Engines · Chapter 3
Piston Engine Lubrication Why an engine needs oil, how wet- and dry-sump systems deliver it, the oil itself, and what the gauges are telling you.
OIL FILM SEPARATES THE SURFACES friction ↓ · wear ↓ · heat carried away
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter three is about lubrication. An engine is full of metal parts sliding and turning against each other under heavy load, at high speed and high temperature, and without oil it would wreck itself in minutes. In this lesson you will see what the oil does, which is a lot more than just reducing friction, how wet-sump and dry-sump systems store and circulate it, and what each part of the circuit is for: the tank, pumps, relief and check valves, filters and the cooler. Then we look at the oil itself, its viscosity and grades, and at what the oil gauges tell the pilot.
Roadmap
Keeping the engine alive 1 · Why oil Friction and wear, and the secondary jobs: cooling, cleaning, protecting, hydraulic and indicating.
2 · The systems Wet and dry sumps; tank, hot pot, filters, pumps, valves, cooler.
3 · The gauges Where temperature and pressure are sensed and what the readings mean.
4 · The oil Viscosity, grades, multigrades and types; hydraulicing, coring, checking.
Chapter 3 · Piston Engine Lubrication
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
This lesson has four parts. First, why an engine needs oil at all: friction and wear, and a list of secondary jobs that the oil also does, from cooling to telling the pilot how the engine is feeling. Second, the two kinds of system, wet sump and dry sump, and every part of a typical dry-sump circuit: the tank and its hot pot, the filters, the pressure and scavenge pumps, the relief and check valves, and the cooler. Third, the gauges: where oil temperature and pressure are measured, the typical values, and how to read abnormal indications. Finally, the oil itself, its viscosity and grades, multigrade and compound oils, and some practical points you must know as a pilot: hydraulicing, cold starts, coring, oil consumption and when to check the contents.
Part 1 · Why oil
Friction, wear and the lubricant Engine parts run under high loads, temperatures and speeds ; sliding metal resists movement: friction Friction grows with load, temperature and speed, and causes wear : loss of metal A lubricant keeps the surfaces apart with a film of lower friction: grease, powder or, in engines, oil Oil is either forced between parts (pressure lubrication) or flung onto them (splash ) More friction means more friction horsepower and so less brake horsepower
Dry: metal on metal Lubricated: an oil film between them sliding high friction, wear, heat: friction horsepower ↑, BHP ↓ oil film pressure lubrication (pumped) or splash lubrication (flung)
Chapter 3 · Piston Engine Lubrication
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The parts of an engine work under high loads, high temperatures and high speeds. When metal surfaces slide against each other there is a resistance to the movement, which is friction, and friction grows as the load, temperature and speed go up. The movement also wears the parts, which means metal is actually lost. Look at the magnified surfaces: even polished metal is rough, and the peaks catch on each other. Both friction and wear can be reduced by keeping the surfaces apart with a substance that has lower friction than the metals. That substance is a lubricant. Greases, powders and some solids can lubricate, but in engines we use oil. It can be forced between the moving parts under pressure, called pressure lubrication, or the parts can simply be splashed. Remember the link to performance: more friction means more friction horsepower, and therefore less brake horsepower at the propeller.
Part 1 · Why oil
The jobs the oil does Primary: reduce friction and wear The main task : keep moving surfaces apart.
Cooling The most important secondary job: carries heat away from bearings, pistons and cylinder walls.
Cleaning Carries away combustion by-products and debris to the filters.
Protection Coats internal parts against corrosion .
Hydraulic medium Cushions shock loads between crankshaft and bearings; powers a variable-pitch propeller .
Indicating medium Its pressure and temperature give early warning of mechanical failure or power loss.
