Engines · Chapter 7
Mixture Air and fuel by mass: the chemically correct 15 to 1, rich and weak mixtures, what each phase of flight needs, leaning with the EGT gauge, and why diesels run lean.
8:1
10:1
12.5:1
15:1
18:1
20:1
RICH
WEAK
chemically correct
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter seven is about mixture: how much fuel goes with how much air. Get it right and the engine gives its full power, runs smoothly and stays cool. Get it wrong and you waste fuel, foul the plugs, overheat the cylinders or even risk detonation. We will start with the chemistry of the chemically correct ratio, then see why engines actually run a little rich for power and a little weak for economy, what each phase of flight needs, how altitude changes the mixture, how to lean with the exhaust gas temperature gauge, and finally why an aero-diesel has no mixture lever at all.
Chapter 7 · Roadmap
Mixture: the right amount of fuel for the air 1 · The ratio 15:1 by mass is chemically correct; rich and weak; the burnable range; richness.
2 · Power and economy Best power about 12.5:1, best economy weaker; what weak and rich mixtures do to the engine.
3 · Phases of flight Rich to start and idle, 10:1 take-off, 11:1 climb, leaned cruise; altitude richens a carburettor.
4 · Smoke and flame Black smoke and sooty plugs mean rich; overheating and popping back mean weak.
5 · Leaning with EGT The thermocouple, the peak at 15:1, rich of peak and lean of peak, CHT.
6 · Aero-diesels Unthrottled air, lean running, no mixture lever, single-lever FADEC.
Chapter 7 · Mixture
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the plan for this chapter. First, the ratio itself: the chemically correct mixture of fifteen to one by mass, what rich and weak mean, and the range in which a mixture will burn at all. Second, power and economy: why the best power comes at about twelve and a half to one, the best economy a good deal weaker, and what weak and rich mixtures do to the engine. Third, each phase of flight, from starting to take-off, climb and cruise, and why the mixture richens as you climb with a carburettor. Fourth, how to recognise a rich or weak mixture. Fifth, leaning with the exhaust gas temperature gauge. And finally, the aero-diesel, which needs no mixture lever at all.
Part 1 · The ratio
Mixture is measured by mass Mixture : the ratio of air to fuel entering the cylindersAlways quoted by mass (weight) : e.g. 15 kg of air to 1 kg of fuel Not by volume: 15 kg of air fills about 12 m³ , 1 kg of AVGAS only about 1.4 litres Written as air : fuel (15:1) or as fuel : air (1/15 ≈ 0.067) A bigger air number means less fuel : 18:1 is weaker than 12:1
15 kg air
1 kg fuel
Air/fuel ratio is by MASS (weight)
≈ 12 m³
of air at sea level
(15 kg ÷ 1.225 kg/m³)
≈ 1.4 litres
of AVGAS
(1 kg ÷ 0.72 kg/l)
Chapter 7 · Mixture
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
Mixture means the proportion of air to fuel in the charge that enters the cylinders, and it is always measured by mass, which in exam language is the same as weight. So the chemically correct figure is fifteen kilograms of air to one kilogram of fuel, not fifteen litres or fifteen cubic centimetres. Why mass? Because combustion is chemistry: so many molecules of oxygen join so many molecules of carbon and hydrogen, and the mass tells you how many molecules you have. Volume would be useless, because air changes volume with every change of pressure and temperature. Look at the scale of the difference: fifteen kilograms of sea level air fills about twelve cubic metres, while one kilogram of avgas is only about one point four litres. The ratio can be written as air to fuel, fifteen to one, or as fuel to air, one fifteenth. And remember: the bigger the air number, the less fuel, so eighteen to one is weaker than twelve to one.
