Engines · Chapter 1
Engine Principles and Types How an engine turns the chemical energy of fuel into a turning shaft, the physics you need for the rest of the course, and the main types of aero engine.
CHEMICAL fuel + air HEAT combustion PRESSURE on the piston MECHANICAL turning shaft
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Welcome to the Engines course, and to chapter one, engine principles and types. Every aero engine, from the little four-cylinder in a trainer to the turbofan on an airliner, does the same basic job: it takes the chemical energy locked in fuel, releases it as heat, and turns that heat into useful mechanical work. In this first lesson we build the toolkit you will use for the rest of the course: force, work, energy and power, Newton's laws, the two laws of thermodynamics, Bernoulli and the venturi, and the gas laws. Then we apply them to the cylinder and take a first look at diesels and gas turbines.
Roadmap
The physics behind every aero engine
1 Engines what they are and the main families 2 Mechanics force, work, energy, power 3 Laws Newton and thermodynamics 4 Flow Bernoulli, continuity, the venturi 5 Gases Boyle, Charles, the combined law 6 Applied the cylinder, diesels, gas turbines
Why it matters Every later chapter (carburettors, superchargers, compressors, nozzles) uses these ideas.
Exam style Expect definitions, units, simple calculations and duct trends: pressure, velocity, temperature .
Working fluid Remember throughout: air is the working fluid . Fuel only adds the energy.
Chapter 1 · Engine Principles and Types
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has six steps. First, what an engine is and the main families of engine you will meet. Second, the mechanics: force, work, energy and power, with a worked example that takes us all the way to horsepower. Third, Newton's three laws and the two laws of thermodynamics. Fourth, air in motion: Bernoulli's theorem, the continuity equation and the venturi. Fifth, the gas laws of Boyle and Charles and the combined gas law. Finally, we apply all of that to the cylinder and take a first look at diesels and gas turbines. Keep one idea in mind throughout: air is the working fluid of every engine in this course. The fuel only supplies the energy; it is the air that is squeezed, heated and expanded to do the work.
Part 1 · Engines
From steam to internal combustion Early powered flight was held back by the lack of a light, powerful engine The steam engine is external combustion : fuel burns under a boiler, outside the cylinder; heavy, and much heat is wasted The four-stroke principle was described by Beau de Rochas ; Nikolaus Otto built the first successful working engine in 1876 Internal combustion : the fuel burns inside the cylinder, so the gas that is heated is the gas that does the workEvery engine converts heat energy into mechanical energy
External combustion Internal combustion fire outside boiler water → steam cylinder Steam engine heavy · much heat wasted Piston engine burns fuel inside the cylinder
Chapter 1 · Engine Principles and Types
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Early pioneers had the aerodynamics more or less worked out long before they had an engine light and powerful enough to fly. The steam engine of the day was an external combustion engine. Fuel burned under a boiler, the boiler made steam, and the steam was piped to a cylinder. That meant a heavy boiler, a lot of water, and a great deal of heat simply escaping to the atmosphere. The answer was internal combustion. The four-stroke principle was described by the French engineer Beau de Rochas, and Nikolaus Otto built the first successful working engine in eighteen seventy-six, which is why the four-stroke cycle is still called the Otto cycle. In an internal combustion engine the fuel burns inside the cylinder itself, so the gas that is heated is the very gas that pushes the piston. That is far more compact, and it is the basis of every piston aero engine.
