Engines · Chapter 6
Piston Engine Fuel and Fuel Systems Avgas grades and colours, the properties that matter, how fuel should burn, and what detonation, octane ratings, lead and pre-ignition are all about.
100LL
100
the right fuel, burning at the right rate
© 2026 eatpl.in. For the personal study of eatpl.in students only. Do not copy or distribute.
e-books by eatpl.in · © 2026 · Do not copy or distribute
Chapter six is about the fuel itself. An aero piston engine is designed around one grade of fuel, and the wrong grade, or the right grade burning the wrong way, can wreck it within minutes. In this lesson we look at where Avgas comes from and how its grades are told apart by colour, how to turn litres or gallons into weight, what calorific value, volatility and stability mean, and how the charge should burn. Then we tackle the big one for the exam: detonation, what causes it, how it is prevented, and how octane ratings, performance numbers and lead additives fight it. We finish with pre-ignition and a blocked tank vent.
Roadmap
From crude oil to a smooth power stroke
Crude oil
refined and
cracked
Avgas
grades and
colours
Properties
CV, volatility,
stability
Combustion
flame rate,
timing
Detonation
octane, PN,
TEL
1 · The fuel Where Avgas comes from, its grades, colours and lead, and how much it weighs.
2 · Properties Calorific value, volatility and boiling at altitude, vapour lock, stability, sulphur.
3 · Combustion Burning, not exploding: flame rate, timing, mixture.
4 · Detonation Causes, effects and cures; octane, performance numbers, lead, pre-ignition.
Chapter 6 · Piston Engine Fuel and Fuel Systems
2
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is our route through the fuel chapter. Crude oil is refined and cracked into many products, one of which is aviation gasoline, Avgas. Its grades are told apart by colour and by a pair of numbers called the performance number. Then we look at the properties that matter in an engine: how much heat the fuel gives, how easily it evaporates, and whether it keeps in storage. Next comes combustion: how the charge should burn, at what rate, and why the spark timing depends on speed and mixture. The last and biggest part is detonation, the uncontrolled explosion of the last part of the charge. We look at its causes, effects and cures, and at the octane ratings, performance numbers and lead additives that fight it. We end with pre-ignition and with what a blocked fuel tank vent does.
Part 1 · The fuel
Where Avgas comes from Aviation fuels come from crude (mineral) oil : blends of hydrogen and carbon (hydrocarbons) Refining and cracking produce gasoline, kerosene (jet fuel) and diesel from the same oil Piston aero engines burn aviation gasoline: Avgas Some authorities allow approved aircraft to use car petrol, Mogas Avgas dispensing equipment is colour-coded red to prevent cross-contamination (Jet A-1: black)
Refinery
distilling + cracking
Gases
Avgas / Mogas (gasoline)
Kerosene: Jet A-1
Diesel
Heavy oils
Avgas: hydrocarbons, a blend of hydrogen and carbon.
Avgas dispensing equipment is coded RED
(Jet A-1 equipment: black) to stop mix-ups.
Chapter 6 · Piston Engine Fuel and Fuel Systems
3
e-books by eatpl.in · © 2026 · Do not copy or distribute
The fuel for aircraft piston engines comes from crude, or mineral, oil. It is a blend of hydrocarbons, compounds of hydrogen and carbon. In the refinery the crude is distilled and then cracked, a process that breaks big molecules into smaller ones, to make a whole family of products: gases, gasoline, kerosene, diesel and heavy oils. Jet fuel and diesel come from the same oil as the gasoline. Piston aero engines burn aviation gasoline, called Avgas. Some aviation authorities also allow certain approved aircraft to use ordinary car petrol, known as Mogas, under strict conditions. Because putting the wrong fuel into an aircraft can be disastrous, the equipment used to dispense Avgas is colour-coded red, while equipment for the kerosene-type fuel, Jet A-1, is coded black. Always check the grade before refuelling.
Part 1 · Grades
Avgas grades: told apart by colour
AVGAS 100LL
PN 100/130
Blue
Low lead
SG ≈ 0.72
AVGAS 100
PN 100/130
Green
High lead
SG ≈ 0.72
AVGAS 80
PN 80/87
Red
Very low lead
SG ≈ 0.72
100 and 100LL have the same anti-knock value (100/130) but different colours . Never use a lower grade than specified; if the correct grade is unavailable, use a higher one.
Chapter 6 · Piston Engine Fuel and Fuel Systems
4
e-books by eatpl.in · © 2026 · Do not copy or distribute
Avgas is made to a strict specification, and within it there are grades. Here are the three classic ones. Avgas one hundred L L, for low lead, is dyed blue and has a performance number of one hundred over one hundred and thirty. It is the grade you will meet almost everywhere today. Avgas one hundred has exactly the same performance number, one hundred over one hundred and thirty, but contains more lead and is dyed green. Avgas eighty, performance number eighty over eighty-seven, has very little lead and is dyed red. All have a specific gravity of about nought point seven two. The favourite exam trap: one hundred and one hundred L L have the same anti-knock value but different colours. And the golden rule: never use a lower grade than the engine is designed for, because it may detonate. If the correct grade is not available, use a higher one.
