Engines · Chapter 5
Piston Engine Ignition Dual ignition, how a magneto makes a 20 000 volt spark by itself, the ignition switch and its faults, the magneto checks, starting aids and keeping the system dry.
MAG
20 000 volts, at exactly the right moment
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter five is about ignition. Every time a cylinder is ready to fire, something has to put a spark of twenty thousand volts or more across the plug gap, at exactly the right moment, thousands of times a minute, and it must keep doing it even if the aircraft’s electrical system has failed completely. That something is the magneto. In this lesson we see why every aero engine has two independent ignition systems, how a magneto makes its own high voltage, what the capacitor, distributor and ignition switch do, how a broken wire can leave a propeller live, how to do the magneto checks, and how engines are helped to start.
Roadmap
From a spinning magnet to a spark in the right cylinder
Magneto
makes its own
electricity
Primary
few hundred
thick turns
Secondary
thousands of
thin turns
Distributor
half engine
speed
Spark plugs
two per
cylinder
Points open → primary current collapses → 20 000 V or more → spark in the right cylinder
1 · Dual ignition Two independent systems, two plugs per cylinder: safety and power.
2 · The magneto Magnet, coils, contact breaker, capacitor, distributor and timing.
3 · Switching and checks Why OFF means closed, P-lead faults, the dead cut and RPM drop checks.
4 · Starting and care Impulse coupling and booster coils, plugs and fouling, flashover, diesels.
Chapter 5 · Piston Engine Ignition
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the path we will follow. Along the top is the whole ignition chain. A magneto, driven by the engine, makes its own electricity in a primary coil of a few hundred thick turns. A secondary coil of thousands of thin turns steps that up to twenty thousand volts or more. A distributor, turning at half engine speed, sends each pulse to the right cylinder, where it jumps across the gap of a spark plug. Our lesson has four parts. First, why every aero engine has two complete ignition systems. Second, the magneto itself: the magnet, the coils, the contact breaker, the capacitor, the distributor and the timing. Third, how the ignition switch works, what happens when its wiring fails, and the checks you do before every flight. Finally, how engines are helped to start, spark plug fouling, moisture and flashover, and why a diesel needs no ignition system at all.
Part 1 · Dual ignition
Two independent ignition systems Every aero piston engine has dual ignition : two electrically independent systems Each cylinder has two spark plugs , fed by two separate magnetos Safety : a fault in one system does not stop the enginePower : two flame fronts burn the charge faster and more completelyThe magnetos need no battery : the engine keeps running after a total electrical failure
Looking down into the combustion chamber
Left mag
Right mag
Two flame fronts meet in the middle:
the charge burns in about half the distance,
so faster, more complete combustion and more power.
Either system alone can keep the engine running.
Chapter 5 · Piston Engine Ignition
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
All aero piston engines have dual ignition. That means two complete ignition systems that are electrically independent of each other. Each cylinder has two spark plugs, and each plug is fed by a different magneto, usually called the left and the right. There are two good reasons. The first is safety: if one magneto, one lead or one plug fails, the other system keeps the engine running. The second is power. Look at the picture. With two plugs, the charge is lit at two points, and the two flame fronts meet in the middle, so the flame only has to travel about half as far. The charge burns faster and more completely, which gives more power and makes detonation less likely. And because magnetos make their own electricity, the engine does not depend on the battery or the alternator: it keeps running even after a complete electrical failure.
Part 2 · The magneto
The magneto: generator and transformer in one A self-contained, engine-driven electrical generator A permanent magnet spins between pole shoes; its flux reverses through a soft-iron core The reversing flux generates alternating current in the primary coil: the magneto makes its own AC A secondary coil on the same core acts as a step-up transformer Result: extra high tension (EHT) sparks, delivered in the correct firing order
N
S
Coils on a soft-iron core
primary + secondary
Rotating permanent
magnet, engine-driven
Pole shoes carry the
reversing flux to the core
Generator + step-up transformer in one box:
self-contained, independent of the aircraft battery.