Part 1 · Engines
The basic principle of the piston engine A mixture of air and fuel is drawn into the cylinder The piston compresses it; a spark ignites it The rapid temperature rise raises the gas pressure , which forces the piston down The connecting rod and crankshaft turn the piston's straight-line motion into rotation The burnt gases are then exhausted : one power stroke every two turns of the crank
Spark plug ignites the mixture Inlet valve Hot gas pressure pushes the piston Piston moves in a straight line Connecting rod Crankshaft turns: rotary motion force
Chapter 1 · Engine Principles and Types
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole idea of the piston engine in one cylinder. A mixture of air and fuel is drawn into the cylinder. The piston rises and compresses it, and then a spark from the spark plug ignites it. The burning mixture gets very hot very quickly, and because it is trapped, its pressure rises sharply. That pressure acts on the crown of the piston and forces it down the cylinder. The connecting rod joins the piston to an offset crank on the crankshaft, so the straight-line motion of the piston is turned into rotation, which drives the propeller. Finally the piston rises again and pushes the burnt gases out through the exhaust. Watch the read-out as the strokes go by: induction, compression, power and exhaust. Only one of the four does useful work, and the whole cycle takes two complete turns of the crankshaft.
Part 1 · Engines
The main engine families Four-stroke spark ignition The Otto cycle: valves, a spark, one power stroke every two turns. Most light aircraft; the subject of this course.
Two-stroke spark ignition Ports in the cylinder wall instead of valves; a power stroke every turn . Light and simple: microlights.
Compression ignition (diesel) Air alone is compressed until it is hot enough to ignite fuel injected into it. No spark.
Wankel rotary A triangular rotor turning in a shaped housing: no pistons going up and down. Rare in aviation.
Gas turbine Compressor, combustion chamber and turbine working continuously : turbojet, turbofan, turboprop, turboshaft.
How piston engines are classified Cylinder layout, drive (direct or geared), rotation, capacity, cooling, fuel system, and normally aspirated or supercharged.
Chapter 1 · Engine Principles and Types
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Internal combustion engines come in several families. The four-stroke spark ignition engine, working on the Otto cycle, is the one in almost every light aircraft, and it is the main subject of the piston part of this course. A two-stroke engine uses ports in the cylinder wall instead of valves and gives a power stroke every revolution, so it is light and simple; you find it on microlights. The compression ignition engine, the diesel, has no spark at all: it squeezes air so hard that the air becomes hot enough to ignite fuel injected into it. The Wankel rotary engine uses a triangular rotor instead of pistons and is rare in aviation. The gas turbine does the same jobs as a piston engine but continuously, in separate components. And piston engines are classified by cylinder layout, type of drive, direction of rotation, capacity, cooling, fuel system and whether they are supercharged.
Part 2 · Mechanics
Force and work Force starts, stops or changes the motion of a body: F = m × a ; units newtons or pounds force In the cylinder: force = gas pressure × piston area Work done = force × distance moved in the direction of the force; units joules or foot-pounds The force on the piston does work as it moves the piston down the stroke No movement, no work: a force that moves nothing does no work
Worked example Mean gas pressure 150 psi Piston area 20 in² Force = p × A 3 000 lbf Distance moved (stroke) 0.4 ft Work = F × d 1 200 ft·lbf per power stroke, in each cylinder
Chapter 1 · Engine Principles and Types
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
A force is whatever starts a body moving, stops it, or changes the direction of its motion. Newton gave us its size: force equals mass times acceleration, measured in newtons, or in pounds force in the imperial units still used for many piston engines. In the cylinder the force comes from gas pressure acting on the crown of the piston, so force equals pressure times area. Work is done when a force moves something: work equals force times the distance moved in the direction of the force, in joules or foot-pounds. Let us put numbers on it. Suppose the mean gas pressure is one hundred and fifty pounds per square inch and the piston area is twenty square inches. The force is three thousand pounds. If the piston moves zero point four of a foot down its stroke, the work done is one thousand two hundred foot-pounds, in each cylinder, on every power stroke.