Part 1 · Weight
From volume to weight: specific gravity Specific gravity (SG) : the density of the fuel compared with waterAvgas SG is about 0.72 ; Jet A-1 about 0.80 One Imperial gallon of water weighs 10 lb ; one litre has a mass of 1 kg Weight = volume × water weight per unit × SG Fuel is loaded by volume but limited by weight : always convert
Specific gravity turns volume into weight
SG = density of the fuel ÷ density of water
Example 1 · Imperial gallons
One Imperial gallon of water weighs 10 lb
100 gal × 10 lb × 0.7 = 700 lb
Example 2 · litres
One litre of water has a mass of 1 kg
150 L × 0.72 = 108 kg of Avgas
Water
1.00
Jet A-1
0.80
Avgas
0.72
Chapter 6 · Piston Engine Fuel and Fuel Systems
5
e-books by eatpl.in · © 2026 · Do not copy or distribute
Fuel is pumped in by volume, but aircraft performance and loading depend on weight, so you must be able to convert. The tool is specific gravity, the density of the fuel compared with the density of water. Avgas has a specific gravity of about nought point seven two; the kerosene-type fuel Jet A-1 about nought point eight. Two handy facts: one Imperial gallon of water weighs ten pounds, and one litre of water has a mass of one kilogram. So, in the classic exam question, a hundred Imperial gallons of fuel with a specific gravity of nought point seven weighs a hundred times ten times nought point seven, which is seven hundred pounds. And a hundred and fifty litres of Avgas at nought point seven two has a mass of a hundred and eight kilograms. Remember that specific gravity changes a little with temperature, so warm fuel weighs slightly less per litre.
Part 2 · Properties
Calorific value: how much heat the fuel gives Calorific value : the heat energy released when a given mass of fuel burns completelyMeasured per unit mass: MJ/kg (older: British Thermal Units per pound) Depends on composition: a high hydrogen content gives a high value Per unit volume , the denser fuel carries more energy Jet A-1 and diesel: slightly less per kg than Avgas, but about 10% more per litre
Calorific value: heat released on burning
Per kilogram (MJ/kg)
Avgas
43.5
Jet A-1
43.2
Per litre (MJ/L) = SG × MJ/kg
Avgas
0.72 × 43.5 = 31.3
Jet A-1
0.80 × 43.2 = 34.6
High hydrogen content gives a high value per kg.
Fuel is bought by volume: the denser fuel carries
about 10% more energy per litre, so better range.
Older units: British Thermal Units per pound.
Chapter 6 · Piston Engine Fuel and Fuel Systems
6
e-books by eatpl.in · © 2026 · Do not copy or distribute
The calorific value of a fuel is the amount of heat energy released when a given mass of it burns completely. It is usually quoted per kilogram, in megajoules, or in older units, British Thermal Units per pound. It depends on what the fuel is made of; hydrogen releases a lot of heat, so fuels rich in hydrogen have a high calorific value. Avgas gives about forty-three and a half megajoules per kilogram, and Jet A-1 almost the same, about forty-three. But we buy and carry fuel by volume, and a litre of the denser fuel has more mass in it. Multiply specific gravity by calorific value: Avgas gives about thirty-one megajoules per litre, Jet A-1 about thirty-four and a half, roughly ten per cent more. So, per litre, the denser fuel carries more energy, which gives diesel-engined aircraft better range from the same tanks.
Part 2 · Properties
Volatility and low-pressure boiling Volatility : how readily a liquid turns to vapourIt decides how well the fuel mixes with the air ; some droplets still evaporate in the induction system A liquid boils when its vapour pressure is greater than the pressure on its surface Atmospheric pressure falls with altitude, so fuel boils at a lower temperature higher up This is low-pressure boiling
0k
5k
10k
15k
20k
25k
30k
20
40
60
80
100
altitude (ft, ISA)
pressure (kPa)
atmospheric pressure
Avgas vapour pressure (warm fuel)
A liquid boils when its vapour pressure exceeds the
pressure on it. Warm Avgas can start to boil from
about 19 000 to 25 000 ft: low-pressure boiling.
Band: typical Avgas vapour pressure limits (38–49 kPa at 38 °C).