Chapter 3 · Piston Engine Lubrication
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil has one primary job and several secondary ones, and exam questions like to separate them. The primary task of the lubrication system is to reduce friction and to reduce component wear. The secondary functions are next. Cooling is the most important of them: oil flowing through the engine carries heat away from the bearings, the pistons and the cylinder walls. Cleaning: the oil picks up the by-products of combustion and small particles and carries them to the filters. Protection: a film of oil protects internal metal parts from corrosion. Hydraulic medium: the oil film cushions the shock loads between the crankshaft and its bearings, reducing vibration, and oil pressure can operate a hydraulic variable-pitch propeller. And indicating medium: oil pressure and temperature tell the pilot about the condition of the engine and can give early warning of failure. So if you are asked for the primary task, the answer is to reduce friction and wear.
Part 2 · The systems
Wet sump and dry sump The principle of lubrication is the same; the difference is where the oil is stored Wet sump : all the oil is in the engine and its sump ; most light, non-aerobatic aircraftDry sump : oil kept in a separate, remote tank ; scavenge pumps keep the sump almost emptyChoice depends on the engine's power output and the aircraft's role Both use a pressure pump to force oil round the engine
Wet sump Dry sump engine sump engine sump all the oil in the sump simple, light: most non-aerobatic light aircraft tank oil kept in a separate tank; scavenge pump empties sump higher power, aerobatic
Chapter 3 · Piston Engine Lubrication
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two kinds of lubrication system in common use, wet sump and dry sump. The way the oil lubricates the engine is the same in both; the difference is where the supply of oil is stored. In a wet-sump engine, all the oil is kept in the engine itself, in the sump at the bottom of the crankcase, as you can see under the crankshaft of this in-line engine. That makes the construction simple and light, and most light, non-aerobatic aircraft use it. In a dry-sump engine the oil is stored in a separate tank mounted away from the engine. A pressure pump still sends the oil round the engine, but scavenge pumps then pump it out of the sump and back to the tank, so the sump stays almost dry. Which system an engine uses depends mainly on its power output and the role of the aircraft: high-powered and aerobatic engines tend to be dry sump.
Part 2 · The systems
The drawbacks of a wet sump Manoeuvres Oil is flung round by the shafts; risk of over-oiling ; inverted flight is particularly hazardous.
Temperature Harder to control: the oil is stored inside the hot engine casing .
Contamination Constant contact with the hot engine: the oil is contaminated and oxidises more easily.
Capacity The supply is limited by the size of the sump .
Dry sump answer A remote tank solves all four, at the cost of extra pumps and pipes.
Diesel engines Typically wet sump , and always with an oil cooler : they make more heat.
Checking Wet sump: check after the oil has drained back (15–20 min ). Dry sump: straight after shut-down.
Exam phrase "In a wet-sump system the oil is contained in the engine and sump ."
Chapter 3 · Piston Engine Lubrication
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The wet sump is simple, but it has four drawbacks. First, manoeuvres. The oil sits in the crankcase, where the revolving shafts fling it around, so the engine can be over-oiled, and inverted flight is particularly hazardous because the oil is no longer where the pump pick-up is. Second, temperature control is harder, because the oil is stored inside the hot engine casing. Third, that constant contact with the hot engine means the oil is contaminated and oxidises more easily. Fourth, the amount of oil is limited by the size of the sump. Storing the oil in a remote tank, the dry-sump system, overcomes all four, at the cost of more pumps and pipes. Diesel aero engines are typically wet sump, and they always have an oil cooler because they generate more heat. And remember that the two systems are checked at different times after shut-down, which we will come back to at the end.
Part 2 · The systems
A typical dry-sump system
tank suction filter pressure pump pressure filter engine bearings sump scavenge pump oil cooler relief valve check valve gravity feed → pressure (red) → scavenge return (blue)
Gravity feed (amber) → pressure (red) → engine → sump → scavenge return (blue) through the cooler to the tank.
