Engines · Chapter 22
Performance and Thrust Augmentation How efficiently a gas turbine turns fuel into thrust, and how water, water–methanol and afterburning give more of it when it is needed.
turbine exhaust
afterburner
> 1 700 °C
water
methanol
reheat
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter twenty two is about performance and thrust augmentation. First we look at how well a gas turbine turns fuel into useful thrust: the constant pressure cycle it works on, its thermal efficiency, its propulsive efficiency and the specific fuel consumption that results, and how that changes with RPM and altitude. Then we ask how to get more thrust when we need it most, on a hot day at a high airfield, or for a combat take-off. The answers are water injection, water methanol injection, and afterburning, also called reheat.
Roadmap
Efficiency first, then more thrust 1 · Efficiency and SFC Constant-pressure cycle, thermal, propulsive and overall efficiency, SFC with RPM and altitude.
2 · Water and methanol Why hot and high hurts, thrust restoration and boost, injection methods, water–methanol.
3 · Afterburning Reheat jet pipe, flame holders, the variable nozzle, effects and fuel cost.
Chapter 22 · Performance and Thrust Augmentation
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This chapter has three parts. In part one we look at efficiency: the constant pressure cycle a gas turbine works on, what decides its thermal efficiency, how propulsive efficiency depends on the type of engine and the flight speed, and how the two together set the specific fuel consumption, which is lowest at high RPM and high altitude. In part two we deal with the hot and high problem and its classic cure, water injection, and see why it only restores thrust on a turbojet but can boost a turboprop above its normal power, and why methanol is added. Part three is afterburning, or reheat: burning extra fuel in the jet pipe, with flame holders and a variable nozzle, for a big gain in thrust at a heavy cost in fuel.
Part 1 · The cycle
The constant-pressure (Brayton) cycle
0
5
10
15
20
25
Volume (per unit mass) →
Pressure (bar)
1
2
3
4
combustion at constant pressure (2 → 3)
compression
expansion
exhaust
Brayton against Otto
Gas turbine
Combustion at constant pressure
continuous: all four at once, in different
places
Piston engine
Combustion at constant volume
intermittent: four strokes in one place
one after another
Computed for an ideal cycle: pressure ratio 25, compressor entry 288 K, turbine entry 1600 K.
Chapter 22 · Performance and Thrust Augmentation
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
A gas turbine works on the constant pressure cycle, sometimes called the Brayton cycle. The diagram is computed for an ideal engine with a pressure ratio of twenty five. From point one to point two the compressor squeezes the air, so pressure rises and volume falls. From two to three fuel burns, and the heat is added at constant pressure: the gas expands and its volume grows, but the pressure stays the same. From three to four the hot gas expands through the turbine and nozzle back to atmospheric pressure, and from four back to one the exhaust gives its heat away to the atmosphere, again at constant pressure. Compare the piston engine, which burns its charge at constant volume, in one cylinder, one stroke after another. In the gas turbine, all four processes happen continuously and at the same time, each in its own part of the engine. So jet engines employ a constant pressure combustion process.
Part 1 · The cycle
Why the pressure stays level in the combustor The combustion chamber is open at both ends : gas is free to expand rearwards So burning raises temperature and volume , and velocity, not pressure In practice pressure falls slightly (a few per cent) across the combustor The turbine then turns the hot gas energy into shaft work and the nozzle into velocity Continuous combustion: no power strokes , smooth and light for its power
Pressure along the engine
combustor
Pressure stays almost level while fuel burns
Chapter 22 · Performance and Thrust Augmentation
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why does the pressure stay level while fuel burns? Because the combustion chamber is open at both ends. In a piston engine, the charge is trapped by the valves and the piston, so when it burns its pressure shoots up. In the gas turbine, the gas is free to expand towards the turbine, so burning raises its temperature and its volume, and with them its velocity, but not its pressure. Look at the two traces under the engine: the pressure rises through the compressor and stays almost level through the combustion chamber, actually falling a few per cent because of friction and mixing, while the temperature soars. The turbine then turns some of that energy into shaft work to drive the compressor, and the nozzle turns the rest into a fast jet. Because combustion is continuous, there are no separate power strokes, so the engine is smooth and very light for its power.