Chapter 6 · Piston Engine Fuel and Fuel Systems
7
e-books by eatpl.in · © 2026 · Do not copy or distribute
Volatility is how readily a liquid changes into vapour, by being heated or by evaporating into a gas. Fuel is added to the air in the carburettor, and how well it mixes depends largely on its volatility. Even so, the time available is so short that some fuel stays as tiny droplets and finishes evaporating in the induction system. Now, a liquid boils when its vapour pressure is greater than the pressure acting on its surface. At sea level that takes a lot of heat, but atmospheric pressure falls as you climb. The graph compares atmospheric pressure with the typical vapour pressure of warm Avgas. The lines cross at about nineteen to twenty-five thousand feet, so warm fuel can start to boil up there, at a much lower temperature than on the ground. That is called low-pressure boiling, and it is one reason fuel tanks of high-flying aircraft may need boost pumps or pressurisation.
Part 2 · Properties
Too volatile: vapour lock, cavitation and icing High volatility means evaporation losses from the tanks Fuel can boil at the low-pressure inlet of the pump : cavitation and vapour lock , interrupting flow More evaporation in the carburettor means more cooling: carburettor icing is more likely Mogas is more volatile than Avgas: vapour lock and carburettor icing are much more likely Too little volatility: poor mixing, hard starting
Tank: evaporation losses
Pump inlet: vapour bubbles
(cavitation) and vapour lock
fuel flow
interrupted
Too volatile: vapour lock, cavitation, tank losses,
and a greater risk of carburettor icing.
Too little volatility: poor mixing, hard starting.
Mogas is more volatile than Avgas: more vapour lock and icing.
Chapter 6 · Piston Engine Fuel and Fuel Systems
8
e-books by eatpl.in · © 2026 · Do not copy or distribute
A fuel that is too volatile causes trouble. In the tanks, more of it simply evaporates away. In the fuel lines, the lowest pressure is at the inlet side of the pump, and there volatile fuel can boil, forming vapour bubbles around the pump impeller. That is cavitation, and if the bubbles collect they block the flow: a vapour lock, which can stop the engine. In the carburettor, evaporating fuel takes heat from the air, as the scene shows. The more volatile the fuel, the faster it evaporates and the colder the venturi gets, so carburettor icing becomes more likely. This is why Mogas, car petrol, needs care: it is more volatile than Avgas, so both vapour locking and carburettor icing are much more likely. On the other hand, a fuel with too little volatility mixes poorly with the air and makes starting difficult.
Part 2 · Properties
Stability and sulphur Stability Some hydrocarbons in gasoline readily combine with oxygen . Oxidised, they form heavy, gummy, resinous deposits and corrosive compounds that clog jets and filters. Oxidation inhibitors are added to keep the fuel stable in storage.
Sulphur content Burnt sulphur forms sulphur dioxide , which combines with water in the exhaust to make sulphurous acid , very corrosive to the exhaust system. Sulphur is kept extremely low : the exam figure is a maximum of 0.001% .
Water Fuel can carry dissolved and free water. Drain and check samples before flight: cloudy fuel usually means water.
Good fuel, in short High calorific value, the right volatility, stable in storage, low in sulphur and free of water and dirt, with the anti-knock rating the engine needs.
Chapter 6 · Piston Engine Fuel and Fuel Systems
9
e-books by eatpl.in · © 2026 · Do not copy or distribute
Two more properties matter for keeping the engine and its fuel system healthy. The first is stability. Some of the hydrocarbons in gasoline have a strong attraction for oxygen. When they meet air, they oxidise and turn into heavy, resinous, gummy compounds and corrosive substances, which can clog jets and filters. To stop this, oxidation inhibitors are added to the fuel. The second is sulphur. When sulphur burns it makes sulphur dioxide, which combines with the water vapour in the exhaust to form sulphurous acid, and that is extremely corrosive to the exhaust system. So the sulphur content is kept extremely low; the figure usually quoted in exams is a maximum of nought point nought nought one per cent. Water in fuel is another enemy, which is why you drain and inspect fuel samples before flight. Cloudy fuel usually means water.
Part 3 · Combustion
Combustion: a controlled burn, not an explosion Gasoline is about 84% carbon and 16% hydrogen by weight; air about 78% nitrogen, 21% oxygen Carbon burns to carbon dioxide , hydrogen to water vapour Nitrogen takes no part, but it is most of the gas that is heated and expandsNitrogen also slows the burning: without it, combustion would be an explosion The chemically correct mixture is about 15 : 1 air to fuel by weight
Fuel + air → carbon dioxide + water
Fuel by weight
carbon 84.2%
H 15.8%
Air by volume
nitrogen 78%
O₂ 21%
C + O₂ → CO₂ · H₂ + ½O₂ → H₂O
Nitrogen takes no part, but it:
• is most of the gas that is heated and expands
• slows the burning: without it, an explosion
Worked: oxygen for 1 kg of fuel
carbon 0.842 × 32/12 + hydrogen 0.158 × 32/4 = 3.51 kg O₂
air is 23.2% oxygen by weight: 3.51 ÷ 0.232 ≈ 15 kg of air
Chemically correct mixture ≈ 15 : 1 air to fuel by weight
Chapter 6 · Piston Engine Fuel and Fuel Systems
10
e-books by eatpl.in · © 2026 · Do not copy or distribute
Combustion in a cylinder is a controlled rate of burning, not an explosion. The charge is gasoline vapour, about eighty-four per cent carbon and sixteen per cent hydrogen by weight, mixed with air, which is about seventy-eight per cent nitrogen, twenty-one per cent oxygen and one per cent other gases. When it burns completely, the carbon combines with oxygen to make carbon dioxide, and the hydrogen to make water vapour. The nitrogen takes no part in the chemistry, but it matters a great deal. It is most of the gas that gets heated and expands to push the piston, and it slows down the burning. Without nitrogen, the temperature and pressure would rise far too quickly to be harnessed. The worked example uses the composition to find how much air is needed to burn a kilogram of fuel completely: about fifteen kilograms. So the chemically correct mixture is about fifteen to one by weight.