Chapter 5 · Piston Engine Ignition
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
A magneto is a self-contained electrical generator, driven by the engine, that makes the ignition sparks. Inside, a permanent magnet spins between two pole shoes. As it turns, its magnetic flux reverses through a soft-iron core, and that core carries two coils. The changing flux generates alternating current in the primary coil, so the magneto makes its own A C electricity; it needs no battery. The secondary coil, wound on the same core, turns the magneto into a step-up transformer as well, so it can produce the extra high tension needed to jump a plug gap. In the scene you can also see the cam and contact breaker, which interrupt the primary current twice every turn, the capacitor across the points, and the distributor, whose rotor sends each high-voltage pulse to the right plug. For the exam: a magneto is essentially an A C generator with a step-up transformer.
Part 2 · The magneto
The magneto circuit: primary and secondary
PRIMARY CIRCUIT (low tension)
SECONDARY CIRCUIT (extra high tension)
few hundred thick turns
thousands of thin turns
Contact
breaker
cam
Capacitor
Ignition switch
closed = OFF (primary earthed)
Distributor
rotor at half engine speed
cyl 1
cyl 3
cyl 2
cyl 4
HT leads in firing order
Points open → current in the primary collapses → huge voltage induced in the secondary → spark at the plug
The ignition switch is wired into the primary circuit, in parallel with the points; the capacitor is also in parallel with them.
Chapter 5 · Piston Engine Ignition
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole magneto circuit. On the left is the primary, or low tension, circuit: a coil of a few hundred turns of thick wire, the contact breaker points opened by a cam, and a capacitor connected in parallel with the points. The ignition switch is also in the primary circuit, wired from the primary to earth, in parallel with the points; that wire is often called the P-lead. On the right is the secondary, or extra high tension, circuit: thousands of turns of very thin wire on the same core, feeding the distributor rotor, which turns at half engine speed and passes each pulse along a high tension lead to a spark plug, in firing order. Each plug is earthed through the engine, so the spark jumps from the centre electrode to earth. The key event is the opening of the points, which we look at next.
Part 2 · Making the spark
The spark comes when the points open
0°
45°
90°
135°
180°
225°
270°
315°
360°
magnet rotation (degrees)
points open
points open
magnet flux in the core
primary current builds
SPARK: secondary
voltage leaps
Cam and distributor are geared together so that the rotor is lined up with the right plug lead just as the points open .
Chapter 5 · Piston Engine Ignition
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph shows one turn of a two-pole magnet. The dashed line is the magnet’s flux in the core, reversing twice a turn. While the contact breaker points are closed, the primary is a complete circuit, so a current builds up in it, and that current makes its own magnetic field. The cam is timed to open the points just as this primary current is near its peak. The moment the points open, the current is interrupted, its magnetic field collapses very quickly, and the lines of force sweep through the thousands of turns of the secondary coil. That induces a huge voltage, shown by the purple spike, which leaps across the plug gap as the spark. This is electromagnetic induction. So remember the exam answer: the spark occurs as the contact breaker points just open, not when they close. With a two-pole magnet, that happens twice per turn of the magnet.
Part 2 · Making the spark
Why the secondary voltage is so high Primary: a few hundred turns of thick wire ; secondary: thousands of turns of very thin wire Voltage is stepped up roughly by the turns ratio The fast collapse at the break gives a few hundred volts across the primary The secondary then reaches 20 000 volts or more To jump a gap you need a high EMF (voltage), not a high current
Turns ratio: a step-up transformer
N₁
N₂
Primary turns N₁
180
Secondary turns N₂
18 000
Ratio N₂ ÷ N₁
100 : 1
Primary voltage at break
about 250 V
Secondary voltage
250 × 100 ≈ 25 000 V
A spark needs high EMF (voltage), not high current.