Part 1 · The ratio
The chemically correct ratio: 15 to 1 At 15:1 by mass all the oxygen combines with all the carbon and hydrogen : complete combustion Also called the stoichiometric mixture; products CO₂ and H₂O, nitrogen passes through A mixture will burn only between about 8:1 (rich limit) and 20:1 (weak limit) It gives the hottest combustion: risk of detonation at high power So 15:1 is the reference, but not the setting normally used
Complete burning: all O₂ meets all C and H
Fuel
C and H
+
Air
≈ 23% O₂ by mass
CO₂
H₂O
N₂ (unchanged)
Octane, C₈H₁₈: 12.5 O₂ per molecule
→ about 15 kg of air per kg of fuel
6
8
10
12
15
18
20
22
8:1 rich limit
20:1 weak limit
15:1 chemically correct
air : fuel by mass · burns only inside the orange band
Chapter 7 · Mixture
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel is a hydrocarbon, made of carbon and hydrogen. When it burns, oxygen from the air joins the carbon to make carbon dioxide and joins the hydrogen to make water. If there is exactly enough oxygen for all of the fuel, every molecule pairs up and combustion is complete; for aviation gasoline that happens at about fifteen to one by mass. This is the chemically correct, or stoichiometric, ratio. In the scene, the charge comes in through the inlet valve as blue mixture, the spark lights it, it burns orange as it drives the piston down on each power stroke, and it leaves through the exhaust as grey gas. A mixture will only burn at all between about eight to one, the rich limit, and twenty to one, the weak limit. And here is the twist: fifteen to one burns hottest of all, so at high power it invites detonation. It is the reference point, not the setting we normally use.
Part 1 · The ratio
Rich, weak and richness
RICH: extra fuel, oxygen all used
WEAK: spare oxygen
15:1 chemically correct (richness 1.0)
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
9:1 exam: "rich"
10:1 take-off
11:1 climb
12.5:1 best power
16.6:1 best economy
18:1 weak economy cruise
Richness = (fuel/air actual) ÷ (1/15). 12.5:1 → 1.2 (rich) · 18:1 → 0.83 (weak, fuel 1/18 of the air)
Rich : more fuel than chemically correct (smaller air number). Weak (lean): less fuel, so oxygen is left over.
Chapter 7 · Mixture
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is the whole scale. Anything with more fuel than fifteen to one is rich, and that means a smaller air number: twelve and a half, eleven, ten, or the nine to one that an exam calls rich. In a rich mixture all the oxygen is used up and some fuel is left over. Anything with less fuel is weak, or lean, which means a bigger air number such as eighteen to one, and then some oxygen is left over. Some exams describe a mixture by its richness. Richness is the actual fuel to air ratio divided by the chemically correct one, a fifteenth. So the correct mixture has a richness of one, twelve and a half to one has a richness of one point two, and a weak mixture of eighteen to one has a richness of about nought point eight three; with one unit of air it carries one eighteenth of a unit of fuel. Notice the landmarks for take-off, climb, best power and best economy.
Part 2 · Power and economy
Why engines run slightly rich for power Mixing and distribution are never perfect : some cylinders get richer charge, some weaker A slightly rich cylinder loses little power: all the oxygen is still used, and the spare fuel cools A weak cylinder loses power quickly : some of its oxygen does no work So for maximum power the setting is about 12.5:1 , richer than chemically correct Then no cylinder is left running badly weak
Carburettor set to 15:1
13.5:1
rich
14.5:1
rich
16.5:1
WEAK
15:1
correct
one cylinder weak: power lost, runs hot
Carburettor set to 12.5:1
11.5:1
rich
12.5:1
rich
13.5:1
rich
12.8:1
rich
every cylinder slightly rich: full power, cooler
Chapter 7 · Mixture
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
In theory fifteen to one should give the hottest flame and the most power. In practice the fuel and air are never perfectly mixed, and the manifold never shares them out exactly evenly, so some cylinders receive a richer charge and others a weaker one. Now compare the two errors. A cylinder that is slightly rich hardly loses any power: all of its oxygen is still burnt, and the extra fuel simply evaporates and cools the charge, which is actually helpful. A cylinder that is weak loses power much faster, because some of the oxygen it took in does no work at all. So when maximum power matters more than economy, the carburettor is set richer than chemically correct, at about twelve and a half to one. In the drawing you can see why: set to fifteen to one, one cylinder ends up weak; set to twelve and a half, every cylinder is slightly rich and none is weak.