Part 3 · Combustion
Flame rate and the timing of peak pressure
60° B
40° B
20° B
TDC
20° A
40° A
60° A
0
25
50
75
crank angle (degrees, TDC = 0)
cylinder pressure (relative)
no firing (compression only)
normal: peak ≈ 9° ATDC
spark 25° BTDC
Normal flame rate about 60–80 ft/s : a smooth rise to peak pressure at about 8–10° ATDC . Peak pressure at or before TDC would tend to drive the engine backwards.
Chapter 6 · Piston Engine Fuel and Fuel Systems
11
e-books by eatpl.in · © 2026 · Do not copy or distribute
The flame rate is the speed at which the mixture burns in the cylinder. In normal combustion the spark lights the compressed charge and the flame spreads rapidly and steadily, at about sixty to eighty feet per second, giving a smooth rise in temperature and pressure. The graph shows it. The grey dashed line is the pressure from compression alone. The green line is a normal firing cycle: the spark at twenty-five degrees before top dead centre, then a steady rise to a peak at about nine degrees after. That is where we want it, at eight to ten degrees after top dead centre. There the crank is only just past top dead centre, so the volume is still close to its minimum and the pressure is at its highest, yet the piston has started down and the crank can turn the push into torque. If maximum pressure came at or before top dead centre, it would push against the rising piston, and the engine would tend to run backwards.
Part 3 · Combustion
Timing with speed and with mixture The flame rate is roughly constant, so burning takes about the same time at any RPM Low RPM: spark retarded , so peak pressure does not come before TDC High RPM: spark advanced , so peak pressure still comes at 8–10° ATDC A richer mixture or higher pressure burns slightly faster High power uses a rich mixture, so the spark is retarded slightly , or not advanced further
Low RPM: retard
TDC
spark 8° BTDC
peak 9° ATDC
High RPM: advance
TDC
spark 28° BTDC
peak 9° ATDC
Same burn time, ~2 ms: the faster crank sweeps
more degrees, so the spark must come earlier.
Rich mixture at full power burns faster: retard slightly.
Chapter 6 · Piston Engine Fuel and Fuel Systems
12
e-books by eatpl.in · © 2026 · Do not copy or distribute
Because the flame rate stays roughly the same, the burn takes about the same time whatever the engine speed. At low R P M the crank moves slowly during that time, so the spark must be retarded, otherwise maximum pressure would build up before the piston reaches top dead centre. At high R P M the piston moves much faster during the same burn, so the spark must be advanced to keep the peak at eight to ten degrees after. The scene stops the crank in the power stroke, just after the peak, with the burning charge driving the piston down. The flame rate does change a little. A richer mixture, or a higher pressure in the cylinder, burns faster. At high power every engine uses a rich mixture, to keep combustion stable and cool, and because that rich mixture burns faster, the spark is retarded slightly for full power, or at least not advanced any further.
Part 4 · Detonation
Detonation: the end gas explodes Detonation happens after the spark: unstable combustion The advancing flame front heats and compresses the unburnt end gas ahead of it Eventually the whole end gas reaches ignition point at the same instant and explodes The flame rate jumps from about 60–80 to about 1000 ft/s Its violence depends on how much end gas is left
The flame front crosses the chamber
spark
END GAS
heated and squeezed
by the advancing flame
Normal: steady flame front, about 60–80 ft/s
Detonation: the end gas ignites all at once,
about 1000 ft/s: a violent pressure wave
It happens AFTER the spark: unstable combustion.
Chapter 6 · Piston Engine Fuel and Fuel Systems
13
e-books by eatpl.in · © 2026 · Do not copy or distribute
Detonation, also called knocking, is a form of unstable combustion that happens after the spark. In normal burning, the flame front travels smoothly through the mixture, each layer heating the next so that it burns in turn. But as the flame advances it concentrates more and more heat on the unburnt mixture still ahead of it, which we call the end gas. At the same time, the burnt gases behind the flame have expanded, so the end gas is being compressed as well. If the heat and pressure become great enough, the whole of the end gas reaches its ignition point at the same instant and explodes. The flame rate leaps from about seventy feet per second to about a thousand, and the violence depends on how much end gas is left. The scene marks where the end gas waits: the far side of the chamber, often near the hot exhaust valve.