Chapter 5 · Piston Engine Ignition
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why is the secondary voltage so high? Because the magneto’s coils form a step-up transformer. The primary has a few hundred turns of thick wire; the secondary has thousands of turns of very thin wire, and the voltage is multiplied roughly by the ratio of the turns. In the worked example there are a hundred and eighty primary turns and eighteen thousand secondary turns, a ratio of a hundred to one. When the points open, the rapid collapse of the field puts about two hundred and fifty volts across the primary, so the secondary sees roughly twenty-five thousand volts. That is what is needed, because air, and especially compressed air in a cylinder, is a good insulator. To push a spark across the electrode gap you need a high electromotive force, a high voltage. The current in the spark is tiny. An exam question may ask exactly that: a spark needs high E M F.
Part 2 · The capacitor
The capacitor (condenser) Fitted in parallel with the contact breaker points (and the ignition switch) As the points open, the capacitor absorbs the surge : only a tiny, weak spark at the points So it prevents arcing and burning of the contact breaker points And it makes the primary flux collapse rapidly , giving a stronger secondary voltage Burnt or pitted points point to a faulty capacitor
Without capacitor
arcing: points burn and pit
current dies away slowly
With capacitor
charge goes into the capacitor
current stops at once
0
25
50
75
100
time after the points open (microseconds, illustrative)
slow collapse: weak spark
rapid collapse: strong spark
primary current
Chapter 5 · Piston Engine Ignition
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The capacitor, also called the condenser, is fitted in parallel with the contact breaker points. Think about what would happen without it. As the points begin to open, the primary current does not want to stop, and the collapsing field tries to keep it going, so an arc jumps across the opening points. That arc burns and pits them, and because current keeps flowing through the arc, the field dies away slowly and the secondary voltage is weak. With a capacitor across the points, the surge goes into the capacitor instead. Only a tiny spark appears at the points, the primary current stops almost at once, and the flux collapses very rapidly, which gives a strong secondary voltage. So the capacitor does two jobs: it prevents arcing at the points and it speeds up the collapse of the primary field. If you find burnt contact breaker points, suspect a defective capacitor.
Part 2 · The distributor
The distributor: the right plug at the right time A rotary switch : the rotor arm passes a segment for each cylinder It directs the secondary (EHT) voltage to the spark plugs Plug leads are connected in the engine’s firing order In a four-stroke, rotor and cam turn at half engine speed Cam and rotor are geared so the spark comes as the points just open
1
3
2
4
Rotor arm
turns at half
engine speed
Segments
one per cylinder,
wired in firing
order 1-3-2-4
Four-stroke: each cylinder fires once every two
turns, so the rotor and cam turn at half engine speed.
Cam and rotor are geared: spark as the points just open.
Chapter 5 · Piston Engine Ignition
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
The distributor is a rotary switch inside the magneto. Its rotor arm receives the extra high tension from the secondary coil and, as it turns, it passes a segment for each cylinder. The plug leads are connected to the segments in the engine’s firing order, so each pulse goes to the cylinder that is ready to fire. Watch the flat four: its firing order is one, three, two, four, and the read-out lights each cylinder as its spark arrives. In a four-stroke engine every cylinder fires once in every two turns of the crankshaft, so the contact breaker cam and the distributor rotor turn at half engine speed. The cam and rotor are geared together so that the rotor is lined up with a segment at the very moment the points open. Exam point: the distributor directs voltage from the magneto’s secondary winding to the spark plugs.
Part 2 · Ignition timing
Ignition timing: the spark comes before TDC Burning takes time: the flame needs about two milliseconds to reach peak pressure Peak pressure should come at about 8–10° after TDC , when the crank can use it So the spark is timed before TDC : on a typical light engine about 20–25° BTDC Peak pressure at or before TDC would push against the rising piston: power lost, engine damaged At 2400 RPM the crank turns 14.4° every millisecond
TDC
BDC
spark ~25° BTDC
peak pressure
~8–10° ATDC
crank
At 2400 RPM the crank turns 14.4° every millisecond
(one degree ≈ 69 µs): a 2 ms burn spans about 29°.