Part 1 · Efficiency
Thermal efficiency Thermal efficiency : how much of the fuel's heat becomes useful gas energyFor the ideal cycle it depends only on the pressure ratio : η = 1 − 1/r0.286 5:1 gives about 37% ; 25:1 about 60% ; 40:1 about 65% Real engines also need a high turbine entry temperature to make the higher pressure ratio pay Cold intake air lets the same pressure ratio be reached with less work: efficiency improves at altitude
Ideal thermal efficiency
1
10
20
30
40
50
0%
20%
40%
60%
80%
Overall pressure ratio
5:1 → 37%
25:1 → 60%
40:1 → 65%
η = 1 − 1 / r^0.286 (ideal, γ = 1.4)
Real engines also need a high turbine entry temperature
Chapter 22 · Performance and Thrust Augmentation
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thermal efficiency tells us how much of the heat in the fuel becomes useful energy in the gas stream. For the ideal constant pressure cycle there is a neat result: it depends only on the pressure ratio. The curve is computed from that formula. An early jet with a pressure ratio of five to one could reach at best about thirty seven per cent; at twenty five to one the ideal figure is about sixty per cent; at forty to one, typical of a modern big fan, about sixty five per cent. Notice the diminishing returns. In a real engine, losses in the compressor and turbine mean that a high pressure ratio only pays if the turbine entry temperature is high too, which is why so much effort goes into turbine cooling and materials. And because cold air is easier to compress, the same engine runs more efficiently in the cold air at altitude.
Part 1 · Efficiency
Propulsive efficiency: each engine has its best speed
0
100
200
300
400
500
600
700
800
900
1000
0%
25%
50%
75%
100%
True airspeed (kt)
Propulsive efficiency
Curve peaks
A
A Turboprop
best near 265 kt
B
B High-bypass turbofan
best near 385 kt
C
C Low-bypass turbofan
best near 540 kt
D
D Turbojet
best near 930 kt
ηp = 2V / (V + Vj)
Stylised, computed from ηp = 2V/(V + Vj) with a high-speed loss for each type. Lower jet velocity gives higher efficiency, until propeller-tip or fan compressibility losses set in.
Chapter 22 · Performance and Thrust Augmentation
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
Propulsive efficiency measures how well the energy in the gas becomes useful work pushing the aircraft along. It is two V divided by V plus V j: the closer the jet velocity is to the flight speed, the less energy is left behind in the wake, and the higher the efficiency. So an engine that gently accelerates a large mass suits low speeds, and one that violently accelerates a small mass suits high speeds. Each curve rises, peaks, and then falls when losses such as propeller tip compressibility set in. Curve A, the turboprop, is best at the lowest speeds, up to about three hundred knots. Curve B, the high-bypass turbofan, peaks at typical airliner cruise speeds. Curve C, the low-bypass turbofan, peaks higher still, and curve D, the turbojet, only becomes efficient at very high speeds. In the exam, the curve that best represents a high-bypass turbofan is the second one, B.
Part 1 · Efficiency
Overall efficiency and SFC Overall efficiency = thermal × propulsive SFC is inversely proportional to overall efficiency (at a given flight speed) Turbojet: 51% × 45% ≈ 23% ; modern turbofan: 65% × 80% = 52% So the fan burns about 56% less fuel per unit of thrust Higher pressure ratio raises thermal efficiency; higher bypass ratio raises propulsive efficiency
Overall efficiency and SFC
Turbojet, PR 12
ηth 51% × ηp 45% = ηo 23%
Turbofan, PR 40, BPR 9
ηth 65% × ηp 80% = ηo 52%
SFC ∝ 1 / ηo: the fan burns 56% less fuel
per unit of thrust at the same flight speed
Chapter 22 · Performance and Thrust Augmentation
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
The two efficiencies multiply. Overall efficiency is thermal efficiency times propulsive efficiency, and specific fuel consumption is inversely proportional to it: double the overall efficiency and, at the same flight speed, you halve the fuel used for each pound of thrust. Let us compare two engines at airliner cruise speed. An old turbojet with a pressure ratio of twelve might have a thermal efficiency of fifty one per cent and a propulsive efficiency of forty five, so its overall efficiency is about twenty three per cent. A modern turbofan with a pressure ratio of forty and a bypass ratio of nine might reach sixty five and eighty per cent, an overall efficiency of fifty two per cent. It therefore burns about fifty six per cent less fuel for the same thrust. That is the story of jet engine development: a higher pressure ratio for the thermal side, a higher bypass ratio for the propulsive side.