Chapter 3 · Piston Engine Lubrication
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is a complete dry-sump circuit. Oil leaves the tank, mounted above the engine, and flows by gravity through a coarse suction filter to the pressure pump. The gear-type pressure pump forces it, now under pressure and drawn in red, through a fine pressure filter and into the engine, where drillings carry it to the bearings, gears and cylinder walls. A relief valve across the pump returns any excess oil to the pump inlet. After doing its work, the oil drains down into the sump. From there the scavenge pump, which is larger than the pressure pump, picks it up and sends it back, drawn in blue, through the oil cooler to the tank. The principal units are therefore the tank, filters, pressure and scavenge pumps, the cooler, and the pressure and temperature gauges. We will now look at each one in turn.
Part 2 · Components
The oil tank Sheet metal, baffled and strengthened against surging in manoeuvres Mounted above the engine where possible: gravity feed to the pressure pump Air space above the oil allows for: extra return on start-up , expansion as the oil heats, frothing , and oil displaced from the propeller and controlsVented through the crankcase breather , so frothing does not blow oil overboard The breather also stops pressure building up in the crankcase
air space baffles stop surging oil level gravity feed to the pump vent • extra return at start-up • expansion as oil heats • frothing (aeration) • oil displaced from the propeller and controls
Chapter 3 · Piston Engine Lubrication
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil tank is made of sheet metal, with internal baffles that strengthen it and stop the oil surging about during manoeuvres. Wherever possible it is mounted higher than the engine, to give a gravity feed to the pressure pump. It holds enough oil for the engine, plus an air space above the oil, and the reasons for that air space are a favourite question. First, when the engine is started, the oil that drained into the sump after the last flight is scavenged back, so there is a surge of extra return. Second, the oil expands as it absorbs heat from the bearings. Third, the return oil froths, because it is full of air. Fourth, oil displaced from the variable-pitch propeller and other automatic devices comes back to the tank. The tank is vented through the crankcase breather, which also prevents pressure building up inside the crankcase.
Part 2 · Components
The hot pot, feathering reserve and de-aerator Hot pot : a small compartment over the outlet; only oil inside it reaches the pumpCold, thick oil barely passes its small ports , so only a little oil circulates and it warms quickly As the oil thins, the ports pass more and more oil into circulation With feathering propellers, the ports sit above the tank bottom : a feathering reserve if the main supply is lost Return oil runs over a de-aerator plate that separates the air: less frothing
to pressure pump de-aerator plate separates the air small ports cold oil barely passes hot pot hot oil recirculates feathering reserve below the main outlet main outlet
Chapter 3 · Piston Engine Lubrication
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Large oil tanks often contain a hot pot, a separate compartment, a metal cylinder standing over the outlet to the pump. Only oil inside the hot pot can reach the pump. When the engine starts from cold, the level in the hot pot drops and uncovers a ring of small ports. Those ports offer great resistance to thick cold oil, so very little of the tank's oil gets in. The engine's returning oil goes straight back into the hot pot and is recirculated, so this small quantity warms up quickly. The hot return also warms the hot pot walls, the nearby oil thins, and progressively more oil is drawn into circulation. When feathering propellers are fitted, the lowest ports are set above the tank bottom, which leaves a reserve of oil for feathering even if the main feed fails. Finally, returning oil runs over a de-aerator plate, which separates out the air and reduces frothing.
Part 2 · Components
Suction filter and pressure pump Suction filter : coarse wire mesh between tank and pump; stops large particles damaging the pumpPressure pump : two deep-toothed spur gears in a close-fitting casing, driven from the accessory housingOil is carried round the outside, between the teeth , from inlet to outlet The engine's passages resist the flow, so pressure builds Pressure depends on pump speed, oil temperature and the resistance of the components
inlet outlet oil carried round the outside in the spaces between the teeth Pressure depends on: pump speed · oil temperature · resistance of the engine Coarse suction filter upstream protects the pump
Chapter 3 · Piston Engine Lubrication
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Between the tank and the pressure pump there is a suction filter, a coarse wire mesh that removes large solid particles before they can damage the pump. The pressure pump itself is usually a spur gear pump: two deep-toothed gears turning in a close-fitting casing, driven through the accessory housing. Watch the gears. Oil is not squeezed between them in the middle; it is carried round the outside of each gear, in the spaces between the teeth, from the inlet side to the outlet side. The outlet is enclosed, and the narrow passages of the engine resist the flow, so pressure builds up. As the pump turns faster the gauge rises, and when it reaches the setting the relief valve opens and returns oil to the inlet. So the pressure you see depends on three things: the speed of the pump, the temperature of the oil, and the resistance offered by the components being lubricated.