Chapter 5 · Piston Engine Ignition
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Combustion is fast, but not instant. From the spark, the flame takes something like two milliseconds to burn through the charge and reach peak pressure. That peak should come at about eight to ten degrees after top dead centre, when the piston has just started down and the crank can turn the pressure into torque. So the spark has to be timed before top dead centre; on a typical light aircraft engine it is set at about twenty to twenty-five degrees before. The scene parks the piston at the moment of the spark, and the timing dial shows it at twenty-five degrees before T D C. Here is the arithmetic. At two thousand four hundred R P M the crank turns fourteen point four degrees every millisecond, so a two millisecond burn spans almost thirty degrees. If the peak came at or before top dead centre, it would push against the rising piston, wasting power and hammering the engine.
Part 2 · Ignition timing
Faster engine, earlier spark: advance with RPM
0
500
1000
1500
2000
2500
3000
0°
10°
20°
30°
40°
engine speed (RPM)
spark advance (degrees BTDC)
typical fixed light-aircraft timing (about 25° BTDC)
needed for peak pressure at ~9° ATDC
(burn time about 2 ms, constant)
1200 RPM: 5°
2400 RPM: 20°
2700 RPM: 23°
start: retarded to about TDC
Complex engines advance the ignition as RPM rises; most light-aircraft magnetos have fixed timing, retarded for starting .
Chapter 5 · Piston Engine Ignition
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The burn time stays roughly the same whatever the engine speed, but the faster the crank turns, the more degrees it moves during those two milliseconds. The red line shows the advance needed to keep peak pressure at about nine degrees after top dead centre. At twelve hundred R P M only about five degrees of advance is needed; at two thousand four hundred about twenty; at two thousand seven hundred about twenty-three. So in a complex engine, as R P M increases, the ignition timing is advanced. At low speeds, and above all when starting, the spark must be retarded, otherwise peak pressure arrives before top dead centre and the engine kicks back against the starter. Most light aircraft magnetos have a fixed timing, set for take-off and cruise power at about twenty-five degrees, and they use a starting device that retards the spark to about top dead centre.
Part 3 · The ignition switch
OFF means closed: how the switch works The ignition switch is wired into the primary circuit , between the primary and earth OFF : the switch is closed , earthing the primary and short-circuiting the pointsThe points can no longer break the current, so no spark ON : the switch is open : it breaks the primary-to-earth path, and the points control the primarySo the switch controls the magneto’s primary circuit , never the secondary
Switch OFF = switch CLOSED
points
ignition
switch
Primary short-circuited to earth:
points cannot break it, no spark
Switch ON = switch OPEN
points
ignition
switch
Points alone make and break
the primary: sparks as normal
Chapter 5 · Piston Engine Ignition
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
The ignition switch works the opposite way round to almost every other switch in the aircraft. It sits in the primary circuit, wired between the primary and earth, in parallel with the contact breaker points. In the OFF position the switch is closed. It connects the primary straight to earth, short-circuiting the points, so when the points open nothing changes: the current simply carries on through the switch, the field never collapses suddenly, and there is no spark. In the ON position the switch is open. It breaks that path to earth, and the points are left to make and break the primary as normal, so the magneto sparks. In other words, the magneto is made inoperative by earthing its primary circuit. The switch controls the primary circuit only; it is never connected to the secondary, the battery or the starter circuit.
Part 3 · The ignition switch
Switch positions on a typical light aircraft Position Left magneto Right magneto Notes OFF Earthed (off) Earthed (off) Both primaries earthed: no sparks R Earthed (off) Live Runs on the right magneto only: used for the checks L Live Earthed (off) Runs on the left magneto only: used for the checks BOTH Live Live Normal position for flight START (many types) Live (impulse coupling)Earthed (off) Starter engaged; spring returns to BOTH
“Live” means the switch is open for that magneto. A broken switch wire also leaves a magneto live: treat every propeller as live .