Part 1 · SFC in service
SFC is lowest at high RPM and high altitude
50
60
70
80
90
100
0.4
0.8
1.2
1.6
RPM (% max)
SFC (relative)
sea level
20 000 ft
36 000 ft
lowest SFC: high RPM, high altitude
Reading the curves
SFC is high at low RPM: the
cycle pressure ratio is low.
It is lowest near high cruise
RPM (about 90–95%).
Cold air at altitude raises the
cycle efficiency, so SFC is
lower high up, to the tropopause.
Illustrative. At a given RPM, thrust and fuel flow fall together as height increases, so SFC changes only a little, but what change there is is an improvement , up to the tropopause.
Chapter 22 · Performance and Thrust Augmentation
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
How does specific fuel consumption change in service? At low RPM it is poor, because the compressor is producing only a low pressure ratio and the cycle is inefficient. As RPM increases, S F C falls, reaching its lowest value at high RPM, around ninety to ninety five per cent, near the engine's design point; right at the top it rises a little again. Altitude helps too. As we saw last chapter, thrust and fuel flow fall together as the aircraft climbs, so the S F C stays essentially the same. But the colder air at altitude makes the cycle a little more efficient, so the small change there is, is an improvement, all the way up to the tropopause. Put those together and the exam answer follows: the S F C of a jet engine is lowest at high RPM and high altitude. That is exactly why jets cruise high, at high RPM.
Part 1 · SFC in service
More fuel: thrust up, SFC either way Increasing fuel flow always increases thrust and N1 But SFC follows the curve: it may fall (low RPM) or rise (near maximum) Exam answer: thrust and N1 up, SFC might increase or decrease Cruise is set near the bottom of the curve for the best economy
More fuel: what happens to SFC?
50
60
70
80
90
100
0.4
0.8
1.2
1.6
RPM (% max) · y: SFC (relative)
A: SFC falls
B: SFC rises
Thrust and N1 always rise with fuel flow
SFC may rise or fall, depending on the RPM
Chapter 22 · Performance and Thrust Augmentation
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a question that catches people out. What happens when you increase the fuel flow? The thrust certainly increases, because the extra heat speeds up the turbines, the spools accelerate, as you can see, and the mass flow rises. N 1 increases too. But what about specific fuel consumption? That depends on where the engine was on its S F C curve. If it was at low RPM, at point A, adding fuel moves it towards the efficient region and the S F C falls. If it was already near maximum, at point B, adding fuel moves it up the far side of the curve and the S F C rises. So the correct answer is: thrust and N 1 increase, but the S F C might increase or decrease. Cruise power is chosen near the bottom of the curve to get the best economy.
Part 2 · Water injection
The hot and high problem Output depends largely on the mass of air through the engine At a high airfield and/or on a hot day , density and mass flow fall: less thrust or SHP Just when the aircraft needs it most: a long take-off run, a poor climb gradient Cure: cool the airflow with water to restore its density and mass Typically armed and activated by moving the throttle to the take-off position
into the intake
into the combustor
(most common)
1 Water evaporates and cools the gas
2 Cooler gas is denser: more mass flow
3 Mass through the turbine rises
4 Thrust or SHP is restored
Chapter 22 · Performance and Thrust Augmentation
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
The power of a gas turbine depends largely on the mass of air flowing through it. At a high airfield, or on a hot day, or worst of all both, the air is less dense, so the mass flow falls and so does the thrust or shaft horsepower. That happens just when the aircraft needs its power most, for a long take-off run and a safe climb gradient. The classic cure is to cool the airflow with water. As the water evaporates it absorbs heat, the gas becomes cooler and denser, and the mass flow, especially through the turbine, rises again. Water can be injected into the intake or, much more commonly, into the combustion chambers, as the scene shows. On a typical installation the system is armed before take-off and is activated when the throttle is moved to the take-off position.