Part 2 · Power and economy
Power and fuel consumption against mixture
8
10
12
14
16
18
20
50
60
70
80
90
100
Air : fuel ratio (rich ← → weak)
Power, % of best
best power 12.5:1
15:1
falls fast
falls slowly
8
10
12
14
16
18
20
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
Air : fuel ratio (rich ← → weak)
SFC (relative to best power = 1.0)
best economy ≈ 16.6:1
12.5:1
15:1
Same throttle and RPM throughout. SFC = fuel burnt per unit of power per hour: the lower, the more economical.
Chapter 7 · Mixture
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
These two graphs are the heart of the chapter. On the left is power, at a fixed throttle and RPM, as the mixture changes. Power peaks at about twelve and a half to one. Go richer and it falls only slowly. Go weaker and it falls steeply, which is why weakening the mixture below the best power ratio always costs power. On the right is specific fuel consumption, which is the fuel burnt per unit of power per hour; the lower it is, the more economical the engine. As you weaken from twelve and a half to one, the fuel flow falls faster than the power, so specific fuel consumption keeps falling until its lowest point, the best economy mixture, at about sixteen and a half to one in this example. Enriching the mixture always increases specific fuel consumption. So rich gives power and cooling, weak gives economy and endurance, and the chemically correct point sits between them.
Part 2 · Power and economy
Weak mixtures burn slowly: advance the spark Extra air means more nitrogen in the charge: the flame spreads more slowly and burns cooler Power falls, but fuel flow falls faster , so SFC improves below 15:1 Economy cruise mixtures of about 18:1 are used at moderate power The slower burn needs the ignition advanced so peak pressure still comes just after TDC Exam trap: a weak mixture needs advance, not retard
15:1 burns fast
18:1 burns slowly
same time after the spark · grey dots: nitrogen and spare air
-60
-30
TDC
+30
+60
+90
0
20
40
60
crank angle from TDC, degrees
cylinder pressure, bar
15:1, spark 25° BTDC
18:1, spark 25°: late and low
18:1, spark advanced to 35°
Chapter 7 · Mixture
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
A weak mixture has extra air, and most of that air is nitrogen, which takes no part in burning. It gets in the way, so the flame front crosses the cylinder more slowly and the gas burns at a lower temperature. The power falls, but the fuel flow falls even faster, and the cooler burning wastes less heat, so specific fuel consumption improves as you weaken below fifteen to one. That is why economical cruising at moderate power can use mixtures as weak as about eighteen to one. There is a catch. If the charge takes longer to burn, the peak pressure would arrive too late, with the piston already well down the cylinder. To put it back just after top dead centre, the spark must fire earlier. Watch the timing dial: here the spark is advanced to thirty-five degrees before the top, and the crank stops right at that moment, as the plug fires early and the piston is still rising. Remember: weak mixtures need advance, never retard.
Part 2 · Power and economy
Too weak: hot valves, popping back, overheating The charge may still be burning when the exhaust valve opens The exhaust valve meets flame: it can burn, crack or distort At the overlap the hot gas can light the fresh charge : popping back through the induction Heat not turned into work goes into the walls: overheating , high CHT At high power an over-weak mixture also invites detonation
still burning as the exhaust valve opens
popping back
into the induction
exhaust valve
burns or cracks
heat not turned into work goes to the cylinder walls: overheating
Chapter 7 · Mixture
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Weaken the mixture too far and the slow burning becomes dangerous. The charge may still be burning when the exhaust valve opens near the end of the power stroke. In the scene the crank stops just as the exhaust valve opens; imagine that gas still alight. Flame then rushes past the valve, and the exhaust valve, already the hottest part of the engine, can burn, crack or distort. A moment later, at the overlap, the inlet valve opens while the gas is still hot enough to light the fresh charge in the inlet port, and the engine pops back through the induction manifold. Meanwhile, heat that was released too late to push the piston is not turned into work, so it goes into the cylinder walls and the cooling system has to get rid of it. The result is overheating and high cylinder head temperatures. And at high power an over-weak mixture also brings the engine closer to detonation.