Chapter 5 · Piston Engine Ignition
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the positions of a typical light aircraft ignition switch. In OFF, both primaries are earthed, so neither magneto can spark. In R, the left magneto is earthed and only the right one is live; in L it is the other way round. These single positions are used for the magneto checks. BOTH is the normal position for flight, with both switches open and both magnetos live. Many types also have a START position, spring-loaded back to BOTH, which engages the starter motor; on many engines only the left magneto has an impulse coupling, so START leaves the left magneto live and earths the right one. Notice the logic again: live means the switch for that magneto is open. And because a magneto is made safe only by a good earth connection, a broken wire can leave it live. That is why you must always treat a propeller as live.
Part 3 · Faults
When the switch wire breaks or shorts Fault Effect while running How it shows up Switch wire (P-lead) broken or disconnected None : the magneto runs normallySelecting that magneto OFF gives no RPM drop ; the engine cannot be stopped with the switch: a live magneto Broken wire touches the engine or airframe That magneto is earthed, i.e. switched off Runs on one magneto: slightly rough, reduced power Switch for one magneto shorted to earth That magneto is permanently off RPM drop on BOTH; the engine stops when the other magneto is selected off in the check Faulty capacitor Weak sparks, misfiring Burnt, pitted contact breaker points
A magneto is switched off by earthing its primary . Lose the earth path and you lose the ability to switch it off.
Chapter 5 · Piston Engine Ignition
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the switch works by earthing the primary, its faults are easy to reason out. If the switch wire, the P-lead, breaks or comes disconnected, the earth path is lost, so that magneto is permanently live. The engine runs perfectly normally, so you would not notice in flight, but selecting that magneto off makes no difference, and the engine cannot be stopped with the switch. That is a live magneto, and anyone who moves the propeller could start the engine. If the broken wire then touches the engine or airframe, the primary is earthed again and that magneto is switched off. If the switch for one magneto is shorted to earth, that magneto is permanently off: the engine runs on the other one, a little roughly and with reduced power, and it stops when you select the good magneto off during the check. Finally, burnt contact breaker points suggest a faulty capacitor.
Part 3 · The checks
The dead cut check at slow running Done at slow running (idle), before any check at higher RPM Select each magneto off in turn : RPM must drop , but the engine must not stop A drop shows each magneto is live and can be switched off (no broken switch wire) It proves the pilot has control of the ignition before the high-power checks A separate “live magneto check” is not normally needed
Why the check is done at slow running
1
Unknown to the pilot, only one magneto
works
2
At high RPM the pilot selects the
good one OFF
3
The engine dies; the throttle is still
well open
4
Pilot snaps back to BOTH: the engine
bursts into life
5
Violent torque reaction: possible damage to the
engine and its mountings
Done first at idle, the same discovery is harmless:
each magneto OFF in turn, RPM must DROP
but the engine must NOT STOP.
Chapter 5 · Piston Engine Ignition
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The first ignition check is the dead cut check, done at slow running. You select each magneto off in turn, briefly. The R P M must drop, which tells you that the magneto you switched off really was working and really can be switched off. But the engine must not stop, which tells you the other magneto is working. Why do this at idle first? Imagine the engine is running on one magneto only, without the pilot knowing. During a high-R P M check the pilot switches that live magneto off, and the engine dies. The natural reaction is to snap the switch back to BOTH, and the engine bursts into life with the throttle well open, setting up a violent torque reaction between engine and airframe that can cause serious damage. Done first at idle, the same discovery is harmless. A separate live magneto check is not normally needed, because the dead cut check already shows it.
Part 3 · The checks
The magneto RPM drop check Done at about 75% of maximum RPM (the flight manual’s run-up RPM) Select L, back to BOTH, then R, back to BOTH, noting each RPM drop The drop is due to slower burning : only one plug per cylinder is firing Each drop, and the difference between them, must be within the manufacturer’s limits No drop : suspect a broken switch wire (live magneto). Too big or rough : plugs or magneto. Engine stops : the selected magneto is dead
1600
1650
1700
1750
1800
1850
time (seconds)
RPM
BOTH
L
BOTH
R
BOTH
−100
−125
Drops: L 100, R 125; difference 25 RPM.