Part 4 · Detonation
Normal, detonating and pre-ignited combustion
60° B
40° B
20° B
TDC
20° A
40° A
60° A
0
25
50
75
crank angle (degrees, TDC = 0)
cylinder pressure (relative)
no firing (compression only)
normal: peak ≈ 9° ATDC
spark 25° BTDC
detonation: end gas explodes,
pressure spikes and rings
pre-ignition: lit early by a
hot spot; peak at or before TDC
Detonation: a violent pressure spike after the spark. Pre-ignition: burning starts before the spark, so the peak comes too early .
Chapter 6 · Piston Engine Fuel and Fuel Systems
14
e-books by eatpl.in · © 2026 · Do not copy or distribute
This graph puts three cycles side by side. The green line is normal combustion, peaking smoothly at about nine degrees after top dead centre. The red line is detonation. It starts exactly like the normal cycle, because detonation happens after the spark. But part way through, the end gas explodes: the pressure leaps in a sharp spike and then rings, as pressure waves bounce across the combustion chamber. Those pressure waves hammering on the walls are what you hear as the metallic knock or pinking. The purple dashed line is pre-ignition, which we cover at the end of the lesson. Here a hot spot lights the charge well before the spark, so the pressure rises early and peaks at or before top dead centre, fighting the rising piston. Both are destructive; both cost power.
Part 4 · Detonation
Effects and recognition of detonation Piston crown The explosion can burn the piston crown and eventually make it collapse .
Overheating The combustion chamber overheats; valves can split and distort, plug electrodes burn.
Shock loads The sudden pressure rise shock-loads pistons, rods and bearings: mechanical damage.
Power loss Peak pressure comes before the piston can use it; the piston works against a high back pressure .
Hard to hear The metallic knock is masked by propeller noise: in aircraft it may go unnoticed until too late.
Gauges Watch rising CHT and EGT . Both gauges are thermocouples : they make their own voltage.
Chapter 6 · Piston Engine Fuel and Fuel Systems
15
e-books by eatpl.in · © 2026 · Do not copy or distribute
What does detonation do? The explosion of the end gas can burn the piston crown and, if it goes on, make it collapse. The combustion chamber overheats, which can split and distort the valves and burn the spark plug electrodes. The sudden rise in pressure applies a shock load to the pistons, connecting rods and bearings, causing mechanical damage. And because the maximum pressure arrives before the piston is in the right position to use it, the piston has to work against a high back pressure, so power is lost. In a car you hear detonation as pinking, a metallic knocking. In an aircraft the noise of the propeller usually drowns it out, so serious damage can be done at high power before anyone notices. Your clues are the gauges: a rising cylinder head temperature and exhaust gas temperature. Both are thermocouple instruments, which generate their own voltage.
Part 4 · Detonation
What causes detonation Cause Why it promotes detonation Mixture too weak at high powerMore fuel for the same air allows more power without detonation; high power needs a rich mixture High charge temperature Carburettor heat at high power, overheated cylinders, high boost with very low RPM, over-compression in a supercharger Ignition too far advanced The charge is lit too early: higher temperatures and pressures in the end gas Poor cooling , carbon depositsCarbon (coke) on chamber surfaces holds heat: high cylinder head temperatures Cylinder head design Large chamber, poor plug and valve positions, high compression ratio, poor cooling: long flame travel Wrong fuel A grade with a lower anti-knock rating than the engine needs
Anything that raises the temperature or pressure of the end gas, or gives it more time , makes detonation more likely.
Chapter 6 · Piston Engine Fuel and Fuel Systems
16
e-books by eatpl.in · © 2026 · Do not copy or distribute
Detonation can be caused by one thing or a combination. A mixture that is too weak at high power is a classic: the more fuel there is for a given amount of air, the more power the engine can make without detonating, so high power needs a rich mixture. A high charge temperature is another: using carburettor heat at high power, overheated cylinders, very high boost at very low R P M, or over-compression in a supercharger. Ignition that is too far advanced lights the charge too early, raising the temperatures. Carbon deposits on the combustion chamber surfaces stop heat getting away and raise the head temperature. The design of the cylinder head matters: a big chamber, badly placed plugs and valves, a high compression ratio and poor cooling all give the end gas more time and heat. And, of course, using fuel of the wrong, lower grade. The common thread: temperature, pressure and time.