Part 2 · Mechanics
Energy: it changes form, it is never lost Energy is the capacity to do work; units joules Forms: chemical, heat, light, kinetic, potential , pressure Conservation of energy : energy cannot be created or destroyed, only changed in formIn the engine: chemical (fuel) → heat (combustion) → mechanical (crankshaft) Most of the heat is not turned into work: a good piston engine has a thermal efficiency of only about 25–28 %
Where the fuel energy goes (typical round figures) Thermal efficiency ≈ 25–28 % fuel energy 100% 25% Useful work at the shaft 5% Friction in the engine 30% Heat to cylinders, oil, cooling air 40% Heat out of the exhaust
Chapter 1 · Engine Principles and Types
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Energy is the capacity of a body to do work, and it is measured in joules, the same unit as work. It comes in many forms: chemical, heat, light, kinetic energy of motion and potential energy of position. The law of conservation of energy says that energy can be neither created nor destroyed; it can only change from one form to another. An engine is a chain of such changes. The chemical energy in the fuel is released as heat by combustion, the heat raises the pressure of the gas, and the engine turns that into mechanical energy at the crankshaft. Sadly, most of the heat never becomes useful work. In round figures, of every hundred units of fuel energy, about forty leave in the exhaust, about thirty go into the cylinders, oil and cooling air, around five are lost to friction, and only about a quarter reach the propeller.
Part 2 · Mechanics
Power: how fast the work is done Power = work done ÷ time : the rate of doing workSI unit: the watt (1 joule per second) Imperial unit: the horsepower = 33 000 ft·lbf per minute = 550 ft·lbf per second 1 hp ≈ 746 W (often rounded to 750 W)More power: more work per stroke, more cylinders, or more strokes per minute (higher RPM )
1 horsepower = 33 000 ft·lbf per minute 1 lb 33 000 ft in 1 min = 550 ft·lbf per second ≈ 746 watts (≈ 750 W is a fair exam rounding) Continuing the example: four cylinders at 2 400 RPM Each cylinder fires once every two turns: 4 × 2 400 ÷ 2 = 4 800 power strokes a minute 1 200 ft·lbf × 4 800 = 5 760 000 ft·lbf per minute ÷ 33 000 = 174.5 horsepower × 0.746 ≈ 130 kW This is power inside the cylinders (indicated power), before friction.
Chapter 1 · Engine Principles and Types
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
Power is the rate of doing work: how much work is done each second or each minute. The SI unit is the watt, one joule per second. Piston engines are still usually rated in horsepower. James Watt reckoned that a good horse could raise one pound through thirty-three thousand feet in a minute, so one horsepower is thirty-three thousand foot-pounds per minute, or five hundred and fifty foot-pounds per second, which is about seven hundred and forty-six watts. Let us finish our example. Each cylinder does one thousand two hundred foot-pounds per power stroke. A four-cylinder engine at two thousand four hundred RPM makes four thousand eight hundred power strokes a minute, because each cylinder fires once every two turns. That is five point seven six million foot-pounds per minute. Divide by thirty-three thousand and you get about one hundred and seventy-five horsepower, or about one hundred and thirty kilowatts.
Part 3 · Laws of motion
Newton's first law: inertia in the engine First law : a body stays at rest, or moving steadily in a straight line, unless a force acts on itThis reluctance to change is inertia ; it has no units The mixture does not want to start flowing : the inlet valve opens before TDC Once moving, the column keeps flowing : the inlet valve closes after BDC The piston, rod and crank do not want to stop either: the flywheel effect carries them through the idle strokes
TDC BDC opens 20° early mixture must start moving closes 55° late moving column keeps flowing INLET VALVE open for 255° of crank rotation
Chapter 1 · Engine Principles and Types
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Newton's first law says that a body stays at rest, or keeps moving at a steady speed in a straight line, unless a force acts on it. That reluctance to change is called inertia, and it matters a great deal inside an engine, because air and mixture are bodies too. The mixture in the induction pipe does not want to start flowing, so designers open the inlet valve a little before top dead centre, giving it a head start. Watch the timing dial: the piston parks just before the top with the inlet valve already opening. Then, once the column of mixture is moving fast, it does not want to stop, so it keeps flowing in even after the piston has passed bottom dead centre and started to rise. The inlet valve is therefore closed late, after bottom dead centre. The same inertia, in the piston and crankshaft, carries the engine through its three idle strokes.