Example limits (check your flight manual):
drop no more than about 150 RPM on either,
difference no more than about 50 RPM. Result: pass.
Chapter 5 · Piston Engine Ignition
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
The magneto R P M drop check is done at about seventy-five per cent of maximum engine speed, or whatever run-up R P M your flight manual gives. With the engine steady on BOTH, select L, back to BOTH, then R, and back to BOTH, noting each drop. Some drop is expected, because with one magneto off only one plug in each cylinder is firing, the charge takes longer to burn, and the engine makes slightly less power. In the example the drops are a hundred and a hundred and twenty-five R P M, a difference of twenty-five, comfortably inside typical limits of about a hundred and fifty on either and fifty between them. Now interpret the results. No drop at all suggests the other magneto did not switch off: a broken switch wire and a live magneto. A large drop or rough running points to a fouled plug or a magneto fault. And if the engine stops, the magneto you left on is dead.
Part 4 · Starting
Why starting needs help At cranking speed the magnet turns too slowly to make a strong spark And the normal timing, 20–25° BTDC, is far too early at cranking speed: the engine would kick back So starting needs a stronger and retarded spark Three aids: the impulse coupling , the HT booster coil and the LT booster coil Most light aircraft use the impulse coupling on one magneto
TDC
spark 25° BTDC
KICKBACK
Cranking at 100 RPM:
the crank turns only
0.6° per millisecond
A 2 ms burn spans
just 1.2°: peak pressure
arrives ~24° BEFORE TDC
and drives the piston
back down: the engine
tries to run backwards.
Starting needs a spark that is:
• stronger, despite the slow-turning magnet
• retarded, to about TDC
Chapter 5 · Piston Engine Ignition
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Starting raises two ignition problems. The first is spark energy. A magneto’s output depends on how fast its magnet turns, and when the engine is being cranked by the starter or by hand it turns far too slowly for the magneto to make a strong spark. The second is timing. The normal spark, twenty to twenty-five degrees before top dead centre, is set for running speeds. At cranking speed the crank barely moves while the charge burns, at a hundred R P M only about one degree in the two milliseconds of burning, so a spark that early would build its peak pressure well before top dead centre and kick the engine backwards, which can damage the starter or injure someone. The scene shows the answer: a spark retarded to about top dead centre. So starting needs a stronger spark, and a retarded one. There are three ways of providing them: the impulse coupling, the high tension booster coil and the low tension booster coil.
Part 4 · Starting
The impulse coupling
1 · Held
Engine turns slowly; a flyweight catches
a stop pin: the magnet is held still
while the coupling spring winds up
2 · Released
Near TDC the flyweight is lifted off
the pin: the spring flicks the magnet
round very fast: a late, hot spark
3 · Running
Above a few hundred RPM, centrifugal
force holds the flyweights clear:
normal drive, normal timing
Result for starting: a hot spark from a fast-turning magnet, and a RETARDED spark (about TDC), so the engine cannot kick back.
Purely mechanical: no pilot action and no battery needed. You hear it click as the engine is cranked.
After start, centrifugal force holds the flyweights clear, and the coupling drives the magnet normally.
Chapter 5 · Piston Engine Ignition
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The impulse coupling is a spring-loaded coupling between the engine drive and the magneto, and it is the most common starting aid on light aircraft. Look at the three stages. While the engine is cranked slowly, a flyweight on the coupling catches against a stop pin, so the magnet is held still while the engine keeps turning and a coil spring winds up. Near top dead centre, the flyweight is lifted off the pin and the spring flicks the magnet round very fast, which gives a hot spark, and because the magnet was held back, a retarded spark at about top dead centre, so the engine cannot kick back. Once the engine is running, centrifugal force holds the flyweights out of engagement, and the coupling simply drives the magnet. It is purely mechanical, needs no pilot action, and works even with a flat battery. You can hear it click as the engine is cranked.