Part 2 · Water injection
Thrust restoration and power boost
Turbojet: restoration
Turboprop: restoration and boost
-10
0
10
20
30
40
50
60
80
100
120
OAT (°C)
% rated
dry
with water: held at 100% (P3 max limit)
-10
0
10
20
30
40
50
60
80
100
120
OAT (°C)
dry
with water: up to +15%
restores lost thrust only
restores and boosts SHP
Illustrative curves. Turbojet: back to its flat-rated 100% to a higher temperature, but never above it. Turboprop: restored and boosted by up to about 15% .
Chapter 22 · Performance and Thrust Augmentation
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The two graphs show the difference between the engine types. On the left, a turbojet. Dry, its thrust is held at its flat-rated one hundred per cent up to a certain temperature, and then falls away as the day gets hotter. With water, the thrust is held at one hundred per cent up to a much higher temperature. But notice that it never goes above one hundred per cent: the water restores lost thrust, it does not boost it. On the right, a turboprop. Here the water not only restores the lost shaft horsepower but boosts it, by up to about fifteen per cent above the normal rating. Why the difference? It comes down to what limits each engine, and how the extra mass flow through the turbine is used. That is the next slide.
Part 2 · Water injection
Why a turbojet is restored but a turboprop is boosted Turbojet: extra mass flow could be had by raising compressor speed, but that raises P3 P3 max is limited to stop the casing splitting: a pressure sensor at the HP compressor outlet So a turbojet is restored only to its flat-rated 100% Turboprop with combustor injection: the extra turbine mass flow is not used to raise RPM or P3 Instead the blade angle coarsens at constant RPM: more air thrown back, SHP above 100%
Turbojet: P3 is the limit
Turboprop: the propeller absorbs it
More mass flow → higher compressor
delivery pressure P3
P3 max is fixed by casing strength:
a pressure sensor at the HP outlet
Result: restore to 100%, never above
Extra turbine mass flow is not used
to raise RPM (or P3)
Blade angle coarsens, RPM held:
more air thrown back per turn
Result: SHP above 100% (boost)
Chapter 22 · Performance and Thrust Augmentation
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
On a turbojet, you could get more mass flow by running the compressor faster, but that would raise the compressor delivery pressure, P three. The maximum value of P three is limited, because too much pressure could split the engine casing. A pressure sensor at the HP compressor outlet, part of the power limiter, holds it. So water can only restore a turbojet to its flat-rated one hundred per cent, never beyond. On a turboprop with water injected into the combustion chamber, the mass flow through the turbine increases relative to that through the compressor. That extra flow is not used to increase the compressor RPM, and so P three does not rise. Instead it is absorbed by coarsening the propeller blade angle, while the engine speed stays at no more than its normal maximum. The propeller throws more air backwards, and the shaft horsepower rises above one hundred per cent.
Part 2 · Water injection
Methods of injection Into the intake Into the combustion chamber Used on Some centrifugal engines and small early axial engines Most installations: by far the most popular Effect Cools the compressor inlet air: denser, more mass flow Raises turbine mass flow relative to compressor flow Problem Poor water distribution; quantity limited to avoid flame-out Cools the gas: TGT falls (cured by methanol) Result Thrust restored Smaller pressure drop needed across the turbine for its work: more energy left for a free turbine or jet pipe pressure
Chapter 22 · Performance and Thrust Augmentation
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two places to put the water. Some centrifugal compressor engines, and some small early axial engines, sprayed it into the intake. That cools the air entering the compressor, making it denser, but the water was not well distributed, and the quantity had to be limited so as not to put the flame out. By far the most popular method is injection into the combustion chamber. That increases the mass flow through the turbine relative to the flow through the compressor. The turbine has no extra work to do, since it still drives the same compressor, so it needs a smaller pressure drop across it to do that work. More energy is therefore left over, either to drive the propeller through a free turbine, or as extra jet pipe pressure for thrust. The drawback is that the water also cools the gas, which is where methanol comes in.