Part 2 · Components
The pressure relief valve The pump is sized to give enough pressure at low speed with hot oil , its worst case At normal speeds it would therefore give a dangerously high pressure The relief valve , across the pump inlet and outlet, opens at a set pressure and returns oil to the inlet So above idle the pressure is relatively unaffected by engine speed A relief valve sticking on and off its seat causes small pressure fluctuations
0 700 1400 2100 2800 0 30 60 90 120 engine RPM oil pressure (psi) without a relief valve cold, thick oil hot, thin oil relief valve setting normal range Pump sized for low RPM and hot oil, so it would over-deliver; the relief valve returns the excess to the pump inlet Above idle, pressure is nearly independent of RPM
Chapter 3 · Piston Engine Lubrication
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The capacity of the pressure pump has to be big enough to supply the minimum safe oil pressure under its most adverse conditions, which are low turning speed and hot, thin oil. That means that in normal running, at higher speed or with thicker oil, it would deliver far too much and the pressure would become dangerously high, as the dashed line shows. To prevent that, a pressure relief valve is fitted across the inlet and outlet of the pump. When the pressure reaches a predetermined figure, the valve opens and returns enough oil to the inlet side to limit the maximum pressure. The engine therefore has a range of operating pressure from idle to maximum RPM, but once the valve is controlling, the pressure is relatively unaffected by engine speed. Notice too that cold oil reaches the relief setting at a lower RPM. A relief valve that sticks, opening and closing unevenly, is the classic cause of small fluctuations in oil pressure.
Part 2 · Components
Check valve and pressure filter Check (non-return) valve : stops hot, thin oil draining by gravity from the tank through the pump into the crankcase after shut-downWithout it the engine floods: over-oiling (and risk of hydraulicing ) A lightly sprung valve or an electrically operated shut-off valve ; opens when the engine starts Pressure filter : downstream of the pressure pump; removes very small particles before the bearingsSpring-loaded bypass opens if the oil is cold or the element blocked; also protects if the pump breaks up
Check valve Pressure filter from tank (gravity) to pressure pump engine stopped: holds the hot thin oil in the tank no "over-oiling" of the crankcase bypass relief valve fine element after the pump bypass opens if the oil is cold or the element blocks unfiltered oil is better than no oil
Chapter 3 · Piston Engine Lubrication
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the tank is usually above the pump, there is a problem when the engine is stopped. Hot, thin oil, pushed by gravity, can seep through the clearances of the pressure pump and drain the tank into the crankcase, flooding the engine. That is called over-oiling. To prevent it, a check valve, also called a non-return or one-way valve, is fitted. It is either a lightly sprung valve, which the pump pressure easily opens once the engine is running, or an electrically operated shut-off valve, and it holds the oil back until the engine is started. Downstream of the pressure pump, before the oil enters the engine, is the pressure filter. It is much finer than the suction filter and removes very small particles before they reach the bearing surfaces. A spring-loaded relief valve bypasses the element when the oil is cold and thick or the element is blocked, because unfiltered oil is better than none, and it also protects the engine if the pump breaks up.