Part 3 · Laws of motion
Newton's second and third laws Second law : acceleration is proportional to the force and inversely proportional to the massMomentum = mass × velocity (kg·m/s); the second law is the momentum law Gas pressure accelerates the piston: control the pressure and you control the force Third law : every action has an equal and opposite reaction Examples: a gun recoils, a hose snakes, a propeller and a jet engine push air back and are pushed forward
1st law · inertia A body stays at rest, or moving steadily, unless a force acts 2nd law · momentum Acceleration ∝ force ÷ mass; momentum = mass × velocity 3rd law · reaction Every action has an equal and opposite reaction Mixture: reluctant to start flowing Piston: reluctant to stop at TDC and BDC m F a = F ÷ m momentum: kg·m/s gas thrown back thrust: the reaction
Chapter 1 · Engine Principles and Types
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Newton's second law says that the acceleration of a body is proportional to the force on it and inversely proportional to its mass. Double the force and you double the acceleration; double the mass and you halve it. A moving mass has momentum, mass times velocity, measured in kilogram metres per second, so the second law is often called the momentum law. In the engine, the energy released by combustion raises the gas pressure, and that pressure accelerates the mass of the piston; controlling the pressure controls the force. Newton's third law says that for every action there is an equal and opposite reaction. A gun recoils as the bullet leaves, and a hose snakes as water is forced out of its nozzle. Propellers and jet engines work the same way: they accelerate a large mass of air backwards, and the reaction pushes the aircraft forwards.
Part 3 · Heat
The two laws of thermodynamics Thermodynamics : how gases behave as their temperature and pressure changeFirst law : heat and mechanical energy are mutually convertible at a constant, measurable rateRubbing dry surfaces turns work into heat; an engine turns heat into work Second law : heat will not flow from a colder to a hotter region without energy from outside A radiator loses heat freely to cold air; a refrigerator needs power to pump heat out
First law: heat ⇄ work at a fixed rate rubbing: work → heat engine: heat → work 778 ft·lbf = 1 BTU 4.19 J = 1 calorie The exchange rate never changes and can be measured Second law: heat flows only downhill by itself HOT COLD free needs work Radiator: heat leaves freely Refrigerator: needs energy from outside to pump heat from cold to hot
Chapter 1 · Engine Principles and Types
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
Thermodynamics is the study of heat and pressure energy: how gases behave as their temperature and pressure change. Its first law says that heat and mechanical energy can be converted into each other, and that the rate of exchange is fixed and can be measured. Rub two dry surfaces together and the work you do appears as heat; burn fuel in an engine and some of the heat appears as work. In imperial units, seven hundred and seventy-eight foot-pounds of work are equivalent to one British thermal unit of heat. The second law says that heat will not flow from a colder region to a hotter one without energy being supplied from outside. Heat flows naturally from a hot radiator into the colder air around it, but a refrigerator needs a motor and electrical power to pull heat out of its cold interior and dump it into the warmer kitchen.
Part 4 · Flow
Bernoulli's theorem A moving fluid has potential (height), pressure and kinetic energy In steady, streamline flow of an ideal fluid their sum is constant For air, height changes are negligible: pressure energy + kinetic energy = constant So where the air speeds up , its static pressure falls , and vice versa Basis of the venturi , the carburettor and many instruments
throat: fastest, lowest pressure position along the duct total energy: constant pressure energy kinetic
Chapter 1 · Engine Principles and Types
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Daniel Bernoulli, a Swiss scientist of the eighteenth century, showed that a moving fluid carries three kinds of energy: potential energy because of its height, pressure energy, and kinetic energy because of its motion. In the steady, streamline flow of an ideal fluid, the sum of the three stays constant. For air flowing through an engine the changes in height are tiny, so we can drop the potential term and say that pressure energy plus kinetic energy is constant. That gives the key result. Wherever the air speeds up, its static pressure must fall, and wherever it slows down, its pressure rises again. Watch the glass columns on the tube: in the slow air at the inlet the column stands high, and at the throat, where the air is fastest, the static pressure is lowest. This one idea explains the venturi, the carburettor, and a good deal of what happens in a gas turbine.