Part 4 · Detonation
Preventing detonation: less heat, pressure and time Compact combustion chamber : shorter flame travelTwo spark plugs : two flame fronts, shorter burning timeStart the flame near the exhaust valve (a hot spot), pushing the end gas towards cooler parts Same power at higher RPM (finer pitch) with a smaller throttle : lower cylinder pressure, less time Use a rich mixture at high power, avoid carb heat at high power, and use the correct grade
Large chamber, one plug
Compact, two plugs
long flame travel
half the travel
Less heat
rich at high power; no carb heat at high power
Less pressure
smaller throttle at higher RPM (finer pitch); sensible boost
Less time
compact chamber, two plugs, correct spark timing
Right fuel
the grade the engine was designed for, or higher
Chapter 6 · Piston Engine Fuel and Fuel Systems
17
e-books by eatpl.in · © 2026 · Do not copy or distribute
Since detonation needs heat, pressure and time, anything that reduces those helps. Designers use a compact combustion chamber, so the flame front has less distance to travel, and two spark plugs, so two flame fronts burn the charge in less time. If possible the flame is started near a hot spot such as the exhaust valve, so that the end gas is pushed away from the hottest part of the chamber and compressed into a cooler part, as the scene shows. The pilot can help too. The same power can be made at a higher engine speed by using a finer propeller pitch, with a smaller throttle opening; that lowers the cylinder pressure, and the higher speed cuts the time available for detonation. Fly high power with a rich mixture, do not use carburettor heat at high power, and always use the correct grade of fuel.
Part 4 · Anti-knock ratings
Octane rating: resistance to detonation Two pure reference fuels : iso-octane (rated 100 , resists knock) and normal heptane (rated 0 , knocks easily) The test fuel runs in a special single-cylinder engine under standard conditions It is matched with a blend of the two reference fuels that knocks the same Example: matches 95% iso-octane + 5% heptane → octane rating 95 The octane rating measures anti-knock value : resistance to detonation, not energy or volatility
Matching the test fuel
iso-octane 95%
heptane 5%
same knock as the test fuel → octane rating 95
Iso-octane
100
resists knock strongly
Normal heptane
0
knocks very readily
Octane rating = ANTI-KNOCK value:
resistance to detonation. Not energy, not volatility,
not resistance to pre-ignition or accidental ignition.
Above 100 (better than iso-octane): performance numbers,
measured against iso-octane with lead added.
Chapter 6 · Piston Engine Fuel and Fuel Systems
18
e-books by eatpl.in · © 2026 · Do not copy or distribute
The easiest way of controlling detonation is to improve the fuel, and to do that we need a way of measuring its resistance to knocking. Two chemically pure fuels are used as references. Iso-octane has very good combustion characteristics and hardly knocks at all, so it is given a rating of one hundred. Normal heptane detonates very readily and is rated zero. The fuel under test is run in a special single-cylinder test engine under standard conditions, and then blends of the two reference fuels are tried until one produces the same degree of detonation. If the matching blend is ninety-five per cent iso-octane and five per cent normal heptane, the test fuel has an octane rating of ninety-five. So the octane rating is a measure of the fuel’s anti-knock value, its resistance to detonation. It says nothing about the fuel’s energy content or its volatility, a common exam trap.
Part 4 · Anti-knock ratings
Two numbers: weak-mixture and rich-mixture ratings
0
20
40
60
80
100
120
140
mixture strength: weak ← → rich
knock-limited power (relative)
80: weak-mixture rating
87: rich-mixture rating
Grade 80/87
100: weak-mixture rating
130: rich-mixture rating
Grade 100/130
100/130: behaves as 100 with a weak mixture (cruise) and as 130 with a rich mixture (take-off and climb). Ratings above 100 are performance numbers .
Chapter 6 · Piston Engine Fuel and Fuel Systems
19
e-books by eatpl.in · © 2026 · Do not copy or distribute
The original octane tests used the mixture that gave the most detonation, but that is not how an aircraft engine runs all the time. Maximum detonation occurs with the economical, weak mixtures used in cruise, while rich mixtures are used for take-off and climb, and a rich mixture allows more power before knocking. So aviation fuel carries two ratings, sometimes called the performance number or performance index. Take one hundred over one hundred and thirty. The lower figure, one hundred, is the weak-mixture rating; the higher figure, one hundred and thirty, is the rich-mixture rating. With a weak mixture it behaves as a one-hundred-octane fuel, with a rich mixture as one hundred and thirty. Ratings above one hundred cannot be percentages of iso-octane, so they are performance numbers, measured against iso-octane with lead added. In practice it is still called a one-hundred-octane fuel.
Part 4 · Anti-knock ratings
Why high octane is worth having Better anti-knock fuel allows a higher compression ratio : more efficiency, better economy, more power It also allows higher induction pressure : much more power from a supercharger Power is proportional to the weight of mixture burned per unit time So the higher the compression ratio, the higher the octane rating required An engine designed for a grade must never be given a lower one
4
5
6
7
8
9
10
11
12
30
40
50
60
compression ratio
ideal thermal efficiency (%)
7:1 → 54.1%
9:1 → 58.5%
Higher compression ratio = higher efficiency and power
but a hotter, more compressed end gas:
so a higher octane rating is required.