Part 2 · Components
The scavenge pump Returns oil from the sump to the tank , keeping the sump dry After shut-down, oil drains into the sump; on start-up there is extra oil to remove Return oil is also aerated and has more volume So the scavenge pump has a larger capacity : 25–50 % more than the pressure pump Returning oil passes a scavenge filter on its way back to the tank
Pressure pump capacity 100 % Scavenge pump 125–150 % Same drive, bigger gears in the scavenge pump Why bigger? On start-up the sump already holds oil that drained down; frothy return oil also has more volume. An equal-sized pump could never empty the sump. Return oil passes a scavenge filter on its way to the tank
Chapter 3 · Piston Engine Lubrication
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
The scavenge pump returns the oil from the sump to the tank. Think about what happens when the engine is stopped: the oil clinging to the crankcase walls drains down into the sump and stays there. When the engine is started again, that extra oil has to be removed, and the oil coming back is also frothy, full of air, so it has a larger volume than the oil that went in. If the scavenge pump were the same size as the pressure pump, it could never catch up, and the sump would flood. So, to keep the sump dry, the scavenge pump has a larger capacity than the pressure pump, in practice twenty-five to fifty per cent larger. Watch the sump as the bigger pump empties it. On its way back to the tank, the returning oil is cleaned by a scavenge filter, which also catches metal particles that can warn of wear.
Part 2 · Components
The oil cooler Oil that gets too hot fails as a lubricant; the cooler limits its temperature A matrix of tubes spreads the oil in thin films across the cooling air Anti-surge valve : bypasses the matrix when the oil is cold , to avoid damage from very high pressureOil temperature depends on power (heat made), cooling-air temperature and airflow through the cooler Shutters : closed for a quick warm-up and at altitude; in a climb (high power, low speed) watch the temperature
matrix of tubes (hexagonal ends) cooling air anti-surge cold bypass shutters shut cold Oil temperature depends on: power (heat made), cooling-air temperature and cooling-air flow Climb: high power, low speed → watch oil temperature
Chapter 3 · Piston Engine Lubrication
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil cools the inside of the engine, but if the oil itself gets too hot it can no longer lubricate, so a cooler is fitted in the system. It is a matrix of tubes that spreads the oil in thin films while cooling air flows across. When the engine is started from cold, the matrix is full of thick oil, and forcing it through those small passages would need a very high pressure that could damage the cooler. So an anti-surge valve bypasses the matrix while the oil is cold; watch it close as the oil warms, sending the flow through the matrix. The oil temperature depends on three things: the heat made by the engine, which depends on power, the temperature of the cooling air, and the rate of airflow through the cooler. That is why a climb, with high power and low speed, needs watching. Shutters are closed for a quick warm-up and at altitude.
Part 3 · The gauges
Oil temperature and pressure indications Temperature is sensed at the inlet to the pressure pump (oil leaving the tank); about 85 °C is normalPressure is sensed at the outlet of the pressure pump ; 50–100 psi typicalSensors: electrical, or direct-reading mechanical (pressure) Oil temperature and pressure must be shown on the flight deck; quantity may be, or is checked by dipstick or sight glass They are perhaps the pilot's most important indications of engine condition
0 30 60 90 120 OIL TEMP °C 0 30 60 90 120 OIL PRESS psi sensed at the INLET to the pressure pump (oil leaving the tank) sensed at the OUTLET of the pressure pump Typical: about 85 °C and 50–100 psi Temperature and pressure: mandatory on the flight deck Quantity: may be shown, or checked by dipstick or sight glass
Chapter 3 · Piston Engine Lubrication
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
The oil system tells the pilot a great deal, but only if you know where each value comes from. On a piston engine the oil temperature is measured at the inlet to the engine-driven pressure pump, in other words the oil leaving the tank in a dry-sump system, usually by an electrical sensor; around eighty-five degrees Celsius is considered normal. The oil pressure is sensed at the outlet side of the pressure pump, where the pressure is created; typical values are fifty to one hundred pounds per square inch, depending on the engine. A common exam distractor puts the pressure sensing on the inlet side, which would read almost nothing. Oil temperature and pressure must be displayed on the flight deck. Oil quantity may also be displayed; if not, there will be a dipstick or a sight glass to check it before flight. Correct oil pressure and temperature are perhaps the most important indications you have of the condition of the engine.