Part 4 · Flow
Constant mass flow: the continuity equation In steady flow, the mass of air passing any section each second is the same Mass flow = density × area × velocity = constantAt low speed density hardly changes, so area × velocity is constant Narrow the duct and the air must speed up ; widen it and it slows Then Bernoulli tells us the pressure: fast air, low pressure
A₁ = 100 cm² V₁ = 30 m/s A₂ = 50 cm² V₂ = 60 m/s mass flow = ρ × A × V = constant Low speed: density almost unchanged, so A × V is constant Half the area → twice the speed: 100 × 30 = 50 × 60 Bernoulli: pressure drop = ½ ρ (V₂² − V₁²) = 0.5 × 1.225 × (3 600 − 900) ≈ 1 650 Pa (16.5 hPa) Faster air at the throat → lower static pressure there
Chapter 1 · Engine Principles and Types
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Bernoulli tells us what happens to pressure when the speed changes, and the continuity equation tells us why the speed changes in the first place. In steady flow, air cannot pile up or vanish inside a duct, so the mass of air passing every cross-section each second must be the same. Mass flow equals density times area times velocity, and that product is constant. At the low speeds in a carburettor the density hardly changes, so simply area times velocity is constant. Here is an example. Air enters a duct of one hundred square centimetres at thirty metres per second. The duct narrows to fifty square centimetres, so to pass the same mass the air must double its speed to sixty metres per second. Bernoulli then gives the pressure drop: a half times the density times the difference of the speeds squared, which comes to about one thousand six hundred and fifty pascals.
Part 4 · Flow
The venturi: a convergent–divergent duct
convergent throat divergent (longer) position along the venturi velocity static pressure temperature
Convergent (subsonic): velocity ↑, pressure ↓, temperature ↓. Divergent : velocity ↓, pressure ↑, temperature ↑. Mass flow is the same throughout.
Chapter 1 · Engine Principles and Types
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
A venturi tube is a convergent-divergent duct: an inlet that narrows smoothly to a throat, followed by a longer outlet section that widens again. As the air enters the convergent part, continuity makes it speed up, and Bernoulli makes its static pressure fall. Its temperature falls too, because some of the heat energy of the air has become kinetic energy. At the throat the speed is highest and the pressure and temperature are lowest. In the divergent part everything reverses: the air slows down, and its pressure and temperature rise again. The divergent section is made longer and gentler so the air can slow down smoothly without breaking away from the walls. Learn the exam trends exactly as they appear in the caption, for subsonic flow. Convergent duct: velocity up, pressure down, temperature down. Divergent duct: velocity down, pressure up, temperature up.
Part 4 · Flow
The venturi at work: the carburettor The carburettor barrel contains a venturi ; air for the engine flows through it At the throat the air is fast and its pressure is below atmospheric The float chamber is vented to atmosphere , so the higher pressure there pushes fuel out of the nozzle More air flow → bigger pressure drop → more fuel : the fuel is metered by the air The temperature drop in the venturi, plus fuel evaporation, can cause carburettor ice
air in float chamber, vented mixture to engine Venturi throat fast air, low pressure Fuel is pushed out of the nozzle by the higher chamber pressure
Chapter 1 · Engine Principles and Types
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The most important use of the venturi in a piston engine is the carburettor, which you will study in detail later. All the air the engine breathes flows through a venturi in the carburettor barrel. At the throat the air is fast, so its static pressure is below atmospheric. Fuel waits in a float chamber that is vented to the atmosphere, so the pressure on the fuel there is higher than at the throat, and that difference pushes fuel out of a nozzle into the air stream as a spray. Watch what happens when the throttle opens: more air flows, the throat gets faster, the pressure columns show a bigger drop, and more fuel is drawn in. In other words the fuel is metered by the air. Remember too that the air also cools in the venturi, and evaporating fuel cools it further; that is the root of carburettor icing.