Ideal (air-standard) values; real engines reach under 30%.
Supercharging raises charge pressure: also needs higher octane.
Chapter 6 · Piston Engine Fuel and Fuel Systems
20
e-books by eatpl.in · © 2026 · Do not copy or distribute
Why go to the trouble of high-octane fuel? Because it lets the engine squeeze the charge harder. The higher the pressure of the mixture before combustion, the higher the pressure of the burning gases, so the greater the power and the thermal efficiency. The compression ratio, the volume at bottom dead centre divided by the volume at top dead centre, sets that pressure, and the scene shows the piston moving between the two. The graph shows the ideal efficiency rising from about fifty-four per cent at seven to one to fifty-eight and a half at nine to one; real engines reach less than thirty, but the trend is the same. Squeeze harder, though, and the end gas gets hotter, so the higher the compression ratio, the higher the octane rating required. Good fuel also allows a supercharger to raise the induction pressure, increasing the weight of mixture burned each second, and power is proportional to that weight.
Part 4 · Additives
Tetra-ethyl lead and its scavenger Tetra-ethyl lead (TEL) is the main anti-knock additive: it reduces the risk of detonation It cuts the formation of peroxides , which make the end gas ready to explode Burning TEL leaves lead oxide , not volatile: it corrodes exhaust valves, seats and plug electrodes Ethylene dibromide turns it into lead bromide , which is volatile and leaves with the exhaustTEL raises the anti-knock rating; it does not raise calorific value or SG
Tetra-ethyl lead (TEL)
cuts peroxide formation: end gas less ready to explode
but burning TEL leaves lead oxide
not volatile: corrodes exhaust valves, seats and plug electrodes
so ethylene dibromide is added
turns it into lead bromide: volatile, leaves with the exhaust
Fuels better than iso-octane are rated against
leaded iso-octane: performance numbers above 100.
Lead deposits also add to plug fouling at low power.
Chapter 6 · Piston Engine Fuel and Fuel Systems
21
e-books by eatpl.in · © 2026 · Do not copy or distribute
Detonation can also be held off by adding small amounts of chemicals to the fuel, and the main one is tetra-ethyl lead, T E L. It works by reducing the formation of peroxides, unstable compounds that act like detonators in the end gas. So T E L decreases the risk of detonation and raises the anti-knock rating. But it has to be used carefully. When it burns, it forms lead oxide, which is not volatile at combustion temperatures, so it stays in the engine and corrodes the exhaust valves, their seats and the spark plug electrodes. To deal with that, ethylene dibromide is added as well. It changes the reaction so that lead bromide forms instead, which is volatile and is carried out with the exhaust gases. Exam trap: lead is added to improve the anti-knock value, not to increase the calorific value or the specific gravity.
Part 4 · Pre-ignition
Pre-ignition is not detonation Pre-ignition Detonation When Before the sparkAfter the sparkCause A local hot spot : glowing carbon, very hot plug points End gas heated and compressed by the flame until it explodes What happens Charge lit early: peak pressure at or before TDC End gas explodes at about 1000 ft/s: pressure spike Symptoms Rough running, running on after switch-off, loss of power Knock (often masked), rising CHT and EGT, loss of power Link Overheating from detonation can create the hot spots for pre-ignition Pre-ignition makes detonation more likely
Pre-ignition: the mixture is ignited by abnormal conditions in the cylinder before the normal ignition point .
Chapter 6 · Piston Engine Fuel and Fuel Systems
22
e-books by eatpl.in · © 2026 · Do not copy or distribute
Do not confuse pre-ignition with detonation. Pre-ignition is the ignition of the charge before the spark occurs. It is usually caused by a local hot spot in the combustion chamber, such as a lump of glowing carbon or overheated spark plug points, which lights the mixture early. The result is rough running and a loss of power, and because the hot spot does not need the spark, the engine may even keep running after the ignition is switched off, which is called running on. Detonation, by contrast, happens after a normal spark, when the end gas explodes. The two feed each other, though: the overheating caused by detonation can create the hot spots that cause pre-ignition, and pre-ignition, by lighting the charge early, makes detonation more likely. For the exam, the definition to remember is: the mixture is ignited by abnormal conditions within the cylinder before the normal ignition point.