Part 4 · Starting
Booster coils and the impulse coupling compared Starting aid How it works Pilot action Power source Impulse coupling Spring temporarily speeds up the magnet : strong, retarded spark None: automatic Mechanical: works with a flat battery HT booster coil Sends a stream of high-voltage pulses to the trailing (retarded) brush of the distributor rotor Switched ON for start, OFF after Needs a good battery LT booster coil Feeds low voltage into the magneto primary , so the magneto works normally at cranking speed Switched ON for start, OFF after Needs a good battery
Main advantage of the impulse coupling over a booster coil: it needs no electrical supply , so it still works when the battery is flat.
Chapter 5 · Piston Engine Ignition
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the three starting aids side by side. The impulse coupling we have just seen: a spring temporarily speeds up the magnet, giving a strong, retarded spark, with no action by the pilot and no electrical power needed. The high tension booster coil is an electrical device. During starting it sends a succession of high-voltage pulses to the trailing, or retarded, brush of the distributor rotor, so the starting spark is late as well as strong. It is switched on for starting and off once the engine is running. The low tension booster coil also needs the battery. It supplies a low voltage to the magneto’s primary circuit during starting, which allows the magneto to work normally even though it is turning slowly, and it too is switched on for the start and off afterwards. So the big advantage of the impulse coupling is that, being mechanical, it works even when the battery is flat.
Part 4 · Care of the system
Spark plugs and plug fouling The spark jumps from the centre electrode to the earthed body electrode HT leads are screened to stop radio interference Fouling : deposits bridge or short the gap, so the plug misfires Carbon fouling is most likely at low power : prolonged idling and low-power descents, rich mixturesA short run at higher RPM usually clears it; run at about 1000–1200 RPM before shut-down
Terminal: HT lead (screened)
Ceramic insulator
Threaded body (earth)
Electrodes and gap
Fouling: deposits short the gap; the plug misfires.
Carbon fouling is most likely at low power: long idling,
prolonged low-power descents, over-rich mixtures.
A short run at higher RPM usually burns it off.
Chapter 5 · Piston Engine Ignition
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
A spark plug carries the high voltage through a ceramic insulator to its centre electrode, and the spark jumps across the gap to the earthed electrode on the body. The high tension leads are screened, both to protect them and to stop the ignition from causing radio interference. Plugs can foul. That means deposits build up on the insulator and electrodes until they bridge or short the gap, so the plug misfires, which you would see as rough running and a bigger drop during the magneto check. Carbon fouling is most likely at low power: long periods of idling, prolonged low-power descents and over-rich mixtures, when the combustion chamber is too cool to burn the carbon away. Lead deposits from leaded fuel add to the problem. A short run at a higher R P M usually burns the deposits off, which is why many engines are run briefly at about one thousand to one thousand two hundred R P M before shut-down.
Part 4 · Care of the system
Moisture, flashover and carbon tracking Magnetos see sudden changes of temperature, so condensation forms Water is a conductor: the HT can flash over a wet surface to earth or to the wrong plug : misfiring Flashover can leave carbon tracking , a fine pencil-like line that keeps conducting when dry Coils, capacitors, distributors and rotors are waxed so water stands in separate beads Magnetos are vented , not hermetically sealed, because pressure and temperature change with altitude
Moisture beads
Flashover path
to the wrong plug
or to earth
Waxed parts make water stand in separate beads.
A burnt pencil-line of carbon (carbon tracking) can
keep conducting even after it dries.
Magnetos are vented, not sealed: they breathe with altitude.