Part 2 · Power and economy
Too rich: smoke, soot and wasted fuel All the oxygen is used ; spare fuel is wasted or forms carbon monoxide Very rich: unburnt carbon leaves as black smoke , with orange-red flame at the exhaust Sooty, fouled plugs , rough running, high SFC; extreme richness causes a rich cut A rich mixture runs cooler : lower CHT and EGT Weak signs: drop in RPM , rough running, high CHT , popping back
Too rich
• black smoke (unburnt carbon)
• orange-red flame
• CO as well as CO₂
• sooty, fouled plugs
• higher fuel consumption
About right / weak
• clear exhaust
• blue flame
• CO₂ and H₂O
• clean, light-grey plugs
• lower fuel consumption
A rich mixture is cooler-burning; the extra fuel absorbs heat as it evaporates
Chapter 7 · Mixture
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Now the other way. In a rich mixture all of the oxygen is consumed, which is why a slightly rich mixture loses so little power. The spare fuel cannot burn completely: some of the oxygen is shared out so that carbon monoxide forms as well as carbon dioxide, and in a very rich mixture some carbon does not burn at all and leaves the exhaust as black smoke, with an orange-red flame. The plugs become sooty and can foul, the engine may run roughly, and specific fuel consumption goes up. Taken to the extreme, the mixture is too rich to burn and the engine stops in a rich cut. On the good side, a rich mixture runs cooler, because the extra fuel absorbs heat as it evaporates. Compare the signs of a weak mixture: a drop in R P M, rough running, high cylinder head temperature and popping back through the induction.
Part 3 · Phases of flight
How the mixture requirement changes with power
0
20
40
60
80
100
8:1
9:1
10:1
11:1
12:1
13:1
14:1
15:1
16:1
17:1
18:1
Engine power, % of maximum
Air : fuel ratio (up = weaker)
15:1 chemically correct
start / idle: rich
cruise, leaned: weak (economy)
full-rich setting
climb ≈ 11:1
take-off ≈ 10:1
The solid line is what the engine wants; the carburettor provides it with its idle system, main jet, mixture control and power enrichment.
Chapter 7 · Mixture
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
This curve shows what the engine needs across its power range. At starting and idling the requirement is rich, around eleven to one. As power rises into the cruise range, roughly forty to seventy-five per cent, the engine is happiest on a weak, economical mixture of around sixteen to one, provided the pilot leans it. The dashed grey line is what a typical full-rich setting delivers through the cruise, about twelve and a half to one, which wastes fuel. Then, above cruise power, the requirement swings back towards rich: about eleven to one for the climb and about ten to one for take-off at maximum power. So there are three regions to remember: rich at the bottom, weak in the middle, rich at the top. In the next chapter you will see which part of the carburettor looks after each region.
Part 3 · Phases of flight
Starting and slow running need a rich mixture Fuel burns only as vapour mixed with air A cold engine vaporises only the lightest fractions of the fuel: extra fuel needed At low RPM the exhaust gas is slow: with valve overlap some is drawn back into the cylinder That dilutes the fresh charge; a richer mixture keeps it burning smoothly Hence the slow-running jet is sized for a rich mixture
Cold engine
Low RPM
only the lightest
fractions vaporise
→ add more fuel
slow gas, overlap:
exhaust dilutes charge
→ add more fuel
Chapter 7 · Mixture
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
There are two reasons why starting and slow running need a rich mixture. First, fuel only burns as vapour mixed with air. In a cold engine there is little heat to help the fuel evaporate, so only its lightest fractions turn to vapour and the rest stays as droplets. To be sure there is enough vapour to burn, you supply extra fuel. Second, look at the valve timing. The exhaust valve closes late, after top dead centre, to use the momentum of the fast exhaust gas to scavenge the cylinder. At low R P M that gas is slow. In the scene the crank stops at the overlap, with the inlet valve and the exhaust valve both slightly open. At idle some burnt gas stays in the cylinder, and some is even drawn back in by the descending piston. That dilutes the fresh charge, and only a richer mixture will keep it burning smoothly.