Part 5 · Gas laws
Boyle's law: pressure and volume At constant temperature , the volume of a gas is inversely proportional to its pressure P × V = constant (P is absolute pressure)Halve the volume → double the pressure; quarter it → four times the pressure Use absolute pressure: gauge pressure + atmospheric pressure In a real cylinder the gas also heats up as it is squeezed, so the pressure rises more than Boyle predicts
0.125 0.25 0.5 1 1 2 4 8 volume (litres) absolute pressure (bar) 1 L × 1 bar 0.5 L × 2 bar 0.25 L × 4 bar 0.125 L × 8 bar P × V = constant = 1 bar·litre Halve the volume → double the pressure (temperature held constant)
Chapter 1 · Engine Principles and Types
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Robert Boyle found that if you keep the temperature of a gas constant, its volume is inversely proportional to its pressure. Written as a formula, pressure times volume is a constant. On the graph, one litre of gas at one bar becomes half a litre at two bar, a quarter litre at four bar and an eighth of a litre at eight bar; the product is always the same. So if the volume is halved, the pressure is doubled. Two cautions for the exam. First, the pressure in the gas laws must be absolute pressure, which is gauge pressure plus atmospheric pressure, never gauge pressure alone. Second, Boyle's law assumes the temperature does not change. In a real engine the gas is compressed so quickly that it heats up, so the pressure at the end of the compression stroke is much higher than Boyle alone would predict. We will see how much in two slides.
Part 5 · Gas laws
Charles's law: volume and temperature At constant pressure , the volume of a gas is directly proportional to its absolute temperature V ÷ T = constant , with T in kelvin (°C + 273)Double the absolute temperature → double the volume Example: 1 litre at 15 °C (288 K) becomes 2 litres at 576 K (303 °C), not at 30 °C Also called Gay-Lussac's law
-273 15 303 0 1 2 temperature (°C) volume (litres) 15 °C = 288 K: 1 L 303 °C = 576 K: 2 L absolute zero V ÷ T = constant (T in kelvin, pressure held constant) Double the absolute temperature → double the volume
Chapter 1 · Engine Principles and Types
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Charles's law, also known as Gay-Lussac's law, deals with temperature. If a gas is held at constant pressure, its volume is directly proportional to its absolute temperature. So volume divided by absolute temperature is a constant. The word absolute is the trap. Temperatures in the gas laws must be in kelvin, which is degrees Celsius plus two hundred and seventy-three. On the graph, the line, extended backwards, reaches zero volume at minus two hundred and seventy-three degrees Celsius, absolute zero. Here is the classic example. One litre of air at fifteen degrees Celsius, which is two hundred and eighty-eight kelvin, is heated at constant pressure. To double its volume to two litres you must double its absolute temperature to five hundred and seventy-six kelvin, which is three hundred and three degrees Celsius, not thirty. Heating gas makes it expand, and that expansion is what drives the piston down.
Part 5 · Gas laws
The combined gas law in the cylinder Boyle + Charles: P × V ÷ T = constant , so P₁V₁ ÷ T₁ = P₂V₂ ÷ T₂ Lets us follow pressure, volume and temperature together through the strokes Compression: volume down , temperature up , so pressure rises more than from volume alone Combustion near TDC: temperature soars at almost constant volume , so pressure soars Power stroke: volume up, temperature and pressure fall as the gas does work
P₁V₁ ÷ T₁ = P₂V₂ ÷ T₂ Before compression (BDC) P₁ = 1 bar, V₁ = 8 units, T₁ = 300 K After compression (TDC) V₂ = 1 unit (compression ratio 8 : 1) Heated by compression T₂ ≈ 690 K (about 415 °C) So the pressure is P₂ = 1 × 8 × 690 ÷ 300 ≈ 18.4 bar Boyle alone would give only 8 bar: compression heating raises the pressure much further (ignores heat loss to the walls; real figures are a little lower)
Chapter 1 · Engine Principles and Types
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Put Boyle and Charles together and you get the combined gas law: pressure times volume divided by absolute temperature is constant, so P one V one over T one equals P two V two over T two. This lets us follow all three properties through the strokes. Take a cylinder with a compression ratio of eight to one. At bottom dead centre the mixture is at one bar and three hundred kelvin. As the piston rises, the charge is squeezed into an eighth of its volume, and because it is compressed so quickly it heats up to around six hundred and ninety kelvin. Put those numbers into the combined law and the pressure at the top is about eighteen bar, not the eight bar Boyle alone would give. Then the spark fires, and the temperature soars while the volume hardly changes, so the pressure soars too. On the power stroke the gas expands, and its pressure and temperature fall.