Part 3 · The gauges
Reading the oil gauges Indication Likely meaning Action Pressure within ~30 s of start (e.g. Piper Warrior) Normal: oil is reaching the bearings If no pressure in the stated time, shut down High pressure after a cold startNormal : thick oilDo not accelerate until it falls into the normal range as the oil warms High temperature with low pressure Hot, thin oil Pressure and temperature go together; reduce power, increase cooling Low pressure at normal temperature Imminent engine failure (pump, leak, bearings)Land as soon as possible Small fluctuations in pressureRelief valve sticking; or low oil level Monitor; check quantity Excessive oil consumption, blue smoke Wear: rings, valve guides Engineering inspection
Oil pressure should be in its operating range at the correct operating temperature; the two readings depend on each other.
Chapter 3 · Piston Engine Lubrication
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is how to read the gauges. After start, positive oil pressure must appear within a specified time, for example thirty seconds on a Piper Warrior; if it does not, shut down. If you start from cold, the pressure may be very high. That is normal, provided it falls into its normal range as the oil warms, and you should not accelerate the engine until it does. Pressure and temperature depend on each other: hot oil is thin, so a high temperature can bring a low pressure. Low pressure at a normal temperature is serious; it suggests imminent engine failure, and you should land as soon as possible. Small fluctuations in pressure are typically caused by the relief valve sticking, or by a low oil level. And high oil consumption, perhaps with blue smoke, points to wear that needs an engineer.
Part 4 · The oil
Viscosity Viscosity (grade): a fluid's internal friction , its resistance to flow Free-flowing oil: low viscosity (thin); sluggish oil: high viscosity (thick) Higher temperature → lower viscosity , and vice versa The oil must stay within limits from a cold start to long high-power running; that range is its viscosity index Measured by timing a fixed quantity of oil through an orifice at a set temperature
0 20 40 60 80 100 120 10 100 1000 10000 oil temperature (°C) viscosity (cSt, log scale) Grade 80 (SAE 40) Grade 100 (SAE 50) SAE 15W-50 multigrade normal running Hotter → thinner. A multigrade stays thinner when cold but is as thick as a grade 100 when hot (higher viscosity index)
Chapter 3 · Piston Engine Lubrication
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
How thick an oil is matters a great deal, and that property is its viscosity, or grade. Viscosity is defined as the internal friction of a fluid, its resistance to flow. A liquid that flows freely, a thin oil, has a low viscosity; one that is sluggish, a thick oil, has a high viscosity. Viscosity changes with temperature: as an oil gets hotter, its viscosity falls, and as it cools, it rises. Look at the graph; the scale is logarithmic, so each line up is ten times thicker. A straight grade one hundred oil is thousands of times thicker at minus ten than at its running temperature. An engine runs from a cold start to long periods at high power, and the oil has to stay within usable limits across that range; how well it does so is described by its viscosity index. The multigrade line is flatter: thin enough to flow when cold, and thick enough when hot.
Part 4 · The oil
Viscosity grades: two numbering systems Both systems time a fixed quantity of oil through an orifice; the lower the number, the thinner the oil . The aviation grade is twice the SAE number.
Commercial SAE number Aviation (Saybolt-based) grade Typical use 30 60 thin: lightly loaded engines, cold weather 40 80 e.g. UK light aircraft in winter 50 100 e.g. the same aircraft in summer 60 120 thick: highly loaded, high-power engines 15W-50 (multigrade) — thin like a 15 when cold, thick like a 50 when hot
Too thick an oil at too low a temperature makes starting difficult. The choice depends on engine loading and average ambient temperature.
Chapter 3 · Piston Engine Lubrication
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two numbering systems are used for aviation oil viscosity. The commercial one is the Society of Automotive Engineers, or S A E, system. The aviation grades are based on the Saybolt Universal system. Both work by timing how long a fixed quantity of oil at a given temperature takes to flow through an orifice, and in both the lower the number, the thinner the oil. The aviation grade number is simply twice the S A E number, so S A E thirty is grade sixty, forty is eighty, fifty is one hundred and sixty is one hundred and twenty. Lightly loaded engines use a low viscosity, thin oil, and highly loaded, high-powered engines need a thick one. Climate matters too: a light aircraft in a British winter might use grade eighty, and in summer grade one hundred. Too thick an oil in the cold makes starting hard, which is why multigrade oils, such as fifteen W fifty, behave like a thin oil when cold and a thick one when hot.