Part 3 · Phases of flight
Take-off: full rich, about 10 to 1 Maximum power: mixture fully rich , about 10:1 The extra power comes from a greater mass of charge (full throttle, high RPM), not from the extra fuel The spare fuel evaporates and cools the charge: it keeps detonation away Otherwise wasted: not enough oxygen to burn it; CO forms, black smoke if very rich Leaning at take-off power risks detonation and overheating (except as the flight manual allows at high airfields)
Cruise, 65%
Take-off, 100%
Mass of charge per minute (throttle and RPM)
→ power comes from MORE CHARGE, not from more fuel
Mixture ≈ 10:1 — the extra fuel:
• evaporates and cools the charge → no detonation
• partly unburnt: CO formed, black smoke if very rich
• is otherwise wasted (no oxygen left to burn it)
Chapter 7 · Mixture
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
For take-off you want maximum power, and the mixture control goes fully rich, giving about ten to one. It is tempting to think the extra fuel makes the extra power, but it does not. The power comes from a greater mass of charge entering the cylinders each minute, because the throttle is wide open and the R P M is high; in the scene the throttle valve swings fully open. There is nowhere near enough oxygen to burn all that extra fuel. What it does is evaporate and cool the charge, keeping the gas temperature down and holding detonation away at the very moment the engine is working hardest. The fuel that does not burn properly forms carbon monoxide, and if the mixture is very rich, black smoke. So the rule is simple: maximum power, fully rich. Only at high airfields, and only as the flight manual says, may you lean for take-off.
Part 3 · Phases of flight
Climb: rich, about 11 to 1 Power = RPM × mean effective pressure : both are high in the climb Higher pressure and temperature in the cylinder raise the tendency to detonate Enrich to about 11:1 : the extra fuel cools the charge as it vaporises Low airspeed in the climb also means less cooling air : watch CHT At height, a carburettor mixture richens by itself : lean as the manual allows Power ∝ RPM × mean effective pressure High RPM ≈ 2500–2700 High pressure and temperature closer to DETONATION enrich to ≈ 11:1 fuel evaporates and cools the charge
Chapter 7 · Mixture
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
Climbing power is less than take-off power, but it is held for much longer. Engine power is the product of the R P M and the mean effective pressure in the cylinders during the cycle, and in the climb both are high. Higher speed and pressure mean higher gas temperatures, and so a stronger tendency to detonate. The answer is again the cooling effect of extra fuel: for the climb the mixture is enriched to about eleven to one, and the fuel that evaporates keeps the charge temperature down. There is a second reason to be careful. The climb is flown at a low airspeed, so less cooling air flows through the cowling, and cylinder head temperatures can creep up. Keep an eye on them. Finally, as the aircraft gains height, a carburettor mixture becomes richer all by itself, as we will see next, so in a long climb the flight manual may tell you to lean progressively.
Part 3 · Phases of flight
Altitude makes a carburettor mixture richer With height the air density falls , so less mass of air enters for the same throttle The venturi pressure drop falls too, but fuel flow follows its square root : it falls less Result: the mixture becomes progressively richer with altitude Example: set 15:1 at sea level → about 12.9:1 at 10 000 ft if untouched The pilot moves the mixture control towards weak as altitude increases
0
5000
10000
15000
11:1
12:1
13:1
14:1
15:1
Pressure altitude, ft
Air : fuel ratio, mixture untouched
15.0:1
13.9:1
12.9:1
11.9:1
air mass ∝ density ρ; fuel flow ∝ √(venturi Δp)
so fuel/air grows as 1/√σ: at 10 000 ft σ = 0.74,
mixture 16% richer → lean it with the mixture lever
Chapter 7 · Mixture
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
As you climb, the air gets thinner, so for the same throttle opening a smaller mass of air goes into the engine. The carburettor measures air by the pressure drop in its venturi, and that drop is smaller in thin air. But the fuel flow through the jet does not fall in step: it follows the square root of the pressure drop, while the air mass falls with the density. So the fuel to air ratio grows as one over the square root of the relative density. Here is a worked example. Set fifteen to one at sea level and leave it. At ten thousand feet the relative density is about nought point seven four, the mixture is about sixteen per cent richer, and you are running at roughly twelve point nine to one, wasting fuel and fouling plugs. So, as altitude increases, the pilot moves the mixture lever towards weak; in the scene the mixture needle closes part-way and less fuel reaches the jet and the venturi.