Part 6 · Applied
Pressure, volume and temperature through the cycle Event Crank angle Volume Pressure Temperature Induction 0–180° (TDC → BDC) increases slightly below atmospheric low; fuel evaporation cools it Compression 180–360° (BDC → TDC) decreases rises rises (heated by compression) Combustion around TDC almost constant rises sharply rises sharply Power 360–540° (TDC → BDC) increases falls falls (after a brief rise) Exhaust 540–720° (BDC → TDC) decreases near atmospheric hot gas pushed out
Four strokes but five events ; one power stroke in 720° (two revolutions). The mass of the charge stays the same while the valves are shut.
Chapter 1 · Engine Principles and Types
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here are the gas changes in one table. On induction the piston goes down from top to bottom dead centre: the volume increases, the pressure is a little below atmospheric because the piston is drawing the charge in, and the temperature is low because evaporating fuel cools the mixture. On compression both valves are shut: the volume decreases while the pressure and temperature rise. The mass of the charge does not change, because nothing can get in or out. Combustion happens around top dead centre, where the volume is almost constant, so the pressure and temperature rise very sharply. On the power stroke the volume increases and the pressure and temperature fall as the gas gives up energy to the piston, after a short initial rise while burning finishes. On the exhaust stroke the burnt gas is pushed out. So there are four strokes but five events, and only one power stroke in seven hundred and twenty degrees.
Part 6 · Other engines
Diesel (compression ignition) engines Only air is drawn in and compressed, to a much higher compression ratio , until it is hot enough to ignite fuel Fuel is injected into the hot air: no spark, no carburettor Higher pressures need heavier reciprocating parts Akroyd Stuart and Rudolf Diesel patented early compression-ignition engines in the 1890s; aero-diesels flew in the 1930s Modern aero-diesels burn jet fuel and are certified as replacements in types such as the PA-28 and Cessna 172
Spark ignition Compression ignition mixture in, spark ignites CR about 7–9 : 1, AVGAS air only; fuel injected into hot air: CR 14–22 : 1 heavier parts, Jet A-1 / diesel
Chapter 1 · Engine Principles and Types
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
The compression ignition engine, usually called a diesel, has no spark plug. It draws in air alone and compresses it to a much higher compression ratio than a petrol engine, typically fourteen to twenty-two to one, so the air becomes hot enough to ignite fuel the moment it is injected. Because the pressures are higher, the pistons, rods and crankshaft are a little heavier. Credit for the idea is shared: Herbert Akroyd Stuart and Rudolf Diesel both patented compression-ignition engines in the early eighteen nineties, and the name diesel stuck. Aero-diesels flew in the nineteen thirties; the Junkers Jumo two-stroke diesels could give useful power at high altitude. Two-stroke designs need no conventional valves and give more power strokes per revolution. Today, with modern materials and turbocharging, aero-diesels that burn jet fuel are certified as replacement engines in aircraft such as the Piper PA-28 and the Cessna 172.