Part 4 · The oil
Types of aviation piston-engine oil Mineral base Aircraft piston engines normally use mineral-based oils.
Straight oil No additives . Marked with the grade only, e.g. 80 . Used for running in new engines or specific installations.
Compound oil With additives: anti-oxidants, detergents, oiliness agents . Marked e.g. AD 80 or W 80 .
AD = ashless dispersant Cleaning qualities: holds dirt in suspension to the filters, leaving no ash deposits.
Semi-synthetic Trialled and approved by some engine makers.
Multigrade Two viscosity numbers, e.g. SAE 15W-50 : thin when cold, thick when hot.
Never mix blindly Use only the oils the engine manufacturer approves.
Consumption Some oil always burns past rings and valves: about 1 pint per hour in a light aircraft.
Chapter 3 · Piston Engine Lubrication
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aircraft piston engines normally use mineral-based oils. An oil with no additives is called a straight oil, and its container shows only the viscosity number, for example eighty. Straight oil is generally used only when running in a new engine, so that the rings can bed in, or for particular installations. Additives can be added to meet the needs of engine operation: anti-oxidants, detergents and oiliness agents. Those are compound oils, and their containers carry letters as well as the number, for example A D eighty or W eighty, depending on the manufacturer. A D stands for ashless dispersant, an oil with special cleaning qualities: it holds dirt in suspension until the filters catch it, without leaving ash deposits. Some engine makers have also approved semi-synthetic oils, and multigrade oils carry two viscosity numbers. Always use what the engine manufacturer approves.
Part 4 · Operation
Hydraulicing in radial and inverted engines In radial and inverted engines oil can drain past the rings into the lower cylinders It collects between the piston and the cylinder head Oil is incompressible : on the compression stroke it can cause a hydraulic lock and serious damage Before start, pull the engine through by the propeller to prove there is no lock Make sure the magnetos are OFF before turning the propeller
oil in lower cylinders hydraulic lock Pull the propeller through by hand (magnetos OFF) before start Radial and inverted engines
Chapter 3 · Piston Engine Lubrication
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
On radial and inverted engines, the pilot needs to understand the lubrication system even before starting. Some of the cylinders point downwards, and while the engine is stopped, oil can drain past the piston rings and collect in the lower cylinders, between the piston and the cylinder head. Oil is incompressible. If that cylinder comes up on its compression stroke full of oil, the piston cannot complete its travel, and the result is a hydraulic lock that can bend a connecting rod or crack a cylinder. This is called hydraulicing. The answer is to pull the engine through by hand, turning the propeller through several revolutions before starting, to make sure no cylinder is locked. And because turning a propeller by hand can start an engine, always confirm that the magnetos are switched off first.
Part 4 · Operation
Coring on a very cold start In very cold weather, viscous oil does not flow properly through the engine and cooler Less flow means less heat carried away: the oil temperature rises rapidly But only locally , at the sensor: most of the oil is still cold Cure: close the oil cooler flaps Temperature rises at first, the cooler core warms and flows, then temperatures come back down
cold, congealed core no flow, no cooling hot oil finds a path round the outside Very cold start: thick oil will not flow properly Oil temperature gauge rises fast, but only locally Most of the oil is still cold Cure: close the oil cooler flaps; the core warms and flows, then temperatures come back down
Chapter 3 · Piston Engine Lubrication
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Coring is a problem of starting in very cold weather. The cold oil is so viscous that it does not flow properly through the engine, and especially through the narrow passages of the cooler, where a cold core of oil can congeal while hot oil finds a way round the outside. Remember that one of the oil's main jobs is cooling. With the flow reduced, the heat being generated in the engine is not carried away, so the oil temperature gauge rises rapidly. But the rise is only local, at the point of sensing. Most of the oil in the system is still cold. The cure may seem backwards: close the oil cooler flaps. That initially pushes the temperature up further, but it warms the cooler, the congealed core thins and starts to flow, and once the whole system is circulating, the temperatures come back down to normal.