Part 3 · Phases of flight
Cruise: economy, endurance and range In the cruise only moderate power is needed, so it should be produced with the least fuel . Typical choices:
Best power (rich) cruise About 12.5:1 , slightly rich of peak EGT. A little faster; cooler; higher fuel flow.
Best economy (weak) cruise Weaker than 15:1, about 16–18:1 . Lowest SFC: the setting for maximum range and endurance .
Never at 15:1 at high power Peak EGT and the hottest combustion: closest to detonation . Use only as a reference while leaning.
Lean only at cruise power Normally at or below about 75% power, as the flight manual allows.
Go rich before power changes Return to fully rich before increasing power, and for descent and landing.
Move the lever slowly Lean in small steps and let the readings settle; over-leaning brings rough running and high CHT.
Chapter 7 · Mixture
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
In the cruise the engine only needs moderate power, so the aim is to produce it with the least possible fuel. There are two common choices. Best power cruise is around twelve and a half to one, slightly rich of the exhaust temperature peak: you go a little faster, the engine runs cooler, but the fuel flow is higher. Best economy cruise is weaker than chemically correct, about sixteen to eighteen to one. It gives the lowest specific fuel consumption, so it is the setting for the longest range and the longest endurance; if an exam asks how to set the mixture for maximum endurance, the answer is weak. Never sit at fifteen to one at high power, because that is the hottest combustion and the closest to detonation. Lean only at cruise power, usually at or below about seventy-five per cent. Return to fully rich before any power increase. And move the lever slowly, in small steps.
Part 4 · Leaning with EGT
The exhaust gas temperature gauge A thermocouple : two different metals joined; the junction gives a voltage proportional to temperature The probe sits in the exhaust pipe of the hottest cylinder , usually the one running leanest The gauge is calibrated in degrees; a movable reference pointer marks the peak More accurate than leaning by RPM (fixed-pitch propeller) or airspeed Multi-probe systems show every cylinder
1
2
3
4
leanest / hottest cylinder
thermocouple probe
EGT
°C
Two different metals joined:
voltage ∝ temperature
blue pointer: reference
set at the peak
Chapter 7 · Mixture
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
The most accurate way to set the mixture is with the exhaust gas temperature gauge. Its sensor is a thermocouple: two wires of different metals joined at a hot junction. The junction produces a small voltage that is directly proportional to its temperature, and the cockpit gauge measures that voltage and shows it as degrees. A single probe is fitted in the exhaust pipe of the hottest cylinder, usually the one that receives the weakest mixture, so it is the first to show trouble when you lean. Many gauges have a second, movable pointer that you set at the peak as a reference. Without an exhaust gas temperature gauge you can still lean by watching the R P M with a fixed-pitch propeller, or the airspeed, which both rise as the mixture approaches the most powerful setting and fall again beyond it. Modern engine monitors take this further and show a reading for every cylinder.
Part 4 · Leaning with EGT
Leaning to peak, then rich or lean of peak
10
11
12
13
14
15
16
17
18
19
20
500
600
700
800
Air : fuel ratio (leaning →)
EGT, °C
peak EGT ≈ 15:1 (not used: detonation)
rich cruise: "50 °C rich of peak"
economy (lean of peak,
per flight manual)
CHT (dashed)
← richer: cooler exhaust
Lean slowly to find the peak, then richen by the drop the flight manual specifies. Return to fully rich whenever power is changed.
Chapter 7 · Mixture
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what you see while leaning. Start fully rich and move the mixture lever slowly towards weak. The exhaust gas temperature rises, because less and less surplus fuel is cooling the gas, and it peaks at about fifteen to one, where all the air and fuel are burnt and the heat release is greatest. That peak is a reference, not a setting, because it is close to detonation at any real power. For a rich cruise you now move back towards rich until the temperature has dropped by the amount the flight manual specifies, for example fifty degrees rich of peak. For economy, the manual may instead specify a drop on the weak side. As you weaken beyond the chemically correct ratio, the exhaust temperature falls; in this course the cylinder head temperature rises a little further before it too falls, and excessive weakening lowers both. Thermal efficiency improves as the mixture is weakened below fifteen to one, which is why specific fuel consumption falls.