Part 6 · Other engines
The gas turbine in outline The same events, induction, compression, combustion, expansion, exhaust , but in separate components They all happen at once and continuously , not in turn Combustion at roughly constant pressure (piston engine: constant volume) The turbine drives the compressor ; what is left gives thrust or shaft power Thrust is a reaction to accelerating air backwards (Newton's third law)
Same events, done continuously compressor combustion turbine Piston engine Gas turbine Events in one cylinder, in turn in separate parts, all at once Combustion at constant volume at constant pressure Flow intermittent continuous Thrust from propeller jet reaction (and/or propeller)
Chapter 1 · Engine Principles and Types
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
The gas turbine does exactly the same jobs as the piston engine: it takes in air, compresses it, burns fuel in it, expands the hot gas to get work out, and exhausts it. The difference is that each event has its own component, and they all work at once, continuously. A compressor squeezes the air, combustion happens in a combustion chamber at roughly constant pressure, a turbine extracts energy to drive the compressor, and whatever energy is left accelerates the gas out of the back as a jet, or drives a propeller or a helicopter rotor. Look at the graph under the engine: the pressure peaks at the compressor exit, and the temperature peaks in the combustion chamber. The thrust of a jet is a reaction to throwing air backwards, Newton's third law again. We will study gas turbines in detail in the second half of the course.
Reference
Terms, units and formulae Quantity Units Formula Engine example Force N, lbf F = m × a; F = p × A gas pressure × piston area Work done J, ft·lbf W = F × d force × stroke Power W, hp (33 000 ft·lbf/min) P = work ÷ time brake horsepower at the propeller Pressure Pa (N/m²), psi, inHg p = F ÷ A manifold pressure in inches of mercury Density kg/m³ ρ = m ÷ V denser air → more power Kinetic / potential energy J ½ m V² ; m g h fast air in the venturi Efficiency % useful output ÷ total input thermal efficiency ≈ 25–28 %
Electrical terms (volts, amps, ohms, P = V × I) are covered in the Electrics course.
Chapter 1 · Engine Principles and Types
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a reference table of the quantities you will meet. Force is mass times acceleration, or in an engine pressure times area, in newtons or pounds force. Work is force times distance, in joules or foot-pounds. Power is work divided by time, in watts or horsepower, where one horsepower is thirty-three thousand foot-pounds per minute. Pressure is force divided by area, in pascals, pounds per square inch, or for manifold pressure, inches of mercury. Density is mass divided by volume; denser air means more mass in each cylinder and more power. Kinetic energy is a half m V squared, and potential energy is m g h. Efficiency is always useful output divided by total input, so it is always less than one hundred per cent. The electrical terms that also appear in reference tables, volts, amps and ohms, belong to the Electrics course.
Summary
What to take into the exam Engines Internal combustion: fuel burns in the cylinder. Heat → mechanical energy. Four strokes, five events, 720°.
Work and power W = F × d. Power = work ÷ time. 1 hp = 33 000 ft·lbf/min = 550 ft·lbf/s ≈ 746 W.
Energy Never created or destroyed. Thermal efficiency of a piston engine only ≈ 25–28 %.
Newton Inertia (valve lead and lag), F = m a and momentum, action and reaction (thrust).
Thermodynamics Heat and work interchange at a fixed rate; heat flows from hot to cold unaided.
Venturi Convergent: V ↑ p ↓ T ↓. Divergent: V ↓ p ↑ T ↑. Mass flow = ρ A V constant.
Gas laws PV = const; V/T = const; P₁V₁/T₁ = P₂V₂/T₂. Absolute pressure, kelvin.
Other engines Diesel: air only, high CR, injected fuel. Gas turbine: continuous, constant-pressure combustion.
Chapter 1 · Engine Principles and Types
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us pull the lesson together. An internal combustion engine burns its fuel inside the cylinder and converts heat into mechanical energy, with four strokes, five events and one power stroke in seven hundred and twenty degrees. Work is force times distance; power is work divided by time, and one horsepower is thirty-three thousand foot-pounds per minute, about seven hundred and forty-six watts. Energy is never created or destroyed, but only about a quarter of the fuel energy becomes useful work. Newton gives us inertia, which explains valve lead and lag, the momentum law, and action and reaction, which explains thrust. In a convergent duct velocity rises while pressure and temperature fall; a divergent duct does the opposite. The gas laws need absolute pressure and kelvin. And remember the two other families: the diesel ignites fuel in hot compressed air, and the gas turbine works continuously.