocating parts or heavy gears. And a high viscosity index, holding its viscosity as it warms.
Part 4 · Seals, oils, faults
Indications and classic faults Indication or symptom Meaning Action / note Oil pressure Measured after the pressure pump Low-pressure warning from the pressure gallery Oil temperature Measured as the oil leaves the (fuel-cooled) oil cooler High: suspect the cooler, e.g. blocked oil cooler air intake Oil quantity , filter ΔP, chip warningConsumption, blockage, bearing wear Debris: impending bearing failure Oil pump failure No lubrication Shut the engine down Internal engine overheat warningHot gas or air where it should not be Shut the engine down Short run-down time + high oil consumption Bearing chamber labyrinth seal rubbing Engineering inspection
Unlike a piston engine, a gas turbine cannot "limp on" without oil: the scavenge pumps cannot lubricate it and it cannot suck oil from the tank.
Chapter 20 · Gas Turbine Lubrication
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Finally, what the indications tell you. Oil pressure is measured after the pressure pump, and a low-pressure switch gives a warning. Oil temperature is measured as the oil leaves the oil cooler; a high oil temperature points at the cooling, for example a blocked air intake on an air-cooled oil cooler. Quantity, filter blockage and chip detector warnings tell of consumption, blockage and bearing wear. Some situations demand an immediate shut-down: failure of the oil pump, because the engine cannot run without lubrication, and an internal engine overheat warning. And a classic fault-finding question: if the run-down time after shut-down is short and the oil consumption is high, the most probable cause is a rubbing labyrinth seal on a bearing chamber.
Summary
What to take into the exam System Self-contained, recirculatory, dry sump, synthetic oil. Level checked shortly after shut-down.
Relief valve Valve opens at idle pressure: constant feed pressure at all speeds. Full flow: no valve, smaller pumps.
Pumps Gear type. One pressure + up to six scavenge (more capacity: aerated oil). No shear neck. Pump failure: shut down.
Coolers Air and/or fuel. FCOC: by-pass valve; oil pressure kept above fuel pressure. Temperature measured at cooler exit.
Chip detectors Magnets in the scavenge lines before the scavenge pumps: warn of bearing failure. Self-sealing.
Filters Suction (coarse), pressure (fine), last-chance thread, scavenge. ΔP switch or pop-up indicator.
Seals and breather Labyrinth seals pressurised by intermediate-stage air: minimum oil loss. Centrifugal breather minimises oil loss.
Faults High oil temp: cooler air intake blocked. Short run-down + high consumption: labyrinth seal rub. Internal overheat: shut down.
Chapter 20 · Gas Turbine Lubrication
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. Gas turbines use a self-contained, recirculatory, dry-sump system with synthetic oil, and the level is checked shortly after shut-down. In the relief-valve system the valve opens at the idle pressure, giving a constant feed pressure; the full-flow system has no valve and smaller pumps. The pumps are gear pumps, one pressure and up to six scavenge, with more scavenge capacity because the oil is aerated; there is no shear neck, and a pump failure means shut-down. In the fuel-cooled oil cooler, a by-pass valve protects against blockage and thick oil, and oil pressure is kept above fuel pressure. Chip detectors in the scavenge lines warn of bearing failure. Labyrinth seals are pressurised with intermediate-stage air, and the centrifugal breather keeps oil loss to a minimum.