Part 2 · Water–methanol
Why add methanol? Pure water must all be used on take-off , or what is left freezes in the tanks in the climb Methanol is an alcohol: first job, anti-freeze Water cools the gas and lowers the TGT , which costs power (it is a heat engine) Methanol burns , adding heat and raising TGT back to its normal level: an important fuel too Typically 40% methanol, 60% water by volume, metered so TGT limits are not exceeded
Water–methanol, 60 : 40 by volume
40%
methanol
60%
water
Anti-freeze
left-over water would freeze
in the tanks at altitude
Burns
restores the TGT lost
to water cooling
Metered
a control system meters it so
TGT limits are not exceeded
Water alone: TGT falls, so some of the
possible power is lost (it is a heat engine)
Methanol: TGT back to its normal level
Chapter 22 · Performance and Thrust Augmentation
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Pure water has an obvious drawback. Any water left in the tanks after take-off would freeze as the aircraft climbed into cold air, so all of it had to be used up during the take-off. Adding methanol solves that: methanol is an alcohol, and its first job is to act as an anti-freeze. There is a bonus. Injecting water into the combustion chamber lowers the turbine gas temperature dramatically, and since a gas turbine is a heat engine, that takes away some of the power we were trying to gain. Methanol is itself a fuel. It burns, adding heat and bringing the turbine gas temperature back up to its normal level. So methanol is both an anti-freeze and an important source of fuel. The amount injected, and the ratio, must be carefully controlled; a typical mix of forty per cent methanol to sixty per cent water, by volume, ensures that the turbine temperature limits are never exceeded.
Part 2 · Water–methanol
Worked example: how much water? Early four-jet airliners carried about 300 US gallons per engine All used in a three-minute take-off and climb: 100 gal/min Fuel flow at the same time: 9000 lb/h ≈ 22 gal/min per engine Water flow is about 4.5 times the fuel flow Weight of water is the price: the system is used only when it is needed
Four-jet airliner, take-off and climb
Water carried per engine
300 US gal
Used in
3 minutes
Water flow
300 ÷ 3 = 100 gal/min
Fuel flow
9 000 lb/h
= 150 lb/min ÷ 6.7 lb/gal
≈ 22 gal/min
Water : fuel
100 ÷ 22 ≈ 4.5 : 1
All of it must be used up before the climb ends
Chapter 22 · Performance and Thrust Augmentation
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us put some numbers on it, using the big early four jet airliners, which used water injection. Each engine carried about three hundred US gallons of injection fluid, and all of it had to be used in a take-off and climb lasting about three minutes. Three hundred gallons in three minutes is one hundred gallons a minute. At the same time, each engine burned about nine thousand pounds of fuel an hour. Divide by sixty and that is one hundred and fifty pounds a minute, and at about six point seven pounds per gallon, roughly twenty two gallons a minute. So the water flowed at about four and a half times the rate of the fuel. That shows how much fluid is involved, and why the weight of the water is a real penalty. It is carried, and used, only when the take-off conditions demand it.
Part 3 · Afterburning
The afterburning jet pipe
Turbine exit
Diffuser: gas slowed
Fuel spray bars
Igniter / hot streak
Cooling liner: cooler gas along the walls
Flame holders (gutters)
Flame > 1 700 °C
Variable nozzle
Reheat burns fuel in the unused oxygen of the turbine exhaust, between the turbine and the propelling nozzle.