Part 4 · Operation
Oil consumption and checking the contents Some oil always reaches the combustion gases and burns: a light aircraft uses about 1 pint per hour ; more suggests wear Always check the contents before flight Dry sump : check immediately after shut-down (within a few minutes), before oil migrates from the tank to the sumpLarge engines fit a check valve under the tank, closed by a spring or electrically at shut-down, to stop that migration Wet sump : wait at least 15–20 minutes for the oil to drain back into the sump, as in a car
0 5 10 15 20 25 30 minutes after shut-down oil in a dry-sump TANK oil back in a wet SUMP check check (≥ 15–20 min) Dry sump: check immediately after shut-down, before oil drains from the tank into the engine Wet sump: wait 15–20 minutes for the oil to drain back into the sump, as in a car Normal consumption, light aircraft: about 1 pint per hour
Chapter 3 · Piston Engine Lubrication
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because oil lubricates the cylinder walls and valve stems, some of it meets the combustion gases, and the seals there are never perfect, so some oil is always burned. Ignoring external leaks, a light aircraft engine uses around one pint an hour; more than that suggests wear in the engine. Always check the oil contents before flight, and know when to check. In a dry-sump system, check immediately after the engine has stopped, realistically within a few minutes, before the oil migrates under gravity from the tank down into the engine sump and makes the tank read low. Large engines fit a check valve under the tank, closed by a spring or an electric actuator at shut-down, to stop that migration. A wet-sump engine is the opposite. The oil has to drain back into the sump from the walls of the engine, so wait at least fifteen to twenty minutes, just as you would with a car.
Summary
What to take into the exam Functions Primary: reduce friction and wear. Secondary: cool, clean, protect, hydraulic medium, indicating medium.
Wet vs dry Wet: oil in engine and sump. Dry: remote tank, scavenge pump. Wet drawbacks: manoeuvres, heat, contamination, capacity.
Tank Above the engine (gravity), baffled; air space for start-up return, expansion, frothing, prop oil. Hot pot, de-aerator.
Pumps and valves Gear pump; relief valve returns to inlet (pressure ~independent of RPM); check valve stops over-oiling; scavenge pump 25–50 % larger.
Filters and cooler Coarse suction, fine pressure (bypass), scavenge filter on return. Cooler anti-surge valve bypasses when cold.
Gauges Temperature at pump inlet (~85 °C); pressure at pump outlet (50–100 psi). Cold start high pressure normal.
Viscosity Resistance to flow; falls as temperature rises. Aviation grade = 2 × SAE. Multigrade 15W-50.
Operation Hydraulicing: pull through, mags off. Coring: close cooler flaps. Check dry sump at once, wet sump after 15–20 min.
Chapter 3 · Piston Engine Lubrication
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. The primary task of the oil is to reduce friction and wear; its secondary jobs are cooling, cleaning, protection against corrosion, acting as a hydraulic medium and as an indicating medium. A wet sump keeps the oil in the engine and sump; a dry sump keeps it in a remote tank and uses a larger scavenge pump. The tank sits above the engine and has an air space for start-up return, expansion, frothing and propeller oil. The gear pressure pump is protected by a relief valve that returns oil to the inlet, so pressure is nearly independent of RPM; a check valve stops over-oiling. Filters are coarse on suction, fine on pressure with a bypass, and a scavenge filter cleans the return. Temperature is sensed at the pump inlet and pressure at its outlet. Viscosity falls with temperature; the aviation grade is twice the S A E number. And remember hydraulicing, coring and when to check the oil.