Chapter 5 · Piston Engine Ignition
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Magnetos and distributors are exposed to rapid changes of temperature, so moisture can condense inside them. Water conducts electricity, so if a film of it forms on an insulating part such as the distributor block or rotor, the high voltage can flash across the wet surface instead of across the air gap it is supposed to jump. It may go to earth, or to the wrong spark plug. This is called flashover, and it causes misfiring. Worse, the spark burns dirt particles that contain hydrocarbons, leaving a fine pencil-like line of carbon called carbon tracking. That line keeps conducting even when the moisture has gone. To fight this, coils, capacitors, distributors and rotors are waxed, so that water stands in separate beads and cannot form a continuous path. You might think the answer is to seal the magneto completely, but it cannot be hermetically sealed, because pressure and temperature change with altitude; instead magnetos are vented.
Part 4 · Diesels
Diesels: compression ignition, no spark A diesel is a compression-ignition engine: it needs no ignition system , saving weight and complexity Very high compression ratios (up to about 25 : 1 ) heat the air far above the fuel’s self-ignition temperature Fuel is injected into this hot air and ignites by itself For cold starts, glow plugs (pre-heaters) warm the combustion chamber Once running, ignition is continuous as long as fuel is injected
Air temperature after compression
T₂ = T₁ × r^(γ − 1), starting from 15 °C, γ = 1.4
≈ 405 °C
8.5 : 1
≈ 600 °C
16 : 1
≈ 771 °C
25 : 1
petrol engine
diesels
diesel fuel
self-ignites ~250 °C
Fuel injected into air this hot ignites by itself: no spark needed.
(Illustrative: real compression is not perfectly adiabatic.)
Chapter 5 · Piston Engine Ignition
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aero-diesels are becoming common, and they do not need an ignition system at all, which saves weight and complexity. A diesel is a compression-ignition engine. Its compression ratio is very high, up to about twenty-five to one, and squeezing air that hard heats it enormously. The bar chart works it out for perfect, adiabatic compression from fifteen degrees: about four hundred degrees at eight and a half to one, a typical petrol engine; about six hundred at sixteen to one; and about seven hundred and seventy at twenty-five to one. Diesel fuel ignites by itself at roughly two hundred and fifty degrees, so when it is injected into air that hot it simply lights. When the engine is cold, the walls soak up heat and the air may not get hot enough, so glow plugs, also called pre-heaters, warm the combustion chamber for starting. Once the engine is running, combustion continues by itself as long as fuel is injected.
Summary
What to take into the exam Dual ignition Two independent systems, two plugs per cylinder: safety, plus faster burning and more power.
Magneto Self-contained, engine-driven: AC generator + step-up transformer . No battery needed.
The spark When the points open : primary flux collapses, EHT induced in the secondary. Needs high EMF.
Capacitor In parallel with the points: prevents arcing , speeds the collapse. Burnt points = bad capacitor.
Distributor Secondary to the plugs in firing order; rotor and cam at half engine speed . Advance with RPM.
Switch In the primary . OFF = closed = earthed. Broken P-lead = live magneto , cannot switch off.
Checks Dead cut at slow running: drop but no stop. RPM drop at ~75% max: within limits.
Starting Impulse coupling : spring speeds the magnet, retarded spark, centrifugal disengage. HT/LT boosters need a battery.
Chapter 5 · Piston Engine Ignition
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather it up. Every aero engine has dual ignition: two independent systems and two plugs per cylinder, for safety and for faster burning. A magneto is a self-contained, engine-driven A C generator with a step-up transformer, so it needs no battery. The spark comes when the contact breaker points open, collapsing the primary flux and inducing extra high tension in the secondary; a spark needs a high E M F. The capacitor, in parallel with the points, prevents arcing and speeds the collapse. The distributor sends the secondary voltage to the plugs in firing order, turning at half engine speed, and complex engines advance the timing with R P M. The ignition switch is in the primary: OFF means closed and earthed, and a broken P-lead leaves a live magneto. The dead cut check is at slow running, the R P M drop check at about seventy-five per cent. And the impulse coupling gives a strong, retarded starting spark without any battery.