Part 4 · Efficiency and alternatives
Thermal efficiency and kerosene-type fuels A gallon of fuel could do about 116 million ft-lb of work if none were wasted Heat is lost to cylinder walls and pistons, in the exhaust, and to friction: under 30% reaches the propeller Aero-diesels burn Jet A-1 (kerosene) : widely available, less volatile , less of a fire hazard Denser, so more energy per litre: better range and endurance But it waxes and thickens when cold: the fuel system needs heating
One gallon of fuel, fully used
≈ 116 275 000 ft-lb of work
useful work, under 30%
exhaust heat
walls, pistons, friction
Kerosene-type fuel (Jet A-1) for aero-diesels
+
less volatile: lower fire hazard, safer
+
widely available
+
denser: ~10% more energy per litre
−
slightly lower calorific value per kg
−
waxes and thickens when cold: needs fuel heating
Chapter 6 · Piston Engine Fuel and Fuel Systems
23
e-books by eatpl.in · © 2026 · Do not copy or distribute
How efficient is all this? The heat from burning one gallon of fuel could, in theory, do about a hundred and sixteen million foot-pounds of work if none of it were wasted. In practice a great deal of heat goes into the cylinder walls and piston crowns, the exhaust gases leave still very hot, and more work is absorbed by the engine’s internal friction. Under the best conditions, rather less than thirty per cent of the fuel’s heat becomes useful work at the propeller. That is one reason aero-diesels are attractive. They burn kerosene-type fuel such as Jet A-1, which is widely available, much less volatile and so less of a fire hazard than Avgas. Its calorific value per kilogram is slightly lower, but it is denser, so it carries more energy per litre, which gives better range and endurance. On the down side, it begins to wax and thicken at low temperatures, so the fuel system needs some form of heating.
Part 4 · The fuel system
Tank vents: what a blockage does Each tank is vented so that air can replace the fuel that is used If the vent is blocked , the pressure in the tank falls as fuel is drawn off The pump struggles against the falling pressure: flow falters and the engine can be starved A flexible or light tank can even collapse Check vents on the pre-flight inspection: insects, ice and dirt can block them
Vent clear
air replaces fuel
to the engine
steady flow
Vent blocked
pressure falls
as fuel is used
to the engine
flow falters, engine starves
A blocked vent: tank pressure FALLS as fuel is used;
the flow can stop and a flexible tank can even collapse.
Chapter 6 · Piston Engine Fuel and Fuel Systems
24
e-books by eatpl.in · © 2026 · Do not copy or distribute
Every fuel tank has a vent, so that as fuel is used, air can come in to take its place. Watch what happens when the vent is blocked, perhaps by an insect nest, ice or dirt. As the pump draws fuel off, nothing replaces it, so the pressure in the tank falls below atmospheric. The gauge shows it dropping. The pump now has to pull against that falling pressure, the flow falters, and eventually the engine can be starved of fuel. With a light or flexible tank, the pressure difference can even make the tank collapse. So the exam answer to a blocked vent is that the pressure in the tank falls as fuel is used. That is why checking that the fuel vents are clear is part of every pre-flight inspection.
Summary
What to take into the exam Grades 100LL blue , 100 green (both 100/130), 80 red (80/87). Never a lower grade; use a higher one if needed.
Weight SG ≈ 0.72. 100 Imp gal × 10 lb × 0.7 = 700 lb . Litres × SG = kg.
Properties CV = heat energy in the fuel. Volatile fuel: vapour lock, cavitation, carb ice (Mogas worse). Low-pressure boiling at altitude.
Combustion Controlled burn, 60–80 ft/s; peak 8–10° ATDC; advance with RPM; rich mixture burns faster.
Detonation After the spark: end gas explodes (~1000 ft/s). Caused by excessive temperature and pressure; weak mixture, high CHT.
Octane / PN Iso-octane 100, heptane 0. Rating = resistance to detonation . 100/130: weak 100, rich 130. Higher CR needs higher octane.
TEL Reduces detonation; ethylene dibromide removes lead as volatile lead bromide.
Pre-ignition, vents Pre-ignition: hot spot fires the charge before the spark. Blocked vent: tank pressure falls .
Chapter 6 · Piston Engine Fuel and Fuel Systems
25
e-books by eatpl.in · © 2026 · Do not copy or distribute
Here is what to take into the exam. Avgas one hundred L L is blue and one hundred is green, both one hundred over one hundred and thirty; Avgas eighty is red. Never use a lower grade. Specific gravity about nought point seven two; a hundred Imperial gallons at nought point seven weighs seven hundred pounds. Calorific value is the heat energy in the fuel. A volatile fuel brings vapour lock, cavitation and carburettor icing, worse with Mogas, and fuel boils at a lower temperature at altitude. Normal combustion is a controlled burn at sixty to eighty feet per second, peaking eight to ten degrees after top dead centre. Detonation happens after the spark, when the end gas explodes, and is caused by excessive temperature and pressure. The octane rating measures resistance to detonation, and higher compression needs higher octane. T E L reduces detonation. Pre-ignition comes before the spark, and a blocked vent makes the tank pressure fall.