Chapter 22 · Performance and Thrust Augmentation
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Afterburning, also called reheat, takes advantage of the fact that the turbine exhaust still contains a lot of unused oxygen. Only part of the air is needed to burn the fuel in the main combustor; the rest is there to cool the gas for the turbine. So we can burn more fuel in the jet pipe, between the turbine and the propelling nozzle. Follow the gas from left to right. After the turbine, the exhaust cone and the widening duct form a diffuser, slowing the gas so that a flame can stay alight in it. Fuel spray bars inject atomised fuel. Flame holders, shaped like V gutters, create sheltered eddies that hold the flame in place. An igniter, or a hot streak of flame from the main combustor, lights it. A cooling liner keeps cooler gas along the walls, because the flame can exceed one thousand seven hundred degrees. At the end, a variable nozzle.
Part 3 · Afterburning
Keeping the flame alight and the pipe cool Gas leaving the turbine is too fast for a stable flame: it is diffused (slowed) first Flame holders create low-speed eddies where the flame anchorsSpray nozzles are centrally disposed , so cooler turbine gas flows along the jet pipe walls Lit by an igniter plug or a hot streak of flame from the main combustor The heated gas accelerates through the open nozzle: extra thrust
Flame holder close-up
jet pipe wall + cooling liner
cooler gas along the wall
diffused gas
fuel
slow eddies anchor the flame
V-gutter
Too fast and the flame blows out: the gas is
diffused first, and the gutters shelter the flame
Chapter 22 · Performance and Thrust Augmentation
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two problems have to be solved in a reheat jet pipe. The first is flame stability. The gas leaving the turbine is moving far too fast for a flame to stay alight; it would simply be blown out. So the gas is diffused, slowed down, before it reaches the afterburner, and the flame holders create small regions of slow, swirling gas where the flame can anchor itself. The exam phrase is that, on leaving the turbine, the gas stream is diffused to ensure the afterburning flame is stabilised. The second problem is heat. The fuel nozzles are placed centrally, around the axis of the flow, so that some of the relatively cool turbine exhaust flows along the jet pipe walls, helped by a perforated cooling liner. Once lit, by an igniter plug or a hot streak, the burning gas expands and accelerates through the open nozzle, giving additional thrust.
Part 3 · Afterburning
The variable propelling nozzle Afterburning greatly increases the volume of the gas The nozzle is closed for normal (dry) running and opens to pass the extra volume when afterburning Opening is automatic when afterburning is selected Selected by moving the throttle through a gate or detent Without it, back pressure would rise at the turbine: overheating and compressor surge
Dry: nozzle closed
Reheat: nozzle open
normal gas volume
hotter gas, more volume
Chapter 22 · Performance and Thrust Augmentation
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
When the afterburner lights, the gas in the jet pipe becomes much hotter, and its volume increases greatly. If the nozzle stayed the same size, it could not pass that extra volume, the pressure would build up behind the turbine, the turbine would overheat, and the compressor could surge. So an afterburning engine has a variable area propelling nozzle. It is closed for normal, non afterburning operation, and it opens to allow for the increased volume of gas during afterburning. The pilot does not operate it separately: it is controlled automatically, and it opens when afterburning is selected, typically by moving the throttle lever through a gate or detent beyond the normal maximum. The exam phrase: when afterburning, the jet pipe nozzle opens to allow for the increased volume of gas; and the variable nozzle opens automatically when afterburning is selected.
Part 3 · Afterburning
What afterburning changes Item With afterburning Why Thrust Increases greatly (typically +50% static, more at high speed)Hotter gas leaves the nozzle much faster Fuel consumption Increases dramatically; SFC roughly doublesHeat added at low pressure is used inefficiently EGT / jet pipe temperature Increases Flame in the jet pipe, over 1700 °C Pressure thrust Increases More gas energy at the choked nozzle exit Nozzle Opens Passes the larger volume of gas Use Take-off, climb, combat; short periods Military; the notable civil exception was Concorde
Chapter 22 · Performance and Thrust Augmentation
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what afterburning changes. Thrust increases a great deal, typically by about half at take-off and by much more at high speed. Fuel consumption increases dramatically, more than the thrust, so specific fuel consumption roughly doubles. That is because the heat is added at low pressure, after the turbine, where it is used inefficiently. The exhaust gas and jet pipe temperatures increase, with the flame above seventeen hundred degrees. Pressure thrust increases too, because there is more gas energy at the choked nozzle exit. So the correct set for an exam question is: fuel consumption increases, thrust increases, pressure thrust increases, and E G T increases. The nozzle opens. Because of the fuel cost, afterburners are used for short periods only: take-off, climb and combat on military aircraft. The notable civil exception was Concorde, with four low-bypass engines with afterburners.