Part 5 · Aero-diesels
Aero-diesels run lean and need no mixture lever Air enters unthrottled : the cylinder always takes in a full charge of air Power is set by the amount of fuel injected , so diesels run lean overall Ignition by the heat of compression : no spark, so no detonation problem of the petrol kind Higher running temperatures : a reliable cooling system is essentialSingle lever : FADEC sets fuel, timing and propeller; no mixture lever
injector (FADEC timed)
air: no throttle
one lever
• runs lean overall
• no mixture lever
• no detonation problem
• hotter: good cooling needed
Chapter 7 · Mixture
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
Aero-diesel engines, which burn jet fuel or diesel in light aircraft, work quite differently. Their air supply is not throttled at all, so every cylinder always takes in a full charge of air. The power is set purely by how much fuel is injected, so the overall mixture is lean, with plenty of spare oxygen. The fuel is lit by the heat of compression, not by a spark, so the detonation problems of a petrol engine do not arise in the same way. Diesels do run hotter, though, so they need a reliable and effective cooling system. And because the electronic control unit, the FADEC, meters the fuel and sets the timing for you, there is no mixture lever. The pilot uses a single power lever, rather like some turboprops, and the computer looks after the rest.
Exam focus
Mixture numbers and traps Question asks… Answer Why Chemically correct ratio 15:1 air:fuel by mass Not by volume, not fuel:air 15:1 Burnable range 8:1 to 20:1 Outside it the mixture will not burn Mixture for maximum power / take-off Fully rich , about 10:1Cooling; power comes from charge mass Mixture for maximum endurance or range Weak Lowest specific fuel consumption 9:1 is… Rich Smaller air number = more fuel Climbing without leaning (carburettor) Mixture becomes richer Lean towards weak as altitude increases Weak mixture and ignition timing Advance itSlower burning Enriching the mixture SFC increases Fuel flow rises faster than power
Chapter 7 · Mixture
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Let us gather the favourite exam points. The chemically correct ratio is fifteen to one, air to fuel, by mass. Watch out for options that say fuel to air, or by volume. A mixture burns only between about eight to one and twenty to one. Maximum power and take-off: fully rich, about ten to one, and the extra power comes from the mass of the charge, not the fuel. Maximum endurance or range: weak, because that gives the lowest specific fuel consumption. Nine to one is rich, because the smaller the air number, the more fuel. If you climb with a carburettor and do not touch the mixture, it gets richer, so you move the lever towards weak. A weak mixture burns slowly, so the ignition must be advanced, not retarded. And enriching the mixture increases the specific fuel consumption.
Summary
Mixture in six lines 15:1 by mass Chemically correct; burns only between 8:1 and 20:1; hottest, so not used at power.
Rich for power About 12.5:1 best power; 11:1 climb; 10:1 take-off. Spare fuel cools and stops detonation.
Weak for economy Lowest SFC around 16–18:1, needs spark advance; maximum range and endurance.
Too weak, too rich Weak: overheating, burnt exhaust valves, popping back. Rich: black smoke, CO, fouled plugs.
Altitude A carburettor richens as density falls: lean as you climb, fully rich before power changes.
EGT and diesel Peak EGT at 15:1; set by a specified drop. Diesels: unthrottled, lean, single lever.
Chapter 7 · Mixture
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
To sum up. The chemically correct mixture is fifteen to one by mass, and a mixture only burns between about eight and twenty to one. Fifteen to one burns hottest, so it is not used at power. For power we go rich: about twelve and a half to one for best power, eleven to one for the climb and ten to one for take-off, with the spare fuel cooling the charge and keeping detonation away. For economy we go weak, around sixteen to eighteen to one, with the spark advanced, giving the lowest specific fuel consumption for range and endurance. Too weak means overheating, burnt exhaust valves and popping back; too rich means black smoke, carbon monoxide and fouled plugs. A carburettor richens with altitude, so lean as you climb and go fully rich before power changes. The exhaust gas temperature peaks at fifteen to one, and diesels need no mixture lever at all.