Part 3 · Afterburning
Worked example: reheat thrust and fuel Dry: 80 kg/s × 600 m/s = 48 kN Reheat raises the jet temperature from 900 K to 2000 K; jet velocity ∝ √T 600 × √(2000/900) ≈ 894 m/s ; with 3% fuel mass, ≈ 74 kN , about +54% Fuel to heat 80 kg/s by 1100 K: ≈ 2.8 kg/s extra , nearly three times the dry flow SFC almost doubles : use it briefly
Reheat in numbers (static)
Dry
80 kg/s × 600 m/s
48 kN
Jet temperature
900 K → 2000 K
Jet velocity ∝ √T
600 × √(2000/900)
894 m/s
Reheat (+3% fuel mass)
82.4 kg/s × 894 m/s
74 kN
Thrust: +54%
Fuel flow: 1.5 → 4.3 kg/s (× 2.9)
SFC almost doubles: short periods only
Chapter 22 · Performance and Thrust Augmentation
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us estimate what reheat does, using simple numbers. Dry, our engine moves eighty kilograms a second at six hundred metres a second: forty eight kilonewtons static. Light the afterburner and the jet temperature rises from about nine hundred kelvin to two thousand. For the same nozzle pressure ratio, jet velocity goes with the square root of temperature, so it rises by the square root of two thousand over nine hundred, to about eight hundred and ninety four metres a second. Adding the fuel mass, about three per cent, thrust becomes about seventy four kilonewtons, roughly fifty four per cent more. Now the fuel. Heating eighty kilograms a second by eleven hundred degrees takes about two point eight kilograms of fuel a second, on top of perhaps one point five dry. So fuel flow nearly triples for about one and a half times the thrust, and the specific fuel consumption almost doubles.
Summary
What to take into the exam Cycle Constant-pressure (Brayton) combustion: continuous, chamber open at both ends.
Efficiency Thermal rises with pressure ratio; propulsive with lower jet velocity. Overall = thermal × propulsive; SFC ∝ 1/overall.
SFC Least at high RPM and high altitude . More fuel: thrust and N1 up, SFC up or down. High-bypass fan = curve B.
Water Restores mass flow hot/high. Turbojet: back to 100% only (P3 max, HP outlet sensor). Turboprop: boost ~15% by coarser pitch.
Methods Intake: poor distribution, flame-out risk. Combustor: most popular, more turbine mass flow.
Methanol Anti-freeze and a fuel: restores TGT. 40% methanol / 60% water by volume. 707: ≈ 4.5 : 1 water to fuel.
Reheat Burns spare oxygen after the turbine; gas diffused first; flame holders; flame >1700 °C; liner cooling.
Nozzle and effects Nozzle opens automatically on selection. Thrust, fuel flow, EGT and pressure thrust all increase.
Chapter 22 · Performance and Thrust Augmentation
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. A gas turbine burns its fuel at constant pressure, continuously, in a chamber open at both ends. Thermal efficiency rises with pressure ratio, propulsive efficiency rises as jet velocity approaches flight speed, overall efficiency is their product, and S F C is inversely proportional to it, lowest at high RPM and high altitude. Adding fuel raises thrust and N 1, but S F C may go either way. Water injection restores mass flow on hot and high days; a turbojet only gets back to one hundred per cent because of the P three limit, while a turboprop can be boosted by about fifteen per cent by coarsening the propeller. Methanol is an anti-freeze and a fuel, mixed forty to sixty. Reheat burns spare oxygen behind the turbine, after diffusing the gas, and its nozzle opens automatically; thrust, fuel flow, E G T and pressure thrust all increase.